Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹26.4 LAccepted-AOC 1 225 5 6 SADAR BAZAR DELHI CANTT 110010 | NEW DELHI | DELHI | 110010 | L1 | Accepted-AOC Being L1 Bidder | |
| 2 | L2₹32.5 L+₹3.6 L (12.5%)Rejected-AOC E 73 FF GALI NO 17B SADH NAGAR PALAM COLONY NEW DELHI 110045 | SOUTH WEST DELHI | DELHI | 110045 | L2 | Rejected-AOC Not L1 Bidder | |
| 3 | L3₹34.2 L+₹5.4 L (18.6%)Rejected-AOC ROOM NO 145 MASJID WALI GALLI GANESH MURTI NAGAR PART NO 2 COLABA MUMBAI 05 | L3 | Rejected-AOC Not L1 Bidder | |
| 4 | L4₹36.8 L+₹8.0 L (27.6%)Rejected-AOC 10 WARD NO 18 PLOT NO 34 KAMDENU FURNTIURE SIKAR RAJASTHAN 332025 | SIKAR | RAJASTHAN | 332025 | L4 | Rejected-AOC Not L1 Bidder | |
| 5 | L5₹38.5 L+₹9.6 L (33.3%)Rejected-AOC H NO 28 FIRST FLOOR E BLOCK KARMPURA WEST DELHI 110015 | WEST DELHI | DELHI | 110015 | L5 | Rejected-AOC Not L1 Bidder |
| Sl No | Description | Qty | Unit | Ridhi engineers and builders L8 | Sumit Enterprises L7 | Ruchi enterprises L4 | CHOUDHARY ELECTRICAL L3 | SUMIT ASSOCIATES L6 | M P TYAGI ENGINEERS AND CONTRACTORS L1 | GE WORLD L5 | PRASAD ELECTRICALS L2 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 1.00 | Demolition of cement concrete unreinforced, in ground floor or pavings below or above ground level from foundation of pump sets including removal of debris from site complete all as specified and as directed . | 3 | CUM | 450 ₹1,350 | 104 ₹312 | 400 ₹1,200 | 1,000 ₹3,000 | 900 ₹2,700 | 100 ₹300 Lowest | 100 ₹300 Lowest | 300 ₹900 |
| 2.00 | M&L for PCC 1:2:4 type B-1 using 20 mm graded mechanically crushed stone aggregates as in foundation, sub base or mass concrete complete all as specified and as directed. | 3 | CUM | 4,500 ₹13,500 | 3,211 ₹9,633 | 400 ₹1,200 Lowest | 1,500 ₹4,500 | 5,000 ₹15,000 | 2,000 ₹6,000 | 5,500 ₹16,500 | 2,500 ₹7,500 |
| 3.00Labour for Disconnecting of electrical connections from panel board including disconnecting the cable leads from the motor terminal box and taking down/out electric motor of following capacities from base plate of pump set after opening the nuts, bolts etc and transporting the motor to workshop for repair and back, re-installed after repair including testing complete all as specified and as directed. (Note :- (i) If the contractor fails to repair the motor and pump within seven days given to him the same will be got repaired through other agency by calling spot quotation at his risk and cost. This shall be in addition to penalty as mentioned in clause 7.1 of Particular Specification. The decision of the Accepting officer in this regard shall be final concluding and binding on the contractor. (ii) The contractor will open the Induction Motor/Pump at site only to assess the exect nature of reqpair required and material to be replaced. | |||||||||||
| 3.01 | 5-15 HP | 6 | EACH JOB | 500 ₹3,000 | 1,088 ₹6,528 | 200 ₹1,200 | 500 ₹3,000 | 1,000 ₹6,000 | 100 ₹600 Lowest | 350 ₹2,100 | 1,200 ₹7,200 |
| 3.02 | 20-30 HP | 15 | EACH JOB | 500 ₹7,500 | 1,522 ₹22,830 | 200 ₹3,000 | 800 ₹12,000 | 1,000 ₹15,000 | 100 ₹1,500 Lowest | 500 ₹7,500 | 2,000 ₹30,000 |
| 3.03 | 40-50 HP | 10 | EACH JOB | 900 ₹9,000 | 1,800 ₹18,000 | 200 ₹2,000 Lowest | 1,500 ₹15,000 | 2,000 ₹20,000 | 200 ₹2,000 Lowest | 1,000 ₹10,000 | 2,500 ₹25,000 |
| 3.04 | 60-75 HP | 6 | EACH JOB | 2,500 ₹15,000 | 2,512 ₹15,072 | 500 ₹3,000 | 2,000 ₹12,000 | 2,000 ₹12,000 | 200 ₹1,200 Lowest | 1,500 ₹9,000 | 2,500 ₹15,000 |
| 3.05 | 90-125 HP | 3 | EACH JOB | 4,500 ₹13,500 | 2,999 ₹8,997 | 400 ₹1,200 | 2,500 ₹7,500 | 2,000 ₹6,000 | 300 ₹900 Lowest | 2,500 ₹7,500 | 3,000 ₹9,000 |
| 4.00Labour for opening the electric induction motor of following capacity including taking down/out the burnt winding wire , cleaning the slots, rewinding the motor with super enamalled copper winding wire of existing gauge ,weight etc. including all other insulating material to make it functional complete all as specified and as directed . (Note:- Copper winding wire of approprioate guage will be measured in supply only) | |||||||||||
| 4.01 | 5-15 HP | 6 | EACH JOB | 500 ₹3,000 | 811 ₹4,866 | 900 ₹5,400 | 550 ₹3,300 | 3,500 ₹21,000 | 200 ₹1,200 Lowest | 3,500 ₹21,000 | 5,000 ₹30,000 |
Tender Value
₹45 L
EMD Value
₹90,000
Closing Date
8 Jul 2025, 6:00 pmClosed
GE U WATER SUPPLY DELHI CANTT 10
GE U WATER SUPPLY DELHI CANTT 10
REPAIR MAINT OF CENTRIFUGAL PUMP BOOSTER PUMP MONOBLOCK PUMP AND STARTOR AT PARED GROUND KABUL LINE AND ADJOINING PUMP HOUSES AREA IN THE AREA OF AGE U WS NOII UNDER GE U WATER SUPPLY DELHI CANTT 10
2025_MES_713552_1
GE/WS/Token No-13 OF 2025-26
Open Tender
Civil Works
Item Rate
180 days
GE U WATER SUPPLY DELHI CANTT 10
Please refer Tender documents.
5 documents required · 5 mandatory
₹500
GE U WATER SUPPLY DELHI CANTT 10
₹90,000
Yes
28 Aug 2025
10 Jun 2025
10 Jul 2025
10 Jun 2025
8 Jul 2025
24 Jun 2025
Amount
Demolition of cement concrete unreinforced, in ground floor or pavings below or above ground level from foundation of pump sets including removal of debris from site complete all as specified and as directed .
M&L for PCC 1:2:4 type B-1 using 20 mm graded mechanically crushed stone aggregates as in foundation, sub base or mass concrete complete all as specified and as directed.
Labour for Disconnecting of electrical connections from panel board including disconnecting the cable leads from the motor terminal box and taking down/out electric motor of following capacities from base plate of pump set after opening the nuts, bolts etc and transporting the motor to workshop for repair and back, re-installed after repair including testing complete all as specified and as directed. (Note :- (i) If the contractor fails to repair the motor and pump within seven days given to him the same will be got repaired through other agency by calling spot quotation at his risk and cost. This shall be in addition to penalty as mentioned in clause 7.1 of Particular Specification. The decision of the Accepting officer in this regard shall be final concluding and binding on the contractor. (ii) The contractor will open the Induction Motor/Pump at site only to assess the exect nature of reqpair required and material to be replaced.
Labour for opening the electric induction motor of following capacity including taking down/out the burnt winding wire , cleaning the slots, rewinding the motor with super enamalled copper winding wire of existing gauge ,weight etc. including all other insulating material to make it functional complete all as specified and as directed . (Note:- Copper winding wire of approprioate guage will be measured in supply only)
Supplying and Fixing in replacement of Motor Terminal Box of following capacity.
Supplying and Fixing in replacement of Motor Terminal Connection Plate of following capacity
Supplying and Fixing in replacement of CI Sleeve on Bearing Housing of following capacity
Supply and Fixing in replacement of Motor Cooling Fan as per site requirement for any size of motor made of PVC/ Aluminium complete.
Supply and Fixing in replacement of PVC cooling pipe with bush and addeptor complete.
Supply and Fixing in replacement of Brass air cock as per site requirement complete all as specified and directed.
Labour for Disconnecting and De-coupling the Centrifugal pump of following capacity from foundation after opening /cutting the rusted nuts, bolts etc including transporting the pump to workshop for repair and back, re-installed at existing position after repair and providing new MS nuts, bolts,packing flange etc including testing complete all as specified and as directed. (Note :- If the contractor fails to repair the motor and pump within the seven days given to him the same will be got repaired through other agency by calling spot quotation at his risk and cost. This shall be in addition to penalty as mentioned in clause 7.1 of Particular Specification. The decision of the Accepting officer in this regard shall be final concluding and binding on the contractor.)
Opening the centrifugal pump of following capacity, repairing the same by replacing the unserviceable spare parts including machining work and re-assembling the same in original position complete all as specified and as directed. (Note:- Spare Parts required shall be measured & paid spaerately.)
Supply Only in replacement of spare parts for Centrifugal pump of 5-15 HP Capacity.
CI Impeller
Pump shaft SS (AISI-410)
CI Casing wearing (Neckring)
CI interstage ring
CI stuffing box bush
CI Gland Plate
Eye bolt with nut
CI Shaft sleeve
Gasket Packing Set
Gland packing champion
Impeller key
coupling key
water liquid deflector
CI bearing cartridge DE/NDE
CI bearing plate
Coupling nut
MS Stud with nut
Labour only for Remetling of pump shaft, turning and balancing
Supply Only in replacement of spare parts for Centrifugal pump of 20-30 HP Capacity.
CI Impeller
Pump shaft SS (AISI-410)
CI Casing wearing (Neckring)
CI interstage ring
CI stuffing box bush
CI Gland Plate
Eye bolt with nut
CI Shaft sleeve
Gasket Packing Set
Gland packing champion
impeller key
coupling key
Water liquid deflector
CI bearing cartridge DE/NDE
CI bearing plate
Mechanical Seal
coupling nut
MS Stud with nut
Labour only for Remetling of pump shaft, turning and balancing
Supply Only in replacement of spare parts for Centrifugal pump of 40-50 HP Capacity.
CI Impeller
pump shaft SS (AISI-410)
CI Casing wearing (Neckring)
CI interstage ring
CI stuffing box bush
CI Gland Plate
Eye bolt with nut
CI Shaft sleeve
Gasket Packing Set
Gland packing champion
Impeller key
coupling key
water liquid deflector
CI bearing cartridge DE/NDE
CI bearing plate
Coupling nut
MS Stud with nut
Labour only for Remetling of pump shaft, turning and balancing
Supply Only in replacement of spare parts for Centrifugal pump of 60-75 HP Capacity.
CI Impeller
pump shaft SS (AISI-410)
CI Casing wearing (Neckring)
CI interstage ring
CI stuffing box bush
CI Gland Plate
Eye bolt with nut
CI Shaft sleeve
Gasket Packing Set
Gland packing champion
Impeller key
Coupling key
Water liquid deflector
CI bearing cartridge DE/NDE
CI bearing plate
Coupling nut
MS Stud with nut
Labour only for Remetling of pump shaft, turning and balancing
Supply Only in replacement of spare parts for Centrifugal pump of 90-125 HP Capacity. (Note:- Old U/s material obtained from demolition shall be taken on charge in demolition/salvage register and enter page number in demolition statement. Necessary RV in weight (KG) shall be taken into account and attach with RAR/F Bill)
CI Impeller
pump shaft SS (AISI-410)
CI Casing wearing (Neckring)
CI interstage ring
CI stuffing box bush
CI Gland Plate
eye bolt with nut
CI Shaft sleeve
Gasket Packing Set
Gland packing champion
impeller key
coupling key
water liquid deflector
CI bearing cartridge DE/NDE
CI bearing plate
coupling nut
MS Stud with nut
Labour only for Remetling of pump shaft, turning and balancing
Supply only in replacement of water seal/ Oil seal for any size of pump complete all as specified and directed.
Supply only in replacement of Oring set for any size of pump
Disconnecting of electrical connections from panel board including disconnecting the cable leads from the motor terminal box and taking down/out monoblock pump set capacity upto 10 HP from foundation/base plate of pump set after opening the nuts, bolts etc and transporting the pump to workshop for repair and back, re-installed after repair including testing complete all as specified and as directed . (Note :- If the contractor fails to repair the motor and pump within the seven days given to him the same will be got repaired through other agency by calling spot quotation at his risk and cost. This shall be in addition to penalty as mentioned in clause 7.1 of Particular Specification. The decision of the Accepting officer in this regard shall be final concluding and binding on the contractor.)
Opening the monoblock motor and pump upto capacity 10 HP , taking down/out the burnt winding wire and cleaning the slots including rewinding the monoblock motor with super enamelled copper winding wire of existing gauge ,weight etc. and repairing the pump by replacing the unserviceable spare parts including machining work and re-assembling the same in original position including all other insulating material complete all as specified and as directed. (Note :- Copper winding wire of appropriate gauge and spare parts of pump shall be measured and paid separetely.)
Supply Only in replacement of spare parts for Monoblock pump of upto 10 HP Capacity.
CI Impeller
Mechanical Seal
Water Seal
GM Shaft sleeve
Gland packing sheet
water liquid deflector
impeller Nut
MS Stud with nut
Disconnecting of electrical connections from panel board including disconnecting the cable leads from the motor terminal box and taking down/out dewatering motor pump vertical type/ centrifugal pump set from underground sump or from base plate of capacity upto 2.5 HP after opening the nuts, bolts etc and transporting the pump to workshop for repair and back, re-installed after repair including testing complete all as specified and as directed . (Note:- Copper winding wire and spare parts of motor and pump shall be measured and paid separetely. (Note :- If the contractor fails to repair the motor and pump within the seven days given to him the same will be got repaired through other agency by calling spot quotation at his risk and cost. This shall be in addition to penalty as mentioned in clause 7.1 of Particular Specification. The decision of the Accepting officer in this regard shall be final concluding and binding on the contractor.)
Opening of dewatering motor and pump/ centrifugal pump set of capacity upto 2.5 HP including taking down/out the burnt winding wire , cleaning the slots ,rewinding the motor with super enamelled copper winding wire of existing gauge ,weight etc. and repairing the pump by replacing the unserviceable spare parts including machining work and re-assembling the same in original position including all other insulating material complete all as specified and as directed. (Note :- Copper winding wire of appropriate gauge and spare parts of pump shall be measured and paid separetely).
Supply Only in replacement of spare parts of upto 2.5 HP Capacity dewatering motor and pump/ centifugal pump set .
CI Impeller-501/503
Maintenance kit -501/503
Cable kit with float switchfluid level controller-501/503 SE
Suction plate
Plug for motor cable
Installation kit-ama porter 500
stainless steel rotor sleeve
stainless steel rotor shaft -410
Remetailing of rotor & turning/grinding
GM suction ring
Prrof jointing of submersible cable
CI suction chamber
Repairing of stamping of stator
Mechanical seal set
O ring set
Insulation kit
Supplying and assembling super enamelled copper winding wire of appropriate gauge suitable upto 125 HP capacity Motor complete all as specified and directed.
Supply and Fixing in replacement of Ball bearing No 6305 or equivalent as per sample complete all as specified and as directed.
Supply and Fixing in replacement of Ball bearing No 6306 or equivalent as per sample complete all as specified and as directed.
Supply and Fixing in replacement of Ball bearing No 6307 or equivalent as per sample complete all as specified and as directed.
Supply and Fixing in replacement of Ball bearing No 6308 or equivalent as per sample complete all as specified and as directed.
Supply and Fixing in replacement of Ball bearing No 6309 or equivalent as per sample complete all as specified and as directed.
Supply and Fixing in replacement of Ball bearing No 6310 or equivalent as per sample complete all as specified and as directed.
Supply and Fixing in replacement of Ball bearing No 6311 or equivalent as per sample complete all as specified and as directed.
Supply and Fixing in replacement of Ball bearing No 6312 or equivalent as per sample complete all as specified and as directed.
Supply and Fixing in replacement of Ball bearing No 6313 or equivalent as per sample complete all as specified and as directed.
Supply and Fixing in replacement of Ball bearing No 6314 or equivalent as per sample complete all as specified and as directed.
Supply and Fixing in replacement of Ball bearing No 6315 or equivalent as per sample complete all as specified and as directed.
Supply and Fixing in replacement of double Ball bearing No 3307 complete all as specified and as directed.
Supply and Fixing in replacement of double Ball bearing No 3309 complete all as specified and as directed.
Supply and Fixing in replacement of double Ball bearing No 21309 complete all as specified and as directed.
Supply and Fixing in replacement of Roller bearing NU-313 complete all as specified and as directed.
Supply and Fixing in replacement of Roller bearing NU-314 complete all as specified and as directed.
Supply and Fixing in replacement of Roller bearing NU-316 complete all as specified and as directed.
Supply and Fixing in replacement of Roller bearing NU-318 complete all as specified and as directed.
SSupply and fixing spare tyre for coupling type as under, after taking down/out as existing at site complete all as specified and as directed.
type TC/P/011
type TC/P/013
type TC/P/014
type TC/P/015
type TC/P/017
type TC/P/018
Material and labour for painting Two coat of synthetic enamel paint as per existing pattern or scheme, on centrifugal pump & motor of any capacity rating 5-20 HP, Scratching the rusted and suction/ delivery pipeline including NRV and sluice valve, MS Base channel including preparation of surfaces by scratching and removing the rust complete all as specified and as directed. (Note:- (i) Number plate and other details on the motor will NOT be painted and must be kept neat and clean while painting. (ii) Painting will be done by hand brush and No spray gun will be used while painting in site.)
Material and labour for painting Two coat of synthetic enamel paint as per existing pattern or scheme, on centrifugal pump & motor of any capacity rating 25-50 HP, Scratching the rusted and suction/ delivery pipeline including NRV and sluice valve, MS Base channel including preparation of surfaces by scratching and removing the rust complete all as specified and as directed. (Note:- (i) Number plate and other details on the motor will NOT be painted and must be kept neat and clean while painting. (ii) Painting will be done by hand brush and No spray gun will be used while painting in site.
Material and labour for painting Two coat of synthetic enamel paint as per existing pattern or scheme, on centrifugal pump & motor of any capacity rating 60-75 HP, Scratching the rusted and suction/ delivery pipeline including NRV and sluice valve, MS Base channel including preparation of surfaces by scratching and removing the rust complete all as specified and as directed. (Note:- (i) Number plate and other details on the motor will NOT be painted and must be kept neat and clean while painting. (ii) Painting will be done by hand brush and No spray gun will be used while painting in site.
Material and labour for painting Two coat of synthetic enamel paint as per existing pattern or scheme, on centrifugal pump & motor of any capacity rating 90-125 HP, Scratching the rusted and suction/ delivery pipeline including NRV and sluice valve, MS Base channel including preparation of surfaces by scratching and removing the rust complete all as specified and as directed. (Note:- (i) Number plate and other details on the motor will NOT be painted and must be kept neat and clean while painting. (ii) Painting will be done by hand brush and No spray gun will be used while painting in site.
Supply and Fixing in replacement MS base channel of size as exists including cutting, welding and making hole including applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.
Supply and fixing bearing plate bolt of size 8 mm dia , 100 mm long after taking down/out plate as existing at site complete all as specified and as directed.
Supply and Fixing in replacement of MS foundation bolts with nuts and washers, size 20mm dia , 250 mm long complete all as specified and as directed.
Supply and fixing in replacement 3 pole power contactor type ML-1.5, 415 Volts, 50 HZ range 25 Amps complete all as specified and as directed.
Supply and fixing in replacement 3 pole power contactor type ML-2, 32 Amps, 415 Volts, 50 HZ complete all as specified and as directed.
Supply and fixing in replacement 3 pole power contactor type ML-3, 40 Amps, 415 Volts, 50 HZ complete all as specified and as directed.
Supply and fixing in replacement 3 pole power contactor type ML-4, 70 Amps, 415 Volts, 50 HZ complete all as specified and as directed.
Supply and fixing in replacement 3 pole power contactor type ML-6,110 Amps, 415 Volts, 50 HZ complete all as specified and as directed.
Supply and fixing in replacement 3 pole power contactor type ML-10, 200 Amps, 415 Volts, 50 HZ complete all as specified and as directed.
Supply and fixing in replacement of Thermal Overload Relay ML-1 10 to 16 complete all as specified and as directed.
S & F in replacement of Bimetal over load relay type MN 2, relay range 14-23 Amp complete all as specified and as directed.
S & F in replacement of Bimetal over load relay type ML 2/3, relay range 20-32 Amps complete all as specified and as directed.
S & F in replacement of Bimetal over load relay type ML 2/3, relay range 28-42 Amps complete all as specified and as directed.
S & F in replacement of Bimetal over load relay type MN 5, relay range 45-75 Amps complete all as specified and as directed.
S & F in replacement of Bimetal over load relay type ML 5, relay range 66-110 Amps complete all as specified and as directed.
S & F in replacement of Bimetal over load relay type MN-12, CT operated relay range 90-150 Amps complete all as specified and as directed.
Supply and fixing in replacement Amp Meter Analog type 0 to 60 Amp of size 96 x 96 mm complete all as specified and as directed.
Supply and fixing in replacement Amp Meter Analog type 0 to 100 Amp of size 96 x 96 mm complete all as specified and as directed.
Supply and fixing in replacement Amp Meter Analog type 0 to 200 Amp of size 96 x 96 mm complete all as specified and as directed.
Supply and fixing in replacement of Indicating light RYB LED type complete all as specified and as directed.
Supply and fixing in replacement Amp Meter Digital type of size 96 x 96 mm complete all as specified and as directed.
Supply and fixing in replacement Volt Meter digital type of size 96 x 96 mm complete all as specified and as directed.
Supply and fixing in replacement FRLS PVC insulated industrial grade copper conductor wire of following size, 1100 volts complete all as specified and as directed.
4.00 sqmm, single core
6.00 sqmm, single core
10.00 sqmm, single core
16.00 sqmm, single core
25.00 sqmm, single core
35.00 sqmm, single core
50.00 sqmm, single core
Supply and fixing in replacement PVC insulated FRLS round sheathed copper conductor wire of 2.5 Sqmm, 3 core, 1100 volts complete all as specified and as directed.
Supply and fixing in replacement of Thermal contactor type MNX-18, in electric panel of motor complete all as specified and as directed.
Supply and fixing in replacement of Thermal contactor type MNX-25 in electric panel of motor complete all as specified and as directed.
Supply and fixing in replacement of Thermal contactor type MNX-32 in electric panel of motor complete all as specified and as directed.
Supply and fixing in replacement of Thermal contactor type MNX-40 in electric panel of motor complete all as specified and as directed.
Supply and Fixing in replacement Electronics Timer 3-30 seconds, Type ST100, 415 volts, complete all as specified and as directed.
Supply and fixing in replacement moulded case circuit breakers (MCCB), 3 pole, 100 Amps with breaking capcity 16 KA , 415 volts, complete all as specified and as directed.
Supply and fixing in replacement moulded case circuit breakers (MCCB), 3 pole, 160 Amps with breaking capcity 25 KA , 415 volts, complete all as specified and as directed.
Supply and fixing in replacement moulded case circuit breakers (MCCB), 3 pole, 200 Amps with breaking capcity 36 KA , 415 volts, complete all as specified and as directed.
Supply and fixing in replacement moulded case circuit breakers (MCCB), 3 pole, 250 Amps with breaking capcity 36 KA , 415 volts, complete all as specified and as directed.
Supply and fixing in replacement moulded case circuit breakers (MCCB), 3 pole, 400 Amps with breaking capcity 50 KA , 415 volts, complete all as specified and as directed.
Supply and fixing in replacement moulded case circuit breakers (MCCB), 3 pole, 630 Amps with breaking capcity 50 KA , 415 volts, complete all as specified and as directed.
Supply and fixing in replacement of Submersible panel board MUG 6 starter type suitable upto 10 HP
Supply and fixing in replacement of fully automatic star delta starter type with sheet metal encloser MN 25 FASD
Supply and fixing in replacement of fully automatic star delta starter type complete with sheet metal encloser ML-3
Supply and fixing in replacement of fully automatic star delta starter type complete with sheet metal encloser ML-4
Supply and fixing in replacement of fully automatic star delta starter typecomplete with sheet metal encloser ML-6
Supply and Fixing in replacement Automatic phase sequence correctot suitable for 51-75 HP with sheet metal encloser and indicator lamp output/input, suitable for 3 Phase electric motor with Automatically protection against single phaseing voltage, unbalanced and low/High voltage with time delay.
Supply and Fixing in replacement Automatic phase sequence correctot suitable for 76-100 HP with sheet metal encloser and indicator lamp output/input, suitable for 3 Phase electric motor with Automatically protection against single phaseing voltage, unbalanced and low/High voltage with time delay.
Supply and fixing in repair copper terminals lugs (Thimbles) ring type medium duty for following items :-
Supply and fixing, install, test and commissioning of LT Feeder pillar box outdoor type totally enclosed with front and rear opening hinged doors with canopy sloped top projected and raised platform of suitable sizes weather dust vermin proof made out of 3.15mm thick CRCA sheet, factory made (CPRI approved manufacturer) powder coated painted as approved colour, copper bus bar suitable for 3 phase 4 wire LT, AC, 50Hz, 433 volts, 350 Amps capacity RYBN insulated with sleeved insulation complete with multifunctional meter LED type by showing Amps, volts, frequency etc along with suitable size of CT on outgoing, indicating lamp RYB, complete internal wiring with suitable size of PVC insulated copper conductor cable, including cable glands and lugs for incoming and out going LT cables as per required sizes, PCC platform made out of 1:2:4 type B1 and pedestal of 30 cm height from GL with suitable nut, bolts, washers etc., all as specified and directed for suitable to in and including accomodate the following items and all as specified and directed by dismantling exisiting unserviceable LT panel complete. (a) 01 x 200A 36 KA 4 Pole - Incoming MCCB's (b) 02 x 63A 25 KA 3 Pole - Outgoing MCCB's (c) 01 x 63 Amps 3 Phase Auto Phase Sequence Corrector (d) 02 x Thermal Over load relay - outgoing (e) 02 x ST 100 Timer - outgoing (f) ML2 FASD (Heavy duty 35 HP relay range 13-21 A) - 02 Nos for outgoing (Note :- Contractor shall be take approval of Accepting Officer for panel drawing before fabrication work.)
Supply and fix in Replacement of Earthing complete with galvanised iron earth plate electrode of size 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of the plate not less than 1.5mtr below normal ground level, connected to galvanised iron strip 32 x 6mm as earth continuity conductor connected to earth plate by means of GI light bolt nuts, check nuts and washers of including providing earth wire protection pipe GI light grade 40mm bore from earth plate to main switch board/panel, watering pipe 40mm bore GI pipe medium grade with wire mesh and funnel at top, earth pit of PCC in 1:2:4 type B-1, with RCC cover 1:2:4 type B-0 using MS TMT 8mm dia @ 150 c/c both way with suitable handle, angle iron frame made out of angle iron of size 40 x 40 x 4mm, including adequate quantity of charcoal dust and salt in alternate layers all around the earth plate, including excavation and earth work in any type of soil complete all as per electrical plate No 3 of SSR Part-I (2009) connected to earthing test point including test point made out of 40 x 3mm GI flat iron, all as specified and indicated including testing on completion, including taking down old unserviceable earthing, for machinery/ equipment installed at power house/sub station complete all as specified and directed.
M & L for earthing in replacement GI plate 60×60cm ×3.15mm thick electrode and 32x6mm galvanised strip as earthing lead thick buried directly in ground vertically to a depth not less than 2.25 mtr below normal ground level, connected to copper strip of size 25x4mm as earth lead by means of bolts, nuts and washers madeout of copper or tinned brass and protection GI pipe of 40mm dia all as specified and testing complete including earthwork, PCC chamber, RCC chamber cover with handle GI watering pipe 20mm dia, GI funnel with wire mesh, magnesium sulphate, salt, charcoal, lugs etc and method of earthing shall be as per plate No :3 of SSR part -I.
Supply & Fix in replacement, commissioning and testing of LT panel board indoor type floor mounted of factory made powder coated made out of outside body of 3.15mm thick steel sheet and inside body 14 gauge steel sheet, locking arrangement, front side and rear side opening arrangement of suitable size, Incl mounted on Angle iron stand of size 50x50x6mm having minimum height 1.5 feet duly grouted or welded on floor. Aluminium bus bar TPN of 400 A for MCCB to all feeders to accommodate following items.
Incoming MCCB 200 Amp 50 KA 4 pole-01 No
Outgoing MCCB 100 amp 35/36 KA 3pole -02 Nos
RYB indication for each incoming & outgoing supplies-01 set
Termination of all cables with suitable size thimble and gland-1 Job
Fully Automatic star delta motor starter 50 hp (37.5KW) ,with single phase protuction , timer stardelta, relay AC-3, 415V,50 Hz, 3 Phase, relay range 30 to 50 AMP
Termination of all cables with suitable size thimble and gland-1 job
Note :- Contractor shall be take approval of Accepting Officer for panel drawing before fabrication work.
Supply and fixing, install, test and commissioning of LT Feeder pillar box outdoor type totally enclosed with front and rear opening hinged doors with canopy sloped top projected and raised platform of suitable sizes weather dust vermin proof made out of 3.15mm thick CRCA sheet, factory made (CPRI approved manufacturer) powder coated painted as approved colour, copper bus bar suitable for 3 phase 4 wire LT, AC, 50Hz, 433 volts, 600 Amps capacity RYBN insulated with sleeved insulation complete with multifunctional meter LED type by showing Amps, volts, frequency etc along with suitable size of CT on outgoing, indicating lamp RYB, complete internal wiring with suitable size of PVC insulated copper conductor cable, including cable glands and lugs for incoming and out going LT cables as per required sizes, PCC platform made out of 1:2:4 type B1 and pedestal of 30 cm height from GL with suitable nut, bolts, washers etc., all as specified and directed for suitable to in and including accomodate the following items and all as specified and directed by dismantling exisiting unserviceable LT panel complete.
The panel shall consist of following components-(a) 01 x 250A 36 KA 4 Pole - Incoming MCCB's (b) 02 x 100 A 25 KA 3 Pole - Outgoing MCCB's (c) 01 x 100 Amps 3 Phase Auto Phase Sequence Corrector (d) 02 x Thermal Over load relay - outgoing (e) 02 x ST 100 Timer - outgoing (f) ML3 FASD (Heavy duty 50 HP with suitable relay range) - 02 Nos for outgoing Note :- (i) Contractor shall be take approval of Accepting Officer for panel drawing before fabrication work.
Supply of L.T. Panel, indoor type, CPRI tested (IP-65, conforming to IS / IEC 61439 -1&2, with 65 KA 1 sec,) made out of outer sheet 3.15mm and inner sheet 2mm sheet, front and back openable, with proper locking arrangement, Aluminum bus bar 800 Amps, 4 Pole, duly insulated with color coated heat shrinkable sleeves and shall be mounted on suitable size/rating of epoxy resin insulator. Provision of aluminum earthing strip, size: 25 X 5 mm throughout the panel at bottom, Angle base frame 50x50x5mm of height 45 cm above from ground. Panel shall be suitable for 3 phase 4 wire 415 volts AC supply, 50 HZ, dust weather and vermin proof. Panel shall be powder coated siemens grey shade No. 7032. The panel shall consist of following components- a) MCCB 250/3P/36KA, Thermal & Magnetic adjustable, ICU 100% - 01 no. b) Multifunction meter VAF+PF - 01 No. c) R.Y.B. Indicating Lights - 02 Nos. d) C.T.s 0-250 Amp. e) FASD ML6 (105HP) O/L Relay 66-110 Amp. in sheet enclosure - 01 No. f) Phase Sequence Relay -------------- 01 No. g) Contactors ML-10 ------ 02 Nos. h) MCCB 400/4P/50KA, Thermal & Magnetic adjustable, ICU 100% as incomer - 01 no. Note :- Contractor shall be take approval of Accepting Officer for panel drawing before fabrication work.
Supply of L.T. Panel, indoor type, CPRI tested (IP-65, conforming to IS / IEC 61439 -1&2, with 65 KA 1 sec,) made out of outer sheet 3.15mm and inner sheet 2mm sheet, front and back openable, with proper locking arrangement, Aluminum bus bar 800 Amps, 4 Pole, duly insulated with color coated heat shrinkable sleeves and shall be mounted on suitable size/rating of epoxy resin insulator. Provision of aluminum earthing strip, size: 25 X 5 mm throughout the panel at bottom, Angle base frame 50x50x5mm of height 45 cm above from ground. Panel shall be suitable for 3 phase 4 wire 415 volts AC supply, 50 HZ, dust weather and vermin proof. Panel shall be powder coated siemens grey shade No. 7032. The panel shall consist of following components.
MCCB 250/3P/36KA, Thermal & Magnetic adjustable, ICU 100% - 03 No.
Multifunction meter VAF+PF - 01 No.
R.Y.B. Indicating Lights - 04 Nos.
C.T.s 0-250 Amp.
FASD ML-4 (75HP) O/L Relay 45-75 Amp. in sheet enclosure - 03 Nos.
Phase Sequence Relay - 03 No.
Contactors ML-6 (110 Amp) - 06 Nos.
MCCB 630/4P/50KA, Thermal & Magnetic adjustable, ICU 100% as incomer- 01 No.
(Note :- Contractor shall be take approval of Accepting Officer for panel drawing before fabrication work.)
An amount of Rs 2,78,625.00 shall be deducted from BOQ on account of schedule of credit
PRASAD ELECTRICALS (BID ID -3351622)
CHOUDHARY ELECTRICAL (BID ID -3343376)
Ruchi enterprises (BID ID -3343290)
GE WORLD (BID ID -3343303)
SUMIT ASSOCIATES (BID ID -3351451)
Sumit Enterprises (BID ID -3351716)
Ridhi engineers and builders (BID ID -3351695)
stage.html
html • 0.06 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .