REPAIR/REPLACEMENT OF SEWAGE LINES MANHOLES SCEPTIC TANK BRICK DRAIN AND CERTAIN MISC B/R WORKS AT AF STATION DHANSA UNDER GE AF GURGAON

Amount

M&L for removal of blokage in sewage line between manholes of various sizes by any means by using Kambore NM-01 No Kamgarb 5 Ltr 01 No, Kambore 1075 up-01 Nos Retriever 150 including removing Rugs of any type, dirt etc complete upto the entire satisfaction of Engr-in-Charge Note : (i) The rates quoted in the above item includes cost of T&P like Kambore NM-01 No Kamgarb 5 Ltr 01 No & Retriever 150 etc complete. (ii) The lines measured once can not measured again within three months, if block in the same lines re-occure with in three months the contractor has to remove the blockage and shall not be paid extra for this (iii) Minimum two persons shall be deployed by contractor and they shall be present on all working days for attending the complaints of Sewage. The complaints shall be detailed by JE/AGE concerned. In case of non attending of complaints within 20 hours except on holidays, the recovery @ Rs 100/- per complaint shall be made from contractors dues. (iv) All the above machineries shall be procured and shall be deposited in complaint cell of AGE B&R-II, AF Station Palam within 20 days on commencement of the work

M&L for removal of blokage of soil/waste pipes WC, WHB,Bottle Trap, Floor Trap etc running on external wall of buildings, complete all as specified and directed

Cleaning of manhole upto 1 m depth and removal of sludge silt/liquid/mud/sand/water etc in foul position to outside the MoD land complete all as specified and directed

All as per item No 3 here-in-before but exceeding 1m and not exceeding 2m in depth.

All as per item No 3 here-in-before but exceeding 2m and not exceeding 3 m in depth.

Excavation in trenches not exceeding 1.50m wide and not exceeding 1.50m in depth and not exceeding 10 Sqm on plan and not exceeding 1.50 m in depth for manholes ,well etc and getting out in soft/loose soil, complete all as specified and directed

All as per Srl Item No 6 here-in-before but depth exceeding 1.50m and not exceeding 3m.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm complete all as specified.

Removing excavated materials to a distance exceeding 50m but not exceeding 200m and depositing where directed at a level not exceeding 1.50m above the starting point in soft/loose soil, complete all as specified.

Demolition & breaking up drain pipes (salt glazed stone ware, AC or reinforced concrete) set in cement mortar including bed concrete internal dia of pipe 150mm and removal of demolished materail out of MoD land complete all as specified.

All as per Srl item No.10 here-in-before but internal dia 200mm.

Material and Labour for concrete bed to 150 mm bore drain pipes in cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregates including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

All as per item No 12 here-in-before but bore of pipe 200 mm.

Material and Labour for 150 mm internal dia reinforced cement concrete pipes drain pipes class NP-3aid in trenches and jointed complete all as specified.

All as per Srl item No. 14 here-in-before but internal dia of pipe 200mm.

Supply and Fixing in repairs, SFRC man hole cover of size 600mm dia x70mm thick with frame set in cement mortar 1:4 complete all as specified and as directed . Notes: - (i) Make of SFRC Manhole/drain cover : (a) M/s PS Concrete. (b) M/s KK Manhole.(c) Or equivalent as approved by GE. (ii) Contractor will provide manufacturer test certificate of SFRC cover & frame

Supply and Fixing in repairs, SFRC manhole cover of size 600mm x 600mm x 70mm thick with frame set in cement mortar 1:4 complete all as specified and as directed. Notes: - (i) Make of SFRC Manhole/drain cover and frame : (a) M/s PS Concrete. (b) M/s KK Manhole.(c) Or equivalent as approved by GE (ii) Contractor will provide manufacturer test certificate of SFRC cover & frame

Supply and Fixing in repairs, SFRC cover slabs of size 450mm x 450mm x 40mm thick with frame set in cement mortar 1:4 complete all as specified and as directed Notes-(i) Make of SFRC Manhole/drain cover and frame : (a) M/s PS Concrete (b) M/s KK Manhole.(c) Or equivalent as approved by GE (ii) Contractor will provide manufacturer test certificate of SFRC cover & frame

Supply and Fixing in repairs, 110mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including suitable clamps complete all as specified and as directed

Supply and Fixing in repairs, PVC (SWR) bends, 110mm dia fixed to PVC pipes complete all as specified and directed

Supply and Fixing in repairs, 80 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including suitable clamps complete all as specified and as directed

Supply and Fixing in repairs, PVC (SWR) bends, 80 mm dia fixed to PVC pipes complete all as specified and directed

Dismantling of MS/CI pipe including fittings of any description, any dia, all as specified and as directed

Supply and Fixing for cast iron, sand cast, soil, waste & vent pipes, 100mm bore in any length with or without ears with cement joints fixed to walls complete all as specified and as directed by Engr-in-Charge.

Supply and Fixing for cast iron, sand cast soil waste & vent pipes 75mm bore in any length with or without ears with cement joints fixed to walls complete all as specified and as directed

Supply and Fixing CI branch piece single/Tee etc (equal or unequal) ordinary or invented (spigot or socket type) or with parallel branches, bore of pipe 100mm complete all as specified and directed.

Supply and Fixing cast iron branch piece/Tee etc 75mm bore size with oval access door single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches complete all as specified and as directed

Supply and Fixing cast iron bends any radius, diminishing pieces or tapers 100mm bore size complete all as specified and as directed

All as per Srl item No 28 here-in-before but for 75 mm bore.

Supply and Fixing in repairs, SFRC drain cover of size 900mm x 600mm x 70mm thick laid over existing drain complete all as specified and as directed by Engr-in-Charge. Notes: - (i) Make of SFRC Manhole/drain cover and frame : (a) M/s PS Concrete (b) M/s KK Manhole.(c) Or equivalent as approved by GE (ii) Contractor will provide manufacturer test certificate of SFRC cover & frame

Supply and Fixing in repairs, SFRC drain cover size1200mm x 300mm x 70mm thick laid over existing drain complete all as specified and as directed by Engr-in-Charge. Notes: - (i) Make of SFRC Manhole/drain cover and frame : (a) M/s PS Concrete.(b) M/s KK Manhole.(c) Or equivalent as approved by GE (ii) Contractor will provide manufacturer test certificate of SFRC cover & frame

Demolition of Brickwork built in cement mortar including all quioins, arches, pillars etc complete all as specified and as directed .

Supply only Water Proofing compound complete all as directed.

Taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed

M&L for brickwork with subclass `B` bricks, in straight or curved on plan exc 6m mean radius, built in CM 1:6 complete all as specified and as directed

M&L for cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in copings/benching including use of necessary formwork etc complete all as specified.

M&L for rendering 15mm thick in CM 1:4 with water proofing compounding @3% by weight of cement on fair faces of brick work or concrete surfaces in cement mortar 1:4, finished even and smooth without using extra cement complete all as specified. Note: WPC shall be measured and paid seperately.

M&L for preparation of newly plastered surfaces of wall and applying two coats of weather proof exterior emulsion paint over a coat of primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint on walls. complete all as specified.

M&L for preparation (Complete removal of existing treatment) of old decorated external wall/ceiling surface of existing treatment by scrapping with Trucare Wall Sander : L-01/H-01 (having mechanical vaccum mechanism) having RPM not less than 1500, sand pad of 80 grit having dia of 7"/9" to make the surface free from dust, loose paint etc or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and applying Two coats of wheather proofing exterior acrylic emulsion paint over priming coat premium quality on wall/ceiling surface including applying 2mm thick wall care putty over disturbed surface during preparation of any reason, sand papering thus make surface smooth upto 3 storey buildings complete all as specified and directed. Note : (a) Stage for Preparation of surfaces shall be got approved from Engg-In-Charge before applying the finishes. (b) Material shall be procured from manufacturer and work shall be got executed through authorised applicator.

S&F in repairs salt-glazed stone ware gully traps size 150X150mm square or round mouthed type 'P' including CI cover complete all as directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified.

M & L for hard core of gauge n exc 63mm, deposited spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified.

M & L 100mm thick cement concrete type D2, 1:4:8 (Using 40mm graded stone aggregate) as in sub base including use of necessary form work complete all as specified.

M&L for 50mm thick PCC 1:2:4, type B1, using 20mm graded aggregate as in floor finished even and smooth without using extra cement including use of necessary form work complete all as specified.

M & L for 38mm wide glass dividing strips, 3mm thick, inserted in position, conforming to design complete all as specified.

M&L for 75 mm thick cement concrete (1:4:8) type D-2 with using 40 mm graded stone aggregates) as in sub base of flooing etc complete all as specified.

S& F for machine pressed precast concrete interlocking paver block any shape and size,with grey cement and pigment to match, confirming to IS 15658-2006 of 60mm thick M-35 grade laid over 50 mm thick sand cushioning complete all as specified.

M&L for screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:6) for laying floor finishes complete all as specified.

M&L for chequered cement concrete coloured tiles 30 cm x 30 cm x 25mm, set jointed and pointed in neat cement slurry in floors with grey cement and pigment complete all as specified.

S&F in repair of Steel rolling shutters OF 1.25mm thick lath thickness, with out ball bearing, as specified including top cover, an choring rod, hasp and staple and one shop coat of primer; erected in position as indi cated, complete: push pull or manual type complete all as specified and directed.

M&L for cement concrete type B0 1:2:4 (using 12.50 mm graded stone aggregate) as in coping benching, gola, slightly rounded and similar items complete all as specified.

M&L for PCC 1:3:6 type C-1 (using 20mm graded stone aggreate), 75 mm thick as in plinth protection including finishing the surface even & smooth without using extra cement complete all as specified.

M&L for cement concrete type B-1 (1:2:4) with using 20mm graded stobe aggrgates) as in surface channels and drains complete all as specified.

Dismanting of stone slab and tiles laid bedded and pointed in any mortar of any size description or thickness in floor, appron etc. complete all as specified.

M&L for 18-20 mm thick Granite tiles machine cut , bedded and jointed with grey cements slurry and pointed with white or colour cement with admixture of pigment to match the shade of granite stone including grinding & polishing slab over screed bed or bedding layer of mortar 15 mm thick in cement mortar (1 : 4) laid complete all as specified.

M&L for 18-20 mm thick Granite tiles machine cut, in skirting/dado laid over cement mortar and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over 10 mm thick rendering in cement mortar (1:4) on vertical surfaces for backing of tiles complete all as specified.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each complete all as specified and directed.

All as per item No. 58 here-in-before but exc 1.5 Sqm and not exc 4 Sqm each complete all as specified.

Taking down shutter of any description exc 1 Sqm and n exc 2 Sqm and removing from site complete all as specified.

S&F for Pressed steel frames 125X60mm (made out of 1.25mm thick MS Sheet) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified.

S&F for Pressed steel frames 105X60mm (made out of 1.25mm thick MS Sheet) for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified.

S&F factory made 35mm thick flush shutters , solid core construction with block board core and plywood face pannel commercial type on both faces complete all as specified.

S&F factory made 35mm thick 2nd class hardwood glazed and skelton door shutters, open rebated and prepared to receive glass, gauze, (without sash bars) edges for framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-1 section 8 clause 8.24 (a) fitted to chowkats complete all as specified.

M&L preparation of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed.

S&F solid PVC door frame of size 50mm X47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specification and as directed.

S&F factory made PVC shelter panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement , supplying and fixing in the frame at site as per specification & drawing as specified.

S&F 100 mm Butt hinges, Stainless steel and fixed complete all as specified and as directed.

S&F 200mm long aluminium anodised, barrel tower bolts of extruded section complete all as specified.

S&F 150 mm size extruded aluminium alloy handles fabricated type anodised and fixed complete all as specified.

S&F 250 mm long aluminium alloy anodised sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast sections or cast aluminium alloy complete all as specified and as directed.

S&F in repair Mortice lock, vertical type of brass 100 mm 4 Levers with duplicate keys complete all as specified.

S&F in repair aluminium (Die cast) body Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified.

S&F window or ventilators section of frame 72x55mm fixed to wall or concrete surface with rowl plugs made of galvanised steel powder coated and section of shutter 47x20mm mulion section 72x50mm (Based steel as per IS 513 "D" quality galanised as per IS 277 with zinc of 120 gms/sqm) glazed or gauged and wire gauge shutter prepare to receive wire mesh to the shutter (Double door shutter) with total coated thickness of 0.6mm including grills/guard bars made of square bars powder coated fixed to window frame with screws including necessary fittings and all builders hardware such as handles, tower bolts and stays etc complete all as specified and as directed. Make : NCL type-4000 Series (Note : Glass and wiremesh shall be measured and paid separately under respective items)

S&F Powder coated Aluminium frame for doors, windows, ventilators with or more rebates including jointing cleat for fixing etc. Complete all as specified.

S&F Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified.

S&F Anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

Taking down of aluminium doors/window any type any description and re-fixing in same opening after necessary repairing such as floor spring, locks, hinges, glass, rubber beading, handles, tower bolts etc complete all as specified and as directed. Note Cost of screws, misc items shall be included in the quoted rate .

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple including necessary beading complete all as specified.

S&F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple including necessary beading complete all as specified.

Hacking out old broken glass (any thickness, size, quality or escription) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

S&F sheet glass 4mm thick ordinary quality and glazing with oil putty or wooden beads complete all as specified.

S&F in repair white vitreous China wash down water closet pan (pedestal pattern), and trap (excluding fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc. complete all as specified.

S&F as in repair vitreous china squatting pan, white, orissa pattern, size 580x440mm with integral foot rests (excluding flushing cistern & flush pipe) with cast iron ‘P’ trap incl lime concrete bedding and making good to the disturbed surface to match with the existing surface of floor complete all as specified and as directed

S&F in repair vitreous china wash hand basin (flat back) of size 550x400mm with padestal including one number chromium plated waste fittings, 32 mm dia, brass with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, with & including 32 mm dia PVC waste pipe with connector, including cutting for and pinning in ends of brackets complete all as specified.

S&F in repair of plastic water closet sheet covers white closed pattern with flat bottom, with mild steel chromium plated or aluminised hinging device complete all as specified.

S&F in repair fancy type Angle stop cock with flange, 15 mm nominal bore, brass, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified.

S&F in repair angular two way angle cock with wall flange, 15 mm nominal bore cast copper alloy, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified.

S&F in repair pillar taps, cast copper alloy, with capstan heads, fancy type chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for 15mm bore iron pipe and fixed complete all as specified.

S&F in repair bib taps, long body, brass, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified.

S&F in repairs PVC white low level flushing cistern 10 ltr capacity with all fittings syphonic action type with inlet ball valve and float, handle with & including bracket and PVC flush pipe 32 mm bore complete all as specified.

S&F in repair PVC connection 450 mm long suitable for 15 mm GI pipe with two brass nuts & rubber washers complete all as specified.

S&F in repair tubular towel rail 20mm dia type brass chrormium plated 600mm long between flanges complete all as specified and as directed

S&F in repair chromium plated shower roses 125 mm size with or without swivel joints of standard size including fixing to 15mm steel pipe or union complete all as specified.

S&F in repair Corner glass shelf (with bracket) , fancy type with stainless steel railing fixed to wall with rawl plugs and chromium plated screws complete all as specified and directed.

S&F in repair fancy type central hole basin mixer without PUW with 450 mm flexible hose copper alloy with capstan heads CP screwed down high pressure with or without lettered Hot or cold with long screwed shanks and fly nuts screwed for iron pipe fixed complete all as specified.

S&F in repair chromium plated health faucet telephonic type with 8mm dia, 1 meter long CP flexible with wall hook and jet of approved make, suitable for 15 mm bore iron pipes or for unions and fixed complete all as specified.

S&F in repair soap dish, brass, chromium plated,, fancy type fixed to wall with rawl plugs and chromium plated screws complete all as specified.

S&F in repair toilet paper holder ,brass, chromium plated,, fancy type fixed to wall with rawl plugs and chromium plated screws complete all as specified.

S&F in repair 200 mm dia towel ring ,brass, chromium plated,, fancy type fixed to wall with rawl plugs and chromium plated screws complete all as specified.

S&F in repair towel Rack 600 mm with hanger ,brass, chromium plated, fancy type fixed to wall with rawl plugs and chromium plated screws complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles from site and rubbish off the premises complete all as specified.

M&L for screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:6) for bedding of tiles complete all as specified.

M&L for 10 mm thick rendering in cement mortar (1:4) on vertical surfaces for backing of tiles complete all as specifed.

M&L for joint free Non- skid ceramic coloured tiles 7 to 8mm thick (Square/ rectangular) area of each tile exceeding 0.11 but n.exc 0.18 Sqm, in floors/shirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L joint free Glazed ceramic coloured/ printed tiles in vertical surface of size 350x 250 x 6-7mm/450x 300 x 6-7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match on walls as in dado/ skirting etc complete all as specified.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified & directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified & directed.

Dismantling mild steel work of any description not otherwise provided for complete all as specified and directed.

S & F Rolled Mild Steel Plates (plain or Chequered) channels, square cut or notched, forming holes, without any attachment confirming to Fe 410-S complete all as specified.

S&F steel work as in tubular, rafters, purlins, posts and similar work (round/sqare/rectangular shape of pipes as approved by Engr-in-charge ) trusses of semi circle/ curved shape up to height 6 mtr including post special shaped washers etc complete incl necessary nut bolts wind ties and gusset plates etc using ERW or induction butt welded tubes conformining to IS 1161-1998 garde St-240 complete all as specified.

M&L for excavating in post holes (or similar holes) each n.exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25CM, in any type of soil complete all as specified.

M&L cement concrete type B-2, 1:2:4 using 40mm graded aggregate as in foundations, filling and mass concrete complete all as specified.

S&F Mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes for notching of wire, etc, flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work etc complete all as specified and as directed.

S&F Mild steel bolts, screwed one end,with hexagonal or square nuts and washers, the other end Exc 5 cm and n.exc 10cm long and Diameter of neck in 11 to 15 mm complete all as specified and directed.

M&L for Mild Steel deformed or round bars or 10 mm dia and above, cut to length bent to required shape incl cranking, bending and binding with Mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for Preparation of new steel and iron surfaces of any description, over 10 cm in width or girth , not otherwise described and painting with two coats of synthetic enamel paint over a coat of red oxide primer etc complete all as specified and as directed.

Dismantling fencing wire mesh, any type complete all as specified and as directed.

Fixing only chain link fencing including linewires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire

Supply only Chain link MS galvanisd fencing, any size or type complete all as specified.

Taking down barbed wire fencing of any description and in any position fixed to RCC/steel posts complete all as specified and directed. (each row shall be measured separately)

S & F Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

S&F in repair re-inforced punched concertina coil of 900 mm dia (chrome razer or blade wire) with barbed tape of 0.50 mm thick galvanised steel steel sheet or core wire of dia 2.5mm of high tensile steel wire including galvanised mild steel staple/clips for tying at crossing etc complete all as specified.

S&F in repair re-inforced punched concertina coil of 600 mm dia (chrome razer or blade wire) with barbed tape of 0.50 mm thick galvanised steel steel sheet or core wire of dia 2.5mm of high tensile steel wire including galvanised mild steel staple/clips for tying at crossing etc complete all as specified.

M/S RK Builders (BID ID -3298423)

KISHAN SINGH AND CO (BID ID -3303789)

M/s.sagar enterprises (BID ID -3298393)