SPECIAL REPAIR TO CERTAIN JCOs/OR MD ACCN OF BD BARI MIL STN UNDER GE KALUCHAK

Amount

Taking down cement plaster on bricks or stone wall/ decayed surfaces of concrete from roof projection or RCC Chajjas etc. including racking out joints, hacking for key, scrubbing down with water, etc including removing the waste out of defence land all complete all as specified and as directed.

Rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

M&L Rendering 15 mm thick on fair faces of brick/concrete surfaces in cement plaster 1:4 finished even and smooth without using extra cement, using water proofing compound mix as per manufacturer detail, complete all as specified and as directed.

Rendering 5 mm thick on concrete surfaces in CM 1:3 finished on even and smooth without using extra cement as in ceiling, Chajja etc. complete all as specified and as directed.

RCC chajja/fascia/parapet repair by using following steps :- (a) Removal of existing concrete along with loose damaged and cracked concrete/cover concrete from chajjas etc, exposing corroded steel reinforcements upto a depth of 10mm minimum behind the reinforcement by chipping/hacking with chisel and hammer or by mechanical means like chisel hammer, pneumatic chippers including high pressure water jetting to chipped concrete and reinforcement all as directed by Engineer-in-charge. Hard concrete shall not be removed. However if the rebar is corroded, concrete around it shall be removed. (b) Cleaning the surface of reinforcement bars from dust by using wire brushes and dry cloth and applying FOSROC Rebakleens RR- Rust Remover or equivalent using small brush and allow to react it for 16-24 hrs. (c) Providing and applying two coats of Fosroc Nitozinc Primer - two component, zinc rich epoxy, anti-corrosive protective coating or equivalent by brushes to the exposed and cleaned rebars with an interval of 45minutes to 1 hour @ 40microns DFT / coat and allowed to completely dry for 24 hours complete all as specified and as directed.

Supply only Integral water proofing compound liquid complete all as specified and as directed.

Taking down chowkats or frames n. exc. 1.5 sqm each but with shutter without taking off shutters from the frame complete all as specified and as directed.

Taking down chowkats or frames exceeding 1.5 sqm & not exceeding 4 sqm each but with shutter without taking off shutters from the frame complete all as specified and as directed.

Pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 125mm x 60 mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 Nos of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge complete all as specified and as directed.

Pressed steel frame for door with one or more rebates including necessary lugs, fixing lugs hinges, lock strike plate etc. of size 105mm x 60 mm and made of 1.25mm thick MS sheet, complete all as specified and directed including necessary welding complete and including medium weight 03 Nos of MS butt hinges of size 75mm / 100mm / 125mm and 01 No 50mm Size of medium weight MS butt hinge complete all as specified and as directed.

PCC (1:3:6) type C-2 (40 mm graded aggregate) filling back of chowkats complete all as specified and as directed.

35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with both face is covered with deco rative face veneer with lipping/frame to match complete all as specified and as directed.

35mm thick 2nd class hard wood Glazed and skeleton shutters open rebated & prepare to receive glass, gauge etc (without sash bars /edges of framing plain chamfered or rounded, fitted with cut and mitred beds for securing glass etc) size of members of shutters as spd in SSR Part-I section-8 clause 8.2 (A) complete all as specified and as directed.

Framed brackets of angles or tees with web and flanges cut to shape for cooler stand, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc. not exceeding 10 kg each brackets, conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Mild steel framed work as in doors ( as in chowkats)or gates of angle or other section with guest plates rails, braces rail etc exculsive of steel sheeting or other covering hanging also fastening and fixing complete confirming to Fe-410- W(Gde- E-250) quality- B including shop coat of red oxide including preparation of surface before fixing complete all as specified and as directed.

Factory made solid PVC moulded door shutter with wood free EPS 28 to 30mm thick (Stile) with flush panel with 2mm thick moulded PVC sheet on the front face & 2mm plain colour PVC sheet on back face complete all as specified and as directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, lugs as in hold fast with locking arrangements, complete all as specified and as directed.

Steel windows with side hung double shutters (window consisting of two shutters out side and two shutters of similar dimension inside of single MS Frame) box type hinges with steel handle of 100mm and steel peg stay, complete with glazing bars, and including MS guard bars and grills made out of 10mm MS square bar (Grill and guard bars shall be provided as per directions of Engr-in- Charge during execution of work) dovetailed or welded complete all as specified and as directed.

Galvanized mild steel wire cloth 0.45 nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tank or galvanized wire staple complete all as specified and as directed.

Sheet glass, ordinary quality, 3mm thick and glazed with oil putty or wooden beads, in square not exceeding. 0.5 Sqm each pane, complete all as specified and as directed.

3mm thick figured glass, pin head type and glazing with oil putty or wooden beads in square not exceeding 0.5 sqm each complete all as specified and as directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (both type) 300mm longh, and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Aluminium anodised 150mm long barrel tower bolt of extruded section and fixing complete all as specified and as directed.

Aluminium handles cast type anodised 150mm complete all as specified and as directed.

Butt hinges 100mm medium weight stainless steel complete all as specified and as directed.

Aluminium anodized barrel tower bolt of extruded section and fixed complete of size 125 mm long complete all as specified and as directed.

Aluminium handle cast type anodized of size 125mm complete all as specified and as directed.

Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel springs, fixed in floor with over all length of cover plate 150mm complete all as specified and as directed.d.

Dismantling floor, hearth or wall tiling , terrazzo topping on walls including cement mortar , bedding (but no backing) removing serviceable tiles and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed.

M&L for non skid coloured Ceramic tiles 7 to 8 mm thick in light shade (square/ rectangular) polished, area of each tiles exc 0.11 sqm but not exceeding 0.18 sqm, in floors/Skerting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm screed bed or beading layer in CM 1:4 complete all as specified and directed.

M&L for hard core, of broken bricks broken to gauge n exc 63mm for laying sub base of thickness 150mm complete all as specified and directed.

M&L Cement concrete type D-2 1:4:8 (40mm graded crushed stone aggregate) in foundations, filling and mass concrete in sub base complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B1 with 20mm graded aggregate for laying floor tiles complete all as specified and directed.

M&L for non skid coloured Ceramic tiles 8 to 10 mm thick in light shade (square/ rectangular) polished, area of each tiles exc 0.11 sqm but not exceeding 0.18 sqm, in floors/Skirting etc. set, jointed and pointed with Berger HS tile adhesive anti slip white @1.2kg/sqm thickness upto 8 to 10mm (or equivalent) and epoxy material for sealing of tile joints with Berger HS Epoxy tile grout(or equivalent) to the floor of toilets and bathroom complete all as specified and directed.

S&F 20mm dia High density polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 laid in as spout pipes to pour out rsidual water out from the treated area complete all as specified and directed.

M&L for non skid coloured Ceramic tiles 7 to 8 mm thick in light shade (square/ rectangular) polished, area of each tiles exc 0.11 sqm but not exceeding 0.18 sqm, in vertical surface such as skirting/dados etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick cement plaster in CM 1:4 complete all as specified and directed.

M&L Glazed ceramic coloured tiles 450x350mmx7mm thick for work vertical surfaces such as shirking/dado and risers to step etc set and jointed in neat slurry and pointed in white /coloured cement and pigment to match the tiles over and including 10mm thick cement plaster in CM 1:3 complete all as specified and directed.

M&L 18 to 20mm thick black Granite stone (table rubbed and polished) in cooking plateform bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone over 15mm thick screed bed in CM 1:4 after roughing surfaces of old concrete floor by picking sweeping down with water to remove dust etc including cutting holes into or through reinforced cement concrete slabs , for gas pipe (Superficial area wxc 100 sq cm but n. exc. 250 sq cm. complete all as specified and directed.

20mm dia PVC coated drapery rods in one length per door/window, fancy type (engraved rods), designed & coloured as approved by GE providing with two nos of Bracket powder coated for holding curtain rod and Fiber fancy dome type or wall to wall fixed in repair complete all as specified.

S&F 300mm ordinary rat tail mild steel rod pattern springs incl roller and roller plate complete all as specified and directed.

Dismantling water tanks exceeding 250 ltr capacity but not exc 500 ltrs complete all as specified and directed.

S&F Rotational molded polythene water storage tank vertical type with closed top hoisted and fixed in position all as spd in SSR part-I capacity 500 liters complete all as specified and directed.

S&F in repair 20 mm ball valves high pressure of PTMT with epoxy coated , aluminium rod & high density plastic ball screwed for iron pipe min wt 210 gms.

Taking up or down 15 mm steel tubing and connections including clearing for refixing or removal to store.

Taking up or down 20 mm steel tubing and connections including clearing for refixing or removal to store.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia15 mm, all as specified.

S&F Steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore dia 20 mm, all as specified.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from Serial here-in-before and fixed (walls, ceiling, floors, etc) of 15 mm dia complete all as specified and as directed.

Refixing old steel tubing and connections in new or old position with all fittings retrieved from Serial here-in-before and fixed (walls, ceiling, floors, etc) of 20 mm dia complete all as specified and as directed.

Demolition of cement concrete in and paving (un reinforced) exc. 15 cm. thickness, below or above ground level, including removal of waste from defence land and dumping at a place as specified by civil authorities complete all as specified

M&L for glass fibre reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent). Base coat: Berger HS Latex plus (or equivalent) Consumption base coat: 0.3 kg/m2 Reinforcement: Glass fiber Second and Third coat: Latex sheild 2K (or equivalent) Consumption top coat: 3 kg/m2 System requirements: density: 2.00 kg/ltr; compressive strength: 0.5 N/mm2. • Wall penetration through the RCC slab must be sealed using Berger HS RepirO(or equivalent). • Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus(or equivalent) modified mortar with a bonding coat of Berger HS Latexplus(or equivalent) modified cement slurry upto 5ft. • All depressions, unevenness, surface honeycombing shall be repaired using Berger HS Latex plus(or equivalent) modified polymer mortar with a bonding coat of Berger HS latex plus(or equivalent)modified cement slurry. Including cleaning of RCC surface to remove dust, loose particles, etc with compressed air or any other suitable technique depending on site conditions, grinding any sharp edges, etc

M&L rendering 10 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 with water proofing compound tobe finished even and smooth without using extra cement complete all as specified and as directed (WPC to be measured separately)

S&F Vitreous china water closet Orissa pattern long pan size 580x440mm with trap front or back inlet and integral foot rest complete fixed in repair including lime concrete bedding and connection to drain or outgoing pipe and to flushing pipe and anti siphon pipe complete all as specified and as directed.

S&F in repair Vitreous china wash down water closet pan (pedestal pattern), white including fixing bolt and flush pipe and PVC seat cover with necessary connection complete all as specified.

S&F PVC flushing cistern white shade low level 10 ltrs capacity, white with inlet ball valve, float and handle including bracket and flush pipe including connection to pipes, fixed in repairs complete all as specified and as directed.

S&F PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

Tubular towel rail, brass chromium plated, 20 mm dia, D type, 60 cm long between Hangs, fixed in repairs complete all as specified and directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brickets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as specified and directed.

S&F Stainless steel grating of 125mm size, male/female pattern with or without hole, fixed in nahani/floor traps with white/coloured cement, fixed in repairs, complete all as specified & directed.

PVC 32mm dia waste pipe with CP coupling, complete all as specified and directed.

S&F in repair Bib taps, chromium plated cast copper alloy, with capstan head, screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm, fixed in repairs, all as specified and as directed.

S&F in repairs Angle stop valve cast copper alloy, with fancy type chromium plated capstan head, screwed down, high pressure screwed both ends for 15 mm bore iron pipe or for unions and fixed complete, all as specified.

S&F in repair CP brass hot & cold 15mm dia wall mixture with provision for overhead shower with 115 mm long bend pipe on upper sie connecting legs & wall flanges for mixing hot & cold water complete all as specified and directed.

S&F in repair CP brass hot & cold 15mm dia 3 in1 wall mixture for kitchen & wall flanges for mixing hot & cold water complete all as specified and directed.

S&F in repairs Chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs 20 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed in repairs complete all as specified and directed.

Sheet glass shelf assembly consisting of 5,5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F 600x450mm PVC cabinet mirror of superior quality complete all as specified and directed.

Dismantling boarding any description fixed with screws complete all as specified and directed.

18/19mm thick Prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with screws to timber frame work as in cupboards , kitchen cabinat etc fixed in repairs complete all as specified and directed.

S&F Continuous (piano) hinges,width of flap when open is 30 mm mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F Magnetic catches of 25/30 mm size for cup Board shutter etc complete all as specified and directed.

S&F hasp and stapple, safety typeof Aluminium, anodised, including bolt to hinge type, fixed with screws of 100 mm complete all as specified.

TMT steel bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping to columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia, all as specified and directed.

TMT steel round bars 6 to 8mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping to columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia, all as specified and directed.

Form work to soffit of suspended slab such as roof slab not exc 20 0 mm thick horizontal or slopinf flate including fair finished to concrete surfaces complete all as specified and directed.

Form work to Edges of concrete flate floor and roof n.exc 20 cm wide and similar work exc 10 cm but not exc 20 cm wide rough finished to concrete surfaces complete all as specified and directed.

M&L RCC 1:2:4 Type B-1 (using 20 mm graded aggregate) in Roof slab, shelves supported on wall/column and the like etc complete as required.

Providing Precast cement concrete 1:2:4 Type B-1 (using 20 mm graded aggregate) in landings, cover slabs (for man holes etc) and the like etc complete as required.

Demolition of reinforced cement concrete ( reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of cement concrete in ground floors and paving (un reinforced) n exc. 15 cm. thickness, below or above ground level, complete all as specified.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for in plinth protection complete all as specified and directed.

75 mm thick PCC 1:3:6 type C-1, (using 20mm graded crushed stone aggregate) as in plinth protection finished even and smooth without using extra cement incl necessary joints complete all as specified and directed.

Dismantling cast iron or reinforced concrete drain pipes of 75/100mm bore, fixed with walls and taking out of trenches, if required all as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubbering joints fixed to walls 110mm bore complete all as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubbering joints fixed to walls 75 mm bore complete all as specified and directed.

S&F PVC (SWR) bends any radius 110mm bore with access door complete all as specified and directed.

PVC(SWR) junction single (single 'T') equal or unequal 110mm bore with access to door ccomplete all as specified and directed.

S&F PVC (SWR) bends any radius 75 mm bore with access door complete all as specified and directed.

PVC(SWR) junction single (single 'T') equal or unequal 75 mm bore with access to door ccomplete all as specified and directed.

M & L for PVC (SWR) multi floor trap diameter of outlet 75 mm with grating including jointing with solvent cement complete all as specified and directed.

S&F Plate rack made out of 1.00 mm thick stainless steel sheet of size 750mm x 750mm x250mm , complete all as sepcified and directed.

Preparation of new wooden surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

Preparation of old steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over red oxide primer, complete, all as specified and as directed.

M&L for two coats synthetic enamel paint over a coat of red oxide primer on newly steel surfaces complete all as specified and as directed.

Material and labour for preparation of newly plastered wall surface and applying two coat of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology, Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio as per manufacture's instruction and all coats incl primer to be applied with fully automatic airlessspray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI. Allow 6-8 hrs to dry the surface in subsequent coats of paint complete all as specified and directed Make: Berger Paints Weathercoat Long Life Flexo / Nerolac Paints excel Total / Asian Paint Apex Ultima Notes for smart periodicals item no 1 to 4: (a) Work shall be done as per MoU between tenderer and manufacturer of paints and their authorized applicator complete all as specified and directed (b) The contractor shall upload MoU between tenderer and manufacturer of paints and their authorized applicator before quoting the bids and submit the same alongwith tender & other Documents as mentioned in NIT. Make:- Asian Paint Ultima Protect/ Nerolac Excel Top Guard/ Berger Weather coat Long Life (c) Cost of scaffolding at any height shall be included in thequoted rate. (d) Preparation of plastered or unplastered surface or removal of existing treatment by scrapping of walls, chajjas, ceilings, fins, fascias, parapets etc shall be done by using mechanial sander with internal dust extraction system for clean environment certified by the manufacturer. After the prepartion of surface written approval shall be obtained from GE before applying primer and further treatment/coats. Bldg wise stage passing register shall be maintained. e) Finishes ie cement based paint, acrylic water based exterior grade primer, premium acrylic smooth exterior emulsion etc to walls, ceiling, chajjas, fins, fascias, parapets etc shall be applied using airless spray technology and capable of operating single spray gun with a suitable hose length. the spray machine should be of are putted manufacturer with pro-guard technology and capability of tracking pressure as well as paint and primer usage. (f) This equipment shall be certified by approved manufacturer. (g) The accessories for applying the finishes shall be spray in hard to reach areas and penetration of finishes on the surface so as to achieve uniform application and quality surface finish.

Material and labour for complete removal of existing treatment including fascias, cornices etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint and loose plaster to be completely removed by skilled labour and repair of external wall/Chajjas to be done with repair mortar to get even surface including preparation of old surface of wall/ceiling by filling cracks by Berger Bison Putty / crack fill paste of Berger Paints or equivalent make and make good smoothen surface by sand paper and applying two coats of premium acrylic smooth exterior emulsion of approved colour with silicon additive & Color stay Technology ,Excellent Dirt Pick up resistance of Berger Paints Ltd or equivalent of other approved make with low VOC less than 50 gram/ litre as per the LEEDS specifications, Anti Algal properties in two coats @ 1.79 ltr (undiluted)/ 10 sqm diluted with water as per manufacturer instructions applied over one coat of acrylic water based exterior grade primer @ 0.9ltr(undiluted)/10 sq mtrs diluted with water in 1:1ratio as per manufacture's instruction and all coats incl primer to be applied with fully automatic airless spray machine of paint application with a flow speed of minimum 1 ltr per minute having a pressure of 3300 PSI all as specified and directed. Allow 6-8 hrs to dry the surface in subsequent coats of paint and including necessary scaffolding at any height complete all as specified and directed Make: Berger Paints Weathercoat Long Life Flexo / Nerolac Paints excel Total / Asian Paint Apex Ultima

Complete removal of existing treatment from internal wall/ceiling surfaces including preparation of old surfaces and applying one coat of oil bound distemper over 3mm thick wall care putty complete all as specified and directed.

Preparation of new plastered surfaces and applying two coats of oil bound distemper on walls/Ceiling over 3 mm thick wall care putty complete all as specified and directed.

Demolition of brick work or stone masonary built in cement mortar including all quoins , arches, pillar etc but excluding ashlars facing dressed stone work and pre-cast concrete article complete all as specified and directed.

M&L Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6, complete, all as specified and as directed.

Brick work with sub class ‘B’ bricks ,straight or curved on plan exc 6 m mean radius and built in cement mortar 1:6 complete , but except bricks , i.e using serviceable bricks obtained from demolition complete all as specified and directed

Brick work in cement mortar 1: 4, using sub class ‘B’ bricks, straight or curved on plan any radius in half brick thick wall complete all as specified and directed.

M&L PCC 1:2:4 nominal mix type B-1 using 20mm graded crushed stone aggregate as in roof kerbs or mud stops etc rounded or chamfered on edges and the like including necessary form work complete all as specified.

M&L for capillary rise treatment of walls, Base coat: Berger HS Latex plus(or equivalent) Consumption base coat: 0.3 kg/m2 Second and Third coat: Latex sheild 2K(or equivalent) Consumption top coat: 3 kg/m2 System requirements: density: 2.00 kg/ltr; compressive strength: 0.5 N/mm2.

Complete removal of existing roof treatment or roof tile and removing from site to a place outside defence land as specified by civil authorities and clean the surface of roof with water and remove dust complete all as specified.

Cleaning of the exposed concrete slab and repairing the surface irregularities like cracks, potholes, as per manufacturers method statement by Berger HS Rapairo(or equivalent)along with HS Latex Plus(or equivalent)& cement in mixing ratio of 1:4 where ever required

M&L for HomeSheild PU Roofkoat(or equivalent)is a one component liquid ,solvent free ,cold applied , water-proofing membrane that is highly elastic and UV resistant with 10 years Warranty .ASTM D 6083-97a Waterproofing and heat reflecting systemhaving following key performance properties: 1.UV resistant ,prevent yellowing and weathering 2.Highly elastic upto 350% and crack bridging 3.Excellent adhesion on porous and non-porous substrates 4. Tensile Strength >10 N/mm2 with GeoTextile fleece 5. Soler Reflective Index (SRI) more then 109-111 ASTM E1980-11 System: First coat:Providing and applying primer over the prepared surface with HS PU roofkoat Primer(or equivalent) Coverage: 0.2kg/m2(with 50% dilution of water) Reinforcement: Geotextile 40 gsm Second coat:Home sheildroofkoat(or equivalent) Consumption: 0.5 kg/m2. Third coat: HS PU roofkoat(or equivalent) Consumption : 0.8 kg/m2. System buildup-1.5kg/sqm with geotextile of 40gsm For accessible roof, tiles with screed/ adhesive may be fixed thereafter.

Providing cement concrete type B-0 1:2:4 (using 12.5 mm graded stone aggregate ) in roof padding, roof kerbs or mud stops, rounded or chamfered on edges finished even and smooth without using extra cement complete all as specified and directed.

Dismantling and taking out damaged/corroded GI/CPVC pipe of size 20/25/40/50 mm bore all as specified and directed

Supplying and laying of CPVC pipes of dia 50 mm bore SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete fittings like socket, union, bend, elbow, tees etc complete all as specified and directed.

Supplying and laying of CPVC pipes of dia 25 mm bore SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete fittings like socket, union, bend, elbow, tees etc complete all as specified and directed.

Supplying and laying of CPVC pipes of dia 20 mm bore SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete fittings like socket, union, bend, elbow, tees etc complete all as specified and directed.

S&F 50 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for CPVC pipe and fixed complete all as specified and directed.

S&F 25 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for CPVC pipe and fixed complete all as specified and directed.

Cutting existing 80/100/150 mm GI pipe and inserting GI Tee of size 100x100x50 mm for tapping including necessary earth work and making flange for connection of new 50 mm of GI pipe including all as specified and directed by Engr-in-Charge.

Excavation in trenches, n. exc1.5 m wide and n. exc 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc. 10 sq m on plan and n. exc1.5 m in depth and getting out in soft / loose soil complete all as specified and as directed. Note : All excavation for taking out and re-laying of pipes shall be carried out mannualy and paid under this relevent item.

Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5m above from the starting point complete all as specified and as directed. (For Taking dwon Panel)

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified and as directed.

M&L under ground XLPE insulated, screened, PVC bedded galvanized steel strip or wire armored, electric power cable (heavy duty) with aluminium conductor, 1100 volts (earthed) grade cross sectional area 70 sqmm, 3.5 core laid in trenches/ pipes/ ducts/ wall/ boarings with necessary cable lugs and glands, nuts, bolts and washers etc and testing including disconnecting and taking out of existing LT cable of any type and size complete all as specified and directed. Note:- Excavation and earth, sand coushioning and protection for cable work shall be measured and paid separately.

Material and labour for sand cushioning for protection of underground cable consolidated and compacted with clean dry sand all as specified and as directed (Compacted thickness shall only be measured and paid)

Material and labour for well burnt bricks,Sub class 'B' bricks, best quality locally available laid flat, dry in trenches for cable protection complete all as specified and as directed

Laying only old brick dry in trenches for cable protection retrieved from site complete all as specified and as directed

M&L for GI pipe 50 mm dia "light grade" ISI marked, laid in trenches/ on floors/on, pole/road for cable protection including necessary joints / fittings including taking up / down and removing old unserviceable GI pipe complete all as specified and directed .

Taking out carefully copper/aluminium point wiring,Light,fan,socket or power complete with all fitting, fixtures such as switch socket out let, ceiling rose ,holder ,regulator,DBs etc including making good the disturbed surface of wall/floors complete.

Taking down distribution boards/wooden board ,switch fuse units,steel enclosures for MCB of any type and removing from site all as specified and as directed by the Engineer in charge.

Taking down ceilling fan/exhaust fans and deposite to MES store yard from site all as specified and as directed by the Engineer in charge.

Taking down Geyser any cap and deposite to MES store yard from site all as specified and as directed by the Engineer in charge.

Taking down existing unserviceable submain wiring any size and making good the disturbed surface all as specified and as directed.

Material and labour for point wiring for one light controlled by one way switch with 1.5 Sqmm PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable 1100 Volts grade drawn through and including rigid non metallic PVC concealed conduit (medium grade) of suitable dia along with 1.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire, connected to earth dolly and to be terminated in and including pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type for mounting of modular switches, sockets, fan regulators alongwith modular plate etc including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good disturbed surface all as specified and as directed.

All as per item No 133 above but for one fan point controlled by one piano switch all as specified and as directed.

All as per item No 133 above but One light point controlled by two way switch

All as per item no-133 above but for one bell point controled by one bell push all as specified and as directed.

All as per ser item No 133 hereinbefore but for one 3 pin socket outlet 5 Amp Same board.

All as per ser item No 133 hereinbefore but for one 3 pin socket outlet 5 Amp independent.

All as per Item no 133 here-in-before but for one15 Amp 3pin switch socket outlet, independent with 2.5 Sqmm single core multi-stranded copper conductor cable (FRLS) along with 2.5 sqmm continuous PVC insulated unsheathed single core multi-stranded copper conductor (FRLS) cable for earth continuity wire all as specified and as directed.

Supply and fix modular type switch, one way 6 Amps , 1 module complete all as specified and directed.

Supply and fix modular type switch, Two way 6 Amps , 1 module complete all as specified and directed.

Supply and fix modular type switch, one way 16 Amps, 1 module complete all as specified and directed.

Supply and fix modular type socket 5 pin, 6 Amps 2 module complete all as specified and directed.

Supply and fix modular type socket 5 pin, 6 A/16 Amps 2 module complete all as specified and directed.

Supply and fixing of Ceiling rose surface bakelite three terminals 240 volts complete, all as specified.

Supply and fixing Lamp holder PVC case body of Bakelite with back plate suitable for batten fittings , all as specified.

S&F LED Bulb cool white 10 Watt Elegant design direct fit for easy installation all as specified and directed.

Supply and fixing Bell push flush type piano 5 Amp complete, all as specified.

Supply and fixing Bell multi music 230 volt ,AC single pole complete all as specified.

Supply and fixing of Tube light fitting integrated type suitable for LED 20W indoor decorative aluminium extruded LED batten complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting complete all as specified and directed.

Supply and fixing of Tube light fitting integrated type suitable for LED 10W indoor decorative aluminium extruded T5 LED batten complete with hosing with all accessories pre wired and making connection with three core copper flexible cable of size 23/0.0076 from ceiling rose to PVC connection to light fitting complete all as specified and directed.

Supply and fix in repairs factory made epoxy powder coated Distribution board VTPN 6 ways ,415 Volts with metal door (IP-54 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 100 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cale management, top and bottom removable gland plates with Knockouts and suitable for one MCCB as incommer and SP MCBs outgoing complete all as specified and confirming to IS : 8623.

Supply and fixing factory made epoxy powder coated Distribution board SPN 12 ways (SPN MCB DB) with metal door (IP-54 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 100 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cale management, top and bottom removable gland plates with Knockouts and suitable for one SPN/DP-MCB as incomer and SP MCBs outgoing complete all as specified and confirming to IS : 8623.

Supply and fixing MCB SP-06 to 32 Amp,10KA, 240 volts complete all as specified.

Supply and fixing of MCB SPN 32 Amp, 240 volts 50Hz AC supply, complete all specified.

S&F in repair MCCB 415 Volt16 KA 4 Pole 125 Amps all as specified and directed.

S&F single core PVC insulated unsheathed multistanded copper conductor cable 1 Sqmm , 1100 Volts ISI marked drawn through existing conduite.

Material and labour for sub main wiring with two single core PVC insulated (unsheathed) multi strand copper conductor FRLS cable of size 6 sqmm and one single core PVC insulated (unsheathed) solid copper conductor FRLS cable of size 6 sqmm as in continuous earth wire drawn into and including concealed PVC conduit medium grade 25mm dia ISI marked complete with fittings and fixings accessories complete and including cutting chases pinning in making good to facing and pointing in using cement moter 1:3 and making good disturbed surface complete all as specified and as directed.

M & L for earthing complete with galvanized steel earth plate 600x600x6mm thick buried vertically in ground to depth not less than 2.25 mtr below ground level, with top edge of the plate not less than 1.50 mtr below normal ground level, connected to GI earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and connection to main switch board of panel, including watering pipe GI 20 mm bore light grade 15mm bore for earthing lead, wire mess, funnel, salt, charcoal dust, excavation and refilling pit with PCC 1:2:4 type B1(using 20mm dia stone aggregate) reinforced with 6mm dia round bar @ 75mm cement concrete both always with MS handle 12mm dia and frame all as shown in electric plate No 3 in page 497 of SSR Part I (2009) and pouring extra Clay Soil of qty not less than one cubic meter into the earth pit and also removal of excavated soil not less than 50 mtr from the earthing place all as specified and directed and tested on completion. including testingall as specified and directed by E-in-Charge.

Supply and fixing LED Bldg security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with suitable size and length of 1.5 sqmm copper conductor with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

S & F LED light fitting 1x9W/1X10Wbulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

Fixing only exhaust fans complete with blades, and accessories obtained vide srl Item No- 130 above with provision of new Anti suicide Fan Rod (suitable size and length and oiling/greasing of fan with provision of flexiable cable twin core all as reqd at site. all as specified and directed by Engr-in-Charge.

M&L for cutting of suitable size of holes for 300 mm exhaust fan in wall and grouting of nuts and bolts in wall and making good to match with existing walls all as specified and directed by Engr-in-Charge.

Taking down electric energy meter single phase any size or type form the existing site and refixing the same at same place after carrying out necessary repair work in building and making the surface good to match with existing surface all as specified and directed by Engr-in-Charge.

Fixing only ceiling fans complete with blades, and accessories obtained vide srl Item No-130 above with provision of new Anti suicide Fan Rod (suitable size and length and oiling/greasing of fan with provision of flexiable cable twin core all as reqd at site. all as specified and directed by Engr-in-Charge.

Fixing only electric water heater, geyser storage type obtained vide srl Item No- 131 complete with provision of fixing Nut bolts as required at site all as specified and directed by Engr-in-Charge .

Supply and fixing 3 pin 15/16 Amp plug top suitable for 240V 50Hz AC supply all as specified and directed.

GANDOTRA CONSTRUCTION CO (BID ID -3390186)

M/S ARUN ANAND (BID ID -3382496)

M/s Khajuria Construction Co. (BID ID -3381384)

bamral builder (BID ID -3389258)

NARESH KUMAR AND COMPANY (BID ID -3389932)

M/S VED PAUL MAHAJAN (BID ID -3381305)

Sarbat Construction Co (BID ID -3389417)

GENESIS INDIA (BID ID -3389199)