CERTAIN SANCTIONED SPECIAL REPAIR, REVENUE WORKS AND MINOR WORKS AT MIRAN SAHIB UNDER GE JAMMU

Amount

B/R Portion: - Dismantling wall and ceiling boards (fibre, pulp, insulation etc), or insulation boards / slabs / blankets, any thickness any type including cover fillets complete all as specified and as directed.

Dismantling wrought iron or mild steel work as in wind tie, grill grating, cooler stand etc complete all as specified and as directed.

Dismantling unframed work timber scantling 40 Sqcm and over in section in any position as in unframed work complete all as specified and as directed.

Dismantling timber scantling in fillets, posts, rafters, purlins etc under 40 Sqcm in section complete all as specified and as directed.

Dismantling AC corrugated, semi corrugated sheets in roof covering including ridge complete all as specified and directed.

Supply and fixing pre-painted galvalume aluminium zinc coating galvanised iron based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPA as in roof covering fixed with self tapping screws or L-type or J-type or cranked hook bolts complete all as specified and directed.

Supply and fixing pre-painted galvalume aluminium zinc coating galvanised iron based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 MPA as in ridge of roof fixed with self tapping screws or L-type or J-type or cranked hook bolts complete all as specified and directed.

Taking down chowkhats or frames not exceeding 1.5 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc. including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Material and labour for 10 mm thick rendering in cement mortar (1:6) on other than fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for rendering 15mm thick on fair faces of brick / concrete surfaces with water proofing compound built in cement mortar (1:4) finished even and smooth without using extra cement complete all as specified and as directed. Note: - Water proofing compound shall be measured and paid separately.

Material and labour for preparation of new surface and applying two coats of oil bound distemper on new plastered surfaces over 1 mm thick putty complete all as specified and directed.

Material and labour for complete removal of existing surface and preparation of old surface and applying two coats of oil bound distemper over 1 mm thick putty complete all as specitied and directed.

Material and labour for preparation of new surface and applying two coats of exterior emulsion / weather proof paint over a coat of primer over and including 1mm thick putty on plastered surface complete all as specified and directed.

Material and labour for complete removal of existing surface and preparation of old surface and applying two coats of exterior emulsion / weather proof paint over a coat of primer over and including 1mm thick putty on plastered surface complete all as specified and directed.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

Material and labour for factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the mild steel frame welded / sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification complete all as specified and directed.

Supply and fixing 35 mm thick plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned complete all as specified and directed.

Supply and fixing 35mm thick second class hard wood factory made glazed and skeleton shutters, open, rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc.; sizes of members of shutters as specified in SSR Part - I, Section 8, clause 8.20 (a) complete all as specified and directed.

Supply and fixing pressed steel frames (factory made) made out of 1.25 mm thick black mild steel sheet for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., complete size of frame 105 x 60mm including bottom of each chowkhat to be welded with 2 No's 25 x 25 x 3mm thick flat iron projecting 10 cm on either side complete all as specified and directed.

Description all as per Ser Item No. 21.00 here-in-before but size of frame 125 X 60mm for fixing of two shutters complete all as specified and directed.

Supply and fixing structural steel / tubular section work as in roof trusses (framed), post, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections or mild steel tube pipe) including distance pieces, cleats etc Fe-410W (Grade 'E'-250) quality 'A' including shop coat of primer complete all as specified and directed.

Supply and fixing steel work in tubular / rounded trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St.-240 including shop coat of primer complete all as specified and directed.

Material and labour for plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment as in gusset plate, base plate etc complete all as specified and directed.

Supply and fixing mild steel bolts purpose made with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut exceeding 30cm long (dia of neck exceeding 12 but not exceeding 20 mm) complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Material and labour for reinforced cement concrete (nominal mix) (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Material and labour for formwork to flat soffits of suspended slabs such as roof slabs, floor slabs, landings as in shelves and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished complete all as specified and directed.

Material and labour for mild steel TMT bars 10 mm dia and over cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips conforming TMT bar complete all as specified and as directed.

Description all as per Ser item No 30.00 here-in-before but 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders etc complete all as specified and as directed.

Material and labour for RCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in cement concrete in PCC band and lintel band, in lintels upto 1.5m clear span and other similar bands, plinth courses complete all as specified and directed.

Material and labour for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC / PCC bends in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide complete all as specified and directed.

Supply and fixing mild steel framed works such as grills, framed guard bars, etc and similar work as in cooler stands etc. conforming to Fe-290 Grade 'E' 165 complete all as specified and directed.

Material and labour for PCC (1:3:6) type C-0 (using 12.5 mm graded crushed stone aggregate) as in back filling, bed block for hold fast etc complete all as specified and directed.

Material and labour for PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in coping, benching on corner of joints, as in roof kerbs or mud stops rounded or chamfered on edges and benching of manholes and including necessary formwork etc complete all as specified and directed.

Supply and fixing 100 mm size butt hinges medium weight cold rolled stainless steel complete all as specified and directed.

Supply and fixing aluminium handles 'D' type anodised 150 mm long ISI marked complete all as specified and directed.

Supply and fixing aluminium handles 'D' type anodised 125 mm long ISI marked complete all as specified and directed.

Supply and fixing 200 mm long aluminium anodised barrel tower bolt of extruded section ISI marked complete all as specified and directed.

Supply and fixing 150 mm long aluminium anodised barrel tower bolt of extruded section ISI marked complete all as specified and directed.

Supply and fixing 300 mm long dia 16mm aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and directed.

Supply and fixing mild steel enamelled helical door spring 150 mm (ISI marked) size including roller and roller plate, fixed to wooden / steel frames by any means as required complete all as specified and directed by Engineer-in-Charge.

Supply and fixing floor door stopper of aluminium alloy body and tongue 140 mm anodised with hard drawn steel spring fixed in floor complete all as specified and directed.

Supply and fixing galvanised mild steel wire cloth 0.56 mm nominal dia or wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

Material and labour for preparing surface of new wood and wood based material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and labour for preparing surface of new steel material of any description and girth, not otherwise described and treated with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material and labour for providing and fixing in position suspended false ceiling system using 'E' grid suspended ceiling grid system. The size of grid shall be 600 X 600mm with GI frame work, main runner 39 X 24mm, cross tee 29 X 24mm and wall angle 22.2 X 22.2mm using 4mm thick high pressure stream cured non primered classic / designer variant E-Board ISI Marked IS No : 14862-2000. Fibre cement 'E' board to be placed in the grid of 'E' grid suspended ceiling grid system duly suspended by 4mm dia GI bar hangers from the purlins of the roof with butterfly clips including dismantling wall and ceiling boards (fibre pulp / insulation) any thickness including cover fillets including taking down all electric fittings fixed with ceiling and refixing the same in position after replacing the ceiling complete all as specified and directed.

Demolition of concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Material and labour for 25 mm thick PCC (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate), as in sub base complete all as specified and directed.

Material and labour for vitrified coloured ceramic tiles 10mm thick (square / rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in cement mortar (1:6) complete all as specified and as directed.

Material and labour for vitrified coloured ceramic tiles 10mm thick (square / rectangular) polished, area of each tiles not exceeding 0.36 Sqm, in dado / skirting / vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick rendering in cement mortar (1:4) complete all as specified and as directed.

Material and labour for non skid ceramic colour tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm screed bed in cement mortar (1:6) complete all as specified and directed.

Material and labour for glazed ceramic colour tiles (450 X 350 mm) X 7mm thick as in dados, skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering cement mortar (1:6) complete all as specified and directed.

Material and labour for 16 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills cooking platforms and like in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite including taking down old complete all as specified and directed.

Material and labour for providing edge moulding to 18-20mm thick granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed.

Dismantling stone slabs laid dry and tiles of any description or thickness in floors, aprons etc. and rubbish off the premises complete all as specified and as directed.

Material and labour for machine cut kota stone slab flooring 18-20mm thick as in floor to match the shade of the slab including 20mm screed bed in cement mortar (1:6) including rubbing, polishing complete all as specified and directed.

Material and labour for machine cut kota stone slab flooring 18-20mm thick as in riser in step, skirting / dado to macth the shade of the slab including rubbing and polishing over and including 10mm rendering in cement mortar (1:4) complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

Dismantling water tanks exceeding 500 and not exceeding 1000 litres complete all as specified and directed.

Supply and fixing 1000 litre capacity rotational moulded polyethylene water storage tank (cylindrical vertical with closed top) five layers hoisted and fixed in position complete all as specified and directed.

Supply and fixing in repair vitreous china squatting pan 'Orissa' pattern, size 580 x 440 mm white, with integral foot rest and 'P' or 'S' trap and connection to flushing pipe, anti-syphonage pipe complete including provision of cement concrete bedding complete all specified in SSR part - I and as directed.

Supply and fixing in repair vitreous china wash basin, white, flat back, size 550 x 400 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, waste coupling cutting, waste pipe for and pinning in ends of brackets or erecting stand complete all as specified and directed.

Supply and fixing in repair vitreous china white under counter wash basins (595 x 420 x 200 mm) oval shape, including waste pipe, brackets and connecting pipe fixed complete all as specified and directed.

Supply and fixing in repair PVC valveless, symphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

Supply and fixing in repair low density PVC connections commercial quality 15mm bore with PTMT nuts of length 450mm complete all as specified and directed.

Supply and fixing in repair low density PVC waste pipe 32 mm bore for flushing cistern complete all as specified and directed.

Supply and fixing in repair 15 mm bore bib taps long nose / long body, cast copper alloy chromium plated fancy type with capstan head handle screwed down, screwed for brass, weight not less than 450 grams ferrule and fixed complete all as specified and directed.

Supply and fixing in repair 15 mm bore angle valves, cast copper alloy chromium plated fancy type, half turn, screwed down, high pressure, with crutch or butterfly handle, weight not less than 450 grams screwed both ends for iron pipe or for unions complete all as specified and directed.

Supply and fixing in repair 15mm dia chromium plated pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot or Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

Supply and fixing in repair 15 mm bore sawn neck pillar cock cast copper alloy, chromium plated with angular knob fixed to 15mm dia mild steel pipe complete with all fittings all as specified and directed.

Supply and fixing in repairs shower rose brass chromium plated with swivel joint of size 125 mm cast copper alloy chromium plated fancy type with chromium plated neck 9" long made to shape, weight not less than 350 grams complete all as specified and directed.

Supply and fixing in repairs 20 mm dia gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Taking down eaves, gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

Supply and fixing in repair PVC (SWR) bends 110 mm radius complete all as specified and directed.

Supply and fixing in repair 110 mm PVC (SWR) junction single (T) equal / unequal complete all as specified and directed.

Supply and fixing in repair PVC (SWR) bends / shoes any radius of 75 mm dia complete all as specified and directed.

Supply and fixing in repair PVC (SWR) bends any radius provided with access door of 110mm dia complete all as specified and directed.

Supply and fixing in repair PVC (SWR) bends any radius provided with access door of 75mm dia complete all as specified and directed.

Supply and fixing in repair PVC (SWR) vent cowl of radius of 75 mm dia complete all as specified and directed.

Supply and fixing in repair 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete B-1 (1:2:4) complete all as specified and directed.

Supply and fixing in repair brass chromium plated towel rail 20 mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

Supply and fixing in repair mild steel peg set of six power coated as approved by GE complete all as specified and directed.

Supply and fixing in repair drapery curtain rod of metallic 20mm / 25mm dia covered with PVC coating including mild steel bracket, end ball, rounded block (coated with brown / cherry / golden colour) of approved pattern and shade fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screws complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

Material and labour for 75mm thick cement concrete (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) as in floor / plinth protection laid in suitable panels finished even and fair. 6mm joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 85/25 or 80/100 grade and three parts of sand (all by weight) complete all as specified and directed.

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, drains etc, but excluding ashlars facings, dressed stone work and precast concrete articles complete all as specified and directed.

Material and labour for brick work with sub class ‘B’ bricks straight or curved on plan exceeding 6m mean radius built in cement mortar (1:6) complete all as specified and directed.

Material and labour for brick work with sub class 'B' bricks straight or curved on plan to any radius in half brick thick wall in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge.

Supply and laying vitreous china urinals, flat back size of 465 x 355 x 265 mm white with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe, brackets and chromium plated waste coupling including urinal spreader complete all as specified and directed.

Material and labour for cement concrete type (1:3:6) C-2 (using 40 mm graded crushed stone aggregate) as in surface channels complete all as specified and directed.

Material and labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement complete all as specified and directed.

Supply and fixing in repair 125 mm chromium plated stainless steel grating with or without waste hole complete all as specified and directed.

Material and labour for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster (1:4) (1 cement : 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per Square metre, top layer 15mm cement plaster (1 : ½ : 2) (1 cement : ½ coarse sand : 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing the top layer with brushes and water to expose the stone chippings complete all as specified including taking down old plaster and two coats of cement based paint all as directed.

Supply and fixing in repair sinks with drainage board made of stainless steel 1 mm thick in kitchen with plugs, washers and waste coupling, waste pipe, including bedding in cement mortar on wall including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460 mm, bowl size 410mm x 330mm x 160 mm complete all as specified and directed.

Supply and fixing in repair soap dish steel chromium plated 100 mm size complete all as specified and directed.

Supply and fixing box type steel windows / ventilator (factory made) outer frame made out of ERW tube 'P' section 65 X 45 X 25 mm and shutter of ERW tube 'P' section 50mmX35mmX20mm openable (double shutter) with glazed shutter on external side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 no's on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler / AC window and shown on drawings No CEPZTD-324/07 Sh 1/3 to 3/3 complete all as specified and directed. Notes: - The quoted rates shall also include: - (i) One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrete surface. (ii) 4 no's MS steel lugs made of 20 X 5 mm iron flat 200 mm long. (iii) 10 mm Sq Bar grill / guard bar design as per drawing. (iv) PCC block for embedding lugs. (v) Two coats of synthetic enamel paint. (vi) Galvanised mild steel wire cloth 0.56 mm nominal dia or wire and average width of aperture 1.0 mm and fixed with tinned tacks or galvanised wire staple complete all as specified and directed.

Supply and fixing 3mm thick sheet glass, ordinary quality glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

Supply and fixing in repair powder coated aluminium three track sliding type glazed window, shutter with 5mm thick plain sheet glass fixed open track section 100 x 38 x 1.4 mm having three track (two of 5.50 mm thick glass and one of stainless steel wire cloth of 0.56 mm dia and 1.18 mm aperture) with members of window shutters of section 38 x 12mm including aluminium grill 75 mm x 5.50 mm thick pitch diamond shape, wire gauge and grill shall be fixed with the help of 40 mm aluminium flat and other standard Bombay sliding section including all necessary fiber wheel rollers suitable handle to facilitate sliding and all necessary jointing cleats, glazing clips, rubber packing, aluminium snap beading etc complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out any type of soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc, for laying of drain pipes, or for shafts, wells cesspits, pier holes etc and for manhole etc, not exceeding 10 Sqm on plan and not exceeding 1.5m in depth and getting out in any type of soil complete all as specified and as directed.

Material and labour for PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in mass concrete, in foundation complete all as specified and as directed.

Material and labour for brick work with fly ash brick (old size brick), straight or curved on plan exceeding 6 m mean radius built in cement mortar (1:6) complete all as specified and as directed.

Material and labour for hardcore of gauge of broken stone or boulders not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

Material and labour for 75 mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) in floor as sub base complete all as specified and as directed.

Material and labour for rendering 5mm thick in cement mortar (1:3) finished even and smooth on cement concrete surfaces as in ceiling complete all as specified and as directed.

Material and labour for provision of roof treatment with polymeric water proofing membrane all as given below: - (a) Material and labour for plastering 10mm thick in cement mortar (1:3) using 100% coarse sand on roof surface including water proofing compound as per manufacturer's instructions and as directed by Engineer-in-Charge. (b) Applying a coat of bituminous primer conforming to IS : 3384-1986 @ 0.25 Iitres/sqm on prepared surface and allowed to dry. (c) Applying and laying 3mm thick APP membrane having non woven polyester matt at core and covered with high quality polymeric asphaltic protected thermo fusible HMHDPE film on both sides with over laps 10cm and 15 cm at longitudinal and transverse direction respectively and sealed by flame, sealing all overlaps complete including treatment at all junctions and corners. The membrane shall be torched into groove on vertical plane and groove sealed with cement mortar (1:3). (d) Material and labour for two coats of aluminium paint on membrane surface 1338.40 complete all as specified and as directed.

Supply and fixing 15 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and as directed.

Supply and fixing 20 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and as directed.

Supply and fixing 25 mm dia galvanized pipes medium grade with all fittings and fixed complete wall and ceiling or laid in floors complete all as specified and as directed.

Supply and fixing rotational moulded polyethylene water tank (cylindrical vertical closed top) hoisted and fixed in position capacity of tank 1000 litres and supply and fixing ball brass valve high pressure with polythene float and fly nut complete 20mm bore screwed to pipe for brass complete all as specified and as directed.

Material and labour for preparing plastered surface and applying three coats of white wash on wall complete all as specified and as directed.

Material and labour for preparing plastered surface and applying three coats of white wash on ceiling complete all as specified and as directed.

Material and labour for preparing plastered surface and applying two coats of cement based paint on wall over a coat of primer complete all as specified and as directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in each layers hard / dense soil complete all as specified and as directed.

Removing excavated materials in soil to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.50m above the starting point complete all as specified and as directed.

Supply and fixing vitreous china water closet pedestal pattern with seat cover white including pedestal pan and trap, connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe etc complete all as specified and as directed.

Supply and fixing vitreous china white under counter wash basins (595 x 420 x 200 mm) oval shape including waste pipe, brackets and connecting pipe fixed complete all as specified and as directed.

Supply and fixing PVC valveless, symphonic action type, flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

Supply and fixing chromium plated jet spray with flexible pipe not less than 90 cm long fixed to EWC suitable for 15mm bore complete all as specified and as directed.

Supply and fixing health faucet (hand shower) with 1 metre flexible tube with hot and cold water supply wall hook, bracket etc complete set of superior quality complete all as specified and as directed.

Supply and fixing brass chromium plated towel rail 20 mm dia 'D' type 60 cm long between flanges complete all as specified and as directed.

Supply and fixing low density PVC connections commercial quality 15mm bore with PTMT nuts of length 450mm complete all as specified and as directed.

Supply and fixing low density PVC waste pipe 32 mm bore for flushing cistern complete all as specified and as directed.

Supply and fixing 15 mm bore bib taps long nose / long body, cast copper alloy chromium plated fancy type with capstan head handle screwed down, screwed for brass, weight not less than 450 grams ferrule and fixed complete all as specified and as directed.

Supply and fixing 15 mm bore angle valves, cast copper alloy chromium plated fancy type, half turn, screwed down, high pressure, with crutch or butterfly handle, weight not less than 450 grams screwed both ends for iron pipe or for unions complete all as specified and as directed.

Supply and fixing 15 mm bore sawn neck pillar cock cast copper alloy, chromium plated with angular knob fixed to 15mm dia mild steel pipe complete with all fittings complete all as specified and as directed.

Supply and fixing 20 mm dia gun metal, globe or gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

Supply and fixing 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees complete fixed to walls at any height complete all as specified and as directed.

Supply and fixing 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees laid in trenches or in floors complete all as specified and as directed.

Supply and fixing 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, bends, Tees laid in trenches or in floors complete all as specified and as directed.

Supply and fixing PVC (SWR) bends 110 mm radius complete all as specified and as directed.

Supply and fixing 110 mm PVC (SWR) junction single (T) equal / unequal complete all as specified and as directed.

Supply and fixing 75 mm PVC (SWR) junction single (T) equal / unequal complete all as specified and as directed.

Supply and fixing PVC (SWR) bends / shoes any radius of 75 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) bends any radius provided with access door of 110mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) bends any radius provided with access door of 75mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) vent cowl of radius of 75 mm dia complete all as specified and as directed.

Supply and fixing 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 complete all as specified and as directed.

Supply and fixing stack clamps made out of 50mm x 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stay to walls or roof for 75 mm bore pipe complete all as specified and as directed.

Material and labour for galvanised iron spout 25mm dia light grade, fixed to walls complete all as specified and as directed.

Material and labour for cutting openings through brick walls for door, window and other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective brick work for under-pinning including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc. to store and rubbish not exceeding 50m complete all as specified and as directed.

Material and labour for forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, cememt mortar (1:4) complete all as specified and as directed.

Supply and fixing glass corner shelf, fancy type, 250 x 250 and 10mm thick fixed with brass bracket and screwed complete all as specified and as directed.

Supply and fixing glass shelf rectangular size 450mm x 150mm, 5 mm thick glass with stainless steel bracket complete all as specified and as directed.

Supply and fixing 150 mm toilet paper holder with flat recessed type stainless steel complete all as specified and as directed.

Material and labour for cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exceeding 10 cm girth complete all as specified and as directed.

Material and labour for brick work with fly ash bricks, straight or curved on plan to any radius in half brick wall built in cement mortar (1:4) complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) in foundation of manholes complete all as specified and as directed.

Material and labour for concrete bed to 150 mm bore pipe (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) including haunching against the sides of pipe complete all as specified and as directed.

Supply and fixing and laying 150 mm thick reinforced concrete pipes class NP-2 laid and jointed complete with collars as in trenches complete all as specified and as directed.

Material and labour for RCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) in precast manhole cover and cover slab for septic tanks and including necessary forms and moulds etc and set in cement mortar (1:4) complete all as specified and as directed.

Material and labour for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or 3/4 section) in cement concrete (1:2:4) type B-1 smooth finished and reforming benching as required of 150mm dia pipe complete all as specified and as directed.

Material and labour for construction of septic tank for 10 users capacity including excavation and earth work in ordinary soil, foundation with PCC (1:2:4) type B-1, brickwork in cement mortar (1:4), RCC (1:2:4) type B-1 slab, RCC precast manhole cover having 6mm plate embedded around with angle iron frame, vent shaft and sludge chambers etc all as shown on drawing no. CEPZ/C-TD-013-13 complete all as specified and as directed. Note: - Rate quoted includes final depth of Invert level of septic tank on the basis of longitudinal slope of sewage line.

Material and labour for construction of soakage well 1.20 m dia and 3.0 m (effective depth) deep excavation in any type of soil foundation in PCC (1:3:6) walls of honey combed brick work with top ring of M-25 concrete including intercepting chamber and screen chamber made of brick work in cement mortar, RCC cover slab M-25 / SFRC cover interconnecting pipes of RCC / DEC complete filled with brick bats as shown on drawing no. CEPZ/C-TD-013-13 complete all as specified and as directed.

Material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design and pattern as in footpath, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness and size / shape, made by table vibratory method using PU mould, laid in required colour and pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of interlocking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

Material and labour for excavating in post holes (or for similar work) each not exceeding 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard / dense soil complete all as specified and as directed.

Material and labour for cement concrete (1:2:4) type B-2 (using 40mm graded crushed stone aggregate) in foundations, filling and mass concrete complete all as specified and as directed.

Material and labour for cement concrete (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in coping of drains complete all as specified and as directed.

Supply and fixing coloured 10 mm thick twin wall polycarbonate sheet, weight not less than 1.7kg/sqm, U value 2.9, tensile strength not less than 62 MPA, fixed to steel frame work in steel frame work in roof with self tapping screw and aluminium 'H' clamp with EPDM sealings on both sides to prevent leakage complete all as specified and as directed by Engineer-in-Charge or manufacturer's instructions.

Supply and fixing vitreous china squatting pan 'Orissa' pattern, size 580 x 440 mm white, with integral foot rest and 'P' or 'S' trap and connection to flushing pipe, anti-syphonage pipe complete including provision of cement concrete bedding complete all specified in SSR part - I and as directed.

Supply and fixing vitreous china wash basin, white, flat back, size 550 x 400 mm excluding taps, waste, chain and plug and porcelain stopper but including brackets, waste coupling cutting, waste pipe for and pinning in ends of brackets or erecting stand complete all as specified and as directed.

Supply and fixing 15mm dia chromium plated pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

Supply and fixing 125 mm chromium plated stainless steel grating with or without waste hole complete all as specified and as directed.

E/M Portion: - Taking down old unserviceable copper / aluminium point wiring concealed / batten (light, fan, socket or power) complete, including fixture and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type of switch board wooden / iron, round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Material and labour for sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 6 Sqmm for phase and neutral and one run of 6.0 Sqmm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase / neutral and one run of cable for earth will be measured and paid as one unit length including taking down old wiring complete all as specified and directed. Note: - Wiring shall be done in proper colour coding.

Material and labour for complete point wiring with 1.5 Sqmm single core multistranded copper conductor FRLS insulated and sheathed heavy duty cable in colour code including continuous earth wire with cable of size 1.5 Sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall, plastering after concealing conduit including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc and including making good the disturbed surface as per existing complete all as specified and as directed by Engineer-in-Charge for the following: -

Description all as per Ser item No 172.00 here-in-before but for multi 5 pin 5 amp socket outlet on same board complete all as specified and directed.

Description all as per Ser item No 172.00 here-in-before but for multi 3 pin socket outlet 5 amp socket on independent board complete all as specified and directed.

Description all as per Ser item No 172.00 here-in-before but for multi 3 pin 15 Amp socket outlet independent controlled by 15 Amp switch with 2.5 Sqmm copper conductor multistranded cable PVC insulated FRLS and unsheathed cable in and including PVC rigid concealed conduit 20/25 mm dia and unsheathed copper conductor multistranded cable 2.5 Sqmm as earth wire FRLS PVC insulated in green color complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair modular switch 1 way 6A, 1 module, 240 volts ISI marked complete all as specified and directed.

Supply and fixing in repair modular socket, 6 A - 5 pin combined 2 module, 240 volts ISI marked complete all as specified and directed.

Supply and fixing in repair modular switch 1 way 16A, 1 module , 240 volts ISI marked complete all as specified and directed.

Supply and fixing in repair modular socket 6A/16A - 6 pin combined 2 module, 240 volts ISI marked complete all as specified and directed.

Supply and fixing in repair ceiling rose, 3 phase / PVC / polycarbonate isolated body complete all as specified and directed.

Material and labour for fan regulator stepped electronic type suitable for AC, 240 V complete all as specified and directed.

Material and labour in replacement for lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Material and labour in replacement for self ballast LED retrofit lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and directed.

Supply and fixing in replacement for LED lights fitting 1 x 20 W, 220 V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.95, 100 Lumen / Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete (4' ft long) with LED rod 20 watt, 230 Volts 50 Hz complete all as specified and directed.

Supply and fixing in repair LED light fitting 1 x 9 W / 1 X 10 W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Taking down existing unserviceable ceiling fan repair / maintenance including replacement of unserviceable spare parts i.e. bearing, bush, PVC connector, PVC clamp, canopy, capacitor, including painting, rewinding of any make / type and size (1200/1400 mm sweep) with super enamelled copper wire of appropriate gauge as existing to obtain the specified and satisfactory RPM as per manufacturer's specification, including replacement of all insulation materials, varnishing, heating, drying, assembling of stator / rotor, connection and testing complete all as specified and directed.

Supply and fixing in repair exhaust fan, steel body AC single phase 230 V of size 300mm sweep with blades and frame and louvers including taking down old one and deposited to MES store. Making holes for 300 mm exhaust fan of suitable shape and size into or through brick walls including plastering for making good to the original surfaces of any description disturbed including painting / distemper matching with the existing colour including taking down old one and deposited to MES store complete all as specified and directed. Note: - The rates include for making good to the original surfaces of any description disturbed including painting / distemper matching with the existing colour.

Material and labour in replacement for distribution board double door sheet steel phosphatised powder painted for MCB / distribution board with copper bus bar and neutral link earthing stud TPN 4 way 415 volts doubled door including taking down old one complete all as specified and directed.

Supply and fixing in repair 415 V 10 KA 'B' curve miniature circuit breaker (MCB) of TPN 100 Amp poles and current carrying capacity in the distribution board complete with connection, testing and commissioning complete all as specified and directed.

Material and labour for replacement of distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and directed by Engineer-in-Charge. Note: - Distribution board and MCB's should be of same make.

Supply and fixing in replacement SPN 40 to 63 Amp rating 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB distribution board complete with connection, testing and commissioning complete all as specified and directed.

Supply and fixing in replacement 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp, in the MCB distribution board complete with connection, testing and commissioning complete all as specified and directed.

Material and labour for earthing complete with galvanised mild steel earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 metre deep below normal ground level with top edge of the earth plate not less than 1.5 metre below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC (1:2:4) type B-1 precast RCC cover slab using reinforcement with suitable handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep and making good bottom surface for laying / removing of cable complete all as specified and directed in hard soil.

Supplying and laying and testing cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured, electric power cable (Heavy duty) with stranded aluminium conductor 1100 V grade cross sectional area 25 Sqmm, 3.5 core in and including taking out old one complete all as specified and directed.

Material and labour for sand filling in, cushioning bed of cable and consolidation complete all as specified and directed.

Supply and laying common burnt clay building sub class `B' bricks, laid over sand cushioning laid at right angle along with cable complete all as specified and as directed.

Returning, filling in excavated soil in trenches, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

Removal of excavated any type of soil to a distance not exceeding 50m complete all as specified and directed.

Supplying and laying in repair galvanised iron tubing light graded including all accessories for encasing cables for mechanical protection, laid under plinth / floors / path culverts with complete accessories such as bends / sockets / reducers / saddles including necessary threading / drilling works of size 40mm complete all as specified and directed. Note: - Mild steel work will be measured under separate item in schedule.

Material and labour for point wiring for one light / fan / call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 Sqmm copper conductor multistranded FRLS, PVC insulated (unsheathed) drawn into and including new concealed PVC rigid / 1.8mm wall thickness ISI marked including new cast iron / pressed steel terminal boxes including 3.00 mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified and as directed: - Notes: - (a) Wiring shall be done by using proper colour coding. (b) Earth wire shall be of green colour. (c) On RCC roof / ceiling PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engineer-in-Charge.

Supply and fixing switch piano, flush type single pole one way 5 Amps, 240 Volts complete all as specified and as directed.

Supply and fixing ceiling rose 3 Phase / PVC / polycarbonate isolated body complete all as specified and as directed.

Material and labour for lamp holder, PVC / Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Material and labour for self ballast LED retrofit lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and as directed.

Supply and fixing LED light fitting 1 X 9W / 1 X 10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing exhaust fan made of sturdy engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, copper winding of sweep 300m complete all as specified and as directed.

Material and labour for distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 2 way 240 Volts double door complete all as specified and as directed by Engineer-in-Charge. Note: - Distribution board and MCB's should be of same make.

Supply and fixing 240 V, 10 KA 'B' cure miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 Amps, in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and laying and testing cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured, electric power cable (Heavy duty) with stranded aluminium conductor 1100 V grade cross sectional area 10 Sqmm, 2 core in and including taking out old one complete all as specified and as directed.

Supply and fixing LED lights fitting 1 x 20 W, 220 V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.95, 100 Lumen / Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete (4' ft long) with LED rod 20 watt, 230 Volts 50 Hz complete all as specified and directed.

M/s KULDEEP KUMAR CONTRACTOR (BID ID -3100789)

M/S Sukhmani Construction Co. (BID ID -3100058)