SPECIAL REPAIR TO BLDG NO P-42 ( OTM ACCN) BHALUKMARA, SPECIAL REPAIR TO BLDG NO T-10 ( BATHROOM AND TOILET ) AT ROWRIAH AND SPECIAL REPAIR TO BLDG NO T-7 AT ROWRIAH AT JORHAT MIL STN UNDER GE JORHAT

Amount

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets, complete all as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar complete all as directed.

Taking down cement plaster from brick or concrete surfaces of any description including racking out joints, hacking for key, scrubbing down with water etc complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4.0 Sqm each etc complete all as specified and as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) n. exc. 1.5 Sqm each etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises complete all as directed.

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) etc complete all as specified and as directed.

Dismantling water tanks of capacity exceeding 250 litres but not exceeding 500 litres including float valve and removing from site etc complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing with connections including cleaning for refixing or removal from site with all fittings complete all as specified and directed.(Note - :- excavation and necessary earthwork will be measured and paid separately under relevant items.)

Taking up or down 20 mm bore steel tubing with connections including cleaning for refixing or removal from site with all fittings complete all as specified and directed.(Note - :- excavation and necessary earthwork will be measured and paid separately under relevant items.)

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar etc complete all as specified and as directed.

Dismantling Asbestos cement (corrugated,semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section unframed work in any position complete all as specified and directed.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks,etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) etc complete all as specified and as directed.

Dismantling Plain or corrugated steel sheeting,any gauge, thickness, including Nainital or similar pattern roof coverings etc complete all as specified and as directed.

Demolition of Reinforced cement concrete as in Roofs, floors (other than ground floors), beams, staircases, landing,chajjas and similar suspended work etc complete all as specified and as directed.

Dismantling wrought iron or mild steel of any description not otherwise provided for etc complete all as specified and as directed.

Demolition of cement concrete (un reinforced) of any description and in any position not otherwise specifically provided for etc complete all as specified and as directed.

Dismantling boarding, any description, fixed in any position with nails etc complete all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground etc complete all as specified and as directed.

M&L for Brick work with sub class‘B’ bricks, old size , well klin burnt , straight or curved on plan exc 6m mean radius, built in cement sand mortar 1:6 etc complete all as directed.

M&L for Rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface other than fair face of brickwork and finishing surface even and smooth without using extra cement, complete all as specified and directed.

M&L for Rendering 10 mm thick, cement plaster, in cement mortar (1:6) on fair face of brickwork and finishing surface even and smooth without using extra cement, complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 ( Using 20 mm graded stone aggregate) as in fixing / blockage of holdfast , filling in hollow door frames and bed block etc complete all as specified and as directed.

M&L for 25 mm thick ,PCC 1:2:4 type B-0 ( Using 12.50 mm graded stone aggregate) as in floor and pavings etc complete all as specified and as directed.

M&L for false ceiling with powder coated EPOXED GI grid suspension system ( E-grid T-2420 or equivalent of armstrong having load carrying capacity of 12.5 Kg/Sqm with mid span deflection not exceeding 1/360 span with hanger spacing of 1200 mm C/c ) consisting of main runner 3600 mm long,cross tee 1200 / 600 mm long and wall angle. The wall angle shall be fixed on PVC dash fasteners on the perimeter of the wall with stainless steel screws at a interval 300 mm C/c.The main runners to be placed @ 1200 mm, the cross tee of 1200 mm shall be inserted in the pre cut slots of main runner at regular interval of 600 mm to form a modular grid of 1200 mm x 600 mm.Additional cross tee of 600 mm shall be placed perpendicular to the cross tee 1200 mm long to form grid of size 600 mm x 600 mm with and including 6 mm thick HPSC ( High Pressure Stem Cured) oceanic , pre-primed, self embossed , textured designer board , water , termite and fire resistant for insulation and accoustic purpose to be placed in the grid system duly suspended with 2 to 3 mm dia GI wire hangers fixed with steel dash through fasteners from purlin with butterfly clips ( weight 0.007 Kg / clip) , hold down clips ( weight 0.0035 kg / clip) with provn of light fittings and fixtures etc complete all as manufacturer's instruction ,specified and shown on page No XIV & XV of SSR Part - II ( Rates) and as directed.

S&F Pressed steel frames 125 X 60 mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete all as specified and as directed.

S&F Pressed steel frames 105 X 60 mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete all as specified and as directed.

S&F factory made solid PVC moulded door designer shutter 35 mm thick comprising of 30 mm thick solid particle board in centre core , with 2 , 4 or 6 raised panel design with 2 mm thick moulded prelam PVC sheet on the front face & 2 mm prelam PVC sheet on back face , fixed or laid on to flush doors by using rubber based adhesive etc complete all as specified and as directed.

S&F Factory made solid panel wire gauzed PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S.tubes. The wire gauge shall be stretched to tighten firmly etc complete all as specified and as directed.

S&F aluminium anodised barrel tower bolt, extruded type, 200 mm long, complete all as specified and directed.

S&F aluminium anodised barrel tower bolt, extruded type, 150 mm long, complete all as specified and directed.

S&F aluminium handles, cast type, anodized, 150 mm size, complete all as specified and directed.

S&F aluminium handles, cast type, anodized, 125 mm size, complete all as specified and directed.

S&F mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and directed.

S&F aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed,300 mm etc complete all as specified and directed.

S&F in repair floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor , overall length of cover plate 150 mm etc complete all as specified and directed.

S&F 100 mm Butt hinges,medium weight,cold rolled mild stainless steel, and fixed etc complete all as specified and directed.

S&F in repair door closer aluminium extruded section hydraulically regulated designation No. 2, universal type , suitable for door shutter of 701 to 850 mm in width and of weight between 36 to 60 kg etc complete all as specified and directed.

S&F in repair 300 mm stainless steel ordinary rat tail rodpattern springs including roller and roller plate etc complete all as specified and as directed.

S&F MS barrel tower bolt,200 mm long, stove enamelled black with bright bolt etc complete all as specified and directed.

S&F MS pressed door handle ,150 mm long, oval type , stove enamelled black with bright bolt etc complete all as specified and directed.

S&F Mild steel sliding door bolts,plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed ,300 mm etc complete all as specified and directed.

S&F 125 mm Butt hinges,medium weight,cold rolled mild stainless steel, and fixed etc complete all as specified and directed.

S&F aluminium sliding window with powder coated ( minimum thickness of powder coating 50 micron) including following components / specifications complete all as specified and as directed. (i) Two leaf glazed sliding shutter and one leaf gauged ( fly proofing) sliding shuttter. (ii) Opening of windows exceeding 0.90 sqm but not exceeding 1.50 sqm. (iii) Thickness and weight per meter length of aluminium frame and section of shutter as per details shown on drawing. (iv) All vertical and horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading,screws etc . (vi) Rest all as specified in drawing No. CEZ/2015/TD/007 SHEET No IR/5 , 2R/5 , 3R/5, 4R/5 & 5R/5. Note 1:- Sheet glass, aluminium grill and stainless steel wire mesh shall be measured and paid against respective items of BOQ and all other items as shown on drawing shall be included in quoted rate. Note 2:- Only opening size of windows shall be measured and consider for payment.

S&F aluminium sliding window with powder coated ( minimum thickness of powder coating 50 micron) including following components / specifications complete all as specified and as directed. (i) Two leaf glazed sliding shutter and one leaf gauged ( fly proofing) sliding shuttter. (ii) Opening of windows exceeding 1.50 sqm but not exceeding 2.40 sqm. (iii) Thickness and weight per meter length of aluminium frame and section of shutter as per details shown on drawing. (iv) All vertical and horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading,screws etc . (vi) Rest all as specified in drawing No. CEZ/2015/TD/007 SHEET No IR/5 , 2R/5 , 3R/5, 4R/5 & 5R/5. Note 1:- Sheet glass, aluminium grill and stainless steel wire mesh shall be measured and paid against respective items of BOQ and all other items as shown on drawing shall be included in quoted rate. Note 2:- Only opening size of windows shall be measured and consider for payment.

S&F MS Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 etc complete all as specified and as directed.

S&F 5 mm thick sheet glass, ordinary quality in squares not exceeding 0.50 sqm in each pane in panels of aluminium windows, ventilators etc fixed with glazing clips, rubber beading and EDPM gasket etc complete all as specified and as directed.

S&F aluminium anodised grill of design ''DG-104' pattern made out of 7.5 mm plate and finished grill having 7.5 mm width and 6 mm thick etc complete all as per manufacturer's instruction and specified and as directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and as directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 450 mm length etc complete all as specified and directed.

S&F in repair Pillar tap, cast copper alloy,fancy type with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' withlong screwed shanks and fly-nuts,screwed for iron pipe and fixed 15 mm dia complete all as specified and as directed. Make :- Jaquar cat part No :QQT-7011 or equivalent make in Prayag / Hindware / Parryware.

S&F in repair angle stop cock, fancy type chromium plated screwed high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions 15 mm dia, and fixed complete all specified and as directed.Make Jaquar cat part no. QQT-7053 or equivalent make in Parryware / Hindware / Prayag.

M&L for granite slab of approved shade 20mm thick Granite (of any type) tiles machine cut, laid over and ncluding cement screed bed 20 mm thick and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing till entire satisfaction of Engineer in Charge etc complete all as specified and as directed.

S&F in repair curtain rod 25 mm dia , brass chromium plated , fancy type with bracket , fixed with wooden block / PVC through fastener wall with galvanised screws including necessary drilling and making good to disturbed surfaces etc complete all as specified and directed.

S&F Rotational moulded polyethylene 500 ltrs capacity water storage tanks , three layered, (ISI marked) (cylindrical vertical with closed top) hoisted and fixed in position in SSR Part-I including 20mm dia GI medium grade over flow pipe, approx lenght 1.5 mtr, 25 mm dia wash out pipe with pluged at one end complete all as specified and directed.Make:- Polycon / Polytuf / Sintex.

S&F 15 mm bore GI water tubing , medium grade, including new GI fittings such as tee, bend, nipple, socket, reducer, flange, union,on wall and ceiling or laid in floor etc complete all as directed.

S&F 20 mm bore GI water tubing , medium grade, including new GI fittings such as tee, bend, nipple, socket, reducer, flange, union , on wall and ceiling or laid in floor etc complete all as directed.

S&F in repair 20 mm bore Gun metal gate valve with iron wheel head screwed both ends for iron pipe etc complete all as directed.

S&F in repair Wash basin, Vitreous China, white, size 550 mm x 440 mm ,oval shape , counter top, including brackets (flat back or angle back type) any size,waste pipe , CP coupling 32 mm dia , including cutting for and pinning in ends of brackets or erecting stand complete all as specified. Make: Prayag cat part no. 4647 or equivalent make in Hindware / Parryware / Johnson

S&F in repair Vitreous china squatting pan of Orissa Pattern of size 580 x 440 mm white with ‘P’ or ‘S’ trap , front or back inlet but excluding flushing cistern and flush pipe including placing in position in floor and embedded in cushion of PCC type E2 ( using 40 mm graded crushed stone aggregates), 1:5:10 and finishing the top surfaces to match with the existing flooring complete all as specified and as directed .Make:- Prayag Cat part no. 4055 or equivalnt make in Cera / Hindware / Parryware

S&F in repair PVC (Plastic polymer Cistern) valve less, Symphonic action type, flushing cistern of capacity 10 litres, low level, white with inlet, ball valve,dual flush , manually operated with one PVC ball valve horizontal plunger type including provision of 32mm PVC flush pipe of required length and making connections complete all as directed by Engineer-in-Charge Make: SLIM LINE brand of Parryware Cat no. C08090 / SLEEK brands of Hindware or Prayag cat Part no. 504 .

M&L for 100 mm outlet dia cast iron fioor trap with gratings jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 ( using 20 mm graded stone aggregate ) etc complete all as specified and directed

S & F 75 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint fixed to walls including PVC clamps for securing pipe etc complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius with oval access door etc complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipe single socketed, in any length with rubber ring joint fixed to walls including PVC clamps for securing pipe etc complete all as specified and directed.

S&F 20 mm dia, Ball brass valves,high pressure,with polythene float and flynut complete,screwed for iron pipe or brass ferrule and fixed etc complete all as specified and directed.

S&F in repairs soap dish , chromium plated ,fixed with CP screws etc complete as specified and directed by Engr-in-charge.Make: Jaquar cat part No AQN-7731 or equivalent make in Prayag / Hindware / Parryware.

M&L for 75 mm thick plain cement concrete (1:3:6) type C-2 using 40 mm graded aggregates as in plinth protection or floor, finishing surface even and smooth without using extra cement ,laid in panels and joints of size 65 mm deep x 10 mm width , filled with sealing compound grade 'A' complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing etc complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed tothe stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. etc complete all as specified and directed.

M&L for Non - Skid ceramic tiles, coloured digital tiles , 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,conforming to IS 15622, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement sand mortar (1:6), complete all as specified and as directed

M&L for Non - Skid ceramic tiles, coloured digital tiles , 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,conforming to IS 15622, as on vertical surfaces such as dados , skirtings etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick screed bed or bedding layer of cement sand mortar (1:4), complete all as specified and as directed

M&L for Glazed ceramic coloured digital tiles, 350mm X 250mm or 450mm X 350mm , 7mm thick, conforming to IS 15622, on vertical surfaces of wall such as dados, skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick screed bed or bedding layer of cement sand mortar (1:3), complete all as specified and as directed.

M&L for Non - Skid ceramic tiles, coloured tiles , 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,conforming to IS 15622, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement sand mortar (1:4), complete all as specified and as directed

M&L for complete removal of existing treatment of wall by scrapping , rubbing with iron brush and washing with water and applying two coats of acrylic emulsion distemper over and a coat of wall primer over and including 1 mm thick wall care putty chalk whitening etc complete all as specified and as directed.

Materials and Labour for preparation of newly plastered surfaces of wall and applying two coats of acrylic emulsion distemper over a coat of wall primer over and including 1 mm thick wall care putty chalk whitening etc complete all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of steel and applying two coats of synthetic enamel paint over a coat of red oxide primer ,surface not exceeding 10 cm in width or girth including necessary preparation of surfaces complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel and applying two coats of synthetic enamel paint over a coat of red oxide primer ,surface exceeding 10 cm in width or girth including necessary preparation of surfaces complete all as specified and directed.

M&L for preparation of old or previously treated surfaces of steel roof sheeting of any description and applying a coat of synthetic enamel paint ,surface exceeding 10 cm in width or girth including necessary preparation of surfaces complete all as specified and directed.

S&F in repair Bib cock , cast copper alloy,chromium plated, long body with crutch or butterfly handle , fancy type 15mm , screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make :Prayag cat part no. 8506 or equivalent make in Parryware / Hindware.

S&F 15 mm bore stop valve, fancy type, chromium plated , cast copper alloy with long shank and cup, concealed type, with round headed knob , screwed both ends for iron pipe or for unions and fixed etc complete all as specified and as directed. Make:- Marc ESSCO ES 513 / Hindware Cat No. F200007 or equivalent of Jaquar/Prayag.

S&F in repair Shower Rose brass chromium plated 125 mm size with swivel joints etc complete all as specified and as directed.Make:- Prayag / Hindware / Cera

S&F in repair brass chromium plated tubular towel rail 600 mm long between the flanges and 20 mm dia etc complete all as specified and as directed.Make:- Prayag cat part no. BA-30 or equivalent make of Parryware / Hindware.

S&F in repairs Gratings , chromium plated , 100 mm dia, fixed in floor with neat cement slurry to match the existing etc complete as specified and directed by Engr-in-charge.Make - Prayag / Hindware / Parryware.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded etc complete as specified and directed by Engr-in-charge.

S&F 3 mm thick sheet glass ,ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each pane etc complete as specified and directed by Engr-in-charge.

S&F 4 mm thick , figured sheet glass , ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each pane etc complete as specified and directed by Engr-in-charge.

M&L for RCC 1:1.5:3 type-A-1, ( using 20mm graded stone aggregate) as in Beams, cantilevers, bressummers,lintels over 1.5m span etc complete all as specified and as directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers,lintels, cantilevers, shelves including supports,overhangs,etc. also splays between floors andbeams, etc. etc complete all as specified and as directed.

M&L for Mild steel TMT deformed bars, 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D complete all as specified and directed.

M&L for Mild steel TMT deformed bars, 5 mm dia and over upto 10 mm dia , cut to length bent to shape required, including cranking, bending spirally for hooping for hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D in stirrups, spacers and binders complete all as specified and directed.

M&L for Mild steel TMT deformed bars, 5 mm dia and over upto 10 mm dia , cut to length bent to shape required, including cranking, bending spirally for hooping for hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality confirming to Fe 500D etc complete all as specified and directed.

Materials and Labour for plain cement concrete (1:3:6) type C1 using 20 mm graded aggregate as in surface channels and drains including necessary formwork etc complete all as specified and as directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement sand mortar 1:4 etc complete all as directed.

S&F MS Rolled sections as in main and cross beams, hip and jack rafters;purlins where connected to common rafters and running rails and guides for sliding doors;fixed with angle cleats or otherconnecting plates conforming to Fe 410 -W (Gde-E- 250) quality- A complete all as specified and directed.

S&F Pre-painted, galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering/cladding to wall, fixed with self-tapping screws,complete all as specified and directed.

S&F Pre-painted, galvalume aluminium zinc coating GI based plain steel sheet, 0.50 mm thick of any colour, having tensile strength of 550 Mpa, as in roof covering /cladding to wall / eaves and similar nature of work , fixed with self-tapping screws,complete all as specified and directed.

M&L for Hardcore of crushed stone, gauge n exc 63mm, deposited, spread and levelled well in layers n exc 15cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

M&L for 100 mm thick plain cement concrete 1:4:8 type D- 2, (using 40mm graded stone aggregate) as in sub base of floor , finished even and rough etc complete all as specified and as directed.

M&L for 40 mm thick plain cement concrete 1:2:4 type B-1, (using 20 mm graded stone aggregate) as in floor , finished even and rough without using extra cement etc complete all as specified and as directed.

M&L for rendering 15 mm thick, cement plaster, in cement mortar (1:6) on surface fair face of brickwork and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Materials and Labour for rendering 5 mm thick, cement plaster, in cement sand mortar (1:4) mixed with water proofing compound @ 3% by the weight of cement used or as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surface in walls, complete all as specified and directed. Note: - (Water proofing compound shall be measured and paid separately)

Supply only integral water proofing compound ISI marked etc complete all as specified and as diretced.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm prelam PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing etc complete all as specified and directed.

S&F Factory made solid panel prelam PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and both side Prelam PVC sheet used, Stile and rails feathered at edges plain colour PVC sheets for top rail,lock rail & bottom rail on either side & as gap insert for top rail & bottom rail;Panelling of prelam PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. etc complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete etc complete all as specified and directed.

S&F 3 mm thick ,frosted or obscured , sheet glass ,ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each pane etc complete as specified and directed by Engr-in-charge.

M&L for preparation of new or previously untreated surfaces of wall and applying three coats of white wash etc complete all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of wall including cornices , pilasters , etc and applying two coats of cement base paint over and including a coat of suitable primer etc complete all as specified and as directed.

S&F in repair 15 mm dia 3-layer PP-R P o l y p r o p y l e n e random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimocrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polyproplyne random fittings fixed complete to walls, ceilings or in floors etc.complete all as specified and as directed.

S&F in repair 20 mm dia 3-layer PP-R P o l y p r o p y l e n e random copolymer) pipes SDR 7.4 & SDR 11 UV stablised and antimocrobial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polyproplyne random fittings fixed complete to walls, ceilings or in floors etc.complete all as specified and as directed.

S&F in repair 15 mm bore Gun metal gate valve with iron wheel head screwed both ends for iron pipe etc complete all as directed.

S&F unplasticized PVC pipes 32 mm bore of pressure rating 10 kgf/sq. cm etc complete all as specified and as directed.

S&F in repair Vitreous China urinals, half stall type , white , complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; with brackets,flush pipe, grating and Union for discharge pipe. complete all as specified. Make: Prayag Cat Part No Cat. No.: 4998 or equivalent make in Hindware / Parryware.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified. Make: Prayag / Hindware / Parryware.

S&F in repair Waste coupling of PTMT (half or full threaded) 32 mm suitable for urinals, (Minimum weight 32mm-45gms complete all as specified. Make: Prayag / Hindware / Parryware.

S&F 75 mm dia PVC (SWR) fioor trap including jointing to pipe solvent cement etc complete all as specified and directed

S&F PVC (SWR) pipes , 110 mm bore , double socketed in any length with rubber ring joints fixed to walls with mild steel clamps made out of flat iron of size 25 mm x 3 mm including necessary nuts and bolts etc complete all as specified and as directed.Make:- Supreme / Prayag / Kanha / Prince

S&F PVC (SWR) pipes , 110 mm bore , double socketed in any length with rubber ring joints , laid in trenches etc complete all as specified and as directed.Make:- Supreme / Prayag / Kanha / Prince

M&L for Concrete bed of PCC 1:3:6 type C-2 ( using 40 mm graded stone aggregate) to 100 mm bore drain pipes including packing under,and haunching against the sides of pipes after they are laid and tested;in etc complete all as specified and as directed.

S&F PVC (SWR) pipes , 75 mm bore , double socketed in any length with rubber ring joints fixed to walls with mild steel clamps made out of flat iron of size 25 mm x 3 mm including necessary nuts and bolts etc complete all as specified and as directed.Make:- Supreme / Prayag / Kanha / Prince

S&F 75 mm bore PVC (SWR) bend with access door any radius complete all as specified and directed.

S&F 110 mm bore PVC (SWR) junction single 'T' equal or unequal etc complete all as specified and directed.

S&F 75 mm bore PVC (SWR) vent cowl etc complete all as specified and directed.

M&L for mild steel work such as in bands, straps, supports or stays for RWP , ventilating pipes , clamps , hold fasts and wall ties etc conforming to Fe 290, Grade E-165 etc complete all as specified and directed.

S&F Vitreous china urinal partition white of size 310 x 700 mm , fixed on wall with CP screws etc complete all as specified and directed.Make:- Prayag / Hindware / Cera.

S&F PVC (SWR) gully trap 125 /110 mm bore , setting and jointing with solvent cement etc complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good to pipe and rendering in cement and mortar 1:4, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l ( using 20 mm graded stone aggregate ) smooth finished, and reforming benching as required for 100 mm internal dia of pipe etc complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-1 ( using 20 mm graded stone aggrgate ) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses, lacing courses, parapets andrailings upto 60 cm in height,copings, kneelers, apex stones, bed plates, kerbs not provided , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed etc complete all as specified and as directed.

M&L for Chequered ceramic coloured tiles, 12 mm thick ( square / rectangular) area of each tiles exceeding 0.09 sqm but n.exc 0.16 sqm , conforming to IS 4457- 2007 , on floor , set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles , over and including 20 mm thick screed bed or bedding of cement sand mortar 1:6 etc complete all as specified and as directed.Make:- Johnson ''Endura'' / Somany ''Durastone'' / Regency ''Duro''

S&F Second class hard wood timber scantlings, wrought, in unframed works and in any position, fixed with nails complete all as specified and directed.

S&F Anodised aluminium snap grid ( size of grid 605mmx605mm) frame work for false ceiling including GI wire 4 mm thick as a suspender for GI snap grid etc complete as specified and as directed.

M&L for 4 mm thick, high pressure steam cured (HPSC) non asbestos fibre cement building boards fixed or laid / inserted to timber/ GI / Aluminium framework with stainless screws etc complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation , filling and mass concrete etc complete all as specified and directed

M&L for Brickwork with sub class ‘B’ bricks, well klin burnt , old size , straight or curved on plan to any radius , built in cement sand mortar 1:4 etc complete all as directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in pre cast cement concrete block masonry with solid blocks exc 10 cm in width and setting in cement sand mortar 1:4 etc complete all as specified and directed

Materials and Labour for preparation of newly plastered surfaces of wall and applying two coats of acrylic emulsion distemper over a coat of wall primer etc complete all as specified and as directed.

S&F 35 mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, and both faces shall be covered with decorative face veener with lipping / frame to match etc complete all as specified and directed.

S&F 4 mm thick , sheet glass , ordinary quality and glazing with oil putty in squares not exceeding 0.50 sqm in each pane etc complete as specified and directed by Engr-in-charge.

M&L for preparation of old or previously treated surfaces of wood of any description and applying a coat of synthetic enamel paint ,surface exceeding 10 cm in width or girth including necessary preparation of surfaces complete all as specified and directed.

M&L for Preparing surfaces of wood and wood based materials,new or old, of any description and girth, not otherwise described and treated with a coat of creosote complete all as specified and directed.

M&L for RCC M-25 (Design mix) (using 20 mm graded stone aggregate) as in Beams, cantilevers,bressummers, lintels over 1.5m span etc complete all as specified and as directed.

M&L for RCC M-25 (Design mix) (using 20 mm graded stone aggregate) as in Chajja etc complete all as specified and as directed.

M&L for RCC M-25 (Design mix) (using 20 mm graded stone aggregate) as in Slabs supported on walls,beams and columns in floors,roofs, landings, balconies,canopies, deck slabs and in shelves and the like etc complete all as specified and as directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings,girders, bressummers,lintels, cantilevers, shelves including supports,overhangs,etc. also splays between floors and beams, etc. complete all as specified and as directed.

M&L for Formwork to chullah hoods, chajjas,troughs and similar items including edges etc. complete all as specified and as directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick , laid over and including 15 mm thick cement screed base in cement sand mortar 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick in riser of steps, skirting, dado and pillar laid over and including 10 mm thick cement screed base in cement sand mortar 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete complete all as specified and as directed.

S&F mild steel work as in tubular trusses , purlins, and posts etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 etc complete all as specified and as directed.

Excavating in trenches n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft / loose soil etc complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25 Cm thick as in soft/loose soil etc complete all as specified and as directed.

Removing excavated materials (soil) to a distance n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed.

Supply and filling in dry and clean river sand in cable trenches before and after the cables are laid, as in sand cushioning to cables, complete all as specified and as directed.( Note:- Only punned thickness of sand cushion bed shall be measured and paid.)

Supply and laying common burnt clay building bricks, sub-class‘B’ designation 75, old size bricks, in cable trenches, as cable protection, complete all as specified and directed.

Supply,laying, jointing and testing of , XLPE insulated, PVC sheathed, armoured, heavy duty electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 16 sqmm 2 core with aluminium lugs etc complete all as specified and directed.

Supply,laying, jointing and testing of , XLPE insulated, PVC sheathed, armoured, heavy duty electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 10 sqmm 2 core with aluminium lugs etc complete all as specified and directed.

Supply,laying, jointing and testing of , XLPE insulated, PVC sheathed, armoured, heavy duty electric cables with aluminium conductor for working voltage up to and including 1100 volts, of cross sectional area 25 sqmm 3.5 core with aluminium lugs etc including taking down old unserviceable one complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete including all fittings and fixtures such as switches, lamp holders, regulators, switch, socket outlets, bell push, ceiling rose etc removing material to store for keeping in safe custody for reuse at site and making good disturbed surfaces of walls with cement sand mortar (1:6) and white/colour wash to match with existing surfaces etc complete all as directed by Engineer -in -Charge .

Taking down copper/aluminium sub main wiring complete and removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

M&L for Point wiring ( Concealed type) with single runs PVC insulated FRLSH grade, 1100V grade cable with multistranded copper conductor of size 1.5 Sqmm (Nominal area) (ISI Marked) drawn in and including PVC Casing capping 20 mm bore with all fittings and accessories including PVC rectangular board of suitable size and drawing continuous earth wire of PVC insulated FRLSH grade, unsheathed stranded copper conductor of size 1.5 Sqmm (ISI Marked) as continuous earth wire terminated in and including sunken box for following type of point wiring including making good disturbed of wall complete all as specified in SSR Part-I, 2009 and Part-II, 2010 and as directed by Engineer-in- Charge for one light point / one 3 pin socket outlet 5/6 Amps / one bell point / one fan point etc on independent board controlled by one one way switch.

Supply and fix, Switch piano (ISI marked) Single pole 240 volts, flush type, one way 5 Amps complete all as specified and directed.

M&L for Point wiring ( Concealed type) with single runs PVC insulated FRLSH grade, 1100V grade cable with multistranded copper conductor of size 2.5 Sqmm (Nominal area) (ISI Marked) drawn in and including PVC Casing capping 20 mm bore with all fittings and accessories including PVC rectangular board of suitable size and drawing continuous earth wire of PVC insulated FRLSH grade, unsheathed stranded copper conductor of size 2.5 Sqmm (ISI Marked) as continuous earth wire terminated in and including sunken box for following type of point wiring including making good disturbed of wall complete all as specified in SSR Part-I, 2009 and Part-II, 2010 and as directed by Engineer-in- Charge for one one 3/5 pin switch socket combination 15/16 Amps etc on independent board controlled by one one way switch.

Supply and fix Socket socket combination (ISI marked), 2/3 pin and 15/16 Amps, flush type, multipurpose, 240 volts complete all as specified and as directed.

Material and labour for sub main wiring with two single core 6.0 sqmm FRLSH, ISI marked PVC insulated multi stranded, unsheathed copper conductor cable and one single core unsheathed FRLSH , ISI marked, PVC insulated multistranded copper conductor cable of size 6.0 sqmm green colour as earth lead including PVC casing capping of suitable size complete all as specified and directed. (Note: Two runs of 6.0 sqmm cable , one run of earth wire of 6.0 sqmm and one run of PVC casing capping shall be measured as one length).Make- Cable- Finolex / KEI /Havells, PVC Casing Capping- Presto plast/Finolex/Kalinga.

S&F Ceiling rose, 3 terminals PVC/polycarbonate, isolated body complete all as specified and directed.

S&F Decorative ultra slim linear LED batten light fitting with co extruded polycarbonate body enviornmental friendly, energy efficient , E-LITE LED GREEN suitable for 22 watt LED 6000K , 240 volts LED tube light ( single side connection ) including 1 x 22 watt LED tube rod etc complete all as specified and directed.Make:- Wipro / Havells / Philips / Crompton / Bajaj.

S&F , metallic , heavy duty exhaust fan AC single phase 230/240 volts of sweep 300 mm , 1400 RPM with metallic self closing louver, making necessary electric connection with flexible copper conductor cable 1.5 sqmm 3 core PVC insulated including cutting holes of appropriate size in brick wall or concrete wall and making good to disturbed surfaces with cement sand mortar 1:3 with necessary paint /white wash to match the existing etc complete all as specified and as directed. Make:- Usha / Crompton / Havells / Bajaj.

S&F in repair factory made MCB DB SPN , 8 ways , double door, IP-43 with 200 amps rated busbar ,earth bar , neutral links complete including blanking plates etc complete all as specified and directed. [Make:- L&T ,Cat No.DBSPN008DD or Legrand Cat part No 5076-10 or equivalent Model of Make Hager / Siemens]

S&F in repair MCB SP 6-32 amps 240 volts , breaking capacity 10 kA ''C'' series etc complete all as specified and directed. Make:- Legrand cat part No 603231 37 or equivalent make in L&T / Siemens

S&F in repair MCB SPN 40 amps 240 volts , 50 Hz , breaking capacity 10 kA ''C'' series etc complete all as specified and directed. Make:- Legrand cat part No 603248 54 or equivalent make in L&T / Siemens.

S&F New generation energy saving building security light luminiries housing of versatile pressure die cast aluminium IP-66 with high power LED light 25 watt 230 volts 50 Hz with ballast / charging unit including all accessories , pre-wired including connecting up with 2.5 sqmm multi stranded aluminium conductor 2 core cables not less than 3 m length ,fixed to pole / wall etc and testing etc complete all as specified and directed.Make:- Wipro Cat part No LR02-291-XXX-57-XX or equivalent make in Havells / Crompton / Bajaj.

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less' than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia size upto 7.5 meter by means of bolts, nuts, check nuts and washers of galvanised iron or steel protected by medium grade 50 mm dia 5 meter long GI pipe and connected to main control panel and GI pipe 20 mm medium grade as watering pipe including funnel , wire mesh , PCC pit of PCC 1:2:4 type B-2 ( using 20 mm graded stone aggregate , RCC cover slab 40 mm thick with 8 mm TMT bar @ 15 C/c including necessary earth work ,all as shown in electrical plate No. 5 , connected to earthing test point all as specified or indicated including testing on completion etc complete all as specified and as directed.

PEE BEE INDIA

M/S N M TRADERS