PROVIDING FOR FURNITURE OF CONSTRUCTION OF VIDEO CONFERENCING ROOM IN JUDGES LOUNGE AREA (NEAR OLD CONFERENCE HALL) AND REDESIGING THE COMMITTEE ROOM IN HONBLE PUNJAB AND HARYANA HIGH COURT, SECTOR 1, CHANDIGARH.

Supply of Wooden Chair made of 1st Class teak wood. Back & seat upholstered with 32 dnsity foam cushion. Finish with PU Polish. Complete as per your drawing to the entire satisfaction of Engineer in Charge.

Supply of Wooden Conference table size 15'x4' made of 18mm thick BWP ply, finish with 4mm thick teak Vnner, Edges of the table shall be finish with teak wood beading. Top with veneer & center glass. Finish with PU Polish. Complete as per your drawing to the entire satisfaction of Engineer in Charge.

Supply of Wooden Memorabilia panel size 9'7" x 4'6" with Wooden Edges & Fabric. Finish with PU Polish. Complete as per your drawing to the entire satisfaction of Engineer in Charge.

Supply of Wooden 3 seater sofa made of 1st class teak wood. Back & seat upholstered with 32 density foam cushion. Finish with PU Polish. Complete as per your drawing to the entire satisfaction of Engineer IN Charge.

Supply of Wooden single seater sofa made of 1st class teak wood. Back & seat upholstered with 32 density foam cushion. Finish with PU Polish. Complete as per your drawing to the entire satisfaction of Engineer IN Charge

Supply of Wooden Center Table made of 1st class teak wood. Finish with PU Polish. Complete as per your drawing to the entire satisfaction of Engineer IN Charge.

Supply and installation of wooden workstation of size 3'-6"(W) x 2'-6"(H) having keyboard tray, drawers cabinets, made up of 18mm thick HDHMR board finished with 4mm thick teak ply followed by PU polish. The workstation shall be finished with 1 mm thick Laminate inner side. The backing shall be provided with 6mm thick HDHMR ply. The rate also include the cost of drawer channel, handles, piano hinges, fevicol , masking tape, making holes, screws and nails etc complete in all Aspects to the entire satisfaction of Engineer IN Charge

Supply of Wooden chair made of 1st class teak wood. Back & seat upholstered with 32 density foam cushion. Finish with PU Polish. Complete as per your drawing to the entire satisfaction of Engineer IN Charge

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note:- Butt hinges and necessary screws shall be paid separately) Second class teak wood 30 mm thick shutters DSR 9.5.1.2

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood DSR 9.1.1

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws DSR 9.21.3

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 75mm overall thickness partition with 12.5 mm thick double skin tapered edged plain Gypsum plaster board conforming to IS: 2095: (part I): 2011 (Board with BIS certification marks) DSR 9.105.2

Providing and fixing 4mm thick teak ply (ISI marked) with exisitng wooden members including the cost of nails, fevicols etc. complete in all respect to the entire satisfaction of Engineer-in-charge.

Providing and fixing 6mm thick commercial ply (ISI marked) on the exisitng wooden members including the cost of nails, fevicols etc. including painting two coats of synthetic enamel paint over one coat of primer complete in all respect to the entire satisfaction of Engineer-in-charge.

Melamine polishing on wood work (one or more coat). DSR 13.114

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm DSR 9.100.1

Renewing glass panes, with wooden fillets wherever necessary:Float glass panes of nominal thickness 4 mm (weight not less than 10kg/sqm) DSR 14.6.1

Extra for providing frosted glass panes 4 mm thick (weight not less than 10 kg per sqm) instead of ordinary float glass panes 4 mm thick (weight not less than 10 kg per sqm) in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured). DSR 9.12

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. DSR 9.83