Construction of Inspection Hut with Chowkidar Quarter and Driver Rest Room at Mankote District Poonch

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:All kinds of soil :

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in :Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All works upto plinth level 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete.

Centering and shuttering including strutting, propping etc. and removal of form for:Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Centering and shuttering including strutting, propping etc. and removal of form for: Columns, pillars, piers, abutments, posts and struts.

Centering and shuttering including strutting, propping etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platforms.

Edges of slabs and breaks in floors and walls Under 20 cm wide

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Mild steel and medium tensile steel bars

CEMENT PLASTER 12mm Cement plaster of mix:1 : 6 ( 1 cement : 6 coarse sand)

6MM CEMENT PLASTER 6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):Second class deodar wood

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws.First class deodar wood

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge First class deodar wood

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately).

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick.Plain particle board flat pressed, 3 layer or graded wood particle board medium density Grade I, IS : 3087 marked

Providing and fixing chromium plated brass handles with necessary screws etc. complete : 125 mm

Providing and fixing chromium plated brass handles with necessary screws etc. complete : 100 mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :100x10 mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :150x10 mm

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 250x16 mm

Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : Twin rubber stopper

Providing and fixing chromium plated brass night latch of approved quality including necessary screws etc. complete.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with:(1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Filling stones excluding cost of stone on Horizontal level.

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 1 mm thick

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade on New work (two or more coats) over and including priming coat with water thinnable cement primer

Finishing walls with water proofing cement paint of required shade on New work (two or more coats applied @ 3.84 kg/10sqm)

Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Flooring with marble stone of specified thickness as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement:4 coarse sand) laid and jointed with grey cement slurry including rubbing, polishing and curing complete with:Agaria White

Extra for pre finished nosing to treads of steps of marble stone

Providing and fixing plain lining tongued and grooved, including wooden plugs complete with necessary screws and priming coat on unexposed surface Second class Deodar Wood 12mm thick

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc including priming coat with approved steel primer all complete. Fixed to openings / wooden frames with rawl plugs screws etc.

Applying priming coat: With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron/steel works

Painting steel work with deluxe multi surface paint of required shade to give an even shade. Two or more coats applied @ 0.90litre/10sqm over an under coat of primer applied @ 0.80litre/10sqm of approved brand and manufacture

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. G.I. pipes

Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for expansion joints. 300 mm wide

Providing and laying integral cement based water proofing treatment including preparation of surfaces as required for treatment of roofs, balconies, terraces etc consisting of following operations. Laying brick bats with mortar using broken bricks/ Brick Bats 25mm to 115mm size with 50% of Cement mortar 1:5 (1 Cement : 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 Cement : 5 coarse sand) admixed with water proofing compound conforming to IS 2645 and approved by Engineerin-charge to required slope and treating similarly the adjoining walls upto 300mm height including rounding of Junctions of walls and slabs)

SS Screws of sizes for structural glazing / ACP Cladding

Anchor Fastner - M10

Weather Sealant - Non Staining (600 ml)

Weather Sealant - Normal (300 ml)

Spacer tape 6.4 mm thick x 6 mm wide

EPDM Gasket in Kg (Above 60 g / m)

MS Brackets/Aluminium Alloy Brackets

SS Bolt with washer of different sizes for structural glazing / ACP Cladding

SS Screws of sizes for structural glazing / ACP Cladding

Protective Tape

Providing and supplying aluminium extruded tubular and otheraluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. (The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Toughened glass (Partition)

Toughened glass (Windows)

Providing and fixing white vitreous china pedestal type water closet(European type) with seat and lid , 10 liter low level white vitreous chinaflushing cistern and CP flush bend with fittings and C.I. brackets, 40mmflush bend, overflow arrangement with specials of standard make andmosquito proof coupling of approved municipal design complete,including painting of fittings and brackets, cutting and making good the walls and floors wherever required: W.C. pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-(a) White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge.PN-16 pipe , 25mm OD(SDR-7.4)

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer)pipes conforming to IS: 15801, UV stabilized and anti-microbial fusionwelded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge. PN-16 pipe , 32mm OD(SDR-7.4)

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing. Rectangular shape 453x357 mm

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour, weighing not less than 88 gms

Grating (C.I.) 180x180 mm

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour: Waste coupling 38mm of 83 mm length and 77 mm breadth weighing not less than 60gms.

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets 20 mm dia ( heavy type)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040mm bowl depth 250mm

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete,including painting of fittings and brackets, cutting and making good the walls and floors wherever required:Range of four urinal basins with 10 liter white P.V.C automatic flushing cistern..

Providing and fixing ISI marked M.S. pressed butt hinges bright finished with necessary screws etc. complete :100x58x1.90 mm

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.(i) Single socketed pipes 110 mm diametre

Providing and fixing on wall face un-plasticized Rigid PVC rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion. (i) Single socketed pipes 75 mm diametre

Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Structural steel work in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded

Carriage of materials including loading and unloading complete - Sand for an average 50 KM MT

Carriage of Materials including loading and unloading complete -Bajree for an average 05 Km by MT

Brick for an average 200 Km by MT

Water Supply Providing and fixing CP Brass Single lever telephonic wall mixer ofquality & make as approved by Engineer in charge. (a) 15 mm nominal dia

Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour: 600 mm long towel rail with total length of 645 mm, 78 mm wide and effective height of 88 mm, weighing not less than 190 gms

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with brackets of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms

Providing and fixing PTMT shelf 440 mm long, 124 mm width and 36 mm height of approved quality and colour, weighing not less than 300 gms.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing 18.32.1 Circular shape 450 mm dia

Providing and fixing toilet paper holder C.P. brass

Providing and fixing soil, waste and vent pipes : 100 mm dia.

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour: 18.69.1 Waste coupling 31mm of 79 mm length and 62 mm breadth weighing not less than 45gms

Providing and fixing 15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-incharge.

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet 100 mm diameter

Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge. For 22.22 mm outer dia x15 mm nominal dia threaded

Providing and fixing required Stainless Steel Fitting of press fit design of grade AISI 304 conforming to JWWA G116 standard with V-profile or M profile and with O-ring sealing gasket of EPDM material of required dia as per direction of Engineer-in-charge.

Equal Tee for 22.22 mm outer dia SS pipe

Equal Tee for 28.58 mm outer dia SS pipe

Reducing Tee for 28.58 mm X 22.22 mm outer dia SS pipe

Reducer for 28.58 mm X 22.22 mm outer Dia SS pipe

Reducer for 34.00 mm X 22.22 mm outer Dia SS pipe

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 20 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 25 mm nominal bore

Electrical wiring for light point/fan point/call bell point with 1.5 sq. mm. FRLS PVC insulated copper conductor singel core casbel in furface /recessed medum class pvc conduit with modular switch , modular plate, suitable G.I. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper comnductor singel cabel etc as req.

Wiring for light\power plug with 2x4 sq. mm FRLS PVC insulated copper conductor singel core cabel in surface\recessed medum class PVC conduit aslong with 1 no. 4 sq. mm. PVC FRLS insulated copper conductor singel core cabel in for loop earthing as req.

Wiring for cicuit/ submain wirring alongwith earth wire with the following size of FRLS PVC insulated copper conductor 'singel core cabel in surfacr/ recessed medum class PVC conduit as req. 2x1.5 sq. mm +1x1. sq.mm earth wire

Wiring for cicuit/ submain wirring alongwith earth wire with the following size of FRLS PVC insulated copper conductor 'singel core cabel in surfacr/ recessed medum class PVC conduit as req. 2x2.5 sq.mm+1x2.5sq.mm earth wire

Wiring for cicuit/ submain wirring alongwith earth wire with the following size of FRLS PVC insulated copper conductor 'singel core cabel in surfacr/ recessed medum class PVC conduit as req. 2x4.0sq.mm +1x 4.0 sq. mm earth wire

Wiring for cicuit/ submain wirring alongwith earth wire with the following size of FRLS PVC insulated copper conductor 'singel core cabel in surfacr/ recessed medum class PVC conduit as req. 2x6.0 sq. mm+1x6.0 sq. mm earth wire

Wiring for cicuit/ submain wirring alongwith earth wire with the following size of FRLS PVC insulated copper conductor 'singel core cabel in surfacr/ recessed medum class PVC conduit as req. 4X16 sq mm+2x 6.0 sq.mm earth wire

Supply and drawing following size of FRLS PVC insulated copper conductor 'singel core cabel in surfacr/ recessed medum class PVC conduit as req. 1x1.5 sq. mm

Supply and fixing of follo following size medum class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed comduit as req. 25 mm

Supply and fixing following modular switch/socket on the exisitying modular plate & switch box including connections but excluding modular plste etc. as req. 5/6 amp switch

Supply and fixing following modular switch/socket on the exisitying modular plate & switch box including connections but excluding modular plste etc. as req 15/16 A switch

Supply and fixing following modular switch/socket on the exisitying modular plate & switch box including connections but excluding modular plste etc. as req. 3 pin 5/6 A socket outlet

Supply and fixing following modular switch/socket on the exisitying modular plate & switch box including connections but excluding modular plste etc. as req. 6 pin 15/16 A socket outlet

Supply and fixing two module steped type electronic fan regulator on exisiting modular plate switch box including connection but excluding modular plate etc as req.

Supply and fixing modular blanking plate on existing modular plate & switch box excluding switch box etc. as,req.

Supply and fixing suitable G.I.box with modular plate and cover in front of surface or in recess, includijng providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and15/16 A modular switch,connection ,painting,etc as req .

Supply and fixing suiutable size of GI box with modular plate and cover in forent of surface or in recess,including providing and fixing 2 nos. 5/6 A modular socket outlet and 2 nos. 5/6 A modular swuitch, connection etc as rwq. (for light plug to be used in non residential buldings)

Supply and fixing following size/module GI. box alongwith modular base & cover plate for modular switches in recessed etc.as req. 1 or 2 module (75 mmx75mm)

Supply and fixing following size/module GI. box alongwith modular base & cover plate for modular switches in recessed etc.as req. 3 module (100mmx75mm)

Supply and fixing following size/module GI. box alongwith modular base & cover plate for modular switches in recessed etc.as req. 8 module(125mmx125mm)

Supply and fixing following way,horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V. on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, intreconnection, powder painted including earting etc. as req. ( but without MCB/RCCB/Isolator) 4 way(4+12) Double Door

Supply and fixing following way,horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V. on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, intreconnection, powder painted including earting etc. as req. ( but without MCB/RCCB/Isolator) 6 way(4+18) Double Door

Supply and fixing following way,horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V. on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, intreconnection, powder painted including earting etc. as req. ( but without MCB/RCCB/Isolator) 8 way(4 +24) Double Door

Supply and fixing 5 A to 32 A rating, 240/415 V, 10 KA, ''C'' curve ,miniature circuit breaker suitable for inductive load of following pole in exisiting MCB DB complete with connection, teasting and commessoning etc. as req. single pole

Supply and fixing 5 A to 32 A rating, 240/415 V, 10 KA, ''C'' curve ,miniature circuit breaker suitable for inductive load of following pole in exisiting MCB DB complete with connection, teasting and commessoning etc. as req. single pole and neutral

Supply and fixing rating, four pole 415 V isolator exisiting MCB DB complete with connection, teasting and commessoning etc. as req. 100 A

Supply and fixing of following electrical items as req. Fan Box

Supply and fixing of following electrical items as req. Fan sheet

Supply and fixing of following electrical items as req. A/B holder

Supply and fixing of following electrical items as req. LED lamp 9 watt

Supply and fixing of following electrical items as req. Deep box

Supply and fixing of following electrical items as req. LED Bulkhead 9/12 Watt

Supply and fixing of following electrical items as req. 25 sq mm Alum wire twin core

Supply and fixing of following electrical items as req. 16 sq mm Alum wire twin core

Celling fan 1200 mm swip alongwith rod upto 2' long as req.

Exhust fan 300 mm swip

Supply, installation , teasting and commessoning of 1.5 inverter type Ton split ACs (copper) (three star) hot & Cold (all weather)type of minimum capacity following size asdetailed below. each unit must provide cooling & dehumidification, be operatable via remote control, operate at 220-240 V AC supply with latest in vogue features. repairs made to wall ehereever erq. a) . Warrantee shall be provided for 12 month from the date of installation b).the compressor shell be wrrannted for 5 years from date of installation

supply, installation , teasting and commessoning of 2.0 inverter type Ton split ACs (copper) (three star) hot & Cold (all weather)type of minimum capacity following size asdetailed below. each unit must provide cooling &dehumidification, be operatable via remote control, operate at 220-240 V AC supply with latest in vogue features. repairs made to wall ehereever erq. a) . Warrantee shall be provided for 12 month from the date of installation b).the compressor shell be wrrannted for 5 years from date of installation

Supply, installation , teasting , commessoning of automatic voltage stablizer coppre wound wall mounted, singel phase with rangeof 90 -240 volt along with wall mounted brakes and fitting. the job inlluding he repairing the wall whare necessary warrantee 2 year from the date of installaion

Earthing with GI Earth pipe 4.5 mtr long 40mm dia including acessories andproviding mesonery enclouser with cover plate hasving locking arrangment and watering pipe (but wthout charcool/salt) etc as req.

Providing and fixing of IP-20 Recessde/ surface mounted round / sqaure SMD mid power (15-18 watt)LED Downlight with power coated die-cast alum. housing with UV stabilized non yellowish Diffuser withBIS complience 2.5 KV surg protected isolated driver, with short and open circuit protection .having efficiency .85% system lumin efficacy of ≥110 lm/ Watt,THD< 10%, PF ≥ 0.95, Cri.80, life time of minimum 50000 Burning Hours with 70% of intial Lumen maintained till life ends, CCT 3000°K/4000°K/5700°k/6000°/6500°K(A per ANSI Bin) , maximum power consumption should not more then the specified rating and fixture shell be of BIS standard and teade mark certificate (T.C) Manufacture word Mark / Name Engraved/Embossing/Screen Printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 &Lm80) certificate /report from OEM shall be submitted. all as per approved by EIC.

Providing and fixing of IP-20 SMD mid powerLED batten type integrted light fixture made from power coatedExtruded alum. housing with in built driver, complience 2.5 KV surg protected isolated driver, with short and open circuit protection .having efficiency .85% system lumin efficacy of ≥110 lm/ Watt,THD< 10%, PF ≥ 0.95, Cri.80, life time of minimum 50000 Burning Hours with 70% of intial Lumen maintained till life ends, CCT 3000°K/4000°K/5700°k/6000°/6500°K(A per ANSI Bin) , maximum power consumption should not more then the specified rating and fixture shell be of BIS standard and teade mark certificate (T.C) Manufacture word Mark / Name Engraved/Embossing/Screen Printing on housing. OEM must have its own in house NABL lab setup for all testing facilities for LED fixtures. (LM79 &Lm80) certificate /report from OEM shall be submitted. all as per approved by EIC. 20/22 Watt LED 4 feet with min. lumen output (2000-2200) lm

(150.1) 2X36W LED Surface Mounted

Supply and laying 1 no. PVC/XLPE insulated and PVC shealed /XLPE power cabel of 1.1 KV grade of following size in the exisiting RCC/Hume/DWC/Stone ware/metal pipe as req. 3.5 CX50 sq. mm A2XFY

Supply,installatio,teasting and commessoning of inverter 2000/2300 VA along-with 2nos. long tubler batteries 200 AH and trolly of suitable size

Supply,installation,teasting and commessoning of inverter 1250 VA along-with 1no. long tubler batteries 200 AH and trolly of suitable size