Construction of Mayor Bunglow on Mayor Bunglow Reservation Plot near Upvan Talao in Thane Muncipal Corporation Limit

Amount

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) By Mechanical Means

Excavation for foundation in hard murum including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 to 3.0m) By Manual Means

Excavation for foundation in laterite rock (soft or hard) including trimming and levelling the bed for the foundation, removing the excavated material up to a distance of 50 metres beyond the building area, stacking as directed, dewatering and back filling with available murum, watering, ramming etc. complete. (Lift upto 1.5 m.) By Mechanical Means

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30 -60 cm deep at 15 cm c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper

Labour charges for removing grass, thorney shrubs, Jungli shrub, Kubabul and alike grass along roadside making the ground clean by showel and phavaras etc. complete.

Transportation of Excavated material including loading and Unloading complete.(10km)

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting etc. complete.

Providing and laying Cast in situ/Ready Mix cement concrete in M15 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork,cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) A) Below Plinth

B) Ground Floor

C) 1st Floor

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) A) Below Plinth

B) Ground Floor

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) A) Ground Floor

B) 1st Floor

Providing and laying Cast in situ/Ready Mixcement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C.coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and applying two coats of protective membrane over the cured concrete surface like R.C.C. footings, columns, plinth beams etc. which will be submerged under soil so as to protect the same. Apply two pack coal tar epoxy system of Sunepoxy Coaltar of approved make & approved by Engineer in charge, having solid content ranges from 80-100%, Tack free time 4-6 hrs. Recoat after 16-24 hrs. Mix Part A and Part B of Sunepoxy Coaltar of approved make & approved by Engineer in charge in 1:1 ratio with slow speed stirrer and apply the same on a clean R.C.C. surface by brush. Allow to set for 8-10 hours and apply the second coat. The rate to include for application at all levels to various RCC elements to the satisfaction of the EIC etc. complete.

Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Filling in plinth and floors with approved excavated material in 15cm. to 20cm. Layers including watering and compacting etc. complete.

Providing uncoursed rubble masonry of trap / granite / quartzite / gneiss stones in cement mortar 1:6 in superstructure including racking out joints when plastering is to be done / striking joints when no plastering is to be done on inside watering and scaffolding etc.complete.

Providing flush grooved pointing with cement mortar 1:3 for stone masonry work including scaffolding and curing etc. complete.

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete

Providing Autoclaved Aerated Concrete Block masonary of conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972)

Providing and fixing chicken mesh of 22 gauge, with about 30 cm. width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /B.B.masonry and or tying by binding wire etc. complete.

Providing internal cement plaster 20mm. thick in Single coats in cement mortar 1:3 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc. complete.

Providing and applying gypsum plaster ( with Gypsum material ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete.

Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete.

Providing rough cast cement plaster externally in two coats with coloured cement finish to concrete/ brick/ stone masonry surfaces in all positions with base coat 12 to 15 mm. thick in C.M. 1:4 using gray cement and rough cast treatment 12 mm thick in proportion of 1:1 1/2:3 using colour pigment including scaffolding and fourteen days curing etc. complete.

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complet

Providing patti/ band 150mm wide on plastered surface 12 mm to 15 mm thick in C.M. 1:3 line and level including neat finishing scaffolding curing etc. complete.

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

Providing and applying Royale Luxury Emulsion of approved make on internal wall surface as detailed below Scrapping for surface with emery paper and wipe clean for area. wall primer with brush by adding mineral turpentine oil by 8 to 10 % or water by 15 to 20% allowing to dry for 6 to 8 hoursAfter applying acrylic wall putty with appropriate prpportion of water of allow to dry for period of 4 to 6 hours of activity. Scrapping with emery paper and wipe clean Applying paints Royale Luxury emulsion 1st coat with brush water content water 40 to 45% or 65 to 70% by role Applying paints Royale luxury emulsion 2nd coat with brush with water content 40 to 45% or 65 to 70 % by roller. (With prior approval of S.E.)

Providing and applying two coats Apex Ultima Puranature Anti-Pollution Or equivalent approved brand, paint should decomposes organic substances and inorganic gases(NOx, VOC’s, CO, SOx, formaldehydes, etc.) in presence of natural or artificial light. It contains Graphene and nanoparticles of titanium oxide. and Absorbs CO2 (4.8 Kilogram/15 l). plaster crack should be filled by Acrylic base Crack seal/Textured Crack filler, Paint has to applied on one coat of Apex Ultima Puranature Anti-Pollution Primer or Equivalent. Warranty Should be given by the Manufaturer The work should be done by the Manufacturer Recommended applicator and he should be able to furnish stage wise onsite technical reports from the concerned company technologist.

Designing, Conceptualization & painting of 3D artistic on any surface at all height and location as directed. The paint should be used for the artistic painting is high quality acrylic paint. painting should be coated with weather proof warnish.

Providing and Fixing Processed Stone Cladding on wall surface/ plywood surface. RCC pardi/ Wall and all type of Interior, Exterior Compound wall and Gate etc. of cladding processed stone with material of Processed clay, Wooden chips, Silica sand, Cement, GFRC admixtures, Colour pigments, Fiber up to thick of 230 mm/ 25 mm including scaffolding, fixing of screw, etc. (As directed by Engineer in Charge)

Dry wall cladding with clay tile; Designing, supplying and fixing of Clay tile of Wienerberger (Red Series or Grey Series) or Equivalent with suitable size and thickness not less than 20 mm as per manufacturer with approved colour and pattern with composition of finest powdered clay and colour mixtures. The clay tile shall be fixed on the suitable farming system by using continuous aluminium profiled section as per manufacturer with suitable size and spacing to withstand the structural design criteria specifled in the technical specification by using necessary HDG brackets, SS316 grade anchor bolts etc as per manufacturer specification. Cladding joints should be with open groove system. with prior approval of concerned Superitending Engineer.

Machine polishing to cement/marble mosaic tiled flooring or any other type of flooring including cleaning, washing, etc. complete.

P/F G.R.C sheet panels to columnade.GRC to be fabricated using cement and fine aggregate (sand) reinforced with alkaline resistancefibreglass strand.The panels are to be formed in GRC to achieve the design intent as indicated in the Architect’sdrawings and/or the approved proposed design as submitted by the contractor.Panels shall be resistant to water penetration and no dampness shall be visible on the inner face ofthe panel.The dry density of the GRCshould not be less than 1700 kg/m³

Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.

Providing and laying 18 mm thick ADONI BROWN LEATHER FINISH stone for flooring, machine cut in required size, approved shade, color and texture laid using white cement slurry over 20 mm (average) thick base of cement mortar 1:4 followed by laying, fixing and jointed with white cement slurry mixed with matching pigment, including rubbing and curing moulding and polishing to edge to give high gloss finish etc complete. The application rate for tile adhesives shall be as per manufacturer's recommendations. as per detail drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels and as directed by Engineer in charge. Complete. a) Skirting

Providing leather finished polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete.ngineer in charge. Complete. a) Skirting

Supply & Fixing of Rock / Stone Finished outdoor vitrified flooring Tiles 20 mm thick and required width wide in plain pattern including Cement float, filling joints, with neat cement slurry, Natural sand, curing and cleaning complete. with prior approval of concerned Superitending Engineer.

Provding and Laying Wooden Flooring Brazillian IPE deck / equivalent make thickness 12mm in room flooring.IS 15622:2006/ ISO 13006:2012 Group B1a. As directed by Engineer-In- Charge.On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.

Supply & Fixing of Designer Mosaic Tiles (Design and pattern to be provided as per architect) vitrified flooring Tiles

Providing and laying white marble flooring of 20 mm to 25 mm thick marble slabs laid over 20 mm thick base of cement coarse sand mortar of 1:3 and jointed with white cement slurry mixed with pigment to match the shade of stone.Design approved by architect.

Provding and Laying Brazillian IPE deck / equivalent make deck Flooring thickness 12mm in flooring.IS 15622:2006/ ISO 13006:2012 Group B1a. As directed by Engineer-In- Charge.On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.

Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader/ Paver on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- Plant Mix Method and Grading - I Material

Providing, laying and fixing exterior grade Cobble stone (size : 4" x 4" x 4") tiles for Flooring of approved colour and design in plan / designed pattern on a bed of 1:4 cement mortar including cement float ,filling joints with neat cement slurry ,curing, polishing and cleaning Cobblestone is a natural building material based on cobble-sized stones, and is used for pavement roads, streets, and buildings. Size of stone used should be 4" x 4" x 4" or 4" x 4" x 4" x 6"etc. complete. For flooring.

Providing and fixing kerbstone with led lighting system as per following specifications: dimensions with vertical mounting legs with 10mm horizontal square shape mild steel reinforcements. Illuminated kerb stone having visible dimensions :-500mm x 150mm x 150mm.(as per irc - 86-1983 ) 80mm legs having ms reinforcements shal be embedded in bt/concrete road surface.the kerb stone should have kerb angle of 45 degree, with rubber plugs at both ends of the kerbstones (2 nos)having load carrying capacity - vertical : 1465kg, horizontal : 2349 (certified by govt. Recoganized bodies)having thermal stability -: -40 to +120 degree celcius (certified by govt. Recoganized bodies. Illuminated kerb stones including : ingrace protection and connector rating ip67, electrical wire -(as per is: 694), led strip (as per lm:80) standard. Including for electrical fixing -frp junction box consisting of - 10amp. Switch module power supply(smps)having input voltage - 230v ac, output voltage 36v dc, 2 pole mcb. Illuminated kerb stones having warranty for 3 years. illuminated kerbstone shall be fixed into cast-in-situ cement concrete of m20 grade at base, back filling and grooves, including dismantling, fixing, removal of dismantled material and cleaning etc. Complete. The colour of kerb stone shall be provided as directed by engineer in charge.

Providing and laying vitrified matt fininsh tiles having size 590 mm to 605 mm x to 605 mm of 8 to 10 mm thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete.

Providing and laying vitrified rustic matt stone finish tiles having size 590 mm to 605 mm x 590 mm to 605 mm to 8 to 10mm thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete.

Adhesive Grouting For Tiles As directed by Engineer In charge

Bissaza Tiles For swimming pool As directed by Engineer In charge

Providing and laying Gangsaw granite flame /rough stone of 18 to 20 mm thick for Deck Swimming pool side flooring etc. On C.M. 1:6 including filling joints with polymer base filler nosing the sharp edges wherever necessary, curing, etc. complete.

Providing and laying polished hand cut Kotah Stone flooring 25mm to 30mm thick and 45cm to 55cm wide in plain/diamond pattern on a bed of 1:6 C.M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning complete.

Providing Mirror polishing to Kota Stone including using all necessary stones and equipments cleaning, washing etc. complete. For Flooring

Providing and fixing Modular false ceiling of 600 x 600 mm center to center and 13 mm thick square mineral fiber board to be fixed on frame work of alluminium sections for suspended false ceiling consisting of alluminium T 2”x1 ½” (50 mm x 40 mm) weighing 0.39 Kilogram/m at 60 cms center center and fixed with ½” x ½” (15 x 15 mm) flanges weighing 0.19 Kilogram/m suspended on 6 mm dia mild steel rod weighing 0.22 Kilogram/m, fixed on wall and beams including rounding of the edges with alluinium T of 2” x 1 ½” (50 mm x 40 mm) weighing 0.39 Kilogram/m etc. (all alluminium sections shall be anodized) including all labour, material, lifts etc. complete

Providing and fixing wooden ceilng of Brazillian IPE deck / equivalent make including all labour, material, lifts etc. complete.As per architect instructon.

Providing and fixing Shingles with membrane sheet (2 layers) and bison board and wooden rafters below membrane sheet as per architect.including all labour, material, lifts etc.Shingles to be installed where 2 layers ofmembrane sheet and 1 layer of biason board to beprovided. The order to be followed is first layer ofmembrane, second layer of biason board, thirdlayer of membrane and then fourth layer ofshingles to be provided. Installing shingles by abovementioned process helps in providing better waterproofing and gives roof a better architectural touch.

P/F with all accesorries complete as directed by engineer in charge.

Providing water proof bedding for flooring of Bath and WC 25 mm thick in C.M. 1:3 including using approved water proofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling, curing and covering 10 years guarantee on court fee stamp paper of Rs.500/- including ponding test etc. complete.

Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete.

Providing waterproof plaster in W.C. and bath 20 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing (and filling joints of Nahani trap and any outlet by properly) etc. complete.

Providing and applying two coats of bitumen to roof on new dungaree cloth one coat on each side etc. complete as directed.

Providing and fixing frame with / without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm with oil painting, etc. complete

Providing and fixing Country cut teak wood double or single leaf second class fully panelled door shutter with 35mm thick style and rail with 25 mm thick panels with openable fan light as per detailed drawings. Excluding the door frame 60mm x 100mm stainless steel fixtures and fastening and finishing the wood work with oil painting 3 coats. (Excluding the door frame)

Providing and fixing 34 mm thick moulded door shutter consisting of solid core single leaf flush door of 30 mm thickness lipped with 15 mm ( 5mm x 3) thick x 30 mm width on one style and top rail and 10 mm (5mm x 2) thick x 30 mm width on other style and bottom rails. The inner panels laminated with 2 mm thick termite proof, water proof and fire resistant moulded PVC sheet with 2,4,6 design in different plain and /or prelim colours on one side after routing the moulded design on flush doors and 2 mm plain and /or pre lam PVC on other side using rubber adhesive on flush door and solvent cement adhesive on the PVC lipping etc. as per direction of Engineer in charge and manufacturers specification and drawing etc. complete.

Providing and fixing fiber glass reinforced polyster door shutter 35 mm thick as per IS 14856 (2000) (Reaffirmed 2006) without ventilator including chromium plated fixtures and fastening with chromium plated handles on both sides, etc complete.

Providing and fixing M.S. grill door 24 Kilogram/ One Square Metre of various size as per detailed drawings without hot dip coating, iron fixtures and fastenings and 3 coats of oil painting etc

Providing and fixing Cast Iron Gate of various size as per detailed drawings without hot dip coating, iron fixtures and fastenings and 3 coats of oil painting etc

ACOUSTICAL WALL PANELLING – FABRIC WRAPPED OF SIZE: 600X600/1200X25MM Providing and Fixing of Acoustical Wall Panel with square edges made of fibre glass substrate 25mm thick, wrapped on the front side with an acoustically transparent fabric as per the approved shade (Husk, Copper, Sangria, Sesame, Coffee, Charcoal, Titanium, Flame, Peanut and Shell). The panel shall be classified for Fire Class A, as per ASTM E-84. The Acoustical Wall Panel shall be of sizes 600x600mm (Nominal) or 600x1200mm (Nominal) and shall achieve an NRC of 0.85 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) with 50mm airgap as per ASTM C423 to be fixed to wall on a framework of wooden battens and using Wall panel Impalers (supplied by the manufacturer) or by using construction adhesives (as per the instructions laid down by the manufacturer). The fibre glass substrate shall have a recycle content of 85%. Installation:An appropriate vapour barrier (by others) shall be applied/installed on the vertical surface before the installation to properly seal against entry of any moisture. Vapour barrier (by others) shall be installed as per Manufacturer’s recommendation. Install wooden batten grid (provided by others) of section 50x50mm or as approved by the Architect on the solid wall/partition to provide level and plumb surface. The Impalers shall be fixed to the battens using self-tapping screws, 3 nos. in case of 600x600mm and 4 nos. in case of 600x1200mm. Silica based construction adhesive (by others) to be dabbed on to the projecting elements (spikes) of the Impalers. Wall Panels shall be pierced through the spikes of the Impalers ensuring the line and level of the panels are maintained

Providing and applying melamine polish of required finish to the wood work by spray machine including knotting and preparing the even surface by scraping, applying French polish , scaffolding if required etc. complete. Note:The work to be executed on prior approval of Superintending Engineer will be necessary.

Providing antitermite treatment to the wooden frames of doors/windows of the existing building as per I.S. 6313 (Part-III) by drilling 6mm dia. holes at four corners on one side and four corners on other side at a downward angle of about 45 degree at the junction of wood work and masonary and injecting 150 ml. of chlorodane 5% W.C. and sealing by filling putty etc. complete covering 2 years guarantee on bond paper.

Sliding Window- 3 Track (2 Glass shutter + 1 flymesh) of approved make with DGU, providing and fixing of Sliding Window- 3 Track (2 Glass shutter + 1 flymesh ). For details refer to Specifications. As directed by Engineer in charge.

Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete.

Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/Square Metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete

Providing and Fixing Rollar Blinds AMI Make or approved make & shade of 38mm round Aluminium channel with Blackout fabric & telting with chain (Ball) system with all necessary fixtures and fitting etc. complete. (Sample to be final by Engineer In-charge prior execution of work)

Providing structural steel work of rectangular hollow steel section for steel trusses, other similar trussed items like purlin and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted/bolted/ welded connections and one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade complete.

Providing and fixing colour coated Zincalume ( R ) AZ150 ( min 150 gms/sq.mt. total on each side ) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 mm Base Metal Thickness ( BMT ) (0.5 mm TCT ), Hi-strength steel with min.550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminium 43.4% zinc 1.6% silicon) with COLORBOND ( R ) steel quality super durable polyester paint coat ( with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nom. 950-1050 mm effective cover width and nominal 25-30 mm deep ribs with subtle square fluting in the five pan at nominal 180-250 mm center- to-center. The end rib shall be designed for anti-capillary groove. and return leg. The feed material should have coil manufacturers product details marked a regular interval. Including fasteners with min. fastened with min. 25 um Zinc-Tin alloy coated, Hex head, self-drilling screw etc. complete. (weight of profile 4.52 Kilogram/ One Square Metre)

Providing and fixing valley gutter of 24 B.W.G. (0.63 mm) thick G.I. sheet 120 cm wide with 20 mm thick teak wood planking underneath coal tarring etc. complete.

Dewatering on BHP basis by using water pump including diversion of stream, providing cofferdams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required by using 5.0 to 9.0 BHP pump etc. complete. (prior approval of Superintending Engineer will be necessary)

Providing and fixing 50mm diameter and 1.5 mm thick vertical and top Stainless steel hand railing in S.S.304 Grade with Stainless steel square / circular pipe bracing of size 32 mm x32mm x1.5 mm in 3 rows including fabricating ,fixtures, errecting, necessary welding, grinding, finishing, buffing to stainless steel pipe etc. complete

Providing and fixing Cast Iron Railing including fabricating ,fixtures, errecting, necessary welding, grinding, finishing, buffing to stainless steel pipe etc. complete

Providing and fixing 45 cm wide mild steel ladder of 40mm x 6 mm mild steel flat stringers and steps of 18 mm dia. mild steel bar for water tank including fixing it in (1:2:4) M-15 cement concrete block 60cm x 30cm x 30cm and painting the ladder complete. (Anti Corossive Paint)

Full Height Partitions in Glass finish - Providing and Fixing 80mm to 85mm thick Full height Double Skin partition up to 3 mtr height with All visible sections in Anodized / Powdercoated finish. Made up of Frames and Tiles. Frame construction In combinaton of Aluminium Rails and Bottom ,Center and Top members, Connected with 2 way Round Shape Post , 3way Post , 4 way Post made up of Aluminium Extruded and Tiles in 5mm thk. Non Toughened Glass on both side. With all the Joints in the partitions covered with PVC extrusions to provide better sound Proofing. Tiles to be separated 55mm from each other to provide adequate space for drawing cables for electric, data and telephone with proper facility for fixing electrical and data switch plates. as per design and drawing.

Providing and fixing 50 mm. dia. medium class G.I.pipe gate with wicket gate of approved drawing with all fixtures and fittings in two leaves with strong hold fast embedded in c.c. block at top and bottom with locking arrangement including cutting, bending, making holes and with one coat of primer etc. complete.

Providing and applying priming coat over new/old steel and other metal surfaces including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and scoured with wire brushes, fine steel wool, scrappers and sand paper, scaffolding etc. complete.

Providing and applying two coats of synthetic enamel paint of approved colour to new /old structural steel work and wood work in buildings, including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) etc. complete.

Stamp Concrete of 100mm Thickness - Providing and Laying in-situ M30 Grade unreinforced plain cement stamp concrete of 100mm thickness pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate (natural sand / VSI grade finely washed crushed sand) Confirming to IS 383, as per mixed in a batching and mixing plant / non tilting mixer and weigh batcher as per approved mix design, admixtures, transporting to site in nagpur city with lead upto 20KM (on Inner Ring Road from Avasti nagar to wadi), spreading, laying with approved make pover, compacted and finished in a continous operation, finishing to lines and grades Also Providing, Placing and applying stamp powder which is light fast UV resistant pigment with appropriate chemical compounds of desired colour on base concrete after excess bleed water has evaporated using dry shake method @5kg per sqm. Including texturing, and covering with plastic sheet (min 200 micron thickness) and also applying two coats of UV-stable,30 % solids clear sealer @ 150 to 250 gms per sqm using surface roller and protecting from falling dust,dirt and curring by curring compound / by providing cement vata in cement Mortor 1 :8 @ 0.6m x 0.6m center to center, admeasuring 80mm at bottom and 40mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-incharge or Landscape architect etc. complete. (prior approval of superinteding Engineer will be necessary )

Design,supply and Installation of suitable steel structure which shall be claded with type II fabric if Mehler/Ferrari or equivalent make along with all necessary and accessories.Profiel plate will be galvanized with treaded end of make Usha martin, Anchor fasteners of Hilti,make of steel will be TATA/JINDAL or equivalent make.Test Certificate for MS will be submitted alongwith 1 year of maintenance of structure.

Providing, laying and fixing exterior grade laquered coated tiles for Flooring of approved colour and design in plan / designed pattern on a bed of 1:4 cement mortar including cement float ,filling joints with neat cement slurry ,curing, polishing and cleaning etc. complete. For flooring.

Providing and erecting 1.5 metre high wire fencing with seven rows of barbed wire supported on M.S. Angles (50 mm x 50 mm x 6 mm) at 2.5 metres centre to centre including excavating pits for foundation, fixing posts in cement concrete of size 45 x 45 x 45 cm, fastening the wire and painting the M.S. Angles with one coat of red lead primer and two coats of painting etc. complete.

Providing,aupplying,fabricating and fixing panel of aluminium composite panel cladding in approved shape made out of 4 mm thick ACP sheet material consisting of 3mm thick FR grade mineral core following NBC part IV Fire and life safety (having 2 hours fire resistance in accordance to ASTM E119-12 and BS476 part 6 and 7 class O) sandwitched between two aluminium sheets (each 0.5 mm thick of AA 5005/AA3105 grade) The aluminium composite panel cladding sheet shall be coil coated with kynar 500 based PVDF/Lumiflon based fluropolymer resin (having 70:30 ratio of PVDF and acrylic) coating of approved colour and sg=hade on top face and polymer (service) coating of bottom face as specified using stainless steel screws,nuts,bolts,washers,cleats,weather silicon sealent,backer rods etc .overall weight of the ACP shall not be less than 7.5 Kilogram/Square Metre)

Providing file storage / Cabinet of 0.45 mtr wide made up of 19mm , 12mm , 6mm ply etc. complete

Providing file storage / Cabinet of 0.6 mtr wide made up of 19mmm , 12mm , 6mm ply etc. complete

Providing & Arrangemnt of High Back Chair - TILT MECHANISM WITH MULTILOCKING, HIGH DENSITY CUSHION ON SEAT COMPOSITE LEATHER WITH METALLIC SILVER FINISH BASE AND ARMS WITH P.U.CASTORS GASLIFT FOR HEIGHT ADJUSTMENT.

Providing and Supplying Junior Engineer grade chair with cushion as approved by Engineer-In-Charge etc.Complete

supply and installation of WOODEN chair- 1'-8"X1'8"X3'-0" using sisham wood with carving works and seat of super high density foam in good quality rexine/fiber upholstery, all complete as per drawings, specification

Providing and Supplying Visitor Engineer grade chair with cushion as approved by Engineer-In-Charge etc.Complete

Executive Table @ 2250Lx2100Dx750HT including Low Height Credestal @ 1200Lx450Dx650HT Providing & Fixing of Table @ 2250Lx2100Dx750HT TOP & GABLE END to be made of Membrane finish with soft water fall edges & curved panel & Decorated Anodized section MODESTY PANEL to be made of 18 mm thick Prelaminated particle board with PVC edge band. INCLUDING CREDESTAL @ 1200L X 450D X 650H :- To be made out of Membrane Finish ( 2 Openable Shutter & 3 Drawer Pedestal in between ) as per drawing.

Conference Table @ 3600Lx1400Dx750HT Providing & Fixing of Main Table @ 3600Lx1400Dx750HT - made up of 18+18mm Thick MDF top with PVC Membrane finish and waterfall edge profile. Aluminium Anodizied finish beeding of 4mm thich is running all over the table top edge. Gable ends is Aerofoiled Shape with front edges in PVC Membrane finish and rest in Prelaminated MDF with batton structure. Gable ends should be hollow from inside for the provision of passing electrical and Data wiring. , MODESTY PANEL:- to be made of 18 mm thick Prelaminated particle board with PVC edge band Access Flap:- For Wire manager 2 Nos.

Full Height Steel Storage @ 750Lx450Dx2100HT Providing and fixing Openable Steel Storage of 750 x 450 x 2100Ht, with 4 adjustable shelves, Complete body & shutter made in 0.8 mm thick & Top in 2 mm thick CRCA, 4 Shutter to be mounted with the help of cup hinges, and 4 adjustable levelers, enitre storage in powder coated finish with 60 to 80 microns as as per drawing.

Multiple Compartment Lockers @ 1140Lx 457D x 1830 mm. Ht. Providing and fixing Multiple Compartment Lockers @ 1140Lx 457D x 1830 mm. Ht. with 12 Compartments , Complete body & shutter made of CRCA Sheet with powder coated finish as per approved color.

Sofa Set 3+1+1 Providing & fixing Sofa Set 3+1+1 Brown and Cream leather DIMENSION Length: 182.5 (cms) Breadth (cms): 100 (cms)Height (cms): 100 (cms) Weight (Kilograms): 66 (Kilogram) Seating Capacity: Five Seat

Kitchen Trolley Providing and Fixing stainless steel kitchen trolley of overall 26 " height and 22" depth,supported on aluminium pipes ,trolley basket made out of 5 mm stainless steel rod fitted on telescopic channel of size 1.5 " x 20 " x 22 " on both sides of trolley of 12 " or above size, panel having 40Kilogramload bearing capacity of trolley made out of 20 mm PUC coated plywood and colour combination as directed by E-I-C.Inner side of panel covered by white mica ,100 mm s.s. decorative handle.(The width and height of individual compartments shall be kept as directed by Engineer-in-charge)

Providing and fixing Facility Building Outdoor Signages LED Made Of MS Febrication Hording & bracket &Supplying & Fixing of 4 mm X 0.50 foil Aluminum Composite Panel With 38mm X 25mm Aluminum Tube Framing, 12mm X 1.5mm Spacer Tape, Dow Corning Silicon Sealant . As per your Instruction.

Providing and Fixing Steel or Acrylic Letters with LED Made Of MS Febrication Hording & bracket

Providing and Fixing Acrylic TMC Logo

P&F all Irrigation systems required for garden works such as Installation of Irrigation system with pump provided with rigid pvt pipings, roters, sprinklers, nole & other accessories, etc. compl=ete as directed by engineer in charge.

P&F Filteration Plant for swimming pool.

Providing detailed geological reports of proposed site by maintaining geotechnical investigation of structure stratification collecting soil, rock and ground water samples for laboratory tests to arrive the foundation design parameters . Rock properties such as type of rock, jointing fractures, etc. complete with suggestion about the site foundation and remedies.

Soil Test - Complete Soil test with 2 Bore logs, etc. complete as directed by Engineer in charge.

Concrete Tests - Compressive Strength OF C.C. Cube (Set of 3 cubes).

Steel Tests - Upto 16 mm (Set of 3 Bars)

Brick Tests - Water Absorption (Set of 5 Bricks), Compressive Strength( Set of 5 Bricks), Efflorescence (Set of 5 Bricks).

Tile Tests - Water Absorption, Modulus of Rupture (Set of 6 Tiles)

Crane 80 tonne capacity

Excavator (JCB JS 80 ) 0.90 Cu.M capacity

Providing and Fixing Falling star Gemstone Chandelier. Double height Chandelier with modern light fixture for hotel, Showroom, Enterance for home décor- dia: 5ft & height: 4-5 ft (chrome plate) Amber stone.

Providing and Fixing MANSNIX motorized blinds with valance remote control upgraded smart blackout roller shades electric automatic blinds for window blinds and shade (white width: 46 inch X height : 72 inch)

Providing and Fixing Premium printed blackout opaque cutain with lining.

Providing and Fixing Curtain of LOHA Linene Grommet top window cutain panel pair. ( Width: 54 inch & Length: 96 inch)

Providing and Fixing Classic wood and Craft Dining table set in 8 chairs in luxurious front- carving/heavy dining table/Luxurious Dining set / 8 chairs dining set/ Dining table 8 seater.

Providing and Fixing white statuario Italian marble flooring 20mm thickness.

Providing and Fixing Maxima 12 feet meeting table in leather and wood.

Providing and Fixing Marshal wall art wallpaper AFL KM 1007 600mm X 600mm size.

Providing and Fixing Marshal wall art wallpaper Florals PS 301 size 1.05 mtr X 5 mtr roll

Providing and Fixing johson or equivalent make marbonite flooring tiles of size 600mm X 600mm.

Providing Single Seater Sofa(Type-i) for commonroom of size 2’- 7”(L)x2’-0”(W) x 2’-7” (ht) with basic framework made in first class Hollock/Mirandi wood (kiln seasoned and chemically treated,), the base for sofa cushions to be made a layer of steelSprings uniformly distributed across the length and breadth of sofa framework supported on frame of hillock wood and base of ply and jute layer , gaps to be filled with coir of foam fillers and top layer to be made of a class jute sheet encompassing min. 50mm foam (Sleepwell/Kurlon make).This layer in turn shall be finished with A- class Molfino fabric (Ddecor or equivalent make)(color and texture as approved by NIB) with sewn seams to be multi top stitched. The seat shall have 150mm thk.(minimum) removable cushions placed on the finished seta, which shall be duly upholstered with A-class molfino fabric (Ddecor or equivalent make) (color and texture as approved by NIB), fixed with a zipper on lower side (for ease in maintaince cleaning)..

Sofa Three Seater: Providing Three Seater Sofa (Type-i) of minimum size (6'-8"(L) x 2'-4"(Depth) x 1'-9" ( seat height.)x2'7"(fixed back rest) with removable cushions (back rest) with basic framework made in first class Hollock/Mirandi wood (kiln seasoned and chemically treated,), the base for sofa cushions to be made a layer of steel Springs uniformly distributed across the length and breadth of sofa framework supported on frame of hillock wood and base of ply and jute layer, gaps to be filled with coir of foam fillers and top layer to be made of a class jute sheet encompassing min. 50mm foam (Sleepwell/Kurlon make).This layer in turn shall be finished with A- class Molfino fabric (Ddecor or equivalent make)(color and texture as approved by NIB) with sewn seams to be multi top stitched. The seat shall have 150mm thk.(minimum) removable cushions placed on the finished seta, which shall be duly upholstered with A-class molfino fabric (Ddecor or equivalent make)(color and texture as approved by NIB), fixed with a zipper on lower side (for ease in maintaince cleaning)..

Providing and Fixing Bathtub of Jaquar or equivalent make of zie 1800 X 1100 X 480 mm in size with all fitting and fixtures.

Automatic sliding door system having maximum opening 2000/2x2.100 mm, maximum weight of the door is 70-80 Kg, DC 24V 60W herical gear motor, 55-60 DB noise level, built-in motor lock and ( DORMA/OZONE) with all necessary handle, fixing ,patches, including locks at bottom side etc.

Providing and Fixing woodshastra teakwood velvet fabric king size chair golden beige colour (size 30 inch X 37 inch)

Supplying and fixing of 15mm Toughened glass partition with profile channel of top & bottom patch fitting

Providing and Fixing Madonna Rectangular Multisystem Steam Bath - Atlas (6"X 4'), WhiteA specially designed multisystem which combines Sauna and Steam Bath systems for a unique experience. Product and Design Feature : Sauna Bath, Steam Bath, Intelligent Panel, Water Faucet Inlet, Multi Functional Sprinkler, Paddle Discharge Controller, Hydrodynamic Adjust, Computerized Radio Tuner, Telephone Answer, Backside Light, Temperature Display/ Adjust, Overhead Sprinkler, Sprinkler Shift, Overhead Light, Exhaust Fan, Control Panel, Cosmetic Mirror

Providing and supplying Automatic or Motorized treadmills In gymnasium , the device provides a moving platform with a wide conveyor belt driven by an electric motor or a flywheel Spec- As Directed Engineer-In- Charge.

Providing and supplying Adjustable training bench in gym Spec- As Directed Engineer-In- Charge.

Providing and supplying dumbbell Bodyfit 30Kg Gym 4-In-1 Multi Leg Curl Bench Home Gym Dumbbell Set 30Kg Weight Plates: 2.5 Kg x 4 = 10 Kg + 5 Kg x 4 = 20Kg 4In1 Bench, 1X5Ft Rod, 1X3Ft Curl Rod, 2X14Inch D.Rods or equivalant Spec- As Directed Engineer-In- Charge.

Providing and supplying kettle bell set Spec- As Directed Engineer-In- Charge.

Providing and supplying pull up frame and bar Spec- As directed Engineer-In- Charge.

Providing and supplying Stationary bicycle Spec- As Directed Engineer-In- Charge.

Providing and supplying elliptical machine Spec- As Directed Engineer-In- Charge.

Providing & Supplying Leg Curl / Leg Extension Spec- As Directed Engineer-In- Charge.

Providing & Supplying Seated calf Spec- As Directed Engineer-In- Charge.

Providing & Supplying Adjustable decline benchSpec- As Directed Engineer-In-Charge.

Providing & Supplying Squat rack Spec- As Directed Engineer-In- Charge.

Providing & Supplying Power cage Spec- As Directed Engineer-In- Charge.

Providing & Supplying Leg press Spec- As Directed Engineer-In- Charge.

Providing & Supplying Doumble rack. Spec- As Directed Engineer-In- Charge.

Supplying and installation of gym rubber flooring with a thickness between 10 to 50 mm top 5 mm layer of the surface rubber tile pigmented with 0.8 to 2 mm crumb rubber granules and polyurethane polymerically bonded ASTM and DIN standard approved. hardness A60 (ASTM D2240), Tensile strength 1.29 (DIN 53304 Force 55.4 N), elongation break 47% (ASTM D573). Tear strength 40.1% strain @break,specific gravity 0.88, compression set 7.23 Mpa, operating temperatures 140-150 degree celsius . UV Exposure (150*C) by chemical analysis ISO 4 SBR Blend rubber no effect. ASTM 0.45 noise reduction coefficient (NRC), ASTM D2859 Pill flamability excellent pass. ASTM E30393 Skid resistance excellent pass.

Providing and fixing orissa type colour glazed earthenware 625 x 450 mm. w.c. pan including trap, C.I. soil and vent pipe upto the out side face of wall including 100 mm. dia. C.I. plug, bend, 15mm. thick 10 litre PVC flushing cistern with all necessary pipe connection etc. complete.

Providing and fixing white european type wall-hung pan, of size 350mm x 355mm x 570 mm concealed flush tank with floor-mounting frame installing kit and drain pipe connection set for wall hung WC, with approved make square control plates including soil pipe, vent pipe upto the outside face of wall, 100mm dia C.I. plug bend inlet pipe all fittings,cutting & making good walls, floors etc. complete.

Providing and fixing white glazed urinal of size 710x460x300mm with sensotronic concealed type flushing valve for urinal with complete kit having fittings, inlet pipe with stop tap, brackets for fixing the cistern, 32mm diameter P.V.C. flush pipe with fitting and flushing arrangement including lead soil pipe, lead trap & soil pipe connection upto the outside face of wall etc complete.

Providing and fixing on walls/ ceiling/ floors 20 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 1.93 Kilogram/meter with necessary fitting remaking good the demolished portion and applying primer of anti-corrosive oil paint, 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floors 25 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 1.93 Kilogram/meter with necessary fitting remaking good the demolished portion and applying primer of anti-corrosive oil paint, 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floors 50 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 1.93 Kilogram/meter with necessary fitting remaking good the demolished portion and applying primer of anti-corrosive oil paint, 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floors 80 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 1.93 Kilogram/meter with necessary fitting remaking good the demolished portion and applying primer of anti-corrosive oil paint, 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing 20 mm dia. screw down bib/ stop tap of brass including necessary socket union nut complete.

Providing and fixing 25 mm dia. screw down bib/ stop tap of brass including necessary socket union nut complete.

Providing and fixing Table top white wash basin of size 120x635x405mm rubber plugs and brass chain, with pillar cock, C.P.Angular stop cock long thread, continental including S.S. bottle trap of approved make having necessary pipe connection up to theoutside face of the wall.etc complete as directed by Engineer in charge.

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Providing and laying for 225mm dia. salt glazed S.W. Pipe including fitting such as bends, tees, single junction, double junctions laying, jointing (including excavation and refilling the trenches) complete

Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete.

Providing and constructing Brick Masonry Inspection Chamber 90cm x 45cm With R.C.C. raft in B.C. soil area including cost of reinforcement, 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and airtight with 75 mm thick R.C.C. cover medium duty 140Kilogrametc. complete.

Providing and fixing reinforced cement concrete cover of size 90 cm x 45 cm with frame over inspection chamber etc. complete. Heavy duty (225 Kilogram)

Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete.

Providing and fixing P.V.C. Rain water pipes of 160mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592- 1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Providing and laying in trenches 80 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 10.15 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and laying in trenches 100 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes of 10.15 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclusive of all tanks capacity between 200 to 1000 liters

Providing and fixing divertor with overhead shower,shower arm,spout,hand shower with wall bracket having flow rate up to 12 liters/minutes of Jaquar/Cera/Hindware /Perryware or equivalent make including all necessary pipes,fittings etc.complete as directed by Engineer In Charge.( Make shall conform to manufacturer's Green product and shall got approved from the Engineer In Charge.)

Providing and fixing 450mm x 550mm size superior type Belgium mirror with 16mm dia. nickel plated towel rod etc. complete.

12"SS Handle: (For 2 Hr fire Rated 12"SS Handle) Supplying, fitting & fixing Stainless Steel 'D' or 'H' type of size 300 mm x 19 mm tubular Handle with Grade 304, CE certified, marked & conforming to EN - 1154 of approved quality (Internationally reputed brand like Dorma, Geze, Hafele, Assabloy & Magnum etc.)as per direction of Eingineer -in Charge fitted and fixed complete including all taxes & incidental charges.

Providing and fixing chromium plated towel rod 16 mm dia and 75 cm. in length including all accessories complete.

Excavation for planting lawn/ shrub/ flower bed/ hedges/ edges/ canna bed in earth, soil of all types, soft murum, including removing the excavated material up to a distance of 50 mtrs. for a depth of 30 cms. Rate= Rs.71.70 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23Sr No.3)

Supplying on site fresh Garden soil (free from stones rubbish like dried grass roots, other such materials) for excavation area of depth of 30 cms.( consolidated thickness). Rate= Rs.391.50 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23 Items of garden work,Sr No.36a)

Supplying on site well decomposed Farmyard Manure for excavation area of depth of 30 cms. (Consolidated thickness). Rate= Rs.125.55 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23Sr No.36b)

Mixing garden soil/silt & manure thoroughly well, watering previous night. Planting reqired plant species, lawn grass as directed etc. complete for required depth 30 cms. for planting lawn/ shrub/ flower bed/ hedges/ edges/ canna bed/ ground cover. (1/10 of semiskilled labour) Rate= Rs.77.76 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23 Sr No.23)

Filling fresh garden soil / silt & manure in excavated area of depth 30cms. Add-Increased in percent for Corporation Areas @ 5% Rate= Rs.27.02 (As per Parks and garden, PWD Government of maharasthra DSR 2022-23 Sr No.13)

Providing on site well established (free from weeds /disease etc.) ready to fix lawn turf in slabs/ rolls of required variety as directed. Rate= Rs.215.00 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Sr No.47)

Preparing Instant Lawn : Excavating the ground to a required depth of 20cms removing & conveying unwanted stuff to a required distance as directed. filling fresh garden soil / silt & manure in excavated area in 3:1 proportion to a height of 20cms. Mixing garden soil and manure thoroughly will levelling, watering on previous night. Planting required variety of lawn grass as directed and maintaining till well established by watering weeding clopping rolling etc.

Tagar (Bag Size 9"x11", hight of plant 20 cm to 45, cm) Rate - Rs. 55 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 13)

Duranta golden Well Developed, Healthy Foliage / Half Bloom Stage , Free from Pest and Diseases. (Bag Size 8" x 10"", hight of plant 30 cm to 50, cm) Rate - Rs. 42 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 27 , 7(b) Hedges item No 3)

Malphigia (Bag Size 10''10", hight of plant 45 cm to 60, cm) Rate - Rs. 45 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 20 , 1 (b)Flowering Shrubs item No 20)

Canna Dwarf (Bag Size 7"x8", hight of plant 30 cm to 45, cm) Rate - Rs. 20 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 21, 4.Bulbus/Rhizomatous plants item No 3)

Mini Ixora (Bag Size 8"x10", hight of plant 30 cm to 45, cm) Rate - Rs. 55 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 17 , 1 (b)Flowering Shrubs item No 8)

Alpinia (Bag Size 13"x13", hight of plant 3 to 4 feet, ) Rate - Rs. 205 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 19, 2(b)Foliage Shrub item No 2)

Thuja (Bag Size 13"x13", hight of plant 45 cm to 60cm) Rate - Rs. 206 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 20, 2(b)Foliage Shrub item No 21)

Fox tail palm (Bag Size 21"x21", hight of plant 9 feet and above) Rate - Rs. 2100 Add-Increased in percent for Corporation Areas @ 5% (As per Parks and garden, PWD Government of maharasthra DSR 2022-23,Page No 36, 11(e) Palms item No 3)

Unskilled Heavy Labour

Mali Skilled Labour

Maintenance of Garden Landcape Area (Including soil, Fym & Labour)

Supplying and laying HMS PVC conduit FRLS grade 20 mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying and laying HMS PVC conduit FRLS grade 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying and laying HMS PVC conduit FRLS grade 32mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.

Supplying and erecting 25 mm dia. corrugated flexible polypropylene conduit

Supplying and erecting PVC box trunking of size 50x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying and erecting PVC box trunking of size 75x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX.

Supplying and erecting PVC box trunking of size 100x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX .

Supplying and erecting PVC slotted box trunking of size 45x30 mm. with accessories on wall/ceiling as per specification No: WG-MA/SLBOX.

Supplying and erecting PVC slotted box trunking of size 100x100 mm. with accessories on wall/ceiling as per specification No: WG-MA/SLBOX.

Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting mains with 3x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting mains with 3x6 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting PVC insulated PVC round sheathed 4 sq.mm (56 no. x 0.30 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch one way 16 / 20 A, duly erected on provided plate and box with wiring connections complete with neon indicator.

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type bell indicator, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type buzzer 220 / 250V, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type blanking plate one module, duly erected on provided plate & box.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 1 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 4 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 16 / 18 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and erecting modular pop up Box 8 module erected with provided AV/ HDMI , RJ 45,6 A electrical sockets and switch on provided table.

Point wiring for light/bell concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/CW

Point wiring for ceiling fan concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/CW

Point wiring for light/bell hybrid type (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/HW

Wiring for plug on board with switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification no. WGPW/ CW

Supplying and erecting LED square / circular Max. 7W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 770 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED square / circular Max. 11 W down lighter/Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 1200 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED square / circular Max. 14 W down lighter/Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 1500 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED square / circular Max. 18 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED square / circular Max. 25 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2750 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED Panel Light(600mm X 600mm) Max. 30 W having CRCA powder coated housing, polystyrene diffuser having system lumens output of Min. 3600 Lumens, min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED Panel Light(600mm X 600mm) Max. 35 W having CRCA powder coated housing, polystyrene diffuser having system lumens output of Min 4200 Lumens, min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Supplying and erecting LED Strip light 5m Length Max. 45 W IP20 class having minimum lumens output of 800 Lumens/m, min. efficacy of 90 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD<10%, p.f. >0.95, operating range of 230-270V, Life class of 30,000 Hrs. at L70B50, including driver with 1 year warranty.

Supplying and erecting anodized aluminium corridor / passage / mirror light LED fitting (2 feet) Max. 12W with high transitivity diffuser with min. system lumens output of 1200 lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying and erecting CRCA powder coated corridor/passage light LED fitting (4 feet) Max. 17W with high transitivity diffuser with system lumens output of Min. 2000 lumens , min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying and erecting CRCA powder coated corridor / passage light LED fitting (4 feet) Max. 33W with high transitivity diffuser with system lumens output of Min. 4000 lumens , min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying and erecting CRCA powder coated corridor / passage light LED fitting (4 feet) Max. 50W with high transitivity diffuser with system lumens output of Min. 6000 lumens , min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying & erecting inverter LED batten 20W tube light fitting with polycarbonate housing, heat sink, integrated HF electronic driver, Min. 2600 mA Lithium ion Battery with charging time of 8-10 Hours and backup time of Min. 3 Hrs with minimum 25% of initial Watts having luminous efficacy of 100 lumen/watt, CRI>80, CCT of 6500K and THD<=20 % having useful life of minimum 25000 Hrs with over heat protection with minimum 2 years as per specification No. FG-IDF/LED.

Supply Installation Testing & commissioning of Integral high pressure Die cast/extruded aluminum LED Streetlight luminary the system wattage (fixture's total power consumption)should be 90W +/- 5 Watt Details as per technical specification attached.

Supply Installation Testing & commissioning of Integral high pressure Die cast/extruded aluminum LED Streetlight luminary the system wattage (fixture's total power consumption)should be 60W +/- 5 Watt Details as per technical specification attached.

Supplying and erecting integrated LED Bollard Cylindrical/Cubical shaped 800mm 8W IP65 & IK10 class having extrusion aluminium housing with polycarbonate diffuser, having system lumens output of Min. 800 Lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-240V, inbuilt surge protection of 2 kV, Life class of 25,000 Hrs. at L50B50, including driver complete with 2 Year warranty as per specification No FG-ODF/FLS2.

Supplying and erecting integrated LED Post Top 45W IP65 & IK10 class having die cast aluminium housing with UV protected polycarbonate diffuser, having system lumens output of Min.4500 Lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-240V, inbuilt surge protection of 2 kV, Life class of 30,000 Hrs. at L50B50 , including driver complete with 2 Year warranty as per specification No FG-ODF/FLS2.

Supply and erection of BREEZA type decorative hot dip Galvanized single arm bracket of 1 Meter long made from 48.3 mm OD pipe, min 3 mm thick with cross support of 33.7 mm OD pipe, min3 mm thick with cap pipe length of 0.450 Meter suitable for Oct pole with top of 70 mm, with 4 Nos bolts. The Bracket shall be capped with suitable decorative STEEL/FRP ball duly bolted/ welded. The tilt angle shall be 10 to 12 degree as directed by Engineer - in - charge. BREEZA type bracket or its equivalent as per the drawings enclosed.

Supplying and erecting bracket fan 400 mm. sweep A. C. 230 volts 50 cycles 1350 RPM. Oscillating type, plastic or metal blades chrome plated guard with speed regulator and moisture proof treatment to winding and with ‘E’ class insulation.

Supplying and erecting Energy Saving Ceiling fan of 3 star rating as per BEE 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Supplying and erecting fan hook box of 10 mm M.S. round bar bounded to the R.C.C. bars upto 50 mm length each side and pierced through a 16 S.W.G. thick aluminium/M.S. Bowl 100 mm dia. or equivalent square size and having depth upto 75 mm complete erected with duly painted by one coat of red oxide paint and two coats of paint erected in position and without any leakage of slurry of cement concrete on either side of the box and positioned to the bottom level of the slab.

Supplying and erecting ‘B’ class G.I .pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire.

Supplying & erecting 20 SWG G.I sheet metal cawl rectangular / round shaped with 25 x 25x 3 (mm) angle iron frame, metal mesh to avoid birds entry with necessary material, suitable for exhaust fan of 300 mm as per specification no FG-FAS/MSC

Supplying, installing, testing and commissioning of 2500 VA Digital pure sinewave inverter based on Insulated Gate Bipolar Transistor (IGBT) technology single phase 230V,50 Hz complete as per specification no. AP-INV (Without batteries)

Supplying, erecting, testing and commissioning of 10kVA capacity online pure sine wave, with backup time of 0.30 hrs. PWM & IGBT based UPS with 0.9 to unity output pf, 3 phase input & 3 phase output complete with all protections as per specification no. AP-UPS

Supplying and erecting 12V/100Ah tubular battery with battery terminal wire, duly charged with 36 months warranty complete.

Supplying and erecting 12 V/65Ah SMF battery with battery terminal wire, duly charged complete with 24 months warranty complete

SITC of street light control panel inclusive of all electrical accessories mentioned in tender document with quartz electronic time switch

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 40A to 63A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking DPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking DPMCB 6 A to 32 A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking DPMCB 40A to 63A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking DPMCB 40A to 63A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking TPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking TPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking FPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 4 ways/phase (12 poles), with door, 1.2mm thickness, surface/flush mounted, IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 8 ways / phase (24 poles), with door, 1.2mm thickness surface/ flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 12 ways /phase (36 poles), with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 4 ways /12 Poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 8 ways /24 poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying & erecting triple pole and neutral distribution board (TPNDB), SP/TP MCBs total 12 ways /36 poles, with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB

Supplying & erecting CRCA sheet metal enclosures of 1.2mm thickness with 20A, 2 pin plug & earth socket and 20A, 3 pin plug top with 20A/30A single pole MCB having rated short - circuit breaking capacity (Icn) 10kA complete erected on angle iron/ GI frame.

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole/ 4 pole MCCB as incomer & outgoing SP MCB (12 poles) or TP MCB of 4 ways (12 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB1

Providing & erecting 3 Pole MCCB, 415V, 200A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB Note:-As per Foot Note For use of 4 pole MCCBs in place of 3 pole MCCBs add 20% in rate of 3 pole MCCB.

Providing & erecting 3 Pole MCCB 415V, 250A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB Note:-As per Foot Note For use of 4 pole MCCBs in place of 3 pole MCCBs add 20% in rate of 3 pole MCCB.

Supplying, erecting & commissioning 2 pole RCCB 16/25A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB

Supplying, fixing and commissioning 2 pole, RCBO 6/10/16/20/25A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO

Supplying, fixing and commissioning 2 pole RCBO 32/40A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO

Supplying, fixing and commissioning 2 pole RCBO 63A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO

Supplying, fixing and commissioning 4 pole RCBO 6/10/16/20/25A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indications per specification no SW-RCCB/RCBO

Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Supplying, erecting, testing & commisioning 50 kVAr, 3 phase, 50 Hz., APFC Panel with derated power contactor of suitable rating for capacitor switching Application for each step controlled by microprocessor based APFC relay consisting of 2,3,3,5,5,7,10,15 or suitable steps of MPP /APP type capacitor with 525 V and having minimum overcurrent capacity of 1.8 In, peak inrush current capacity 300 In and minimum life 150000 hours with detuned aluminium wound reactor of 7/ 14% for each step, APFC Panel shall suitable rating MCCB as incomer and each branch/step shall have separate isolation with MCCB/MCB of Suitable rating for protection, compliance to IEC 61439 and power quality IEC 61921 standard as per specification no. CP-ED/APFC.

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 35 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 50 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 120 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 150 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 185 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 5 %

Supplying, erecting & terminating XLPE insulated unarmoured cable 1100 V. 1 core 25 sq. mm. copper conductor complete erected with provided lugs, laid in provided control panel /distribution boards / pipe as per specification no. CBLT/ CU Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 2 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 2.5 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 2 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 2 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 2 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 2 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 2 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 2 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 2 %

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU Note :- For use of FRLS-XLPE insulation instead of FR-XLPE insulated armoured cable increase rates by 2 %

Supplying & laying (including excavation) reinforced cement concrete pipe of IS 458:2003 NP-2 class of 150 mm internal diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.

Supplying & laying (including excavation) reinforced cement concrete pipe of IS 458:2003 NP-2 class of 250 mm internal diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 90 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 120 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Supplying and laying (including excavation of suitable width & depth up to 90 cm)160 mm outside dia, double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, complete.

Supplying & erecting water tight terminal box of 1.6 mm (16 gauge) CRCA sheet of size 200 x 150 x 150 mm. complete on pole as per specification No. CB-SB

Supplying & erecting crimping type copper lugs for cable up to 16 sq mm complete as per specification No. CB-CL/CU

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 100 mm height comprising all required standard accessories.

Providing & erecting hot dipped galvanised Perforated type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware.

Providing & erecting hot dipped galvanised Perforated type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 200 mm width & 75 mm height complete with necessary coupler plates & hardware.

Providing & erecting hot dipped galvanised cover suitable for perforated type Cable tray manufactured from 18 SWG (1.2 mm thick) GI sheet of 150 mm width & 20 mm height complete with necessary hardware.

Providing & erecting 7 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Providing PU paint to octagonal poles as required of desired colour duly finished in an approved manner for 7 mtr long pole

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover complete with all materials, testing & recording the results as per specification no. EA-EP

Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP

Supplying, installation and testing of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete, and recording the results Specification no. EA-MOBI

Supplying and erecting copper strip of high purity required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint with joints required. As per specification no. EA-EP.

Supplying and erecting annealed bare copper wire of high purity of required sizes used for earthing on wall with necessary copper clamps fixed on wall/cable/conduit with screws complete.

Supplying and erecting copper strip of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with insulating and non-corrosive bond with required joints As per specification no. EA-EP.

Providing and back filling ground enhancing compound 25 kg bag complete.

Providing printed instruction chart for treating persons suffering from electric shock, printed in English & Marathi and duly laminated complete.

Providing pair of duly tested rubber hand gloves as per IS :47705 suitable for working up to 22 kV supply complete.

Supplying standard first aid box with necessary antiseptic cream, medicine for use on wounds due burn, crepe bandage, gauge bandage, medicated ready to use bandage (Band-Aid) adhesive tape for medicinal use, scissors, anti-septic solution, etc. (All above contents shall be of standard makes)

Supplying and fixing PVC synthetic elastomer electrically insulating mat with class B insulation conforming to IS: 15652 – 2006 having 2.5 mm thickness up to 11 kV

Supplying SMC chequered plates of size 4ft x 2ft, hot press moulded from advanced composites of plastics namely sheet moulding compound of thickness 2.5 mm with insulation level up to 22 kV and fixing it to substation floor with SR-998 adhesive along with 5 mm thick E.P. foam complete.

Supplying, erecting, testing and commissioning of diesel generating set with alternator of 140 kVA output continuous rating, 3 phase, 415 V, 50 Hz, 0.8 p.f., A.C. supply, a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %, with performance class G2/G3 and maximum fuel consumption 22.85 ltr/hr @75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads, with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete set nclosed in composite acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA sheet, sound absorbing material to restrict sound level up to 75 dB at 1.0 m, provided with first filling of oil, diesel not less than 290 ltr etc., on provided M20 grade CC foundation as per specification no. GEN-DG

Supplying, erecting, testing and commissioning of microprocessor based AMF panel suitable for diesel generating set of above 140 kVA upto 180 kVA capacity 3 phase, 415 V, 50 Hz, A.C. supply with all standard features, safeties etc as per specification no. GEN-AMF. Each 156644 11-2-14 Supplying, erecting, testing and

Making trench in soft soil having 0.75 m depth and minimum 0.3 m width for laying provided cables up to voltage level of 1.1kV complete As per specification No. CW-EXN-CTR

Making trench in Hard murum/Tar road having 0.75 m depth and minimum 0.3mtr width as per IS for laying provided cables up to voltage level 1.1Kv cable complete as per specification No. CW-EXN-CTR

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole).

Supplying and erecting mini feeder pillar with 415V, 200A FP MCCB as incomer and 2 outgoing circuits with HRC fuse base and cartridge of 100A with aluminium bus bar erected in 14 SWG CRCA sheet box with supporting angles, self locks, gasket and enclosure must be dust proof, rust proof, vermin and water resistant, having slanting top and erected on angle iron/ GI frame in provided C.C. foundation complete as per specification no. SW-MFP.

Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 900 mm, Max. Energy Consumption of 28W having service ratio (CMM/W) of Min. 8, PF>0.9, THD<10% with IR remote control, Temperature Rise of Max. 40 deg.C, having external mounted control PCB completely erected in position as per specification no. FG-FN/CF.

Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 mm, Max. Energy Consumption of 28W having service ratio (CMM/W) of Min. 8 , PF>0.9, THD<10% with IR remote control, Temperature Rise of Max. 40 deg.C, having external mounted control PCB completely erected in position as per specification no. FG-FN/CF

Providing & erecting 3 Pole MCCB, 415 V, upto 100A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB Note:-As per Foot Note For use of 4 pole MCCBs in place of 3 pole MCCBs add 20% in rate of 3 pole MCCB.

Providing & erecting 3 Pole MCCB, 415V, 160A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no lineload bias in provided enclosure/panel as per specification no. SW-MCCB As per Foot Note For use of 4 pole MCCBs in place of 3 pole MCCBs add 20% in rate of 3 pole MCCB.

Providing & erecting 3 Pole MCCB 415V, 400A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure /panel as per specification no. SW-SWR/MCCB Note:-As per Foot Note For use of 4 pole MCCBs in place of 3 pole MCCBs add 20% in rate of 3 pole MCCB.

Supplying & erecting porcelain/epoxy bus bar support complete erected in provided M.S. box for 200/300A

Supplying & erecting porcelain/epoxy bus bar support complete erected in provided M.S. box for 400A

Supplying, erecting, testing & commisioning metal work in CRCA sheet including Iron work for supports with fabrication of boxes, panel boards, etc. including cutting, bending, drilling, welding, riveting, treated with anti-rust treatment and painted with one coat of red lead paint and 2 coats of enamel paint or powder coating complete as per specification no. CP/SH/CR

Supplying, erecting, testing & commisioning of any size electrolyte aluminium patti or bar in bus bar chamber / in panel or any other purpose, 500 V with require capacity 99.9% aluminium purity with E91E Grade as per IS 5082 & current density 0.8 A per sq mm with fixing arrangement (like lug or bottle type lug) to both the end with high grade polyolefin insulation sleeve complete as per specification no. CP-BB

Supplying and erecting panel mounting type digital ammeter having three and half digit LED display, external CT operated, calibrated for suitable to operate on 500V, 0 to 1000A having accuracy class of 0.5, AC supply with necessary PVC wire leads and lugs and mounting hardware on provided panel complete with calibration certificate from manufacturer.

Supplying and erecting panel mounting type digital voltmeter having three and half digit LED display, calibrated for 0 to 750V AC suitable to operate on 500V having accuracy class of 0.5, AC supply with necessary PVC wire leads and lugs and mounting hardware on provided panel complete with calibration certificate from manufacturer.

Supplying, erecting, testing & commisioning LT current transformer with bar primary 50/5 to 1000/5 ratio with 15 VA burden erected in provided CRCA box duly secured with insulating materials connected to the meter with test certificates.

Supplying & erecting LED type indicating pilot lamp with LED colours red / yellow / green, 230/250V on provided box / panel with necessary material, wiring & connections etc.

Supplying & erecting LED type indicating pilot lamp with LED colour blue, 230 / 250 V on provided box / panel with necessary material, wiring & connections etc.

Supplying and erecting terminal spreaders suitable for 3 pole, upto 100A MCCB (set of 6)

Supplying and erecting terminal spreaders suitable for 3 pole, upto 250A MCCB (set of 6)

Supplying and erecting terminal spreaders suitable for 3 pole, upto 400A MCCB (set of 6)

Supplying double door refrigerator domestic type of minimum litres storage capacity, minimum 415 litter 5 Star inverter type, stabilizer free operation suitable for operation on 100V/300 V, 50 cycles complete with automatic temperature control, shall be marked on unit for sealed unit in refrigeration system and marking sr. no. and date of erection.

Supplying and erecting storage type water heater 25 litres capacity having standing loss < 0.465kWh/24hour/45°C, high impact resistance engineering plastic body with anti corrosive high grade steel inner tank, heating element having hard water & corrosion protection, with minimum 3 safety protections (i.e. thermostat & thermal function valve) complete with 3 core PVC flexible wire leads complete & total pressure 8 bar withstanding capacity duly tested and marking sr. no. and date of erection complete as per specification no. AP-WH/STWH

Supplying, installing, testing and commissioning of 100 kWp ON-GRID Solar pV System / Plant consisting Solar PV Poly Crystalline Panel (335 Wp X 300 Nos.) and Solar ON-GRID Inverter of similar capacity (THD<3%) with interconnecting wires / cables up to solar ON GRID inverter, proper base plate, canopy box to house Inverter and necessary cessories i.e. ACDB/ DCDB , MCB etc. wiring up to solar Inverter in casing and capping, display board, sign board, two distinct earthing, lightning arrester, liasoning charges, remote monitoring system with maintaining card / chip for 5 years including net charges for RMS System, complete upto net meter Installation and export to the grid with 5 year ON-SITE warranty and fully comprehensive maintenance contract as per Specification no. ESD-RT-ONG.aluminium conductor armoured cable of appropriate size is considered, Cost of mounting structure, PV cleaning unit, additional wiring,MSEDCL related fees, additional load charges, meter and testing charges is included in item.

Supplying and installation of solar PV module cleaning unit consisting of nozzles spray, necessary pipes, valves, post, electronic panel board concealed with weather proof cabinet, spreading water periodically for removal of dust, related motor pump, controller, timer and nozzles set suitable for covering 5 kWp Solar PV Module. (Approx. 35 Sq. Mtr. PV Module area) For item no. 4-8-8 for additional kW capacity, add Rs. 4500/- for every 5kWp.

Supply & Erecting IP 67 Neon Flexible 14 W/ Mtr RGBW Led Strip. It shall operate on DC 24V having Dimension of 22mm X23mm made up of polyurethene.

SlTC of high quality multicolor spot light, Power : 20W, Colour: RGB , Protection Rating : lP65, Beam Angle : 20°/45°, Body : Die casted, additional wall mount arrangements for fixing the lights. Optics: Specially designed to minimize hot spots & fringing in color mixing applications. Power lnput : DC 24V (without DC Driver) Make: Leksa Lighting/iGuzzini/Aultra Lighting/LaMartinie

SlTC of high quality long throw multi color linear wash light, Protection Rating : lP65, complying to BlS standard lS 10322 (Part 5/Sec 1): 2012, and having CE certification against standard EN 61547: 2009, EN 60598-1:2015, and EN 61347-2-13:2014.Mounting Structure : Additional wall mount yoke arrangements for fixing the lights. Rotation view : lnbuilt body rotating angle in degrees punched in the yoke/rear sides for uniform rotation angle to get the desired effect. Power consumption : 50W, CCT : RGB , (as per the design approval) Beam Angle 25°X25°, Control : DMX 512, Channel : 4 CH, Body : Die casted / extruded aluminium, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications.

Supplying & erecting Decorative light pole of height 4 m high (clear height) with decorative double bracket made out MS Pipe as per IS1161:1998 .The Pole will have provision for in built junction box weather proof flush door & locking arrangement for housing at bottom of the dia. of the pole shall be 140 mm & top section dia of 76 mm and base plate dimensions 250x250x10 mm thick and bottom and middle pipe of the pole shall be provided with cast iron /Aluminium embellishment to add aesthetic on the pole with the help of grub screw .The body of the decorative pole and bracket will be duly painted in U.V ray resistant PU coating in approved colour shade. The coating should have a DFT of 50 microns .The final design shall be got approved from Engineer in charge.

Supplying & erecting Decorative light pole of height 4 m high (clear height) with decorative Single bracket made out MS Pipe as per IS1161:1998 .The Pole will have provision for in built junction box weather proof flush door & locking arrangement for housing at bottom of the dia. of the pole shall be 140 mm & top section dia of 76 mm and base plate dimensions 250x250x10 mm thick and bottom and middle pipe of the pole shall be provided with cast iron /Aluminium embellishment to add aesthetic on the pole with the help of grub screw .The body of the decorative pole and bracket will be duly painted in U.V ray resistant PU coating in approved colour shade. The coating should have a DFT of 50 microns .The final design shall be got approved from Engineer in charge.

Supplying & erecting Decorative light pole of height 3 m high (clear height) with Single Arm decorative bracket made out GI Pipe as per IS1161:1998 .The Pole will have provision for in built junction box weather proof flush door & locking arrangement for housing at bottom of the dia. of the pole shall be 140 mm & top section dia of 76 mm and base plate dimensions 250x250x10 mm thick and bottom and middle pipe of the pole shall be provided with cast iron /Aluminium embellishment to add aesthetic on the pole with the help of grub screw .The body of the decorative pole and bracket will be duly painted in U.V ray resistant PU coating in approved colour shade. The coating should have a DFT of 50 microns .The final design shall be got approved from Engineer in charge.

Supplying & erecting Decorative light pole of height 3 m high (clear height) with double Arm decorative bracket made out GI Pipe as per IS1161:1998 .The Pole will have provision for in built junction box weather proof flush door & locking arrangement for housing at bottom of the dia. of the pole shall be 140 mm & top section dia of 76 mm and base plate dimensions 250x250x10 mm thick and bottom and middle pipe of the pole shall be provided with cast iron /Aluminium embellishment to add aesthetic on the pole with the help of grub screw .The body of the decorative pole and bracket will be duly painted in U.V ray resistant PU coating in approved colour shade. The coating should have a DFT of 50 microns .The final design shall be got approved from Engineer in charge.

Supply of 3mts decorative POLYSTEEL LAMP POST shall be made using FRP for outer cover as per requirement (Fiber reinforced marine grade polymer) inner section fabricated with 60 mm OD GI pipe as per ISI1239\1161 . Overall height of the pole including light fixture will be 3.5 mtr. Base plate as per ISI 2062 E250 grade size 430 diameter x10mm thick. The pole will be supplied with a Four Arm bracket and post top arrangement in center. The length of the top arm shall be 530 mm. FRP material shall be marine grade composite consisting of GSM 450 E AND 300 GSM , DENSITY 450 GMS/m2 and 300gms /m2 The overall thickness of the FRP base will be 2mm to 3 mm. The pole shall have a weatherproof flush door and locking arrangement for housing at the bottom of the pole junction box. It will accommodate 6amps mcb on bakelite sheet and heavy duty 32 amps connector suitable upto 4cx16/25sqmm al cable. The Pole base plate shall be suitable for M16 x600 mm J bolt. The pole base is 370 mm dia and height of base is 775 mm. The decorative element size is 370 mm height and max. dia 200 mm. The Sleeve of pole is fluted and diameter is 100 mm. Arm pipe is 25 mm OD attached with decorative corbel. The polysteel decorative lamppost will be pre-treated and duly painted with UV stabilized Polyurethane Aliphatic paint of approved colour shade

Supply of 3 mts decorative POLYSTEEL LAMP POST shall be made using FRP for outer cover as per requirement (Fiber reinforced marine grade polymer) inner section fabricated with 60 mm OD GI pipe as per ISI1239\1161 . Overall height of the pole including light fixture will be 3.5 mtr. Base plate as per ISI 2062 E250 grade size 430 diameter x10mm thick. The pole will be supplied with a Double Arm bracket and post top arrangement in center. The length of the top arm shall be 530 mm. FRP material shall be marine grade composite consisting of GSM 450 E AND 300 GSM , DENSITY 450 GMS/m2 and 300gms /m2 The overall thickness of the FRP base will be 2mm to 3 mm. The pole shall have a weatherproof flush door and locking arrangement for housing at the bottom of the pole junction box. It will accommodate 6amps mcb on bakelite sheet and heavy duty 32 amps connector suitable upto 4cx16/25sqmm al cable. The Pole base plate shall be suitable for M16 x600 mm J bolt. The pole base is 370 mm dia and height of base is 775 mm. The decorative element size is 370 mm height and max. dia 200 mm. The Sleeve of pole is fluted and diameter is 100 mm. Arm pipe is 25 mm OD attached with decorative corbel. The polysteel decorative lamppost will be pre-treated and duly painted with UV stabilized Polyurethane Aliphatic paint of approved colour shade

Supply of 3mts decorative POLYSTEEL LAMP POST shall be made using FRP for outer cover as per requirement(Fiber reinforced marine grade polymer) inner section fabricated with 60 mm OD GI pipe as per ISI1239\1161. Overall height of the pole including light fixture will be 3.5 mtr. Base plate as per ISI 2062 E250 grade size 430 diameter x10mm thick. The pole will be supplied with a Tripple Arm bracket and post top arrangement in center. The length of the top arm shall be 530 mm. FRP material shall be marine grade composite consisting of GSM 450 E AND 300 GSM , DENSITY 450 GMS/m2 and 300gms /m2 The overall thickness of the FRP base will be 2mm to 3 mm. The pole shall have a weatherproof flush door and locking arrangement for housing at the bottom of the pole junction box. It will accommodate 6amps mcb on bakelite sheet and heavy duty 32 amps connector suitable upto 4cx16/25sqmm al cable. The Pole base plate shall be suitable for M16 x600 mm J bolt. The pole base is 370 mm dia and height of base is 775 mm. The decorative element size is 370 mm height and max. dia 200 mm. The Sleeve of pole is fluted and diameter is 100 mm. Arm pipe is 25 mm OD attached with decorative corbel. The polysteel decorative lamppost will be pre-treated and duly painted with UV stabilized Polyurethane Aliphatic paint of approved colour shade

Supply of 6 mts decorative POLYSTEEL LAMP POST shall be made using FRP (Fiber reinforced marine grade polymer) inner section fabricated with 76 mm OD GI pipe as per ISI1239\1161 . Overall height of the pole including light fixture will be 6.5mtr. Base plate as per ISI 2062 E250 grade size 450 diameter x10mm thick. The pole will be supplied with a Double Arm bracket. The length of the top arm shall be 530 mm. FRP material shall be marine grade composite consisting of GSM 450 E AND 300 GSM , DENSITY 450 GMS/m2 and 300gms /m2 The overall thickness of the FRP base will be 2mm to 3 mm. The pole shall have a weatherproof flush door and locking arrangement for housing at the bottom of the pole junction box. It will accommodate 6amps mcb on bakelite sheet and heavy duty 32 amps connector suitable upto 4cx16/25sqmm al cable. The Pole base plate shall be suitable for M16 x600 mm J bolt. The pole base is 370 mm dia and height of base is 775 mm. The decorative element size is 370 mm height and max. dia 200 mm. The Sleeve of pole is fluted and diameter is 100 mm. Arm pipe is 25 mm OD attached with decorative corbel. The polysteel decorative lamppost will be pre-treated and duly painted with UV stabilized Polyurethane Aliphatic paint of approved colour shade

Supply installation testing and commissioning of Tier drop Luminaire of 40/50W. Decorative pendant / Hanging mounted compact street light. Type IV (Asymmetrical light distribution). Decorative luminaire made of specially contoured spun aluminium body of high corrosion resistance with a neck design for unique and better aesthetics and non corrosive stainless steel fasteners. Clear polycarbonate diffuser. The luminaire have extruded aluminium heatsink for thermal management with vertical fin design for longerlife of the LEDs. The mounting arrangement nipple, coupling & Hex nut made of Stainless steel 304 suitablefor mounting to internally threaded pipe of designation M30. Protection class IP65. Mechanical resistance IK09 (Polycarbonate diffuser). Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 3000K / 4000K / 5700K as per TMC Engineer and as per application. Colour rendering index (CRI)>70. Standard Deviation colour matching 3 MacAdam. Led module with expected service life of at least 72,000 operating hours. Driver shall be of approved make and are a Fixed constant current driver with an output current of 1200 MA, 48Vdc ,58W. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency > 85%, power factor > 0.95, THD < 10%, internal Surge Protection 6KV of the driver. Input Rated Voltage is 240V,50-60 Hz. Input operating voltage range of 100-300 Vac. The driver shall have short circuit protection with automatic restart, Overvoltage Protection, thermal protection and No load protection. Led Source shall be of Nichia / Lumiled/ cree or Equivalent Make and shall be of standard deviation colour matching to 3 Step Mcadam. External SPD of 10KV shall be provided along with the fixture. Luminaire dimension : 425mm diameter x height 407 mm / 437mm. BIS Certified for Luminaire.

Supply Installation testing and commissioning of 50W Post Top Luminaire Technical Description :Post top luminaire with Symmetrical light distribution. Luminaire made of gravity die cast aluminium top cover with decorative knob on top, gravity die cast aluminium housing integrated with decorative base leg and base. Die-cast aluminium base suitable for mounting Ø60mm OD pole. Translucent UV stabilised acrylic diffuser formed from non-yellowing acrylic sheet. All external screws are made of stainless steel. Protection class IP65. Pure polyester powder coated graphite grey / anthracite grey / jet black. Available colour temperature 2700K / 3000K / 4000K / 5700K, Colour rendering index (CRI)>80. LED module with expected service life of at least 60,000 operating hours. Prewired with LED driver and suitable for operating on 240V, 50Hz single phase ac supply. Driver efficiency >85%, Power factor >0.95, THD <10%, Surge protection 6KV. Input Rated Voltage is 240V,50-60 Hz. Input operating voltage range of 100-300 Vac. The driver shall have short circuit protection with automatic restart, Overvoltage Protection, thermal protection and No load protection. Led Source shall be of Nichia / lumiled/Cree Equivalent Make and shall be of standard deviation colour matching to 3 Step Mcadam. External SPD of 10KV shall be provided along with the fixture. Luminaire dimension : 480mm length x 417mm width x 850mm height. BIS Certified for Luminaire.

SlTC of Power Driver for above lights, POWER : 200W, lNPUT : AC 110-240V AC, 50HZ, OUTPUT : DC 24V, Protection rating lP66,Constant Voltage (C.V.) + Constant Current (C.C.) output, High efficiency up to 93%, orking temperature (case temperature)-45-+45°C, Protections: Short circuit / Over current / Over voltage / Over temperature, Comply with harmonic current limit per EN61000-3-2 Class C ( 50% load), Meet 4kV surge immunity level.

SlTC of Power Driver for above lights, POWER : 400W, lNPUT : AC 110-240V AC, 50HZ, OUTPUT : DC 24V, Protection rating lP66,Constant Voltage (C.V.) + Constant Current (C.C.) output, High efficiency up to 93%, orking temperature (case temperature)-45-+45°C, Protections: Short circuit / Over current / Over voltage / Over temperature, Comply with harmonic current limit per EN61000-3-2 Class C ( 50% load), Meet 4kV surge immunity level. It shall be provided with outdoor PVC/ FRP enclosure box to protect from sunlight, dust and water.

SlTC of 5 core DMX cable comprises twisted pairs with shield support for carrying of data. Featuring five/three pin connector support, these DMX- Cable options are suitable to be used with different type of fixtures. DMX512 cable is used for connecting all light consoles that use DMX 512 standard data transmission. Comprises pairs with a cross-section of 0.34 mm2 and general double screening.The external ultra-flexible sheath provides mobility of use and is very easy to coil.Make: FALCON/BELDEN/LL/GURUASTRONlCS

Supply testing commissioning of DMX controller,2 ports output which can control 2048 plus DMX pixels. It shall support Off-line control & play back content stored in the SD card up to 64GB and also l support at least 50 different scenes. It should be with digital touch screen display for changing modes, it supports master slave configuration to accommodate more DMX addresses (8x512 pixels Slave device) with outdoor enclosure to protect from sunlight, dust and water.

Supplying , erecting, testing and commissioning of 14W/mtr 24V RGBW DMX512 Addressable Led Strip with IP65 protection, RGBW Digital led strip has 120 LEDs/m with 10 Pixels/m, Copper core galvanised terminals, double sided electroplating board, havcing facility to crop at every 120mm

Supplying and erecting of 4 core 1.5 sqmm unarmoured PVC round sheathed bright annealed bare copper conductor heavy duty industrial flexible cable having voltage grade 1.1kV conforming to IS:694:2010

Supplying and erecting decorative LED Strip light 8 watt/mtr. Capacity with IP 65 class including necessary supply component. The LED strip shall be protected with transparent PVC material.

SITC ,of exterior BIS registered RGBW Linear LED Wall Washer luminaire for facade lighting with extruded aluminium housing, powder-coated finish, Clear toughened glass of 4mm thickness and die casted end caps, of Total System wattage not exceeding 80W with system lumen output >4000lm with all LEDs on, minimum system lumen efficacy >50 lm/w. Luminaire shall be capable of producing dynamic color changing light with 16 million colors as the light fixture should be programmable using 8 bit control DMX512 protocol / Ethernet based control. Luminaire should be complete with dedicated Lens made up of UL/VDE approved PC for each LED, offering beam angle of different types such as narrow, medium, wide or elliptical as per the site requirement. Fixture should have Height 125 mm ± 5% including surface mount base width 64 mm ± 5% , length 1200 mm ± 5% with constant locking

S & EM15 Female Supply Cable 1M 3 Pin

S & E M15 extension cable 1M 3 pin

SITC of exterior BIS registered RGBW Flexible LED Strip with 14.4 Watt per meter. LED Strip should have 60Nos LEDs per meter through out the length with the silicon cover with system lumens >708 lms/meter and System Lumen Efficacy >49lm/w. Standard Length of LED Strip is 5 mtr and it shall be capable of producing dynamic color changing light for with 16 million colors and should be programmable using 8 bit control DMX512 protocol / Ethernet based control. The Strip should have IP 67 protection with inbuilt IP67 connectors at both ends. DMX enabler circuit should be outside the Luminaire/LED Strip only. LED Strip shall be suitable to operate at an ambient temperature range of -20°C to 50°C. Life time shall be at least L70B50 @ 35000 burning hours at 50°C. LED should of make Nichea, Osram, Cree, Lumiled, Hongya of 5050 SMD package only. The rated voltage of the Luminaire should be 24VDC, Luminaire shall be offered with a BIS Approved Potted Driver of IP 66/67 rating made of extruded aluminium to make it more thermal efficient, Led Driver should have Operating input voltage range: 90-305Vac, PF > 0.95 and must have safety operation range form 90V - 176Vac. Life time of LED driver should be > 80,000 hours and MTBF of LED driver should be ≥ 2,00,000 hrs, Led driver must have SELV output and Case temperature i.e. Tc > 90°C. The product should be BIS approved with R number mentioned on product label. To be supported with Product test reports - LM79, BIS Report and LEDs Test Reports. Havells FLEXILINE COLOURSCAPE or Equivalent. Luminaire shall be conforming to BIS i.e. IS 10322 (PART 5/SEC 7) and shall be complete with all necessary accessories (Specially the aluminium Channels & diffuser for mounting) required for proper working of fixture including weather proof connection cables, water proof connectors etc. as required.

S & E LED driver CV250W24V10.5AEBV250S024SV

S & E DMX DECODER_RGBW_12V/24V_480W

S & E Instruction Forwarder Ranger/Compass(AC) / Strip

S & E 1 Mtr wire 5pin IP67 Female Connector RGBW

S & E 1M EXTENSION WIRE 5PIN IP67 RGBW

S & E Aluminium Channel with Diffuser (Running Meter)

Supplying and erecting of robust shock protection device for LED Lights upto 150 Watt. The device should be designed to enhance safety measures and mitigate the risk of electrical shocks. The device shall have insulation resistance between output and input should be 1000M Ohm or more at 500VDC and should withstand 1500VAC for 1 min.It should be suitable for outdoor application and hence should be totally enclosed and potted and IP66 protected. The device shall be tested in NABL accredited test laboratories for the given conditions Dimensions shall be not more than 160 X 100 X 80 mm. Flying leads of suitable ratings length not less than 0.25 meter for input and output connections shall be provided The device must comply with relevant indian electrical safety standards and regulations.It should effectively shield the lights from potential electrical hazards ensuring the protection of users and surrounding environment.It should ensure optimal performance and durability.

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core1.5 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

SlTC of Luxury Designer Fan Decorative Ceiling Fan Victoria – 60″ Classical fan with 5 x Dual Coloured Reversible blades with Summer-Winter Feature and optional Remote Integration Light Kit With LED Light, Features Reversible Blade, Summer Winter Feature, Fan Housing Colour Red Brass, Blades Material Special Wood, Blade Mechanism Regular Straight out Blade Size >52 Inches Blade Finish Wood Space Bed Room, Dining Room, Kitchen, Living Room, Patios, Category: Classical Vintage Collection etc Complete

SlTC of CHANDELIERS ARANYAKA by TISVA MAESTOSO CP16401E WATT - 16 x 40W GLS / 16 x 5W LED LAMP BASE - E14 CASE LOT - 1 NO. OF BOXES - 1

SlTC of LED Deep Recessed Downlighter with a nominal system lumen output of 1000 lumens and maximum system wattage of 9 Watts with a minimum system efficacy of 120 lm/W. The luminaire should have a color temperature of 3000 to 4500 K ,CRI>80 and SDCM<=3. The luminaire should have deep recessed COB light source with UGR<19. The luminaire shall meet IP20 rating with THD<10% and PF > 0.9. The luminaire housing should made of die-cast aluminum with a Polycarbonate aluminum coated reflector with 125 mm ceiling cutout, Class B Serviceability. The luminaire should have high gloss mirror optics with wide beam angle of 60-65 deg. The luminaire should have the provision for DALI dimmability. he fixture should comply with the parameters as per IS10322. The LED driver should comply to IEC61000-3-2 ed.3.2, 2009 for Harmonics, IEC61347 -2 -13, 2006 in Conjunction with IEC61347-1 ed.2.0, 2007 for Electrical Safety, IEC62384 ed.1.1, 2011 for performance and IEC61547 ed.2.0, 2009, CISPR-15 for EMI. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters.

SlTC of LED Deep Recessed Downlighter with a nominal system lumen output of 1000 lumens and maximum system wattage of 12 to 15 Watts with a minimum system efficacy of 120 lm/W. The luminaire should have a color temperature of 3000 to 4500 K ,CRI>80 and SDCM<=3. The luminaire should have deep recessed COB light source with UGR<19. The luminaire shall meet IP20 rating with THD<10% and PF > 0.9. The luminaire housing should made of die-cast aluminum with a Polycarbonate aluminum coated reflector with 125 mm ceiling cutout, Class B Serviceability. The luminaire should have high gloss mirror optics with wide beam angle of 60-65 deg. The luminaire should have the provision for DALI dimmability. he fixture should comply with the parameters as per IS10322. The LED driver should comply to IEC61000-3-2 ed.3.2, 2009 for Harmonics, IEC61347 -2 -13, 2006 in Conjunction with IEC61347-1 ed.2.0, 2007 for Electrical Safety, IEC62384 ed.1.1, 2011 for performance and IEC61547 ed.2.0, 2009, CISPR-15 for EMI. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters.

SlTC of LED Recessed Adjustable Spotlight with a nominal system lumen output of 1000 lumens and a minimum system efficacy of 90 lm/W. The luminaire shall have a rated system lifetime of 35,000 burning hours at L70. The luminaire should have a color temperature of 3000K and CRI>=80. The luminaire shall meet IP20 rating with PF > 0.9. The luminaire housing should made of pressure die cast aluminium and the luminaire optics shall have a high efficiency diffuser with more than 85% transmittance. The total power consumption should not exceed 12W (including driver).The luminaire should have Dimensions (L X W X H)mm of 105 mm (W) x 52 mm (H) and cutout dia 95 mm.

SlTC of LED Deep Recessed Weatherprof Downlighter with Modular Design, Multiple Trim options like Round,Square,U-Type with a nominal system lumen output of 1000 lumens . The luminaire shall have a rated system lifetime of 50,000 burning hours at L70. The luminaire should have a color temperature 3000K and CRI>=90. The luminaire shall meet IP20 rating with THD<10%, PF > 0.9, SDCM <= 3 and UGR<=19. The luminaire should be deep recessed type and housing should made of Albumin ADC12 .The fixture should have 75-90 mm ceiling cutout with 32-36 degree beam angle. The fixture should be CCC/CB/EMC/ASNZS certified. The total power consumption should not exceed 11W (including driver). For Toilets Master BEDRROMS

SlTC of SONY Bravia A80L 163.9 cm (65 inch) OLED Ultra HD (4K) Smart Google TV (XR-65A80L) Supported Apps: Netflix|Prime Video|Disney+Hotstar|Youtube Operating System: Google TV Resolution: Ultra HD (4K) 3840 x 2160 Pixels Sound Output: 50 W Refresh Rate: 120 Hz Display Size 163.9 cm (65 inch) Screen Type OLED HD Technology & Resolution Ultra HD (4K), 3840 x 2160 Series Bravia A80L Smart Tv Yes HDMI 4 USB 2 Built In Wi-Fi Yes Wall Mount Included Yes ideo Features View Angle 178 degree LED Display Type OLED Aspect Ratio 16:09 Refresh Rate 120 Hz Smart Tv Features Supported App - Netflix Yes Supported App - Youtube Yes Supported App - Disney+Hotstar Yes Supported App - Prime Video Yes Operating System Google TV Supported Devices for Casting Laptop, Mobile, PC Bluetooth Yes Built In Wi-Fi Yes Ethernet (RJ45) 1

SlTC of SONY Bravia X82L 138.8 cm (55 inch) Ultra HD (4K) LED Smart Google TV (KD-55X82L) Highlights Supported Apps: Netflix|Prime Video|Disney+Hotstar|Youtube Operating System: Google TV Resolution: Ultra HD (4K) 3840 x 2160 Pixels Sound Output: 20 W Refresh Rate: 50 Hz Video Features View Angle 178 degree Panel Type LED LED Display Type LED Refresh Rate 50 Hz Audio Features Number of Speakers 2 Speaker Type Bass Reflex Speaker Speaker Output RMS 20 W Smart Tv Features Processor 4K HDR Processor X1 Supported App - Netflix Yes Supported App - Youtube Yes Supported App - Disney+Hotstar Yes Supported App - Prime Video Yes Operating System Google TVScreen Mirroring Yes Supported Devices for Casting Laptop, Mobile, PC Bluetooth Yes Built In Wi-Fi Yes Ethernet (RJ45) 1 Connectivity Features HDMI 4 (Rear) USB 2 (Side)

SAMSUNG 32 L Slim Fry, Curd Making, A Perfect Gift With 10 Yr Warranty Convection & Grill Microwave Oven (MC32A7035CT, Silver) In The Box 1 Unit Microwave, 1 Unit Wire Rack, 1 Unit Crusty Plate, Quick Guide Label, User Manual Brand SAMSUNG Model Name MC32A7035CT Type Convection & Grill Capacity 32 L Color Silver Shade Silver Control Type Tact (Buttons), Jog Dial Dimensions Width 52.3 cm Height 30.9 cm Depth 50.6 cm Weight 20 kg

Supplying, installing, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the 2 loop capacity and capable of supporting upto 250 devices and detectors per loop, with on-board LCD display with min 16 lines of text, operating at 230 V 50 HZ - AC with inbuilt Battery Backup of a minimum 24 hours in normal condition and 30 min in alarm condition, suitable provision for network connectivity, interfacing with third party equipment via a MODBUS/ OPC/ L-ON interface etc. conforming to IS 15908:2021, IS 2189: 2008, EN 54 & VDS / FM/ UL 864 (10th edition) with 3 years replacement warranty FF-AFAS/CP.

Supplying, installing, testing and commissioning of repeater panel with suitable battery backup of a minimum of 24 hours in normal condition and 30 min in alarm condition, minimum 10" LCD or LED display with resistive touch screen or function keys and automatic back-light dimming and the status of any Fire/Fault of Integrated Fire Alarm Panels or minimum 80 characters backlit alphanumeric LCD display with inbuilt buzzer to indicate fault/fire alarm, manual control keys for silence/mute and to reset the FACP from the repeater station. Panel shall conforming to IS 15908:2021, IS 2189: 2008, NFPA-72, EN 54 / VdS/FM & UL with 3 years replacement warranty FF-AFAS/RP. (Compatible with 1/2 Loop Fire Alarm Control Panel), as per specification no FF-AFAS/RP

Supplying, installing, testing and commissioning of addressable optical smoke detector, single/twin LED’s with 360 degree view, suitable for low voltage 15 to 32 V DC two wires supply, in-built locking mechanism to check the removal and pilferage of the detector, in built isolation mode, start up current 300µA and alarm condition current shall be maximum 6.5 mA, operating temperature 0°C to 50°C, humidity 0-95% RH, IP 41, conforming to IS 2189: 2008, 11360_1985_Reff2020 EN 54 or UL Approved with 3 years equipment replacement warranty FF-AFAS/SD .

Supplying, installing, testing and commissioning of intelligent addressable thermal/heat detector with rate of rise cum fixed temperature thermistor complete with base as required, suitable for temperature variations from -20°C to 38°C for fixed-heat and rate-of-rise type detectors and 0°C to 66°C for high heat type detectors, in built isolation mode, suitable for offices/ceiling cable trenches/less ventilation area's etc. with 3 years equipment replacement warranty IS : 2175 - 1988 reaffirmed 2000, IS 15908:2021 standards FF-AFAS/SD.

Supplying, installing, testing and commissioning of Addressable Multisensor/Multicriteria Photo Thermal (Smoke + Heat) Detector. The detector shall have twin bi-colour LED for 360 deg viewing. The intelligent multi criteria detection device shall include the ability to combine the signal of the thermal sensor with the signal of the photoelectric signal in an effort to react hastily in the event of a fire situation. It shall also include the inherent ability to distinguish between a fire condition and a false alarm condition by examining the characteristics of the thermal and smoke sensing chambers and comparing them to a database of actual fire and deceptive phenomena. This item is referred for Non-conditioning Area conforming to EN 54/VdS / UL & FM approved with 3 years equipment replacement warranty, Designed to meet UL268, 7th Edition.

Supplying, installing, testing and commissioning of addressable fire control/relay module for AHU, Access Control, Lifts, Staircase Pressurization, Fire Suppression & other Third Party Outputs etc., Module shall conforming to IS 5051 Part 2 (Sec 1 to 3) : 1982 reed relays / EN 54/VdS / UL & FM approved with 3 years equipment replacement warranty, as per specification no FFAFAS/ CRM-FCM

Supplying, installing, testing and commissioning of addressable fire monitor module for flow switches, Panic Bars & other Third Party Inputs. The monitor module shall monitor potential free contacts. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the health status of the device complete as required. Module shall conforming to IS 5051 Part 2 (Sec 1 to 3) : 1982 Reed relays, EN 54/VdS / UL & FM approved with 3 years equipment replacement warranty, as per specification no FF-AFAS/MM

Supplying, installing, testing and commissioning of addressable fire isolator module for isolating short / dewired / loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that case needs to be considered with each detector & module. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the health status of the device. module complete as required. Module shall conforming to IS 5051 Part 2 (Sec 1 to 3) : 1982, , EN 54/VdS / UL & FM approved with 3 years equipment replacement warranty, FF-AFAS/ISM

Supplying, installing, testing and commissioning of addressable manual call points ( break glass type/pull station type), made of addressable break glass plastic square in shape surface/flush mounted with "Break Glass" massage embedded on the glass, complete erected with mounting base and required accessories, Module shall conform to EN 54/VdS / UL & FM approved with 3 years equipment replacement warranty, as per specification no FF-AFAS/MCP.

Supplying, installing, testing and commissioning of Addressable Sounder cum Strobe rated at minimum 75 dB @ 3m for Audible annunciation and minimum 75cd flashing at 1 Hz for visual indication. Module shall conforming to IS 2189: 2008, IS 15908:2021 / EN 54/VdS / UL & FM approved with 3 years equipment replacement warranty, as per specification no FF-AFAS/ S-ST

Supplying, installing, testing and commissioning remote response indicators suitable to operate on 5 - 28 V dc supply having FR Polymer ABS Housing complete as per specification no. FF-FAAS/RRI

Supplying, installing, testing and commissioning of digital linear heat detection cable along installation accessories e.g. clips, nails & end cap etc. duly addressable through monitor module with temperature ratings such as, 58°- 105°C, conforming to IS 2189: 2008, EN 54 or UL listed, as per specification no. FF-AFAS/LHDC.

Supply, installation, testing & commissioning of 4MP IP Dome/Bullet Camera with 1/2.8", progressive scan, CMOS, 2.8/4/6mm lens@ F1.8/2.0, angle of view more than 82° WDR 120db or above, Illumination Colour: 0.02 Lux (F1.8), 0.0Lux with IR ,Day/Night with auto switch ICR, ,supported H.264/H.265 MJPEG video compression ,Smart function supported (motion , IP66,CE, ROHS) IP66

Supplying, installing, testing & commissioning of 32/40 Ch Network Video Recorder (NVR), suitable connect Min. 32 IP Cameras, up to 5 Megapixel Resolution, with HDMI1/VGA1 outputs, provided Atleast one HDMI output of 4K resolution, atleast one VGA output with output up to 1920x1080, Support H.265 or higher, H.264, MJPEG, Supports Redundant Dual Power, Incoming Bandwidth 320 Mbps with minimum 8 SATA ports, ANR Technology, 8 SATA interfaces for 8 HDDs and capacity of each HDD up to 8TB, minimum 02 USB port, Alarm I/O 16/4, RJ-45 10/100/ 1000 Mbps selfadaptive Ethernet interface, support multibrand network Cameras, ONVIF conformance, Multiple network monitoring: Web viewer . support protocol TCP/IP, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS. RoHS, UL, CE, FCC certified. duly erected in provided U Rack with wiring connections, tagging and programming etc. complete as per specifications no. CCTV-NVR

Supplying, erecting, testing & commissioning of 1 kVA capacity on line pure sine wave,PWM,IGBT based UPS with 0.8 to unity output pf , single phase input & 1 phase output complete with all protections as per specification no. APUPS (Without batteries)

Supplying & erecting 6000 GB HDD

Supplying & erecting 43" professional LED display with 1920*1080 (Full HD) Display, suitable for 16/32 channel NVR and following features Brightness: minimum 500 Cd/m2 Contrast Ratio: minimum 1000:1 Viewing angle: 178/178 deg. Response time: maximum 8 ms Inputs: HDMI, VGA, BNC,USB, Audio In, Built-in speakers maximum 10 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. CCTV-MON

Supplying, fixing, and configuring 8-ports 1 GE un-managed gigabit PoE switch compliant with IEEE 802.3 standards, min. 120W PoE capacity with 2GE SFP uplink erected in provided rack complete.

Supplying, installing and testing UTP connector (RJ-45) as per specification no.WG-NAS/UTPC.

Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 500x550x480 mm) as per specification no. WG-NAS/RAK

Supplying and installing FR PVC sheathed HDPE insulated copper cat-6 cable suitable for networking compliant with ANSI/TIA-568.2-D standards in provided conduit/casing-n-capping as per specification no. WG-ELVC/NC

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 20mm with accessories on wall/ceiling as per specification no. WG-MA/CON.

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25mm with accessories on wall/ceiling as per specification no. WG-MA/CON.

Supplying and erecting HMS PVC conduit 25mm dia. with PVC accessories on wall/ceiling as per specification no. WG-MA/CON.

Supplying, erecting, testing and commissioning of 7HP to 8HP, VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47° C, non stop cooling even at 56° C and coefficient of performance (COP) 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000m operation in cooling mode with inverter/digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete.

Supplying, erecting, testing and commissioning of 16HP, VRF/VRV air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47° C, non stop cooling even at 56° C and coefficient of performance (COP) 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000 metre operation in cooling mode with inverter/digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suitable shape for increasing maximum heat transfer area, rain protection cover, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V±10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete.

Supplying, erecting & commissioning 4 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB

Supplying, erecting & commissioning 4 pole RCCB 16/25A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB.

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette room/indoor unit (IDU-compact / standard size) of nominal cooling capacity 3.0TR (1100 cfm) to 3.2TR (1165 cfm) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anti corrosive coating suitable for coastal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation.

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette room/indoor unit (IDU-compact / standard size) of nominal cooling capacity 3.3TR (1165 cfm) to 4.0TR (1218 cfm ) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for costal area in all respects suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation.

Supplying and installation of high pressure grade required size copper connection Y or T- Joints/refnut complete erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc. with brazing and testing for leakages confirming the normal operation of the VRV/VRF air conditioning system.

Supplying, erecting, testing and commissioning centralised programmable remote control panel (HMI) touch manager controls minimum 16 system of 64 ODU's can be controlled and up to 992 IDU's can be individually mounted and controlled indoor units having colour min 200mm size LCD touch panel, yearly schedule, power proportional distribution function, temperature limitation, history function complete erected on wall integrated with provided fire alarm system

Providing vaccumising the air conditioner system to 200 micron and charging with R-410A/R32 refrigerant for air conditioning unit.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 9.5 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge (hard drawn copper pipe for liquid main line and for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 12.7 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge (hard drawn copper pipe for liquid main line and for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 15.9 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge (hard drawn copper pipe for liquid main line and for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 22.2 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge (hard drawn copper pipe for liquid main line and for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 28.6 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge (hard drawn copper pipe for liquid main line and for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying and erecting 25 mm dia., 2.45 mm min. thickness polyethylene composite pipe, conforming to IS 15450 :2004 duly joined by compression/crimp fitted accessories, with internal as well as external end sealing arrangement for Solar Water Heater System as per specification No. ESD HWP/PCP.

Supplying and erecting 32 mm dia., 2.8 mm min. thickness polyethylene composite pipe, conforming to IS 15450 :2004 duly joined by compression/crimp fitted accessories, with internal as well as external end sealing arrangement for Solar Water Heater System as per specification No. ESD HWP/PCP.

Supplying and erecting 40 mm dia., 3.4 mm min. thickness polyethylene composite pipe, conforming to IS 15450 :2004 duly joined by compression/crimp fitted accessories, with internal as well as external end sealing arrangement for Solar Water Heater System as per specification No. ESD HWP/PCP

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 28 mm for solar water heater /AC system.

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 32 mm for solar water heater /AC system.

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 42 mm for solar water heater /AC system.

Supply, Installation, Testing & Commissioning of Corrosion Prevention Coating for fins (Coil Shield Plus) & Expose Copper Tube (AC Guard CP) per units.

Supplying, installing, testing and commissioning FR, XLPE armoured cable 4 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable 1100 V, 3 core 2.5 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Providing & erecting hot dipped galvanised perforated type cable tray manufactured from 16 SWG GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.7TR to 2.0TR capacity having ISEER minimum 3.8 to maximum 4.39 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/ SAC

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor. room air conditioning unit 1.7TR to 2.0TR capacity having ISEER minimum 5.0 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position in provided recess with wooden frame complete specification no. AP-AC/SAC

Supplying, installing, testing & commissioning cassette type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor room air conditioning unit 1.3TR to 1.7TR capacity having ISEER minimum 5.00 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32/R410A having copper condenser, dust filter, self diagnosis feature, stabilizer free operation, noise level maximum 50dBA at position as per specification no. AP-AC/ WAC

Supplying, installing, testing & commissioning cassette type room Air conditioning unit 2.8TR to 3.3TR capacity with refrigerant R32/R410A 415V, 50 Hz, A.C. supply having 1 no of air handling unit (Mega spilt) mounting type complete with temperature display on indoor unit, dust filter, noise level maximum 50dBA at position as per specification no. AP-AC/ WAC

Supplying, installing, testing & commissioning cassette type room Air conditioning unit 4TR to 4.4TR capacity with refrigerant R32/410A 415V, 50 Hz, A.C. supply having 1 no of air handling unit (Mega spilt) mounting type complete with temperature display on indoor unit, minimum dust filter, noise level maximum 50dBA at position as per specification no. AP-AC/ WAC

Supplying ,installing , testing and commissioning tower type room AC unit of 2.5TR to 2.9TR capacity suitable to operate on 415V, 50 Hz, A.C. supply having 1 no AHU and 1 no cabinet type floor mounting type condensing unit with refrigerant R32/410A & copper condenser coil with anticorrosive fins copper condenser , hydrophilic evaporator fins powder coated outer body ,with scroll/rotary compressor connected with provided refrigerant pipes, electric cables and drain pipe.

Supplying ,installing , testing and commissioning tower type room AC unit of 3.5TR to 3.9TR capacity suitable to operate on 415V, 50 Hz, A.C. supply having 1 no AHU and 1 no cabinet type floor mounting type condensing unit with refrigerant R32/410A & copper condenser coil with anticorrosive fins copper condenser, hydrophilic evaporator fins powder coated outer body, with croll/rotary compressor connected with provided refrigerant pipes, electric cables and drain pipe.

supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 6.4mm dia (OD) for liquid line/suction line supply and return piping of suitable gauge (hard copper pipe for liquid main line and soft copper pipe for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultraviolet radiations with OEM standards of VRV/VRF air conditioning system complete.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 19.1 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge (hard drawn copper pipe for liquid main line and for refrigerant) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, erecting & terminating FR XLPE insulated, galvanised steel wire armoured (round) cable 1100 V, 2 core 2.5 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

S & F of FM approved highly. flexible, closed-cell, 25 mm thick underdeck insulation of elastomeric foam based on synthetic rubber (NBR) tested for service temperature range -50-105'C as per EN 14706, EN 14707 & EN 14304, thermal conductivity A 3 0.037 WmK at mean temperature 0, = 20'C as per EN 12667 & EN ISO 8497, water vapour diflusion resistance factor y > 7000 as per EN '12086 & EN 13469, water absorption by volume 0.2o/o as per ASTM C 1763 & ASTM C 209, Class 0 fire performance as per BS 475 Part 6: 1989, Class 1 surface spread offlame as per BS 476 7: '1997, flammability HB, V.0 as per UL- 94, having good resistance to mechanical impact, excellent resistance to ozone, oil and chemicals, zero ozone depletion potential along with adhesives and other necessary accessories complete all as specified and directed by engineer-in-charge. .

Carrying out comprehensive annual maintenance for entire electrical work for first year after defect liability period (2.5% on Electrical estimate cost)

Carrying out comprehensive annual maintenance for entire electrical work for second year after defect liability period (4% on Electrical estimate cost)

Carrying out comprehensive annual maintenance for entire electrical work for Third year after defect liability period (5.5% on Electrical estimate cost)

Carrying out comprehensive annual maintenance for entire electrical work for fourth year after defect liability period (7% on Electrical estimate cost)

Supplying & erecting 2 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, Nylon Rip Cord & grey colour sheathed with FR PVC, conforming to ITD specification S/WS 113C laid in provided PVC casing capping/conduit as per specification No. WG-TW

Supplying & erecting 10 pair, 0.5mm dia, jelly filled unarmoured telephone copper cable with poly-al laminate moisture barrier, laid in provided PVC casing capping/conduit as per specification No. WG-TW

Supplying & erecting 20 pair, 0.5 mm dia. jelly filled armoured telephone copper cable with poly-al laminate moisture barrier, polythene sheathed, G.S.Tape armoured polythene jacketed having laid in provided trench as per specification No. WG-TW

Supplying & erecting 100 pair, 0.5 mm dia. jelly filled armoured telephone copper cable with poly-al laminate moisture barrier, polythene sheathed, G.S.Tape armoured polythene jacketed having laid in provided trench as per specification No. WG-TW

Supplying & erecting co-axial copper cable low voltage grade tri-shielded RG-11 as per specification No. WG-TW

Supplying & erecting co-axial copper cable low voltage grade tri-shielded RG-6 as per specification No. WG-TW

Supplying and erecting 5m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete.

Supplying, erecting & commissioning MDF Box 50x50 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW

Supplying, erecting & commissioning MDF Box 100x100 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW

Supplying, erecting & commissioning 10 pairs FR junction box with moulded plastic enclosure as per specification no. WG-TW

Supplying, erecting & commissioning 10 pair module for connection & disconnection of telephone cable as per specification no. WG-TW

Supplying and erecting broadband splitter unit with 1 input & 2 output RJ 11 female connectors complete.

Supplying, installing, testing & commissioning digital (hybrid) type EPABX of 6 x 32 universal extensions suitable upto 96 extensions compliant to IEC 61000, EN 60950, CISPR 22, IS:9000 part 2/section 4 having LAN/WAN port, USB port, RS232 port as per specification complete as per specification no. WGTA

Supplying, installing, testing & commissioning push button telephone instrument desk top/wall mount with caller ID & Speaker unit as per specification complete.

Supplying and installing LSZH sheathed HDPE insulated copper cat-6 cable suitable for networking compliant with ANSI/TIA-568.2-D standards in provided conduit/casing-n-capping as per specification no. WG-ELVC/NC

Supplying and installing FR PVC sheathed HDPE insulated copper cat-6 cable with rodent proof and anti termite jacket suitable for networking compliant with ANSI/TIA-568.2-D standards in provided conduit/casing-ncapping as per specification no. WG-ELVC/NC

Supplying and erecting 6 fibers LSZH armoured multimode optical fiber cable with, core dia 50/125 μm (OM3), suitable upto 10 GBPS, compliant to IEC 60793/IEC 60794 standards, on wall/ceiling or laid in provided pipe/trench as per specification no. WG-ELVC/OFC

Supplying and fixing 1 m 24 AWG multi stranded UTP patch cord with RJ-45 factory crimped connector of Cat 6 type, compliant ANSI/TIA-568.2-D standards in position as per specification no. WG-ELVC/PC

Supplying and fixing 3 m 24 AWG multi stranded UTP patch cord with RJ-45 factory crimped connector of cat 6 type compliant ANSI/TIA-568.2-D standards in position as per specification no.WG-ELVC/PC

Supplying and installing 3 m fiber patch cord LC-LC duplex single mode for OS1/OS2 compliant to IEC 60793/IEC 60794 standards complete as per specification no. WG-ELVC/FPC

Supplying, fixing, and configuring 24 ports, PoE switch compliant with IEEE 802.3 standards with min. 193W PoE capacity with 4GE SFP uplink in provided rack as per specification no. WG-NWC/ENS

Supplying, fixing, and configuring 20 (1G-RJ45) ports + 4 combo 1G ports + 4 10G (SFP+) ports, layer 3 switch, 6KV surge protection on ethernet port and console port for management & support OSPF, BGP, MPLS, policy based routing compliant with IEEE 802.3 standards erected in provided rack complete.

Supplying, installing and testing UTP connector (RJ-45) as per specification no. WG-NAS/UTPC.

Supplying and fixing tool-less IO (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.

Supplying and fixing Cat 6, keystone jack RJ-45 information outlet compliant with ANSI/TIA/EIA 568.C.2 & ISO/IEC 11810 (ethernet) as per specification no. WG-NAS/KJ

Supplying and fixing Cat 6, 24 port patch panel with keystone jacks compliant with ANSI/TIA/EIA 568.C.2 & ISO/IEC 11810 complete as per specification no. WG-NAS/PP

Supplying and fixing POE adaptor to provide DC supply to ethernet devices as per specification No. WG-NAS/PEA

Supplying and fixing Power Distribution Unit for networking rack comprises of 6/16A (6 Nos. sockets), 25 A modular MCB, appropriate rating fuse and indicator lamp, enclosed in black powder coated metal with necessary arrangement for fixing as per specification No. WG-NAS/RAK

Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 500x600x500 mm) as per specification No. WG-NAS/RAK

Supplying and fixing 15U wall mount rack (Dimension-DxWxH – 500x550x747 mm) as per specification no. WG-NAS/RAK

Supplying and fixing 6U Hybrid IP66 outdoor mount server rack with pole mount bracket (Dimension-DxWxH - 500x550x350 mm) as per specification no. WG-NAS/RAK

Supplying, fixing, and configuring dual-band manageable wireless, 4x4 802.11 AX Wifi 6 high performance, 3600mbps, with 2 ethernet ports 1 supporting GE & another port supporting 2.GE unified, concurrent access point with POE in networking as per specification no. WG-NAS/LAP2

Supplying, fixing and configuring hardware wireless controller supporting minimum 100 Indoor/Outdoor AP complete as per specification WGNAS/ APWC

S/I/T/C of Video Conference Solution with ALL-IN-ONE VIDEO BAR FOR LARGE CONFERENCE ROOMS ( USB/BLUETOOTH® SMART SPEAKERPHONE FOR FLEXIBLE/ HUDDLE ROOMS) with having 12x PTZ Camera, should support dual display for Video and content, 4K content sharing, wired and wireless content sharing, 3 or more microphones, should support 200 mobility users with 5 year license from day 1 the system should be complete with all respect and handing over with atlist 3 demo for end user the cost are all inclusive in above line item.

S/I/T/C of 86" Interactive Display, 3840 x 2160 4K Display, 178° Viewing Angle, 370 cd/m², 20 Touch Points, 1 billion colors, Tempered and Anti Glare Glass, Android 8.0 or higher, 2 x 15W speakers, OPS PC having core i7, 8GB RAM and 256GB SSD the system should be complete with all respect and handing over with atlist 3 demo for end user the cost are all inclusive in above line item.

S/I/T/C of Passive Wall Plate — HDMI: Front Panel Connection — 1 HDMI (F). Rear Panel Connection — 1 HDMI (F) on a flat, flexible cable.

S/I/T/C of Dual HDMI Module Passive Wall Plate — HDMI: Front Panel Connection — 1 HDMI (F). Rear Panel Connection — 1 HDMI (F) on a flat, flexible cable.

Providing, laying and jointing in position G.I. heavy duty C class pipes confirming to I.S. 1239 with welded joints for pipes and flanged joints for valves and accessories including all fittings including cutting the pipes to correct length, providing and welding M.S. flanges for connection to valves and accessories, providing epoxy coating to welded surface, testing to 1.5 times working pressure, including painting the pipes with bituminous paint and wrapping the pipes with IWL (Pypkote) wrapping of 4mm thk as per manufacturers instruction all complete including with haliday test upto satisfaction of Engineering Incharge, all excavations in any type of soil, refilling the trenches after testing disposing of surplus material, dewatering etc. complete all as per directions for the following diameters. 150 mm dia.

100 mm dia.

80 mm dia.

65mm dia.

50 mm dia.

40 mm dia.

32 mm dia.

25 mm dia.

Galvanised iron "C" class pipes(IS1239 Part - 1 including cutting, screwing, welding etc. complete with fittings viz. tees, elbows, bends, flanges, reducers etc including excavations (upto 1.5 m deep) p:c:c 1:2:4 thrust blocks, back - filling with excavated earth, removal of surplus soil and providing anti-corrosive treatment (coating and wrapping) as per IS: 10221 complete as required for all external hydrant system piping 200 mm dia.

150 mm dia.

100 mm dia.

80 mm dia.

15 mm dia. quartzoid bulb type G. M pendent sprinkler head set to operate at 68 Deg C (rate in rise) and as per IS 9972

Providing and fixing in position 100 x 80 mm size tee junction on the wet riser, flanged or welded for fixing to the Double outlet hydrant valve including hydraulic testing, painting etc. complete

Providing and fixing approved drum type wall mounted hose reels, swivelling 180 degrees consisting of 20mm dia x 30 m long best approved , armoured rubber hose pipe with 6.3 mm dia bronze shut off type jet nozzle, making connection to the vertical riser by cutting welding, including providing 20mm dia shut off valve, all necessary piping, fittings, fixing the hose reel with necessary anchor fastners by drilling holes in walls /RCC, making good the same all complete as per direction of the Engineer-in- charge

Providing and installing in position 2 lengths of 15m long and 63mm dia non-perclating RRL Fire Hose (as per IS 636) along with couplings, short size gun metal branch pipe with 16mm gun metal nozzle, housed in a metal box with lockable glass doors and painted post office red,

Supply and installation of M.S Cabinet with glass and locking arrangement , suitable for 2 lengths of RRL hose and 1 no of Branch pipe, 2 coats of primer paint as per seven tank process and powder coated finally in post office red etc. complete Size 1000mm x 750 mm

Providing and fixing courtyard fire hydrants as per IS 5290, consisting of 63mm dia, single outlet flanged oblique type hydrant valve with instantaneous female plunger type coupling, chained blank cap including making flanged joints by providing necessary nuts, bolts, gaskets (6 mm thick neoprene) all complete as suitable for 80mm dia stand post.

Providing and fixning fire Brigade inlet Siamese connection fabricated from 100 mm G.I. pipe with 4 nos 63mm dia G.M. male hydrant connection including providing and fixing 100 mm dia Butterfly valve, non return valve etc. for the wet riser, etc complete

Providing and fixing bronze orifice disc for fire hydrant system and courtyard hydrants to control the pressure within 5.5 kgs/cm2 including rubber gasket packing, bolts, nuts, washers, all complete as per direction of the Engineer - in – charge

Providing and fixing C.I. air release valve of 40 dia and G.I. drain pipe of 0.5mt length including necessary support and painting with two coats of enamel paint over a coat of primer etc. complete, for wet riser termination.

Providing and fixing .Ball valve of 40 mm dia. and GI drain pipe of 0.5 length including necessary support and painting of two coats of enamel paint of approved colour over a priming coat etc complete on the lower end of the

Providing and fixing in position cast iron butterfly valve standard pattern (Horizontal / Vertical) of pressure rating PN 16 including necessary flanged joints by providing necessary nuts, bolts, gaskets, etc. all complete of the of the following diameters 100 mm dia

Providing and fixing heavy approved quality cast iron dual plate type non return valves (PN-16) Flap to be of CI while Flap seat ring to be of GM. including making joints etc all complete for the following diameters . 100 mm dia

Providing horizontal monoblock centrifugal booster pump having cast iron casing bronze impeller, EN 8 shaft driven by 7.5 HP including Concrete Foundation for Booster Pump.

Providing and fixing pressure gauge, glycerine filled with isolation valve

providing and fixing of starter of Booster pump

Booster pump Cabling 2.5sq x 6 core armoured cable

SITC of Core Cutting 6"

Electric motor driven fire hydrant system pumping set suitable or automatic operation consisting of the following:

Electric motor driven automatic pressurisation (Jockey pumps) consisting of folloing:

Cubical type floor mounted main fire pump control panel fabricated from 16 G M.S. sheets duly painted with stove enameled finish off approved shade suitable for the fire / jockey pumps and complete with incoming and outgoing switchgear, bus bars, starters, indicating lamps, volt meter, ammeter and all inter connecting power and pressure switch control cabling extra from plate and as directed.

Electric motor driven fire hydrant system pumping set suitable or automatic operation consisting of the following: A) Horizontal, centrifugal, end suction fire pumps having cast iron body, bronze impeller, stainless steel shaft & capable of delivering 2400LPM against a total head of 76 M complete with necessary pressure guage & pressure switch on the delivery side including bypass arrangement as required for periodical testing of the working of the pumping sets also with nrv,ystrainer & valves complete in all B) Squirrel cage induction motor totally enclosed fan cooled type suitable for 400 / 440 volts (+5%) 3 phase, 50 HZ, A.C. supply of suitable capacity for the above mentioned pumps with synchronous speed of 3000 RPM confirming to IS:325 and duly coupled with above pumps with flexible coupling including earthing as per relevant Indian Standard

ISI marked (IS:13849) portable fire extinguishers, ABC dry powder type of capacity 5 Kg with pressure gauge, discharge hose and nozzle and complete in all respects including initial fill.

4 Nos fire buckets 9 lts capacity each made out of 24g GI sheet with round bottom, painted with white synthetic enamel from inside and fire red from utside and lettered 'FIRE' in black complete with bucket stand etc. complete including initial fill of sand.

Hirani Enterprises