REPAIR TO ROOF, GALVALUME SHEETS, AC SHEETS, FALSE CEILING, WALL PANELLING, PARTITIONS ETC AT CHHEOKI MIL STN UNDER GE (WEST) PRAYAGRAJ

Amount

Dismantling of brick tiles laid bedded and pointed in any morter or brick tiles on roof , floors, channels, kerbs, aprons etc,cement concrete of any description & in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of Mud/mud puska in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and directed.

M&L for Cutting out cracks to V-section in existing roofs or terracing, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight) complete all as specified and directed.

M&L for Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

M&L for PCC 1:3:6 type B-1(using 20mm graded stone aggregate) for providing cement concrete as levelling and roof kerbs or mud stops, including finishing the surface with grinder to receive the acrylic based water proofing material, rounded or chamfered on edges etc complete all as specified and directed.

M&L for rendering or bedding layer 15mm thick in cement mortar (1:3) cover concrete surfaces of roof, mixed with WPC 2% wt of cement inclduing finishing surfaces even and fair without using extra cement complete all as specified and directed.(Note: WPC will be measured and paid separately).

M&L for preparation of new surface and applying a coat of hot blown bitumen of grade 85/25 conforming to IS 702 over primed surface of roof slab @ 1.20 Kg/Sqm complete all as specified and directed.

M&L for APP based polymeric water proofing membrane minimum weight 3 Kg/ Sqm and minimum 3mm thick reinforced with polyster non wove fabrick (Weight not less than 150gms/Sqm or as per IS), laid over hot bitumen surface by torched application with the strict supervision of manufacturers technical supervisor. Membrane shall be laid with 100mm side/end lap on prepared surface as per manufacturer instruction work shall be carried out strictly with the technical tradesmen and supervision of technical staff of manufacturer.complete all as specified and directed.

M&L for rendering or bedding layer 15mm thick in cement mortar (1:3) cover concrete surfaces of roof, mixed with linesed oil @ 3% wt of cement inclduing finishing surfaces even and fair without using extra cement inclusive linesed oil complete all as specified and directed.

M&L for Cement concret tiles 25cm x 25cm x 22mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors/roof , and cut and polished complete all as specified and directed.

M&L for preparation of new APP based polymeric water proofing membrane surface and including applying Two coat of aluminium paint over membrane, coat each coat should have @ 0.1 liter per sqm complete all as specified and directed.

Supply only Integral waterproofing compound Make Dr Fixit/ Pidipfoor/ LW+.

M&L for PCC (1:2:4) type B-0 (using 12.5 mm graded stone aggregates) as in roof kerbs, Chajja of window/ventilator or mud stops, rounded or chamfered on top of chajja & side edges of surfaces upto the height of 7.00 mtr etc complete all as specified and directed. { The rate is deemed to be inclusive of scaffolding/form work }

S&F in repair rotational moulded polythene water storage tank of capacity 500 ltrs (Cylindrical/vertical with closed top), triple layer construction, ISI marked, hoisted & fixed in position including 20 ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and tank cover directed complete all as specified and as directed. note :- the rate of taking down and removing old PVC water will be inclueded.

S&F in repair rotational moulded polythene water storage tank of capacity 1000 ltrs (Cylindrical/vertical with closed top), triple layer construction, ISI marked, hoisted & fixed in position including 20 ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and tank cover directed complete all as specified and as directed.note :- the rate of taking down and removing old PVC water will be inclueded

S&F in repair 15 mm ball/ float valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed 20mm bore minimum weight 210 gms complete all as specified and as directed.

S&F in repair Stop valves/Gate valves 20 mm dia cast copper alloy,screwed down, high pressure with crutch or butterfly handel, screwed both ends for iron pipe or for unions and fixed.complete all as specified and directed.

Taking up or down steel/CPVC 15mm tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down steel/CPVC 20mm tubing and connections including cleaning for refixing or removal to store complete all as specified and directed.

Supplying and laying of CPVC 16mm outer diameter pipes SDR 11 and included plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

Supplying and laying of CPVC 20mm outer diameter pipes SDR 11 and included plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F for 16 mm outer dia CPVC Brass Elbow/Tee/Male/Female Adapter Tank Adapter Union etc with all fittings and fixed complete to walls, ceilings or laid in floors complete all as specified and directed.

S&F for 20 mm outer dia CPVC Brass Elbow/Tee/Male/Female Adapter Tank Adapter Union etc with all fittings and fixed complete to walls, ceilings or laid in floors complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories).

S&F for 110 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed

S&F for 75 mm diaPVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed

S&F for PVC SWR (110) bends any radius comlete all as specified and directed.

S&F for PVC SWR (75) bends any radius comlete all as specified and directed.

S&F for stack clamps out of 50mm by 5 mm flat iron and 16 mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roofs for bore of 100mm complet all as specified and directed.

S&F for stack clamps out of 50mm by 5 mm flat iron and 16 mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roofs for bore of 75 mm complet all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar incl all quoins, arches, pillars etc but excluding ashlars facings dressed stone work and forecast concrete articles, complete all as specified and directed.

M&L for brickwork with sub class 'B' bricks, straight or curved on plan exc 6m mean radius built in CM 1:6, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc, incl raking out joints, hacking for key, scrubbing down with water, etc & prepare to receive new plaster complete all as specified and directed

M&L for 15mm thick rendering in CM 1:6 on fair faces of brick work, surfaces finished even and fair without using extra cement complete all as specified and directed

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work, finished even and fair without using extra cement complete all as specified and directed

M&L for rendering 5mm thick in CM 1:3 finished even and smooth with out using extra cement in ceiling complete all as specified and directed

M&L for preparing new plaster surfaces of ceiling and applying two coats of white wash over coat of primer of Chalk whiting, on plastered surfaces, complete all as specified and directed.

M&L for preparing new plaster surfaces of wall and applying two coats of oil bond distemper over and including priming coat of interior primer applied @0.90 litre/10 sqm over minimum 2 mm thick wall care putty in two coat, Each coat should have 1 mm thick complete all as specified and directed.

M&L for preparing new plaster surfaces of Walls and applying two coats of white wash over coat of primer of Chalk whiting, on plastered surfaces, complete all as specified and directed.

M&L for complete removing existing treatment on wall surface and applying two coats of oil bond distemper over and including priming coat of interior primer applied @0.90 litre/10 sqm over minimum 2 mm thick wall care putty in two coat, Each coat should have 1 mm thick complete all as specified and directed.

M&L for complete removal of existing treatment on Walls and applying two coat of white wash over coat of primer of Chalk whiting, on plastered surfaces, complete all as specified and directed.

M&l for Preparation of new plastered surface of wall and applying two coats of cement base paint over a coat of primer of Chalk whiting, on plastered surfaces, complete all as specified and directed.

M&L for applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm / liter and UV resistance as per IS15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre /10sqm over and including priming coat of exterior primer applied @0.90 litre/10 sqm over new plaster surfaces of walls complete all as specified and directed.

M&L for complete removal of existing treatment on Walls surface of wall and applying two coats of cement base paint over a coat of primer of Chalk whiting, on plastered surfaces, complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50gm / liter and UV resistance as per IS15489:2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company depot tinted) with silicon additives @ 1.43 litre /10sqm over and including priming coat of exterior primer applied @0.90 litre/10 sqm over old surfaces of walls ( Note wall surface made smooth and application of distemper through Mechanical mean) complete all as specified and directed.

M&L for Preparation of old distemper surface by washing, rubbing down and stopping of distemper and painted surface and applying one coat oil bound emulsion on wall surfaces white or tinted complete all as specified and directed.

M&L for Preparation of old painted steel surfaces of any description, over 10 cm width or girth and applying one coat of synthetic enamel paint (ordinary tint), complete all as specified and directed.

M&L for preparation of old painted steel Surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of red Oxide, zink crome primer complete all as specified and directed.

M&L for preparation of old wooden Surfaces of any description, over 10cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint, complete all as specified and directed.

M&L for preparation of old wooden Surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Dismantling of asbestos cement ( plain ,corrugated, semi corrugated etc) sheets in roof coverings including ridges complete all as specified and directed.

M&L for 6mm thick asbestos cement, corrugated or semi-corrugated sheets in roofs, walls etc Fixed with L-type or J-type or cranked hook bolts complete all as specified and directed

S&F for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering or fixed to wall with self tapping screws complete all as specified and directed

S&F for Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering or fixed to wall with self tapping screws complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F for Steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to I S.1161-1979 grade St.-240 tubular trusses complete all as specified and directed.

S&F for Framed work of rolled mild steel conforming to Fe 410-W (GdeE- 250) quality A as in doors or gates of angle or other section with gusset plates, rails, braces, etc, drilled for fixing of steel sheeting or other covering; doors etc to be prepared for hanging or sliding with and including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting, running rails & guides) and hanging, fastening & fixing complete all as specified and directed.

S&F for Roof trusses(framed) of rolled mild sheel conforming Fe 410-W (GdeE- 250) quality A as a trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed.

S&F for Rolled sections of rolled mild steel as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. and similar work conforming to Fe 410-W (Gde E- 250) qualityA complete all as spesified and directed .

M&L for Preparing new or previously untreated steel & iron surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over & including a coat of red oxide primer complete all as specified and directed.

Excavation in post holes (or similar holes) each n. exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around. In layers n. exc 25cm, for hard/ dense soil complete all as specified and directed.

Demolition of cement concrete unreinfoced in ground floor and paving n exc 15 cm thickness ( below or above ground level) and removing the unserviceable materials to a distance n exc 100m complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) Cement concrete in foundations filling , floor and mass concrete for column post etc complete all as specified as directed.

M& L for 75mm thick PCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in flooring in size of panel 2X2 mtr minimum using with Glass dividing strips,complete all as specified as directed.

M&L for Plastic dividing strips,1.5mm thick inserted in position,conform to design and 38mm wide complete all as specified and directed.

M& L for PCC 75mm thick type C-1 ,1:3:6 using 20mm graded stone aggregate as in plinth protection and floor/sub base etc complete all specified as directed.

M&L for Chequered cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors over 15mm thick screed bed in cement mortar (1:6) including jointing with neat cement slurry mixing pigment to match the colour etc complete all as specified and directed.

S&F in repair roller blind decorated horizontal type with necessary pulling threads, including powder coated aluminium canopy box and bottom rail along with all arrangement fixed to door, window/ ventilation as per sample approval by GE completed all as specified & directed.

Dismantling of stone slabs and tiles of any description or thickness in floors aprons etc including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 18- 20mm thick granite Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white ement (1:2) using marble dust with admixture of pigment to match with shade of granite including moulding complete all as specified and directed.

S&F in repair 3mm thick Aiuminium composite panel for partition /cladding using aluminium composite panel sheet of 3mm thick( Platinum series of Envitect) over steel frame work,MS Tube (ACP will be fixed over MS tube welded over MS steel framed works) and filling the gaps with silicon,sealant and other material of approved quality as per sample approval by GE.complete all as specified and directed. Note :- mild steel frame work including nuts and bolts will be measured and paid seperately.

S&F in repair for metallic stainless steel (304 Grade) letter for emblem in logo or Devanagari/ English script, hieght of each letter should be minimum 300 mm with appropriate width i.e.(200mm -300 mm) and 25 mm thick with 40 mm depth of letter in 2 mm thick plate,fixed on vertical suraface at the side of entrance gate, complete all as specified and directed.

S&F in repair for 3D LED Acrylic lletter for emblem in logo or Devanagari/ English script, hieght of each letter should be minimum 300 mm with appropriate width i.e.(200mm -300 mm) and 25 mm thick with 40 mm depth of letter in 3 mm thick plate and fixed over ACP panel on vertical surface at the top of entrance gate, complete all as specified and directed.

Dismentling of floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified and directed.

M&L for 25mm thick Cement concrete type B-0, 1:2:4 (12.5mm graded crushed stone aggregate) in floors ,sub base, sub floor etc complete all as specified and directed.

M&L for double charged Virified Ceramic tiles 9-10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.32 Sqm but not exceeding 0.72 Sqm each in floors, skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile and laid over and inclduing 15mm thick screed bed layer in CM (1:6) complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation. etc) or insulation boards/slabs/blankets, any thickness, includinguding cover fillets complete all as specified and directed.

Providing & fixing ceiling with mineral fiber 12 mm thick micro tegular edged false ceiling tiles at all height ,False ceiling tiles of size 595x595 mm of approved texture design patterns having moisture content less than 2%, humidity resistance of 99%, as per IS 8225:1987, light reflectance of 85% (Minimum) to be laid in true horizontal level suspended on inter- locking metal T-Grid of PVC coated Anodised aluminium snap grid frame work for false ceiling comprising of main- T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600 mm to form grid module of size 600x 600mm, suspended from ceiling at approprite height from floor using galvanized mild steel wire and L- shape level adjuster of size 85x25x2mm Anodised aluminium perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in- Charge. Note : (i) Ceiling tiles shall be authorised brand of make as specified in Appendix 'B' to particular. (iv) Work shall be executed by manufacturer's authorised vendor.

S&F for corrogated PVC Wall Lining / cladding consisting of 7 -8 mm thick any colour or pattern inclusive of solvent cement and fixing at site on PVC frame with nails as per specifications and drawing completed all as specified & directed.

S&F for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing completed all as specified & directed.

S&F for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering or fixed to wall except sheet for refixing old with self tapping screws complete all as specified and directed

S&F for Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering or fixed to wall except sheet for refixing old with self tapping screws complete all as specified and directed

Disconnecting existing tanks, capacity exc 250 and n. exc 500 ltr setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed by Engg-in-Charge.

Disconnecting existing tanks, capacity exc 500 and n. exc 1000 ltr setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and directed by Engg-in-Charge.

Taking down chowkats with shutters not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking of shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, including necessary aluminium fittings like aluminium butt hinges(125 mm) 03 Nos, aluminium handle(200mm) 02 Nos, aluminium tower bolts (200 mm)01 No, aluminium door stopper 01 Nos, and key lock complete all as specified and directed. Note:- filling material in door pannel glass/ ACP sheet will be measured and paid seperately in respective items.

S&F for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket locking arrangements as per sample approval by GE. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F for 5 mm thick glass for alumnium partiton /Door/ window/ ventilator fixed with EPDM rubber/ neoprene gasket all complete as per architectural drawings and the directions of Engineer-in-Charge

S&F for Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as specified and directed.

S&F in repair for Door closer of aluminium ( die cast ) body hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1200 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed

S&F in repair for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed

S&F in repair for Anodised aluminium work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket locking arrangements as per sample approval by GE. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. Note : (i) the rate of taking down and removing old alumnium scrap of door,/window/ ventilation/ fixed partition to be included.. (ii) Builder's hardware i.e. hinges/tower bolt/ handle will be measured and paid seperately.

S&F in repair for 3.5 mm thick glass for alumnium partiton /Door/ window/ ventilator fixed with EPDM rubber/ neoprene gasket all complete as per architectural drawings and the directions of Engineer-in-Charge

S&F in repair 125 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed, type B-21 complete all as spesified and directed .

S&F in repair 200 mm long Aluminium anodised barrel tower bolts of extruded section.complete all as spesified and directed .

S&F in repair 150 mm long Aluminium anodised barrel tower bolts of extruded section.complete all as spesified and directed .

S&F in repair for 125 mm long Extruded Aluminium alloy handles, fabricated type, anodised.complete all as spesified and directed .

S&F in repair for 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised.complete all as spesified and directed .

Schedule of Credit (MINUS) Rs. 2,31,975.00 B/F from Serial Page No. [Note : Details of items for schedule of credit is given on Srl Page No. _____] This amount shall be automatically deducted to arrive at tendered sum

M/S AVANI TRADERS (BID ID -3469193)

M/s VIJAY TRADERS (BID ID -3468331)

K R GUPTA AND SONS (BID ID -3469793)