SPL REPAIR TO ROOF TREATMENT, FLOORING, PLUMBING, JOINERY AND ALLIED WORKS IN BLDG. NO 154 D COOK HOUSE (ALL COY) OF 9 KUMAON AND OTHER CERTAIN SANCTIONED WORK UNDER GE (EAST) LUCKNOW

Amount

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving not exc 15 cm thickness below and above ground level complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M&L for brick work old size brick sub class 'B' bricks, straight or curved on plan exc 6 m mean radius, built in in CM (1:6) etc complete all as specified and directed.

M&L for brick work with sub class "B' old size brick straight or curved on plan to any radius in half brick thick built in CM 1:4 etc complete all as specified and directed.

M&L for cement concrete type B-1, 1:2:4 (20 mm graded stone aggregate) as in span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for precast concrete slab in cement concrete (1:2:4) Type B1 (20 mm graded stone aggregate) set and jointed in CM 1:6 complete all as specified and directed.

M&L for cleaning of all loose dirt and dust from roof surfaces and 10 mm thick plastering in CM (1:3) using 100 % coarse sand on roof / parapet walls with WPC @ 2 % by weight of cement or as per manufacturer's instruction etc complete all as specified and directed.

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finishing even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in CM 1:6 finishing even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:6 on fair faces of brick work of walls, finished even & smooth without using extra cement etc complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair face of brick work of walls, mixed with water proofing compound (ISI marked) @ 2% by weight of cement or as per manufacturer’s instructions, finished even & smooth without using extra cement complete all as specified. incl mouldings, chamfers, splay rounded or coved angles, beads,grooves and rebate upto 10 cm in width or 15 cm in girth complete all as specified and directed. (Note : - WPC shall be measured and paid for 'separately Only').

M&L continuous brick edging 75mm wide with brick laid on end vertically with sub fly ash brick complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement complete all as specified and directed.

Supply only integral water proofing compound, ISI Marked complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade over a coat of primer complete all as specified and directed.

M&L for preparation and complete removal of existing treatment from old plastered surfaces of walls and applying two coats of oil emulsion distemper (OBD) of approved shade/tint over a coat of primer with 1-2 mm thick birla white care putty on wall/ceiling etc complete all as specified & directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of alkali resistant primer of approved shade/tint complete all as specified and directed.

M&L for preparation & complete removal of existing treatment from old plastered surfaces of wall & applying two coats of cement base paint over a coat o f alkali primer of approved shade over a coat of primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling & applying two coats of white wash, complete all as specified and directed.

M&L for preparation and complete removal of old decorated plastered surfaces of ceilling and applying two coat of white washing on ceilling complete all as specified and directed.

M&L for 1-2mm thick of wall care putty over wall/ceiling surfaces etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

M&L for non skid ceramic tiles (coloured) 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors joints free, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:6, complete all as specified and directed.

M&L for glazed ceramic tiles (coloured) 300x600 x 7mm / 450x300x7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick rendering in cement & sand mortar 1:4, complete all as specified and directed.

S&F steel work in tubular trusses, raft, purlins etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade ST-240 complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete laid over 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for 50 mm thick PCC 1:3:6 type C2 using 40 mm graded crushed stone aggregate as in plinth protection surface finished fair and even without using extra cement complete all as specified and directed. (Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3)).

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any motar etc complete all as specified and directed.

M&L for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 20mm thick screed in CM 1:4 including cutting, polishing, rubbring & moulding of edges complete all as specified and directed.

M&L applying evenly a tack coat of industrial Bitumen 85/25 at the rate of 1.20 kg per sqm including cleaning surfaces as in sunken complete all as specified and directed.

S&F APP based polymeric membrane mimimum weighing 3 kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric land on primed surfaced by forced application complete all as specified and directed.

M&L for aluminium painting over APP membrane on roof surfaces complete all as specified and directed.

Taking up or down steel water tubing and connections of 15mm bore, fixed in walls, ceiling, floors, trenches etc. complete all as specified and directed.

Taking up or down steel water tubing and connections of 20mm bore, fixed in walls, ceiling, floors, trenches etc. complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting not exc 10 cm girth in brick walls complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F sinks made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm , bowl size 410mm x 330mm x 160m including 32mm dia waste pipe of polythelene of low or high density, 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, making holes in walls for brackets and fixed in CM 1:3 or PCC 1:2:4 type B-0, 40mm dia Waste coupling of PTMT (half or full threaded) .(Minimum weight -60 gms) including taking down old unserviceable sink complete all as specified and directed .

S&F in repair long body 15mm bore bib tap, cast copper alloy, chromium plated fancy type with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed.

S&F in repair 15 mm bore brass CP wall mixer for mixing hot & cold water with provision for over head shower with arm and long bend pipe and wall flanged screwed down for iron pipe etc complete all as specified and directed.

S&F in repair cast iron floor trap/nahani trap plan with grating of 100 mm size including jointing to waste pipe with cement joints etc complete all as specified and directed.

Dismantling PVC water tanks and removing for capacity exc 500 litres & not exc 1000 litres etc complete all as specified and directed.

S&F 1000 Litre capacity Rotational moulded polyethylene water storage tanks triple layered in white colour (cylindrical, vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete all as specified and directed.

S&F in repair 20 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20 mm bore complete all as specified and directed.

S&F in repair gun metal gate valve screwed both ends to15mm bore pipe complete all as specified and directed.

Dismantling of cast iron drain pipe jointed in lead joints or cement joints and taking out of under floors if required complete all as specified and directed.

S&F 100 mm dia cast iron soil waste and vent pipes sand cast in any length with or without laid in wall with cement joints complete all as specified and directed.

S&F in repair 100 mm bore cast iron bends of any radius diminshing pieces or tappers (larger bore measured) complete all as specified and directed.

M&L PVC(SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area exc 1.5 sqm but not exc 4 sqm each, complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area not exc 1.5 sqm each, complete all as specified and directed.

Taking down shutters exc 1.0 sqm but not exc 2.0 sqm each and refixing in same opening etc complete all as specified and directed.

Dismantling of boarding, any description, fixed in any position with screws etc complete all as specified and directed.

M&L PCC 1:3:6 type C-1 using 20 mm graded stone aggregate for filling in bed block of hold fast, back filling of chowkhat etc complete all as specified and directed.

M&L for PCC1:3:6 type C-2 using (40mm graded aggregate) as in posts etc complete all as specified and directed.

S&F for pressed steel frames of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, (thickness of sheet shall be 1.25mm) and making good the wall with plaster in CM 1:6 complete all as specified and directed.

S&F for pressed steel frames of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs hinges, locks strike plate etc, (thickness of sheet shall be 1.25mm) and making good the wall with plaster in CM 1:6 complete all as specified and directed.

S&F 35 mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides including mechanically pressed factory made 1 mm thick decorative laminate type-1 both sides of surface finish ,colour and pattern approved complete all as specified and directed.

S&F factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in clause 8.24 (a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkhat, complete all as specified & directed.

S&F powder coating aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F powder coating aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 Kg/m including necessary joining cleats glazing clips rubber packing, anodised aluminium sanp beading screw , anodised aluminium fittings such as peg stays 150 mm long (01 Nos), hinges type B-21 100 mm long (2 Nos) , suitable handles (1 no) complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each pane complete all as specified and directed.

S&F PVC cabinet/CB shutter as in kitchen with frame including shelves in required sizes at site made out of 18mm thick one side decorative lamination & other side balancing lamination sheet and provision of shutters made out of 18mm thick one side decorative laminated PVC sheet all required brackets stainless screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish including all necessary fittings as per site requirement complete all specified and directed . Note:- Density of PVC solid sheet should not be less than 575 kg/cum.

S&F aluminium anodised 100 mm long Butt hinges with galvanised mild steel screws complete all as specified and directed.

S&F butt hinges of size 100 mm medium weight, stainless steel ISI marked complete all as specified and directed.

S&F aluminium handle 125mm size, cast type, anodized (ISI marked) complete all as specified and directed.

S&F aluminium handle 150mm size, cast type, anodized (ISI marked) complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed.

S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified and directed.

S&F 300 mm long mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and directed.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F 150mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F in repair 300mm long stainless steel six peg hanger chromium plated complete all as specified and directed.

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 including welding work complete all as specified & as directed.

S&F mild steel section such as tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade ST-240 complete all as specified and directed.

S&F of MS plate as rest plate of truss forming hole for anchor bolt without any arrangement complete all as specified and directed.

S&F stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire, staples complete all as specified and directed.

M&L for preparation of new surfaces of wood or wood based materials of any description over 10 cm width or girth and applying two coats of synthetic enamel paint of approved tint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel and iron surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint of approved tint over 10 cm in width or girth not otherwise described with red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint complete all as specified and directed.

S&F ball catehes with 8 mm dia steel bal and brass body and strike plate magnet ball catcher for cup board shutters complete all as specified and directed.

Demolition of reinforced cement concrete in floors, beams, chajjas, landing slab in any position or height and similar suspended works complete all as specified and directed.

M&L RCC 1:1.5:3 type B1 nominal mix (using 20 mm graded aggrigate)as in slab, chajjas, beam etc complete all as specified and directed.

M&L for form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exc 200mm thick complete all as specified and directed.

M&L TMT bar 8 to 10mm dia and over, cut to length, bent ot shape required, including cranking, bending , hooking ends and binding with and including mild steel wire(annealed not less than 0.9mm dia) icluding welding,rivetting etc complete all as specified and directed.

S&F cast copper alloy stop valves for 15 mm bore of pipe screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F cast copper alloy stop valves for 20 mm bore of pipe screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair 15 mm dia chromium plated fancy type angle valve pipe with capstan head long screwed shank including CP cover plate etc complete all as specified and directed.

S&F in repair stop valves/angle volve, 15mm dia, cast copper alloy,CP fancy type with long shank and cup(concealed type) screwd down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or for unions complete all as specified and directed.

M&L machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 grade laid over sand cushioning complete all as specified and directed

M&L for grinding and polishing to kota stone flooring complete all as specified and directed.

Excavation in post holes (or similar holes) each not exc 0.50cum, getting out, returning, filling, in and ramming earth or broken rubble mixed with earth arouond in layers not exc. 25cm, watering and removing surplus soil to distance not exc 50 m and making good surface in soft/loose soil complete all as specified and directed.

Excavation in trenches not exc 1.50m wide and not exc 1.50 M depth for foundation etc. and getting out in soft/loose soil complete all as specified and directed.

M&L for PCC (1:5:10) type E-2, using 40mm graded stone aggregates as in foundation filling & mass concrete complete all as specified and directed.

M&L 100mm thick PCC (1:4:8) type D-2, using 40mm graded stone aggregate as in sub base for flooring complete all as specified and directed.

M&L for DPC (1:2:4) type B-0 to horizontal or vertical surfaces including necessary form work 40 mm thick complete all as specified and directed.

M&L hard core using broken bricks of gauge not exc 63 mm deposited spread and levelled in layers not exc 15 cm thick watered and rammed to a true surface complete all as specified and directed.

S&F solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S&F factory made solid panel PVC door shutter 28 to 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail and bottom rail on either side and gap insert for top rail and bottom rail: Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement and fixing in the frame at site complete all as specified and directed.

M&L precast cement concrete louvers and jallies, in PCC 1:2:4 type B0 (12.5 mm graded aggregate) 40 mm thick (measured solid) including all mouldings nut excluding frame and set in CM 1:4 complete all as specified and directed.

S&F vitreous china squatting pan Orissa pattern of size 580mm x 440mm with integral foot rest and 'P' or 'S' trap including Cement concrete bedding , connecting flushing pipe and `P' trap, complete all as specified and directed.

S&F 10 litre capacity PVC valve less syphonic action type flushing cistern low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F 110 mm PVC (SWR ) pipe single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

All as per item No 106 above but fixed on wall

S&F 75 mm PVC (SWR ) pipe single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F 110 mm PVC (SWR ) bend any radius complete all as specified and directed.

S&F 110 mm PVC (SWR ) branch piece single (Single /Double T) equal or unequal complete all as specified and directed.

S&F 75mm PVC (SWR ) vent cowl complete all as specified and directed.

S&F 110 mm PVC (SWR ) reducer complete all as specified and directed.

S&F 75 mm dia cast iron floor trap with grating including jointing to waste pipe in run laid complete all as specified and directed.

M&L returning filling including spreading levelling watering and well ramming in layers not exc 25 cm in soft/loose soil complete all as specified and directed.

M&L removing excavated material not exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

S&F in repair vitreous china white wash hand basin white flat back size 450 x 300 mm excluding waste chain and plug on porcelain stopper butt including brackets complete all as specified and directed.

S&F in repair 15 mm dia bore pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or “cold’ with long screwed shank and flynuts, screwed for iron pipe complete all as specified and directed.

S&F in repair 32 mm bore of pipe low density (LDPE) of pressure rating 6 kg/ sqcm fixed to wall or floor etc including fittings complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail 20 mm dia D type, 60 cm long between flanges complete all as specified and directed.

S&F 125 mm fancy type shower roses brass chromium plated with CP arms for15mm bore GI pipe complete all as specified and directed.

S&F PVC connections 15 mm dia with PTMT Nuts of length for 450 mm long complete all as specified and directed.

S&F vitreous china bowl type urinal flat back size of 465 X 355 X 265 mm white with grating and union for discharge pipe complete with and providing and fixing plugs , bedding against wall in Cm 1:2 , securing urinals to plugs with and including 60 mm long brass screws fixing with brackets, flush pipe etc. complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 for 150mm bore of pipe as concrete bed to drain pipes including packing under and haunchng against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L for salt glazed stoneware drain pipes 150mm grade ‘A’ internal dia laid in trenches and jointed complete all as specified and directed.

M&L for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F power coated (min 50 micron coating) aluminium section as in door frame /partition fully glazed/gauzed/panelled, jointing cleat of fixing etc including handle, tower bolts, hinges, rubber gasket & all necessary accesories complete all as specified and directed.

Providing and fixing powder coated coloured aluminium partly glazesd and partly paneled door shutter standard door section having size of styles, top rails 83x44mm where as bottom rails will be made up of 100x44mm including necessary joining cleats glazing clips, rubber packing, anodized aluminium snap beading screws, anodized aluminium fittings such as 100mm long 3 No. aluminium hinges B-21 ,type 01 No. aluminium tower bolt 200mm long and one no mortise lock 100mm size 4 levers (vertical type) and 01 No 300mm size long aluminium sliding bolt and 02 No fancey type fiber glass 150mm dia circular handle shall be provided to each door and glazing of top panel shall be made of 5.50 thick sheet glass and pannelling shall be provided with 12mm thick exterior grade pre laiminated partical board with both side choice laminations complete all as specified and directed.

S&F aluminium body door closer hydraulically regulated, designation No.3, universal type,suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and directed.

S&F chequered cement concrete tiles 300mmx300mm x 25 mm thick of approved size/design/shade set & jointed in neat cement slurry & pointed in white or coloured cement to match as in floor over and including 20mm thick screed bed in CM 1:4 , complete all as specified and directed.

M&L cement concrete type B-0, 1:2:4 (12.5 mm graded aggregate) on roof slab/kerb/coping complete all as specified and directed.

S&F wire netting/grill of powder coated aluminium 4 mmx 25 mm mesh size complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, socket, bell or power) complete including all electrical fittings & fixtures(DBs, submain,cables etc) and making good disturbed surfaces of wall , floor etc and matching wth original colour of wall, complete all as specified and directed.

Taking down carefully copper/aluminium sub main wiring from existing concealed PVC conduit complete and making good disturbed surfaces of wall, floor etc and matching wth original colour of wall complete all as specified and directed.

Disconnecting/dismantling of old existing unserviceable DB's any way 240 Volts with their unserviceable burnt MCB's/Isolators complete all as specified and directed.

Taking down & re-fixing the same after completion of wiring including connecting of electric connection of ceiling fan/exhaust fan with three core copper flexible wire 23/0.0076 ccomplete all as specified and directed.

M&L for one light/fan/exhaust fan point wiring controlled by one switch with PVC insulated unsheathed multi stranded copper conductor (FRLS) of size 1.5 Sqmm (for Phase colour code Red and for Neutral colour code Black) and one run of size 1.5 Sqmm PVC insulated unsheathed multi stranded copper conductor (FRLS) (as earth wire, colour code green) and connected to common earth dolly all as specified. , drawn through in and including concealed PVC Conduit medium grade, ISI marked not less than 19.5 mm / 20 mm dia along with conduit fixing accessories and with pressed steel terminal box thickness 1.6 mm painted with one coat of black bituminous paint as a primary and two coats of enamel paint with 3 mm thick laminated sheet for provision of switches/regulators as per specified SSR complete all as specified and directed. NOTE:-After rewiring cutting chasing portion should be matched with existing finishes of walls.

All as per item No 137 above but 5 Amp socket outlet, independent.

All as per item No 137 above but on the same board.

All as per item No 137 above but 2.5 sq mm wire for one 15 Amps socket outlet independent with continuous PVC insulated single core green colour copper earth wire of size 1.5 sq mm connected to common earth dolly.

S&F in repair of switch piano flush type 5 Amp one way single pole, 240 volts complete all as specified and directed.

S&F in repair of socket outlet 5 Amp 5 Pin 240 volt flush type complete all as specified and directed.

S&F in repair of switch socket outlet two in one 5 & 15 Amp 6 pin multipurpose combination complete all as specified and directed.

S&F in repair of ceiling fan regulator for 1200mm/1400mm sweep electronic rotary step type 120/280 volts complete all as specified and directed.

S&F in repair ceiling rose two or three terminals surfaces bakelite65 x 50mm size complete all as specified and directed.

S&F lamp holder with back plate suitable for batten fittings (white colour) complete all as specified and directed.

S&F in replacement of single side connection LED T8 tube light rod 20 Watt, 6500K of four feet long into and including LED tube light fixture of four feet long with T8 push fit type holders, connector block, end caps, etc including connecting up complete all as specified and directed.

S&F in repair of LED Mirror light fitting 15 watt(2') with extruded aluminium housing and robust construction complete with inbuilt driver complete all as specified and directed.

S&F in repair of LED street light pressure die cast aluminium housing suitable for 35W IP 66 protection including MS clamps made of 25x3 mm flat iron with bracket of GI pipe light grade 25 mm dia and length not less than 1.2 mtr end of GI pipe complete all as specified and directed.

S&F in repair MCB DB TPN (double door) 4 Ways, 415 Volts including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall complete all as specified and directed.

S&F in repair MCB DB SPN (double door) 8 Ways including bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good surfaces of wall complete all as specified and directed.

S&F single pole and neutral sheet metal enclosure with two pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified and directed.

S&F in replacement MCB, single pole, 240 Volts, of capacity (6-32 Amps) as ordered breaking capacity 10 KA complete all as specified and directed.

S&F in repair MCB SPN, 40 to 63 Amps, 240 Volts , breaking capacity 10KA complete all as specified and directed.

S&F in replacement TPN three pole 415 volts100 Amps repturing capacity 25KA complete all as specified and directed.

M&L for sub main wiring with 04 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 04 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.

M&L for sub main wiring with 06 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 06 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to match the existing including taking out the unserviceable sub main wiring complete all as specified & directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level steel earth plate connected with GI wire 04 mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15 mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150 mm thick around GI earth plate, GI pipe medium grade 20 mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40 mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6 mm dia at the rate of 75 mm centre to centre both way with 12 mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40 mm x 40 mm x 3 mm frame for pit cover including testing on completion complete all as specified and directed.

S&F air freshner fan 200 mm sweep AC 230 volts single phase with louvers including making connection with three core PVC insulated 1100 volts grade multi stranded copper wire of appropriate size including testing complete all as specified and directed.

M&L for wiring with two single core 10 sqmm multi-stranded copper conductor PVC FRLS insulated and unsheathed cable ISI marked drawn through in and including PVC conduit medium grade concealed in wall for sub main connection complete all as specified and directed.

M/S RAJ INTERIORS

QUALITY CONSTRUCTIONS CO

M/S Reliance Construction

rajan construction

M/S SWATI CONSTRUCTION

M/S S S A ASSOCIATES

M/S BABA CONSTRUCTION