PROVN OF ADDN OR ALTN AND AUGMENTATION TO WATER SUPPLY SYSTEM AT BAIRAGARH, BHOPAL

Amount

Note : Plese Ref Sch A / BOQ Notes before quoting the tender, for all Phases / items mentioned below. ITEMS FOR PHASE - I, WORK ( Consisting of Ser item No 2.00 to 136.00)

M&L for excavation in trenches in any type of soils, n.exc 1.5m wide and n.exc. 1.5m wide and 1.5m in depth for foundation ,etc all as specified.

Returning, filling any type in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing any type of excavated material n exc 50m and deposited where directed at a level not exc 1.5 m above the starting point.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone agg) as in foundation , filling, subbase and mass concrete complete all as specified and directed.

M&L TMT steel bars 10 mm dia, and over cut to length,bent to shape required,including cranking,bending spirally for hooping for columns,hookings ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engr in Charge.

Description all as per ser item No 6.00 above but all as per item above but 6 to 8 mm.

Use and waste form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundaiton and plinth beams ; and similar work; vertical or to batter.

Use and waste form work to sides of pillars, posts, struts, piers, columns and stanchions.

Use and waste form work to sides and soffits of floor of roof beams beam haunchings, shelves including supports , over hangs etc.

Use and waste form work to sofits of suspended slabs such as roof slabs, floor slabs n exc 200mm thick

M&L for reinforced cement concrete M-25 (Design mix) in foundation, footings, plinth beam etc all as specifed and directed.

M&L for reinforced cement concrete M-25 (Design mix) in columns etc all as specifed and directed.

M&L for reinforced cement concrete M-25 (Design mix) in beams, cantilivers over 1.5 mtr span.

M&L for reinforced cement concrete M-25 (Design mix) in slabs suported on walls, roofs and shelves.

M&L for PCC 1:3:6 type C-1 as in plinth protection 75mm thick.

M&L for PCC 1:2:4 type C-1 as in Sub floors, 75mm thick.

M&L sand filling under floors or in foundations including watering and consolodation.

M&L for brick work with sub class'B' (modular bricks) straight of curved on plan n exc 6m mean radisu built in modular brick CM 1:6

Description all as per ser item No 19.00 above but as in half brick wall in CM 1:4

M&L for screed bed or bedding layer of mortar 15mm thick (1:4) for laying floor finishes

M&L Machine cut Kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cment slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L Kota stone slab 20-25mm thick in riser of steps , skirting , dado and piller laid over cement screed and jointed with grey cment slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified.

M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed withwhite cement with admisture of pigment to match the shade of granite stone including grinding and polishing types.

M&L for rendering 15 mm thick in cm 1:6 on faces of brick or concrete surfaces and finishing even and smooth complete all as specified and directed by Engr in Charge.

M&L for rendering 15mm thick in cm 1:4 on faces of brick or concrete surfaces and finishing even and smooth complete all as specified and directed by Engr in Charge, including M&L of integral water proffing compound as per manufacturer's instructions.

M&L for rendering 5mm thick in cm 1:3 on ceiling surfaces and finishing even and smooth complete all as specified and directed by Engr in Charge.

M&L for moorum /red bajri filling in floors or pavings, laid in layers n exc 15cm thick in layers,spread,leelled and rammed including watering

M&L for PCC 1:2:4 type B-1 as in 75 mm thick PCC for sub base flooring incl finishing cement concrete surface even & smooth without using extra cement

M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of white cement based Birla wall putty complete all as specified and as directed. Note :-Wall Putty shall be measured and paid seperately.

M&L for preparation of newly plastered or unplastered surfaces of walls and applying three coat white wash complete all as specified and as directed.

M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coat of cement based paint over a coat of white cement based Birla wall puttyall as specified. Note :-Wall Putty shall be measured and paid seperately.

M&L for applying 3mm thick one coat of white wall putty on walls complete all as specified and directed. Make -Birla/JK putty.

S&F 105X60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete as specified made out of 1.25mm thick MS Sheet complete all as specified and as directed.

S&F factory made solid PVC moulded door shutter with particle board core 28 to 30 mm thick (style) with 2,4, or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face and 2mm plain colour PVC sheet on back face complete all as specifed and directed.

S&F steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete including lugs with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F steel windows with side hung shutters including box type hinges with steel handle, and peg stay, complete with wire gauzed bar , dovetailed or welded complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples

S&F 200 mm Aluminium anodised barrel tower bolts extruded section and fixed complete all as specified and directed

S&F 150 mm Aluminium handles, cast type, anodised complete all as specified and directed

S&F 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L framed work such as grills, grating etc with ends of bars shoulderd and /or riveted or forged in to spikes; framed guard bars/angle; and similar work Fe 290 Gde E-165.

S&F sheet glass 3mm thick ordinary quality and glazing with oil putty in Squares n.exc 0.50 sqm in each pane.

M&L for two coats of synthetics enamel paint on steel surfaces over one coat of red oxide primer incl preparation of new steel surfaces

M&L APP base polymeric membrane minimum weighing 3kg/sqm and 3mm thick reinforced with polyester non-woven fabric (wt not less than 150gms/sqm) laid on bitumen 85/25 grade at the rate of 1.2 kg/sqm primer surface by forced application complete all as specified

M&L 10 mm thick plaster in CM 1:4 mixed with and incl water profofing compound @3% by weight of cement applied over roof slab. After the plaster is cured the roof will be tested for water tightening by ponding with water for seven days for any seepage / leakages etc. if any seepage is oberved the rectification will be carried out by pressure grouting under the pressure of 5 Kg/Sqcm using cement based cement grout. After the surface is repaired the slab will be tested for watertightness aginst before processing further treatments. (Water proofing compound measured seperately)

Supply only integral water proofing compound.

M&L for Curtain rod, brass, 20mm dia fancy decorative type

M&L for Curtain rod, brass, 20mm dia bracket pair fancy decorative type

M&L for floor door stopper of aluminium ally body and tongue anodised, with hard drawn steel spring , fixed in floor.

M&L for Treating the bottom and sides of excavation at the rate of 5 litres of emulsion per Sqm of surface area, complete all as specified and directed

M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per Sqm of vertical surface area, complete all as specified and directed

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per Sqm of surface area, complete all as specified and directed

M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per Sqm of surface area, complete all as specified and directed

M&L for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall, complete all as specified and directed

M&L for hard core of gauge n.exc 63mm but n.exc100mm, deposited , spread and levelled in layers n.exc 15cm thick , watered and rolled /rammed to a true surface.

M&L for chequered cement concrete tiles glossy finish size( 20x20cm x25mm thick set jointed and pointed in neat cement slurry with gray cement and pigment over 15mm thick screed bed in CM 1:6 complete all as specifed and directed.

S&F MS steel plain black sheet 0.8mm thick in duct/wall cladding . Steel gate sand similar works cut to size holes punched including round headed screws nails fixed to steel of wood frameing etc. Complete all as specified and directed

M & L for concealed point wiring for light , fan point and bell point with 1.50 sqmm (nominal area), FRLS PVC insulated, unsheathed, single core multi-stranded copper conductor cable, 1100 volts grade,ISI marked controlled by one one-way switch, drawn through and including concealed medium grade PVC conduit not less than 20 mm dia, ISI marked, with all accessories(PVC Casing and caping to be done wherever wiring to be run on ceilings and concrete surfaces including one run of 1.5 sqmm FRLS muti stranded copper conductor (Green colour cable) as earth continuity wire connected to common earth dolly, including sunk sheet steel terminal box made out of 1.20 mm thick and not less than 60 mm in depth GI/MS/ prssed steel terminal box to be conclead in wall, duly painted with two coates of anti corrosive black bituminous paint over a coat of red oxide primer in and out sides and two coated of aluminium paint on internal surface , including laminated hylum sheet cover, ISI marked of Make" Hylem" for mounting of fittings like switches, sockets, fan regulators etc. fixed with galvanised screw and cup washer complete all as specified and directed. Note : Wiring to be done as per arroved colour code in IE rule.Rate includes chase cutting for concealed wiring Make of Cable : Polycab/ L&T/ Havells

Description all as per ser item No 59.00 above but for 3 pin socket outlet, 5 Amp on the same board with other switches, complete all as specified and directed.

Description all as per ser item No 59.00 above, but for 3 pin 5 amp switch socket combination on independent board with other switch complete all as specified and directed.

Description all as per ser item No 59.00 above but wiring with 2.5 Sq mm copper cable for 5/15 amp switch socket combination on independent board and provision of 1.5 Sqmm, FRLS insulated multi-stranded single core earth wire for earth continuity, connected to common earth dolly complete all as specified and directed.

Material and labour for sub-main wiring with 2 runs of 6 sqmm FRLS PVC insulated, multi-stranded, copper cable, 1100 V grade, along with one run of 4.0 sqmm copper cable for earth continuity wire connected to common earth dolly (Colour code to be followed) drawn through concealed 20 mm dia, medium grade, PVC conduit, including accessories complete all as specified and directed .Make of Cable : Polycab/ L&T/ Havells

Supply & Fix light fitting any type and S&F LED 18W / 20 W /21Watt tube light fitting (T 5/T8 type) , including LED retrofit tube 20/21 W one side connection type, 240 v, PF > 0.90, colour Temp 6500 K, System Luminious efficacy > 100Lm/W, complete with powder coated CRCA decorative patti suitable for surface mounting on wall, complete fitting including connecting with PVC insulated multistranded copper flexible cable 0.5 sqmm two core, and PVC round block white colour x 2 Nos for mounting of fitting complete all as specified & directed. Make :-Bajaj ( For Batten Model No. BLRB DB 118 or suitable for mounting T8 LED tube 20 watt and For LED tube Moldel No. BLRB21WCWc) or C&S cat Part No. LTDC01220WLED/WD (LED battan T8 TARA -M) or Havells (Titania LED tube with Regal batten LED) or equivalent in Philips/ Crompton as approved by GE.

S&F Polycarbonate switch piano, flush button, single pole, one way 5 Amp , 240 volts ISI marked, Make Anchor/ Havells/Cona/ Leader (white colur)

Supply and fixing, Polycarbonate ceiling rose, surface type, 3 terminal, 240 , ISI marked, Make Anchor/Havells/ Cona/ Leader (white colur)

Supply and fixing Polycarbonate socket outlet 2-in-1, 5 pin 5 Amps, 240 volts, flush type Make Anchor/Havells/ Cona/ Leader (white colur)

S&F with socket outlet flush type multipurpose 2 in 1, 3 pin 5 and 15 Amp, 230 volts complete as directed.

S&F Polycarbonate switch piano flush button single pole one way 15 Amp 240 volt ISI marked, Make Anchor/Havells/ Cona/ Leader (white colur)

S&F, stepped type electronic fan regulator, Delux model, 100 watt, 240V, flush type. Make Anchor/ Havells/Cona/ Leader (white colur)

S & F Lamp holder, insulated body with back plate suitable for batten/angular fittings fixed complete.Make Anchor/Havells/ Cona/ Leader (white colur) with LED lamp of 9 watt (of make : Philips/Bajaj/CG)

Supply laying and testing cable XLPE insulated screened PVC bedded, galvanized 1100 Volt grade with 16 Sqmm 4 core.

Supply and fixing double door MCB DB,VTPN, 4 way, 440 volts grade, with 200 amps rated bus bar with MCB as incommer and MCB as outgoing.complete fitted on wooden board first class of suitable size complete all as specified and directed by EIC . Make- Legrand/ L&T/C&S.

Supply and fixing, flush to wall, double door MCB DB, SPN 8 way, 240 volts grade, with 200 amps rated bus bar. of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete fitted on wooden board first class of suitable size complete all as specified and directed by EIC. Make- Legrand/ L&T/C&S

S & F MCB SPN 5 to 40 amps 10 KA ,c-series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-In-Charge. Make- Legrand/ L&T/C&S

S&F MCB SP 240 volts 5 to 40 Amps, 10 KA breaking capacity, 'c' curve including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-In-Charge. Make- Legrand / L&T / C&S

S & F MCB TPN 63 Amps 10 KA including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-In-Charge. Make- Legrand / L&T / C&S

S & F Ceiling fan of AC single phase 230/240 V of size 1200 mm sweep and electric connection with 1.5 Sqmm three core PVC insulated round flexible copper conductor and sheathed cable complete all as specified and directed by Engr-In - Charge. Make: Crompton / Bajaj / Havells.

M & L for Earthing complete with galvanized steel earth plate electrode 60cm x 60cmx 6.3 mm thick buried directly in ground ( earth pit not less than 2.25 meter deep below ground level) with the top edge of the earth plate not less than 1.5 meter below normal ground level connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or of steel all as shown in electrical plate No.5 of MES SSR parts-I and including excavation & earth work in any type of soil , disposal of soil , providing alternate layers of charcoal and common salt, construction of PCC earth chamber in mix 1:3:6 type c-1 with 40 mm thick RCC 1:2:4 type B-J cover reinforced with 8mm dia MS bars both ways with lift hook made out of 8 mm dia bar, watering arrangement with funnel and wiremesh and watering pipe of 20mm dia GI light grade and 15mm dia light grade pipe for earth lead protection and testing on completion, complete all as specified and directed.(Note: Unit rate of earthing deemed to be included with GI wire 4 mm, GI pipe light grade protection pipe 15 mm up to 7.5 RM)

Taking down carefully old sluice valves/ Gate Valve of size 80 mm. dia complete all as specified and directed.

Taking down carefully old sluice valves / Gate Valve of size 100 mm. dia complete all as specified and directed.

Taking down carefully old sluice valves / Gate Valve of size 150 mm. dia complete all as specified and directed.

Taking down carefully old sluice valves / Gate Valve of size 200 mm. dia complete all as specified and directed.

Taking down carefully old sluice valves / Gate Valve of size 250 mm. dia complete all as specified and directed.

Taking up / down existing , cast iron pipe lines/ water mains of any description /grade and in position including all fittings, accessories and fixtures etc existing in between pipe line , by taking out and opening any type of joints (Tyton / Gasket/ Lead Joint) complete all as specified and directed by the Engineer -in- Charge for following bore of pipes :-

a) 250 mm bore

b) 150 mm bore

c) 100 mm bore

Supply ,Laying, connecting jointing and testing Ductile iron pressure pipes ISI maked to IS -8329-2000 (Reaffiremed -2005 Edition 4.1 of dia 250 mm with socket tyton joint, suitable for " Push on joints" in standard working length supplied with rubber gasket duly ISI marked for water supply,class K-9 with socket and with cement mortor lining inside the metalic zinc coating with finishing layer of bituminous paint on outside the pipe without polythelene paint on outside the pipe without polythene sleeves with and including "Push on joint" supplied with ISI marked EPDM rebber gasket conforming to IS -5382-1985 (Reaffirmed 2003) with haedness of type -2 (bulb) and type -5 (Heel) puality laid in trench pipe complete all as specified and directed :- MAKE:-ELECTROSTEEL /JINDAL / ELECTROTHERM (INDIA) LTD NOTE :- Earth work, and DI specials/ fittings of the pipes shall be measured and paid for separately under appropriate item of BOQ/Schedule `A'.

Supply ,Laying, connecting jointing and testing Ductile iron pressure pipes ISI maked to IS -8329-2000 (Reaffiremed -2005 Edition 4.1 of dia 150 mm with socket tyton joint, suitable for " Push on joints" in standard working length supplied with rubber gasket duly ISI marked for water supply,class K-9 with socket and with cement mortor lining inside the metalic zinc coating with finishing layer of bituminous paint on outside the pipe without polythelene paint on outside the pipe without polythene sleeves with and including "Push on joint" supplied with ISI marked EPDM rebber gasket conforming to IS -5382-1985 (Reaffirmed 2003) with haedness of type -2 (bulb) and type -5 (Heel) puality laid in trench pipe complete all as specified and directed :- MAKE:-ELECTROSTEEL /JINDAL / ELECTROTHERM (INDIA) LTD NOTE :- Earth work, and DI specials/ fittings of the pipes shall be measured and paid for separately under appropriate item of BOQ/Schedule `A'.

Supply ,Laying, connecting jointing and testing Ductile iron pressure pipes ISI maked to IS -8329-2000 (Reaffiremed -2005 Edition 4.1 of dia 100 mm with socket tyton joint, suitable for " Push on joints" in standard working length supplied with rubber gasket duly ISI marked for water supply,class K-7 with socket and with cement mortor lining inside the metalic zinc coating with finishing layer of bituminous paint on outside the pipe without polythelene paint on outside the pipe without polythene sleeves with and including "Push on joint" supplied with ISI marked EPDM rebber gasket conforming to IS -5382-1985 (Reaffirmed 2003) with haedness of type -2 (bulb) and type -5 (Heel) puality laid in trench pipe complete all as specified and directed :- MAKE:-ELECTROSTEEL /JINDAL / ELECTROTHERM (INDIA) LTD NOTE :- Earth work, and DI specials/ fittings of the pipes shall be measured and paid for separately under appropriate item of BOQ/Schedule `A'.

Supply ,Laying, connecting jointing and testing Ductile iron pressure pipes ISI maked to IS -8329-2000 (Reaffiremed -2005 Edition 4.1 of dia 100 mm with socket tyton joint, suitable for " Push on joints" in standard working length supplied with rubber gasket duly ISI marked for water supply,class K-9 with socket and with cement mortor lining inside the metalic zinc coating with finishing layer of bituminous paint on outside the pipe without polythelene paint on outside the pipe without polythene sleeves with and including "Push on joint" supplied with ISI marked EPDM rebber gasket conforming to IS -5382-1985 (Reaffirmed 2003) with haedness of type -2 (bulb) and type -5 (Heel) puality laid in trench pipe complete all as specified and directed :- MAKE:-ELECTROSTEEL /JINDAL / ELECTROTHERM (INDIA) LTD NOTE :- Earth work, and DI specials/ fittings of the pipes shall be measured and paid for separately under appropriate item of BOQ/Schedule `A'.

S&F DI fittings such as Bends, tappers, straight connecting piece, Tee pieces ,either one side flanged other socketed/both flanged /both socketed any type, radius and upto 450 mm bore including nut bolt, packing material etc and making the joint leak proof complete all as specified and directed.

Supply & Fix air release valve jointing and testing, of 100 mm approved quality cast iron air release valve, heavy duty, ISI Marked including nuts, bolts, rubber gasket, etc completeall as specified and directed.

Supply, Installation, Testing and Commissioning of PLC (Programmable Logic Controller) based Indoor Monitoring / Annunciating Control Panel with inbuilt wireless DUAL SIM Card GPRS communication modem and suitable antenna (at Filter Plant Sump 1.5 L/G) for Automatic Pump and Valve Control / Protection suitable for 03 nos. Pumps, 07nos. Motorized Valves (+01 Spare), 03 nos. Pressure Switches, 03 nos. priming motorised valves, 03 nos. air release Solenoid Valves, 03 nos. Ultrasonic level Sensors. The panel should be of minimun size 1000mm(h) x 600mm(w) x 250mm(d) (as required for easy operation) fabricated from 2.0 mm thick CRCA sheet and properly powder coated. It shall be floor mounted on properly powder coated sheet metal stand of suitable size. The Panel should be capable of carrying out the below mentioned activities (a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention (h) Manual Mode OperationThe PLC based Panel shall consist of (i) 01 No. PLC with following specifications; (a) PLC should be suitable no. of Digital / Analog inputs / outputs (b) 2 serial ports supporting open communication protocol, (c) Programming software based on IEC to facilitate building of custom built function blocks

Supply, Installation, Testing and Commissioning of PLC (Programmable Logic Controller) based Indoor Monitoring / Annunciating Control Panel with inbuilt wireless DUAL SIM Card communication modem and suitable antenna (at Filter Plant 3 L/G) for Automatic Pump and Valve Control / Protection suitable for 04 nos. Pumps, 10 nos. Motorized Valves (+02 Spare), 04 nos. Pressure Switches and 01no. Ultrasonic level Sensor. The panel should be of minimun size 1000mm(h) x 600mm(w) x 250mm(d) (as required for easy operation) fabricated from 2.0 mm thick CRCA sheet and properly powder coated. It shall be floor mounted on properly powder coated sheet metal stand of suitable size. The Panel should be capable of carrying out the below mentioned activities (a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention (h) Manual Mode OperationThe PLC based Panel shall consist of (i) 01 No. PLC with following specifications; (a) PLC should be suitable no. of Digital / Analog inputs / outputs (b) 2 serial ports supporting open communication protocol, (c) Programming software based on IEC to facilitate building of custom built function blocks

Supply, Installation, Testing and Commissioning of PLC (Programmable Logic Controller) based Indoor Monitoring / Annunciating Control Panel with inbuilt wireless DUAL SIM Card communication modem and suitable antenna (at Filter Plant 1.0 L/G) for Automatic Pump and Valve Control / Protection suitable for 02 nos. Pumps, 4 nos. Motorized Valves (+01 Spare) 02 nos. Pressure Switches and 01no. Ultrasonic level Sensor. The panel should be of minimun size 1000mm(h) x 600mm(w) x 250mm(d) (as required for easy operation) fabricated from 2.0 mm thick CRCA sheet and properly powder coated. It shall be floor mounted on properly powder coated sheet metal stand of suitable size. The Panel should be capable of carrying out the below mentioned activities (a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention (h) Manual Mode OperationThe PLC based Panel shall consist of (i) 01 No. PLC with following specifications; (a) PLC should be suitable no. of Digital / Analog inputs / outputs (b) 2 serial ports supporting open communication protocol, (c) Programming software based on IEC to facilitate building of custom built function blocks

Supply, Installation, Testing and Commissioning of PLC (Programmable Logic Controller) based Outdoor Monitoring / Annunciating Control Panel with inbuilt wireless DUAL SIM Card communication modem and suitable antenna (at BM Qtr ORs/JCO OHT) for Automatic Valve Control / Protection suitable for 08 no. Motorized Valve (+02 Spare) and 01 no. Ultrasonic level Sensor. The panel should be of minimun size 1000mm(h) x 600mm(w) x 250mm(d) (as required for easy operation) fabricated from 2.0 mm thick CRCA sheet and properly powder coated. It shall be floor mounted on properly powder coated sheet metal stand of suitable size. The Panel should be capable of carrying out the below mentioned activities (a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention (h) Manual Mode OperationThe PLC based Panel shall consist of (i) 01 No. PLC with following specifications; (a) PLC should be suitable no. of Digital / Analog inputs / outputs (b) 2 serial ports supporting open communication protocol, (c) Programming software based on IEC to facilitate building of custom built function blocks

Supply, Installation, Testing and Commissioning of PLC (Programmable Logic Controller) based Outdoor Monitoring / Annunciating Control Panel with inbuilt wireless DUAL SIM Card communication modem and suitable antenna (at ITV AREA) for Automatic Valve Control / Protection suitable for 01 no. Motorized Valve (+01 Spare) . The panel should be of minimun size 1000mm(h) x 600mm(w) x 250mm(d) (as required for easy operation) fabricated from 2.0 mm thick CRCA sheet and properly powder coated. It shall be floor mounted on properly powder coated sheet metal stand of suitable size. The Panel should be capable of carrying out the below mentioned activities (a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention (h) Manual Mode OperationThe PLC based Panel shall consist of (i) 01 No. PLC with following specifications; (a) PLC should be suitable no. of Digital / Analog inputs / outputs (b) 2 serial ports supporting open communication protocol, (c) Programming software based on IEC to facilitate building of custom built function blocks

Supply, Installation, Testing and Commissioning of PLC (Programmable Logic Controller) based Outdoor Monitoring / Annunciating Control Panel with inbuilt wireless DUAL SIM Card communication modem and suitable antenna (at BM Qtr ORs/JCO OHT) for Automatic Valve Control / Protection suitable for 08 no. Motorized Valve (+02 Spare) and 01 no. Ultrasonic level Sensor. The panel should be of minimun size 1000mm(h) x 600mm(w) x 250mm(d) (as required for easy operation) fabricated from 2.0 mm thick CRCA sheet and properly powder coated. It shall be floor mounted on properly powder coated sheet metal stand of suitable size. The Panel should be capable of carrying out the below mentioned activities (a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention (h) Manual Mode OperationThe PLC based Panel shall consist of (i) 01 No. PLC with following specifications; (a) PLC should be suitable no. of Digital / Analog inputs / outputs (b) 2 serial ports supporting open communication protocol, (c) Programming software based on IEC to facilitate building of custom built function blocks

Supply, Installation, Testing and Commissioning of PLC (Programmable Logic Controller) based Indoor Monitoring / Annunciating Control Panel with inbuilt wireless DUAL SIM Card communication modem and suitable antenna (at TRS / 68 Engineer Pump House) for Automatic Pump and Valve Control / Protection suitable for 02 nos. Pumps , 03 no. Borewell, 06 nos. Motorized Valves (+02 Spare), 02 nos. Pressure Switches, 01 no. Flow Switch and 02 nos. Ultrasonic level Sensors.The panel should be of minimun size 1000mm(h) x 600mm(w) x 250mm(d) (as required for easy operation) fabricated from 2.0 mm thick CRCA sheet and properly powder coated. It shall be floor mounted on properly powder coated sheet metal stand of suitable size. The Panel should be capable of carrying out the below mentioned activities (a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention (h) Manual Mode OperationThe PLC based Panel shall consist of (i) 01 No. PLC with following specifications; (a) PLC should be suitable no. of Digital / Analog inputs / outputs (b) 2 serial ports supporting open communication protocol, (c) Programming software based on IEC to facilitate building of custom built function blocks

Supply, Installation, Testing and Commissioning of PLC (Programmable Logic Controller) based Outdoor Monitoring / Annunciating Control Panel with inbuilt wireless DUAL SIM Card communication modem and suitable antenna (at Vijay Enclave OHT) for Automatic Valve Control / Protection suitable for 03 nos. Motorized Valves (+01 Spare) and 01 no. Ultrasonic level Sensor. The panel should be of minimun size 1000mm(h) x 600mm(w) x 250mm(d) (as required for easy operation) fabricated from 2.0 mm thick CRCA sheet and properly powder coated. It shall be floor mounted on properly powder coated sheet metal stand of suitable size. The Panel should be capable of carrying out the below mentioned activities (a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention (h) Manual Mode OperationThe PLC based Panel shall consist of (i) 01 No. PLC with following specifications; (a) PLC should be suitable no. of Digital / Analog inputs / outputs (b) 2 serial ports supporting open communication protocol, (c) Programming software based on IEC to facilitate building of custom built function blocks

Supply, Installation, Testing and Commissioning of PLC (Programmable Logic Controller) based Indoor Monitoring / Annunciating Control Panel with inbuilt wireless DUAL SIM Card communication modem and suitable antenna (at New MH Pump House) for Automatic Pump and Valve Control / Protection suitable for 02 nos. Pumps, 09nos. Motorized Valves (+01 Spare), 02 nos. Pressure Switches, 02 nos. priming motorised valves, 02 nos. air release Solenoid Valves and 02 nos. Ultrasonic level Sensors. The panel should be of minimun size 1000mm(h) x 600mm(w) x 250mm(d) (as required for easy operation) fabricated from 2.0 mm thick CRCA sheet and properly powder coated. It shall be floor mounted on properly powder coated sheet metal stand of suitable size. The Panel should be capable of carrying out the below mentioned activities (a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention (h) Manual Mode OperationThe PLC based Panel shall consist of (i) 01 No. PLC with following specifications; (a) PLC should be suitable no. of Digital / Analog inputs / outputs (b) 2 serial ports supporting open communication protocol, (c) Programming software based on IEC to facilitate building of custom built function blocks

Supply, Installation, Testing and Commissioning of PLC (Programmable Logic Controller) based Indoor Monitoring / Annunciating Control Panel with inbuilt wireless DUAL SIM Card communication modem and suitable antenna (at MES Colony Pump House) for Automatic Pump and Valve Control / Protection suitable for 01 no. Pump, 09 nos. Motorized Valves (+01 Spare), 01 no. Pressure Switch and 02 nos. Ultrasonic level Sensors. The panel should be of minimun size 1000mm(h) x 600mm(w) x 250mm(d) (as required for easy operation) fabricated from 2.0 mm thick CRCA sheet and properly powder coated. It shall be floor mounted on properly powder coated sheet metal stand of suitable size. The Panel should be capable of carrying out the below mentioned activities (a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention (h) Manual Mode OperationThe PLC based Panel shall consist of (i) 01 No. PLC with following specifications; (a) PLC should be suitable no. of Digital / Analog inputs / outputs (b) 2 serial ports supporting open communication protocol, (c) Programming software based on IEC to facilitate building of custom built function blocks

Supply, Installation, Testing and Commissioning of PLC (Programmable Logic Controller) based Indoor Monitoring / Annunciating Control Panel with inbuilt wireless DUAL SIM Card communication modem and suitable antenna (at Borewell No.10) for Automatic Borewell Control / Protection suitable for 02 nos. Borewell and 02 nos. Flow Switches. The panel should be of minimun size 1000mm(h) x 600mm(w) x 250mm(d) (as required for easy operation) fabricated from 2.0 mm thick CRCA sheet and properly powder coated. It shall be floor mounted on properly powder coated sheet metal stand of suitable size. The Panel should be capable of carrying out the below mentioned activities (a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention (h) Manual Mode OperationThe PLC based Panel shall consist of (i) 01 No. PLC with following specifications; (a) PLC should be suitable no. of Digital / Analog inputs / outputs (b) 2 serial ports supporting open communication protocol, (c) Programming software based on IEC to facilitate building of custom built function blocks

Supply, Installation, Testing and Commissioning of PLC (Programmable Logic Controller) based Indoor Monitoring / Annunciating Control Panel with inbuilt wireless DUAL SIM Card communication modem and suitable antenna (at Borewell No.11) for Automatic Borewell Control / Protection suitable for 01 no. Borewell and 01 no. Pressure Switch.The panel should be of minimun size 1000mm(h) x 600mm(w) x 250mm(d) (as required for easy operation) fabricated from 1.6 mm thick CRCA sheet and properly powder coated. It shall be floor mounted on properly powder coated sheet metal stand of suitable size. The Panel should be capable of carrying out the below mentioned activities (a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention (h) Manual Mode OperationThe PLC based Panel shall consist of (i) 01 No. PLC with following specifications; (a) PLC should be suitable no. of Digital / Analog inputs / outputs (b) 2 serial ports supporting open communication protocol, (c) Programming software based on IEC to facilitate building of custom built function blocks

Supply, Installation, Testing and Commissioning of PLC (Programmable Logic Controller) based Indoor Monitoring / Annunciating Control Panel with inbuilt wireless DUAL SIM Card communication modem and suitable antenna (at 21 CGSR Pump House) for Automatic Pump and Valve Control / Protection suitable for 02 nos. Pumps, 09 nos. Motorized Valves (+01 Spare), 02 nos. Pressure Switches and 03 nos. Ultrasonic level Sensors. The panel should be of minimun size 1000mm(h) x 600mm(w) x 250mm(d) (as required for easy operation) fabricated from 1.6 mm thick CRCA sheet and properly powder coated. It shall be floor mounted on properly powder coated sheet metal stand of suitable size. The Panel should be capable of carrying out the below mentioned activities (a) Water Level Sensing & Display (b) Pump On/Off (c) Auto priming (d) Operation of Motor Actuated Butterfly Valves (e) Automatic Toggling of Pumps (f) Auto Change Over In Case of Pump Failure (g) Single Phasing Prevention (h) Manual Mode OperationThe PLC based Panel shall consist of (i) 01 No. PLC with following specifications; (a) PLC should be suitable no. of Digital / Analog inputs / outputs (b) 2 serial ports supporting open communication protocol, (c) Programming software based on IEC to facilitate building of custom built function blocks

Supply, Installation, Testing, Commissioning and Programming of Engineering Control station comprising of 1) Supply of Integrated Smart Station platform includes SCADA (multiple acess) having modules for monitoring and / or control of various services viz complete all as specified and directed.. a. Water Supply - Pumping & Distribution b. Electric Supply (i) HT and LT distribution (ii) Streel lights (iii) Diesel Gensets (iv) Automatic Meter Reading and Billing c. STP d. Fire Fighting e. Solar Plants f. Complaint Monitoring and Disposal System. The Smart Station Platform shall be user configurable wth respect to all critical features viz. Landing page, drop down tabs and menus, report formats, alerts and notifications. Make: Net Solutions / Recktronic Devices and Systems / Revolution Info Systems/Universal Switch Gear Control /SECO Make for SCADA: Wincc/ Mitsubishi/ Rockwell Automation/ Cimplicity / Schneider Electric Note: The scope of work includes Provision of new wired broad band connection along with static IP in the name of GE along with call costs for a period of 33 months including suitable the internet charges for 33 months(for phase 2 to phase 4). This IP address shall be used for GPRS communication between the SCADA based Engineering control Center & the PLC based Panels.

Item No 105.00 Contd The scope of work includes: Services for programming, configuration and customisation of the Smart Station Platform with respect to the Water supply Module as per actual site conditions and requirement of the engineer. a. Landing Page to depict criritcal paramters viz. - Level of water in all tanks, pump status ON/OFF/FAIL and Water Quality parameters b. Creation of drop down tabs to monitor the all Pump houses and Remote PLC Panel systems individually c. Creation of individual PLC Panel wise schematics and layouts for the Water Supply system as per the actual site including display of all relevant parameters viz. Water level, Pump ON/OFF/FAIL status, Valve OPEN/CLOSE/FAIL status d. Soft keys for remote manual operation of all pumps and motorised valves from the Master Control station. e. Creation of Day wise Reports for (but not limited to) (i) Run hours of pumps, (ii) Pump / valve operation faliures, etc. in user defined formats using the reporting software of the Smart station including plotting against preset benchmarks. f. Configuring notifications, alerts and alarms as per preset logic. (g) OPC server for unlimited tags with MODBUS TCP/equivalent driver having provision for IOT gateway to exchange data between the PLC based panels and the SCADA system.Make: Kepware, Matrikon,Schneider Electirc, Matsubishi, Siemens, ABB (h) IOT Gateway to be able send the OPC data to a broker on the central server using the latest MQTT protocol working on a Publish Subscribe Model. The IOT gateway shall be able to support 5000 tags. Make Kepware , Matrikon, Schneider Electirc, Matsubishi, Siemens, ABB (j) MQTT broker at the central server to service publish and subscribe requests from the OPC server and the web clients Make : Hive, Mosquito, Eclipse, Revolution Infosystems, Schneider Electirc, Matsubishi, Siemens, ABB (k) Personal computer as Central Server for Development version of the SCADA software and the reporting software with the following detailed specifications INTEL CORE I7 (2120) / 8 GB RAM / 1TB HDD/ WIRELESS KEYBOARD/MOUSE with Microsoft Windows 10 and 22 inches Monitor.(Make -Iball/Dell/Cagitech) Make: Dell/Lenovo/Samsung/Hp/Compaq/LG (l) 600 VA UPS Make: APC/Tata Liebert (m) A4 size Monochrome Printer Make: Cannon/HP/Samsung (n) Antivirus genuine copy Make: Quick heal/Avast/Mac Afee/ Norton

Supply, Installation, Testing, Commissioning and Programming of Smartphone App for Android Operating Systems consisting of min 20 screens with user defined data to displayed complete all as specified and directed. Make: Schneider Electirc/ Matsubishi / Siemens / ABB

Supply installation testing and commissioning of PLC based Graphic Mimic Panel with appropriate number of inputs and outputs and 7'' Colour touch screen HMI with minimum 2 nos. serial ports and 1 no. USB port. The Panel shall be of suitable size, made out of Aluminium / CRCA sheet steel that shall clearly depict the entire layout of the water supply system. The same shall include pump status, valve status, level of tanks, etc. The panel should display in real time the level of water in all automated OHTs and under ground sump. This shall be an online indication panel complete all as specified and directed. Make: - Recktronic Devices and system / CIMCON / SEEPL/ SECO/ Universal Switch Rear Control or any other equivalent of PLC based control panel make approved by E-in-C’s Branch

Supply, Installing,Testing and Commissioning of Ultrasonic Level Transmitter (for measurement of level in Clear Water Tanks & OHTs) - including all accessories complete all as specified & diected. Make: BANNER// NIVELCO / SIEMENS /Universal Switch Gear Control. Range : 0-5 meters Accuracy : 0.5 % minimum Supply Voltage : 24V dc Output : 4-20 mA

Supply, Installation, Testing and Commissioning of Pressure Switch along with all necessary installation accessories like GI barrel piece, double nipple etc. having range 0-6 sq cm. With Weather proof enclosure complete all as specified & diected. Make: DANFOSS / SWITZER / SIEMENS/ Universal Switch Gear Control

Supply, Installation, Testing and Commissioning of Flow Switch along with all necessary installation accessories complete all as specified & diected.Make: DANFOSS / SWITZER / SIEMENS / RAPID CONTROL / JOHNSON CONTROL/ Universal Switch Gear Control

Supply, installation, testing and commissioning of 10 mm dia Brass / SS, direct Acting / Diaphragm type pilot operated Solenoid Valve for air release with manual bypass arrangement along with all necessary installation accessories like gate valve, barrel piece, double nipple, elbows/bends etc. suitable for line pressure of 4 kg/sqcm complete all as specified & diected. Make: AVCON/ ROTEX/ DANFOSS/ SIEMENS/ SWITZER/ Universal Switch Gear Control

Supply, installation, testing and commissioning of 25 mm single phase motorised ball Valve for priming and with manual bypass arrangement along with all necessary installation accessories like gate valve, barrel piece, double nipple, elbows/bends etc. suitable for line pressure of 4 kg/sqcm complete all as specified & diected. Make: JOHNSON CONTROLS/ RITE TORK / EMTORK Universal Switch Gear Control

Supply, Installation, Testing and Commissioning of 80 mm dia, single phase, Motor Actuated Butterfly valve rating PN 16 with disc material of CI with nylon coating, hand wheel for manual operation and having 02 nos. limit switches for Open / Close condition, valve position indicator with output of 4-20mA, inbuilt wireless modem compatibility.In built Serial / USB communication Port, In built data logger with memory, In built SD Card, In built bluetooth transceiver with capability of pairing with any android based smart phone to download logged data. The mounting shall be direct on valve type complete all as specified & diected. Make: RITE TORK / HASEL HOFENER / EMTORK/ Universal Switch Gear Control /SECO

Supply, Installation, Testing and Commissioning of 80 mm dia, single phase, Motor Actuated Butterfly valve rating PN 16 with disc material of CI with nylon coating, hand wheel for manual operation and having 02 nos. limit switches for Open / Close condition, valve position indicator with output of 4-20mA, inbuilt wireless modem compatibility. In built Serial / USB communication Port, In built data logger with memory, In built SD Card, In built bluetooth transceiver with capability of pairing with any android based smart phone to download logged data.The mounting shall be indirect type using specialized extended type arrangement of GI pipe / plate of suitable size/thickness, angle irons and indirect mounting adaptors including raising of existing chamber if required so that actuator mounting is at least 12 inches above ground level complete all as specified & diected. Make: RITE TORK / HASEL HOFENER / EMTORK/ Universal Switch Gear Control /SECO

Supply, Installation, Testing and Commissioning of 100 mm dia, single phase, Motor Actuated Butterfly valve rating PN 16 with disc material of CI with nylon coating, hand wheel for manual operation and having 02 nos. limit switches for Open / Close condition, valve position indicator with output of 4-20mA, inbuilt wireless modem compatibility. In built Serial / USB communication Port, In built data logger with memory, In built SD Card, In built bluetooth transceiver with capability of pairing with any android based smart phone to download logged data.The mounting shall be direct on valve type complete all as specified & diected. Make: RITE TORK / HASEL HOFENER / EMTORK/ Universal Switch Gear Control /SECO

Supply, Installation, Testing and Commissioning of 100 mm dia, single phase, Motor Actuated Butterfly valve rating PN 16 with disc material of CI with nylon coating, hand wheel for manual operation and having 02 nos. limit switches for Open / Close condition, valve position indicator with output of 4-20mA, inbuilt wireless modem compatibility. In built Serial / USB communication Port, In built data logger with memory, In built SD Card, In built bluetooth transceiver with capability of pairing with any android based smart phone to download logged data.The mounting shall be indirect type using specialized extended type arrangement of GI pipe / plate of suitable size/thickness, angle irons and indirect mounting adaptors including raising of existing chamber if required so that actuator mounting is at least 12 inches above ground level complete all as specified & diected. Make: RITE TORK / HASEL HOFENER / EMTORK/ Universal Switch Gear Control /SECO

Supply, Installation, Testing and Commissioning of 150 mm dia, single phase, Motor Actuated Butterfly valve rating PN 16 with disc material of CI with nylon coating, hand wheel for manual operation and having 02 nos. limit switches for Open / Close condition, valve position indicator with output of 4-20mA, inbuilt wireless modem compatibility.In built Serial / USB communication Port, In built data logger with memory, In built SD Card, In built bluetooth transceiver with capability of pairing with any android based smart phone to download logged data. The mounting shall be direct on valve type complete all as specified & diected. Make: RITE TORK / HASEL HOFENER / EMTORK/ Universal Switch Gear Control /SECO

Supply, Installation, Testing and Commissioning of 150 mm dia, single phase, Motor Actuated Butterfly valve rating PN 16 with disc material of CI with nylon coating, hand wheel for manual operation and having 02 nos. limit switches for Open / Close condition, valve position indicator with output of 4-20mA, inbuilt wireless modem compatibility. In built Serial / USB communication Port, In built data logger with memory, In built SD Card, In built bluetooth transceiver with capability of pairing with any android based smart phone to download logged data. The mounting shall be indirect type using specialized extended type arrangement of GI pipe / plate of suitable size/thickness, angle irons and indirect mounting adaptors including raising of existing chamber if required so that actuator mounting is at least 12 inches above ground level complete all as specified & diected. Make: RITE TORK / HASEL HOFENER / EMTORK/ Universal Switch Gear Control /SECO

Supply, Installation, Testing and Commissioning of 200 mm dia, single phase, Motor Actuated Butterfly valve rating PN 16 with disc material of CI with nylon coating, hand wheel for manual operation and having 02 nos. limit switches for Open / Close condition, valve position indicator with output of 4-20mA, inbuilt wireless modem compatibility.In built Serial / USB communication Port, In built data logger with memory, In built SD Card, In built bluetooth transceiver with capability of pairing with any android based smart phone to download logged data. The mounting shall be indirect type using specialized extended type arrangement of GI pipe / plate of suitable size/thickness, angle irons and indirect mounting adaptors including raising of existing chamber if required so that actuator mounting is at least 12 inches above ground levelcomplete all as specified & diected. Make: RITE TORK / HASEL HOFENER / EMTORK/ Universal Switch Gear Control /SECO

Supply, Installation, Testing and Commissioning of 250 mm dia, single phase, Motor Actuated Butterfly valve rating PN 16 with disc material of CI with nylon coating, hand wheel for manual operation and having 02 nos. limit switches for Open / Close condition, valve position indicator with output of 4-20mA, inbuilt wireless modem compatibility. In built Serial / USB communication Port, In built data logger with memory, In built SD Card, In built bluetooth transceiver with capability of pairing with any android based smart phone to download logged data.The mounting shall be indirect type using specialized extended type arrangement of GI pipe / plate of suitable size/thickness, angle irons and indirect mounting adaptors including raising of existing chamber if required so that actuator mounting is at least 12 inches above ground levelcomplete all as specified & diected. Make: RITE TORK / HASEL HOFENER / EMTORK/ Universal Switch Gear Control /SECO

Supplying and fixing 2 x 1.5 sq. mm. PVC insulated and PVC sheathed armoured copper cable etc. as reqd for following size complete all as specified and directed. Note:- Excavation and earth work shall be measured and paid seperately Make: Finolex/Polycab/Havells

Supplying and fixing 4 x 1.5 sq. mm. PVC insulated and PVC sheathed armoured copper cable etc. as reqd for following size complete all as specified and directed. Note:- Excavation and earth work shall be measured and paid seperately Make: Finolex/Polycab/Havells

Supplying and fixing 6 x 1.5 sq. mm. PVC insulated and PVC sheathed armoured copper cable etc. as reqd for following size complete all as specified and directed. Note:- Excavation and earth work shall be measured and paid seperately Make: Finolex/Polycab/Havells

Supply and laying dry river sand for cable cushioning in trenches to required width at bottom and top of cable including spreading levelling watering and consiolidation complete all as specified and directed by Engineer-in-charge. Note:- Punned thickness only shall be measured and paid.

Brick protection with subclass ‘B’ bricks old size, laid dry, flat over cable perpendicular across the cable in trenches complete all as specified.

S&F GI tubing light grade 50mm bore protection for cable under roads, crossings/culverts incl jointing at ends.

Supply laying and testing cable XLPE insulated Screened PVC bedded galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded alum conductor of size 10 sqmmm 2 core

All as per item No. 129.00 above but 16 sqmm 4 core

M& L for Earthing complete with galvanized steel earth plate electrode of size 60cm X 60 cm X 6 mm buried directly in ground (earth pit not less than 2.25m deep below the normal ground level) with top edge of plate not less than 1.5 m below the normal ground level connected to GI earth strip 32 X 6 mm dia GI earth lead as earth lead by means of bolts, nuts, check nuts and washers of galvanized iron or steel, protected by GI pipe light grade 40mm bore all as shown on electrical plate No 3 of SSR Part-I connected to earth test point electrode, PCC pit with RCC cover, funnel with wire mesh, watering pipe 20mm dia protection pipe etc and testing on completion complete all as specified and directed. Note No 1 :- The unit rate shall also include for earth work in hard/dense soil, PCC (1:3:6) type C1 chamber, RCC 1:2:4 type B-1 cover 50 mm thick reinforced with 8 mm dia TMT bar @ 150 mm c/c both ways, funnel with watering pipe 20 mm dia medium grade, GI protection pipe light grade 40 mm dia and wire mesh complete in addition to item No 1 (a) to (e) of preamble (Notes) under sub-heading earthing, specified on Serial Page No 389 of SSR Part –I. Note No 2 :- Earth strip and GI protection pipe beyond 7.5 m will be measured and paid separately if required.

M&L for run lead joint for spigot and socketed end CI pipe & fittings complete all as specified incl excavation, returning & refilling and directed by Engr in charge for following :-

(a) 100 mm bore

(b) 150 mm bore

(c) 250 mm bore

M & L for Construction of Valve pit brick/stone/PCC block masonry constructed complete with Mild steel sheet cover 3mm thick and angle iron frame of size 40x40x6mm duly painted with two coats of synthetic enamel paint over a coat of red oxide primer and including locking arrangement and lifting handle all as specified and shown on drawing . Brick/stone/PCC block work all inner surfaces of pit shall be plastered in cement mortar 1:4 complete all as specified and directed.

Internal size 900mm x 900mm x 900mm

Internal size 1200mm x 1200mm x 1200mm

Supply, Installation, Testing and Commissioning of 50 mm dia, single phase, Motor Actuated Butterfly valve with disc material of CI with nylon coating, hand wheel for manual operation and having 02 nos. limit switches for Open / Close condition, valve position indicator. In built Serial / USB communication Port, In built data logger with memory, In built SD Card. The mounting shall be indirect type using specialized extended type arrangement of GI pipe / plate of suitable size/thickness, angle irons and indirect mounting adaptors including raising of existing chamber if required so that actuator mounting is at least 12 inches above ground level complete all as specified and directed.- Make: RITE TORK / HASEL HOFENER / EMTORK

Blank

M&L for cement concrete ( 1:4:8) type D2 using 40mm graded stone aggregate for foundation filling of poles as mass concrete complete all as specified and directed .

ITEM FOR PHASE 2 WORK : (Total 2 Nos Shift per day) AMC/ Outsourcing the resources for monitoring, management and operation of water managment control system i.e. up to 330 days from actual date of completion of Phase I. It includes providing the follwing manpower (1) 1 trained technician ITI qualified (trade as per requirment of Engr-in-charge) for Master Control Station and helper for attending/monitoring the breakdown and preventive maintenance in the general shift. and 1 company (OEM of PLC based Panels & Motorised Valves) trained technician for Master Control Station for attending/monitoring the breakdown and preventive maintenance in the first / last shift.The trained techician shall possess a certificate from the PLC based Panel manufacturer clearly stating the he / she has been trained in a) Trouble shooting, repairs and maintenance of PLC based Panels, b) Establishing communication between the PLC based Panels and the SCADA Control center, c) Uploading and downloading of ladder logic based programs and d) Manual / Remote operation from the PLC based Panel / SCADA software (2) Tools and Machinery,

Ser item No 137.00 continued : The technician and the helper shall carry out the below described preventive maintenance and maintain proper log sheets of the works carried out; a. Servicing of all Motorised valves once every quarter (three monhs) including cleaning,greasing,checking for wear and tear, checking electrical termination etc all as required b. Cleaning all PLC based Panels once every five / six months including checking electrical termination etc. as required. c. Servicing of all Pressure switches and solenoid valves once every six months including cleaning,greasing,checking for wear and tear, checking electrical termination etc all as required. The technician shall submit reports in soft / hard copy format as required by the Engineer in Charge. d. All cost of GPRS based communcation, wired broad band charge for the period is included in one amount quated for Phase -I.

ITEM FOR PHASE 3 WORK : (Total 2 Nos Shift per day) AMC/ Outsourcing the resources for monitoring, management and operation of water managment control system i.e. up to 330 days from actual date of completion of Phase II. It includes providing the following manpower (1) 1 trained technician ITI qualified (trade as per requirment of Engr-in-charge) for Master Control Station and helper for attending/monitoring the breakdown and preventive maintenance in the general shift. and 1 company (OEM of PLC based Panels & Motorised Valves) trained technician for Master Control Station for attending/monitoring the breakdown and preventive maintenance in the first / last shift.The trained technician shall possess a certificate from the PLC based Panel manufacturer clearly stating the he / she has been trained in a) Trouble shooting, repairs and maintenance of PLC based Panels, b) Establishing communication between the PLC based Panels and the SCADA Control center, c) Uploading and downloading of ladder logic based programs and d) Manual / Remote operation from the PLC based Panel / SCADA software (2) Tools and Machinery, (3) All spares required for smooth and efficient working of the system.

Ser item No 138.00 continued : The technician and the helper shall carry out the below described preventive maintenance and maintain proper log sheets of the works carried out; a. Servicing of all Motorised valves once every quarter (three monhs) including cleaning,greasing,checking for wear and tear, checking electrical termination etc all as required b. Cleaning all PLC based Panels once every five / six months including checking electrical termination etc. as required. c. Servicing of all Pressure switches and solenoid valves once every six months including cleaning,greasing,checking for wear and tear, checking electrical termination etc all as required. The technician shall submit reports in soft / hard copy format as required by the Engineer in Charge. d. All cost of GPRS based communcation, wired broad band charge for the period is included in one amount quated for Phase -I.

ITEM FOR PHASE 4 WORK : (Total 2 Nos Shift per day) AMC/ Outsourcing the resources for monitoring, management and operation of water managment control system i.e. up to 330 days from actual date of completion of Phase III. It includes providing the following manpower (1) 1 trained technician ITI qualified (trade as per requirment of Engr-in-charge) for Master Control Station and helper for attending/monitoring the breakdown and preventive maintenance in the general shift. and 1 company (OEM of PLC based Panels & Motorised Valves) trained technician for Master Control Station for attending/monitoring the breakdown and preventive maintenance in the first / last shift.The trained technician shall possess a certificate from the PLC based Panel manufacturer clearly stating the he / she has been trained in a) Trouble shooting, repairs and maintenance of PLC based Panels, b) Establishing communication between the PLC based Panels and the SCADA Control center, c) Uploading and downloading of ladder logic based programs and d) Manual / Remote operation from the PLC based Panel / SCADA software (2) Tools and Machinery, (3) All spares required for smooth and efficient working of the system.

Ser item No 139.00 continued : The technician and the helper shall carry out the below described preventive maintenance and maintain proper log sheets of the works carried out; a. Servicing of all Motorised valves once every quarter (three monhs) including cleaning,greasing,checking for wear and tear, checking electrical termination etc all as required b. Cleaning all PLC based Panels once every five / six months including checking electrical termination etc. as required. c. Servicing of all Pressure switches and solenoid valves once every six months including cleaning,greasing,checking for wear and tear, checking electrical termination etc all as required. The technician shall submit reports in soft / hard copy format as required by the Engineer in Charge. d. All cost of GPRS based communcation, wired broad band charge for the period is included in one amount quated for Phase -I.

M/s JAIMAA ASSOCIATES

m/s jethanand bhatia

Jyoti enterprises

M/S JAI BHAWANI CONSTRUCTIONS

Mata Builders