IRSHUP/RED/02/Rebid-2

Amount

Earth work excavation for foundation with all initial leads and lifts in all soils and sub soils and to the required depth as may be directed except hard rock requiring blasting inclusive of shoring, strutting and bailing out water wherever necessary refilling the sides of foundation with excavated earth in layers of not exceeding 15cm thick well consolidated depositing the surplus earth in places shown and levelling the site with all leads and lifts etc.,complete in all respects as directed by the Engineer or his representative.

Earth work excavation for foundation with all initial leads and lifts in all soils and sub soils and to the required depth as may be directed except hard rock requiring blasting inclusive of shoring, strutting and bailing out water wherever necessary refilling the sides of foundation with excavated earth in layers of not exceeding 15cm thick well consolidated depositing the surplus earth in places shown and levelling the site with all leads and lifts etc.,complete in all respects as directed by the Engineer or his representative. (For additional lift of 1m (depth from 2m to 3m)

Filling in foundation and basement with M-sand in layers of not exceeding 15cm thick well watered, rammed and consolidated complying with relevant standard specification including the cost of supplying M- sand etc., complete in all respects as directed by the Engineer or his representative.

Filling in foundation and basement with quarry dust in layers of not exceeding 15cm thick well watered, rammed and consolidated complying with relevant standard specification including the cost of supplying quarry dust etc., complete in all respects as directed by the Engineer or his representative

Cement Concrete 1:4:8 (one of cement, four of M-sand and eight of hard broken stone) using 20mm size hard broken stone for foundation inclusive of shoring, strutting, bailing out water, ramming, curing etc., complete in all respects as directed by the Engineer or his representative.

Supply of Ready Mix Concrete M-30 Grade in accordance with IS:456-2000, using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 400 kg/m3 and maximum water cement ratio of 0.45, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability withability without impairing strength and durability with about (5.0 cu.m.) 7730 kg of 20mm machine crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu.m') 7670 kg. of M-Sand, but excluding cost of reinforcement and fabrication charges, centering and shuttering, mix details to get approved before commencement of the work adopting pour card system as per IS 456 / 2000 etc., complete in all respects as directed by the Engineer or his representative. (All floors)

Providing form work for centering, shuttering etc., for all reinforced concrete work as plinth beam raft beam, raft slab, grade beam etc., including shuttering upto 3.0M high using M.S. sheet of size 90cm x 60cm and BG 10, stiffened with alround M.S. angle of size 25mm x 25mm x 3mm laid over Silver Oak (Country wood) joists of size 10cm x 6.5cm (spaced about 91 cm centre to centre) distance and supported by casurina props of size 10cm to 13cm dia (spaced at 75 cm centre to centre ) and removing the same after a specified period without damaging the RCC works in all floors etc., complete as directed by the Engineer or his representative

Providing form work for centering, shuttering etc., for plane surface of all reinforced concrete work such as slab, beams, lintelts, loft etc., including shuttering upto 3.0M high using M.S. sheet of size 90cm x 60cm and BG 10 stiffened with alround M.S. angle of size 25mm x 25mm x 3mm laid over Silver Oak (Country wood) joists of size 10cm x 6.5cm (spaced about 91 cm centre to centre) distance and supported by casurina props of size 10cm to 13 cm dia (spaced at 75 cm centre to centre ) and removing the same after a specified period without damaging the RCC works in all floors etc., complete as directed by the Engineer or his representative

Providing form work for centering, shuttering etc., for all RCC works like column, windows boxing, sunshade etc including shuttering upto 3.0M high using M.S. sheet of size 90cm x 60cm and BG 10 stiffened with alround M.S. angle of size 25mm x 25mm x 3mm laid over Silver Oak (country wood) joists of size 10cm x 6.5cm (spaced about 91 cm centre to centre ) distance and supported by casurina props of size 10cm to 13 cm dia (spaced about 75 cm centre to centre ) and removing the same after a specified period without damaging the RCC works in all floors etc., complete as directed by the Engineer or his representative.

Fabricating and placing the following kinds of steel grills Fe 500D grade steel reinforcement bars asper IS 786-1979 for all reinforced cement concrete works such as plinth beam, lintels, beams, sundhades, roof and floor slab etc., including cost of steel, binding wire and labour charges for fabricating the reinforcement in position etc., complete in all respects as directed by the Engineer or his representative. (The rate includes the cost of binding wire also) Steel Rods of All sizes.

Brick work in cement mortar 1:5 (one of cement and five of M-sand) using Fly Ash bricks of minimum size 23cm X 11cm X 7cm including dewatering wherever necessary, proper setting and curing etc., complete in all respects as directed by the Engineer or his representative. In Foundation and Basement.

Brick work in cement mortar 1:6 (one of cement and six of M-sand) using Fly Ash bricks of minimum size 23cm X 11cm X 7cm in super structure including fixing the frames of doors and windows, scaffolding, proper setting, curing etc., complete in all respects as directed by the Engineer or his representative.

Ground Floor

First Floor

Second Floor

Third Floor

Terrace

Brick partition wall 11cm thick in cement mortar 1:5 (one of cement and five of M-sand) using Fly Ash bricks of minimum size 23cm X11cm X7cm in super structure including fixing the frames of doors and windows, scaffolding, proper setting, curing etc., complete in all respects as directed by the Engineer or his representative.

Ground Floor

First Floor

Second Floor

Third Floor

Brick partition wall 7cm thick in cement mortar 1:5 (one of cement and five of M-sand) using Fly Ash bricks of minimum size 230mm X 110mm X70mm in super structure including fixing the frames of doors and windows, scaffolding, proper setting, curing etc., complete in all respects as directed by the Engineer or his representative.

Ground Floor

First Floor

Second Floor

Third Floor

Average rate of all floors for elevation

Plastering with cement mortar 1:5 (one of cement and five of P-sand) 12 mm thick including providing band cornice, scaffolding, finishing smooth, setting, curing etc., complete in all respects as directed by the Engineer or his representative.

Special ceiling plastering for all RCC works in cement mortar 1:3 (one of cement and three of P-sand) 10 mm including hacking the RCC surface, providing necessary water band using the same mix of mortor wherever necessary proper finishing, curing, scaffolding etc., complete in all respects as directed by the Engineer or his representative.

Plastering with cement mortar 1:3 (one of cement and three of P-sand) 12 mm thick with water proofing compound including providing band cornice, scaffolding, finishing smooth, setting, curing etc., complete in all respects as directed by the Engineer or his representative.

Providing 7cm thick staircase parapet wall in cement mortar 1:4 (one of cement and four of M-sand) using fly ash bricks of minimum size 230mm X 110mm X70mm and plastering the hand rail portion only with red oxide plastering in cement mortar 1:4 (one of cement and four of M-sand) 20 mm thick using 9.80 kg of red oxide powder per 10 m² and plastering the side with cement mortar 1:4 (one of cement and four of P-sand) 20 mm thick including providing skirting, proper setting, curing, finishing smooth in all floors etc., complete in all respects as directed by the Engineer or his representative. In all floors.

Cement concrete 1:5:12.5 (One of cement, five of M-sand and twelve and half of broken brick jelly) using 20mm size broken brick jelly including laying, ramming, curing finishing, etc. complete in all respects as directed by the Engineer or his representative.

Finishing the top of roof with reflected ceramic cooling tiles of size 305mmx305mmx6mm of approved brand and quality in cement mortar 1:3(one of cement and three of M-sand) 12mm thick mixed with water proofing compound 2% by weight of cement used and pointing with same mortar etc., complete in all respects as directed by the Engineer or his representative.

White washing two coats of clean shell lime including cost of lime, gum, brushes, scaffolding etc., complete in all respects as directed by the Engineer or his representative.

Wall putty Two coats over new plastered surface including preparation of surface ,cost of wall putty and putty plates, brushes, scaffolding and labour charges etc., complete in all respects as directed by the Engineer or his representative.

Painting two coats of newly plastered wall surface with ready mixed exterior/Interior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt and including necessary plaster of Paris putty, wherever required etc., complete in all respects as directed by the Engineer or his representative.

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60mm x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Engineer or his representative before use on work. (All floors)

Supplying and fixing of Door frame for the following over all size with required dimensions of size~ 100 mm x 75 mm, with groove of size ~ 30 mm x 20 mm for resting the door shutter & chamfer finish at front using CRCA pressed steel box section 18 gauge or 1.25mm thick for door frames including providing holes and fixing wooden blocks for fixing fixtures and fittings and 4 nos of hold fast using the iron angle of 15cm length with split ends one coat of redoxide primer/ chemical arcylic Fabrication and Supply of 35mm thick solid core flush door with teakply on one side and commercial ply on other side with teak wood liping alround with iron oxidised hinges,tower bolts 12" 2 nos with receiver,Aldrop 30 cm and handle 1 no complete in all respects as directed by the Engineer or his representative.

Supplying and fixing of factory made PVC rigid panel door with frame made from MS tubes of 19 gauge size of 19mm x 19mm and covered with heat moulded PVC channel of 5mm thick and width of 50mm to form styles and rails. The inner panel should be inserted between the frame with 6mm thick PVC rigid foam sheet welded/sealed to the styles and rails along with 5mmx25mm PVC beading on all and either sides. The vertical tube may be filled with suitable materials to further enhance the screw holding capacity etc., complete in all respects as directed by the Engineer or his representative. Door Size 0.76m x 1.98 m

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Engineer or his representative before use on work

Supplying and fixing in position of cuddapah slab planks of various sizes 20mm thick both sides polished for cup-board planks of required size including cost of slab, labour charges for cutting and fixing in position, finishing curing etc., complete in all respects as directed by the Engineer or his representative.

Plastering the top of flooring with cement morter 1:4, (One of cement and four of P-Sand) 20mm thick including finishing smooth, scaffolding, setting, curing etc., complete in all respects as directed by the Engineer or his representatives

Providing Ellis pattern flooring, 20mm thick with layer of cement concrete 1:3 (one of cement and three of hard broken stone jelly) (no M-sand) using hard broken granite stone chips of size 3mm to 10mm and the surface rendered smooth over RCC slab including supplying and fixing 20mm dia GI pipe outlet etc., complete in all respects as directed by the Engineer or his representative.

Paving the flooring with best quality stainfree nano polish vitrified tiles of minimum size 600mmx600mmx8mm of approved colour, shape and quality laid in cement mortar 1:3 (one of cement and three of M-sand), 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete as directed by the Engineer or his representative. ( The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Painting the new iron work with one coat ready mixed synthetic enamel paint (First Class) of approved quality and colour including cost of paint, brushes, scaffolding etc., complete in all respects as directed by the Engineer or his representative.

Painting the new wood works two coats with ready mixed synthetic enamel paint (Ist class) of approved quality and colour over coat of priming with approved primer including cost of paint brushes and scaffolding etc., complete in all respects as directed by the Engineer or his representative.

Flooring with ceramic tiles of approved quality, color and design anti skid type joint free of minimum size 305mmX305mmX6mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3 (one of cement and three of M-sand), 20mm thick laid straight alignment and pointed neatly with colour cement @ 0.40kg/M2 laid without any air gap in the tiles neatly and fixing in position as per the standard specification complete as directed by the Engineer or his representative.

Dadooing the walls with first quality colour glazed tiles of of approved quality with minimum size 150mmX150mmX6mm laid in cement mortar 1:2 (one of cement and two of M-sand), 10mm thick and pointing with white cement using 0.40 kg / M2 including finishing the joint and pointing flash with tiles surface etc., complete as directed by the Engineer or his representative.

Supplying and fixing in position White / Colour Glazed Model Floor Mounted European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelain low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications. (The EWC and flushing tank with all accessories should be got approved by the Engineer or his representative before use on works) Floor Fitting for all floor

Supplying and fixing of 110mm dia UPVC SWR pipe 4kg / cm2 Type- A confirming to IS13592 with 1 No of UPVC bend/elbow and 1 No of shoe with necessary clamps couplers gratings, teak wood plug etc. complete including fixing in proper position with solvent cement, making holes in the walls good of the dismantled portion with necessary brick work in CM etc in all respects ad directed by the departmental offices by the Engineer or his representative

Supplying and fixing of UPVC SWR pipe of 6 kg/cm2 of approved quality confirming to IS 13592/1992 (Type-B) of finolex (or) equivalent with ISI monogram packing the joints with including fixing into walls with necessary connection to the sanitary fittings testing etc complete in all repsects in all floors as directed as directed by the Engineer or his representative.

110mm Dia of pipe 6kg/cm2 (Vertical Line)

75mm Dia of pipe 6kg/cm2 (Vertical Line)

Supplying and fixing of UPVC SWR pipe of 6 kg/cm2 of approved quality confirming to IS 13592/1992 (Type-B) of finolex (or) equivalent with ISI monogram packing the joints with including fixing into water closet room and bathroom with necessary connection to the sanitary fittings testing etc complete in all repsects in all floors as directed as directed by the Engineer or his representative.

110mm Dia of pipe 6kg/cm2 (Horizontal Line)

75mm Dia of pipe 6kg/cm2 (Horizontal Line)

Supplying and fixing the following UPVC specials of approved quality etc., complete in all respects as directed by the Engineer or his representative.

110mm dia cowl

75mm dia cowl

110mm dia single Tee with door

75mm dia single Tee with door

110mm shoe

75mm shoe

110mm dia elbow for rain water

Supplying and fixing of 100mm x 75 mm PVC Nahini Trap with grating 4way/2way (superior quality) having minimum seal of 50mm conforming to relevant IS specifications with its latest amendments including resting at the bed of brick jelly concrete 1:5:12½ (One of cement, five of sand and twelve and half broken brick jelly) using 40 mm size broken brick jelly etc., complete in all respects as directed by the Engineer or his representative.

Supplying, laying and jointing UPVC pipes of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, SS clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The UPVC pipes shall be got approved by Executive Engineer before use on works as per IS 4985 tc., complete in all respects as directed by the Engineer or his representative.

20mm dia UPVC Pipe

25mm dia UPVC Pipe

32mm dia UPVC pipe

40mm dia UPVC pipe

Supplying of UPVC pipe specials of approved quality suitable to pipe as per table II IS 13593 at site of work etc., complete in all respects as directed by the Engineer or his representative.

32mm dia Elbow

32mm × 25mm size Reducer

25mm dia Coupler

20mm dia Tee

20mm dia Elbow

20mm dia Coupler

20mm x 15mm size Female Reducer

15mm Dia Screw Down Tap (Heavy)

25 mm dia FTA

20mm dia FTA

40mm dia Elbow

40mm dia Coupler

Supply of GI pipes and ISS 1239 (Medium) screwed at both ends and complete in all respects as directed by the departmental officers Engineer or his representative.

32mm dia GI pipe

Labour charges for cutting and joininting the GI rigid pipes using solvent cement required with necessary specials of the follwing dia above ground level including fixing to wall with necessary teak wood plugs, clamps and screws making holes in the wall or drilling holes in the roof making packed the same with necessary brick work and plastering wherever necessary painting etc with necessary scaffolding etc complete in all respects as directed by the Engineer or his representative.

32mm dia GI pipe

Supplying of GI and GM specials confirming to ISI etc., complete in all respects as directed by the Engineer or his representative.

32mm dia GI Elbow

40mm x32 mm dia GI Reducer

25mm GM Wheel Valve

32mm GM Gate Valve

40mm dia GI union / Coupler

Construction of inspection chamber of size 0.60M X 0.60M for the following depth with brick jelly cement concrete 1:5:12½ (one of cement, five of M-sand and twelve and half of broken brick jelly) using 40mm size broken brick jelly, 15cm thick for foundation, 23 cm thick masonry walls in cement mortar 1:5 (one of cement and five of M-sand) using IInd class ground moulded chamber burnt bricks of size 9"×4⅜"×2¾" and inside plastering with cement mortar 1:3 (one of cement and three of P-sand) 12mm thick including channeling, benching etc., and top covered with SFRC cover slab (medium duty) and curing with necessary earthwork excavation for foundation, refilling the sides of foundation in all soils except hard rock requiring blasting 0.60M depth requiring blasting etc., as directed by the Engineer or his representative. 0.60M depth (average)

Construction of Gully chamber 0.23 x 0.23 m x 0.3 m depth with brick masonry wall of 12 cm thick cement concrete 1:5 :12.5 (one of cement, five of M-sand and twelve and half of broken stone jelly ) using 40mm HBSJ of 10cm thick for foundation including channeling benching etc and plastering the inside with 1:3 ( One of cement and 3 of sand) 12 mm thick with gully trap of size 150mm x 100mm including casting and fixing in position and necessary earth work excavation, refilling the sides of foundation in all soils except hard rock requiring blasting etc., complete in all respects as directed by the Engineer or his representative.

Providing iron grills for closing the opening using square rods as including one coat of red oxide primer cutting, welding, labour for fxing etc., complete in all respects as directed by the Engineer or his representative.

Supplying and fixing Stainless steel sink of size 600mmX450mmX200mm including labour, drilling into the wall, plastering the drill holes etc., complete in all respects as directed by the Engineer or his representative.

Wiring with 2x1.5sqmm PVC insulated single coreunsheathed copper condutor cable of 1100 V gradewith ISI mark confirming to IS:694/1990 in suitable PVC rigid pipe of 1.8mm thick with ISI mark concealed in wall and ceiling with PVC accessories in flushwith wall including the cost of cable, PVC pipe and specials, ceiling rose, flush type 5ams SP mark switch, PVC junction box, 16 gauge MS switch box 100mm x 100mm x 75mm covered by laminated hylem sheet 3mm thick, cement, labour and makingood of concealed portion with suitable colour forconcealed Light point etc., complete in all respects as directed by the Engineer or his representative.

Without Ceiling Rose / With Bakelite holder

With Ceiling Rose

Wiring with 2x1.5sqmm PVC insulated single coreunsheathed copper conducter cable of 1100V grade with ISI mark confirming to IS:694/1990 in suitable PVC rigid pipe of 1.8mm thick with ISI mark concealed in wall and ceiling with PVC accessories in flush with wall including the cost of cable, pvc pipe and specials, ceiling rose, flush type 5Ams SP mark switch, PVC junction box, 16gauge MS switch box 300mm x 200mm x 75mm covered by laminated hylem sheet3mm thick, cement, labour and making good of concealed portion with suitable colour for concealed FAN Point etc., complete in all respects as directed by the Engineer or his representative.

Supplying and run off 2 of 2.50 sq.mm PVC insulated single core unsheathed copper conductor cable of 1100V grade with ISI mark confirming to IS:694/1990 with continuous earh connection by means of 1.50 sqmm PVC insulated single core unsheathed copper condctor cable confirming to IS:694/1990 in suitable PVC rigid pipe 1.8mm thick concealed on walls and ceiling for mains including the cost of cable, PVC pipes and specials, cement, brass screws, TW plugs, saddless and labour tc., complete in all respects as directed by the Engineer or his representative.

Supplying and fixing of 5 Amps /15Amps 3 pin flush type wall socket with15A flush type switch concealed in suitable MS box in flush with wall and covered with 3mm thick hylem sheet including cost of wall socket, switch and labour charges for wall cutting, grouting, flushing and making good, painting with primary and finishing coat for MS box etc., complete in all respects as directed by the Engineer or his representative.

Supplying and fixing of 5 Amps 3 pin and 2 pin combined flush type wall socket with 5Amps flush type switch concealed in suitable MS box in flush with wall and covered with 3mm thick hylem sheet including cost of wall socket, switch and labour charges etc., complete in all respects as directed by the Engineer or his representative.

Supplying and run off 8 SWG copper wire on walls or below ground level with necessary 'U' nails, earthwork excavation and refilling inclusive of the cost of all materials etc., complete in all respects as directed by the Engineer or his representative.

Supply and insallation maintenance free GI Earthing System comprising of 50mm dia and 2 mtr. long earth electrode of low carbon steel rod with 100 micron bonding and 25 kgs. of carbon based environment friendly backfill compound and suitable clamp etc., complete in all respects as directed by the Engineer or his representative.

Supplying and fixing single phase 4 way Distribution Board flush type vertical SPMCB sheet steel fitted with bus bars and neutral links with single phase MCB out goings and separate 2 way provision for accommodating one no 2 pole incoming MCB and another separate 2 way provision for accommodating one no 2 pole ELCB with label holder and provision for taking up cable etc., complete in all respects as directed by the Engineer or his representative.

Supplying and fixing of water tight bulk head fitting (heavy type) with guards suitable for 100/60 watts bulb including the cost of bulb, necessary connection cost of mateials etc., complete in all respects as directed by the Engineer or his representative.

Wiring with 2x4 sq.mm (56/0.3) PVC insulated SC unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, with 150mmx100mmx113mm TW switch box with 3mm thick hylem sheet for 15A 3 pin non interlocking CS plug with continuous earth wire connection with 1.5sq.mm PVC unsheathed copper cable and making good of the concealed portion, with suitable colour for concealed PVC plug point.(hall & kitchen- each one) complete in all respects as directed by the Engineer or his representative.

Supply and erection of 125 Amps capacity floor Mounting type metering Panel Board

Supply and erection of 125 Amps capacity floor Mounting type metering Panel Board of required size 250mm (cubical type) with bus bar chamber made up of 16 gauge CRCA sheet fully powdered coated for 3 phase 4 wire system with 40mm x 10mm aluminium bar for phases and neutral cable chamber, switch chamber and with 2nos 25mm x3mm aluminium flat for the earth bus on the rear side of the panel board; suitable PVC colour sleeves for the inter connecting flays / rigid copper wire; earth connections to all switches /bus bar by aluminium flats of suitable sizes from the earth bus; suitable angle iron frame of size of 40mm x 40mm x 6mm with powder coated painting over one coat of red oxide and incorporating the following incoming 1 no 100 Amps TPN SDF with HRC fuse links for incoming 32 Amps DP MCB switches 40 nos, 32Amps fuse unit, 2 nos 25mmx 3mm aluminium flats for neutral and earth for outgoings upto earth GI pipe, space provision for TNEB, Energy meter, 1 no of dummy provision all complete internal connection by 3 runs of 4 sq.mm PVC insulator unsheathed copper conductor of 1100 V grade from TNEB the 32Amps DP circuit to the meter and from the meter to MC switch 1set LED pilot lamps with fuse units, switches and inter connection to the bus bar by 25mm x 3mm aluminium flats for phase and neutral from 100Amps TPN SDF to the bus; inter connection by 8 SWG copper for the phases and 32Amps DP circuit to the meter and from the meter to MC switch and 1 set LED pilot lamps bus; 6mm thick hylem sheet separation between bus bar chamber and switches chamber; insulators for the support for the bus ; super scribing on the panel board of the size capacity of cables, switches, location etc., 2nos of metallic danger boards etc., complete in all respects as directed by the Engineer or his representative. for 32 in 1 block

Supply and erection of 125 Amps capacity floor Mounting type metering Panel Board of required size 250mm (cubical type) with bus bar chamber made up of 16 gauge CRCA sheet fully powdered coated for 3 phase 4 wire system with 40mm x 10mm aluminium bar for phases and neutral cable chamber, switch chamber and with 2nos 25mm x3mm aluminium flat for the earth bus on the rear side of the panel board; suitable PVC colour sleeves for the inter connecting flays / rigid copper wire; earth connections to all switches /bus bar by aluminium flats of suitable sizes from the earth bus; suitable angle iron frame of size of 40mm x 40mm x 6mm with powder coated painting over one coat of red oxide and incorporating the following incoming 1 no 100 Amps TPN SDF with HRC fuse links for incoming 32 Amps DP MCB switches 40 nos, 32Amps fuse unit, 2 nos 25mmx 3mm aluminium flats for neutral and earth for outgoings upto earth GI pipe, space provision for TNEB, Energy meter, 1 no of dummy provision all complete internal connection by 3 runs of 4 sq.mm PVC insulator unsheathed copper conductor of 1100 V grade from TNEB the 32Amps DP circuit to the meter and from the meter to MC switch 1set LED pilot lamps with fuse units, switches and inter connection to the bus bar by 25mm x 3mm aluiminium flats for phase and neutral from 100Amps TPN SDF to the bus; inter connection by 8 SWG copper for the phases and 32Amps DP circuit to the meter and from the meter to MC switch and 1 set LED pilot lamps bus; 6mm thick hylem sheet separation between bus bar chamber and switches chamber; insulators for the support for the bus ; super scribing on the panel board of the size capacity of cables, switches, location etc., 2nos of metallic danger boards tec., complete in all respects as directed by the Engineer or his representative. 28 in 1 block

Supply and erection of 125 Amps capacity floor Mounting type metering Panel Board of required size 250mm (cubical type) with bus bar chamber made up of 16 gauge CRCA sheet fully powdered coated for 3 phase 4 wire system with 40mm x 10mm aluminium bar for phases and neutral cable chamber, switch chamber and with 2nos 25mm x3mm aluminium flat for the earth bus on the rear side of the panel board; suitable PVC colour sleeves for the inter connecting flays / rigid copper wire; earth connections to all switches /bus bar by aluminium flats of suitable sizes from the earth bus; suitable angle iron frame of size of 40mm x 40mm x 6mm with powder coated painting over one coat of red oxide and incorporating the following incoming 1 no 100 Amps TPN SDF with HRC fuse links for incoming 32 Amps DP MCB switches 40 nos, 32Amps fuse unit, 2 nos 25mmx 3mm aluminium flats for neutral and earth for outgoings upto earth GI pipe, space provision for TNEB, Energy meter, 1 no of dummy provision all complete internal connection by 3 runs of 4 sq.mm PVC insulator unsheathed copper conductor of 1100 V grade from TNEB the 32Amps DP circuit to the meter and from the meter to MC switch 1set LED pilot lamps with fuse units, switches and inter connection to the bus bar by 25mm x 3mm aluiminium flats for phase and neutral from 100Amps TPN SDF to the bus; inter connection by 8 SWG copper for the phases and 32Amps DP circuit to the meter and from the meter to MC switch and 1 set LED pilot lamps bus; 6mm thick hylem sheet separation between bus bar chamber and switches chamber; insulators for the support for the bus ; super scribing on the panel board of the size capacity of cables, switches, location etc., 2nos of metallic danger boards tec., complete in all respects as directed by the Engineer or his representative. for 30 in 1 block

Supplying and laying of 3-½ x 70 sq.mm PVC armoured aluminium LT UG cable of approved brand having ISI mark in a trench to be excavated to a depth of 0.75 meter, putting 0.15 m layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good etc., complete in all respects as directed by the Engineer or his representative. (Below G.L) from panel board to EB pole

Supplying and laying of 3- ½ x 70 sq.mm PVC armoured aluminium LT UG cable of approved brand having ISI mark on post or wall with MS clamps etc., complete in all respects as directed by the Engineer or his representative. On EB pole

Supply and fixing of 50mm dia GI pipe of approved quality and ISS 1239 (Medium) screwed at both ends and complete in all respects as directed by the departmental officers Engineer or his representative.

Supplying and fixing of 3 nos of 100Amps porcelain fuse units 500 volt of approved brand having ISI mark in TW board of suitable size etc., complete in all respects as directed by the Engineer or his representative.

Supplying and fixing brass cable gland for 3 ½ x 70 sq.mm PVC armoured LT UG cable with earth connection etc., complete in all respects as directed by the Engineer or his representative.

Supplying and fixing cable end termination for 3 ½ x 70 sq.mm PVC armoured LT UG cable with earth connection etc., complete in all respects as directed by the Engineer or his representative.

Supplying and fixing in position best quality approved make white glazed earthenware wash hand basin of size 550mm x 400mm with a pair of cast iron brackets, including cost of 15mm dia brass chromium plated pillar tap, 32mm dia C.P waste coupling, 32mm dia "B" G.I waste pipe, 15mm dia G.M wheel valve, 15mm dia pillar tap etc., nylon connection 15mm dia brass nipples, 15mm C.P etc., complete in all respects as directed by the Engineer or his representative.

Providing expansion joint in RCC floor slab for 12.5mm width using polysulphide as sealant on the top and bottom for a depth of 7.5mm each and packing the inner space using compressible non-absorbent filler materials including cost of labour for cutting and fixing filler materials and laying polysulphide sealant with necessary spatula etc., complete complying with standard specifications and as directed by the Engineer or his representative.

Providing expansion joint 12.5mm width in RCC roof slabs between RCC twin beams using PVC water bar of 150mm wide centre bulb of 4mm to 6mm thickness of approved quality and brand and including filling the inner space with suitable non-absorbent flexible and well compressible filler materials of approved quality and covering the top surface with GI sheet 30cm wide and 1.6mm thick using phil plugs, GI screws, limpet cup washers, bitumen washers, etc., complete complying with standard specifications and as directed by the Engineer or his representative.

Providing expansion joint of 12.5mm wide in between RCC twin columns from top of pedestal to full height including filling the inner space with suitable non-absorbent, flexible and well compressible filler materials of approved quality and brand; finishing the sides of RCC columns with polysulphide sealants for a depth of 7.5mm on either side covering the inner space filled with filler materials as above etc., complete complying with standard specifications and as directed by the Engineer or his representative.

Painting the wall with Texture finish paint including labour charges etc., complete in all respects as directed by the Engineer or his representative.

Supply and fixing the shera wooden planks of 8mm thick with necessary bolt & nuts and other arrangements including labour charges for fixing in position etc., complete in all respects as directed by the Engineer or his representative.

Providing horizontal grooves of size 25mmX6mm at regular intervals Plasteredsurface alround the building as directed by the Engineer including proper finishingcuring etc., complete in all respects as directed by the Engineer or his representative.

Sectioning the site including cutting the undulations and filling upto 15cm thick and levelling etc., complete in all respects as directed by the Engineer or his representative.

Providing and laying sand gravel mix 1:1 (one of sand and one of gravel) to the 150 mm thickness to be laid two layers to give a minimum soaked CBR value as per IRC 37-1984 including cost and conveyance of sand and gravel to the work site and stacking them to the standard departmental metric guage ,labour charges for mixing the required quantities of sand and gravel spreading,watering and compacting the mix in layers of thickness not exceeding 10mm compacted thickness by 80-100KN power roller rolling to achive the required proctor density including the labuor charges for mixing spreading and all other tools and plants and other incidential charges., etc., complete in all respects as directed by the Engineer or his representative.

Providing and laying Water Bound Macadam for 75mm consolidated thickness with Grade II metal confirming MOST specification using 0.41m3 of 63mm, 39 m3 of 53mm and 0.2m3 of 45mm IRC metal with 0.24m3 of gravel for blind age for 10 sqm including the cost and conveyance of material from approved quarry to road site and stacking them to the departmental gauge for pre-measurement, labour charges for spreading in layers, hand packing to camber, dry rolling, watering, blind age including cost and conveyance for good water, forming edge bunds, slurrying and consolidation by power roller hire, running slurrying and fuel charges for power roller, water sprinkler and other tools and plants employed for the work including all other incidental charges such as barricading and providing danger lights etc., complete in all respects as directed by the Engineer or his representative as per standard specification.

Providing and laying Water Bound Macadam for 75mm consolidated thickness with grade III metal confirming MOST specification using 0.36 of 53 mm, 0.35 cum of 45mm and 0.29 cum of 26.5mm IRC size HBG metal with 0.24 cum of gravel as screening whose P.I. Value is less than 6 for blind age for 10 sqm including cost and conveyance of material the departmental gauge for pre-measurement labour to camber, dry rolling, watering, blind age including cost and conveyance for good water, forming edge bunds, slurrying and consolidation by power roller to achieve the specified compaction including all labour water sprinkler and other tools and plants employed for the work including all other incidental charges such as barricading and providing danger lights etc., complete in all respects as directed by the Engineer or his representative.

Applying tack coat over un primed WBM surface using 4kg of bitumen Emulsion for 10m2 including cost of bitumen conveyance to site handing charges including labour charges for brushing, cleaning and preparing the surface for laying the coat and labour charges for applying the required quantity of bitumen including hire and fuel charges for tools and plants etc., complete in all respects as directed by the Engineer or his representative.

Providing and laying of open graded premix carpet with seal coat TYPE - "B' for 20mm consolidated thickness using 0.18 m3 of 13.2mm IRC size HBG crusher metal and 0.09m3 of 11.2mm IRC size HBG crusher metal with 14.60 kg of bitumen of 80\100 grade for pre mixing for 10 m2 of premix carpet and 0.06m3 of clean good sand with 6.8 kg of bitumen for 10 m2 for seal coat Type - B including cost and conveyance of metal and chips to the work site and stacking them to departmental metric gauge for pre measurement including cost of bitumen and all taxes payable which will be procured and supplied by the contractor himself including cost of conveyance of 80/100 grade bitumen to work site and all incidental charges such as storage, handling charges etc. including mixing the materials in the mini hot mix plant for premix carpet only including spreading and consolidation by power roller, rolling including labour, hire and fuel charges for mini hot mix plant and other tools and plants employed etc. cost of all materials labour charges etc., complete in all respects as directed by the Engineer or his representative.

Supplying and laying the Rubber Moulded Hydraulic Pressed machine made 63mm thick inter locking concrete paver block made out of M20 grade concrete of approved design in colour over the bed of M-Sand filling including labour for laying, hand packing and comp etc complete in all respects as directed by the Engineer or his representative.

Open Earth work excavation for foundation with all leads and lifts in all soils and sub soil to the required depth as may be directed except hard rock requiring blasting inclusive of shoring strutting and bailing out water wherever necessary refilling the sides of foundation with excavated earth in layers of 15 cm thickness well consolidated depositing the surplus earth in places shown and levelling the site with all initial leads and lifts etc., complete in all respects as directed by the Engineer or his representative.

With initial lead of 10 m and initial lift of 2 m

With initial lead of 10 m and additional lift of 1 m

Open Earth work excavation for foundation with all leads and lifts and to the required depth in SDR as may be directed except hard rock requiring blasting inclusive of shoring strutting and bailing out water wherever necessary refilling the sides of foundation with excavated earth in layers of 15 cm thickness well consolidated depositing the surplus earth in places shown and levelling the site with all initial leads and lifts etc., complete in all respects as directed by the Engineer or his representative.

With initial lead of 10 m and initial lift of 2 m

With initial lead of 10 m and additional lift of 1 m

Plastering with cement mortar 1:4 (one of cement and four of P-sand) 12 mm thick with water proofing compound at the rate of 1.06 kg / 10 m2 including providing band cornice, scaffolding, finishing smooth, setting, curing etc., complete in all respects as directed by the Engineer or his representative.

Supplying and fixing of Door frame for the following over all size with required dimensions of size~ 100 mm x 75 mm, with groove of size ~ 30 mm x 20 mm for resting the door shutter & chamfer finish at front using CRCA pressed steel box section 18 gauge or 1.25mm thick for door frames including providing holes and fixing wooden blocks for fixing fixtures and fittings and 4 nos of hold fast using the iron angle of 15cm length with split ends one coat of redoxide primer/ chemical arcylic Fabrication and Supply of 35mm thick solid core flush door with teakply on one side and commercial ply on other side with teak wood liping alround with iron oxidised hinges,tower bolts 12" 2 nos with receiver,Aldrop 30 cm and handle 1 no complete in all respects as directed by the Engineer or his representative.

1375mmx2600mm

1000 mmx2600mm

1220mm x 2100mm

910mm x 2100mm

1220mm x 2100mm

Painting the walls with two coats of cement paint of approved quality over one coat of white cement paint including the cost of cement paint, brushes, scaffolding etc., complete in all respects as directed by the Engineer or his representative.

Supplying and fixing of SFRC manhole cover with frame of size 0.60 x 0.60 m (Heavy type) etc., complete in all respects as directed by the Engineer or his representative.

Supplying and fixing of CI Steps of size 14" etc., complete in all respects as directed by the Engineer or his representative.

Wiring with 2 off 1.5 sq.mm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI mark with continuous earth connection by means of 1.5 sq.mm PVC insulated single core unsheathed copper conductor cable of 1100 V grade with ISI mark in suitable PVC rigid pipe 2mm thick with ISI mark on surface run with suitable size concealed 16 gauge M.S. switch box covered by laminated hylem sheet 3 mm thick for 5 Amps 3 pin C.S. plug points at switch board itself including the cost of cable, PVC pipes and specials, brass screws, ceiling rose, flush type 5 Amps SP Mark switch, PVC junction box, 16 gauge M.S. switch box covered by laminated hylem sheet 3mm thick T.W. plugs, cement and labour, circuit mains etc., complete in all respects as directed by the Engineer or his representative.

Supply and delivery of Open well Submersible pump set confirming to IS 14220 /2002 and as amended thereafter and BEE 3 Star Rated capable of discharging the following duties due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze mixed type impeller, CI FG 200 grade casing and brass screws and rotor shall be of copper rod as per IS 613/1984 with ISI mark. The pump suitable for installation in sump with 1.1KV grade 3 core suitable copper flat submersible cable to a length of 15m with necessary cable joints. The non-return valve located at the top of the pump in the discharge outlet connection is to be designed with minimum friction. The pump should be directly coupled to 2880 RPM, three phase, 50Hz (±5), 415V+6% & 415V-15% squirrel cage induction motor suitable for DOL upto 5 HP, Fully Automatic Air break Star Delta up to 20 HP and Auto Transformer starter for above 20 HP starting and for continuous operation etc., complete in all respects as directed by the Engineer or his representative.

Labour charges for the erection of submersible pump sets in bore well / open well including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing the riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches, starter, voltmeter, ammeter, three pilot indicating lamps, capacitor, single phasing preventer, water level guard and laying and jointing cables etc complete in all respects as directed by the Engineer or his representative.

Supply and delivery of direct online starter confirming to IS13947,IEC 60947-1 suitable KW rating for operation AC/three Phase/50HZ(± 5%) and 415 V (±10%) including Ammeter, Voltmeter, Thermal Overload relay, 16Amps 2 pole Magnetic Conductor with under Voltage protection, Indication lamp, starting capacitor, running capacitor and On / Off Push button switches,5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulated cable, powder coated vermin proof box including the capacitor (the cost of capacitor is to be taken separately).testing the pump set and trail run for 10 days. etc complete in all respects as directed by the Engineer or his representative.

Supply and fixing of 6 Way Vertical TPN Distributions boards; IP43 with double door (Metal); with 12module incomers and 18 Single Phase/Three Phase/ MCB’s outgoing; as per IS 8623 III etc complete in all respects as directed by the Engineer or his representative.

Supply and fixing MINIATURE CIRCUIT BREAKERS (MCB) 240 V/415 V 50HZ AC Supply Suitable For Both Lighting And Motor Circuits Single pole 6A to 32A,10 KA (For Lightings) etc complete in all respects as directed by the Engineer or his representative.

Supplying, laying and jointing Of L.T Cable-3.0, 3.5, 4 cores 1.1 kV Grade armoured marking, aluminium conductor cable confirming to IS 1554 and as amended thereafter Part I With ISI etc., complete in all respects as directed by the Engineer or his representative.

Supply and laying PVC Insulated Single Core Multi Strand Fire retardant Flexible Copper cable with IS Mark Conforming to IS 694/1990 etc., complete in all respects as directed by the Engineer or his representative

Supply and fixing suitable T.W. board to get TNEB 63 Amps three phase service connection with 3 nos of 63amps fuse unit (500 volts) 63 amps neutral line and earth line ( 1"x 1/8" ) copper flat on teak wood plank of size 600 mm x 450 mm x 19 mm with supporting Teak wood reapers of 1 " thick on either side with pointing with suitable bolts and nuts for fixing the TW planks on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit etc complete in all respects as directed by the Engineer or his representative. 1) 100 A fuse units, 2) 1 No of neutral link copper flat of size 25x3x150mm 3) 1 No of earth link of copper flat of size 25x3x150mm and 4) Space provision for 3 Phase energy meter

Supplying and fixing of 100 Amps 500volts grade porcelain fuse unit on suitable teak wood plank varnished to be fixed on the top of EB pole with clamps including cost of all materials etc complete in all respects as directed by the Engineer or his representative.

Supply and fixing following dia GI pipe of approved brand having ISI mark etc., complete in all respects as directed by the Engineer or his representative.

40mm dia GI pipe

Labour charges for cutting threading and jointing the following dia of GI pipes with necessary specials including fixing into walls with necessary clamps and screws making holes in the roof making materials packed the same with necessary brick works and plastering wherever necessary with scaffolding etc., complete in all respects as directed by the Engineer or his representative.

40mm dia GI pipe @ inlet

Supplying the following dia GI Pipes specials of approved quality tc., complete in all respects as directed by the Engineer or his representative..

50mm dia GI coupler

50mm dia GI bend

50mm dia GI union

50mm dia Tee

50mm dia GM gate valve

50mm dia Hex nipple

50mm x40 mm Reducer

32mm GM wheel valve

25mm GM Gate Valve

40mm GM Gate Valve

Labour charges for cutting threading and jointing the following dia of GI pipes with necessary specials including fixing etc., complete in all respects (Below GL)

50mm dia GI pipe

Supplying and fixing the follwing dia of UPVC pipes of approved quality at site of work as per table II spcification of ISS 4985 / 1981 in standard length of 6 meter each with one coupler at free of cost for every standard length of pipe. 50mm dia PVC pipe 10Kg / cm²

a) 50mm UPVC Pipe ( 10Kg / cm²)

Supplying and fixing the following UPVC specials of approved quality etc., complete in all respects as directed by the Engineer or his representative.

32mm dia Nipple

32mm dia Tee

25mm dia Elbow

25mm dia Nipple with check nut and washer

25mm dia Tee

25mm × 20mm size Reducer elbow

20mm Dia Screw Down Tap (Heavy)

PVC 32mm Coupling

PVC 32mm Union

50mm dia bend

50mm dia TEE

50mm dia coupler

110mm dia single bend with door

110mm dia single 'Y' with door

110mm dia PVC Elbow

110mm dia PVC Tee

110mm dia plain bend

75mm dia single bend with door

75mm dia single 'Y' with door

75mm dia plain bend

160mm dia bend pipe

160mm dia TEE

200mm dia bend

solvent cement

Supply of using 40mm size ISS hard broken granite stone jelly for foundation inclusive of shoring and strutting, bailing out water, ramming, curing etc complete in all respects as directed by the Engineer or his representative.

Supply of using 20mm size ISS hard broken granite stone jelly for foundation inclusive of shoring and strutting, bailing out water, ramming, curing etc complete in all respects as directed by the Engineer or his representative.

Supply of filling sand in layers 400 cm thick well watered, rammed and consolidated complying with relevant standard specification incl. the cost of filling sand etc complete in all respects as directed by the Engineer or his representative.

Reinforced Cement concrete 1: 2:4 (One of cement, two of M- sand and four of hard broken granite stone jelly using 20mm size broken stone jelly for all reinforced concrete works for petty works, excluding cost and fabrication of reinforcement grills in position, but including centering and strutting, laying, moulding, curing, finishing etc complete in all respects as directed by the Engineer or his representative.

Supplying the following UPVC pipes for plumbing works in building works as per table II specification IS 13592-1992 in standard length of 6 m each with one coupler at free of cost for every standard length of pipe.

160mm dia UPVC Pipe

200mm dia UPVC Pipe

Manufacturing the PCC kerb wall of size 45cm x 23cm x 45cm tk. Made with RCC petty works in cement concrete 1:2:4 (One of cement two of sand and four of hard brocken stone jelly) including proper casting, moulding and curing etc. complete in all respects as directed by the Engineer or his representative. The quantity of RCC kerb wall for 10m length = (1x2x5) x (.45mx0.23mx0.45m height) including pointing the same with cement mortor etc. complete in all respects as directed by the Engineer or his representative.

Supplying and fixing of manhole cover with frame of size of best approved quality of size 0.60M x 0.60M (Heavy type) etc., complete in all respects as directed by the Engineer or his representative.

Supply & run of 2 x 4 Sq.mm of PVC insulated unsheethed single core FR copper cable of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continous earth connection by 1 run of 1.5 Sq.mm PVC insulated unsheathed copper cable of 1100 V grade

Supply and run off 2 of 4 sqmm PVC insulated singlecore unsheathed copper conductor cable of 1100 Vgrade with ISI mark confirming to IS:694/1990 insuitable PVC rigid pipe 1.8mm thick concealed in wall with continuous earth wire connection of 14 SWG TC wire and making good for the concealed portion with suitable colour.

Supply and fixing of TNEB meter Board suitable for 32A Single phase service connection with 32A fuseunit (500V) 32A neutral link and earth link (1" x 1/8"Copper flat) on TW plank of size 375mm x 300mm x19mm with supporting T.W.reepers of 1" thick oneither sider with painting with suitable bolt and nuts forfixing the TW plank on wall with earth connection andinter connection with 7/20 PVC insulated copper wirefrom EB meter to fuse unit.

Supply and fixing of TNEB meter Board suitable for 63 A three phase service connection with 63A fuseunit(500V) 63A neutral link and earth link (1" x 1/8"Copper flat) on teak wood plank of size 600mm x450mm x 19mm with supportingT.W.reepers of 1" thick oneither sider withpainting withsuitable bolt and nuts for fixingthe TWplank on wall withearth connection andinterconnection with 7/20 PVCinsulated copper wirefrom EBmeter to fuse unit.

Supplying and fixing of MS angles of size not less than 37.5mm x 37.5mm x 6.24 mm (1 M=3.25 Kg) including one coat of red oxide primer cutting ,welding,labour for fixing etc complete

Supplying and fixing of 16 Amps DPIC switch of 500V with Face & Neutral (side handle) on suitable T.W. Board of size 30cm x 20cm x 7.5cm including necessary internal connection, earth connection etc., complete in all respects as directed by the Engineer or his representative.

Earth work excavation for foundation with all initial leads and lifts in all soils and sub soils and to the required depth as may be directed except hard rock requiring blasting inclusive of shoring, strutting and bailing out water wherever necessary refilling the sides of foundation with excavated earth in layers of not exceeding 15cm thick well consolidated depositing the surplus earth in places shown and levelling the site with all leads and lifts etc.,complete in all respects as directed by the Engineer or his representative. (Narrow for Drain)

Filling in foundation and basement with River Sand in layers not exceeding 15 cms thick well watered rammed and consolidated complying with relevant standard specification including the cost of supplying river M-Sand etc., complete in all respects as directed by the Engineer or his representative.

Filling in foundation and basement with gravel in layers of not exceeding 15cm thick well watered, rammed and consolidated complying with relevant standard specification including the cost of filling gravel etc., complete in all respects as directed by the Engineer or his representative.

Supplying and fixing in position Indian make white glazed earthen ware lipped mouth Porcelain flat back urinal of best approved quality with GI pipe connection of suitable length 32mm bell mouthed PVC connection, 15mm dia GM wheel valve, 15mm dia B Class GI waste water pipe, 15mm Nylon connection, 15mm dia brass nipple etc., fixing the urinal to the wall in position with necessary TW plugs, clamps, shellac etc., including dismantling masonry if necessary and redoing the same to original condition fixing the 15mm dia GI pipe and wheel valve. Checked without any leakage complete complying with standard specification etc., complete in all respects as directed by the Engineer or his representative.

Supply and erection of Rotational Moulded Polyethylene water storage tanks (HDPE Cylindrical vertical type) for out door use having capacity of 500 litres (excluding free board) with ISI mark (marked with tank itself) with toplid with provision of locking including necessary specials and fittings for storing potable water and manufactured with materials which do not import any taste / odour / any taxic effect and not to contaminate etc., With carbon block content and dispersion in accordance with relevant IS specifications and as directed by the departmental officers. etc. complete (The tank should be got approved from the Executive Engineer before erection) and placed in terrace slab over water tank base slab laid on pedestal 0.90 m above terrace slab.

Brick tiles Dadoing the walls with first quality brick tiles of size 230×75×8mm of approved quality and make and laid in cement mortar 1:2 (one of cement and two of M-sand), 10mm thick and pointing with white cement neatly complete in all respects as directed by the Engineer or his representative.

Supply and fixing of MS horizontal panels for closing the openings using hollow horizontal box section of minimum size 150mm x 150 mm x 1.5mm thickness as including one coat of red oxide primer cutting ,welding,labour for fixing into the required places etc., complete

Supplying and erecting Rolling Shutter of 76 mm 18 gauge of galvanized steel with push and pull or self coiling type operated by pulling hook with top cover including locking arrangements and fixed in position inside or outside etc., complete and painting with priming coat of red oxide without lock. (Payment will be made by only for the actual opening of the shutters are rolled up wherever the shutters are to be fixed) etc., complete in all respects as directed by the Engineer or his representative.

Supply and fixing of following water supply materials at site with best quality tc. complete in all respects as directed by the Engineer or his representative.

32mm dia GI pipe 'B' class

25mm dia GI pipe 'B' class

20mm dia GI pipe 'B' class

Supplying the following dia GI and GM specialsconfirming to ISI etc of approved quality tc., complete in all respects as directed by the Engineer or his representative..

32mm dia GI Coupling

32mm dia GI Tee

32mm dia GI Union

25mm dia GI Union

20mm dia GI Coupling

25mm dia GI Coupling

20mm dia GI Elbow

25mm dia GI Elbow

25mm dia GI Tee

40mm GI Union / Coupler

40mm dia GI Elbow

50mm x 40mm dia GI Reducer

Supplying and filling the basement with Good Earth filling in layers of not more than 15cm thick well rammed watered and compacted - etc., complete in all respects as directed by the Engineer or his representative.

Brick work in cement mortar 1:5 (one of cement and five of M-sand) using Fly Ash bricks of minimum size 23cm X 11cm X 7cm including dewatering wherever necessary, proper setting and curing etc., complete in all respects as directed by the Engineer or his representative

FOR Super Structure

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc. complete as per standard specification ( For Roof Trus works)

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required size and making ornamental designs as per the site condition etc

Supplying and fixing inposition of weldmesh of 75x25mm with 10 gauge etc. complete in all respects as directed by the Engineer or his representative.

Supplying and erecting of modern pull and push type steel rolling shutter made out of 80mm x 1.25mm M.S Laths, interlocked together hrough thier entire length and joined together at the end by end locks mounted on specially designed pipe, shaft with brackets, side guides and arrangements for inside and outside locking with ull and push operation complete. including the cost of providing and fixing necessary 27.5cm long wire springs, including all cost of materials and labour charges for fixing in position and conveyance cost etc, complete in all respects as directed by the Engineer or his representative.

Wiring with 2X 1.5 sqmm (22/0.3) PVC insulated Sc unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with 150x100x113mm TW switch box and 5A 3 pin non inter locking CS plug with painting of suitable color with continuous earth wire connection of 14SWG TC wire for Open PVC plug point etc., complete in all respects as directed by the Engineer or his representative.

Supply and run of 2 of 4Sqmm (56/0.3) PVC insulated SC unsheathed cu. Conductor of 1100V on 7/20 GI bearer wire for service connection mains etc., complete in all respects as directed by the Engineer or his representative.

Supply and run of 2 of 6Sqmm (56/0.3) PVC insulated SC unsheathed cu. Conductor of 1100V in 20mm dia GI pipe with suitable bend on both end for service connection mains etc., complete in all respects as directed by the Engineer or his representative.

Supply and fixing of single box type 24W LED light fitting 4000K 2x2 Square Type Recessed Fitting Higher End ( Philips/havells or equivalent). etc., complete in all respects as directed by the Engineer or his representative.

Supply and fixing of vinyle name board of size 2.40X1.20m with corporation embam and letter TCC School including frame with 50X25mm country wood reeper with 1"X1" Alu bending with all material etc. complete in all respects as directed by the Engineer or his representative.

Fabricating, supply and fixing in position of of MS doors, windows and Ventilators with single or double leaf using MS angle as outer frame, shutter frame and intermediate siffener covered with M.S Sheet with necessary lunges, tower holts, aldrop and hold first complete with one coat of red oxide primer including all cost of materials and labour charges for fixing in position and conveyance cost etc., complete in all respects as directed by the Engineer or his representative.

Door 1 (0.75 x 2.10 m)

Window (1.2 x 0.9m)

Manufacture and Supply of Shredder machine only for segregation garbage should have using MS plate 20mm, 10mrn, 3mm & channel 120 X 65 X 50, channel 75 x 40, L angle 40 x 60 & shaft 60mm dia. Capacity of 1Mt to 1.5Mt / Hour with single shaft cutter, stell grade blade, 10 Hp motor, size 600mm X 800mm X 600mm, chute - yes (Feeding & discharge) with mannual feeding, Electrical - 10HP starter only without cable, total machine height is 2000mm and width 1200mm feeding conveyor -1 No (Mannual) etc, complete in all respects as directed by the Engineer or his representative.

Supply, fixing and commissioning of Belt conveyor length of 6Mtrs and breadth of 1.00m wide for organic waste shorting and conveyor structure should made with MS Heavy Tubes, MS Channels with Gear motor of 2HP / 50RPM / 440V / chain drive motor rollers with heavy rollers - 2 Nos, continuous rollers - 2 Nos and shaft should be ISI standard Bearings, MOC EN 8 make should be of HAVELLS / MARATHAN and the total setup should covered with FRP. The Conveyor should be with branded starter, motor should be heavy duty performance, FRP Hopper with necessary safety guard facilities and all materials should be got approved by the Engineers in charge before fixing in position including cost of all materials and labour charges etc, complete in all respects as directed by the Engineer or his representative.

Supply , erection and commissioning aronmental street light pole to a total height of 8m above ground level and 1m below ground level (125mm dia - 5m height & 100mm dia - 3m height & 80mm dia -1m height) made with 304 grade SS including 2nos. 40W LED street light fitting including all cost of materials and conveyance cost and all cost of errection charges including earth work and PCC for base concrete below ground level etc, complete in all respects as directed by the Engineer or his representative.

Supply and laying of 4sqmm 2core Alu. UG Cable including all cost of materials and conveyance cost and all cost of labour charges etc, complete in all respects as directed by the Engineer or his representative.

Supply and Fixing of incinerator (sanitary napkin burning machine) of size 600mm x 600mm x 900mm with MS Legs whole system made up of mild steel material with LCD Display with temperature and time indication with "PUF" Insulation, easy removing ash collecting tray ensure cleanliness, bigdoor opens makes it convenient to load used napkins, heater of High power of 3000W makes the temperature rise quickly and improve the efficiency, Computerised programmed control panel of 600 to 800 Celcius gives long life for heaters and reduce the electricity bill including all cost of labour, transportation charges, fixing of machine in suitable place as directed by the departmental officers etc., complete in all respects

Supply And Fixing of Fly Catcher power: solar dc power Volts : 240V capacity: catch 20, 000+ flies dimensions: 65*43.5*49.5cm /72pcs 17/16kg material: plastic pp+ pe

Supply And Fixing of Wind Driven Ventilators Exhaust Fan Size: 24 inches No of blades: 38 Product Type: Wind Driven Ventilators Fan Type: Roof Ventilator Material: Aluminium

Supply and erection of Rotational Moulded Polyethylene water storage tanks (HDPE Cylindrical vertical type) for out door use having capacity of 1000 litres (excluding free board) with ISI 12701 / 1996 mark (marked with tank itself) with toplid with provision of locking including necessary specials and fittings for storing potable water and manufactured with materials which do not import any taste / odour / any taxic effect and not to contaminate etc., With carbon block content and dispersion in accordance with relevant IS specifications and as directed by the departmental officers. etc. complete (The tank should be got approved from the Executive Engineer before erection) and placed in terrace slab over water tank base slab laid on pedestal 0.90 m above terrace slab.

Steel Solid waste Containers for waste collection shall be provided with 4 Castor Wheels made of one virgin piece of minimum 200 mm dia and 50 mm width shall have 360 degree with Blocking System. The Sokid waste Collection Bins shall be of 1100 Ltrs Capacity as per DIN Standards. These should be closed type hygienic bins meeting DIN Standards. These Bins should be provided with Bin Cover which opens automatically when the Bin Lifter lifts the Bin on to the machine hopper. For this purpose, the Bins should be provided with special link arrangements, which are operated by the Compactor Bin Lifter. The Bin construction should be of Pressed Steel Sections for ensuring adequate structural strength required for handling with the Compactor Bin Lifter. Bin shall be designed to be easily handled by two Bin Handlers. a) Capacity : 660 Litre (0.666 m3) b) Body : Mild Steel of minimum 2 mm thickness c) Lid: Mild Steel d) Dead Weight : Minimum 70 kg (Approx) e) Load Capacity : 400 kg (Approx) Other Requirements: a) Four heavy duty swivel castors (360º turning) b) Adjustable spring supported lid for easy opening and closing c) Rubber Profile on the lid, which should protect fingers before closing the lid of sections min, 3 cms between body and lid d) Handles on body e) Handles on the lid f) Painted Green/ Blue / Black as specified g) Bins shall be painted with primer and anti-corrosive paints from inside and outside. All the bin locations should be provided with rigid concrete surface

Trenching the soil digging of existing level of ground to a depth of 30cm below the ground and turning down the lower strata of soil to top portion in order to expose the soil borne pathogen if any and to improve the porosity of the soil for better aeration and root penetration etc., complete in all respects as directed by the Engineer or his representative.

Supply & stacking of red earth at site to the departmental gauge for pre measurements which is of light textured , crystalline, porous and friable and no of generally acidic or neutral but not of alkaline and should be fertile, including seigniorage charges, cost of transportation, loading, unloading, stacking and inclusive of all taxes etc., complete in all respects as directed by the Engineer or his representative.

Supply of well decomposed Farm yard Manure in a powdery form, devoid of soil sand, stones, plastics and other materials, highly nutrient and which supports plant growth etc., complete in all respects as directed by the Engineer or his representative.

Mixing charges of Red soil, sand and manure uniformly (1:1:1) for Preparation of soil mixture (excluding material cost) etc., complete in all respects as directed by the Engineer or his representative.

Spreading of red soil, gravel or sand including watering and rolling which hand roller for every 75 mm thickness - including hire charges of roller etc., complete in all respects as directed by the Engineer or his representative.

Planting of Shade G2 grass including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in charge. etc., complete in all respects as directed by the Engineer or his representative.

Supplying , stacking and planting of following plants of height 30-45 cm in polythene bag of dia 20 cm including loading and unloading charges, transportation, stacking of saplings at site, earthwork, of required size, planting of saplings, refilling etc., complete in all respects as directed by the Engineer or his representative.

ORNAMENTAL SHRUBS IXORA ORDINARY

ORNAMENTAL SHRUBS IXORA DWARF

ORNAMENTAL SHRUBS IXORA HYBRID

ORNAMENTAL SHRUBS TABERNUM GREEN

ORNAMENTAL SHRUBS JETROPHA

ORNAMENTAL SHRUBS MEINIA ERECTA

ORNAMENTAL SHRUBS PLUMBAGO

ORNAMENTAL SHRUBS GALPHYMIA

ORNAMENTAL SHRUBS CANNA INDICA

ORNAMENTAL SHRUBS HEMELIA PATTENS

Supply and planting of Avenue trees including earth work excavation for pits of size 30 cm x 30 cm x 60 cm depth filled up with red earth of 30 cm depth manuring with cowdund and sinthetic fertilizer for 30 cm depth planting avenue trees of approved variety to aheight of 2m and above from ground level with bamboo square guard of size 2'x 2' to a height of 6'0" and maintaining trees of six months including watering periodical maintining and safe gurding the Avenue trees all complete in all respects as directed by the Engineer or his representative.

ARM&SHOULDER WHEEL Supply, Erection and Fixing of Arm & Shoulder Wheels 1300 x 1200 x1350 mm 4mm pipe Main Post made of 4 Inch Pipe and other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes Double coat Powder coating, Heavy duty Branded sealed Ball bearing, for long lasting life etc., complete in all respects as directed by the Engineer or his representative.

MULTI FUNCTIONAL TRAINER (KNEE HIP RAISE) Shoulders, Triceps, Abdominals, Back and Leg muscles exercise. Size: (1105mm x 550mm x 1480 mm) Main Post made of 4 Inch Pipe and other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes 4 mm pipe Double coat Powder coating, Heavy duty Branded sealed Ball bearing, for long lasting life etc., complete in all respects as directed by the Engineer or his representative.

AIR WALKER Leg stretching exercise- Improves physical performance body balance aerobic capacity and Flexibility. 1330mm x 525mm x1420 mm) 4 mm pipe Main Post made of 4 Inch Pipe and other main pipes 1-1/2 inch Pipes. Mm thickness pipes Double coated Powder coating, Heavy duty sealed Ball bearing, for long lasting life. etc., complete in all respects as directed by the Engineer or his representative.

ARMAND LEG STRENGTHENER Leg and Arms muscle exercise- Strengthen joint and cardiovascular system. 1435mm x 740mm x 1005mm) 4mm Main Post made of 4 Inch Pipe and other main pipes 1-1 /2 inch Pipes. 3 mm thickness pipes. Thick Rexin covered cushioned Seat & Back rest Double coated Powder coating, Heavy duty sealed Ball bearing, for long lasting life. etc., complete in all respects as directed by the Engineer or his representative.

CHIN UP BAR Upper Arm and Chest muscle exercise: (2630mm x 305mm x 2640mm) 4mm pipe Main Post made of 4 Inch Pipe and other main pipes 1- 1 /2 inch Pipes. 3 mm thickness pipes Double coated Powder coating, Heavy duty sealed Ball bearing, for long lasting life etc., complete in all respects as directed by the Engineer or his representative.

TWISTER (TRIPLE) Supply, Erection and Fixing of LEG PRESS Size: 1500mm x 1500mm x1425 mm, Area of 7.4 Sq Ft Main Post made of 4 Inch Pipe and 26 I other main pipes 1-1 /2 inch Pipes. 3 mm thickness pipes. Double coated Powder coating, Heavy duty Branded sealed Ball bearing, Steel & foot rest / Foot Paddle for long lasting life etc., complete in all respects as directed by the Engineer or his representative.

EXERCISING BAR Size 1800 x 550 x 1700 mm. Main Post made of 4 Inch Pipe and other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes. Double coat Powder coating, Heavy duty sealed Ball bearing, for long lasting life etc., complete in all respects as directed by the Engineer or his representative.

SEATED CHEST PRESS Size (1850 x 800 x 2050 mm) Main Post made of 4 Inch Pipe and other main pipes 1-1 /2 inch 28 I Pipes. 3 mm thickness pipes Thick rexin covered cushioned seat Double coated Powder coating, Heavy duty Branded sealed Ball bearing, Steel Foot rest I Foot Paddle for long lasting etc., complete in all respects as directed by the Engineer or his representative.

ARM WHEEL (DOUBLE) Size (1800mm x 650mm x 800 mm) Main Post made of 4 inch Pipe and other main pipes 1-1/2 inch Pipes. 3 mm thickness pipes Double coated Powder coating, Heavy duty Branded sealed Ball bearing, for long lasting life.

Swing 2 seater: Fibre glass reinforced plastic of height of 7 ft above the ground level and width of 10 ft. Legs made of 40mm stainless steel pipes and cross bars made of 50mm SS pipes seats fibre reinforced plastic seats suspended with 6mm thick in coated chain and including epoxy painting etc., complete in all respects as directed by the Engineer or his representative.

See saw 4 seater: Fibre reinforced plastic of width of 7 feet and supporting frame made of 40mm stainless steel pipes and swinging arm made of 50mm Stainless steel pipes of length 8feet. Handle made of 19mm stainless steel pipes seats are fibre reinforced plastic and including epoxy painting etc., complete in all respects as directed by the Engineer or his representative.

FRP wave Slide 5feet height wave slide made of FRP moulded materials and ladder 1 inch stainless steel pipe and 1/2 inch cross steps supporting of 1 1/4 inch stainless steel pipes etc., complete in all respects as directed by the Engineer or his representative.

Horizontal bars (Push, Pull up chair) Promotes upper body and triceps strength Lat pull down develops upper body strengths size 2900mm X 775mm X 2060 mm main post made of 4 inch pipe and other main pipes 1-1/2 inch pipes. 3mm thickness pipes double coat powder coating heavy duty branded sealed ball bearing, for long lasting life- steel foot rest/ foot paddle for long lasting life etc., complete in all respects as directed by the Engineer or his representative.

Supply and Planting 6 to10 feet height fruit trees from nursery to work site including cost of trees conveyance and labour charges etc.,complete in all respects as directed by the Engineer or his representative.

Supply and Planting 3 to 4 feet height fruit trees from nursery to work site including cost of trees conveyance and labour charges etc., complete in all respects as directed by the Engineer or his representative.

Providing tree guards for protcting the trees by using Country wood reepers of size 50 mm x 25 mm,Casurina props 5 to 8 cm and Chicken mesh including cost and conveyance of all materials etc.,complete in all respects as directed by the Engineer or his representative.

Cement Concrete 1:2:4 (one of cement, two of M-sand and four of hard broken stone) using 20 mm size hard broken granite stone jelly inclusive of shoring, strutting, bailing out water, ramming, curing etc., complete in all respects as directed by the Engineer or his representative.

Supplying and fixing bakelite battern holder straight orangle type and 40 W bulp on suitable T.W.roundblockincluding necessary interal connections, cost of all

Supplying and fixing of 1200 mm (48") AC ceiling fancomplete with stepped electronic 300 W regulator with1 m down rod with fan clamp, side plates and crossarm of size (18") etc., complete in all respects as directed by the Engineer and his representative .

Bar Screen Supplying ,delivery and fixing of one number manual bar screen in SS-304 Size 1.9 m x 0.8 m ,MOC SS304 – Square rod Spacing between bars 15 mm

Influent Transfer pumps Supply and delivery with fixing all required accessories of sewage water Transfer pumps including electrical items and auto level controller to safe guard the dry run (or) over heating for pumping the sewage water from sewage collection tank to SBR tank with the following specifications inclusive of all incidental charges, taxes, loading, conveyance to site, unloading etc., complete in all respects as directed by the Engineer and his representative. Qty : Two (1w+1s) Capacity : 30 m3/hr Type : Multistage High Pressure pump Head : 3 bar Motor : 5 HP MOC : SS304 Make : Grundfos /Equivalant with all complete complying with standard specification and with proper and suitable accessories for erection.

Air blowers with VFD fitted Supply and delivery with fixing accessories of Air blowers including electrical and other accessories for aeration tank for treatment of sewage water with the following specifications inclusive of all incidental charges, taxes, transportation, loading, unloading to site, etc., all complete in all respects as directed by the Engineer and his representative Air Blowers: Twin lobe positive displacement type, rotary air blowers of suitable type with V-belt drive, belt guard, base plate, inlet filter-silencer, flexible connectors, check valve, relief valve, pressure gauge and piping. Qty : Three (2w+1s) Capacity: 600.0 m3/hr Head : 0.6 bar Type :Centrifugal multistage MOC : SS304 Drive : 20 HP Make : KAY / Everest or eqv with all complete complying with standard specification and with proper and suitable accessories for erection

Air Grid system- SBR Tanks Supplying, installing, testing and commissioning, consisting fine bubble diffuser along with membrane from set of EPDM membranes, SS 304 clips PVC support pipe(10 ksc pressure rating),PVC fitting and MS pipe for the headers and distribution with all accessories to make it retrievable & to provide clog-free oxygen for SBR 1 & 2 Tanks. Qty : 1 Lot MOC : EPDM with teflon Type : Fixed type- Circular disc Make : SSI /Southcogan Equivalent

Filter Feed pumps: Centrifugal type,with bronze/SS in impeller of an approved make and complete with with suction and delivery valves and non return valves,suction and delivery headers capable of handling clear water complete with fan cooled induction motor with class B insulation, mounted on a common structural base plate with 100mm dia pressure gauge with gunmetal isolation cock and suitable vibration elimination pads of approved design for pump foundation. Motor to be suitable for 400/440 volts, 3 phase, 50 cycle AC supply with rpm, to suit the corresponding pumps. Cost of all suction and delivery valves, pipes and header ,pressure gauge shall be included in the rate Qty :Two (1w+1s) Flow rate :40.0 m3/hr Discharge Head: 10 bar Type : Centrifugal submersible MOC : CI Drive : 22 HP Make : Grundfos / Equivalent

RAS PUMP with QDC: Supply and delivery with fixing all required accessories of RAS Pump with QDC with the following specifications inclusive of all incidental charges, taxes, loading, conveyance to site, unloading etc., complete in all respects as directed by the Engineer and his representative. Qty : Two (1w+1s) Capacity : 30 m3/hr Type : Submersible multistage pump Head : 8 bar Motor : 13.5 HP MOC : SS304 Make : Grundfos /Equivalant with all complete complying with standard specification and with proper and suitable accessories for erection.

SAS PUMP with QDC: Supply and delivery with fixing all required accessories of SAS Pump with QDC with the following specifications inclusive of all incidental charges, taxes, loading, conveyance to site, unloading etc.,complete in all respects as directed by the Engineer and his representative Qty : Two (1w+1s) Capacity : 15 m3/hr Type : Submersible multistage pump Head : 3 bar Motor : 2.5 HP MOC : SS304 Make : Grundfos /Equivalant with all complete complying with standard specification and with proper and suitable accessories for erection.

Circulation Pump: Supply and delivery with fixing all required accessories of Circulation Pump with the following specifications inclusive of all incidental charges, taxes, loading, conveyance to site, unloading etc.,complete in all respects as directed by the Engineer and his representative Qty : Two (1w+1s) Capacity : 5 m3/hr Type : Centfifugal multistage pump Head : 2.5 bar Motor : 1 HP MOC : SS304 Make : Grundfos /Equivalant with all complete complying with standard specification and with proper and suitable accessories for erection.

Pressure Sand Filter: Supply and delivery with fixing accessories of Pressure Sand Filter of capacity 18 m3 per hour to filter the suspended matter escaped from the clarifier and present in the sand filter of shell size Ø 1 .4 m x 1.5m fabricated out of 6 & 8 mm thick plate with dished end and Ø 0.5M manhole with proper back wash arrangements, cover, strainers, distribution to be provided inlet and outlet. All flanges in inlet and outlet connections shall confirm IS:15328 necessary valves, pressure gauges, fittings to be provided the filter shall be hydro tested to 5 KG / CM2 for duration of 2 hours. Entire sand filter shall be painted with one coat of epoxy zinc phosphate primer and two coats of epoxy finish paint inclusive of all incidental charges, taxes, loading conveyance to site unloading etc., and with proper and suitable accessories for erection,complete in all respects as directed by the Engineer and his representative. (The quality and brand shall be got approved from the Executive Engineer before use) Qty : One Velocity : m3/hr. Diameter : 2.0m Height :2.6m Type of vessel : Cylindrical MOC : MSRL Type of valve : Butterfly valve Filtering media : Sand & Gravels

Activated Carbon Filters: Supply and delivery with fixing accessories of Pressure Sand Filter of capacity 18.75 m3 per hour to filter the suspended matter escaped from the clarifier and present in the sand filter of shell size Ø 1.2 m x 2 m fabricated out of 6 & 8 mm thick plate with dished end and Ø 0.5M manhole with proper back wash arrangements, cover, strainers, distribution to be provided inlet and outlet. All flanges in inlet and outlet connections shall confirm IS:15328 necessary valves, pressure gauges, fittings to be provided the filter shall be hydro tested to 5 KG / CM2 for duration of 2 hours. Entire sand filter shall be painted with one coat of epoxy zinc phosphate primer and two coats of epoxy finish paint inclusive of all incidental charges, taxes, loading conveyance to site unloading etc., and with proper and suitable accessories for erection,complete in all respects as directed by the Engineer and his representative(The quality and brand shall be got approved from the Executive Engineer before use) Qty : one Velocity : m3/hr. Diameter :2.0m Height : 2.6m Type of vessel : Cylindrical MOC : MSRL Type of valve : Butterfly valve Media : Granular Activated carbon & Gravels

Sludge Transfer pump: Supply and delivery with fixing accessories of Sludge Transfer Pumps for pumping the sludge from clarifier tank to aeration tank with the following specifications inclusive of all incidental charges, taxes, loading, conveyance to site, unloading etc.,complete in all respects as directed by the Engineer and his representative all complete complying with standard specification and with proper and suitable accessories for erection. Qty : Two no. (1w + 1s) Flow rate 1.0 m3/hr Head 12 bar Type rotary lobe or screw pump MOC Body : CI, rotor : SS304 Drive 1.0 HP Make Grundfos/Equivalent

Mixer: Supply and delivery with fixing accessories of Mixer with the following specifications inclusive of all incidental charges, taxes, loading, conveyance to site, unloading etc.,complete in all respects as directed by the Engineer and his representative. Qty : 1 Type : Centrifugal Flow rate 100 m3/hr Head 3 bar MOC :SS304 Make : Grundfos/Equivalent

Sludge Digestor: Supply and delivery with fixing accessories of Sludge Digestor Tank with all piping standards with the following specifications inclusive of all incidental charges, taxes, loading, conveyance to site, unloading etc.,complete in all respects as directed by the Engineer and his representative. Inner Lining : MS FRP Size : 1.2 dia X 2.2 HOS x 3mm thk FRP : 2mm thk

Ozonisation system-post treatment: Supply and delivery with fixing accessories of Ozonization system-post treatment with oxygen concentrator, with the following specifications inclusive of all incidental charges, taxes, loading, conveyance to site, unloading etc.,complete in all respects as directed by the Engineer and his representative. Flow Rate : 20gm/hr

Hypo dosing system: Supplying, installing, testing and commissioning of hypo system ,all complete and with proper and suitable accessories for erection, complete in all respects as directed by the Engineer and his representative. (The quality and brand shall be got approved from the Executive Engineer before use) Qty : One Capacity : 0 – 6 LPH MOC of pump : Dosing Tank Capacity : 100 Liters – make Make : / Equivalent

Electro Magnetic/Ultrasonic Flow Meter- Fully Auto: Supply and delivery with fixing Electromagnetic flow meter with all required accessories of, Flow Tube sensor, Digital flow transmitter LCD display, , power rate 240 watts with all incidental charges, taxes, loading conveyance to site unloading etc. Make :E&H/Mitshubishi or eqv Flow range 0-50 cum /hr

UF Feed pumps: Qty : Two (1w+1s) Flow rate : 20.0 m3 /hr Discharge Head : 5 bar Type : multistage centrifugal type MOC : SS316 Drive :5.5 HP Make : Grundfos / Equivalent

UF Backwash Transfer Pumps: Qty : Two (1w+1s) Flow rate : 38.0 m3 /hr Discharge Head : 3 bar Type : multistage centrifugal type MOC : SS316 Drive : 6.5 HP Make : Grundfos / Equivalent

Membrane filtration system: Supply, delivery and installation of UF modules and Skid mounted frames of MS with powder coating, with all standard UPVC pipes and Electrical actuator valves , pumps complete... Qty : One Lot Model : Outside in, dead end flow, with air scouring provision Feed flow rate:3.1 to 9.3 m3/hr each, pH range : 2-11 Turbidity handling : upto 300 NTU Skid :MS with powder coating Type of valves: Electrical Actuated Valve, Dia -2.5" Recovery:96% UF module surface area : 77sqm each , Dia : 8" UF module make : DOW / Equivalent

Pipe lines and valves: Pipe lines and valves: Galvanized Iron pipes (Heavy class) conforming to IS:1239 complete with carbon steel fittings IS:1879 e.g. tees, crosses, plugs, sockets, elbows, reducers, supports and clamps, puddle flanges, etc., cutting chases including painting pipes and fittings with epoxy paint over a coat of primer.,all complete and with proper and suitable accessories for erection, as directed by the Engineer and his representative. (The quality and brand shall be got approved from the Executive Engineer before use) Interconnecting pipes in UPVC with UPVC / CI Valves. Airline piping in MS with CI Valves

Cables & Cables Tray: Supplying and laying all required cables in the BWTP plant inducing cable try and glands ,all complete and with proper and suitable accessories for erection, as directed by the Engineer and his representative. (The quality and brand shall be got approved from the Executive Engineer before use)

Supply and delivery with fixing accessories of Decanter – SCADA assisted with suitable accessories for erection, complete in all respects as directed by the Engineer and his representative Type : Floating Arm type, Electrically actuated, automatic with level sensing, boom length 2.0 m max Rotor and Vanes : SS 304

Supply and delivery with fixing accessories of Level Sensor (wireless for remote) with suitable accessories for erection,complete in all respects as directed by the Engineer and his representative Type : Ultrasonic continuous with local display and scada transmission Range : 0 – 6m Make :E&H/Mitshubishi or eqv

Supply and delivery with fixing accessories of DO Sensor (wireless for remoe) with suitable accessories for erection, complete in all respects as directed by the Engineer and his representative Type : Contact and continuous with pipe shield and auto wiping mechanism Range : 0-4ppm Make :E&H/Mitshubishi or eqv

Supply and delivery with fixing accessories of Presure Transmitter with suitable accessories for erection, complete in all respects as directed by the Engineer and his representative Type : online continuous with local display Range : 0-6m Make :E&H/Mitshubishi or eqv

Lab Equipments: Supply and deivery with fixing accessories of Lab Equipments with suitable accessories for using in the laboratory, as given below. BOD Incubator 1 no COD Incubator 1 no Jar Test Aparatus 1 no Tabe top pH meter 1 no Table top TDS meter 1 no Other glasswaares and ovens as req 1 LS Heating mantle 1 no Microscope 1 no

Erection and Commissioning: Erection and commissioning of STP 0.6 MLD capacity including erection of all mechanical equipments, Electrical control devices with necessary tools and tackles etc.

Earthing Station: Providing Earthing station using pipe electrode as per IS 3043 using 2.5m of 40mm and 1.0m of 20mm B-class GI Pipe including earthwork excavation, brickwork in cement mortar and plastering and cost of funnel. GI nuts, bolts, washers, check nuts .GI Bend reducer and coupling C.I cover of 30x30 cm and including charcoal of 40kgs and 10 kg etc.,all complete.

Diesel Genset: 160 KVA, 415V, 3 Phase, 50 Hz @ 1500 RPM Diesel Generator used for producing Electricity, Electric Start, Water Cooled with KIRLOSKAR Engine Model 4k1080tag2 developing 200 BHP coupled with KIRLOSKAR GREEN Alternator mounted on a common base frame along with Fuel Tank, Starting Batteries with Leads, general accessories etc., as a complete set positioned in a self standing weather proof KG-CPCB Norms-2 typed Acoustic Canopy KG1600WS with necessary fresh air inlet and hot air outlet louvre arrangements as per the specification.

Supplying and Fixing of 300mm dia RCC Hume pipes NP 3 Class with necessary gradient including labour for fixing, jointing and cost of pipe etc all complete in all respects as directed by the Engineer or his representative.

Construction of circular RCC manhole of 1.2m internal dia with Reinforced cement concrete wall of 15cm thick and base slab of 15cm thick of 1:4:8 proportion (One of cement, four of sand and eight of hard broken granite stones ) using 40mm gauge hard broken granite stones including the cost of steel and fabrication of reinforcement grills in position shutterring centering etc., including channeling benching etc., and top covered withextra heavy duty cover slab SFRC slab with frame 600mm(clear opening) including casting and fixing in position and necessary earth work excavation, refilling the sides of foundation in all soils except hard rock requiring blasting etc complete in all respects as directed by the Engineer or his representative.

1.2m depth

1.5m depth

2.00m depth

Ambient Air Quality -Monitoring - For parameters - PM-2.5 & PM-10, So2, NO2, CO

Ambient Noise Quality Monitoring - To identify sources of noise, Noise due to traffic/transportation of vehicles ,Noise due to heavy equipment operations, Duration and variations in noise over time etc the equivalent noise levels shall be monitored.

Surface/Ground Water Quality - pH, Turbidity, Total Hardness

Provisional Sum