SPECIAL REPAIRS TO BUILDING NO. P - 40 AT SOL OF DB AREA PROV UNIT AND PROVN OF SCOOTER SHED AT DB AREA SIGNAL CENTRE UNDER GE CHENNAI

Amount

Surface dressing not exceeding 15cm deep and getting out in soft/ loose soil complete all as specified and directed.

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation or for shafts, wells, cesspit, manholes etc., n.exc 10sqm on plan and getting out in Soft/loose soil complete all as specified and as directed.

Excavation in post holes (or similar holes) in soft/ loose soil each hole n. exc. 0.5 cum, getting out, returning filling in and ramming earth or broken rubble mixed with earth around in layers n. exc. 25cm, watering and removing surplus soil to a distance n. exc. 50m and making good surfaces complete all as specified and directed.

Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L for broken stone or boulders hardcore of gauge n. exc. 63mm, deposited, spread and leveled in layers n. exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

Supply only liquid water proofing compound all as specified and directed.

M&L for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for PCC (1:5:10) type E-2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in water tank base complete all as specified and directed.

M&L for reinforced cement concrete, M-30 (Design mix), using 20mm and below graded stone aggregate as in roof slabs supported on walls, beams and columns in floors, roofs, deck slabs and the like all as specified and directed.

M&L for reinforced cement concrete, M-30 (Design mix), using 20mm and below graded stone aggregate as in roof beams, cantilevers, bressummers, lintels over 1.5m span all as specified and directed.

M&L for RCC (1:1½:3) type A-1 using 20mm graded aggregate as in shelves and the like complete all as specified and directed.

M&L for precast RCC (1:1½:3) type A-1 using 20mm graded aggregate as in manhole covers, landings, chullah hoods, chajjas with plain faces set in cement mortar (1:4) complete all as specified and directed.

M&L for demolition of highly deteriorated portion of RCC beams, pillars, chajjas and lintels etc. at height upto 3.00m and applying based bonding agent Shali SRB latex of STP Ltd or equivalent on concrete surface as per manufacturer's recommendations, casting RCC member cement concrete (1:1½:3) using 12.5mm graded stone aggregate mixed with plasticiser admixture powder STP No. 1 of STP Ltd or equivalent @ 1 kg per 50 kg of cement or in proportion recommended by the manufacturer including necessary formwork complete all as specified and directed. Notes: (i) Grouting of cracks, cleaning of existing reinforcement with rust remover, application of anti corrosive paint and replacement of reinforcement wherever necessary before recasting RCC shall be measured and paid for separately. However, cost factor towards special scaffolding required for carrying out these items of work at various heights shall be deemed to be included in the quoted rates.

All as per item No. 8 but height exceeding 3.00m but n. exc. 6.00m.

M&L cleaning of reinforcement bars of ant dia in any RCC member by scraping and removing the rust completely by using suitable rust removing liquid (Shali Prime RC of STP Ltd or equivalent) and applying epoxy based anti corrosive paint (Shali Prime Zn R of STP Ltd or equivalent) as per manufacturer's instructions including 10mm thick rendering over concrete surface in cement mortar (1:3) mixed with epoxy based bonding agent (Shali Mortar M of STP Ltd or equivalent) in the proportion recommended by the manufacturer as directed.

M&L for brick work with fly ash bricks (old size) straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:6) complete all as specified and directed.

M&L for brick work with fly ash bricks (old size) straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:4) complete all as specified and directed.

M&L for brickwork with old size fly ash bricks straight or curved on plan to any radius in half brick thick walls in cement mortar (1:4) complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, including supports, overhangs, etc. also splays between floors and beams complete of flat rough finished surfaces of concrete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick of flat rough finished surfaces of concrete all as specified and directed.

Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exc. 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc. 10cm but not exc. 20cm wide flat rough finished surfaces of concrete all as specified and directed.

Taking down chowkats (or) frames of any description with shutters (without taking off shutters from the frame) of area n. exc. 1.5 sqm each along with fittings including separating guard bars/ grills/ wire mesh etc., complete all as specified and as directed.

Taking down chowkats (or) frames of any description with shutters (without taking off shutters from the frame) of area exc. 1.5 sqm but n. exc. 4sqm each along with fittings including separating guard bars/ grills/ wire mesh etc., complete all as specified and as directed.

Taking down shutters of any description n. exc. 1 sqm each including all fittings complete all as specified and as directed.

Taking down shutters of any description exc. 1 sqm but n. exc. 2 sqm each including all fittings complete all as specified and as directed.

Taking down shutters of any description exc. 1 Sqm but n. exc. 2 Sqm each and resecuring in the same opening after cutting, easening etc with new iron mongry complete all as specified and as directed.

M&L for second class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with 19mm MS square tube of 19 gauge mitred out at two corners and joined by inserting two Nos of 150mm long brackets of 15mm x 15mm MS square tube inside the drilling 100mm long MS screws using PVC fastener complete all as specified and as directed.

S&F factory made wood free EPS solid PVC moulded door shutter 28 to 30 mm thick (stiles) with 2, 4 or 6 raised panel design with 2 mm thick 3D wood grain moulded PVC sheet Polyurethane painted on the front face and 2mm prelam colour PVC sheet on back face fixed to frame at complete all as specified, directed and shown in sketch relevant to item No. 8104 in SSR Part-II. Note: The quoted rates deemed to include 02 Nos of 125mm size aluminium anodised handle, 03 Nos of 100mm stainless steel hinges and 02 Nos. of 150mm size aluminium anodised tower bolt of extruded section per shutter.

S&F second class hard wood, plain framed, 35mm thick panelled shutters (any number of panels) with rails and panel of 12mm thick veneered particle board with commercial veneering on both faces, the size of rail and stile are as per IS 1003 (part I) Kiln seasoned and chemically pressure treated and fitted to chowkats complete all as specified and as directed.

S&F stainless steel butt hinges, medium weight cold rolled 100mm size ISI marked all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section 200mm long all as specified and directed.

S&F aluminium handles, fabricated type anodised 150mm size all as specified and directed.

S&F aluminium alloy anodised sliding door bolts 300mm long with hasp, staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections all as specified and as directed.

S&F mild steel 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F hasp and staple 100mm size, aluminium anodised safety type with mild steel hinge pin including bolt to hinge plate fixed with screws complete all as specified and directed.

S&F decorative type Harrison rails 20mm dia mild steel CP with designer brackets (one pair in each opening) stops, rollers etc. fixed in repairs complete all as specified and directed.

S&F continuous piano hinges mild steel bright finish or elactro-galvanized width of flap (when open) 30mm complete all as specified and directed.

S&F powder coated (Thickness of powder coating not less than 50 micron) aluminium anodised windows frames of size 100mm x 40mm x 2mm thick including side hung type, wire gauged and glazed shutter of frame section not less than 0.55 kg/m including sash bar, 4mm thick glass panes and aluminium wire mesh with necessary joining cleats, glazing clips, rubber packing complete alongwith, anodised aluminium snap beading screws including provision of 150mm long peg stay (01 No), 100mm size hinges type B-21 (02 Nos), 125mm size handle (01 No) and 2 Nos tower bolts of 125mm in each shutter complete all as specified and directed.

S&F aluminium anodised powder coated (minimum thickness of powder coating 50 micron) window security grills DG 104 with aluminium channel frame and 6mm thick wire section 75mm aperture fixed with joining cleats etc complete all as specified and as directed.

S&F powder coated (Thickness of powder coating not less than 50 micron) aluminium anodised ventilator frame of size 100mm x 40mm x 2mm thick provided with 8 No. louvers of 4mm thick pin headed/ frosted type glass panes of suitable length and 100mm width and aluminium wire mesh fixed with aluminium beading 25mm wide and 1mm thick fixed on outer face of ventilator complete all as specified and as directed. Note: Rates for glass pane, wire mesh, etc. shall be deemed to be include the quoted rates and nothing extra shall be paid on this account. However, security grill shall be measured and paid separately.

M&L for mild steel work in bands, straps, supports of stays, sunshade brackets, hook and pintle hinges, clamps, hold fasts, guard bars, grills bolts etc and similar conforming to FE-290, Gde E 165 complete all as specified and directed.

M&L for 10mm dia and over mild steel TMT bars as in reinforcement cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-500D complete all as specified and directed.

M&L for 6mm to 8mm dia mild steel TMT bars cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-500D complete all as specified and directed.

M&L for mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to Fe-500D complete all as specified and directed.

M&L framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw including bending and welding angles, as necessary, gusset plate, riveting etc. n. exc. 10kg each brackets conforming to FE-290, Gde E 165, complete all as specified and as directed.

M&L for steel tubular trusses including special shaped washers etc, complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 including one shop coat of zinc chromate primer paint (including preparation of surfaces) at contractor's workshop before fabrication complete all as specified and directed.

M&L plates (plian or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachemnt of Gde Fe 410-W (Gde-E-250) quality-A complete all as specified and directed.

S&F Pre-painted galvalume aluminium zink coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength 550Mpa as in roof covering fixed with self tapping screws as per manufacturer’s instruction complete all as specified and directed.

S&F plain, galvanised, mild steel sheeting 1.00mm thick with grade of zinc coating 275 as in trap door all as specified and directed.

S&F pre-laminated particle board 18/ 19mm thick, exterior grade pre-laminated on one side with decorative choice lamination and other side balancing white lamination fixed with screws as in cupboard shutters and shelves etc. fixed in repairs complete all as specified and directed.

M&L for APP modified prefabricated polymeric membrane, 3mm thick of weight not less than 3.6Kg/ Sqm reinforced with non woven polyester matt, black finished on cold sticker and torch application of membrane with 10cm over lap after necessary preparation of roof surface over 10mm thick screed in cement mortar (1:4) when concrete is green with WPC as per manufacturer's instructions including water proofing treatment consisting of the following all as specified :- (i) One coat of bitumen primer @ 0.40 Kg/Sqm. (ii) One coat of bonding material of blown type bitumen of grade 85/25 heated with working temperature of 180 degree Cent and applied @ 1.20 Kg per square meter of the surface area. (iii) A layer of APP modified polymeric membrane of specified thickness and weight. (iv) Top most layer of surface finished with one coat of heat resisting aluminium paint. (v) Rate of WPC shall be inclusive in the quoted rate and nothing extra will be paid.

Demolition of floor hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises to outside MD land etc., complete all as specified and as directed.

M&L 75mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in floor finished fair and even complete all as specified and directed.

M&L 75mm thick PCC (1:3:6) type C-2 using 40mm stone graded aggregate as in plinth protection including filling of joints by bitumen and sand in ratio (1:2) complete all as specified and directed.

M&L 100mm thick PCC (1:4:8) type D-2 using 40mm stone graded aggregate as in sub base of floors finished fair and even complete all as specified and directed.

M&L 50mm thick PCC (1:2:4) type B-1 using 20mm graded stone aggregate as in floor finished fair and even complete all as specified and directed.

S&F coloured glazed designer ceramic wall tiles as in vertical surfaces of size 300mm x 450mm x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick rendering in cement mortar (1:4) complete all as specified and as directed.

M&L 25mm thick cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as in sub floor finished fair and even complete all as specified and directed.

M&L Non skid coloured ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tiles exceeding 0.11 Sqm but not exc. 0.18 Sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7mm to 8mm thick (Square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in cement mortar (1:4) complete all as specified and directed.

M&L machine cut Kota stone slab 20-25mm thick as in flooring laid over and including 15mm thick screed bed in cement mortar (1:6), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L machine cut Kota stone slab 20-25mm thick as in riser of steps, skirting, dado & pillars etc. laid over and including 15mm thick backing coat in cement mortar (1:4) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete all as specified and directed.

M&L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and the like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite stone including cutting & polishing laid over and including 15mm thick screed in cement mortar (1:6) including making hole for gas pipe and dismantling the old stone complete all as specified and directed.

Taking down cement plaster on brick work or stone walls etc. including racking out of joint, hacking for key, scrubbing down with water etc. and removing the debris outside MD land complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:6) on other than fair faces of brick work or concrete surfaces finished the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces finished the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15mm thick in two coats i.e. 1st coat 10mm thick in cement mortar (1:6) and 5mm thick finishing coat in cement mortar (1:4) mixed with PIDI PROOF LW compound @ 200ml per bag and finishing the surface fair and even complete all as specified and directed. Note: Supply only of water proofing compound shall be measured and paid for separately under appropriate item of this BOQ.

M&L for 5mm thick rendering in cement mortar (1:3) as on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for 10mm thick rendering in cement mortar (1:3) as on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of weather proof exterior acrylic emulsion paint (Apex Ultima of Asian or Weather coat of Berger or equivalent of other specified makes) over a coat of white primer complete all as specified and as directed.

M&L for preparation of old decorated plastered surfaces of walls including brooming down or by steel wire brushing, scrapping down smoke soot, moss and efflorescent salts and treating oil & greasy spots and applying Two coats of white wash complete all as specified and as directed.

M&L for preparation of old decorated plastered surfaces of ceiling including brooming down or by steel wire brushing, scrapping down smoke soot, moss and efflorescent salts and treating oil & greasy spots and applying Two coats of white wash complete all as specified and as directed.

M&L for applying three coats of white wash on ceilings including preparation of newly plastered surfaces complete all as specified and directed.

M&L for applying two coats of colour wash over a coat of white wash on walls including preparation of newly plastered surfaces complete all as specified and directed.

M&L for complete removal of existing treatment on wall surfaces and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of newly plastered surface of walls and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and directed.

M&L preparation of new steel surfaces of any description not otherwise described over 10cm girth or width and applying two coat of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of new wooden or wood based surface of any description exceeding 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of old treated wooden or wood based surface of any description exceeding 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron works new or old treating ends of posts, back of chowkats etc with tar or coal tar black paint area tarred exc. 0.1 sqm but n. exc. 0.5sqm each complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials, steel and iron works new or old treating small articles such as hold fast etc with tar or coal tar black paint area tarred n. exc. 0.1sqm each complete all as specified and directed.

S&F galvanised steel water tubing 15mm bore medium grade including provision of all pipe fittings such as bends, tees, elbows, reducers, unions, plugs, sockets etc fixed to walls, concealed in walls/ ceilings or laid in floors etc, including taking up or down the existing GI tubing complete all as specified and directed.

S&F galvanised steel water tubing 20mm bore medium grade including provision of all pipe fittings such as bends, tees, elbows, reducers, unions, plugs, sockets etc fixed to walls, concealed in walls/ ceilings or laid in floors etc, including taking up or down the existing GI tubing complete all as specified and directed.

S&F galvanised steel water tubing 25mm bore medium grade including provision of all pipe fittings such as bends, tees, elbows, reducers, unions, plugs, sockets etc fixed to walls, concealed in walls/ ceilings or laid in floors etc, including taking up or down the existing GI tubing complete all as specified and directed.

S&F 500 litre capacity three layered rotational moulded polyethelene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position including dismantling existing OHT complete all as specified and directed.

S&F ball valve PTMT with epoxy coated aluminium rod for 20mm bore pipe, weight not less than 210gms, high pressure with polyethylene high density float and complete screwed for iron pipe fixed in repairs complete all as specified and directed.

S&F gun metal, globe or gate valve with iron wheel head, screwed both ends for 20mm bore iron pipe and fixed in repairs complete all as specified and directed.

S&F 15mm dia bib taps cast copper alloy, fancy type chromium plated with crutch or butterfly handle screwed down, screwed for iron pipes or for brass ferrule and fixed in repairs complete all as specified and directed.

S&F 15mm dia fancy type pillar taps cast copper alloy with capstan heads chromium plated screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipes fixed in repairs complete all as specified and directed.

S&F 15mm dia chromium plated fancy type angle stop valve with long shank & cup cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fixed in repairs complete all as specified and directed.

S&F 15mm PVC connection 450mm long with brass nuts fixed in repairs complete all as specified and directed.

S&F in repair brass chromium plated shower rose 125mm, 190mm long shower arm fixed to steel pipe or union complete all as specified and directed.

M&L vitreous china wash down water closet pedestal pattern white with including white coloured PVC seat cover including connections to drain (or outgoing pipe) and flush pipe etc. fixed in repairs complete all as specified and directed.

S&F PVC low level flushing cistern 10 ltr with complete accessories such as PVC flush pipe, over flow pipe etc. fixed in repairs complete all as specified and directed.

S&F vitreous china wash basin white flat back size 550 x 400mm including cutting for and pinning in the ends of bracket or erecting stand but excluding tap, waste chain, plug and porcelain stopper but including brackets and 32mm dia PVC waste coupling with waste pipe fixed in repairs complete all as specified and directed.

S&F in repair 600mm x 450mm bevelled edged looking mirror 6mm thick with aluminium frame work fitted with 6mm thick commercial ply or AC sheet backing to mirror complete all as specified and directed.

S&F in repairs corner glass shelf superior quality, chromium plated (MCH/ Colour CP) with brass bracket as per Cat No. BEA-45 of Prayag or equivalent from other makes specified in particular specifications complete all as specified and directed.

S&F in repairs stainless steel 1mm thick kitchen or laboratory sink with draining board with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of size 40 x 40 x 6mm MS angle iron and connecting union to pipe overall size 914mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repairs SS towel rail as per Cat No. BA-10S of Prayag or equivalent from other makes specified in particular specifications complete all as specified and directed.

S&F PTMT shelf with and including chromium plated brass screws and wooden/ plastic cleats (minimum weight 300 g) fixed in repairs complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/ floors etc. including demolition and breaking up existing pipe complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/ floors etc. including demolition and breaking up existing pipe complete all as specified and directed.

S&F 110mm dia PVC (SWR) bend any radius all as specified and directed.

S&F 75mm dia PVC (SWR) bend any radius all as specified and directed.

S&F PVC (SWR) junction single (single 'T') equal or unequal 110mm bore with access door complete all as specified and directed.

S&F PVC (SWR) junction single (single 'T') equal or unequal 75mm bore with access door complete all as specified and directed.

S&F in repairs 110mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F in repairs PVC (SWR) floor trap, plain with grating including joining with solvent cement 110mm dia of outlet complete all as specified and directed.

Demolition of brick masonry built in cement mortar including all quoins, arches, pillars etc. but excluding ashlars facings, dressed stone work including removal of rubbish outside MD land complete all as specified and as directed.

Demolition of cement concrete in ground floor and paving not exceeding 15cm thick below or above GL including removal of debris to outside MD land complete all as specified and as directed.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, stair landings, chajjas and similar suspended works complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any situation not otherwise specifically provided for complete all as specified and directed.

M&L for point wiring complete with 2.5sqmm (nominal area) PVC insulated unsheathed multi-stranded, (for Phase and Neutral) copper conductor FR & LS grade cable of 1100V grade conforming to IS -694 drawn through and including 20mm bore non metallic rigid PVC conduit medium grade, ISI marked, with conduit accessories concealed In wall/ floor and fixed on ceiling/ roof etc. including pressed steel terminal boxes 1.6mm thick, concealed in walls with plastic laminated sheet cover 3mm thick as top cover fixed with cadmium plated screws for housing the switch sockets, outlets, fan regulator etc including provn of 2.5sqmm PVC insulated unsheathed copper conductor cable of green colour for earth continuity and connecting to common earth dolly complete all as specified for one socket outlet (plug point) three pin 15 Amps controlled by one switch 15 Amps on independent board including taking down existing point wiring complete all as specified and directed.

M&L for point wiring for one light point controlled by one switch complete with 1.5sqmm (nominal area) PVC insulated unsheathed multi-stranded, (for Phase and Neutral) copper conductor FR & LS grade cable of 1100V grade conforming to IS -694 drawn through and including 20mm bore non metallic rigid PVC conduit medium grade, ISI marked, with conduit accessories concealed In wall/ floor and fixed on ceiling/ roof etc. including new pressed steel terminal boxes 1.6mm thick concealed in walls with plastic laminated sheet cover 3mm thick as top cover fixed with cadmium plated screws for housing the switch sockets, outlets, fan regulator etc including provn of 1.5sqmm PVC insulated unsheathed copper conductor cable of green colour for earth continuity and connecting to common earth dolly including taking down existing point wiring complete all as specified and directed.

All as per item No. 102.00 but for one exhaust fan point/ fan point controlled by one switch through regulator.

All as per item No. 102 but for one 3 pin socket outlet on independent board.

All as per item No. 102 but for one 3 pin socket outlet on the same board with other switches.

All as per item No. 102 but for one light point controlled by two number two way switches.

All as per item No. 102 but for bell point controlled by bell push.

M&L for point wiring complete with 4.0sqmm (nominal area) PVC insulated unsheathed multi-stranded, (for Phase and Neutral) copper conductor FR & LS grade cable of 1100V grade conforming to IS -694 drawn through and including 20mm bore non metallic rigid PVC conduit medium grade, ISI marked, with conduit accessories concealed In wall/ floor and fixed on ceiling/ roof etc. including pressed steel terminal boxes 1.6mm thick, concealed in walls with plastic laminated sheet cover 3mm thick as top cover fixed with cadmium plated screws for housing the switch sockets, outlets, fan regulator etc including provn of 4.0sqmm PVC insulated unsheathed copper conductor cable of green colour for earth continuity and connecting to common earth dolly complete all as specified for AC and geyser point on independent board including taking down existing point wiring complete all as specified and directed.

S&F switch socket combination, 5/ 16 Amp, 230 volts, 5 in 1, flush type all as specified and directed.

S&F switch piano, flush type, single pole, one way, 5 Amps, 230 volts all as specified and directed.

S&F switch piano, flush type, single pole, two way, 5 Amps, 230 volts. All as specified and directed.

Supply and fix bell push, flush type, single pole, 5 Amps, AC, 230 volts all as specified and directed.

S&F call bell of multi music type, single pole, AC, 230 volts all as specified and directed.

S&F switch socket combination, 2 in 1, 5 Amps, 230 volts flush type all as specified and directed.

S&F ceiling rose PVC/ polycarbonate body 65 x 50mm; 2 to 3 terminals 230 Volts, AC Single phase all as specified and directed.

S&F stepped flush type electronic ceiling fan regulator 300 watt all as specified and directed.

Supply and fix 20 watts surface and wall mounted LED batten with aluminium housing and integrated electronic driver including 20W LED tube all as per Cat No. LUMLINEPLUSBS20WLED865SPCSS of Havells or equivalent of other specified makes including taking down old fitting complete all as specified and directed.

Supply and fix 10 watts surface and wall mounted LED batten with aluminium housing and integrated electronic driver including 20W LED tube all as per Cat No. LUMLINEPLUSBS10WLED865SPCSS of Havells or equivalent of other specified makes including taking down old fitting complete all as specified and directed.

M&L for submain wiring complete with two runs of 4.0 Sqmm single core, multi-stranded, FR PVC insulated unsheathed cable 1100 volts grade with copper conductor, drawn through and including rigid non metallic PVC conduit medium grade 25mm external dia fixed on wall/ floor/ ceiling along with conduit fittings and accessories, fixed on ceiling with one run of 4.0 Sqmm PVC insulated unsheathed copper conductor cable as earth continuity conductor and connecting to common earth dolly including taking down existing submain wiring with conduit any type complete all as specified. Note: Two runs of 4.0sqmm multi-stranded cable and one run of 4.0sqmm cable as earth continuity conductor alongwith PVC conduit shall be considered as one unit length.

M&L for submain wiring complete with two runs of 6.0 Sqmm single core, multi-stranded, FR PVC insulated unsheathed cable 1100 volts grade with copper conductor, drawn through and including rigid non metallic PVC conduit medium grade 25mm external dia fixed on wall/ floor/ ceiling along with conduit fittings and accessories, fixed on ceiling with one run of 6.0 Sqmm PVC insulated unsheathed copper conductor cable as earth continuity conductor and connecting to common earth dolly including taking down existing submain wiring with conduit any type complete all as specified. Note: Two runs of 6.0sqmm multi-stranded cable and one run of 6.0sqmm cable as earth continuity conductor alongwith PVC conduit shall be considered as one unit length.

Supply, fix, connecting and testing isolator four pole, 63 Amps, 415 volts including taking down the existing one complete all as specified and directed.

Supply, fix, connecting and testing factory made, MCB distribution board (MCB DB), IP 42, TPN, 6 way, 415 Volts, double door, flush type made out of 1.2mm thick CRCA sheet metal, Phosphatised, duly powder coated and conforming to IS 13032 with 200 Amps rated bus bar, neutral link, earth bar and din rail etc., complete fixed in switch board/ wall including taking down the existing one complete all as specified and directed. Note: MCBs shall be measured and paid separately.

Supply, fix, connecting and testing factory made, MCB distribution board (MCB DB), IP 42, SPN, 8 way, 240 Volts, double door, flush type made out of 1.2mm thick CRCA sheet metal, Phosphatised, duly powder coated and conforming to IS 13032 with 200 Amps rated bus bar, neutral link, earth bar and din rail etc. complete fixed in switch board/ wall including taking down the existing one complete all as specified and directed. Note: MCBs shall be measured and paid separately.

Supply, fix, connecting and testing MCB single pole (MCB SP), 6 to 32Amps, 240 volts of rupturing capacity 10kA, C curve type including taking down the existing one complete all as specified and directed.

S&F single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 32 Amps, 230 Volts including taking down old one complete all as specified and directed.

S&F LED street light luminaire outdoor type 20 Watts new generation energy saving and environment friendly long life versatile pressure die cast aluminium IP66 roadway luminaire with high power LEDs as high light source and electronic driver suitable for operation on AC single phase 220-240 volts, 50 Hz supply, including provision of two single core 4 sqmm copper conductor PVC insulated, 1100 volts cable not less than 8 metre long and making connection from junction box of pole including taking down old fitting complete all as specified and directed. Make: Havells Cat Part No. INDURAPEARLLEOSL20WLED 787SASYTOPC 9405 or equivalent of other specified makes.

Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.3mm thick burried directly in ground vertically to a depth not less than 2.25m deep below ground level with top edge of plate not less than 1.5 below ground level connected to GI 4mm earth wire by means of bolts, nuts check nuts washers made of galvanised iron or steel earth wire protected by GI pipe 15mm bore light grade connected upto switch board including 20mm bore GI water pipe with funnel and wire mesh all as shown in electrical plate No. 3 of MES Schedule Part I including dearth chamber of PCC (1:2:4) type B-1 using 20mm grade aggregate with 40mm thick RCC cover slab (1:1½:3) type A-0 using 12.5mm graded stone aggregate reinforced with 8mm dia TMT bars @ 100mm c/c both ways and 6mm dia MS lifting hooks including testing on completion complete all as specified and as directed.

M&L bracket fabricated out of 40mm dia GI light grade pipe 2 metre long bent to shape as directed and fixing to pole with brackets of suitable size complete all as specified and directed.

Supply & fix exhaust fans AC single phase 230/ 240 V of size 300mm sweep with louver fixed in replacement of existing exhaust fan complete all as specified and directed. Note: old fan to be deposited in MES store yard of GE Chennai after fixing new fan.

Taking down existing energy meter for carrying out repairs to building, keeping in safe custody and refixing in the same location/ quarter after repairs have been carried out complete all as specified and as directed.

Taking down carefully, dismantling and opening ceiling fan/ exhaust fan of any size/ any make after disconnecting the electric connection for attending repairs, reassembling, refixing and re-connecting the fans to ceiling rose/connector after necessary servicing and replacing the spare parts etc., complete all as specified and as directed. Note: (i) Supply only of spares and painting will be measured separately. (ii) Servicing like cleaning, application of lubricant oil/ grease, replacement of pins, nuts, bolts etc is deemed to be included in the quoted rates.

Supply only condenser 2.5 Mfd capacity for any make/ sweep/ type of fans, conforming to relevant IS specification and as directed.

Supply only condenser 4 Mfd capacity for any make/ sweep/ type of fans, conforming to relevant IS specification and as directed.

Supply only ball bearing of size 6201 suitable for any make/ sweep/ type of fans, conforming to relevant IS specification. Make: SKF/ TATA/ NBC

Supply only ball bearing of size 6202 suitable for any make/ sweep/ type of fans, conforming to relevant IS specification. Make: SKF/ TATA/ NBC

Supply only gun metal bush for any make/ sweep / type of fans.

Supply only canopy plastic with fixing arrangement, top and bottom for ceiling fan of any make/ sweep as specified and directed.

Supply only rubber bush real type suitable for 1200/ 1400/ 1500mm sweep ceilings fans of any make as specified and directed.

M&L for applying one coat of synthetic enamel paint with gun spray for any sweep/ make of ceiling/ wall mounting fans including filling the cavities with filler after cleaning, scraping all dust/ rust on fans/ down rods/ blades etc., and numbering the fans "MES NO" with black enamel paint complete all as specified and directed.

SIRITEL SYSTEMS PRIVATE LIMITED