REPAIR/ REPLACEMENT OF ROOF TREATMENT, PLASTERING, GUNNITING, ROOF SHEET, TRUSSES, JOINERY, PLUMBING, SANITARY AND OTHER CONNECTED MISC WORKS FOR OT, ICU, ADM BLDG, OFFR MESS AND OTHER OTM/ MD ACCN IN ZONE-A AT BHDC UNDER GE (EAST) DELHI CANTT-10

Amount

Taking down cement plaster on brick or stone walls etc. including raking out of joints, hacking for key, scrubbing down with water etc. of any description complete all as specified and as directed.

M&L 15mm thick rendering in cement mortar 1:6 on brick or concrete surfaces of walls, finished the surface fair and even without using extra cement complete all as specified and as directed.

M & L 15 mm thick rendering in cement mortar (1:4), on brick or concrete wall surface, mixed with water proofing compound @ 3% by weight of cement, finished fair & even without using extra cement complete all as specified and as directed.

M & L 10 mm thick rendering in cement mortar (1:3) on ceiling surface, finished even & fair without using extra cement complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and as directed.

M&L 25 mm thick PCC 1:2:4, Type B1, using 20 mm graded stone aggregate, below tiles for levelling of existing surface complete all as specified and as directed.

S&F Glazed coloured Vitrified tiles 8-9 mm thick (square/ rectangular) polished, area of each tiles Not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match the shade of tile over and including 15mm thick screed bed in CM 1:6 complete.

S&F Glazed coloured Vitrified tiles 8-9 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match the shade of tile over and including 15mm thick screed bed in CM 1:6 complete.

M&L glazed coloured ceramic tiles, 600x300x7mm thick, in vertical surfaces such as skirting/dado etc, set and jointed in cement slurry, laid over & including 10mm thick rendering in cement mortar 1:4, set, jointed and pointed in white cement mixed with colour pigment to match the shade of tile complete all as specified and as directed.

M& L for 16 mm thick Sand stone cladding/Facing tiles gang saw cut with machine cut edges, uniform Size, colour of each stone polishing, rubbing & including silicon treatment between two stone for wall any height over and including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

Taking down of chowkhat or frame (without taking off shutter from frame) area not exc 1.50 Sqm each including builder hardware fitting complete all as specified and as directed.

All as per item No 11.00 here in Before but area exc 1.50 Sqm & not exc 4.00 Sqm each complete all as specified and as directed.

Taking down shutters of any description area exc 1.00 Sqm but not exc 2.00 Sqm each leaf including builder hardware fitting complete all as specified and as directed.

S&F powder coated aluminium of various section as required for frame of door/window/ventilators etc with one or more rebates including jointing cleats for fixing etc. & fixed with cadmium plated screw not less then 300 mm C to C & cealing the joints between frames & granite/kota stone/Wall with polysulphide sealant as per the manufacture's instructions all as specified and directed.

S&F powder coated aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21100mm long (2Nos.) suitable handle (1 No) complete all as specified

S&F powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws with door lock etc. complete all as specified complete all as specified

S & F in Repair powder coated aluminium anodised section 40 x 44mm x14 gauge for aluminium partition wall in wall in panel 1m x1m covered with 5mm thick plain/frosted tinted glass on top half portion and 5 mm thick ACP sheet fixed in half bottom portion including V beading at Aluminium Grill edges complete all as specfied and directed.

S&F aluminium Powder Coated grill with and including suitable aluminium anodised frame including V - beading at all edges as requird manufactured by M/S Decogrill as per design No DG- 104 or equivatent 7.5 mm thick all as specified and as directed by Engr- in- charge.

Providing and fixing factory made UPVC white colour Sliding window Three track area not exceeding 2.00 Sqm each made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and required accessories. (Note: The unit rate quoted by contractor encludes cost of glass and all other connected accessories. Net Opening will be measured for payment purpose.)

Supply and fixing factory made UPVC white colourfixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.

S&F in repair brass mortice lock 100mm 4 lever vertical type with duplicate key and handle set complete all as specified.

S&F in repair Door closer, Powder Coated aluminium body hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete.

S&F 100mm size, stainless steel butt hinges, fixed with Stainless steel screws complete all as specified and as directed.

S&F150 mm long Powder Coated aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

S&F 200 mm long Powder Coated Stainless steel handles, Fancy type and fixed complete all as specified and as directed.

S&F Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Demolition of unreinforced cement concrete in ground floors and pavings not exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F mild steel rolled sections, Framed work as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates, using FE-290 (Gde-E-165) complete all as specified and directed.

S&F in repair, in position Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet, 0.50 mm thick of approved colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, Chajja etc fixed with self tapping screws as specified, high tensile alloy steel trap sheet having 55 MPA yield strength and zinc (galvanized ) + Aluminium combined, coating of 150 GSM /PM2(AZ-150) of 50mm TCT having top colour coat of regular modified polyester/silicon modified polyester/HDEP polyester of 18 to 20 micron and back coat of 5 to7 micron Epoxy primer fixes, RMR 1040 profile width 1125 mm complete all as specified & as directed.

All as per item No 31.00 here in before but plain sheet as in ridge/valley/gutter complete all as specified & as directed.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets and frame work etc complete all as specified and as directed.

S&F Solid PVC Wall Panelling consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed.

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame acomplete all as specified and directed.

M&L false ceiling using powder coated grid system of GI modular grid size 600 x 600 mm with runner 38x24x1.5 mm cross tee 25x24x1.5 mm and wall angle 24x24x1.5 mm thick PVC laminated Gypsum tiles of size 600 x 600 mm of different designs with rear side MPL film fitted in the grid, grid system hanges by 6 mm dia GI wire to purlin, trusses; RCC slab of the roof etc. with hold down clips, butterfly clips, height fixtures etc, complete all as specified and directed.

Providing and fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) with semi perforated 12mm thick micro tegular edged false ceiling tiles of size 595 x 595mm of approved texture, design and pattern having moisture content less than 2%, humidity resistance of 90%, NRCO 0.50 to 0.75 as per IS 8225:1987, Nocumbustible as per BS 476 (Part-4) -1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspende on interlocking metal T Grid of hot dipped galvanised iron section of 0.33mm thick (Galvanised @ 120 Grams per sqm including both side) comprising of main T runners of size 15 x 32mm length 3000mm, cross T of size 15 x 32mm length 1200mm and secondary intermediate cross -T of size 15 x 32mm of length 600mm to form grid module of size 600 x 600mm, suspended from ceiling using galvanised mild steel items (galvanising @ 80 grams per sqm) i.e. 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape lever adjuster of soze 85x25x2mm, Galvanised iron parimeter wall angle of soze 24 x 24 x 0.40mm of length 3000mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per sepcifications, drawing and as per direction of Engineer-in-Charge. (Make: DIAMOND/ GYPROC/ USG BORAL/ KNAUF/ ARMSTRONG)

S&F 10 mm thick toughened frosted glass door shutters of size area exc 1.50 Sqm but not exc 3 Sqm, including necessary floor spring hydraulically regulated, other side fixed on pivot CP fittings and fixtures, CP handles 300 mm long, CP locking arrangement, necessary cutting & holes moulding and fixed including engraving, emblem and lattering not exc 200 mm complete as per directed by Engr-in-Charge.

M & L in repair 18 to 20 mm thick Granite slab (Z Black) work (table rubbed and polished), in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite & half curving the edges of granite stone slab, over and including 20mm thick screed in cement mortar 1:6 including dismantling of old stone slab complete all as specified and as directed.

S&F in repair PVC Cistern kit for one piece EWC Soap Dispenser Glass Bottle complete all as specified and directed. Make : Jaquar Model No ACN-1135 N or equivalent in Marc/ Kohler.

M&L preparation of new plastered wall surfaces and applying two coats of Oil Bound Distemper a coat of interior primer and 3 mm thick cement based wall care putty complete all as specified and as directed.

M&L preparation of new plastered wall surfaces and applying two coats of weather proof Exterior emulsion paint of colour & shade as approved (Colour scheme shall be as approved by the GE & user) over and including a coat of exterior primer and 3 mm thick cement based wall care putty complete all as specified and as directed. Make - Asian Apex Ultima or equivalent of make specified in PS.

M&L preparation of new plastered ceiling and applying three coat of white wash complete all as specified and as directed.

M & L for preparation of old decorated, wall surface by scrapping by electrically operated grinder machine/electric regmal machine and applying one coat of wall care putty on patches surfaces then scrubbing by sand paper to prepare a even surface and applying priming paint followed by applying one coats of OBD of any colour washing down with water complete all as directed. (Asian Paints,Berger)

M&L for preparation of old decorated, wall, roof (corrugal) surface, by brooming and removing all loose layers of old treatment, efflorescence soot and moss by wire brush and filling all nail holes and patches with cement based wall care putty and applying one coat of weather proof Exterior emulsion paint of colour & shade as approved (to match with the Existing surface) complete all as specified and as directed. Make- Asian Apex Ultima or equivalent of make specified in PS. Note: Quoted rates shall deemed to be includs painting at any height including scaffolding work, as required.

M&L for preparation of pathway/Flooring (Over Interlocking/Chequired tile surface) or any type of surfaces old/New or any position and applying one coat of floor paint of superior quality complete all as specified and as directed.

M&L for preparation of new or previously untreated steel surface of any description not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paints over and including one coat of red oxide primer complete all as specified and as directed.

Supply and fabrication & fixing of Modular wardrobe,cupboards, cabinets, drawers , shelfs, vanity , dressing table including shutters ( depth of 45 Cm up to 70 Cm) etc , all front side, bottom, top, two sides and partions etc made out of 15-18 mm thick HDHMR board and back side made out of 8 - 10 mm thick HDHMR board (Action tesa or equivalent ) with machine pressed 0.5 to 0.8 mm thick fabric/glossy colour laminate on all exposed front side and other sides decorative laminations . All exposed edges of boards with machine pressed edge band 0.8mm from rehau Germanetc (colour of laminates , design & paterns of partations/ etc as approved by GE) including all accessories of fittings - Auto/soft closing hinges for shutters , C/J gola profile for handel less, telescopic channels 18'' / 20'' long , rollers for smooths sliding of drawers, etc as required including taking down old wardrobe, cupboard complete all as specified and as directed. (Note: Overall net size front side including frame will be measured for payment purpose as Sqm and the quoted rate shall deemed to be included for various items as indicated here-in-before)

M & L for washed stone grit plaster on exterior walls in two layers, under layers 12 mm thick cement plaster 1:4 (1 cement :4 coarse sand) following the under layer with scratching tool, applying cement slurry on the under layer @ 3 Kg of cement per square metre, top layer with 15 mm thick cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand:2 coloured marble stone chipping 10mm nominal size) including using Colour pigment & marble powder as required in ground in panels with groove all around as per approved pattern including scrubbing and washing the top layer with wire brushes and water to expose the stone chippings includind forming groove of uniform size 15mm wide and 15mm deep as per approved pattern complete all as specified and as directed.

M&L for repairing of spalled concrete form RCC surfaces (Such as ceiling, beams, columnms, parapets, chajjas etc) in the following stage :- (a) Preparation of existing surface like chipping of unsound weak/ loose concrete with electric hammer or manually including tapping all edges, making squre shoulder of cavities etc not exc 50 mm thickness, removal of debrises complete all sqfd. (b) Applying rust remover cum passivators sikka rust off 100 @ 0.20 Kg/ Sqm/each coat as per manufacture instructions to remove rust from existing reinforcement (make : - Sika or equivalent) (c) Mixing and applying two components epoxy resin concrete bonding coat of sikadur (R&B 42)- @0.40 Kg/ Sqm (Mixing proportion as per manufactures instructions) including preparation of surfaces by chipping and thoroughly cleaning of surfaces complete wherever required over New reinforcement (if required) and as directed by EIC (make: sika or equivalent) Reinforcement shall be measured and paid saprately. (d) Applying a prebached one component polymer modified cementious patch repair mortar N, exc 50 mm in layers of 15 mm thick each of product silka mono Top 122 F as per manufacturer instructions to match the existing surface as in sides and soffits etc of slabs, chajjas, fins, facias, parapets, lintels, columns and beams etc complete including necessary scaffolding, shuttering, necessary chases to brick work or RCC members at any height upto 6 storey building including removing of small trees shrubs etc all as specified and as directed.

S&F in repairs vitreous china wash down water closet pan padestal pattern white, Rimless Bowl for Coupled WC with UF Soft Close Slim Seat Cover, Hinges, Conversion Bend, Fixing Accessories and Accessories Set, Size: 385x645x815 mm, S/P Trap (With Conversion Bend) size (775x350x650mm) with Cistern With Dual Flush Cistern Fitting complete all as specified and directed. (Make Jaquar Model No ONS-WHT-10753NS250UFSM or equivalent in Marc/ Kohler)

S&F in repair urinnal spreader of brass CP for fixing with 15 mm dia pipe complete all specified and directed.

S&F in repair WHB Mixer of brass CP for fixing with 15 mm dia pipe complete all specified and directed. (Make: Jaquar/ Marc/ Kohler)

S&F in repair Chromium plated 2 in 1 Hand Shower (Health Faucet) with 8mm Dia, 1.2 Meter Long Flexible Tube & Wall Hook complete all as specified and directed.Make : Jaquar Cat No ALD- 573 or equivalent Marc/ Kohler)

S & F new vertical Roller venition blinds of special collection self adjusting system of louvers size 100 mm wide (as approved by GE) with aluminum top rail and PVC bottom, weight attached with 100 mm strip complete with chain all as specified and directed by Engr-in-Charge.

K S CONSTRUCTIONS (BID ID -3117245)

M/S GEETANJALI ENTERPRISES (BID ID -3116981)

sunil traders (BID ID -3117483)

M/S SIMRAN CONSTRUCTION CO (BID ID -3110929)

Vishal Traders (BID ID -3117043)

LAXMI GROUP (BID ID -3116958)

R R Associates (BID ID -3116695)

sony engineering works (BID ID -3117566)

VIJAY KUMAR GUPTA (BID ID -3117514)