8355 ADDITION ALTERATION AND SPECIAL REPAIRS OF PUBLIC TOILETS NEAR INDUSTRIAL CANTEEN AND C NO 09 AT NAVAL DOCKYARD MUMBAI ADDITION ALTERATION AND REPAIRS TO FIRST FLOOR OF BUILDING NO P36 RESOURCE PLANNING DIVISION C NO 06 AT NAVAL DOCKYARD MUMBAI

Amount

Taking down cement plaster on brick/ surfaces built in cement mortar including raking out joints, bading for key scrubbing down with water etccomplete all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortat bedding but not backing), removing serviceable tiles to store and rubbish off the premisescomplete all as specified and directed.

Taking down chowkats or frame with shutter (without taking off shutter from frame), n exc 1.5 sqm eachcomplete all as specified and directed.

Taking down chowkats or frame with shutter (without taking off shutter from frame), exc 1.5 sqm but n exc 4 Sqm eachcomplete all as specified and directed.

Dismantling 100/75 mm bore, cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches if required complete all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not other wise specifically provided forcomplete all as specified and directed.

Demolition of brick work or stone /boulder masonry built in cement mortar, including all quoins, arches, pillars, etc complete all as specified and directed.

M & L for brick work with sub class 'B' bricks (old Size) straight or curved on plan exc 6.0 m mean radius and built in CM (1:6)complete all as specified and directed.

M & L for half brick work with sub class 'B' bricks (old Size) straight or curved on plan exc 6.0 m mean radius and built in CM (1:4)complete all as specified and directed.

S&F aluminium window, doors with shutters / frames / partitions made out of extruded powder coasted aluminium sections, with sliding or openable shutters including frame & necessary joining cleats, glazing clip, powder coated aluminium snap beading, screws etc; complete and also including powder coated aluminium fittings such as cobra hinges, butt hinges, tower bolts hooks and eyes, peg syays and handles including connected items, with and including, making good to the disturbed portion with its original specification, complete all as specified and directed. Make: JINDAL/HINDALCO/INDALCO. Note :- (i) The rate quoted shall be inclusive of the cost of neoprene beading, glazing pin. screws and powder coated fittings such as hinges, handles, locking arrangement etc as required, which shall not be measured for arriving the weight. (ii) Item shall be paid as per weight of aluminium section. (iii) The rate shall also be inclusive of complete packing with silicon gel around contacting surfaces of aluminium work, and including matching the existing surface area.

S&F 4mm thick backelite with decoratve choice laminated on both side complete all as specified and directed.

M & L Sheet glass 4 mm thk, ordinary quality and glazing in aluminium beading with screws/ rebates in square exc 0.5 sq.m in each pane complete all as specified and directed.

M&L for Cutting openings, through brick walls for door, window and other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc. to store and rubbish outside of MD land complete all as directed.

S & F 100 mm Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-11 complete all as specified and directed.

S&F Aluminium anodised sliding door bolt 300m long, with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F aluminium anodised Barrel tower bolts of extruded section, length of bolt 200mm complete all as specified and directed.

S&F Extrude aluminium anodised alloy handles, fabricated type 200mm size complete all as specified and directed.

M&L 75mm thick plain cement concrete 1:4:8, type D2 using 40mm graded stone aggregate as in sub base all as specified and directed.

M&L stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, Skirting and dado, aprons etc and removing off the premises and taking the debris outside MD land complete all as specified and as directed.

All as per item No. 22 here in before but as in skirting including 10mm thick rendering in CM 1:4 as backing coat etc complete all as specified and directed.

M&L for complete removal of existing, treatment on wall surfaces and applying two coats of Birla white cement and alkali resistance primer, sanding the surfaces and finally applying two bosts of oil bound distemper complete all as specified and directed.

M & L for granite stone (of any type) slab 20mm thick machine cut in skirting/dado laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing of type and including 10 mm thick backing coat in CM 1:3 complete all as specified.

S&F GI tubing medium grade with all fittings like Tee, bend, elbow etc, 15 mm bore fixed to walls or ceilings with saddles/spacers including taking down existing steel tubing and connection complete all as specified and directed

S&F 20mm bore tubes medium grade galvanised with all fittings and fixed complete to walls and ceiling or laid in floors complete incl the holes in walls and floors shall be made by drilling with drill or jumper and not by dismantling the brick/concrete and made good with CM 1:3 properly including taking down existing steel complete all as specified and directed

S & F white vitreous china squatting pan, 'orissa' pattern, water closet of size 580x440mm with integral foot rest, P/S trap etc, fixed in repair complete all as specified complete all as specified and as directed.

S&F 10 litres capacity PVC low level flushing cistern of approved make including ball valve,syphon set, inlet and outlet pipe, brackets etc. Complete.

S & F white glazed earthen ware vitreous china wash hand basin of size 550x400mm with and including CI brackets, 32mm bore brass CP waste coupling Inlet/ outlet PVC flexible pipe etc complete all as specified and directed.

S&F 15 mm bore dia of pipe, brass chromium plated fancy type bib tap fixed in repairs complete all as specified and directed.

S&F in repairs 15mm size Stop Valves fancy type chromium plated screwed down high pressure with crutch or butterfly handle handle screwed both ends complete all as specified and directed.

S&F in repair 15 mm dia fancy type pillar tap cast copper alloy with capston heads chromium plated screwed down high pressure with or without hot or cold with long screws shanks and fly nuts screwed for iron pipes all as specified and directed.

S&F chromium plated, tubular towel rail 20mm dia, D type, 60 cm long between flange, fixed in repairs complete all as specified and directed.

S&F 110mm dia PVC ( SWR) grade pipes, single socketed in any length with rubber ring joints fixed to walls and laid in flloors/trenches complete all as specified and directed.

S&F 75mm dia PVC ( SWR) grade pipes single socketed in any length with rubber ring joints fixed to walls and laid in flloors/trenches complete all as specified and directed.

S&F 110mm dia PVC ( SWR) grade double T with access doors including fixing clips complete all as specified and directed.

All as per item No 39 above but 75mm dia

M&L PVC SWR floor trap 75mm, plain with grating including setting and jointing with silvent cement complete all as specified and directed.

M&L for rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finishing the surface fair and even complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall, applying two coats of oil emlusion distemper over a coat wall care putty of 3mm thick and alkali primer complete all as specified and directed.

S&F in repairs of vitreous china urinal, half stall type complete including providing andfixing plugs bedding urinal against wall in cement mortar in 1:2 securing urinals to plugswith and including 60 mm brass screws, pointing around urinal back in cement , flush pipes, inlet, outlet etc complete all as specified and directed.

S&F in repairs for vitreous china urinals, bowl type (back or corner wall type,) complete including providing andfixing plugs bedding urinal against wall in cement mortar in 1:2 securing urinals to plugswith and including 60 mm long brass screws, pointing around urinal back in cement , fixing automatic flushing cisternswith brackets, flush pipes, inlet, outlet etc complete all as specified and directed.

S&F 32mm dia PVC waste pipe for WHB and urinals fixed in repairs complete all as specified and directed.

M&L for viterous china urinal partition white of size 310 x 700mm urinal partions slabs, terminating about 40cm above floor, fixed in repairs complete all as specified and directed.

M&L for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified

S&F 0.80mm thickness of in mm plain galvanised mild steel sheeting in ridges, hips, valley gutter, drips ;and straight flashings (length and girth as fixed) with grade of zinc coating 275mm complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified.

M & L for Cleaning of surface of floor by brooming, washing and drying with cloth including removal of oil mats and provision of high density laminated wooden flooring (pergo) 8mm thick fixed in floors / skirting including moulding etc, including dismantling old unserviceable wooden flooring complete all as per manufacturer's instructioncomplete all as specified and as directed. Make:" Pergo / ROSETTA"

S&F for 2nd class hard wood plain, solid, strainght chowkats and frmaes, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

M&L for french polishing on surfaces of any description , width or girth including cleaning and preparing the surface including a coat of wood filler and applying one or more coats on old works complete all as specified and directed.

S&F Roller blinds type made out of standard cloth of approved texture with necessary accessories etc fixed on window openings complete all as specified and directed. Make: D' Décor or equivalent as approved by GE

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. M.S.frame shall be covered with heat moulded design with colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as specified.

Dismantling and taking down the existing old perished PVC insulated Aluminium conductor point wiring of light/fan/ 5/15 Amps socket bell point etc complete with all fittings accessories, such as switches, switch sockets ceiling rose etc from the surface casing/caping and concealed wireing including making good the disturbed surfaces to match with the existing surfaces complete all as specified and directed.

M&L for point wiring complete with proper colour coding using PVC insulated unsheathed multistranded copper conductor cable 1.5 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked, not less than 25mm casing caping with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 1.5sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including modular box with cover plate frame in any module complete for One light/fan/bell point controlled by one 5A switch complete all as specified and directed. Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green (b) Make of wire : Polycab/ Havells/ Gloster

(i) One light point controlled by one switch

(ii) One Fan / Exhaust Fan point controlled by one 5A switch

(iii) One Bell point controlled by one bell push

(iv) One 5 Amps switch socket combination on independent board

(v) One 5 Amps switch socket combination on same board

M&L for point wiring complete with proper colour coding using PVC insulated unsheathed multistranded copper conductor cable 4.0 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked, not less than 25mm casing caping with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 4.0sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including PVC modular box with cover plate complete comprising of 03 Nos 6A sockets and 01 No 15A socket on board complete all as specified and directed. Note: (a) Colour coding shall be folowed as (i) Phase- Red/Blue/Yellow (ii) Neutral - Black (iii) Earth - green (b) Switch socket measured & paid separately.(c) Make of wire : Polycabl/Plaza/Havells/Gloster (d) Make of PVC casing capping :- Precision/ pesto plast / National/Plaza

S & F modular switch 1 way 6A all as specified and directed. Make : Roma/Goldmedal/Legrand

S & F modular Bell Push 6A , 240 Volts all as specified and directed. Make : Roma/Goldmedal/Legrand

S & F modular switch 1 way 16A,1 module all as specified and directed. Make : Roma/Goldmedal/Legrand

S & F modular socket, 6A - 2/3 pin combined 2 modules all as specified and directed by EIC. Make : Roma/Goldmedal/Legrand

S & F modular socket 6/16A,2/3 pin, combined 2 module all as specified and directed. Make : Roma/Goldmedal/Legrand

S & F ceiling rose surface bakelite 65 x 50mm, flush type, 3 terminals complete all as specified and directed. Make : Cona/Anchor/Roma/Goldmedal/Legrand

S&F for modular fan step regulator, 120W - 2 modular all as specified and directed. Make : Roma/Goldmedal/Legrand

S&F Bell DINGDONG type, 240 Volts all as specified and directed. Make : Roma/Goldmedal/Legrand

S&F in replacement 20 Amps Single pole and neutral enclosure with a Two Pin and earth plug and socket complete with one single pole MCB and making connections complete all as directed. Make -Legrand Cat Part No. 5078 14 or equivalent in Siemens /GE/ C&S

S&F in replacement of MCB, FP 63 Amps capacity, C Curve type suitable for 415 volts AC supply with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as directed. Make - Legrand cat No 4087 02 or equivalent in Siemens /GE/ C&S

S&F in replacement of MCB, SPN 63 Amps capacity, C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as directed. Make - Legrand cat No 4086 20 or equivalent in Siemens /GE/ C&S

S&F in replacement of MCB, SPN 40 Amps capacity, C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as directed. Make - Legrand cat No 4086 18 or equivalent in Siemens /GE/ C&S

S&F in replacement of MCB 6 to 32 Amps capacity, C Curve type suitable for 240 volts AC supply, SP with over load and short circuit protection and rupturing capacity not less than 10 KA including making connection complete all as directed. Make - Legrand cat No 4085 87-95 or equivalent in Siemens /GE/ C&S

S&F in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting SPN 12 way, 240 volts with copper bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. Make - Legrand cat No 5076 42 or equivalent in Siemens /GE/ C&S

S&F in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting SPN 8 way, 240 volts with copper bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. Make - Legrand cat No 5076 41 or equivalent in Siemens /GE/ C&S

S&F in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting SPN, 4 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. Make - Legrand cat No 5077 40 or equivalent in Siemens /GE/ C&S

S&F in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 54 & IK 09 protection surface mounting VTPN 4 way, 440 volts with copper bus bar rating 100 Amps for each phase with 2 neutral bar, dust and vermin proof suitable for incorporation of MCB’s etc complete all as directed. Make - Legrand cat part No 5077 50 or equivalent in Siemens /GE/ C&S NOTE FOR ITEM No. 72 to 75 : [i] MCB DBs shall be concealed in wall wherever posible including making good the surface to match with surrounding. [ii] The cost of removing old wooden box and making good of surface i.e. brick work, plastering etc is included in quated rate)

M&L for sub-main wiring with 2 runs of 4.0 sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including non metalic rigid, double lock, ISI marked, not less than 25mm casing caping with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 4.0 sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unservucable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Make of wire : Polycab/ Havells/ Gloster/ Plaza

M&L for sub-main wiring with 2 runs of 6.0 sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and including non metalic rigid, double lock, ISI marked, not less than 25mm casing caping with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 6.0 sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unservucable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed. Make of wire : Polycab/ Havells/ Gloster/ Plaza

S&F MCCB, 415 volts, Four pole of cap 100 Amps, 25 KA, ICS = 100% ICU, with fixed Thermal - Magnetic setting including spreader terminal/ thimble of suitable size and making connections complete all as directed. Make - Legrand cat No 4200 55 or equivalent in siemens/GE / C&S

All as per Srl item No. 78 here in before but MCCB, 415 volts, Four pole of cap 200 Amps, 36 KA Make - Legrand cat No 4202 48 or equivalent in siemens/GE / C&S

S &F in repair Ultra slim edge lit type recess mounting LED 2X2 Luminaire 36 watt and extruded aluminium housing with anti-glare diffuser provides high quality ecomonic energy saving lighting LED Luminaire suitable for 600 x 600 mm modular /POP / Gypsum ceiling complete all as specified and as directed. Make: Crompton cat No LCPL-36-CDL(2X2) / C&S cat No LTCRSLM36WATT2X2 or equivalent Cat part in Surya / Philips

S&F in repirs LED light fitting 20W, 230 V, 4 feet surface monted, indoor decorative aluminium extruded T- 5 LED batten, integrated type etc., complete with all accessories internally pre-wired and including fixing the fitting on wall/ceiling with suitable PVC round block-02 Nos including connecting up with twin core twisted flexible copper conductor cable with suitable size and all as directed. Make- C & S cat part No. LTTB4F20WLED/W (Nakshatra series) or equivalent cat part in Crompton/Wipro /Philips

All as per Srl item No. 81 here in before but 10 Watt 2FT LED tube light fitting integrated Batten Make- C & S cat part No. LTTB210WLED/W(Nakshatra series) or equivalent cat part in Crompton/Wipro /Philips

S&F in repairs Ceiling fan 5 Star Rated (BEE 3.5) 1200 mm sweep heavy duty type complete with and suitable for operation on 230 Volts single phase 50 Hz AC supply and connectin up with and including two core PVC insulated, PVC sheathed copper conductor flexible cable 24/ 0.2 mm including fixing and making connection and fixed by completed all as specified and directed. Make: Havells/CG/ khaitan

S & F exhaust fan of Sweep 300 mm , 1400 RPM, heavy duty type complete with self closing MS louvers, mounted in suitable opening arrangement and suitable for operation on 230 Volts single phase 50 Hz AC supply and connectin up with and including two core PVC insulated, PVC sheathed copper conductor flexible cable 24/ 0.2 mm including fixing and making connection and fixed by using 4 Nos 200 mm long 12 mm dia bolts, nuts and washers and grouted in wall in CM 1:3 completed all as specified and directed. Make: Havells/CG/ khaitan NOTE FOR ITEM No. 83 to 84 : [i] Making good the surface to match with surrounding. [ii] The cost of removing old BER ceilling fan and exhaust fan is included in quated rate)

Supply and lay in repair cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 3½ core. laid in duct / along pole/wall etc including making connection complete all as directed. Note : 1. The cost of Al thimbles/lugs and cable gland etc is incl in quoted rate and no extra payment will be made for it. Make : Ploycab/Havells/Gloster

All as per Srl item No. 85 here in before but conductor of size 6sq mm 2 core

S & F in repair Sheet Metal one way enclosures suitable for holding MCCB 160 to 250 Amps, prewired type, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IK 08 protection surface mounting, dust and vermin proof complete all as directed. Make - Legrand cat No 5078 02 or equivalent in Siemens /GE/ C&S

RAJU ENTERPRISES

SACHINENTERPRISES

BOB ENTERPRISES