ADDN ALTN OF OTM ACCN AT MD LINES HYDERABAD

Amount

B/R ITEMS

Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings etc complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, etc complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc completed all as specified.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded and pointed in any mortar, etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises all as specified and directed.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level), cement concrete ( un reinforced), etc complete all as spfd and directed.

Dismantling single layer mangalore pattern or similar tiles in roofing all as specified and directed.

Dismantling Battens for tiles, shingles etc, of any size including tilting fillets, spaced exc 15 cm, etc complete all as specified and directed.

Demolition of Cement Concrete (Un reinforced) of any description and in any position not otherwise specifically provided for all as specified and directed.

Labour only Erection and fixing for Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, etc complete all as specified and directed. “Note: Material dismantled from item No.2 above shall be utilized”

Supply and fix rolled mild steel sections as in roof trusses, (framed), trussed purlins, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat section) including distance pieces, cleats confirming to Fe-410-W (grade E-250 quality 'A') complete all as specified and as directed.

Material and Labour for preparation of new steel surfaces description over 10 cm in width or girth applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material and Labour for preparation of old steel surfaces description over 10 cm in width or girth applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Material and Labour for Pre painted galvalume aluminum zinc coating, GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply and fix Pre painted galvalume aluminum zinc coating, GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof coverings / cladding to wall, ridges, gutters etc., fixed with self tapping screws complete all as specified and directed.

Material and Labour for for PCC (1:4:8), type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed.

Demolition of brick work or stone masonary, built in cement mortar complete all as specified and directed.

Material and Labour for brick work with fly ash bricks built in CM 1:6 with sub class 'B' bricks straight or curved on plan exc 6 mtr mean radius all as specified and directed.

Material and Labour for brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 all as specified and directed.

Material and Labour for rendering 15 (10+5) mm thick on brick, stone or concrete surfaces in cement mortar 1:4 with using WPC @“200 ml per bag of cement”, surfaces finished even and smooth without using extra cement complete all as specified and directed. (NOTE : - WPC will be measured and paid separately)

Material and Labour for preparation of newly plastered surfaces and applying two coats of cement base paint over a coat of alkali resistant primer on wall surfaces all as specified and directed.

Material and Labour for 15mm thick plastering in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement all as specified and directed.

Material and Labour for 10mm thick plastering in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement.

Material and Labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali-resiatant primer and 1.5 mm thick Birla wall care putty on plastered surrfaces complete all as specified.

Material and Labour for Preparing newly plastered surfaces and apply three coats of white wash on walls complete all as specified and directed.

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil all as specified and directed.

Material and Labour for hardcore using broken stone or boulders nexc 63mm deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface all as specified and directed.

Material and Labour for 75 mm thick PCC 1:4:8 Type D2 (using 40 mm graded stone aggregate) as in sub bases, floors and pavings etc complete all as specified and directed.

Material and Labour for 75 mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified.

Material and Labour for 20-25 mm thick, Machine cut kota stone slab flooring over 20 mm thick cement screed bed in cement mortar 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc completed all as specified and directed.

Material and Labour for 20-25 mm thick Kota stone slab over 15 mm thick rendering in cement mortar 1:3 as in backing coat in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc completed all as specified.

Material and Labour for 50 mm thick PCC 1:2:4 type B1 providing necessary slope (using 20 mm graded stone aggregate) as in roof padding (top) complete all as specifed and directed.

Material and Labour for APP based polymeric membrane minimum weighing 3Kg/sqm and minimum 3 mm thick reinforced with polyster non wove fabric (weight not less than 150 gms/sqm laid over primed surface including bituminious primer conforming to IS -3384 applied @ 0.3 ltrs/sqm by forced application over finished with one coat of aluminium paint @ 100 ml/Sqm, 10 cm overlap fused uniformly by LPG torch flame,with using WPC 200 ml per bag of cement complete incl taking down existing froof treatment and cement plaster of any description, roughing, preparing the surface by cleaning the surface with wire brushing scrubbinbg down with water to receive new treatment all as specified and directed.

Material and Labour for 10mm thick plastering in CM 1:4 with using WPC 200 ml per bag of cement, on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement all as specified and directed. (NOTE : - WPC will be measured and paid separately)

“S & F true or horizontal level 600mmx600mm panels, false ceiling, hot dipped galvanized steel sections exposed surface with precoated capping, main tee of size 24x32mm at every 1200mm c/c and cross tee of size 24x27mm (1200mm & 600mm long) at every 600mm c/c and wall angle of size 19x19mm fixed to perimeter wall, as per manufacturer’s instructions, grid to be suspended at every 1200mm c/c in both directions by using 3mm dia pre-straightened GI wire at every 1200mm c/c internal at the main tee, including 8 to 9mm thick gypsum board of size 600mm x 600mm with rear side aluminum foil and front side PVC lamination, complete all as specified and directed.”

Taking down chowkats or frames with shutters (without taking off shutter from the frames) n exc. 1.5 sqm each and removing to or from store all as specified and directed..

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exc. 1.5 sqm but n exc 4.00 each and removing to or from store all as specified and directed..

Material and Labour for 2nd class hard wood plain straight solid chowkats and frames wrought, framed, rounded, chamfered put together with glue pinned joints all as specified and directed.

Material and Labour for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts of size25x3MM MS flat; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe 290-0 all as specified and directed.

Material and Labour for cement concrete 1:2:4 type B1 using 20mm graded stone aggregate in bed black for hold fasts and coping incl necessary form work weathering slightly rounded or chamfered angles and treating and making good the disturbed portion complete all as specified and directed.

Material and Labour for 2nd class hard wood plain framed factory made panel shutter 35 mm thick (two or three panels) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces, the size of rail & style as per IS 1003 (Part-I) Kiln seasoned and chemically pressure treated all as specified and directed.

Supply and fix 30 mm thick IInd class hard wood glazed and skelton shutters sizes of members as specified in SSR(Part-I) clause 8.24(b), open rebated and prepared to receive glass or gauge (without sash bars ) edges of framing plain, chamfered or rounded, fitted with cut and miterd beads for securing glass or gauge etc. complete all as specified and directed .

Supply and fix 30 mm thick 2nd class hard wood glazed and skeleton shutter of divided into square, with plain chamfered or rounded metred and rebated sash bar any number and framing moulded windows, ventila-tors, etc. are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24 (b) fitted to chowkats complete all as specified and directed.

Supply and fix MS Butt hinges medium weight cold rolled of size 100mm complete all as specified and directed.

Supply and fix MS barrel tower bolts of 200mm long stove enameled black with bright bolt complete all as specified and directed.

Supply and fix MS pressed bow handle, oval type stove enameled black of size 150mm long all as specified and directed.

Supply and fix mild steel sliding door bolts 300mm long plate stove enameled black with bright bolt not less than 12mm dia with and incl a minimum of 6 bolt and nut four on bolt plates and two on staple plate all as specified and directed.

Supply and fix 170mm, ordinary mild steel rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

Supply and fix MS Butt hinges medium weight cold rolled of size 75mm complete all as specified and directed.

Supply and fix MS barrel tower bolts of 150 mm long stove enameled black with bright bolt complete all as specified.

Supply and fix MS pressed bow handle, oval type stove enameled black of size 100mm long all as specified and directed.

Supply and fix mild steel wire type I, gate & shutter, hooks & eyes 150 mm size..

Supply and fix stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of apreture 1.0 mm & fixed with stainless steel wire staples fixed all as specified and directed.

Supply and fix 4mm thick sheet glass ordinary quality and glazing with wooden beads or oil putty in square not exc. 0.50 Sqm in each pane complete all as specified and directed.

Material and labour for preparation of new surfaces of wood or wood based material description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Material and labour for glazed ceramic coloured tiles in vertical surface 350X250X7mm / 450X350X7mm thick set and and jointed in cement slurry and pointed with white or coloured cement to match , laid over and including 10mm thick rendering in cement mortar(1:4) as backing coat, complete all as specified and directed.

Material and labour for for Non skid coloured ceramic tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm, but n exc. 0.18 sqm, in floor etc. set and jointed in net cement slurry & pointed in white or coloured cement to match over 15mm thick Screed bed or bedding layer for laying floor finishes in CM 1:6 all as specified and directed.

Supply and fix in repair Vitreous China squatting pan , water closet "Orissa" pattern size 580 X 440 mm white with intgrel footrest (excluding flushing cistern & flush pipe complete including provision of cement concrete all as specified and directed.

Supply and fix PVC valveless syphonic action type flushing cistern 10 lit capacity low level white with inlet, ball valve, float and handle including brackets and 32mm PVC flush pipe all as specified and directed.

Supply and fix in repair Vitreous china urinal half stall type white with grating and union for discharge pipe(excluding flushing cistern) but including urinal pipe etc complete all as specified and directed.

Supply and fix Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) Complete all as specified and directed.

Supply and fix in repair low density poly ethylene pipes (LDPE) of pressure rating 6 kg/ cm2 Bore of pipes in 32mm,as waste pipe etc completed all as specified and directed.

Supply and fix in repair brass chromium plated shower rose 125mm size fix to iron pipe complete all as specified and directed.

Supply and fix PVC connection 600 mm long 15mm dia with both ends bolt and cup of PVC etc complete all as specified and directed.

Supply and fix in repair stop cock/angular cock 15mm dia cast copper alloy Chromium plated with fancy type,screwed down high pressure screwed for both end for iron pipe or for union and fixed all as specified and directed

Supply and fixed in repair 15 mm bore Bib taps cast copper alloy Chromium plated with fancy type, screwed down, screwed for iron pipe or for brass ferrule all as specified and directed.

Supply and fix Vitreous China wash basin, white, flat back, size 550x400mm including cutting for & pinning in ends of brackets or erracting stand but exclusive of fixing of supply of waste pipe all as specified and directed.

Supply and fix 15 mm dia Pillar taps fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repairs all as specified and directed.

Taking up or down for bore of pipes in 15 mm, steel tubing and connections, all as specified and directed.

Taking up or down for bore of pipes in 20 mm, steel tubing and connections all as specified and directed.

Supply and fix 15mm dia GI tubing medium grade and its connection laid in trenches, floor, wall and ceiling etc all as specified and directed.

Supply and fix 20mm dia GI tubing medium grade and its connection laid in trenches, floor, wall and ceiling etc all as specified and directed.

Supply and fix rotational moulded polythene water storage tank double layered (cylindrical vertical with closed top) hoisted 1000 litre capacity and fixed in position including dismantling water tanks of capacity 1000 ltr all as specified and directed

Supply and fix Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/20 mm - 210 gms/ 25mm-455gms/ 40mm - 690 gms), Bore dia of pipe in 20 mm, etc complete all as specifed and directed.

Supply and fix in repair Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed 20mm bore complete all as specified and as directed.

Supply and fix 110 mm bore PVC (SWR) pipe single socketed,in any length with rubber ring joints, laid in trenches or in floors all as specified and directed.

Supply and fix PVC (SWR) bend any radius of bore 110mm all as specified and directed.

Supply and fix PVC (SWR) single T junction equal or unequal with access door of bore 110mm all as specified and directed.

Supply and fix PVC (SWR) vent cowl of bore 110mm all as specified and directed.

Supply and fix 110mm PVC (SWR) pipe fixed to wall complete with necessary stack clamp complete all as specified and directed.

Material and Labour cast iron Nahani trap 100 mm outlet all as specified and directed.

Material and Labour solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as per specification and drawing all as specified and directed

Supply and fix factory made solid PVC moulded door shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, fixing in frame all as specified and directed.

Supply and fix Butt hinges extruded aluminum alloy with galvanized mild steel pin anodized 100mm type B21 all as specified and directed

Supply and fix Aluminium anodized tower bolt of extruded section 150 mm all as specified and directed

Supply and fix Aluminium handle cast type 150mm size all as specified and directed

Material and Labour for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 40 mm thickness, M-20 Grade, with gery cement and no pigment set and jointed as per manufacturers instructions, laid over and including 50mm thick M sand cushioning, including dismantlig the existing stone slabs/tiles of any description or thickness etc complete all as specified and directed.

Supply only integral water proofing compound

Removing excavated soils n exc 50 m and depositing at a level n exc 1.5 m all as specified and directed.

Supply and fix MS 25 mm dia Drapery curtain rods powder coated decorative type complete all as specified and directed.

Supply and fix MS fancy powder coated brackets for 25 mm dia drapery curtain rods all as specified and directed.

Material and Labour for Granite (of any type) work (table rubbed and polished) 20 mm thick in steps, jambs, pillars, window-cills, cooking platforms,over 15 mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, etc complete all as specified and directed.

E/M PORTIONS

Taking down carefully existing point wiring of any description for (light, fan ,sockets bells etc) complete including fittings such as sunken boxes, switches, sockets, ceiling rose, lamp holders, brackets ,fittings, pendants, fan regulartors etc and making good the disturbed surface of walls, floors etc. all as specified and directed.

Taking down existing sub main wiring /Service wire of any description and size including earth wire, batten, conduits and making good the disturbed surfaces of walls, floors etc., all as specified and directed.

Material and Labour for Point wiring for one light point/fan point/bell point controlled by one switch with 1.5 sqmm multistrand copper conductor cable PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 1.50 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable ( green colour) as earth lead in and including PVC rigid conduit with all fittings for concealed type on stone / brick, masonary walls, roof etc including new CI/MS sunken box of required size and all as directed by Engineer-in-Charge & 3 mm thick plastic laminated sheet for housing switches sockets, regulators etc. including cutting/running chases, pinning in and making good the disturbed surfaces to match with the existing specification, complete all as specified and directed.

All as per Item No.98 above but One 3 pin 5/6 Amps switch socket outlet on independent board complete all as specified and directed.

All as per Item No.98 but One 3 pin 5/6 Amps switch socket outlet on same board complete all as specified and directed .

All as per Item No.98 but for One 3 pin 15 / 16 Amps switch socket outlet point on independent board with 2.5 sqmm PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 2.5 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable (green colour) as earth lead complete all as specified and directed .

Material and Labour for point wiring complete all as specified with 1100 volts grade 1.5 sqmm PVC insulated FRLSH unsheathed 1100 volts with multistranded copper conductor confirming to IS:694:1990 with ISI marking (for Phase, Neutral and Earth) in and including non metalic PVC rigid conduit medium grade with ISI mark of size 20mm dia with all accessories concealed in wall/ceiling/floor/roof etc, including factory made galvanized steel pressed terminal boxes alongwith suitable modular cover plate with frame for fixing modular switches, sockets, fan regulators etc., of suitable modules and the earth wire to be connected to common earth dolly complete all as specified and directed for the following :-

One light point controlled by one modular switch.

One Exhaust fan point controlled by one modular switch.

One Ceiling fan point controlled by one modular switch.

One three pin modular socket 5/6 amps outlet on independent board.

One three pin modular socket 5/6 amps outlet on same board.

All as per Item No:101 but for One 3 pin 15 / 16 Amps modular switch socket outlet point on independent board with 2.5 sqmm PVC (FRLS) insulated unsheathed copper conductor single core multi stand flexible cable and 2.5 sqmm PVC (FRLS) insulated unsheathed copper conductor single core cable (green colour) as earth lead complete all as specified and directed .

Material and Labour for switch piano flush type single pole one way 5/6 Amps complete all as specified and directed .

Material and Labour for switch socket combination flush type 5/6 Amps Multipurpose 2 in 1, 3 pin/5 pin with porcelain base complete all as specified and directed .

Material and Labour for Switch socket combination 2 in 1 flush type universal 3 pin 5 & 15 Amps complete all as specified and directed .

Material and Labour for lamp holder insulated body with back plate suitable for battern fittings complete all as specified and directed .

Supply and fix Ceiling rose surface bakelite 65 x 50 mm 2/3 terminals complete all as specified and directed.

Material and Labour for Fan Regulator (Rotary step type, Switch/Socket type Dimmer) 230/240V, AC complete all as specified and directed .

Supply and fix Modular switch, single pole, one way, 6 Amps one module complete all as specified and as directed.

Supply and fix Modular 6A 3 pin universal socket outlet, 2 module complete all as specified and as directed.

Supply and fix Modular switch, single pole, one way, 16 Amps one module complete all as specified and as directed.

Supply and fix Modular socket outlet 2-in-1, 6/16 Amps, 2 module complete all as specified and as directed.

Supply and fix modular stepped type electronic fan regulator 220 volts, 100Watt complete all as specified and as directed.

Supply and fix 9 W LED bulb of base B22d with color temp 6500K all as specified and directed.

Supply and fix Sheet metal enclosure MCB distribution board including 200 Amps bus-bar single pole and neutral 240V, 16 Ways, double door including taking down of existing sheet metal enclosure complete all as specified and directed .

Supply and fix Sheet metal enclosure MCB distribution board including 200 Amps bus-bar single pole and neutral 240V, 8 Ways, double door including taking down of existing sheet metal enclosure complete all as specified and directed

Supply and fix Sheet metal enclosure MCB distribution board including 200 Amps bus-bar single pole and neutral 240V, 4 Ways, double door including taking down of existing sheet metal enclosure complete all as specified and directed .

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of SPN and current carrying capacity 40 to 63 AMP, in the MCB DB Complete with connection testing and commissioning all as specified and directed.

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of SPN and current carrying capacity 32 AMP, in the MCB DB Complete with connection testing and commissioning.

Supply and fixing 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning all as specified and directed.

Submain wiring with two single core PVC (FRLS) insulated flexible copper conductor cable of size 6 Sqmm and one single core PVC (FRLS) insulated unsheathed flexible copper conductor cable green colour of size 6.0 Sqmm as earth lead in and including 20 mm PVC conduit medium grade with all fittings suitable for concealed type and making good the disturbed wall surfaces to match with existing specification complete with all as specified and directed.

Submain wiring with two single core PVC (FRLS) insulated flexible copper conductor cable of size 4 Sqmm and one single core PVC (FRLS) insulated unsheathed flexible copper conductor cable green colour of size 4.0 Sqmm as earth lead in and including PVC conduit medium grade with all fittings suitable for concealed type and making good the disturbed wall surfaces to match with existing specification complete with all as specified and directed.

Supply, fix, test and commissioning of LED street light luminaires, outdoor type 35 Watts with LED drivers , new generation energy saving and environmental friendly long life LED Street light made up of pressure die cast aluminium housing with high power LEDs as lighting source and lens embedded PC cover with IP66 protection and impact resistance of IK07 suitable for operation on AC single phase 220-240 Volt, 50 Hz supply all as per ENDURA CITYLITE PLATINUM PLUS of Havells or equivalent of other specified makes including provision of two single core 4.0Sqmm copper conductor, PVC insulated, 1100 Volts, cable not less than 8 metre long etc., connecting from junction boxes of poles including taking down the old fitting all as specified and as directed .

Supply, fix, test and commissioning of Wall mounted LED batten 20 Watts (1200x108x62mm) in extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver complete with all accessories, prewired with and including 4 feet 20Watts LED tube light, 5700K with minimum 2000 lumens all as per Cat No.ENDURALINEARNEOBS20WLED865SPCWH of Havells or techno-commercially equivalent of other specified makes fixed on surfaces of wall or ceiling and connecting of flexible wire twin core from ceiling rose to fitting drawn through and including flexible conduit etc., complete all as specified and as directed.

Supply, fix, test and commissioning of Wall mounted LED batten 10 Watts (600x108x62mm) in extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver complete with all accessories, prewired with and including 2 feet 10Watts LED tube light, 5700K with minimum 1000 lumens all as per Cat No.ENDURALINEARNEOBS10WLED865SPCWH of Havells or techno-commercially equivalent of other specified makes fixed on surfaces of wall or ceiling and connecting of flexible wire twin core from ceiling rose to fitting drawn through and including flexible conduit etc., complete all as specified and as directed.

Supply and fix 36W recess mounting ultraslim LED flat panel 2'x2' (TVP Model) made of extruded aluminium frame with high efficient LEDs & glare free opal diffuser, IP20 suitable for armstrong/grid ceiling and making connections with twin twisted unsheathed PVC copper cable of suitable size complete all as specified and directed .

Supply and fix bracket made out of 40 mm dia GI pipe, light grade, 1.5m long, bend to shape including clamps, nuts and bolts etc and required electrical connections including taking out old unserviceable brackets of any description all as specified and directed .

Supply, fix, test and commissioning of 10Watts LED decorative Bulk head light fittings, ultra modern, environmental friendly, energy saving, surface mounted oval bulk head edge-lit LED luminaire 10 Watts comprising of high brightness LEDs with minimum 800 lumens, made of pressure die cast aluminium housing, IP65 protection all as per Cat No.LHEOAOP7UZ6W010 of Havells or techno-commercially equivalent of other specified makes complete with all accessories internally prewired including connecting up with and including twin/three core twisted flexible copper conductor cable of suitable size etc., complete all as specified and as directed.

Supply and fixing ceiling fanscomplete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE of Efficiencia Neo of Havells or equivalent of Five star rated with brushless direct current motor (BLDC) all as specified and directed .

Supply, install, testing & commissioning of Exhaust fan, metal body with automatic back shutter louvers 300 mm sweep, 1400 RPM or more, Air Delivery not less than 1850 CMH, single phase, 240 Volts, AC, 50 Hz all as per Ventil Air - DB of Havells or techno-commercially equivalent of other specified makes including cutting hole in to the wall / existing window / ventilator etc., and making good the disturbed surfaces and connecting up complete including provision of cable 3/2 core of suitable size from ceiling rose to fan in flexible hose complete all as specified and as directed. Note :- The unit rate quoted shall be deemed to include the cost of making hole in walls/other surfaces, making good the disturbed surfaces including any framework/cement work/wood work/welding work etc. required for proper fixing of the exhaust fan and matching to the existing surface.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16.0 sq mm 2 core

Excavation in trenches not exceeding 1.5 mtr wide and not exceeding 1.5 mtr depth for foundation, laying of poles in trenches and getting out in hard/dense soil complete all as directed and specified.

Returning, filling including spreading, levelling, watering and well ramming in layers not exceeding 25 cms thick complete all as all as specified and directed.

Removal of surplus soil to a distance no exceeding 50 mtrs and depositing where directed at a lvevel not exceeding 1.5 mtrs above from the starting point complete all as all as specified and directed.

Supply and spread approved dry M sand for cable laying /foundations/Cable duct including watering and consolidation, cushioning of cable laid in trenches complete all as all as specified and directed. Note:- Punned thickness will be measured for payment purpose.

Material and labour for Fly Ash brick protection with common burnt bricks sub class ‘B’ of size 230 x 113 x 75mm for cable protection complete all as directed .

Material and labour for cutting of road, hard standing made of concrete or premix carpet, WBM, soiling and morrum filling including excavation for laying of cable/pipe all as directed and making good the road/hard standing by using all old/new materials and with PCC (1:2:4) etc, required to match with the existing surface complete all as specified and directed.

Material and labour for Earthing complete with galvanized steel with plate electrode 60 cm x 60 cm x 6.3mm thick buried directly in ground (earth kit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level connected to galvanized steel strip 32mm x 6mm dia by means of bolts, nuts and washers of galvanized iron or steel all as shown in electrical plate No 3 of SSR part-I connected to earth test point incl necessary earth work and excavation PCC 1:3:6 type C1 using 20mm graded stone aggregate for earth chamber with SSR Part-II RCC cover 50mm thick 1:2:4 mix type B1, using 8mm dia TMT bars reinforcement @ 140mm c/c both ways, watering funnel with water pipe GI pipe 15mm dia medium grade and protection pipe GI 40 mm dia, light grade all as specified and directed in SSR Part II. Earth strip and protection pipe beyond 7.5m shall be measured and paid separately.

Earthing complete with galvanized steel earth plate electrode 60cmX60cmX6mm thick buried directly in ground (earth pit not less than 2.25 mtr blow ground level) with top edge of the plate not less 1.5 mtrs blow normal ground level connected to galvanized earth lead wire 4mm dia by means of bolts nuts, check nuts and washers of galvanized iron of steel all as shown in electrical plate No 3 connected to Earthing test point incl necessary earth work, excavation PCC 1:3:6 type CI using 20mm graded stone aggregate for earth chamber provn of PCC cover 40mm thick 1:2:4 mm type B1 funnel with water Pipe, GI pipe, 15mm dia medium grade protection pipe as specified including dismantling of existing unserviceable earth pit and necessary excavation and earth work in any type of soil etc, complete all as specified and directed.

Supply, installation, test and commissioning CPRI APPROVED factory fabricated, outdoor type, LT FEEDER PILLAR BOX made out of 3.15mm thick CRCA sheet of size 1M x 0.75M x 0.35M with projected globe roof for rainwater protection dust and vermin proof, double door with bothe side opening including neoprene rubber gasket, suitable for 440 Volt 3 Phase 4 Wire System, including danger plate, earthing strip point and ventilation louvers at rear side, bottom detachable gland plate complete with suitable size zinc cromium plated nuts, bolts and washers etc. and embeded with 50x50x6mm mild steel angle iron frame and 600mm above the normal ground level complete with internal connection with suitable size of cable, cable lugs and cable glands, PCC foundation in cement concrete 1:3:6 (20mm graded stone aggregate) and testing after installation complete all as specified and comprising of the following :- (a) Aluminium busbar 200 amps - 04 Nos, supported with suitable size of heavy duty porcelin stand lock with suitable size of brass nut, bolts and washer with heat shrinkable PVC sleeving. The bar shall be colour coded (red, yellow and blue) for three phases and black for neutral. (b) MCCB 100 Amps, 415 volt, 16 KA breaking capacity 4 pole electromagnetic release duly connected to busbar as incoming - 01 No. Make : Legrand/L&T/C&S/Hagar.

Supply, installation, commissioning of Glass Top Deep Freezer single phase 240 volt, 50 Hz of 320 litre capacity having single door complete all as specified and directed.

UNITED TECHNO PROJECTS PVT LTD

Mavee Syndicate

M/s R.L.PAREEK

Sri Associates

Sri Lakshmi Enterprises

STANDARD AGENCIES

R. Wadhumal and Sons

power links

Sukhdevraj Sharma Engineers & Contractors Pvt Ltd