SPECIAL REPAIRS TO BLDG NO P41 01 TO 05 AT RUPS SHOPPING COMPLEX AND SPECIAL REPAIRS FOR SHIFTING OF THE PIPE LINE PASSING THROUGH 12 HECTARES OF LAND AT LBOW OF AGE BR II AND AGE EM

Amount

Demolition of cement concrete in floors n.exc 15 cm thick in ground floor (below or ground level all as specified

M&L for 75 mm thick plain cement concrete type C-1, 1:3:6, (40mm graded stone aggregate)as in plinth protection and sub base of floors , finishing the top surfaces even and smooth W/O using extra cement.

M & L 75mm thick cement concrete type C2 (1:3:6) using (40mmgraded aggr.) as in sub base

M&L for 20mm thick screed bed or bedding layer in CM (1:6) for laying floor finishes.

M&L for 10mm thick heavy duty parking tiles of size 300 x300 mm and pointed in matching colour pigment in floors.

Demoloition of cement concrete of any description and in any situation not otherwise specifically provided for

M&L for PCC 1:4:8 type D2 using 40mm graded agg as in fdn filling and mass concrete.

Demolition of precast block walling built in cement mortor

M&L for PCC 1:3:6 type C2 block masonry with solid blocks, exc 10cm in width and setting in cement mortar 1:4 complete

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing).

Material and labour for 15mm thick screed bed in cement mortar (1:6) for laying floor finish all as specified and directed

M&L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M & L for 10mm thick rendering in CM 1:4 on fair faces of brick work or concrete surfaces finished rough to receive tiles .

M&L for coloured Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match

Dismantling of wall and ceiling boards of any thickness including cover fillets.

M&L providing 4mm thick 'E' board in ceiling with galvanised iron snap frame of 'T' Section 24x38x0.70mm wall/cleat angle 25x25x0.35mm thick and hanging with 4mm GI wire all fixed arrangement will be done as per manfraxture instruction including two coat of oil bound distemper and one coat of white wash complete all as directed

Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (Without taking off shutters from the frame)

S&F powder coated aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, locking etc. complete all as specified

S&F Powder coated aluminium frame for doors,windows, ventilators and partitions (Fixed portions) with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F powder coated anodised aluminium door/window shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified

S&F 5mm thick sheet glass ordinary quality and glazing with oil putty or wooden beading in squares exceeding 0.5 Sq. M in each pane.

S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing

Taking down Chowkats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frames)

Supply and fix 100mm long MS butt hinge medium weight cold rolled.

Supply and fix aluminium anodized barrel tower bolt 150mm long extruded section.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy.

S&F MS window guard bars, window frames,Lor T section supports for shelves etc and similar articles confirming to Fe 290-0 or E-165.

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame

Taking down cement plaster on stone , brick, concrete block wall or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc.

M & L for 15mm thick rendering in cement mortar 1:6 on brick or concrete surfaces finishing the surfaces even & fair.

Material and labour for 10mm thick rendering in cement mortar (1:6) on brick or concrete surfaces finished even & smooth W/O using extra cement.

Material and labour for 5mm thick rendering in cement mortor(1:4) on concrete surfaces of ceiling, finished even and smooth W/O using extra cement.

M&L Preparing new plastered surfaces and applying Two coats of cement base paint over one coat of white wash surfaces of walls

Preparing newly plastered surfaces of ceilings and applying three coats of white wash.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of distemper oil emulsion over a coat of alkali resistant primer including chalk whitening etc all as specified.

M&LPreparation of old white wash surfaces of ceiling and applying one coat of whitewash on ceiling complete all as specified and directed.

Material and labour for washing rubbing down and stopping of distempered and painted surfaces applying two coat of oil bound distemper over 3 mm thick wall care putty on wall all as specified and directed.

Material and labour for washing rubbing down and scrapping of painted surfaces applying two coat of cement base paint over one coat of primer on wall all as specified and directed.

M&L for brass 2 levers mortice lock, vertical type, size 100 mm

M&L for anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer?in-charge

M&L for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr in depth and getting out in hard / dense soil complete all as specified and directed.

Excavation in trenches n.exc 1.5 mtr wide and n.exc 1.5 mtr in depth and getting out in soft/disintegrated rocks complete all as specified and directed.

Removing surplus soil to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and directed.

Returning filling in trenches including spreading, leveling, watering and well ramming in layers n . Exc 25 cm complete all as specified and directed.

S&F GI tubing medium grade, ISI Marked conforming to IS 1239 Part-I 2004, 80mm bore with and including all fittings such as bends, elbows, tees, short length, socket, union, check nuts, nipples etc. fixed and laid in trenches/floor/under culvert/road crossing etc, fixed as in repair including dismentling taking down old unserviceable one complete all as specified and directed. (Note: Exacavation and earhwork shall be measured and paid for separately.)

S&F cast iton air release valve butterfly type, nominal size DN-80mm, strandard type heavy duty suitable for PN-1.6 pressure water pipe line including suitable size joints and jointing material, fixed as in repair including dismentling taking down old unserviceable one complete all as specified and directed. Make - Kirloskar / Leader / Zoloto / L&T (Audco) / NVR

Supply and fixing cast iron Sluice valve PN 1:6 as per IS-14846, body, dome, wedge-CI IS:210, rings bronze IS:318, Spindle-SS IS-6603, Gland Packing gresy jute packing, fasteners-CS, Gasket-Natural rubber, Nominal size DN-80mm, both ends flanged in existing line without damaging to existing pipe line, fixed as in repair including dismentling taking down old unserviceable one complete all as specified and directed by Engineer-in-charge. Note :- Suitable size flanges for existing pipe line, joints and jointing material shall be included under this item. Make : Kirloskar / Leader / Zoloto / L&T (Audco)

Construction of brick masonary pit of size 120 x 120 x 120cm internal size with MS sheet 3mm thick and angle iron frame of size 40x40x6mm duly painted with 2 coats of synthetic enamel paint over a coat of red oxide primer including locking arrangement, lifting handle and including excavation / earth work, PCC in foundation, brick work, plaster complete all as specified and directed.

M&L for PCC (1:3:6) type C1 (using 20 mm graded crushed stone aggregate) as in concrete pedastal for supporting the CI/GI pipes including necessary form work including demolition of existing pedastal complete all as specified and directed.

Taking down copper/aluminium point wiring (light, Bell, fan, socket or power) complete and removing material to store for keeping in safe custody or for taking credit and making good the disturbed surfaces of wall /ceiling so as to match with the existing finishes complete all as specified and as directed.

M&L for Point wiring One light /Fan/Bell point controlled by one switch 6/5 Amp with PVC insulated and unsheathed multistranded FRLS copper conductor single core 1.5 Sqmm (nominal area) cable using approved colour code as per IS drawing in and incl PVC casing and capping (ISI Mark) with all accessories including providing PVC board heavy duty incl providing plastic laminated bakelite sheet top coveralongwith copper earth wire PVC insulated & unsheathed multistranded(FRLS) copper conductor cable of size 1.5 Sqmm as continous earth wire connected to common earth and earth dolly complete all as specified. Make of Cable :- Havells/Polycab/Anchor/Finolex

One 3 pin socket outlet 6/5 Amps controlled by one switch on the same board with other switches.

One 3 pin 6/5 Amp socket outlet controlled by one switch indep board.

M&L Point wiring of Power point contolled by one 15 Amp switch independent with PVC insulated and unsheathed multistranded FRLS copper conductor single core 4.0 Sqmm (nominal area) cable using approved colour code as per IS drawing in and incl PVC casing and capping(ISI Mark) with all accessories including providing PVC board heavy duty incl providing plastic laminated bakelite sheet top cover alongwith copper earth wire PVC insulated & unsheathed multistranded(FRLS) copper conductor cable of size 4.0 Sqmm as continous earth wire connected to common earth and erth dolly complete all as specified and as directed. Make of Cable :- Havells/Polycab/Anchor/Finolex

S&F switch piano flush type (ISI marked), single pole, one way 5 Amp, 240 Volts including taking down unserviceable one complete all as specified & directed. Make : Anchor/Havells (Reo)/Kinjal/Kay

S&F switch socket combination 2 in 1, 3 pin, 6 Amp piano flush type (ISI marked), 240 Volts including taking down unserviceable one complete all as specified & directed. Make : Anchor/Havells (Reo)/Kinjal/Kay

S&F switch socket combination 2 in 1, 3 pin, 16/15 Amp piano flush type (ISI marked), 240 Volts including taking down unserviceable one complete all as specified & directed. Make : Anchor/Havells (Reo)/Kinjal/Kay

S&F ceiling rose, surface bakelite, 65mm x 50mm , two to three terminals including taking down unserviceable one complete all as specified & directed. Make : Anchor/Havells /Kinjal/Kay

S & F Round shaped recess mounted slim fit down lighter having latest edge lit LED techonology environment friendly,18 watt complete with driver and all accessories and including connecting up to ceiling rose with 0.5 sqmm two core copper flexible conductor cable incl dismantling taking down unsv fitting any type complete all as specified and directed.Make :Crompton Greaves Cat Part No LSDMN-18-CDL/WW or equivalent in Philips/Bajaj/Havells.

M&L for surface sub main wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 6.0 sqmm (Nominal area) drawn through in and including PVC casing caping/PVC conduit size with all fittings and accessories alongwith one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLS Copper conductor cable of size 4.0 sqmm as earth lead and connected to earth dolly including taking down unserviceable one and making good to disturbed surfaces complete all as specified and directed. Make of Cable :- Havells/Polycab/Anchor/Finolex NOTE: (a)Two run of cable with one run of earth wire and one run of casing capping/conduit will be measured as one length.

S & F LED Street light fitting 25 Watt new generation energy saving & environmental friendly long life versatile pressure die-cast aluminium IP66 road luminaire with high power LEDs as light source and electronic driver including suitable size of GI pipe fixing arrangement on wall incl dismantling an taking out existing unserviceable one.Make :CG/Havells/Philips

S&F MCB DB CRCA sheet powder coated SPN 4 way double door factory made suitable for incorporating MCB as out going connecting incoming and outgoing cables fixed on suitable size of PVC board incl taking out existing unsv DB of any size and making good disturbed surface to match with existing complete all as specified and as directed. Make : Havells/L&T/ABB/Schneider/Legrand

S&F MCB SPN having braking capacity 10 KA. 35 to 60 Amp, 240 volts C curve including taking down unserviceable complete all as specified and as directed. Make : Havells/L&T/ABB/Schneider/Legrand

S&F MCB single pole having braking capacity 10 KA, 6 to 32 Amps 240 volts including taking down unserviceable complete all as specified and as directed. Make : Havells/L&T/ABB/Schneider/Legrand

Earthing complete with galvanised steel earth electrode plate of size 600x600x6mm thick, buried directly in ground (earth pit nbot less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.50m below notmal ground level, connected to galvanised earth lead wire 4.0mm dia by means of suitable GI nuts/bolts and brazed properly up to main board including earth pit in cement concrete 1:2:4 type B-1, precast RCC cover in 1:2:4 reinforced with expanded metal, with suitable handle, excavation and earth work in any type of soil and including medium grade GI watering pipe 25mm bore with funnel wire mesh and medium grade GI wire protection pipe 25mm bore up to main board complete as shown in electrical plate No 3 of MES schedule Part-I 2009, connected to earthing testing point including taking out existing unsv earthing complete all as specified and testing on completion complete all as specified and as directed. Note:- The units rate including the cost of excavation & earthwork in any type of soil, charcoal & salt in alternate layers, 25mm GI pipe (light grade) for watering 25mm GI protection pipe (light grade) funnel wire mesh PCC chamber in PCC 1:3:6 type C-1 cast iron frame and 40mm thick RCC cover for pit etc & no extra payment will be made.

M/s Paramount Association of India

M/S ACE BUILDERS

M/S TSERING DHONDUP

M/S KHANDU CONSTRUCTION

M/S L.N. TRADERS

M/S N T BROTHERS

DEOGRATIES SEMPER AMA ASSOCIATE