PROVN OF WALL TILE IN WARDS DEPTS OF MH INCLUDING SANITATION UNDER GE MIS MHOW

Amount

Taking down cement plaster on brick or concrete surfaces, parapets including raking out joint, hacking for key, scrubbing down with water etc complete all as specified.

M&L for rendering 10 mm thick in CM ( 1:6 ) on fair faces of wall/ concrete surfaces finished even and fair complete all as specified.

M & L for applying two coats of first quality oil emulsion distember over a coat of primer over a coat of Acrylic/Water Proofing Wall Putty (wherever required) on walls complete all as specified and directed. Note:- Putty shall be measured and paid seperately under Ser Item No. 6

M&L for preparation of old decorated surfaces of wall including brooming , scraping down. Smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks and applying two coats of first quality oil emulsion distemper white/coloured over a coat of Acrylic/Water Proofing Wall Putty (wherever it is required in Patches) all as specified. Note:- Putty shall be measured and paid seperately under Ser Item No. 7)

M&L for preparation of old decorated surfaces of wall including brooming , scraping down. Smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks and applying one coat of first quality oil emulsion distemper all as specified.

M&L for preparation of new plastered surface of wall and and applying 2mm thick Acrylic/Water Proofing Wall Putty in two coats (each coat not less than 1mm) and surface finished even and smooth with sand paper complete all as specified.

M&L for preparing old surface of wall and applying 2mm thick Acrylic/Water Proofing Wall Putty in two coats (each coat not less than 1mm) and surface finished even and smooth with sand paper complete all as specified.

Demolition of cement concrete of any description in ground floors, sub base etc complete.

M&L for PCC (1:2:4) type B-0 using 12.5 mm graded crushed stone aggregate as in sub base, levelling course, etc complete all as specified and as directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tile to store yard and rubbish off the premises complete all as specified.

M&L for Non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exc 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile including 15mm thick screed bed or bedding layer in CM 1: 4 complete all as specified and as directed.

M&L for glazed ceramic coloured tiles(Matt/Gloss Finish) of size not less than 300x250x7 mm thick as in vertical surfaces such as wall, dado etc set and jointed in neat cement slurry and pointed with coloured cement to match with colour of tile over and including 10 mm thick backing coat on fair faces of brick work in CM 1:4 mixed with PD Proof 101 LW (+) of Dr fixit or other equivalent integral water proofing admixture @ 200ml/bag complete all as specified and as directed. Note- (a) Tiling work shall be carried out in stages such as taking down cement plaster, preparing the surface, backing coat mixed with WPC chemical, laying & joining of tile . Each stage of tiling work shall be approved and passed by Engineer-in-charge. (b) Pattern/texture/finish of tile shall be approved by GE.

M&L for glazed ceramic coloured tiles(Matt/Gloss Finish) of size not less than 450x300x7 mm thick as in vertical surfaces such as wall dado etc set and jointed in neat cement slurry and pointed with coloured cement to match with colour of tile over and including 15 mm thick backing coat on fair faces of brick work in CM 1:4 mixed with PD Proof 101 LW (+) of Dr fixit or other equivalent integral water proofing admixture @ 200ml/bag complete all as specified and as directed. Note- (a) Tiling work shall be carried out in stages such as taking down cement plaster, preparing the surface, backing coat mixed with WPC chemical, laying & joining of tile Each stage of tiling work shall be approved and passed by Engineer-in-charge. (b) Pattern/texture/finish of tile shall be as approved by GE.

M&L for glazed ceramic coloured tiles (Matt/Gloss Finish) of size not less than 600x300x10 mm thick as in vertical surfaces such as wall, dado etc set and jointed in neat cement slurry and pointed with coloured cement to match with colour of tile, over and including 15 mm thick backing coat on fair faces of brick work in CM 1:4 mixed with PD Proof 101 LW (+) of Dr fixit or other equivalent integral water proofing admixture @ 200ml/bag complete all as specified and as directed. Note- (a) Tiling work shall be carried out in stages such as taking down cement plaster, preparing the surface, backing coat mixed with WPC chemical, laying & joining of tile. Each stage of tiling work shall be approved and passed by Engineer-in-charge. (b) Pattern/texture/finish of tile shall be as approved by GE.

M&L for applying two coats of Sureseal(by Dr Fixit) or other equivalent as approved by GE on plastered surface of brick/concrete surface all as per Manufacuturer's instruction and as specified and directed by Engineer-in-charge. Note- (a) First coat of sureseal (no dilution) shall be applied and allow it to dry for 24 hours. (b) Second coat of sureseal (no dilution) shall be applied perpendicular to first coat direction and allow it to dry for 24 hours. (c) sureseal shall be applied at rate of 1litre per 4 to 5 sqm.

Supply only Liquid Water proofing compound PIDIPROOF 101 LW+ of Dr FIXIT or other equivalent as approved by GE.

S&F in repair PVC spout pipe of 25mm bore & 45cm length in sunken floor including cutting holes in brick walls built in cement mortar and making good the dismantled portion in PCC 1:2:4, type B1 using 20mm graded stone aggregate and disturbed external wall surface shall be made good as per existing surface finish complete all as specified and directed.

M&L for cutting holes in brick walls built in cement mortar at the starting point of down take soil/waste pipe at any floor, fill the joint of down take pipe & trap with thick cement mortar 1:1 and making good the dismantled portion in PCC 1:2:4, type B1 using 20mm graded stone aggregate and disturbed external wall surface shall be made good as per existing surface finish complete all as specified and directed.

M & L for repairing sunken floor by provide water proofing treatment to sunken floor surfaces of RCC slab by the following specifications and all as specified and directed by Eingineer-in-charge :-(a) Provide PCC 1 : 1.5 : 3 type A0 using 12.5mm graded stone aggregate, in required slope , average thickness 50mm on sunken floor slab mixed with and including integral water proofing compound manufactured by Dr FIXIT or other equivalent as approved and finish the surface even & smooth without using extra cement.(b) Rendering 15mm thick in CM 1:3 mixed with & including integral water proofing compound on sunken floor and sides of (Vertical surface) sunken portion.(c) Preparing surface and applying bituminous primer (conforming to IS-3384-1965) @ 0.40 Kg/Sqm complete. on sunken surfaces of floor & wall and provide necessary connections to soil/waste pipe from WC/ nahani trap etc. (d) Applying one coat of tack coat with Industrial bitumen grade of 85/25 at the rate of 1.2 Kg per Sqm. NOTE:(a) Existing sunken treatement portion shall be removed carefully and quoted rate shall be inclusive of this provision. (b) Only floor area shal be measured for payment .

M&L for preparation of old decorated surfaces of wall by removing existing putty/distemper complete and applying two coats of Smartcare Hydroloc(by Asian) or other equivalent as approved by GE and subsequently applying two coats of Oil Emulsion Distemper over a coat of 2 mm Acrylic/WaterProofing Wall Putty(each Coat not less than 2mm) complete all as specified and directed. Note- (a) First coat of smart care Hydroloc (no dilution) shall be applied and allow it to dry for 6-8 hours. (b) Second coat of smart care Hydroloc (no dilution) shall be applied, Perpendicular to first coat direction and allow it to dry for 6-8 hours. (c) Smart care Hydroloc shall be applied at rate of 1.0 litre per 4 to 5 sqm. (d) Work of smart care Hydroloc treatment shall be executed through expert team of Manufacturer or through authorised applicator of Manufacturer.

M&L for preparation of old decorated surfaces of wall by removing existing putty/distemper completely and applying one coat of Smartcare Hydroloc (by Asian) or other equivalent as approved by GE and subsequently applying two coats of Oil Emulsion Distemper over a coat of 2 mm Acrylic/Water Proofing Wall Putty (each Coat not less than 2mm) complete all as specified as directed. Note- (a) First coat of smart care Hydroloc (no dilution) shall be applied and allow it to dry for 6-8 hours. (b) Second coat of smart care Hydroloc (no dilution) shall be applied, Perpendicular to first coat direction and allow it to dry for 6-8 hours. (c) Smart care Hydroloc shall be applied at rate of 1.0 litre per 4 to 5 sqm. (d) Work of smart care Hydroloc treatment shall be executed through expert team of Manufacturer or through authorised applicator of Manufacturer.

Supply & laying water proofing roof treatment with polymeric standard water proofing membrane, Aqua flex manufactured by M/s Bengal Bitumen, MULTIPLAS STANDARD, manufactured by STP TEXAS Ltd/ Hyperplas manufactured by IWL Ltd having 10 years guarantee for water tightness complete all as specified including removing the existing membrane of any description as under:- (a) Preparation of RCC roof surface and applying one coat of polymeric modified bitumen 85/25 @ 1.2Kg/Sqm over a coat of polymeric primer @ 0.30 Kg/sqm including cleaning surface all as per Manufacturer's instruction complete all as specified. (b) Supply & laying 3 mm thick APP polymeric proofing membrane of 3Kg/Sqm HYPERPLAS STANDARD/ MULTIPLAS STANDARD consisting of 100 micron HMHDPE film centre core including coating the surface with compatible primer and torch application of membrane with 10cm overlaps as required, complete all as specified. (c) Applying Aluminium bituminous paint @0.15 Kg/Sqm over the APP membrane surface. NOTE:- The work of water proofing treatment shall be executed through expert team of Manufacturers or authorised applicator of Manufacturer

S&F in repairs PVC (SWR) pipes 75mm bore single soceted in any length with rubber ring joints laid in trenches or in floors or fixed to walls wih clamps complete all as specified.

S&F in repairs stainless steel grating 100 mm dia complete all as specified.

S&F stack clamp made out of 50 mm x 5 mm flat iron and 16 mm dia round iron stage including bolt, nuts and securing ends of stage to wall or roof complete for 75 mm dia of pipe complete all as specified.

S & F in repair 75 mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified.

S&F in repair 75mm bore PVC (SWR) bends any radius complete all as specified.

S&F in repair PVC floor trap 75mm outlet dia with grating including joints to waste pipe fixed in cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate complete all as specified.

Taking up or down 15mm diasteel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified.

S&F 15mm bore steel tubing medium grade ,galvanized with all fitting such as bend ,elbow, socket,tees,and fixed complete to wall or in ceiling or in floors including cutting threading and making forged bends on pipes MS hooks etc ,complete all as specified.

S&F in repair for 15mm bore bib taps chromium plated with crutch or butterfly handle ,screwed down , screwed for iron pipes or brass ferrule complete all as specified.

S&F in repair fancy type chromium plated 15mm bore two way Bib cock cast copper alloy with crutch or butterfly handle, screwed for iron pipe or brass ferrule etc complete all as specified. Make- Plumber/Essco of jaguar(Economical Range)

S&F in repair CP wall mixer for mixing hot & cold water screwed down for iron pipe 15mm bore complete all as specified. Make - Plumber/Essco of jaguar(Economical Range)

S&F in repair vitreous china wash down water closet pedestal pattern white excluding flushing cistern and flush pipes complete all as specified.

S&F in repairs vitreous China squatting pan, 'Orissa' pattern, size 580x440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap, and to flushing pipe, anti syphonage pipe, etc. comple including making good to floor complete all as specified.

M&L in repairs PVC valve less,syphonic action type flushing cistern,low level ,white with inlet ball valve,float and handle including brackets and connection to pipe and fixing of chain and pull or lever if any complete all as specified. Make - Plumber/Essco of jaguar(Economical Range)

S&F in repair health faucet with flexible pipe of one metre length including wall hook for EWC complete all as specified. Make -Plumber/Essco of jaguar(Economical Range)

ss construction

sunrise enterprises

SATHI ENTERPRISES

Jamna Constructions

ram prashad chotelal batham