Construction of Taluk office building at Melur in Madurai District

Amount

Earth work Excavation for foundation in all soils and sub soils and to full depth as may be directed except rock requiring blasting inclusive of shoring, strutting and baling- out of water wherever necessary, re-filling the sides of foundation with excavated earth in layers of 15cm thick well rammed and compacted, depositing the surplus earth within the compound in places shown by the Departmental Officers with an initial lead of 10 meters and lift of 2 meters lift etc., complete with standard specifications.

Earth work open excavation in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the excavated earth with a lead of 10 mts. within the compound in places shown by the departmental officers and clearing and levelling the site, etc., complete complying with standard specification.

Cement Concrete 1:5:10 (One Cement, Five Crushed stone M-Sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and curing etc. complete complying with standard specification

Supplying and filling with Crushed stone M-Sand in layers of not more than 15 cm thick without consolidation etc. complete complying with standard specification and as directed by the departmental officers.

Refilling with excavated earth other than sand with an initial head load of 100 mts. and depositing the earth as shown by the departmental officers in layers of not more than 15 cm thick well rammed, watered and consolidated etc. complete complying with standard specification

Supplying and filling in foundation, basement, etc with filling stone dust in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation and basement with conveyed earth 5kmmr in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Damp proof course in Cement mortar 1:4 (One Cement and four M-Sand) mixed with water proofing compound confirming to Indian standard as specified by the Departmental Officers at 2% by weight of Cement used etc., complete complying with standard specification.

Supplying and erecting centering for sides and soffits including supports for plain surfaces for reinforced cement concrete work such as grade beams, column footing, plinth beam, staircase steps, pedestals bed block covers etc., using mild steel sheets of size 90mm x 60mm of B.G.10 stiffened with welded mild steel angles of size 25 mm x 25 mm x 3 mm boarding laid over silver oak (or) country wood joists of size 10 cm x 6.5 cm spaced at about 90 cm centre to centre and supported by casuarinas props of 10cm to 13 cm dia spaced at 75 cm centre to centre at suitable intervals etc., complete complying standard specifications.

Supplying and erecting centering for sides and soffits including supports and strutting upto 3.29m high for plain surfaces such as RCC slab, beams, TEE or Ell beams, Lintels staircase beams etc., with all cross bearings using mild steel sheets of size 90mm x 60mm of B.G.10 stiffened with welded mild steel angles of size 25 mm x 25 mm x 3 mm boarding laid over silver oak (or) country wood joists of size 10 cm x 6.5 cm spaced at about 90 cm centre to centre and supported by casuarinas props of 10cm to 13 cm dia spaced at 75 cm centre to centre at suitable interval. etc., complete complying standard specifications.

For plane surfaces such as RCC floor slab, roof slab, beams, lintels, bed blocks, landing slab, waist slab, portico slabs and beams, etc.

For plane surfaces such as rectangular or square RCC columns, sunshades, top and bottom slab of RCC boxing, etc.

For circular columns

Providing and laying in position, Standardised Concrete Mix M -20 Grade in accordance with IS:456-2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325Kg/m3 and maximum, water cement ratio of 0.55, including admixture (Plasticser/super plasticiser) in recommended proportions as per IS:9103 to accelerate) retard seting of concrete, improve workability without impairing strength and durability with about(5cum) 7730 Kg. of 20mm machine crushed stone jelly and with about (3.3 cum) 5156 Kg of 10-12mm machine crushed stone jelly and with about (4.79 cum) 7670Kg of CS sand , but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing etc., and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc,. complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggretates to be used should comply with the with standard specification and as directed by the departmental officers

For Foundation and basement

In Ground floor.

In First floor.

In Second floor.

Supplying, fabricating and placing in position M.S or R.T.S reinforcements grill for RCC works as per the design given including cost of steel and G.I black binding wire etc., complete complying with standard specification. (The contractor will have to make his own arrangements for the supply of MS plain rod / RTS rod and GI binding wire)

Brick work in following Cement Mortar using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.In Cement Mortar 1:5

Foundation and Basement

Ground Floor

Brick work in following Cement Mortar using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction.In Cement Mortar 1:6

In Ground floor

In First floor.

In Second floor.

Brick work in following Cement Mortar using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-3/4" for foundation and basement including curing, etc., complete complying with standard specifiction..In Cement Mortar 1:3

Foundation and Basement

Brick partition walls of 10.80cm thickness using best quality country bricks of size 8-3/4" x 4-1/4" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three Sand) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Ground Floor.

First floor

Cement concrete 1:5:10 (one cement, five Crushed stone M-Sand and ten broken stone) using hard broken granite stone jelly 40mm gauge for flooring including dewatering if found necessary and laid in layers of not more than 15cm thick in the case of foundation etc. complete complying with standard specification

Flooring with Anti skid Self Designed Colour Ceramic Tiles of size 305 x 305 x 6mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three Crushed stone M-Sand) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with colour designed digital printed ceramic tiles of size 300mm x 450mm x 8mm best approved quality tiles set in Cement Mortar 1:2 (One Cement and Two Crushed stone M-sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification ( Non branded) and as directed by the departmental officers.

Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 of 18 / 20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three sand) fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with Cement based Hydraulically pressed Anti skid tiles (pattern design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three Crushed stone M-Sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing in position best approved of ISI quality of 110mm dia PVC rain water down fall pipes having a working pressure of 4 kg/cm2 including cost of necessary PVC shoe, PVC bend, CT gratings of required diameter and special clamps, brass screws, nails etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cost of removable iron grating. The PVC pipe shall be fixed in wall with special type of clamps. Special type of U clamp at the centre of the pipe line shall be fixed in addition to those for more than 3m pipe length complying with standard specification.

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three Crushed stone M-Sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Paving the floor with best quality Double Charged Vitrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three Crushed stone M-Sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Special ceiling plastering and finishing the exposed surface of RCC items of work such as slab, beam, sunshade, staircase waist slab, landing slab etc., with cement mortar 1:3 (one cement and three P-Sand) 10mm thick including hacking the surfaces and providing cement mortar nosing, beading for sunshade, staircase step, landing slab neat and finishing and curing etc., complete.

Plastering with cement mortar 1:5 (one cement and five P-Sand) 12mm thick in all floors are including finishing neatly curing etc., complete complying with standard specification.

Plastering with cement mortar 1:3 (one cement and three P-Sand) 12mm thick mixed with water proofing compound at 2% by weight of cement used in all floors, complying with standard specification.

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two sand and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed by the departmental officers

50 mm thick slab.

Plain Cement Concrete 1:2:4 (one cement, two Crushed stone M-Sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers. a) Foundation and Basement

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between.The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc.complete

Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter.

Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate of 1.6mm thick) of size 100mm x 60mm with a rebate of 30 / 35mm x 15mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel hold fast etc.,

Supplying and fixing door shutters for Medium Density Fibre board of exterior grade, Both side Pre laminated including external lipping with Kiln dried soft wood of 35mm thick conforming to IS 12406 / 1989 with necessary adhesive and C.P. screws, including fixing of aldrops, tower bolts, hinges and lock strike plates, putty, fevical, varnish for T.W. lipping with thinner colouring agent etc., The rate includes cost of materials and cost for aluminium furniture fittings such as 3 nos Alu. hinges 125mm, 1 no Alu. aldrop 250 x 16mm, 1no Alu. tower bolt of 200x12mm and 1 no Alu. tower bolt of 150x12mm, 2 Nos Alu. Handles, 1 no door stopper with rubber bush incase of Single leaf door inclusive of labour charges for fixing in position etc., complete. All Aluminium furniture fittings are to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1968 for anodic film thickness of not less than 15 microns, The rate is inclusive cost of fevical and fixing charges, transportation, loading, unloading and all other incidential charges, handling charges etc., complete complying with standard specification.

Single leaf shutter

Double leaves shutter

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x4`0x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat M-Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete.

Single leaf

Supplying and fixing PVC sliding door with Solid PVC door shutters using 19 Gauge 19mm MS square tubes for styles and outer frames, 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm, with suitable rabate for housing the shutter including slidng arrangements. 0.90x2.10m

Supplying and fixing in position of ornamental Teakwood main entrance door of size 2.40x2.40m with the following specification.The outer frame shall be made out of Teak wood scantlings of size175x125mm and shutter Vertical & Horizontal frames made out of Teakwood scantlings of size 175x50mm.TW planks of 25mm thick is fixed as panel in the shutters.Carving works shall be made in the shutter as per the design given by the departmental officers.The side portion of the door is to be provided with fixed glazing arrangements with necessary protection grill arrangements by TW frame of size 175x25mm.Plain glass of 5.50mm thick with grill work shall be fixed in the main door for fixed glazing arrangements.8Nos. Brass hinges of size 150x30mm, 2Nos. of Tower bolt of 400mm long & 12mm dia and 2No. of 300mm long 16mm dia brass Aldrops and 2Nos. of Ornamental brass handles and 2Nos. of door stoppers have to be fixed in the door shutters.8 lever brass best quality door lock to be fixed on the main door.All wooden surface have to be finished with two coats of Lac polish as directed by the departmental officers.The rate is inclusive of wrought and putup for TW scantlings,shutters,glass etc.,Carving works,conveyence charges and cost of all brass fittings etc., complete.

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish 1/3rd fixed glazing 2/3rd prelaminated board of Aluminium partition. The outer frames Outer frame: 63.50x38x3mm@ 1.72 kg/m,Centre mullions: 63.50x38x3mm@ 1.55 kg/m,Alu. Clips: 17.27x17.15x1.50mm @ 0.175kg/mg/m for intermediate vertical mullion 90cm c/c. Horizontal mullion at 1.00m 2.10m covered with 5.5mm thick plain glass with neccessary aluminium clips of size 17.27x17.15 x1.50mm @ 0.176kg/m and with required rubber beading etc., including necessary dismantling holes in RCC column,masonry wherever in necessary with power drills to the extent required and made good the damaged portion in good condition after fixing as directed by the departmental officers. All the aluminium sections should be anodised not less than 15 microns as ISI specification1868/1962 / and should be gotapproved by Executive Engineer before use.

Fabricating Supplying and fixing in position of Aluminium anodised natural colour matt finish of single leaf door with half panelled with 12mm thick both side laminated particle board at bottom and half glazed using 5.50mm thick Plain glass at top.B3538and Shutter frame made of section Vertical & Top rail: 50x44.45x2.50mm @ 1.292 kg/m ,Bottom rail: 100 x44.45 x 2.50mm@ 1.974 kg/m, Lock rail : 50x44.45x2.5mm @ 1.292 kg/m, Alu Clips: 17.15x17.27x1.50mm @ 0.176 kg/m,Alu. Handle: 100x30mm @ 0.988 Kg/m and necessary accessories such as aluminium clips, rubber beading, PVC felt, handle for a length of shutter (both sides), locking arrangements, furniture fittings such as aluminium tower bolts-250x12mm - 1 No., aluminium tower bolt 200x12mm - 1No., aluminium Hydraulic door closer - 1No ., lock-1No.,Door stopper with rubber bush including cost of materials labour charges and power consumption charges required for fabrication including chipping, dismantling and making hole to the required extent in RCC column, beams, masonry with power drill wherever necessary and redoing the damaged portion to the original condition after fixing etc., complete. All the Alu. Section are to be anodised with matt finish under electricaly controlled conditions in accordance with IS 1868/1962 for an average anatic film thickness of 15 microns etc., complete.Aluminium sections,and furniture fittings shall be got approved by the Executive Engineer incharge.

Supplying, fabricating, erecting and fixing Hilux (or) Equivalent Board False Ceiling upto a ceiling height of 4.5m from floor level. Using Hilux Board Plain Sheets (10mm thick)

Supplying and fixing mild steel iron grill for windows ventilators and grill gate MS ladder etc., including one coat of red oxide primer using M.S.angle of size 40x40x6mm and grill using 20x6mm MS flat and necessary hold fast with M.S.angle of size of 40x40x6mm-230mm long spliced at end is to be provided appropriate places for fixing the grill etc complete complying with standard specification. The type design for the grills, gate etc., should be got approved by the departmental officers before execution

Supplying and painting the walls with two coats of Interior Eumulsion paint including cost of one coat of primer using white cement as instructed by the departmental officers including preparation of surface, curing, etc., complete in all floors complying with standard specifications (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use on work).

Supplying and painting the walls with two coats of Exterior Emulsion paint including cost of one coat of primer using white cement as instructed by the departmental officers including preparation of surface, curing, etc., complete in all floors complying with standard specifications (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use on work).

Providing wall putty including labour charges for finishing two coats of wall putty etc., complete in all floors complying with standard specifications

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and color of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete

Providing Anti-Termite Treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 6313 part I to IV in stages to suit the progress of work consist as per the detailed specification as below (Measurements taken for the plinth area for the purpose of payment) including braking of termit mounds, making holes with crow ar, closing the holes after the treatement and including cost of chemicals, labour charges transport and storing etc., complete (The chemical should be got approved by the Executive Engineer before use on works) Stage-1: Spraying anti-termite chemical solution for the foundation before laying concrete in bottom and sides of foundation. Stage-2: Spraying anti-termite chemical solution to the grade beam level, spraying has to done for the grade beam, brick masonry contact with the back fill earth Stage-3: Spraying anti-termite chemical solution on the M-Sand for the flooring before laying the flooring concrete. This treatment has to be carried out on the M-Sand filling by making holes with crow bar to a depth of 60 cms and at 60cms intervals on both. Stage-4: Spraying anti-termite chemical solution alround building outside by making holes through bar before laying plinth protection and the holes to be closed after the treatment.

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). Above Ground Level

Sanitary pipe AGL 110mm dia

Sanitary pipe AGL 75mm dia

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). Below Ground Level

Sanitary pipe BGL 110mm dia

Sanitary pipe BGL 75mm dia

Supplying and fixing in position of the following PVC specials best approved quality conforming to ISS and providing leak proof joints with PVC adhesive etc, including fixing to walls with necessary teak wood plugs screws etc. and giving connections to the PVC pipe dismantling the brick masonry RCC floor or roof slab and redoing the disturbed portion to original conditions etc. complete complying with standard specifications. (The PVC specials should be got approved from the Executive Engineer before use on works).

110mm dia PVC Door bend

75mm dia pvc door bend

110mm dia Y junction

110mm dia plain bend

75mm dia plain bend

75mm dia Y junction

Supplying and filling ISS metal of 40mm size in dispersion trench including stacking for pre measurements around the stoneware pipe or in the leach pit or soak pit to the required thickness as directed by the departmental officers etc.,complete

Supplying and filling ISS metal of 20 mm size in dispersion trench including stacking for pre measurements around the stoneware pipe or in the leach pit or soak pit to the required thickness as directed by the departmental officers etc.,complete

Supplying and fixing in position white glazed earthen ware Oriya Type Indian water closet of size 580mm x 440mm of approved quality with ’p’ or ‘s’ trap with embedding the closet with trap to shape in position with brick jelly concrete 1: 2:5 (One lime and two Crushed stone M-Sand and five brick jelly) using 40mm broken brick jelly and finishing the top to required slope including M-Sand cushion all round the water closet and fixing with necessary teak wood plug, clamps and screws to the portion coming on wall and floor including giving necessary connection the PVC pipe by dismantling masonry floor RCC work and redoing the same to the Original condition with out any leakage with necessary cement plastering 1:3 (One cement, and three M-Sand) 20mm thick complying with standard specification. (water closet with other accessories should be got approved by the Executive Engineer before use on work)

Supplying and fixing in position white glazed European Water Closet of best quality and approved make with 100mm "P" or "S" trap connecting with PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC flushing tank without CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fitting. such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)

Supplying and fixing position PVC Nahani Trap of size 100 x 75 mmwith best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position best Indian make white glazed earthenware wash hand basin of size 550mm x 400mm with necessary cast iron brackets 15mm dia chromium plated pillar tap 32mm dia ‘B’ class GI waste pipe 32mm chromium plated brass waste coupling with rubber plug and chain 15mm dia Nylon connection etc., complete including fixing the wash hand basin in position including cost of teakwood plugs, screws rubber washers, white lead and giving water supply connection, testing for leakage etc., complete complying with standard specification. (The wash hand basin without pedestals should be got approved before use on works.)

Supplying and fixing in position best approved quality beveled edge mirror of size 60 x 45cm shelf type with necessary PVC backing rubber buttons. Brass chromium platted screws, plugs etc., complete complying with standard specification.

Supplying and fixing in position best quality chromium plated Towel rail of 60cm length and 20mm dia with C.P brackets of same material including fixing with necessary T.W plugs, C.P screws and dismantling masonry and redoing the same etc., complete complying with standard specification.

Supplying and fixing in position best approved quality chromium plated soap tray size 150 x 100mm including cost of teakwood plugs chromium plated brass screws etc., complete complying with standard specification

Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.)

Supplying and inserting PVC casing pipe 160mm dia for borewell to with stand the vertical pressure of 6Kg/cm2 without slot including with coupling wherever necessary including cost of cutting and threading and transporting the pipe to work and as directed by the departmental officers etc., including labour charges etc.,complete

Supplying single phase 2 HP submergible pump of approved make conforming to IS 8034 and all cost of materials. The quality and standard of the product should be got approved by the departmental officers before use on works. Necessary Warranty card should be got approved before erection of submergible pump with all accessories.

Supply and fixing of 3 Phase Panel Board including labour charges

Labour charges for erection of submergible pump set in borewell including fixing and jointing submergible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth, valves, erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches, starter, volt metre, ammeter, three pilot (indicating) lamps, capacitor single phasing prevented, water level guard and laying and jointing the cables and twin earthern as per I.E. rules etc., complete and testing the pump set for trial run of 10 days. As directed by the departmental officers complete complying with standard specification.

Supply of 4.00 sqmm three core flat copper cable with wire bounded punched copper conductor insulated and sheeted with PVC.for submersible pump motor with voltage grade upto 1100V confirming to and marked with IS (694-1990) complying with standard specification etc.complete.

Supply and fixing of Nylon rope for borewell and as directed by the departmental officers.

Supplying and fixing of suitable PVC End cap ( With working pressure 6 kg/sq cm)for 6" dia bore well of best quality with ISI mark (The PVC End Cap should be got approved by departmental officers before use on works 160mm dia

Supplying and erecting of 2 H.P mono block motor pump of best approved quality and make with ISI mark monoblock in sump including fixing of suction pipe and foot valve up to a maximum depth of 7m and delivery pipes upto the exterior wall of pump room etc., complete and operating the pumps on trial run for 3 days. (The make and quality of pump set to be got approved by the Executive Engineer before use on works.) 150x20 lpmxm

Supplying laying and jointing CPVC pipes class - V-1MP a with working pressure of 10 kg./cm2 of approved quality and best quality conforming to ISS and with ISI mark of following sizes including cutting threading and fixing CPVC specials but including cost of such specials and fixing into Bore well for suction line, air pipe etc., complete complying with standard specification.

32mm dia pipe

Supplying, laying and jointing CPVC (chlorinated Poly vinyl chloride) pipe( Higher pressure rating with h ig her pipe thickness) Standard Dimension Ratio- 11)of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using SOLVENT OF 118ML (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. External water supply - Below GL

32mm dia pipe

Supplying, laying and jointing CPVC pipes (having working pressure 10 kg. / sq.cm) of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using PVC adhesives (but excluding cost of such specials) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. Above Ground level Above ground level - External

25mm dia pipe

32mm dia pipe

Supplying, laying and jointing CPVC (chlorinated Poly vinyl chloride) pipe( Higher pressure rating with h ig her pipe thickness) Standard Dimension Ratio- 11)of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using SOLVENT OF 118ML (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. Internal water supply- Above GL

25mm dia pipe

Supplying of CPVC (Ashirvad /Astral or equilvalent) Specials of approved quality and good variety conforming to ASTM D-2846standard etc., complete complying with standard specification. (The CPVC specials should be got approved by the Executive Engineer concerned before use on works.)

Elbow

32 mm Dia

25 mm Dia

32 mm Dia

25 mm Dia

Reducer

32 x 25 mm Dia Reducer

25 x 20 mm dia Reducer

20 x 15 mm dia Reducer

CPVC BALL VALVE

Union

Supplying and fixing in position best variety and approved quality heavy type chromium platted (brass) 15mm diameter screw down tap including cost for cutting and threading of the galvanized iron pipes cotton thread shellac etc., complete complying with standard specification.

Supplying and fixing PVC water tank of approved by quality conforming to ISI specification 1000 litres capacity having suitable cover, bolt including cost of tab, taxes, transportation to work spot, fixing in position a place as shown and directed by the departmental officers including conducting required water test complete complying with standard specification.

Supplying and fixing fine polished cuddapah slab of following thickness for cup-board arrangements including laying to correct alignment with necessary cement mortar and black powder etc, complete complying with standard specification and as direct by the departmental officers38 / 40mm thick

Providing Cup-board Shutter using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be got approved from the Executive Engineer befoe use on work.

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Manufacturing, supplying and fixing in positon of RCC Jally of 5cm thick in cement concrete 1:2:4 using 20mm machine crushed stone jelly (excluding cost of reinforcement steel) including cost of mould, finishing, curing, lifting, fixing in position etc., complete complying with standard specification and as directed by the departmental officers

Manufacturing, supplying and fixing in position plain cement concrete precast pavement slab of size 450mm x 450mm of 50mm thick in Cement Concrete 1:2:4 (One cement, Two Crushed stone M-Sand and Four jelly) using 20mm HBG stone jelly including cost of moulding charges, casting of slab, finishing, curing, fixing and pointing the slab with CM 1:3 (One Cement and Three M-Sand) to full depth of slab etc., complete complying with standard specification and as directed

Supplying and fixing best approved best quality Stainless steel Health Facet with Stop coak of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The Health facet should be got approved by Executive Engineer before use on works).

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact.

250 litres

50 litres

Supplying and Fixing of Aluminium Dye Cast Letters of approved size and colour. The colour treatment process is achieved with MRF colour coat and then the processed coloured layer is set into the kiln for the heat treatment process for the following sizes. Aluminium Dye Cast Letters 9" size

Supply and fixing of Water CO2 Stored Pressure Type 9 litres capacity Fire Extinguisher as per new IS 15683 complete with control valve, gun metal cap, pressure gauge, operation sticker, discharges hose, wall mounting bracket, safety clip, etc., as directed by Departmental Officers.

Manufacturing,supplying and fixing of computer table to a height of 75cm and 75cm width using 19mm thick black board for section including providing leg panels at spacing not more than 1m and a sliding board of 35cm width is provided to accommodate key board including fitting the top rest etc. The edges of the table is finished with teakwood lipping which are polished. The other commercial portions are finished neatly etc. The cost includes cost of Labour charges,transport erection and all other incidental charges etc.,complete.

Supply of plastic moulded chair etc complete complying with standard specification and as directed by the departmental officers.

Farbrication & Supplying of steel record rack of size 0.90 x 0.45 x 2.10m with 4 compartments with 4 nos of vertical legs of 40x40mm M.S. Sloted angles and shelf sheet with 18GCR sheet size1.20x0.45m fold sheet the four side with 1 no stiffner plate at bottom necessary slot in the panels holes are made for joints the racks of 6 panels are provide for each rack. All the joints are fixed with bolt & nuts arrangements with necessary connection plate if necessary the bottom of legs are provide with flat bottom piece for stability. The steel racks are painted with 2 coats of paint over priming cost as directed by the departmental officers . The rate inclusive cost of all material ,taxes, transporation and other incidental charges etc. complete complying with standard specification (RACK 5 STEPS)

Suplying of Airport Model Chair unit of 1800mm length. The unit have three nos of chair size of 450mm x 450mm made with pre perforated sheet and coloured by powder coated with stainless steel hand rails and legs connected with bottom axil with size of 80mm x 40mm tubular section.

Incinerator for Ladies Bath room

Supplying, laying and jointing glazed stoneware pipes of following dia of approved best quality with spigot and socket ends (in reverse direction) in dry condition and laid in loose joints (i.e.) without cement and spun yarn, so that the waste water can be drained to the trenches already available, excluding cost of earth work excavation, cost of re-filling with M-Sand / earth, but including laying the pipe in true alignment and gradient and conducting required water supply test for draining with necessary tools and plants, etc., complete complying with standard specifications. 100mm dia stone ware pipe

Supplying and fixing in position 100mm dia stoneware tee of approved best quality and provding leak proof joints with cement, spun yarn, etc., including dismantling the brick work and re-doing the dismantled portion to the original condition, etc., complete complying with standard specifications (The stoneware tee shall be got approved by the Executive Engineer before use on work)

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers

Supplying and fixing of Emblem of 15" size. The cost includes cost of Labour charges,transport and all other incidental charges etc.,complete.

SRI AMMAN CONSTRUCTION

PMA CONSTRUCTIONS

MARUTHU CONSTRUCTIONS