PROVN OF TOILET/ BATHROOM FOR JCOs/OR AT BLDG NO. P-68 AND PROVN OF CHEMICAL EARTHING PITS, 32 AMP POWER TAKE OFF PT, 15 AMPS WALL FITTED PLUG PT WITH WIRING FROM SUPPLY PT AND 6 AMP WALL FITTED PLUG PT WITH WIRING FROM SUP PT UNDER GE 865 EWS AT LE

Amount

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out hard/dense soil complete all as specified and directed.

Excavation over area in Hard/dense soil nexc 1.5m deep and getting out complete all as specified and directed.

Excavation over area in Hard/dense soil exc 1.5m but nexc 3.0m deep and getting out complete all as specified and directed.

M&L for Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for laying UG cavble in trenches on plan and n exc 1.5 m in depth in Hard/ dense soil and getting out complete all as specified and directed.

Returning, filling in, including spreading, levelling,watering and well ramming in layers not exe 25cm in hard/dense soil complete all as specified and directed.

Removing excavated soil material nexc 50m and depositing where directed at a level nexc 1.5 m above the starting poit complete all as specified and directed.

M&l for PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate as mass concrete and filling of foundation complete all as specified and directed.

M&L pre-cast cement concrete(using 20mm graded crushed stone aggregate) 1:3:6 type C-1 as in block masonery with solid block masonery with solid blocks, exc.10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M&L Walling of random rubble stone masonry, uncoursed well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed.

M&L formwork for rough finished concrete surfaces to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and sofits (if any) of foundations and plinth beams and similar works: verticals or to batter complete all as specified and directed.

M&L form work for rough finished concrete surfaces to sides of square, rectangular or polygonal pillars, posts, struts, piers, columns ans stanchions complete all as specified and directed.

M&L form work for rough finished concrete surfaces to sides and soffits of floor or roof beam ,beam haunchings ,girders, bresum-mers, lintles, cantilevers, shelves including supports ,overhanging, etc. also splays between floors and beams,etc complete all as specified and directed.

Form work to sooffits of suspended slabs such as roof, floor slabs, landings etc nexc 200mm thick (horizontal or sloping) complete all as specified and directed.

Form work to edges of concrete flats in floors openings in concrete walls floor and roof and sides of RCC/PCC bands in walls horizontal or sloping and similar work n exc 20 cm wide complete all as specified and directed.

M&L cement concrete Grade M10- Type C0,1:3:6 (using 12.5mm graded crushed stone aggregate) in Damp proof course complete all as specified and directed.

M&L Cement concrete M-25 (using 20 mm graded crushed stone Aggregate) in foundations, inclucing rafts, footings, foundations beams : plinth beams, bases for column, etc, basement slabs , under reamed piles and mass concrete complete all as specified and directed.

M&L Cement concrete M-25 (using 20 mm graded crushed stone Aggregate) in Beams , Cantilievers, bressummers, lintles over 1.5 m span etc complete all as specified and directed.

M&L Cement concrete M-25 (using 20 mm graded crushed stone Aggregate) in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for reinforced cement concrete M-25 (using 20 mm graded crushed stone Aggregate) as in slab supported on walls , beam, and columns in floors, roofs landings , balconies etc complete all as specified and directed.

M&L Mild steel TMT bars10mm dia and over, cut to length, bent to shape required , including cranking , bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per srl item-20 above but 5 mm dia and over upto and including 10mm dia in stirrups , spacers and binders etc complete all as specified and directed.

M&L Hardcore with boken stone of gauge n exc 63 mm, deposited, spread and levelled and layer n exc 15 cm thick, water and rolled /rammed to a true surface complete all as specified and directed.

M & L for 75 mm PCC 1:3:6 type C-2 using 20mm graded crushed stone aggregate as plinth protection finished even and smooth with out using extra cement complete all as specified and directed.

M&L Forming Contraction (Dummy) joints 50 mm deep x 10mm wide for plinth protection & similar work , filled with sealing compound Grade 'A' in plinth protection complete all as specified and directed.

M&L 100mm thick PCC 1:3:6 type C-2 (using 20mm graded crushed stone aggregate) in sub base complete all as specified and directed.

M&L 25 mm thick cement concrete (1:2:4), type B-0, using 12.50 mm graded crushed stone aggregate as in floors including finishing the surface rough for laying finishes complete all as specified and directed.

M&L for Non skid ceramic jointless/joint free coloured tiles 7 to 8 thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortor (1:6) complete all as specified & directed.

M&L for Glazed ceramic coloured tiles in vertical surfaces 450X 350X 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match over 10mm thick CM (1:4) in dado/skirting tiles complete all as specified and directed.

M & L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15 mm thick screed bed in CM 1:4 complete all as specified and directed.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and directed.

S&F 100mm long aluminium anodized, barrel tower bolt of extruded section complete all as specified and directed.

M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and as directed

M&L for 15mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 complete all as specified and as directed

M&L for 5mm thick rendering on ceiling finished even and smooth without using extra cement in cement mortar 1:3 complete all as specified and as directed.

S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd -E 165 complete all as specified and as directed.

Material & labour PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) as in hold fast , bed block and like complete all as specified and as directed.

S & F 2nd class hardwood Plain solid straight chowkhats and frames ,wrought , framed rebated on the solid ,rounded or chamfered put together with glue and pinned at joints complete all as specified and directed.

S&F 35mm thick second class hard wood plain framed panelled shutter (two panels) with lock rail and pannel or 9mm BWP comerical ply or 12mm venered particle board with comerical face venering on both faces. The size of rail and style as per IS-1003 part kilin seasoned complete all as specified and directed.

S&F 2nd class hard wood 30 mm thick glazed and skelton shutters as shutters to windows open rebated and prepared to receive glass gauge etc .(with out sash bars ), edges of framing plain , chamfered or rounded , fitted with cut or mitered beads for securing glass gauge etc ; sizes of members of shutters as spfd in SSR part I, section 8 , clause 8.24 (a) complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty in squares n exe 0.5 sqm each pane complete all as specified and directed.

S&F 150mm size extruded aluminium handles fabricated type, anodised and fixed complete all as specified and directed.

S&F 100mm size medium weight butt hinges complete all as specified and directed.

S&F 300mm mild steel sliding door bolts plate type sove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on stapple plate complete all as specified and directed.

S&F PVC (SWR) 75mm bore Pipe single socketed in any length with rubber ring joints laid in trenches complete all as specified and directed.

S&F PVC (SWR) 110mm bore Pipe single socketed in any length with rubber ring joints laid in trenches complete all as specified and directed.

S & F PVC (SWR) 110MM pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends ISI Marked (any radius) complete all as specified and directed.

S&F PVC (SWR) vent cowl 110mm ISI Marked complete all as specified and directed.

S & F Vitreous china wash down water closet (Pedestal), white (EWC) including Plastic seat of same colour of WC, closed patttern with flat bottom, and cover and Mild steel chromium plated hinging device complete all as specified and directed.

S & F Vitreous China wash basin, white, flat back, size 550 x 400mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S&F PVC (SWR) 'S or P', trap of 110 mm bore complete all as specified and directed.

S & F 750 mm long, 32/ 40 mm dia, PVC flexible Waste pipe for sinks / wash hand basins complete all as specified and directed.

S & F in repairs, 40mm waste coupling of PTMT for sink and wash hand basin (Half or full threaded ) (Minimum Weight 45 grams) complete all as specified and directed.

S&F in repair PVC valve less, syphonic action type flushing cistern of 10 ltr capacity, low level with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F PVC connection 15mm bore with PTMT nuts of length 450mm complete all as specified and directed.

S&F 15mm bore chromium plated Bib tap cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S & F 15 mm bore pillar taps, fancy type Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F fancy type 15 mm bore Stop valves, chromium plated with long shank and cup (Concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S & F fancy type 15 mm bore Angle Stop valves, chromium plated with long shank and cup (Concealed type) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified and directed.

S &F Vitreous China urinals, Half stall type (back or corner wall type),complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F rotational moulded three layered HDPE water storage tanks 1000 ltrs capacity and will be PUF insulated with 75mm thick PUF insulation of density 48kg/Cum (cylindrical vertical type/rectantular loft type closed top) hoisted and fixed in position all as specified and directed by Engr-in-Charge.

M&L applying two coats of cement base paint on newely plastered surfaces including preparation of surfaces complete all as specified and directed.

M&L for preperation of new concrete /plastered surface of any description, applying 3mm thick wall care putty and two coat of distemper oil emulsion over a coat of primer complete all as specified and directed.

S&F Polyproplyene random copolymer (PPR) (SDR 7.4 & SDR 11 UV ) 3 layer pipe with and including SFMC fitting such as bends elbow, tee short length socket union check nuts nipple etc (female and male as required complete of size 32mm outer dia suitable for hot/cold water supply line including testing complete all as per manufactures instructions and as directed by Engineer in charge.

S&F Polyproplyene random copolymer (PPR) (SDR 7.4 & SDR 11 UV ) 3 layer pipe with and including SFMC fitting such as bends elbow, tee short length socket union check nuts nipple etc (female and male as required complete of size 25 mm outer dia suitable for hot/cold water supply line including testing complete all as per manufactures instructions and as directed by Engineer in charge.

S&F PPR 25 MM Gate Valve (Brass insert) as per requirement of the site complete all as specified and directed.

S&F grating doom 100mm dia of CP (Mimimum weight 60 gms) complete all as specified and directed.

S & F CP health faucet ABS with double lock 1.2 mtr CP tube stainless steel flexible hose and wall hook all as specified and as directed.

S&F Towel rail 600mm long Chromium plated (Minimum weight 190 gms) complete all as specified and directed.

M&L for 100 mm thick Cement concrete 1:4:8 type B-2, (using 40mm graded crushed stone aggreate) as in sub -floors, sub- bases, floors and pavings, etc complete all as specified and directed.

M&L for Chequred cement concrete tiles 20cm X 20cm X 20mm thick, set, pointed & jointed in neat cement slurry in floors polished with grey cement & pigments layed over and including 20mm thick cement screed base (1:6) complete all as specified and directed.

M&L RCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate ) in Slabs supported on walls, beams and columns, in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for precast cement concrete 1:2:4 Type B1, (using 20 mm graded crushed stone aggregate) in landings, cover slabs (for manholes etc), chullah hoods, chhajja, water troughs, shelves and similar articles with plain faces, setting in CM 1:6, complete all as specified and as directed.

M&L for Loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified and as directed.

Point wiring complete with 1.5Sq.mm nominal area of copper conductor multi stranded PVC insulated and unsheathed 1100 volts cable drawn through in steel enamelled conceiled conduit with standard accessories such as elbows, tees, junctions etc. and iron moulded terminal box with top cover of including PVC insulated unsheathed solid 1.5Sqmm copper conductor cable as continuous earth lead all as specified and directed for the followings:- (a) One light/exhaust fan point controlled by one way switch complete all as specified and directed.

(b) One switch socket outlet 6 Amps, 230 volts point on Same board complete all as specified and directed.

(c) One switch socket outlet 6 Amps, 230 volts point on independent board complete all as specified and directed.

All as item No 76 above, but using cables 4 Sq mm size complete all as specified and directed.

Supply and fix lamp holder insulated body with back plate complete all as specified and directed.

Supply and fix Switch piano flush button single pole 6 Amps 230 volts one way complete all as specified and directed.

Supply and fix switch Socket combination outlet 5 pin 6 Amps flush type 230 volts complete all as specified and directed.

Supply and fix switch Socket combination outlet multi purpose 5 pin 6/16 Amps 230 volts complete all as specified and directed.

Supply and fix Ceiling rose, surface Bakelite three terminals complete all as specified and directed.

Supply and fix sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 4 Ways 200 Amp rated bush bar complete all as specified and directed.

Supply and fix MCB SPN 40-63 Amp 10 KA C Curve, 240 Volts complete all as specified and directed.

Supply and fix MCB SP 6-32 Amps 10 KA C Curve, 240 Volts 50 HZ complete all as specified and directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250mm complete all as specified and directed.

M&L for Earthing complete with galvanized steel earth plate electrode 600mm x600mmx 6mm thick buried directly in ground. (earth pit not less than 2.25m deep below ground level) with top edge of plate not less than 1.5m below normal ground level, connected to galvanized iron strip 25 x 4 mm by GI watering pipe 15 mm with funnel and wire mesh and 40 mm dia protection pipe earth work etc complete all as shown in electrical plate No 5 of MES plate No. 6complete all as specified and directed by Engr-in-Charge.

Supply and Fixing LED light fitting 1X20 W, 220 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

Supply & Fixing LED light fitting 1X9 W/ 1X 10 W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fixing LED light fitting 35 Watt 230 V AC out door type with high pressure die cast aluminium housing and heat resistant and corrosion resistant including thermal management in multiple optics complete all as specified and directed.

Supply laying and testing cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty 1100 volts grade with stranded aluminium conductor of size 16 sqmm 2 core complete all as specified and directed.

M&L for Sand cushioning to underground cables 8 cm below the cable before laying & 15 cm above the cable after laying, complete all as specified in clause 19.75 of SSR Par-I, complete all as specified and directed by Engr-in-Charge. Note : Punned thickness of 18 CM will be measured and paid.

Supply and laying of factory made, machine pressed, unreinforced, pre-cast concrete cable cover class LV type-2 flate size 250mm x 150mm x 40mm, complete all as specified and directed.

Supply and fix switch Socket outlet 3 pin 5 Amps flush type 230 volts complete all as specified and directed.

Supply, fixing and testing of Chemical earthing with copper earth plate 90cmx60cmx5mm and copper earth strip 32x6mm complete all specified and directed. Note: 1. Chemical earthing to be done by OEM approved by Engr- In- Charge. 2. Earthing test repoart shall be submitted for record. 3. 5% amount of this item shall be reserved from Final Bill for 10 Years as a security deposite for effectiveness of Earthing.

M&L of earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing with Copper strip 32x6mm complete all as specified and directed.

Material and labour for point wiring surface type with two single core 1.5 Sq mm (nominal area) FRLS PVC insulated and unsheathed, multi-stranded, copper conductor cable in and including suitable size PVC casing capping with all fittings and fixing accessories and suitable size PVC box for mounting switches, regulator etc including multi-strand PVC insulated unsheathed stranded copper cable as earth continuity conductor of size 1.5 Sq mm and connecting to light fitting/fans etc complete all as specified and directed for following : - ( colour code to be followed) for followings- For one socket outlet 5 Amps on independent board complete all specified and directed.

All as per Item No 99 but for one socket outlet 15 Amps 3/5 Pin on independent board using cable 2.5 sq mm size with 2.5 Sqmm for earth continuity complete all as specified and directed.

M&L for sub main wiring with 4 runs of FRLS PVC insulated multistrand, copper conductor cable of size 6 Sqmm along with two run of 6 sqmm for earth wire PVC insulated cable 1100 volts multi stranded copper conductor as earth wire in and including PVC casing caping complete all as specified and directed.

Supply and fix sheet metal enclosure for DBs double door when MCB's to be used single pole & neutral 240 Volts 8 Ways 200 Amp rated bush bar complete all as specified and directed.

R B TRADERS