REPAIR/ MAINT TO LEAKAGE, SEEPAGE, JOINERY, PLUMBING AND OTHER B/R WORKS TO CERTAIN OTM BLDG (BI-4, II-1, BI-16, CB-4, T-50) ALONGWITH OTHER CONNECTED BLDGS INSIDE FORT WILLIAM UNDER GE(FW) KOLKATA

Amount

Chipping of unsound /weak concrete materials including cover plaster from RCC structural member i.e. slabs, beams, columns, lintel, chajja, fins, facia etc. of 50 mm average thickness (Any storey/ height of building/ structure) including tapering all edges, making square shoulders of cavities by air or sand blasting etc and cleaning of exposed concrete surface and reinforcement bars, lightly picking materials by air blasting or sand blasting including removal of foreign materials, loose concrete/aggregate etc and disposal of all debris out side of MOD land and complete all as specified and as directed. (NOTE: Measurement shall be considered for the surface area of RCC member)

M&L for applying chloride free rust removing chemical on rusting steel reinforcement bar as per manufacturer's specification and removing all rust from steel reinforcement bar by wire brush & sand/emery paper (after 24 hours of application of rust remover) and cleaning the area thoroughly by water with the help of pressure jet and allowing it to dry and making the reinforcement bar totally rust free (for any storey/ height of building/ structure) complete all as specified and as directed. (Make of Rust removing chemical :- Reebaklens RR of FOSROC or equivalent product other makes specified in tender) (NOTE: Surface area of cleaned steel reinforcement shall be measured for payment)

M&L for introducing new mild steel TMT reinforcement bars for structural connection in RCC beams, columns, lintel and slabs (for any storey/ height of building/ structure) including power drilling holes of appropriate diameters in reinforced or plain cement concrete to a minimum depth of 150mm and up to 200mm including power drilling, fixing the reinforcement in position using epoxy, cleaning of loose dust by blowing air, sealing with epoxy cartridges, plastic nozzles etc as per manufacturer's instructions etc all as specified and directed. (Make of epoxy chemical : Lockfix E75 of FOSROC / Hilti HY 150 or equivalent product other makes specified in tender) (NOTE: Reinforcement bars shall be paid separately)

M&L for preparation of old existing corroded and new introduced reinforcement surface (at any storey/ height of building/ structure) by brush and application of two component epoxy based zinc rich primer, of minimum specific gravity 1.75, adhesive bond strength with steel as 1.50N/mm2, as a protective coating to steel reinforcement bars in concrete with total zinc content in dry film >90% by volume and DFT per coat >50 microns complete all as specified and directed. (Make- Nitozinc primer of FOSROC or equivalent product in other makes specified in tender) (NOTE: Surface area of steel reinforcement shall be measured for payment)

M&L for applying a coat of epoxy bonding agent on existing concrete surfaces, with mixed density 1.48 Kg/litre and adhesive bond strength>2.50 MPs, mixed and applied as per manufacturer's specifications complete all as specified and directed. (Make- Nitobond EP of FOSROC or equivalent product in other makes specified in tender) (NOTE: Measurement shall be considered for the surface area of RCC member.

M&L for applying shrinkage controlled, polymer modified, fibre reinforced cementitious repair mortar, as per manufacturers instructions to get a compressive strength of 35 MPA after 28 days, finishing surfaces even and smooth complete all as specified and directed. (Make- Rendroc SP 40 of FOSROC or equivalent product in other makes specified in tender) (NOTE: Measurement shall be considered for the surface area of RCC member.

M&L for grouting of voids/cracks with high strength epoxy resin grout as per manufacturers instructions complete all as specified and directed. (Make- Conbexta EP 10 of FOSROC or equivalent product in other makes specified in tender) (NOTE: The item shall be executed if any voids/cracks are found during execution/removing of concrete mortar from the surface).

M&L for applying two coats of elastomeric and protective anticarbonation coating, on concrete/masonry surfaces over a coat of silane-siloxane primer as per manufacturer's instructions complete all as specified and directed. (Make- Dekguard E2000 of FOSROC or equivalent product in other makes specified in tender) (NOTE: Measurement shall be considered for the surface area of RCC member.

GENERAL NOTES FOR ITEM NO. 01 TO 08 :- (i) The work shall be got executed through authorised applicator of the chemical manufacturers. Necessary documents to this effect shall be obtained from manufacturer and submitted to the Engineer-in-Charge. (ii) Contractor shall provide additional manpower, resources, preparatory work etc. required for execution of the work as required by the authorised applicator. Quoted rates are deemed to be inclusive of the above aspects. No extra claim shall be admissible during execution of work on this account.

Taking down chowkhats or frames with shutters (w/o taking off shutters from the frames) area not exceeding 1.5 sqm each and removing from the site complete all as specified and directed.

Taking down chowkhats or frames with shutters (w/o taking off shutters from the frames) area exceeding 1.5 sqm and n exceeding 4.00 Sqm each and removing from the site complete all as specified and directed.

Taking down shutters of any description area not exceeding 1.00 sqm each and removing from the site complete all as specified and directed.

Taking down shutters of any description area exceeding 1.00 sqm and not exceeding 2.00 Sqm each and removing from the site complete all as specified and directed.

Taking down shutters of any description area exceeding 2.00 sqm each and removing from the site complete all as specified and directed.

Supply and fixing 2nd class hard wood plain solid straight chowkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F 35mm thick Factory made 2nd class hard wood glazed & skeleton shutters, open rebated and prepared to received glass, gauge etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section 8, clause 8.20(a) complete all as specified and directed.

S&F 30mm thick Factory made 2nd class hard wood glazed & skeleton window, ventilators shutters etc.,, open rebated and prepared to received glass, gauge etc.(with sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section 8, clause 8.20(b) complete all as specified and directed.

S&F 30mm thick Factory made 2nd class hard wood glazed & skeleton window, ventilators shutters etc.,, open rebated and prepared to received glass, gauge etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc, size of members of shutters as specified in SSR Part-I section 8, clause 8.20(b) complete all as specified and directed.

Supply & fixing factory made 35 mm thick 2nd class hard wood panelled shutters (any Nos of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density wood particle board with commercial face veneers, fitted to chowkhats complete all as specified and directed.

S&F 30mm flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Providing and fixing Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S & F PVC solid door frame of size 50 x 47 mm made out of 5 mm thick wood grain printed PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with printed sheet, complete all as per specification & drawing, complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutter with partical board core, 28 to 30mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

Supplying and installing of rectangular & curved/arch uPVC- Fixed windows made out of lead free green profiles having a worldwide presence with a GREENLINE mark with frame dimension of 58mm x 52mm x 33mm for windows with corners fusion welded, fully reinforced with Galvanized steel of 1.2mm . The physical properties of the profiles like Vicat softening temperature, density, tensile strength, hardness, weather ability, impact strength and Modulus of Elasticity should be tested in accordance with ASTM/DIN-ISO standards and the thermal conductivity as per IS standards. The profile manufacturer should be a certified member of IGBC and should have extrusion facility in India and the windows to be assembled and installed by an authorised local fabrication partner . The windows must be installed complete with all kinds of ironmongery in Ist quality (including EPDM gaskets, bridging wedges and glass packers) and with suitable water draining system . Application of Silicon sealant from Inside and Outside with Make: Dowcorning / GE or equivalent. The profiles should be of an international brand having factories in multiple countries and having a warranty of 20 years. The profiles should conform to BSI Quality Management System ISO 9001-2015 and Environmental Management System ISO 14001-2015, with and including necessary scaffolding as required for fixing, complete all as specified and directed. Make: Kommerling or equivalent other approved makes as specified in particular specifications. (Note: The unit rate quoted by contractor excludes cost of glass and powder coated aluminium grill and includes all other connected accessories. Net opening will be measured for payment purpose. Glass and powder coated aluminium grill will be measured and paid separately under respective items)

Supplying and installing of rectangular uPVC fixed windows made out of lead free green profiles having a worldwide presence with a GREENLINE mark with frame dimension of 58mm x 52mm x 33mm for windows with corners fusion welded, fully reinforced with Galvanized steel of 1.2mm . The physical properties of the profiles like Vicat softening temperature, density, tensile strength, hardness, weather ability, impact strength and Modulus of Elasticity should be tested in accordance with ASTM/DIN-ISO standards and the thermal conductivity as per IS standards. The profile manufacturer should be a certified member of IGBC and should have extrusion facility in India and the windows to be assembled and installed by an authorised local fabrication partner . The windows must be installed complete with all kinds of iron mongery in Ist quality (including EPDM gaskets, bridging wedges and glass packers) and with suitable water draining system. Application of Silicon sealant from Inside and Outside of Dowcorning / GE or equivalent. The profiles have a warranty of 20 years. The profiles shall conform to BSI Quality Management System ISO 9001-2015 and Environmental Management System ISO 14001-2015 and also scaffolding if required for fixing is deemed to include in the rate quoted complete all as specified and directed. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net opening will be measured for payment purpose.)

S&F factory made uPVC- Sliding windows/doors having two tracks and two sashes (shutters) with frame dimension of 58mm x 49mm and sash dimension of 61mm x 47mm x 37mm with corners fusion welded, fully reinforced with Galvanized steel of 1.2 mm.The physical properties of the profiles like Vicat softening temperature, density, tensile strength, hardness, weather ability, impact strength and Modulus of Elasticity should be tested in accordance with ASTM/DIN-ISO standards and the thermal conductivity as per IS standards. The profile manufacturer shall have extrusion facility in India and the windows to be assembled and installed by an authorised fabrication partner . The windows must be installed complete with all kinds of iron mongery in Ist quality (including EPDM gaskets, bridging wedges and glass packers) and with suitable water draining system. Application of Silicon sealant from Inside / Outside of Dowcorning / GE or equivalent. The profiles shall have a warranty of 20 years. The profiles shall conform to BSI Quality Management System ISO 9001-2015 and Environmental Management System ISO 14001-2015 and cost of scaffolding if required for fixing shall deemed to be included in the quoted rate complete all as specified and directed. (Note: The unit rate quoted by contractor excludes cost of glass and powder coated aluminium grill and includes all other connected accessories. Net opening will be measured for payment purpose. Glass and powder coated aluminium grill will be measured and paid separately under respective items)

S&F factory made uPVC- Sliding windows/doors having three tracks and three sashes (shutters) with frame dimension of 104mm x 49mm and sash dimension of 61mm x 47mm x 37mm each with middle sash fixed ,fixing of powder coated grill with and including upvc beading of required size, with corners fusion welded, fully reinforced with Galvanized steel of 1.2 mm. The physical properties of the profiles like Vicat softening temperature, density, tensile strength, hardness, weather ability, impact strength and Modulus of Elasticity should be tested in accordance with ASTM/DIN-ISO standards and the thermal conductivity as per IS standards. The profile manufacturer should have extrusion facility in India and the windows to be assembled and installed by an authorised fabrication partner . The windows must be installed complete with all kinds of iron mongery in 1st quality (including EPDM gaskets, bridging wedges and glass packers) and with suitable water draining system. Application of Silicon sealant from Inside and Outside of Dowcorning / GE or equivalent. The profiles having a warranty of 20 years. The profiles shall conform to BSI Quality Management System ISO 9001-2015 and Environmental Management System ISO 14001-2015 and cost of scaffolding if required for fixing shall deemed to be included in the quoted rate complete all as specified and directed. (Note: The unit rate quoted by contractor excludes cost of glass and powder coated aluminium grill and includes all other connected accessories. Net opening will be measured for payment purpose. Glass and powder coated aluminium grill will be measured and paid separately under respective items)

Supplying and installing of uPVC- lower windows with bottom fixed and exhaust made out of lead free green profile having a worldwide presence with a GREELINE mark with frame dimension of 58mm x 49mm and sash dimension of 61mm x 47mm x 37mm with corners fusion welded, fully reinforced with Galvanized steel of 1.2 mm. The physical properties of the profiles like Vicat softening temperature, density, tensile strength, hardness, weather ability, impact strength and Modulus of Elasticity should be tested in accordance with ASTM/DIN-ISO standards and the thermal conductivity as per IS standards. The profile manufacturer shall have extrusion facility in India and the windows to be assembled and installed by an authorised fabrication partner . The windows must be installed complete with all kinds of iron mongery in Ist quality (including EPDM gaskets, bridging wedges and glass packers) and with suitable water draining system. Application of Silicon sealant from Inside / Outside of Dowcorning / GE or equivalent. The profiles shall have a warranty of 20 years. The profiles shall conform to BSI Quality Management System ISO 9001-2015 and Environmental Management System ISO 14001-2015 and cost of scaffolding if required for fixing shall deemed to be included in the quoted rate complete all as specified and directed. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.)

Supplying and installing of uPVC- lower windows with bottom fixed made out of lead free green profile having a worldwide presence with a GREELINE mark with frame dimension of 58mm x 36mm for window with aluminium powder coated frame and glass beads for louvers with corners fusion welded, fully reinforced with Galvanized steel of 1.2 mm.The physical properties of the profiles like Vicat softening temperature, density, tensile strength, hardness, weather ability, impact strength and Modulus of Elasticity should be tested in accordance with ASTM/DIN-ISO standards and the thermal conductivity as per IS standards. The profile manufacturer shall have extrusion facility in India and the windows to be assembled and installed by an authorised fabrication partner . The windows must be installed complete with all kinds of iron mongery in Ist quality (including EPDM gaskets, bridging wedges and glass packers) and with suitable water draining system. Application of Silicon sealant from Inside / Outside of Dowcorning / GE or equivalent. The profiles shall have a warranty of 20 years. The profiles shall conform to BSI Quality Management System ISO 9001-2015 and Environmental Management System ISO 14001-2015 and cost of scaffolding if required for fixing shall deemed to be included in the quoted rate complete all as specified and directed. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose.)

S&F 5mm thick toughened glass as in hinge doors, partitions, windows, automatic doors and similar works including cutting to shape, drilling holes as required complete all as specified and as directed by Engineer-in-Charge.

S&F 12mm thick toughened frosted glass as in hinge doors, partitions, windows, automatic doors and similar works including cutting to shape, drilling holes as required complete all as specified and as directed by Engineer-in-Charge.

S&F Butt Hinges medium weight cold rolled stainless steel 100mm long complete all as specified.

All as per Item No 33 here-in-before, but 75mm long.

S&F aluminum anodised barrel tower bolts of extruded section 150mm long complete all as specified and as directed.

All as per Item No 35 here-in-before, but 200mm long.

S&F Aluminum anodized sliding door bolts of 300mm long with hasp and staple(bolt type) and fixing clips of sheets ,cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F Aluminum anodised bow handle fabricated type extruded section of 125mm long complete all as directed

S&F Aluminum anodised bow handle fabricated type extruded section of 150mm long complete all as directed

S&F stainless steel hinges of 100 mm size, Cat No HG2414 of Make Prayag or equivalent model in other approved makes.

S&F stainless steel handle of size 150mm, Cat No DHL2150 of Make Prayag or equivalent model in other approved makes.

S&F stainless steel handle of size 200mm, Cat No DHL2200 of Make Prayag or equivalent model in other approved makes.

S&F stainless steel tower bolt of size 150mm, Cat No TBR 2150 of Make Prayag or equivalent model in other approved makes.

S&F stainless steel tower bolt of size 200mm, Cat No TBR 2200 of Make Prayag or equivalent model in other approved makes.

S&F stainless steel Aldrop bolt of size 200mm, Cat No LD 1208 of Make Prayag or equivalent model in other approved makes.

S&F stainless steel Aldrop bolt of size 300mm, Cat No LD 1212 of Make Prayag or equivalent model in other approved makes.

S&F 75 mm hasp and staple, mild steel wire type, stove enamelled black, including bolt to hinge plate and fixed with screws complete all as specified.

S&F in repair 150 mm over all length of cover plate of floor door stopper of Brass body and tongue, anodised with hard drawn steel spring fixed in floor.

S&F in repair 150 mm over all length of cover plate of floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor.

M&L for Mild steel small articles such as flat iron 25x3mm thick for hold fasts etc conforming to Fe 410-0, or 310-0, all as specified and as directed.

M&L for PCC (1:2:4) type B1 (using 20mm graded agg) for hold fasts finished to match with the surrounding surfaces including necessary form work, complete all as specified and as directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, all as specified.

Supply & fixed in repairs Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, all as specified.

Supply and fixed in repairs aluminium (die cast) body door closer hydraulically regulated designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified and as directed.

Supply and fixed in repairs double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed.

Taking down easing and adjusting aluminum shutters/partitions including rubber neoprene packing complete of any description n.exc 1 sqm each and refixing in same opening, all as specified and as directed. Note: Replacement of door closer, glass, lock, handle, tower bolt etc shall be measured and paid separately.

All as per items 56, here-in-before, but exc 1 sqm and n.exc 2 sqm each refixing in same opening.

Hacking out old broken glass (any thickness size quality or description) from metal frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones., all as specified and as directed.

M&L for sheet glass 3mm thick figured glass pin head type and glazing with oil putty in square n. exec 0.5 Sqm in each pane complete all as specified and as directed.

M&L for sheet glass 4.80mm thick ordinary quality obscured or frosted on one side and glazing with oil putty in square exec 0.5 Sqm in each pane complete all as specified and as directed.

M&L for sheet glass 4.80mm thick ordinary quality and glazing with oil putty in square exec 0.5 Sqm in each pane complete all as specified and as directed.

M&L solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, all as specified and directed.

S&F in repairs Pre-laminated 9 mm thick particle board interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to frame work complete all as specified.

M&L in repairs 12 mm thick Toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes, handles, fixing accessories as required, complete all as specified.

S&F in repairs 19mm thick plywood, grade BWR, type BB, fixed to existing wooden surfaces with nails. complete all as specified and as directed.

S&F in repairs 12mm thick plywood, grade BWR, type BB, fixed to existing wooden surfaces with nails. complete all as specified and as directed.

M&L 0.9 mm thick decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified.

Supply and fixing Mortice lock vertical type (chrome) 100mm, 6 levers as in repair complete all as specified and as directed. (Make : Godrej Model No- 8194 or equivalent model in other approved makes )

Dismantling wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/ blankets, any thickness including cover fillets complete all as specified.

M&L for snap grid system with powder coated aluminium anodised main 'T' section 36mm x 25mm x 1.40mm cross tee 23.50mm x 23.50mm x 1.40mm thick and powder coated aluminium angle 25mm x 25mm x 1.40mm as on edges/sides, fixed to ceiling with supporting hangar 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. (NOTE: Ceiling board shall be measured separately)

Re-fixing of aluminium snap grid system using serviceable grid sections and ceiling board obtained from taking down of false ceiling including hanging arrangements with supporting hangar 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed. (NOTE: Ceiling board shall be measured separately)

S&F non asbestos fibre cement building board, 4mm thick, fixed to aluminium frame work with screw as in ceiling duly finished with two coats of oil bound distemper over a coat primer complete all as specified.

S&F Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing

S&F 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

Supply and fixing PVC decorative beading of 5mm thick moulded /designed for PVC wall panneling inclusive of fixing complete all as specified and directed.

M&L in repairs tensile fabric of weight 750 gm/m2- ENISO 2286-2, Standard format length-50lm-300lm, tensile strength (warp/weft)- 30/28 daN-DIN 53.363, finish as per formula S2 fluorinated varnish weldable, Solar transmission- 13.5%, etc complete of any design/ pattern as approved by GE/ Engineer-in-Charge.

S&F in repairs 4 to 6 mm thick ACP (Aluminium composite panel) boards, exterior type, coloured and design as per requirement at site, as per the manufacturer instructions, complete all as specified and directed.

Taking down/removing of existing water proofing treatment on roof surfaces and wall surfaces complete, including screed bed, racking out joints, hacking for key scrubbing down with water etc including dismantling of lightening strip and refixing the same in position, and removing rubbish out from MD land, all as directed. (Note :- Dismantling and refixing of the lightening strip is deemed to include in the rate quoted if any).

M&L for brushing neat cement slurry with 2.75 Kg of cement per Sqm on roof complete all as specified and directed.

M&L for cutting Grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 or cement concrete 1:2:4 type-B1 as required complete all as specified and directed.

M&L bituminous gola, with 80/25 bitumen and coarse sand mixture, 1:3 by weight, 8cmx8cm at the junction of roofing to vertical surfaces, all as specified and directed.

M&L for Providing Cement Concrete, type B-0, 1:2:4 (using 12.50 mm graded Stone aggregate), as in roof padding mixed with water proofing compound and the concrete surfaces is to be finished even and fair (without using extra cement) complete all as directed by Engineer - in - charge . (NOTE: WPC Shall be measured & paid superlatively under respective item)

M&L 15 mm thick screed bed in cement mortar 1:3 over roof mixed with water proofing compound as per manufacturer's instruction, finished even and smooth without using extra cement, complete all as specified and directed. (NOTE: WPC Shall be measured & paid superlatively under respective item)

M&L for water proofing treatment on existing cleaned RCC roof with the following specifications and manufacturer's instruction complete all as specified and directed :- (i) Preparing and cleaning of fully dried surfaces as per IS 3067-1966. (ii) Applying bitumen primer conforming to IS:3384-1968 over the cleaned base @ 0.50 litre per sqm. (iii) Providing a layer of 3 mm thick APP modified pre-fabricated five layer, weight not less than 3.6 kg/sqm, black finished reinforced with non-woven polyster matt membrane with butane torch application. Overlap shall be minimum 100 mm on the transverse direction and 75 mm on longitudinal direction. (iv) Applying two coats of bitumen based UV reflective paint with aluminium finish @ 0.20 litre per sqm over APP membrane.

Demolition of Brick work / stone masonry built in cement mortar and removing the debris from MD land complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not other wise provided for.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided for.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar.

Taking down cement plaster of any description on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc.

M&L for brick work with fly ash brick straight or cuved on plan exc 6.0 mtr mean radius built in 1:6 cement mortar complete all as directed.

M&L for brick work with fly ash brick straight or cuved on plan to any radius in half bricks thick walls, built in 1:4 cement mortar complete all as directed.

M&L for cement concrete (1:2:4) type B1, using 20 mm graded stone aggregate, as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and necessary formwork complete all as specified and directed.

Dubbing out average 10mm thick cement plaster 1:4, on irregular face of walls (when specifically ordered in writing), complete all as specified and directed.

M&L rendering 15mm thick on fair faces of brick work/ concrete surfaces in CM 1:6, finished fair & even & smooth without using extra cement & including applying water proofing smart care damp block compound 2K, Make: Asian Paints / Berger Paint or equivalent make specified in the tender, as per manufacturer instructions, including necessary scaffolding in any position, all as specified and directed.

M&L rendering 10 mm thick on fair faces of brick work/ concrete on ceiling surfaces in CM 1:3, finished fair & even & smooth without using extra cement.

M&L rendering 15mm thick on fair faces of brick work/ concrete surfaces in CM 1:4, finished fair & even & smooth without using extra cement & including applying water proofing smart care damp block compound 2K, Make: Asian Paints / Berger Paint or equivalent make specified in the tender, as per manufacturer instructions, including necessary scaffolding in any position, all as specified and directed.

Supply only liquid water proofing compound of Make Pidilite or equivalent, all as specified and directed.

S&F for Framed work such as grills, gratings etc, with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0, and for portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc.all as specified.

M&L for Rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Gde Fe-410-W (Gde-E 250) quality-A, complete all as specified and directed. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete)

M&L mild steel work in tubular trusses including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS-1161:2014 grade St-240 complete all as specified and directed. (NOTE: Quoted rates shall be deemed to include for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete)

Supply and fix 6 mm thick polycarbonate sheeting as in roof covering/cladding to walls, fixed with self tapping screws etc., as in repairs, complete all as specified and directed.

M&L welded steel wire fabric, weight n exc 4 kg per square meter complete , fixed to steel members, all as specified and directed.

Cutting holes in brick walls in cement mortar for inserting holdfast or pipes and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required exc half brick but not exc one brick, etc complete all as specified and directed.

M&L 25mm thick cement concrete type B0, 1:2:4, (using 12.5 mm graded aggregate) as in sub base for floor.

M&L screed bed or bedding layer or mortar 20 mm thick for laying floor finishes in CM 1:4 complete all as specified and directed.

M&L for 18-20 mm thick granite slab of approved quality (table subbed and polished) in steps, jambs, pillars, window cills, cooking platform and like in cement mortar (1:4) including pointing in white cement (1:2) using in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, all as specified as directed.

Providing edge moulding to 18-20mm thickness of granite stone any description of counters vanities etc including machine polishing to edge to give high gloss finish etc complete all as directed.

M&L cement concrete type C2 (1:3:6) using 40 mm graded stone aggregate, 75 mm thick as in plinth protection, laid in alternate bays, finished even and smooth without using extra cement, complete all as specified and directed.

M &L cement concrete Type D2 ,1:5:10 ,Type E2 using 40mm graded stone aggregate as in filling.

M&L for providing two coat of master seal 550 or equivalent to prevent leakage/seepage through sunken floor over prepared surfaces complete all as specified and directed.

M&L polythene film, black 150 micron laid in floors, all as specified and directed.

S&F Vitrified coloured (light shade) Ceramic tiles, double charged, minimum 08 mm thick (square/rectangular) polished, as per approved design, area of each tiles not exc 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and incl screed bed 20 mm thick in cement mortar 1:4 complete all as specified and directed.

All as per item No.114 above, but light shade vitrified tiles in skirting over and incl screed bed 10 mm thick in cement mortar 1:3 complete all as specified and directed.

M&L Vitrified ceramic coloured (dark shade) tiles, double charged, minimum 8 mm thick (square/ rectangular) polished, area of each tiles exc 0.36 sqm but not exc 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade laid over and incl screed bed 15mm thick cement mortar 1:4 complete all as a specified and as directed

ll as per item No. 116 above, but dark coloured double charged vitrified tiles in skirting, fixed over and incl 10mm thick rendering in cement mortar 1:3 complete all as specified and directed.

S&F non-skid ceramic coloured tiles (square/ rectangular), 7 to 8 mm thick, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, set and jointed in neat cement slurry in floors and pointed in white or coloured cement to match the shade of tiles, laid over and including screed bed 15 mm thick in cement mortar 1:6 complete all as specified and directed.

S&F glazed coloured ceramic tiles in vertical surface, as per approved design, size 300 X 450 X 7 mm or 350 X 250 X 7 mm or 300x600x7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles, laid over and incl 10mm thick screed bed in cement mortar 1:3 complete all as specified and directed.

Taking up or down GI Steel Water Tubing including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed for the following size of pipes :-

15mm bore outer dia

20mm bore outer dia

25mm bore outer dia

40mm bore outer dia

Supply, Laying and testing Steel Water Tubing, Galvanised, ‘Medium Grade’ with all Fittings, laid in trenches/floors or fixed on walls/ceilings, in any other Situation, complete as all specified and directed for the following size of pipes :-

15mm bore outer dia

20mm bore outer dia

25mm bore outer dia

40mm bore outer dia

S&F Gun metal gate valve as per IS : 778-84 Class-1 Pressure tested 2.4 Mpa with iron wheel head, screwed both ends for iron pipes or for unions as in repairs, complete as all specified and as directed for the following size of pipes :-

20 mm bore

25 mm bore

Supply, hoisting and fixing rotational moulded polyethylene water storage tank (cylindrical vertical type with closed top) of capacity 1000 Litres, multi-layered (ISI marked), with GI tank nipple & cover, hoisted and fixed in position all as specified in SSR Part-I incl dismantling of existing unsv tank complete all as specified and directed.

All as per item No. 123 here-in-before, but 500 Litre capacity

S&F in repair 25 mm bore Ball brass valves, high pressure, with HDPE float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. (MAKE : PRAYAG, Cat No. B-153 or equivalent model in JEXON / POLYTUF / SHAKTI)

S&F in repair vitreous china floor mounted coupled closet (Pedestal pattern), white, including low level vitreous china valveless symphonic action type flushing cistern with inlet ball valve float, push button, flush pipe incl bracket, P/S trap, PVC white soft close seat cover and connecting fittings complete all as specified and directed. (Make :CERA, Model : CLAIR DELUXE / PARRYWARE, Model: CASCADE NXT / JAQUAR, Model: FONTE / HINDWARE, Model: CONSTELLATION PREMIUM)

S&F in repair vitreous China Squatting pan ‘Orissa’ pattern, size 580 X 440 mm, white, with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, etc and including making good to floor, complete all as specified and directed. (MAKE : CERA, Cat No: S3010109 / HINDWARE, Cat No. 20042 /ASIAN PAINTS, Cat No: WM-32-X / PARRYWARE, Cat No: C0126)

S&F in repair Vitreous China Wash Hand Basin 550mm x 400mm in size, white, Flat Back or Angle Back Type, making good disturbed Surfaces in Cement Mortar 1:3, providing CP waste coupling and PVC waste pipe and connected Items, complete all as specified and directed. (Make of WHB : PARRYWARE, Model: FLAIR / HINDWARE, Model: MARIO / JAQUAR, Model: CONTINENTAL / CERA, Model: CLAIR/ASIAN PAINTS, Model: SIRIUS) (NOTE: Quoted rate shall be deemed to be inclusive of the cost of brackets, waste coupling and waste pipe)

S&F in repair 10 ltrs capacity PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and incl with flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete all as specified and directed. (MAKE : PARRYWARE, Model : Slim line Economy / HINDWARE, Model : Sleek Plus / CERA, Model : Corona / PRAYAG, Model: SMART /ESSCO, Cat No: WHE-WHT-183NL)

S&F for plastic water closet seat cover colour/ white, closed pattern with flat bottom and MS CP or aluminised hinging device as in repair of make Cera/Parryware/Hindware.

S&F in repair vitreous china, wall mounted closet, white incl bracket, trap, PVC soft close seat cover and connecting fittings complete all as specified and directed. (Make : CERA, Model : COMPACT / PARRYWARE, Model: CASCADE NXT / HINDWARE, Model: STUDIO)

S&F in repair Vitreous china, white, full stall urinal flat back with grating and union for discharge pipe (excl flush pipe and flushing cistern and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and Union for discharge pipe complete all as specified and directed. (Make of Urinal : CERA, Model: CAPRIANA / HINDWARE, Model: FLAT BACK LARGE / Jaquar, Cat No: URS-WHT-13261/PARRYWAYR, Model: New Magnum) (NOTE: Waste copupling and waste pipe shall be measured and paid separately)

S&F in repair PVC waste pipe 38/40 mm dia, 800 mm length of Cat No 328 of Make-Prayag or equivalent in Polytuf for urinal.

S&F in repairs PVC connection 450mm long of PTMT 15mm bore of make Cera/Essco/Prayag.

S&F bathroom mirror of size 600x600 mm cat No 553 of Make Prayag or equivalent model in other approved makes.

S&F in repair chromium plated, fancy type soap dish, Cat No T-6902A1 of Make Parryware or equivalent in Jaquar/Hindware.

S&F in repair toilet paper holder with cover of Chromium plated Cat No T-6514A1 of Make Parryware or equivalent in Jaquar/Hindware.

S&F in repair angle valves, fancy type chromium plated of Cat No G4807A1 of Make Parryware or equivalent in Jaquar/Hindware.

S&F in repair PVC waste pipe 32 mm dia, 800 mm length of Cat No 327 of Make-Prayag or equivalent in Polytuf .

S&F corner glass shelf Cat No T-6010A1 of Make Parryware or equivalent in equivalent in Jaquar/Hindware.

S&F in repair health faucet cock brass chromium plated including hose & hook Cat No T-9961A1 of Make Parryware or equivalent in equivalent in Jaquar/Hindware.

S&F brass chromium plated grating of size 102 mm dia with waste hole of cat No FT-04 of Make-Prayag or equivalent in Cera/Essco.

S&F 15mm bore two way bib cock, fancy type chromium plated Cat No G-4834A1 of Make Parryware or equivalent in equivalent in Jaquar/Hindware.

S&F in repair pillar taps fancy type chromium plated swan neck Cat No G4803A1 of Make Parryware or equivalent in equivalent in Jaquar/Hindware.

S&F in repair Bib taps with aerator fancy type chromium plated Cat No G4880A1 of Make Parryware or equivalent in Jaquar/Hindware.

S&F towel rack fancy type chromium plated Cat No T-6008A1 of Make Parryware or equivalent in Jaquar/Hindware.

S&F towel ring fancy type chromium plated Cat No T-6904A1 of Make Parryware or equivalent in Jaquar/Hindware.

S&F in repair 15mm bore auto closing concealed urinal flush valve with wall flange, fancy type chromium plated Cat No PRS-073 of Make Jaquar or equivalent in Parryware.

S&F in repair regular or any connected pattern seat cover white or off white suitable of cascade closet floor or wall mounted with complete arrangement, of Make Parryware or equivalent in Jaquar.

Dismantling of 100mm bore cast iron (sand cast) soil, waste or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required all as specified and directed.

Dismantling of 150mm bore cast iron (sand cast) soil, waste or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required all as specified and directed.

S&F 100 mm bore cast iron (sand cast) soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls complete all as specified.

S&F 150 mm bore cast iron (sand cast) soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls complete all as specified.

S&F 100 mm bore cast iron (sand cast) soil, waste and vent pipes, in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified.

S&F 100 mm dia CI branch pieces complete all as specified.

S&F 100 mm dia CI bend complete all as specified.

S&F 100 mm dia CI branch pieces with ovel access door complete all as specified.

S&F 150 mm dia CI (sand cast) branch, with or without ears, complete all as specified.

S&F 150 mm bore CI (sand cast) bend any radius, diminishing pieces or tapers complete all as specified.

S&F 100 mm dia CI bend with ovel access door complete all as specified.

S&F 100 mm dia CI sanitary connection socket to fit WC outlet complete all as specified.

S&F for cast iron floor trap/nahani trap with grating including jointing to waste pipes in cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate ,100mm dia outlet complete all as specified .

S&F stack clamps out of 50 mm by 5 mm flat iron and 16 mm dia round iron stay, including bolts and nuts and securing ends of stays to wall or roof of 100 mm dia of pipes.

All as per item No 163 above, but 150 mm dia of pipes.

M&L for seven stage cleaning and sterilization of inside the PCC/RCC water storage tanks capacity not exceeding 500 ltr of any description and in any position comprising following seven stage cleaning and sterilization of water tanks through bacteriological treatment by using TERBAC G5/Inchor-5/NB-10/ TERBAC-G-65/ Inoxi-60/NB-69 AND ULTRA VIOLET RAY complete all as specified and as directed. :- (a). First Stage is to drain out the water by using exit valve or high capacity dewatering system. (b). Second stage is cleaning all the algae formation inside the tank by using TERBAC G10/ Inoxi-60/NB-69 a laboratory tested branded chemical of the company and scrubbing the walls of the tanks. (c). Third storage is fresh water cleaning by high speed jet pump. (d). Fourth stage and first bacteria screening is decertification by using TERBAC-G5/ Inohor-5/NB-10 a Govt Laboratory certified brannded halogen compound. (e). Fifth stage is cleaning the floor of water tank by industrial vaccum cleaner. (f) . Sixth stage is the second bacteria screening and sterilizing method by using ultra violet ray within the tank and kills all suspended bacteria. (g) Seventh stage of cleaning and third bacteria screening is to sterilize the floor of the water tank by using laboratory certified, branded strong oxidizing agent TERBAC-G65/Inoxi-60/NB-69 .

All as per item No 166 above, here-in-before but capacity of tank exceeding 1000 ltrs and not exceeding 1000 ltrs.

All as per item No 166 above, here-in-before but capacity of tank exceeding 1000 ltrs and not exceeding 2000 ltrs.

NOTE for Item No.165 to 167:- (i) Test certificate of TERBAC-G65/ INOXIi-60/NB-69 from Government Laboratory mentioning suitability of sterilization should be submitted to the office before using for sterilization. (ii) Outlet pipe of OHT should be plugged before cleaning the OHT to avoid entering scale and the same shall be reconnected after cleaning the OHT and the quoted rate is deemed to include for this provision. (iii) Contractor will be responsible for rectification of complaints occurred during cleaning of tank i.e, no water in tank/over flow due to broken of float valve/blockage of outlet lines due to silt and rectification cost will be deemed to be included in quoted rate. (iv) Date of cleaning with location of site to be notify in sticker and fixed on tanks. (v) The work shall be carried out through specilized agency RAYS CLEANTECH/ INUS WATERTECH/ SATYA ENTERPRISE or other agency as approved by GE.

M&L for applying one coat of white wash to old decorated (white washed) surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for applying one coat of white wash to old decorated (white washed) surfaces of ceiling including preparation of surface complete all as specified and directed.

M&L for preparation of new surfaces of walls including cleaning, watering to make the surface clean and free from dust and applying two coats of acrylic distemper, finished with rollers over a coat of alkali resistant primer complete all as specified and directed.

All as per item No.06 above, but on ceilings

M&L for complete removal of existing treatment on walls including cleaning, watering to make the surface clean and free from dust and applying two coats of acrylic distemper, finished with rollers over a coat of alkali resistant primer and 1mm thick wall care putty, complete all as specified and directed.

All as per item No. 172 above, but on Ceilings

M&L for applying one coat of acrylic distemper, finished with rollers to old decorated surfaces of walls including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss, efflorescent salts, trading oil and greasy spots) complete all as specified and directed.

All as per item No. 174 above, but on Ceilings

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer by using brush, complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

M&L for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

M&L for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of aluminium paint, complete all as specified and as directed.

M&L for applying one coat of acrylic/plastic emulsion paint to old decorated surfaces of wall with rollers including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss, efflorescent salts, trading oil and greasy spots) complete all as specified and directed.

M&L for applying French Polish to old wooden surfaces one or more coats including cleaning and scrapping the same by machine paper, sand paper of different grades , water paper etc filling of stop/ bore holes with putty and french chalk in required quantity complete all as specified and as directed.

M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

M&L for applying one coat of synthetic enamel paint to old painted brick, stone, concrete, asbestos cement or plastered surfaces of any description over 10 cm width or girth including preparation of surfaces all as specified and directed by Engineer -in-Charge.

M&L for applying one coat of cement base paint by using brush on old decorated surfaces of wall including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss, efflorescent salts, trading oil and greasy spots) complete all as specified and directed.

M&L for preparation of old treated/painted surfaces of walls and soffit of chajja, roof slab etc., by cleaning, brooming, rubbing and scrapping as required using broom, emery paper, putty blade/scraper as applicable to make the surface free from loose paint, algae formation, dust etc including necessary safety & protective measures such as safety belt, headgear etc including filling cracks upto 5mm with and including suitable elastomeric crackfill paste and applying one coat of weather proof exterior emulsion paint of approved make using airless spray technology capable of operating single spray gun with hose of adequate length and necessary scaffolding for upto 4 storey building height complete all as specified and directed.

M&L for preparation of new surfaces of walls and soffit of chajja, roof slab etc by cleaning, brooming, rubbing and scrapping as required using broom, emery paper, putty blade/scraper as applicable to make the surface free from protrutions, loose particles, dust etc including necessary safety & protective measures such as safety belt, headgear etc, finishing the surface with 1mm thick exterior wall putty for smooth finish and finishing with two coats of weather proof exterior emulsion paint over a coat of suitable exterior primer of approved make using airless spray technology capable of operating single spray gun with hose of adequate length and necessary scaffolding for upto 4 storey building height complete all as specified and directed.

M&L for cleaning of roofs by getting out growing vegetations / grass & brooming down with removing it out of MD land premises of including repairing to damaged surface of roof by applying two coats of tartaric acid over two coats of CM (1:3) with mixed with 3% WPC & sealed with 85/25 hot blown grade bitumen complete in patch not exceeding 2.0 Sqm each including necessary form work, complete all as directed.

M&L for repairing of damaged portion of mouth at terrace / roof surface of rain water pipe by cleaning and repairing to mouth of RWP by using CM (1:3) with mix with liquid WPC & sealed with 85/25 hot blown grade bitumen complete to make joint of rain water pipe and roof surface fully leak proof complete all as directed by Engineer in Charge.

M& L for repair to chajja area exc 1 Sqm and n exc 2 Sqm each including dismantling of upward facia,cutting of reinforcement , plaster 1:3 or PCC type B0 1:2:4 (using 12.5 mm stone aggregate) on top with WPC, benching/ haunching, repair to broken plaster with dubbing coat including necessary form work complete all as directed.

Dismantling of birck tiles or terracing tiles, single layer on roofs complete all as specified.

Dismantling timber fillets, rails, posts, rafters, purlins, etc under 40 Sqm in section complete all as specified.

M&L 40mm thick brick tiles bedded in cement mortar 1:6 and joints grouted flush in 15mm thick cement mortar 1:3 mixed with 5% of crude oil, complete all as specified.

M&L for second class hard wood clean sawn in scantlings etc., complete all as specified.

S&F 35mm thick factory made plan framed, paneled shutter (two panel) 2nd Class HQ rail and style with lock rail and panel of 9mm BWP commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part-I), Kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L mirror polishing on marble/ granite/kota stone work etc where ever required to give high gloss finish complete all as specified and directed.

S&F special quality self driven screws 50mm to 75mm long with washer, 6mm dia driven from top using Elec/ Mech drilling machine for fixing of Galvalume sheets/ MS angle or flat iron and top of screw filled with 1st quality of silicon etc complete all as specified and directed.

S.K. TRADERS

JOY-EN-JOY

JAGATMATA ENTERPRISE

DGR CONSTRUCTION

RAJ ENTERPRISE

MS AP CONSTRUTION AND CO

dutta and dutta