Annual maintenance work for day to day repair and maintenance work such as civil repair, sanitary, carpentry, grass, drain, tank cleaning work, water supply etc. for Residential Quarters and Non-Residential Buildings at Ekta Nagar Colony under Charga

Amount

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. metres and under including cutting the patch in proper shape and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 metres lead :With cement mortar 1:4 (1 cement : 4 fine sand)

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge.1:3:6 or richer mix

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead:Of area 3 sq. metres and below

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge.

Dismantling W.C. Pan of all sizes including disposal of dismantled materials i/c malba all complete as per directions of Engineer-in-Charge.

Renewing glass panes, with putty and nails wherever necessary:Float glass panes of thickness 4 mm

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 40mm thick with 20mm nominal size stone aggregate

Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primerUsing flats 30x6mm for diagonal braces and central cross piece.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-incharge, manufacturer's specification & drawing. 30 mm thick plain PVC door shutters

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked black enamelled M.S butt hinges with necessary screws excluding, panelling which will be paid for separately.Kiln seasoned and chemically treated hollock wood 30 mm thick shutter

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows ( Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick

Providing and fixing white vitreous china water closet squatting pan (Indian type) Orissa pattern W.C. pan of size 580x440 mm

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.10 litre capacity - White

Applying priming coat :With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :300x16 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :200x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :150x10 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :125 mm

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete :100 mm

Providing and Supplying 12mm thick BWP plywood (ISI mark )approved brand as per direction of Engineer incharge.

Providing and Supplying Hard wood for preparation of frames for door & window,battens & bracings for battered & braced doors,shutters etc. all complete job as per instruction of Engineer-in-charge 30 mm thick shutters

Cleaning wild grass/shrubs vegeations/bushes up to 10cm girth by engaging brush cutter machine and removal of rubbish up to a distance of 50mtrs. Out side the periphery of the area cleared. The cost is incusive of hireing charges of machine POL, operator, cuting tools and Grass should be cut nearest to the ground level. Surface area wher ever brush cutter can not be used should also be cleared by engagng manpower. etc all complete as per instructions of E/L

Transportation of rubbish/branches of cut trees by engaging tractor - trolly, clearing the area as per the instruction of the Engineer-in-charge with a lead up to 2 Km.

Drain cleaning including removing the much, slush, sludge , plastic disposal to a distance of 50 mtrs. OR nearest dust bins or to the place designated by the Engineer-in-charge. Making the surrounding of drain clean on either side of the drain up to a maximum of 1mtr.Whenever possible, spreading bleaching powder whenever required after drain cleaning is done. Work is to be done as per instruction of Engineer-in-charge. (a) Drain size below width of 500 mm. ( Bleaching powder will be supplied by department).

Drain cleaning including removing the much, slush, sludge , plastic disposal to a distance of 50 mtrs. OR nearest dust bins or to the place designated by the Engineer-in-charge. Making the surrounding of drain clean on eigther side of the drain up to a maximum of 1mtr.Whenever possible, spreading bleaching powder whenever required after drain cleaning is done. Work is to be done as per instruction of Engineer-in-charge. (a) Drain size above width of 500 mm. ( Bleaching powder will be supplied by department).

Collection and disposalof all type of garbage by deploying mechanical means (preferably Tractor Trolly ) from the dustbins of colony or from the places as designated by Engineer-in-charge. Garbage is to be collected on regular basis and disposal of the same at designated places with a lead of 2 Km ( No voide shall be deducted while calculating the volume).

Cleanign of RCC and HDPE overhead tanks in heights and level removing all dirt, silt etc, by using required bruch, bleaching powder once in a four month as per instruction of engineer in charge.500 Ltr. Capacity

Cleanign of RCC and HDPE overhead tanks in heights and level removing all dirt, silt etc, by using required bruch, bleaching powder once in a four month as per instruction of engineer in charge.1000 Ltr. Capacity

Welding by gas or electric plant including transportation of plant at site etc. complete.

Assistant to departmental fitter by engaging uskilled manpower in attending minor/major water supply complaints as per instruction of Engineer in-charge.

Providing sanitary workers for cleaning of jammed sewarage line/inspection chambers/ manhole,bath/kit jammed Citrap by taking out nahani trap, precast slab wherever requried and re-fixing same etc.all complete job including disposal of dead bodies of dogs, cast and other small animals etc. from colony premises as per instruction of Engineer in-charge.

Attending day to day comlaints related to carpaintary works such as easing in door/window , repairing of old door/window shuutter preparation of new shutters including tools and plants required for carpaintary works etc all complete as per direction of Engineer-in-charge

Brick work with common burnt clay modular bricks of class designation 7.5 in foundation and plinth in:Cement mortar 1:4 (1 cement : 4 coarse sand)

12 mm cement plaster finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand)

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Supplying of water proofing compound of approved manufacture etc.complete as per instruction of Engineer-in-charge

Application of water proofing compound by deploying necessary manpower and other itms etc.complete as per instruction of Engineer-in-charge

Distempering with 1st quality acrylic distemper (ready mixed) having VOC (Volatile Organic Compound ) content less than 50 gram/ litre, of approved brand and of required said and colour complete to give and even said.Old work (one or more coats)

Supplying and erecting Centrifugal water pump (Monoblock), 415 V, three phase 50 cycles A.C. supply of 11.25 KW/ 15 HP with discharge 10.5/19.4 Litres per second (LPS) for head of 30/54 m and 80 mm suction/ 65mm delivery pipe of size or with discharge of 17.5/36.8 Litres per second (LPS) for head of 18/36 m and 100mm suction/ 100mm delivery pipe of size, on provided C.C. foundation as per specification no. WP-CGP

Providing and fixing PTMT bib cock of approved quality and colour.15mm nominal bore, 86 mm long, weighing not less than 88 gms.

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :150 mm diameterClass I

Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. (the tail pieces if required will be paid separately) :100 mm diameterClass I

Total impact of GST for the purpose of CTC

Md. Aslam Beg (BID ID -1113271)

SANTOSH KHOLGADE (BID ID -1113315)

JAIPRAKASH SINGH (BID ID -1112956)

SURENDRA S. PRASAD (BID ID -1113204)