WORK05

Earth work in excavation in foundation, trenches etc. includingdressing of sides and ramming of bottoms, including getting out theexcavated material, refilling after laying pipe/ foundation anddisposal of surplus excavated material at a lead upto 50m suitablesite as per direction of Engineer for following depths, below naturalground / Road top level.

depth up to 1.5 mtr

Add extra for over all depth of excavation above 1.5 m and upto 3.0m

Add extra for over all depth of excavation above 3.0 m and upto 4.5m

Add extra for over all depth of excavation above 4.5 m and upto 6.0m

Providing and laying in position cement concrete of specified gradeexcluding the cost of centring and shuttering - All work upto plinthlevel :1:4:8 (1 Cement : 4 fine/ coarse sand : 8 graded stone aggregate 40mm nominal size).

Providing and laying in position specified grade of reinforced cementconcrete excluding the cost of centring, shuttering, finishing andreinforcement - All work upto plinth level :1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20mm nominal size)

Centring and shuttering with plywood or steel sheet upto two storiesor height upto 7.5 metre above plinth level including strutting,propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinthand string courses etc.

Reinforcement for R.C.C. work at all levels including straightening, cutting, bending, placing in osition and binding all complete.Thermo-Mechanically Treated bars.

Brick work with FPS bricks of class designation 75 in foundation and plinth in:Cement mortar 1:6 (1 cement : 6 coarse sand)

Cement plastering including T&P, scaffolding, material and completelabpour, including cost of water, curing, racking of joints etc. with 12mm cement plaster of mix : 1:4 (1 cement : 4 fine/ coarse sand)

Distempering with oil bound washable distemper of approved brandand manufacture to give an even shade New work (two or more coats) over and including priming coat withcement primer.

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators side /top /centre hung with beading and allmembers such as F7D, F4B, K11 B and K12 B etc. complete ofstandard rolled steel sections, joints mitred and flash butt weldedand sash bars tenoned and rivetted with 15x3mm lugs, 10cm ong,embedded in cement concrete blocks 15x10x10cm of 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominalsize) or with wooden plugs and screws or rawl plugs and screws orwith fixing clips or with bolts and nuts as required, includingproviding and fixing of hinges, pivots, float glass panes with glazingclips and special metal sash putty of approved make and a primingcoat of approved steel primer excluding the cost of metal beading and other fittings except necessary hinges or pivots complete as per approved design.

Providing and laying in position cement concrete of specified gradeexcluding the cost of centring and shuttering - All work upto plinthlevel :1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mmnominal size)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:

P/Laying ISI marked P.V.C. insulated submersible cable confirming to(IS:694) and as per IS 8130 : 2013 of 1.1 kV grade . Wire should be made from 99.90 % purity copper, stranding in acc. to IS:8130/IEC 60228 for lower watt loss , oxygen free for less chances of oxidization, insulation PVC type A/C/D , flame retardant as per IS 10810-53, better amperage rating as per IS:3961 part 5, existing pipe / open trench / Cable tray / on surface including making connection etc. as required. For additional technical parameters of product / work refer Annexure 'A' attached with this BSR 10.0 Sq.mm 3 core flat / Round

Supply, installation and commissioning of Mono Rail Single Girder Crane suitable for lift up to 9m with chain 9m pulley block and traveling trolley excluding cost of girder complete in all respect as per the direction of the Engineer. 1 MT Capacity

Supply delivery at site with necessary packing, receiving, unloading,shifting, storing, installation, testing and commissioning of Non logsubmersible pumping set of 2% Ni CI Cascading, Impeller CF 8M,Shaft SS 410,mechanical seal with 10M Power & Control cable , 5MGalvanized Chain,,10M, 50mm MS galvanized Guide pipe, Duck FootBend, with Guide wire SS 304 etc. complete with all respect as per specification Discharge 110 cum/hr and head 16 to 20 M

Fabrication, supply of flanged/ plain ended MS pipe made from MSsheet strips of relevant IS specification of approved thickness bywelding, lowering, laying, aligning, fixing in position at all level/depths in trenches complete (excluding flanged jointing wherever required) including al material, labour, testing and mmissioningalong with pipe line as per Technical ecifications and as perdirection of gineer.MS pipe upto 600mm dia (with minimum 5mm thickness sheet)

MS pipe specials upto 600mm dia (with minimum 5mm thickness sheet)

Providing, lowering, laying, aligning, fixing in position in pipe line, Resilient Seated D/F DI Sluice valves of approved make & design standard of following dia complete (including jointing & jointing material ) including all material, labour, testing and commissioning along with pipe line as per Technical Specification & as per direction of Engineer.MANUALLY OPERATED 150 MM DIA

Providing, lowering, laying, aligning, fixing in position C.I. D/Fmanually operated long body butterfly valves (IS: 13095) PN-1.0 class of following dia complete (including jointing and jointing material) including all material, labour, testing along with pipe lineand commissioning as per Technical Specifications and as perdirection of Engineer 150 MM DIA

Dismantling of existing structures like culverts, bridges, retaining walls, CC road and other structure comprising of masonry, cement concrete, wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 50 metres as directed by Engineer. Rubble stone masonry in cement mortar.

Carriage of Materials by mechanical transport including loading, unloading and stacking ::Stone,boulders,gravelly material upto 3 km

Providing and laying un-reinforced, plain cement concrete mix withConcrete Mixer & vibrator pavement over a prepared sub base with 43 grade cement , coarse and fine aggregate conforming to IS: 383,maximum size of coarse aggregate not exceeding 25 mm, mixed asper approved mix design, laid, spread, compacted and finished in a continuous operation including provision of contraction, expansion,construction and longitudinal joints etc including all material, labour,machinery, lighting, guarding and maintenance of diversion.M-20

Wiring of light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) on surface ISI marked ( IS:14927 P - II ) virgin material UPVC trunking & it's accessories, Hot Dipped Galvanized Modular box of 1.2 mm thick with earth terminal/ Surface Moulded virgin material UPVC Modular Box , 10 A Modular switch,Modular face plate with grid plate, 3 pin ceiling rose/holder /3 way Connector, screws, making connections, testing etc. as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter-53, 54 & 56 for additional technical parameters of product / work refer Annexure 'A' Short point (up to 3 mtr.)

Medium point (up to 6 mtr.)

Please Enable Macros to View BoQ information