PROVISION OF ADDITIONAL PERIMETER LIGHTS TO ILLUMINATE PERIMETER WALL AT 24 ED AF MANAURI

Amount

Excavation in trenches in any type of soil not exceeding 1.5 metre deep and not exceeding 1.5 mtr width and getting out soil including forming bottom surface to required slope/gradient for laying cables/pipes/pole foundation etc complete all as specified and directed.

Returning & filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 CM thick in soft/ loose soil, complete all as specified and directed.

Removal of surplus excavated soil to a distance not exceeding 50 Mtr and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

M&L for sand cushioning (dry sand) to under ground cable for cable protection with layer of 8 cm deep before laying the cable and 15 cm depth after laying the cable, complete all as specified and directed. Note : Punned thickness of sand layers shall be measured and paid contractor.

Supply and laying bricks for protection of cables using sub class "B" bricks laid dry flat across length of the cable with width equal to the length of brics complete all as specified and directed.

Supply and Laying in trenches / fixed to wall/ drawn in pipe/duct/laid in floor XLPE insulated screened,PVC bedded and sheathed and steel wire/strip armoured cable 1100V grade with stranded aluminium conductor of cross sectional area 16 Sqmm 4 core complete all as specified and directed.

Supply and Laying in trenches / fixed to wall/ drawn in pipe/duct/laid in floor XLPE insulated screened,PVC bedded and sheathed and steel wire/strip armoured cable 1100V grade with stranded aluminium conductor of cross sectional area 25 Sqmm 4 core complete all as specified and directed.

S&F new generation energy saving & environmental friendly long life LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminium housing with toughened glass and heat resistant and individual high power LED's complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics,high efficiency >120 lm/W with IP 66 protection including making electric connection with three core copper cable with all accessories complete all as specified and directed.

S&F new generation energy saving & environmental friendly long life LED flood light 120 watt 230 V AC outdoor type with high pressure die cast aluminium housing with toughened glass and heat resistant and individual high power LED's, high efficiency >120 lm/W with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp including making electric connection with three core copper cable with all accessories complete all as specified and directed.

S&F new generation energy saving & environmental friendly long life LED flood light 250 watt 230 V AC outdoor type with high pressure die cast aluminium housing with toughened glass and heat resistant and individual high power LED's ,high efficiency >120 lm/W with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp including making electric connection with three core copper cable with all accessories complete all as specified and directed. Make- Bajaj Cat part no. GLEAM-GF 300L WHNB-A5 PC SD or equivalant make of havells or Philips.

Supply, erecting and fixing in true vertical position , steel tubular swaged poles complete with MS base plate ,final taper plug,bolts,nuts and screws as specified type 410 SP-31 (9.0 meters long) Including black bituminous paint in inner portion & upto planting height, all necessary excavation & earth work in any type of soil for foundation of poles, PCC 1:3:6 type (C-2) (using 40 mm graded stone aggregate ) in foundations below GL, PCC 1:2:4 type (B- 1 )(using 20 mm graded stone aggregate) in plinth block(coping) of size 600 X 600 X 300 mm above GL , removing surplus soil to a distance n. exc. 50 m & depositing where directed, including necessary form work and and providing 3 Nos of 30cm wide circular bands with Aluminium & blue paint starting from plinth level at a gap of 30cm in between 2 bands and numbering of poles, and numbering of the poles shall be done with synthetic enamelled painted letter of shape & size complete. inclusive of one primer coat, one under coat and one finishing coat of aluminium paint complete all as specified and directed. Note - Excavation and PCC work shall paid separately through relevant item of BOQ.

Supply, install, testing and commissioning of 16 mtr High Mast, polygonal, continuous tapered, and flange mounted type single hot dip galvanized, no circumferential weld and suitable for wind velocity as per IS 875 part 3 fabricated out of special steel plates as per BSEN-10025, grd mild steel, the mast shaft shall be supplied in two sections top dia : 150mm, bottom dia : 360mm approx, and Terrain factor in TC-1(airport) and shall be stress fitted at site mast door opening size 1200mmx300mm along with supply of accessories for 16 mtr high mast which includes head frame, lighting finial, stainless steel wire rope, compensating disc for three wire rope system, double drum winch with capacity of 750 kg, power trailing cable integral power tool, GLC aviation obstruction LED light, control panel housing comprising of suitable timer-contactor circuit for automatic ON/OFF of high mast lights galvanised lantern carriage suitable for mounting 09 Nos Luminaires LED 200 watt 230 Volt flood light symmetrically incl following items : (a) Supply & fixing 09 No.s flood light luminaire with high power LED powder coated pressure die cast aluminium compact energy saving & environmental friendly long life heat resistant toughened glass of rating 200 watt,with lumen efficacy not less than 120 lumen per watt, CRI more than 85, colour temperature 5500K to 6000K surge Protection 5 KV (Min), for pole height 16 meter, Led driver constant voltage and current for input voltage of 140 to 285 Volt, power factor not less than 0.95, 240 volts, 50 Hz with not less than IP66 protection. (b) Design, casting of suitable foundation for 16 meter high mast consider SBC as 10 Ton/sqm at the depth of 1.5 mtr, along with erection and mondern Engg practice incld 02 nos GI pipe earthing stations.

Note for item No. 12.00 Rate quoted is deemed to be included of following also:- (i) The structure should be capable to withstand the wind load as per IS : 875, necessary backup with structural design to be provided for these purpose which should determine the basic geometric configuration of MAST to be used for given application. (ii) The luminaries should be mounted on the lantern carrige by luminaries mounting arm assembly and should aim properly to achive the desired lightning performance. Wind speed is 50M/Sec. (iii) The lantern carriage should be of raising and lowering type and for this purpose a THREE WIRE SUSPENSION system of stainless steel wire rope of adequate size along with a double drum winch to be provided for most optimum balancing of the lantern carriage. Tower tool should be integrated. (iv) COMPENSATING DISC and SAFETY WIRES to be provided for maximum safety and flexibility. (v) The self lubricating WINCH gear assembly should be made of phosphor bronze. (vi) RCC foundation as per manufacturer's recomendations (vii) The power tool should be built in type.

S&F 1100 volts grade heavy duty cable PVC insulated aluminium conductor 2.5 Sqmm 2 core ISI marked LT Cross Linked Polythene insulated (XLPE insulated) glavanised steel strip armoured electric cable along the poles or passing through pipes or laid under floor or through pipes or laid under floor of through walls complete all as specified & directed.

S&F LT cable junction box dust and whether proof made out of PVC non metallic sheet FRP type, factory made out of PVC non metalic sheet FRP type, factory made, size of box 250mm x 200 mm x 100 mm deep with swivelling cover and locking clamp, MS clamps and nuts, bolts, for fixing the box on steel tubular pole, consisting of aluminium bus bar strip 150mm x 30 mm x 3 mm - 04 Nos mounted on pole and provision of incoming and outgoing PVC insulated cable with grommets including inbuilt 6 Amp MCB SP 10 KA-01 Nos complete all as specified and directed. Make : Sintex CAT part No GS-JB2520 or equivalent CAT part of make Hensel.

S&F Digital timer switch with Timelite DBs outdoor type factory made powder coated all along internal and external surfaces, weather proof dust/water proof with IP 55 protection, consisting of 01 No AC contractor three phase 32 Amp capacity 25 KA, one digital Timer switch three nos MCB 32 Amp 10 KA toggle switch having both auto manual and by pass system - 01 Nos mounted on existing pole/panel with suitable size clamps complete all as specified and directed.

M&L for 40 mm bore galvanized steel tubing, “light grade” with all fittings/clamps, bolts, nuts & washer etc. for cable protection laid in trenches for road crossing/ footpaths etc. complete all as specified and directed.

M&L for 15 mm bore galvanized steel tubing, “light grade” with all fittings / clamps, bolts, nuts & washer etc. for cable protection laid along the pole between light bracket and junction box etc complete as specified & as directed.

S&F bracket for street light fittings made out of 32 mm dia "medium grade" galvanized steel (GI) tubing of 1.5 m long, bent to required shape (having an angle 120 degree) including necessary FI clamp (02 Nos of size 40 x 5 mm) nuts, bolts and washers and fixing to the pole complete after taking down old unserviceable bracket from the pole complete all as specified and directed.

M & L for plain cement concrete (1:4:8) type D2 (using 40mm graded stone aggregate) for foundation of poles, Stay assembly, struts, etc. including all necessary formwork complete all as specified & as directed.

M & L for plain cement concrete (1:3:6) type C2 (using 40mm graded stone aggregate) for foundation of poles, Stay assembly, struts, etc. including all necessary formwork complete all as specified & as directed.

M & L for plain cement concrete (1:2:4) type B2 (using 40mm graded stone aggregate) for foundation of poles, Stay assembly, struts, etc. including all necessary formwork complete all as specified & as directed.

Dismantling and taking out street light steel tubular poles of any size embedded in concrete upto bottom of foundation with the help of crane,hydra or suitable T&P and transporting/ Stacking for re-use and refixing steel pole to new location within Manauri AF campus incl all necessary excavation & earth work in any type of soil for foundation of poles, PCC in foundations below GL and in plinth block(coping) above GL , removing surplus soil to a distance n. exc. 50 m & depositing where directed, including necessary form work and providing 3 Nos of 30cm wide circular bands with Aluminium & blue paint starting from plinth level at a gap of 30cm in between 2 bands and numbering of poles, and numbering of the poles shall be done with synthetic enamelled painted letter of shape & size as directed. inclusive of one primer coat, one under coat and one finishing coat of aluminium paint complete all as specified and directed. Note- Rate is inclusive of Necessary excavation and PCC work.

Supply, installation, testing and commissioning LT 415 volt, 4 wire AC 50 HZ cubical panel factory made, CPRI approved outdoor KIOSK padestal type, dust & vermin proof fabricated of 3.0mm thick MS black sheet, duly high class powder coated paint with, locking arrangement and two earth terminals suitable cable glands for all incoming & outgoing cables including grouting of LT panel on duct or PCC foundation with suitable nut, bolt & washer complete all as specified and directed by Engineer-in-charge including the following accessories components:- (i) Incoming MCCB 4 pole, 63Amp capacity, adjustable type with rupturing capacity 35 KA- 01 Nos. (ii) Aluminium bus bar suitable size and thickness for RYB current rating 250Amp - 01 set Note:- All incoming and outgoing connection in MCCB/fitments carried out through suitable rating aluminium strip/lugs

M/S Aarav Construction (BID ID -3340572)

chauhan construction (BID ID -3339339)

M/S SWASTIK BUILDERS (BID ID -3340283)

M/S ANKIT ENTERPRISES (BID ID -3342387)

K R GUPTA AND SONS (BID ID -3338361)

gangotri enteriprises (BID ID -3340357)

M/S vibhuti enterprises (BID ID -3338456)

M/S VIJAY SINGH (BID ID -3342767)

HIMANSHU TRADERS (BID ID -3339145)

HARSH ASSOCIETES (BID ID -3341424)

M/S SHIV BALLABH MISHRA (BID ID -3342481)

A S ENTERPRISES (BID ID -3341672)

Avion Industries (BID ID -3342591)

M/S AM ENTERPRISES (BID ID -3342978)

DKS ENGINEERING WORKS (BID ID -3342802)

m/s neeraj kumar shukla (BID ID -3342666)