Construction of Theme Park in Shirdi Nagar Parishad Premises, Tal. Rahata, Distt. Ahilyanagar.

Amount

Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 metre) By Mechanical Means

Excavation for foundation in earth, soils of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 metre to 3.0 metre) By Manual Means

Excavation for foundation in Hard murum and boulders including removing the excavated material upto a distance of 50 metres, beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 metre to 3.0 metre) By Mechanical Means

Filling in plinth and floors with approved excavated material in 15 centimetre to 20 centimetre Layers including watering and compacting etc. complete.

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 centimetre to 20 centimetre thick including hand packing and compacting etc. complete.

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 centimetre to 20 centimetre including watering and compaction etc. complete.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per One Square Metre of surface area covering ten years guarantee on bond paper.

Providing and laying Cast in situ/ Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/ Ready Mix cement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork, cover blocks, laying/ pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/ Ready Mix cement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

First Floor

Providing and laying Cast in situ/ Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

First Floor

Providing and laying Cast in situ/ Ready Mix cement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

First Floor

Providing and laying Cast in situ/ Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, cover blocks, laying/ pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/ Ready Mix cement concrete M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

First Floor

Providing and laying Cast in situ/ Ready Mix cement concrete in M-25 of trap/ quartzite/ granite/ gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block). (Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C.coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/ pumping, compacting, curing, finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)

First Floor

Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

First Floor

Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls/ in plinth external walls including bailing out water manually, striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete.

Providing fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete

First Floor

Providing Second class fly ash brick masonry with conventional/ I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of two bars of 6 millimetre diameter/ two hoop iron strips 25 millimetre x 1.60 millimetre at every third course, properly bent and bounded at ends scaffolding raking out joints and watering etc. complete.

Brick work with common burnt clay machine made modular bricks of class designation 12.5 in exposed brick work including making horizontal and vertical grooves 10 millimetre wide 12 millimetre deep complete in cement mortar 1 : 4 (1 cement : 4 coarse sand)

First Floor

Providing internal cement plaster 12 millimetre thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete.

First Floor

Providing internal cement plaster 20 millimetre thick in Single coats in cement mortar 1:4 without neeru finish, to concrete, brick surface, in all positions including scaffolding and curing etc.complete.

First Floor

Providing and laying mud plaster 10 to 12 millimetre thick in mud mortar mixed with bhusa @ 35 kilogram per cubic metre of earth and gobri leaping with mix 1:1 (1 clay : 1 cow dung) in Single coat, to concrete, brick surface, in all positions including scaffolding and curing etc.complete.

First Floor

Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 millimetre thick in cement mortar 1:4 using waterproofing compound at 1 Kilogram per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 millimetre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

First Floor

Providing vee pointing with cement mortar 1:3 for stone/ Brick masonry including scaffolding and curing etc. complete

First Floor

Providing and fixing chicken mesh of 22 gauge, with about 30 centimetre width at the junction of R.C.C members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /B.B.masonry and or tying by binding wire etc. complete.

First Floor

Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete.

First Floor

Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.

First Floor

Providing and applying 2 Coats of high quality acrylic copolymer matt approved low VOC emulsion paint of approved shadethat gives smooth, flat and washable and durable finishing of approved make. Paint should have good flow levelling property with good colour retention and incan antibacterial property. Paint has to be applied on smooth and uniform surface prepared by an acrylic copolymer low VOC & Odour putty. This surface should be primed with water based low VOC acrylic copolymer based primer sealer that has incan antibacterial property. The work activity should cover all aspects of applying paints from surface preparation, filling to erecting and dismantling of scaffolding, finishing the surface etc as directed by Engineer in charge.

First Floor

Providing and applying two coats of exterior weather shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning, preparing the plaster surface, applying primer coat, scaffolding if necessary, and watering the surface for two days etc complete.

First Floor

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 millimetre. thick layers of same mortar added with jute fiber at 1Kilogram per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300 millimetre x 300 millimetre making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete.

Providing water proof bedding for flooring of Bath and WC 25 millimetre thick in C.M. 1:3 including using approved water proofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling, curing and covering 10 years guarantee on court fee stamp paper of Rs.500/- including ponding test etc. complete.

Providing waterproof plaster in W.C. and bath 12 millimetre thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing etc. complete. (Excluding Tiles) (As directed by Engineer in Charge)

Providing and laying ceramic tiles having size 30 centimetre x 45 centimetre confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.

Providing and laying Antiskid Ceramic tiles of approved quality of size 30 centimetre x 30 centimere and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.

Providing and laying vitrified matt finish tiles having size 590 millimetre to 605 millimetre x to 605 millimetre of 8 to 10 millimetre thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning etc. complete.

Providing and laying vitrified matt finish tiles having size 590 millimetre to 605 millimetre x to 605 millimetre of 8 to 10 millimetre thickness and confirming IS. 15622-2006 (Group Bla) of approved make, shade and pattern for dado and skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc. complete.

Providing and laying machine cut machine Polished Kota stone flooring 25 millimetre to 30 millimetre thick and required width in plain/ diamond pattern on bed of 1:6 C. M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete.

First Floor

Providing and fixing in required position skirting or dado of polished Kotah Stone slab 25 millimetre to 30 millimetre thick fixed on base on plaster of cement mortar 1:4 including cement float, filling joints with cement slurry, curing rubbing, polishing and cleaning complete.

First Floor

Providing and laying machine cut machine polished machine cut Kota stone slabs 20 to 25 millimetre thick for treads and risers of steps and staircases, with rounded nosing for the treads on a bed of 1:4 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete.

First Floor

Providing Mirror polishing to Kota Stone including using all necessary stones and equipments cleaning, washing etc. complete. For Flooring

First Floor

Providing Mirror polishing to Kota Stone including using all necessary stones and equipments cleaning, washing etc. complete. For Skirting

First Floor

Providing and laying 18 to 20 millimetre thick Udaipur Green/ jaiselmer Marble of approved quality and colour with machine polished surface, on a bed of cement mortar 1:4 for flooring, sills, riser, dado, window boxing including cement float, filling joints with neat cement slurry to match the colour of the slabs, curing, polishing, nosing/ moulding the sharp edges, cleaning etc. complete.

First Floor

Providing and laying 20 millimetre to 25 millimetre thick White marble of approved quality and colour with machine polished surface, on a bed of cement mortar 1:4 for flooring, sills, riser, dado, window boxing including cement float, filling joints with neat cement slurry to match the colour of the slabs, curing, polishing, rounding edges, cleaning etc. complete.

First Floor

Providing and laying 40 millimetre thick rubbed Red sand stone flooring, coping, tread and riser over 20 millimetre (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints 3 millimetre thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar.

First Floor

Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 millimetre x 20 millimetre x 4 millimetre in all colour, design, fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kilogram per square metre and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge:

Stone work (machine cut edges) for wall lining etc. (veneer work) with 30 millimetre thick sand stone exposed face fine dressed with rough backing for all heights, backing filled with a grout of average 12 millimetre thick cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately)

First Floor

Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required.

First Floor

Providing and fixing copper pins 7.5 centimetre long 6 millimetre diameter for securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement : 2 coarse sand), including making the necessary chases.

First Floor

Providing and laying telephone black/ Amba White/ Cadburybrown/ Ruby red/ Ocean Brown granite stone of 18 to 20 millimetre thick for door frame/ dado/ window boxing etc. On C.M. 1:6 including filling joints with polymer base filler nosing/moulding the sharp edges wherever necessary, curing, etc. complete.

Providing and fixing frame with/ without ventilator of size as specified with Country cut teak wood for doors and windows including chamfering, rounding, rebating, iron holdfast of size 300millimetre x 40millimetre x 5millimetre with oil painting, etc. complete

First Floor

Providing and fixing single or double leaf panelled door shutter excluding frame with glazed openable fanlight shutter 35 millimetre thick as per detailed drawing consisting panelled vertical styles 100 millimetre x 35 millimetre and lock and bottom rail 200 millimetre x 35 millimetre and panels 12 millimetre thick both side commercial ply faced particle board including stainless steel fixtures and fastening and T.W. beading at junctions of panel inserts and as instructed by the Engineer in charge including 3 coats of oil painting etc. complete.

Solid Core Flush door Single leaf Providing and fixing factory made solid core flush door in single leaf 35 millimetre thick, decorative types, of exterior grade, as per detailed drawings, conforming to I.S.:2202 - 1962 (Revised) with approved face veneers on both faces with/without glazing and venetians in the positions shown on the drawings or as directed, all necessary beads, moulding and lipping, holdfasts, mat finish stainless steel fixtures fastenings, finishing with french-polish/ waxing complete. (without door frame). (Sample to be got approved from Ex.Engineer before use) Commercial Hard Wood shutter

First Floor

Solid Core Flush door Double leaf Providing and fixing factory made solid core flush door shutters in double leaves 35millimetre thick,decorative type of exterior grade, as per detailed drawings, conforming to I.S.: 2202 – 1966 (Revised) including approved face veneers on both sides, without glazing and venetians including mat finish stainless steel fixtures and fastening, stoppers and finishing with french polishing etc. (Excluding door frame) (Sample to be got approved from Ex. Engineer before use) Commercial Hard Wood shutter

Providing and fixing 30 milimetre thick Poly Vinyl Chloride FLUSH L DOOR SHUTTER consisting of panel of hollow Poly Vinyl Chloride profile of 20 milimetre thickness consisting frame made out of Mild Steel tubes of 19 gauge thickness and size of 19 milimetre x 19 milimetre inserted inside the hollow section of stiles rails top and bottom rails and two 19 x 19 milimetre Mild Steel tubes inserted horizontally inside the hollow profile section using 4/5 milimetre sheet using screws hollow profile shall be lipped with 10 milimetre (5milimetre x2) thick x 20 milimetre width on stiles and rails using solvent cement. The inner panel shall be laminated with 5 milimetre thick termite proof waterproof plain /prelam Poly Vinyl Chloride sheet using solvent cement on the both sides of the panel including stainless steel fixtures and fastening excetra. Complete as per direction of Engineer incharge, manufacturers specification and drawing.

Providing and fixing in position, Double shuttered aluminium extruded powder coated openable door of specified size with aluminium door frame of powder coated section 101.60 x 44.75 millimetre, 3.18 millimetre thick and shutter comprising of powder coated section having bottom and lock rail of size 150 millimetre x 44.5 millimetre x 3.00 millimetre thick top rails 47.62 x 44.45 millimetre x 3.00 millimetre thick, vertical style 47.62 x 44.45 millimetre, 3.00 millimetre thick and for shutter plain glass panes 5 mm thick for top panels and 12millimetre thick both side laminated phenol bonded particle board panels for bottom panels etc., I.S.I. mark, heavy duty, Hydraulic floor spring of 150 Kilogram capacity, having heavy duty concealed lock, necessary beading, glazing clips, PVC gaskets, 250millimetre length aluminium tower bolts, 150millimetre dia. pad handle, etc. as per detailed design and drawing or as directed by engineer in charge including all materials, labours and equipment etc. complete.

Providing and fixing in position, Single shuttered aluminium extruded powder coated openable door of overall size 0.90 metre x 2.40 metre with aluminium door frame of powder coated section 101.60 x 44.75 millimetre, 3.18 millimetre thick and shutter comprising of powder coated section having bottom and lock rail of size 150 millimetre x 44.5 millimetre x 3.00 millimetre thick top rails 47.62 x 44.45 millimetre x 3.00 millimetre thick, vertical style 47.62 x 44.45 millimetre, 3.00 millimetre thick and for shutter plain glass panes 5 millimetre thick for top panels and 12millimetre thick both side laminated phenol bonded particle board panels for bottom panels etc., I.S.I. mark, heavy duty, Hydraulic floor spring of 150 Kilogram capacity, having heavy duty concealed lock, necessary beading, glazing clips, PVC gaskets, 250 millimetre length tower bolts, 150 millimetre diam. pad handle, etc. as per detailed design and drawing or as directed by engineer in charge including all materials, labours, and equipment etc. Complete

Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 millimetre with lock plate of 3.15 millimetre thickness reinforced with 35 x 35 x 5 millimetre angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65 millimetre and 3.15 millimetre respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15 millimetre minimum size and shape with square bar, suspension shaft of minimum 32 millimetre diameter, hood cover of M.S. sheet not less than 0.9 millimetre thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (I.S. 62481979) (With mechanical gear)

Providing and fixing in position powder coated extruded aluminium fixed window fully glazed of any size as per detailed drawing and as directed by Engineer in charge with all necessary alluminium sections including necessary fixtures and fastening such as 5 millimetre thick clear float glass etc. complete. Note While arriving at the rate of item of item weight at 6.90 Kilogram/ One Square Metre is considered.

First Floor

Providing and fixing in position (as per 1868/ 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 millimetre at weight 0.637 Kilogram/ One Running Metre. with window frame bottom track section 92 x 31.75 x 1.30 millimetre at weight 1.070 Kilogram/ One Running Metre. Top and side track section 92 x 31.75 x 1.30 millimetre at weight 0.933 Kilogram/ Running metre. The shutter should be of bearing bottom 40 x 18 x 1.25 millimetre at weight 0.417 Kilogram/ One Running Metre. Inter locking section 40 x 18 x 1.10 millimetre at weight 0.469 Kilogram/ Running metre. and handle and top section 40 x 18 x 1.25 millimetre at weight 0.417 Kilogram/ Running metre. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 millimetre thick plain glass and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour Anodising without box

First Floor

Providing and fixing in position powder coated aluminium louvered windows/ ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 millimetre x 1.22 millimetre box type, 5 millimetre thick sheet glass louvers, of approved quality etc. complete.

Providing and fixing M.S. grill door 24 Kilogram/ One Square Metre of various size as per detailed drawings without hot dip coating, iron fixtures and fastenings and 3 coats of oil painting etc

Providing and fixing mild steel grill railing 15 Kilogram/square metre with Ghana teak wood hand rail of size 75millimetre x 60 millimetre and sill of 75millimetre.x 25millimetre and newel posts for staircases, including fabricating, fixtures, erecting, painting the grill work with one coat of anticorrosive paint and two coats of oil painting with approved colours and polishing the sill, hand rail and the newel post with french polish.

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted/ bolted /welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete.

First Floor

Providing structural steel work in hollow section of various thickness and sizes in square, rectanular and round shape from 25 millimetre to 450 millimetre section as per IS 4923 YST 310 Grade produced from iron ore and blast furnace route etc. as per detailed designs and drawing or as directed including cutting, fabricating, hoisting, erecting, fixing in position, making riveted/bolted/ welded connections and painting complete.

First Floor

Supplying and fixing of 6millimetre thick Exterior Compact Laminate or High Pressure Laminate of approved colour by approving authority with UV resistant Decorative colour paper on both side typically made out of multiple layers of craft papers and then impregnated with thermosetting phenolic resins, on top of it melamine treated barrier paper and decorative paper and wear layer on both the sides saturated with melamine resins and then covered with UV resistant acrylic resin layer which makes it extremely durable and weather resistant compressed together on extremely high pressure and hardened with electron beam curing to get the total desired thickness of 6mm matching European standard specification as per EN 438 -part 6, protected with 60 Micron protective peel-off film on both side which in no case leave any adhesive mark over the panel surface after it is peeled off. Fixing of the same to be done on a supporting frame of 50 millimetre X 5 millimetre X 3 millimetre powder coated aluminium box section to be spaced horizontally and vertically in 600millimetre X 600millimetre grid and fixed to building structure as per design through 50millimetre X50 millimetre X 5millimetre MS angle bracket prefixed to masonry slab or columns with Hilti make anchor fastener along with all related hardware and fixtures. The panel should then be fixed on the Aluminium section with the help of pure polyester exterior grade colour coating rivets as per architectural drawings or as directed by Engineer-in-charge. Each panel should be riveted on substructure maintaining a gap of 6mm on all the sides between each Panel for Air circulation and expansion and contraction as per installation specifications provided by the manufacturer. The cost shall include all expenses related to storage, material handling, lifting, freight, labour, scaffolding etc as directed by Engineer-in-charge. First Floor

Supply, fixing and installation of 4 millimetre thick Aluminium Composite Panel (ACP) of approved colour for external cladding in combination of solid and metallic colours, including all necessary Framework, support and complete weather sealing as per architectural drawing. The Aluminium Composite Panel (ACP) should be made out of thermoplastic core of low-density polyethylene LDPE (100% virgin mix), sandwiched between two aluminium sheets of ALLOY GRADE- 5000 series, each not less than 0.50 mm thick, total thickness of aluminium composite panels not to be less than 4 mm, the exposed surface thereof shall have Stove lacquered finishing coat not less than (26 +/- 2) micron (containing minimum 70% kynar 500 based PVDF) of colour and shade as per architectural design. The inside surface (facing the building exterior surface)shall have polyster based powder coating not less than 25 Micron with protective peel-off foil on the exterior face (peel off film will in no case leave any adhesive mark over the composite panel surface after it is peeled off). The supporting framework shall be made out of 50 millimetre x 25 millimetre x 3 millimetre thick Aluminium section to be spaced horizontally and vertically for fixing of panel of size 900 millimetre x 1200 millimetre and fixed to the building structure as per design through 50mm x 50mm x 5mm MS angle clamps prefixed to masonry or slab, columns with Hilti make anchor fastener screws. The fixing of panel to be done with the help of VHB tapes and screws and all the sealing of joints to be done with weather sealent Silicon as directed by Engineer-in-charge. (Prior permission of S.E. is necessary before inclusion of this item in estimate) First Floor

Construction of Granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader/ Paver on prepared surface and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- Plant Mix Method and Grading - II Material

Providing, laying, spreading and compacting stone aggregates of specific sizes to Water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with Vibratory roller. to the required density. By Mechanical Means - Grading I (Using Screening Type A (13.2) millimetre Aggregate)

Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate (natural sand/ VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25 millimetre, cement content not to be less than 150 kilogram per square metre, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor by suitable means as approved by Engineer-in-charge, compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etc. complete. with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete.

Providing and laying in situ cement concrete M -30 with tremix treatment for 200 millimetre thickness for Concrete Road is including laying plastic sheet for 125 micron thickness with groove cutting of 4 millimetre wide and 20 millimetre deep with necessary refilling with polysuphide sealent (Pouring grade) confirming to BS : 5212 - 1989 into sawed groove widened at top for sealent reservoir of specified size and shape as per detailed drawing including fixing Polyethylene foam backer rod of required diameter (excluding reinforcement) with coarse and fine aggregate Using V.S.I.Quality Artifitial Sand etc. complete with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete.

Providing and applying Cold plastic paint two component rolled on surfacing material solvent free, high build two pack seamless, tough, skid resistant, material with has property of attaining 2.00 millimetre thickness in single coat application white (or as required colour) based on glass and colour retaining acralic cross linking resin system for coloured road surfacing including surface cleaning and cost of all material etc. complete. (All inclusive on bitumen or concrete surface) work shall carried out as per IRC 35-2015 clause 2.2)

Providing and fixing in position TMT FE 500, 25 millimetre dia dowel bars precoated with anticorrosive epoxy paint of required Dia. 60 centimetre Long and at 30.00 centimetre C/C and wherever directed including handling, straightening, necessary cutting supported by TMT FE 500, chairs with proper alignment by using properly designed assembly of Bulkheads lubricating half length with bituminous paint as directed etc. complete.

Providing and casting in situ or precast tapering R.C.C. M-20 Barrier type Kerb with gutter (as per IRC 86 1983) embedded 125 millimetre below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant

Providing and fixing factory made Hydraulically pressed Mechanically vibrated and compacted precast inter locking Cement concrete paving blocks 80 millimetre thick in M-40 grade of approved size and shape for footpaths, driveway, streets, small/ medium market roads, low volume roads, utility cuts on arterial roads etc. as specified and as per IS 15658: 2006 including cost of all materials, manufacturing, curing, transportation of blocks to work site including loading, unloading and stacking as directed, laying paving blocks in position over prepared bed of natural sand/ crushed sand of 50 millimetre thickness including necessary excavation in all stratas, spreading blindge of fine sand over the prepared bed, compacting blocks by plate vibrator etc. complete.

Providing and Laying factory made coloured chamfered edge Cement concrete grass paver blocks of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine fine aggregate (natural sand/crushed sand VSI grade finely washed etc.), compacting and proper embedding/ laying of inter locking paver blocks into the fine aggregate (natural sand/ crushed sand VSI grade finely washed etc.) bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine aggregate (natural sand/ crushed sand VSI grade finely washed etc.) and cutting of paver blocks as per required size and pattern, finishing and sweeping extra fine aggregate (natural sand/ crushed sand VSI grade finely washed etc.) and complete as per manufacturer spsecifications & direction of Engineer-in-Charge. 60mm thick CC paver block of M-35 grade concrete with approved colour and design & pattern.

Providing and fixing factory made Hydraulically pressed Mechanically vibrated and compacted precast inter locking Cement concrete cobbles 100x100x75 millimetre size in M-35 grade of approved shade for footpaths, driveway, streets, small/ medium market roads, low volume roads, utility cuts on arterial roads etc. as specified and as per IS 15658: 2006 including cost of all materials, manufacturing, curing, transportation of blocks to work site including loading, unloading and stacking as directed, laying cobbles in position over prepared bed of natural sand/ crushed sand of 50 millimetre thickness including necessary excavation in all stratas, spreading blindge of fine sand over the prepared bed, compacting cobbles by plate vibrator etc. complete.

Stamp Concrete of 100mm Thickness - Providing and Laying in-situ M30 Grade unreinforced plain cement stamp concrete of 100 millimetre thickness pavement over a prepared sub base with 43 grade cement, coarse and fine aggregate (natural sand/ VSI grade finely washed crushed sand) Confirming to IS 383, as per mixed in a batching and mixing plant/ non tilting mixer and weigh batcher as per approved mix design, admixtures, transporting to site, spreading, laying with approved make pover, compacted and finished in a continous operation, finishing to lines and grades Also Providing, Placing and applying stamp powder which is light fast UV resistant pigment with appropriate chemical compounds of desired colour on base concrete after excess bleed water has evaporated using dry shake method @5 Kilogram per Square metre. Including texturing, and covering with plastic sheet (min 200 micron thickness) and also applying two coats of UV-stable,30 % solids clear sealer @ 150 to 250 grams per square metre using surface roller and protecting from falling dust,dirt and curring by curring compound/ by providing cement vata in cement Mortor 1 :8 @ 0.6metre x 0.6metre center to center, admeasuring 80mm at bottom and 40mm at top with depth of 75 millimetre and maintaining the same throughout curing period by any other method approved by Engineer-incharge or Landscape architect etc. complete. (prior approval of superinteding Engineer will be necessary )

Supply & Fixing of Rock/ Stone Finished outdoor vitrified flooring Tiles 16 millimetre thick and required width wide in plain pattern including Cement float, filling joints, with neat cement slurry, Natural sand, curing and cleaning complete. with prior approval of concerned Superitending Engineer.

Providing and laying in position flooring of telephone black/ Amba White/ Cat bary brown/ Ruby red/ Ocean Brown granite stone of approved shade and size 18 millimetre to 20 millimetre thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black/ Amba White/ Cat bary brown/ RBI red/ Ocean Brown granite stone for skirting, treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.

Providing and laying 18 millimetre thick Sand ballasted/ Flamed/ Lapatto/ Leather finish Granite stone machine cut in required size, approved shade, color and texture for flooring in required design and patterns, in linear as well as curvilinear portions of the building, treads, landings laid using white cement slurry over 20 millimetre (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and mirror polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Providing and erecting Y type barbed wire fencing with seven rows of wire with 2.45 mm dia G.I. pipe ( Rezan/ concentiDeleted ire 0.75 millimetre diameter ) with hot dip and G.I. coated hooks as per drawing supported on M.S. angle 50 x 50 x 6 millimetre at 2.5 metre centre to centre including fixing and fastening with wire, painting M.S. angles with one coat of red lead primer and two coat of oil paint etc. complete.

Providing and erecting chain link fencing 1.6 Metre height with G.I. chain link of size 50 x 50 millimetre, 8 gauge thick and fixed 75 millimetre above ground level on vertical M.S. Angles of 40 x 40 x 6 millimetre size, includind excavating pits for foundation and embedded in C.C. block of 1:4:8 mix of size 450 x 450 x 670 millimetre at 1.75 metre c/c with iron bar 16 millimetre dia as hold fast including welding link with angle frame at 30 centimetre c/c with nuts and bolts and horizontal M.S. Angles at top and bottom of 25 x 25 x 5 millimetre size and vertical M.S. flat 35 x 5 millimetre and 25 x 5 millimetre horizontal including cross support of 40 x 40 x 6 millimetre angles both side at every corner or bend embedded in concrete blocks of 1:4:8 of size 450 x 450 x 670 millimetre including 3 coats of oil painting etc. complete.

SANITARY FIXTURES Providing and Fixing vitreous china floor mounted (European Type) water closet with 'P" or "S" trap, C.P. bolts, nuts with solid plastic seat & lid, C.P brass hinged rubber buffers with dual flush 3/6 litre capacity cistern with flush pipe, clamp and rubber adapter joint C.P.brass screws and washers complete including cutting and making good the walls and floors wherever required etc. complete in all respect as per direction of Engineer-in-charge. (Make- Euronics: Model No.C001-WC), (Make- Jaquar: Model No.LYS-WHT- 38751S250UFSM) & (Make- Hindware: Cat. No.: 92597)

Providing & fixing white vitreous china wall hung type European type water closet and internal fittings with C.P. bolts, nuts, C.I. chair or other hanging arrangement, with white solid plastic seat and cover with lid, C.P. brass hinge rubber buffers, with accessories,C.I/M.S. brackets painted with two or three coats of enamel paint of approved shade over a coat of primer. C.P. brass screws and wooden cleats, including cutting and making good the wall and floors wherever required. (Make- Euronics: Model No.C003-WC), (Make- Jaquar: Model No.ARS-WHT-39953BIUFSM) & (Make- Hindware:Cat. No.: 92610)

Providing and Fixing Concealed Flushing Cistern with dual flush Actuator, flush-stop function, noise less float valve and fast filling action with all component parts of high quality With Flash Plate complete including fixing frame and set. (Make- Geberit: Model No.109.011.00.1) (Plate Make- Geberit: Model No. 115.045.11.3) (Make- Jaquar: Model No. JCS-WHT-2431) (Make- Hindware: Cat. No. 518236)

Providing and Fixing White vitreous china Under counter wash basin with C.I. brackets painted white, 15 millimetre CP Brass auto closing pillar cock, 32 millimetre dia. C.P. waste, C.P chain and rubber plug, C.P. connecting pipe to wall and C.P wall flange and rubber adapter for waste connection complete including cutting and making good the walls wherever required etc. complete in all respect as per direction of Engineer-in-charge. (Make- WB Euronics: Model No.C016-WB) (MakeSelf Closing Tab- Euronics: Model No.EPT04B-CP)

Providing and Fixing White vitreous china over the counter wash basin with C.I. brackets painted white, 15 millimetre CP Brass auto closing pillar cock, 32 millimetre dia. C.P. waste, C.P chain and rubber plug, C.P. connecting pipe to wall and C.P wall flange and rubber adapter for waste connection complete including cutting and making good the walls wherever required etc. complete in all respect as per direction of Engineer-in-charge. (Make- WB Euronics: Model No.C005-WB) (Make Basin Pillar Cock- Euronics: Model No.RIV-1014R)

Providing and fixing vitreous china urinal with electrical/ battery operated concealed automatic flushing system CP Brass body with C.I. hangers, 15 millimetre dia inlet to built in spreaders with inbuilt waste with C.P flange for urinal complete including cutting and making good the walls and floors wherever required etc. complete in all respect as per direction of Engineer-in-charge. (Make- Euronics: Model No.C020-UR,Sensor Model-EU44BE)

Providing and fixing 15 millimetre nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 grams (Make- Euronics: Model No-RIV-1010R)

Providing and Fixing C.P. brass towel ring "Round" fixed to PVC cleats with C.P. brass screws including cutting and making good the walls wherever required etc. complete in all respect as per direction of Engineer-in-charge. (Make- Euronics: Model No-ACC03)

Providing and fixing SS liquid soap dispenser with push lever assembly with soap refill fixed in wall with Screws complete in all respect as per direction of the engineer-in-charge. (Make- Euronics: Model No-ES05)

Providing and fixing CP Brass Bottle Trap of approved quality & make etc. complete in all respect as per direction of Engineer-in-charge. 32 millimetre dia (Make- Euronics: Model No-EBT32-CP)

Providing and fixing C.P. brass angle valve for basin and geyser points of approved quality conforming to IS:8931 15 millimetre nominal bore (Make- Euronics: Model No-RIV-1003R)

Providing and fixing C.P. Brass Toilet paper holder, including cutting and making good the walls wherever required etc. complete in all respect as per direction of the Engineer-in-charge. (Make- Euronics: Model No-RIV-ACC08)

Providing and fixing Health faucet with 1 metre long Flexible Tube and CP wall hook with PVC & SS Screws wherever required complete as directed by the Engineer-in-charge. (Make- Euronics: Model No-EHF01)

Providing and fixing two way bib cock complete, including cutting and making good the walls wherever required etc. complete in all respect as per direction of Engineer-in-charge. (Make- Euronics: Model No-RIV-1004R)

Providing and Fixing Handicapped set including white vitreous china floor mounted European type water closet including exposed cistern , Flat Back wash basin with one pair of mounting brackets , complete with fittings, seat cover, two no hinged rail 76 centimetre and five nos of grab bar 60 centimetre including 15 millimetre dia autoclosing pillar cock for Handicaped Toilet complete in all respest as per direction of the Engineer-in-charge.

Providing and Fixing CP auto push cock with CP Wall flange for drinking water purpose complete as per direction of the engineer-in-charge. (Make- Euronics: Model No-EPT05 )

Providing & fixing C.P. brass single lever basin mixer without pop up waste system with 450 millimetre long Copper Pipes with nuts and rubber washer including cutting and making good the walls wherever required. (Make- Euronics: Model No-RIV-1021R)

Providing and Fixing C.P cast brass double coat hook fixed to PVC cleats with C.P. brass screws including cutting and making good the walls wherever required. (Make- Euronics: Model No-RIV-EC02)

Providing and Fixing CP Soap dish with PVC plugs with screws and making good the walls wherever required (Make- Euronics: Model No-ACC01)

150 millimetre diametre

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : For 100 millimetre inlet and 100 millimetre outlet.

Providing and fixing C Class G.I. pipes complete with G.I. fittings and clamps,including cutting and making good the walls etc. 32 millimetre nominal bore

40 millimetre nominal bore

50 millimetre nominal bore

Painting of G.I. pipes with two coats of bitumastic paint wrapping polythene tape and applying the final coat of bitumastic paint. 32 millimetre nominal bore

40 millimetre nominal bore

50 millimetre nominal bore

Providing and Fixing Floor drain by fixing G.I. Reducing elbow of 100 x 50 millimetre in cement concrete 1:2:4 at all levels (excluding cost of grating) for connection to floor traps in sunken portions, complete as per required slope as per drawings and as per approval of the engineer-in-charge.

Providing and fixing G.I. inlet fitting with one or more inlets fabricated from 100mm dia G.I. pipe and welded G.I. sockets and fixed to C.I. trap by lead joint as per standard detail.

Providing and fixing cast brass Floor Clean out with suitable insert keys for opening, male threaded joint with G.I. socket lead caulked to soil pipe / waste pipe of C.I. and C.I.(LA) pipe as required complete as shown in the Sketch. 100 millimetre dia

Providing and making Khurras 45x45 centimetre with average minimum thickness of 5cm Cement Concrete 1:2:4 (1 Cement : 2 Coarse Sand : 4 Graded Stone Aggregate 20 millimetre nominal size) over PVC sheet 1 metre x 1 metre x 400 microns, finished with 12 millimetre Cement Plaster 1:3 (1 Cement : 3 Coarse Sand) and a coat of neat cement, rounding the edges and making & finishing the outlet complete.

WATER SUPPLY SYSTEM FOR (INTERNAL) Providing and laying in walls/ceilings/floors 20 mm dia. medium grade having embossed as ISI Mark galvanised iron pipes of 1.63 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and laying in walls/ceilings/floors 25 millimetre dia. medium grade having embossed as ISI Mark galvanised iron pipes of 2.49 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and laying in walls/ceilings/floors 32 millimetre dia. medium grade having embossed as ISI Mark galvanised iron pipes of 3.20 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and laying in walls/ ceilings/floors 40 millimetre dia. medium grade having embossed as ISI Mark galvanised iron pipes of 3.68 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and laying in walls/ceilings/floors 50 millimetre dia. medium grade having embossed as ISI Mark galvanised iron pipes of 5.17 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and laying in walls/ceilings/floors 65 millimetre dia. medium grade having embossed as ISI Mark galvanised iron pipes of 5.17 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and laying in walls/ceilings/floors 80 millimetre dia. medium grade having embossed as ISI Mark galvanised iron pipes of 8.57 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and laying in walls/ceilings/floors 100 millimetre dia. medium grade having embossed as ISI Mark galvanised iron pipes of 12.43 Kilogram/metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint , 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 15 millimetre dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ceiling/floor 20 millimetre dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete

Providing and fixing on walls/ ceiling/ floor 25 millimetre dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 32 millimetre dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 40 millimetre dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floor 50 millimetre dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing forged brass lever operated ball valve of full flow with forged brass ball (Machined to mirror smooth finish with hard chrome plated) and spindle with setting and gland of superior quality having minimum working pressure of 16 kiligram per square centimetre etc. complete in all respect. 20 millimetre diametre

25 millimetre diametre

32 millimetre diametre

40 millimetre diametre

Providing, fixing, testing & commissioning of C.I. butterfly valve, wafer end type class PN 1.6 as per I.S:13095 or BS:5155, including necessary nuts, bolts, washers, gaskets etc., complete of following size: (flanges to be paid separately) 65 millimetre diametre

80 millimetre diametre

100 millimetre diametre

Providing, fixing, testing and commissioning of IP 67 (Weather Proof/ Aluminium casing with positoner to indicate the valve position with key type manual overdrive) Motorized Butterfly valve for filling of over head water tank complete with high and low level float type sensors to control the valve. The sensors shall be installed in over head tanks.The sensors will close the valve when water level is high in over head tank and open the valve when over head water tank level is low. The system should be complete in all respects with control panel indicating the position of valve i.e open /closed with accessories like wiring/ conduting/ flanges, nut bolts etc. complete as per approved type and specifications as per instructions of the Engineer - in - charge. 25 millimetre diametre

32 millimetre diametre

40 millimetre diametre

50 millimetre diametre

EXTERNAL WATER SUPPLY SYSTEM (DOMESTIC, FLUSHING,GARDEN HYDRANT) Excavation for foundation in earth, soil of all types, sand, gravel and soft murum,including removing the excavated material up to a distance of 50 metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 0.00 to 1.50 metre.) By Manual Means

Providing and fixing on walls/ ceiling/ floors, 25 millimetre diametre heavy grade having embossed as ISI Mark galvanised iron pipes weight of 3.01 Kilogram/meter with necessary fittings . remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floors, 32 millimetre diametre heavy grade having embossed as ISI Mark galvanised iron pipes weight of 3.89 Kilogram/meter with necessary fittings . remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floors, 40 millimetre diametre heavy grade having embossed as ISI Mark galvanised iron pipes weight of 4.49 Kilogram/meter with necessary fittings and remaking good the demolished portion and applying primer of anti-corrosive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete

Providing and fixing on walls/ ceiling/ floors, 50 millimetre diametre heavy grade having embossed as ISI Mark galvanised iron pipes weight of 6.33 Kilogram/meter with necessary fittings.and remaking good the demolished portion and primer of anti corrossive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ ceiling/ floors, 65 millimetre diametre heavy grade having embossed as ISI Mark galvanised iron pipes weight of 6.33 Kilogram/meter with necessary fittings.and remaking good the demolished portion and primer of anti corrossive oil paint 2 coats Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and making flanged connection for the 80millimetre diametre cast iron pipe line including painting rubber insertion, nuts and bolts etc. complete.

Providing and making flanged connection for the 100millimetre diametre cast iron pipe line including painting rubber insertion, nuts and bolts etc. complete.

Providing and making flanged connection for the 150millimetre diametre cast iron pipe line including painting rubber insertion, nuts and bolts etc. complete.

Providing and fixing screw down for 25 millimetre diametre wheeled stop tap of brass including necessary sockets/union nut complete

Providing and fixing screw down for 32 millimetre diametre wheeled stop tap of brass including necessary sockets/union nut complete

Providing and fixing screw down for 40 millimetre diametre wheeled stop tap of brass including necessary sockets/union nut complete

Providing and fixing screw down for 50 millimetre diametre wheeled stop tap of brass including necessary sockets/ union nut complete.

Providing and fixing screw down for 65 millimetre diametre wheeled stop tap of brass including necessary sockets/union nut complete.

Providing and fixing screw down for 80 millimetre diametre wheeled stop tap of brass including necessary sockets/union nut complete.

Providing and constructing Brick Masonry Inspection Chamber 60centimetre x 45centimetre x90centimetre including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and airtight C. I. cover of 75Kilogram with lid and frame fixed in cement concrete.

Providing and constructing Brick Masonry Inspection Chamber 60centimetre x 45centimetre x90centimetre including 1:4:8 cement concrete foundation 1:2:4 cement concrete channelshalf round G.S.W. pipes, Brick Masonry, plastering from inside and airtight C. I. cover of 75Kilogramwith lid and frame fixed in cement concrete.

Providing, laying and fixing P.V.C. pipe of 25millimetre diametre with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete.Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing, laying and fixing P.V.C. pipe of 32 millimetre diametre with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete.Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing, laying and fixing P.V.C. pipe of 40 millimetre diametre with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing, laying and fixing P.V.C. pipe of 50 millimetre diametre with fittings such as bends,tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing, laying and fixing P.V.C. pipe of 75 millimetre diametre with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete.Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing, laying and fixing P.V.C. pipe of 110 millimetre diametre with fittings such as bends, tees, reducers, clamps, etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

EXTERNAL SEWERAGE & DRAINAGE SYSTEM Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metre beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring andstrutting etc. complete. (Lift upto 0.00 to 1.50 metre) By Manual Means

Excavation for foundation in earth, soils of all types, sand,gravel and soft murum,including removing the excavated material upto a distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5metre to 3.0metre) By Mechanical Means

Providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 450 millimetre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.

Providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 600 millimetre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete

Providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 800 millimetre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 millimetre nominal size) all-round for sewerage pipes including bed concrete as per standard design : 200 millimetre diametre

250 millimetre diametre

300 millimetre diametre

400 millimetre diametre

450 millimetre diametre

600 millimetre diametre

800 millimetre diametre

Constructing brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) with RCC Top slab with 1:2:4 mix (1 cement : 2 coarse sand: 4 graded stone aggregate 20 millimetre nominal size) foundation concrete 1:4:8 mix ( 1 cement :4 coarse sand: 8 graded stone aggregate 40 nominal size), inside plastering 12 millimetre thick with cement mortar 1:3 ( 1 cement : 3 coarse sand), finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 millimetre nominal size) finished with a floating coat of neat cement complete as per standard design. Inside size 90x80 centimetre and 45 centimetre deep including C.I. cover with frame (Heavy duty) 455x610 millimetre internal dimensions, total weight of cover and frame to be not less than 38 kilogram (weight of cover 23 kilogram and weight of frame 15 kilogram) .(Excavation and 15millimetre thick cement plaster at the external surface is included in the item)

Extra depth of manholes Size 90x80 centimetre depth beyond 0.45 metre to 0.90 metre

Constructing brick masonry manhole in cement mortar 1:4 (1 cement : 4 coarse sand) with RCC Top slab with 1:2:4 mix (1 cement : 2 coarse sand: 4 graded stone aggregate 20 millimetre nominal size) foundation concrete 1:4:8 mix ( 1 cement :4 coarse sand: 8 graded stone aggregate 40 nominal size), inside plastering 12 millimetre thick with cement mortar 1:3 ( 1 cement : 3 coarse sand), finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 millimetre nominal size) finished with a floating coat of neat cement complete as per standard design. Inside size 120x90 centimetre and 90 centimetre deep including C.I. cover with frame (heavy duty) 560 millimetre internal diameter, total weight of cover and frame to be not less than 116 kilogram (weight of cover 58 kilogram and weight of frame 58 kilogram) .(Excavation and 15millimetre thick cement plaster at the external surface is included in the item):

Extra depth of manholes Size 120x90 centimetres depth beyond 0.91 metre to 1.67 metre

Constructing Brick Masonry circular type manhole 0.91 metre internal dia at bottom and 0.56metre dia at top in cement mortar 1:4 (1 cement : 4 Coarse sand), inside cement plaster 12millimetre thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40millimetre nominal size) and making necessary channel in Cement Concrete 1:2:4 ( 1 Cement : 2 Coarse Sand : 4 Graded Stone aggregate 20millimetre nominal size) finished with a floating coat of neat cement all complete as per standard design. External surface shall be finished with 15millimetre thick cement plaster 1:6 (1cement : 6 Coarse sand) as per side conditions. 0.91 metre deep with hinged DI cover and frame (heavy duty weight of cover & frame to be not less than 80 kilogram,) 560 millimetre internal diameter, fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 millimetre nominal size) including centering, shuttering all complete.(Excavation and 15millimetre thick cement plaster at the external surface is included in the item) :

Extra depth for circular type Manhole 0.91 metre internal dia , depth beyond 0.91 metre to 1.67 metre

Constructing brick masonry circular manhole 1.22 metre internal dia at bottom and 0.56 metre dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 millimetre thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 millimetre nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 millimetre nominal size) finished with a floating coat of neat cement, all complete as per standard design : 1.68 metre deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560 millimetre internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kilogram. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 millimetre nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 millimetre thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for Circular type Manhole 1.22 metre internal dia (at Bottom) With cement based fly ash bricks of class designation 75, Depth beyond 1.68 to 2.29 metre

Constructing brick masonry circular manhole 1.52 metre internal dia at bottom and 0.56 metre dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 millimetre thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 millimetre nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 millimetre nominal size) finished with a floating coat of neat cement, all complete as per standard design : 2.30 metre deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560 millimetre internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kilogram fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 millimetre nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 millimetre thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 1.52 metre internal dia (at bottom) beyond 2.30 metre

Constructing brick masonry catch basin with 75 class designation bricks in cement mortar 1:5 (1 cement: 5 coarse sand), 150 millimetre thick foundation concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40mm nominal size) inside and outside plaster in cement mortar 1:3 (1 cement: 3 coarse sand). inside finished with floating coat of neat cement, making haunches and channel in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 millimetre nominal size) neatly finished, complete as per standard design including excavation, refilling and disposal of surplus earth. Size 450X450X450millimetre inside with precast S.F.R.C. grating of approved design and sample fixed in Plain Cement Concrete 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 millimetre nominal size) including centering, shuttering all complete as per site conditions.

Size 600X600X600 millimetre inside with precast S.F.R.C. grating of approved design and sample fixed in Plain Cement Concrete 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 millimetre nominal size) including centering, shuttering all complete as per site conditions.

Size 750x750x750millimetre inside with precast S.F.R.C. grating rectangular of approved design and sample fixed in Plain Cement Concrete 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 millimetre nominal size) including centering, shuttering all complete as per site conditions.

Size 900x900x900 millimetre inside with precast S.F.R.C. grating rectangular of approved design and sample fixed in Plain Cement Concrete 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 millimetre nominal size) including centering, shuttering all complete as per site conditions.

Extra for depth of Catchbasin exceeding 45 centimetre.

Extra for depth of Catchbasin exceeding 60 centimetre.

Extra for depth of Catchbasin exceeding 75 centimetre.

Extra for depth of Catchbasin exceeding 90 centimetre.

Providing and fixing 15centimetre x 10centimetre salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap.

Providing & fixing orange colour safety foot rest of minimum 6 millimetre thick plastic encapsulated as per I.S:10910 on 12 millimetre dia steel bar conforming to I.S:1786 having minimum cross section as 23millimetre x 25millimetre and over all minimum length 263millimetre and width as 165millimetre with minimum 165 millimetre space between protruded legs having 2millimetre tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138millimetre as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacturer's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 centimetre cement concrete block 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20millimetre nominal size) complete as per design.

Providing and installation Supervision, including all civil work of -Grease separator EasyClean ground Standard Model/ Article No.: NS 10_ 93010/120B , 740-1175 mm, class A/B, The separator for greasy wastewater is suitable for installation in the ground and comes without metallic components in the tank. The collecting tank made of permanently resistant polymer (PE) is equipped with an integrated sludge trap and has a rounded base for fast and clean disposal. Access for cleaning and maintenance work is possible via one or several service access covers. Manual disposal is carried out with the tank open. for 1200 to 1700 Meals/Day ( Breakfast + lunch+ Dinner) 20 year polyethylene warranty. Installation situation: underground installation, Type of disposal: manual with suction hose, Disposal variant: Standard, Refill inlet in accordance with DIN 1988: no, Nominal size (NS): 10, Note on installation depth: Installation in the ground, frost-free depth 1200 millimetre, Material: PE, Standard: EN 1825: 2004, DIN 4040-100, Max. length: 3,062 millimetre, Required access area, length: 2,910 millimetre ; width: 1,200 millimetre, Inlet nominal size (OD): 160 millimetre ; Outlet nominal size (OD): 160 millimetre, Distance pipe bottom inlet to tank bottom: 1,100 millimetre ; Distance pipe bottom outlet to tank bottom: 1,030 millimetre, Installation depth: 740 - 1,175 millimetre, Groundwater resistant from lower edge of base section: 1,320 millimetre, Clear width of entry (LW): 600 millimetre, Load class: B 125 (EN 124), Height: 95 millimetre, Tightness: odour-tight and surface water resistant, Separator contents: 1,600 l, Total volume: 2,600 l ; Contents of sludge trap: 1,000 l ; Storage quantity of grease: 400 l

RAIN WATER HARVESTING WELL Construction of rain water harvesting well of 4.5 metre dia and 4.5 metre effective depth with the operation of earth work in excavation and drilling with RC/DC/Calyx rig having 400/450 millimetre dia bore size in all kind of starta except rock, back filling alround harvesting well with available excavated earth, with necessary compaction and shifting of surplus earth outside by mechanical means as directed by the Engineer-In-Charge, PCC 1:5:10 , 200mm thick foundation concrete, brick work in cement mortar 1:4 (1 cement : 4 coarse sand), PVC coated safety steel foot rest of 12 millimetre dia MS bars grouted rigidly in cement concrete 1:2:4 @300 millimetre c/c, 200 millimetre thick RCC tank cover slab in cement concrete M20 i/c providing and placing necessary steel raft, bars and to keep the provision of removable slab of approx. 1metre x1metre size, filling 300millimetre, 300millimetre & 300millimetre thick of 40-65millimetre nominal size graded loose boulders, Gravel 5-10 millimetre size and sand layer respectively, CI vent pipe, (100millimetre dia), 250millimetre dia uPVC slotted pipes 6 Kilogram per square centimetre working pressure, filling around the slotted pipes and packing 3millimetre to 6millimetre sized graded and screened rounded Pea Gravel duly washed fabricating and placing grating at the mouth of pipes, placing 560 millimetre dia SFRC manhole cover with frame etc. i/e all necessary materials and equipments required for all relevant operations as shown in the drawing.

Providing and construction of brick masonry desilting chamber of size 200x100x50centimetre (effective depth) before rainy well with 75 class designation bricks in cement mortar 1:4 (1 cement : 4 coarse sand), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand; 8 graded stone aggregate 40 millimetre nominal size), inside and outside plastering 12millimetre thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement inside and rough plaster on outside, including fixing of grating, neatly finished complete in all respects including 2nos of 560 millimetre dia SFRC manhole with neccessary excavation in all kinds of soils, refilling and disposal of surplus earth, complete. (Shop drawing to be got approved).

PUMPS & EQUIPMENTS Filter Feed pump Supply, Installation, Testing and Comissoning In-line vertical multistage centrifugal pump set (for clear water) SS-304 casing, SS-304 impeller, SS-316 shaft, CI base with coating, complete directly coupled with TEFC induction motor of class "F" insulation & efficiency class IE-5, 2900 RPM, suitable for operation on 415 volts ±10%, 3 phase, 50 Hz, A.C. supply, mechanical seal, pressure gauges with gunmetal isolation cocks, vibration elimination pads etc. mounted on a MS base frame bolted to cement concrete foundation etc. complete in all respects and as per technical speicification for following capacities: No. of Pumps : 3(2W + 1S) Capacity : (30 m3/hr) of Each Pump, Head : 25 metre, Note:-1 set consists of 2 nos. of pumps (2 Working + 1Standby)

Multi grade Filter Supply, Installation, Testing and Commissioning of vertical Multi grade Filter (comprising of minimum 750 millimetre media in four graded layer and minimum Height on Straight 1500 millimetre) fabricated from high performance M.S plate of minimum 10millimetre thick for shell & 12millimetre thick for dished ends,(Quality of Steel as per IS:2062 Grade B),Tested to 5.0 Kilogram per Square Metre , internally treated with coal-tar epoxy, air scouring, collection system initial charge of media, M.S face piping with necessary flanges, gaskets, isolating valves, accessories, nuts & bolts, external painting with 2 coats of red oxide primer and enamel paint etc. with suitable foundation bolts & other accessories, mounting frame, complete as required & as per technical specifications of the following capacities: Discharge : 30 Cubic Metre per Hour Each , Filtration Rate : 17500 Litre per Square Metre per Hour, Dia. : 1.8 metre I.D.

Activated carbon Filter Supply, Installation, Testing and Commissioning of vertical activated carbon Filter (comprising of minimum 750 millimetre media in four graded layer including carbon and anthra cite and minimum Height on Straight 1500 millimetre) fabricated from high performance M.S plate of minimum 10 millimetre thick for shell & 12 millimetre thick for dished ends,(Quality of Steel as per IS:2062 Grade B),Tested to 5.0 Kilogram per square metre , internally treated with coal-tar epoxy, air scouring, collection system initial charge of media, M.S face piping with necessary flanges, gaskets, isolating valves, accessories, nuts & bolts, external painting with 2 coats of red oxide primer and enamel paint etc. with suitable foundation bolts & other accessories, mounting frame, complete as required & as per technical specifications of the following capacities: Discharge : 30 Cubic Metre per Hour Each , Filtration Rate : 17500 Litre per Square Metre per Hour, Dia. : 1.8 metre I.D.

Chlorinator Supply, Installation, Testing and Commissioning chemical dozing system consisting of 2 nos. electronic dosing pumps (1W+1S) with all accessories, suitable to doze chemical solution upto 1 ppm doze of Sodium Hypo-chloride solution to a filtered water flow of 42000 LPH against a pressure of 1.5 Kilogram per Square Centimetre complete with FRP moulded solution holding tank of min. 200 litre with all standard accessories & structural arrangement including suitable foundation bolts & other accessories etc. complete as per technical specifications as required. Note:1 set consists of 2 nos. of pumps(1W+1S)

Hydropneumatics Pumping System With Variable Frequency Drive Supply, Installation, Testing and Commissioning of compact packaged type skid mounted, self-contained variable frequency drive hydropneumatics system complete as per the technical specification complete as required:- (i) In- line vertical multistage centrifugal water pump set (for clear water) with SS-304 casing, SS-304 impeller with SS-316 shaft ,CI base with coating complete directly coupled with TEFC induction motor of class "F" insulation & efficiency class IE-5, 2900rpm, suitable for operation on 415 Volts ±10%, 3 phase, 50 Hz A.C. supply. The entire system shall be mounted on a common base frame i/c common suction and common delivery of G.I heavy class pipe headers with flanges, interconnecting piping with all required Conrol Valves, Non-return valves, pressure guage with isolation cock etc. complete as required. (ii) Pressure vessel of non-corrosive FRP composite construction lined with NSF and/or FDA listed material, like high density polyethylene with fully replaceable polyurethane. Air cell burst pressure of minimum of 3 times the vessel operating pressure and prototype cycle tested for 80,000 cycles with charging connections to discharge pipe line with necessary flanges, gaskets, isolating valve, nuts/ bolts etc. with suitable foundation bolts etc complete as required. (iii) Microprocessor based multi pump controller/panel with graphical display and variable frequency drive (VFD) mounted inside a panel complete with pressure sensor transmitter. The graphical display capable to show number of pumps running & also communicate with other controllers following with open protocol through RS485 port. System should be capable to compensate for frictional losses at lower flows. All alarms should be displayed in the controller. The panel should also have provision for manual / automatic alternate (cyclic) operation of pumps, ON/OFF switch complete as required. (v) Necessary foundationing bolts, vibration elimination pads etc complete as required. Domestic Water Supply Pumps "Duty of each pump suitable for:- No. of Pumps : 3 nos. (2 W + 1 S), Capacity : 30 m3/hr of Each Pump, Head : 60 Meters, Air Vessel : 100 Ltr tank, Note:-1 set consists of 3 nos. of pumps (2 Working + 1Standby)"

Drainage Sump Pump for drainage Supply, installation, testing and commissioning compact Monoblock dry motor sump pumps of suitable rating, with non-clog free flow open impeller, solid handling capacity at least 28 millimetre suitable for operation on 415 volts +10% , 3 Phase, 50Hz, A.C supply, speed 2900 RPM including oil chamber, guide wire for lifting & lowering of pump, G.I. galvanized lifting chain, complete. The above pump sets must be supplied complete with following accessories. GI Piping of 80 millimetre dia for individual pump delivery line and 100millimetre dia for common delivery line, to be terminated outside the sump. 80mm dia Butterfly valve.--3 Nos, 80 millimetre dia reflux valve.-- 3 Nos Electrical switch panel with DOL starter having all necessary accessories & safety devices of standard specifications. Automatic built-up water level controller with necessary length of cable upto control panel. No. of Pumps/set : 3nos. (2 W + 1 S), Discharge - 250 LPM Each, Head - 15 Meters

Supply, installation, testing and commissioning reinforced neoprene rubber vibration eliminators/expansion joints (to provide relief from stresses at pipe flanges) suitable for upto 20 Kilogram per Square centimetre pressure,complete as per specifications as required. 80 Millimetre Diametre

100 Millimetre Diametre

150 Millimetre Diametre

Supply, installation, testing and commissioning of 750 millimetre long hot dipped G.I. Puddle flanges for water tanks as per I.S. 1239 (Class C) with 6 millimetre thick M.S. Plate of suitable size and welded alround the pipe fixed in walls, beams and top slab of R.C.C tanks, complete with all details in all respects and as per drawing and specifications. 50 millimetre diametre

65 millimetre diametre

80 millimetre diametre

100 millimetre diametre

150 millimetre diametre

200 millimetre diametre

250 millimetre diametre

Supply, installation, testing and commissioning of double flanged Water Flow Meter complete with digital display provision & including Pulse generator and Remote Totalizer complete in all respect as per the technical specifications & and should be compatible with BMS. 50 millimetre diametre

65 millimetre diametre

80 millimetre diametre

100 millimetre diametre

Supply, installation, testing and commissioning of insect-proof coupling,to vent pipes of water tank with threaded or flanged joints, including G.I. flanges, nuts, bolts, 3 millimetre thick rubber insertions complete as per technical specifications. 80 millimetre diametre

100 millimetre diametre

Providing and Fixiing extra heavy duty, water tight double sealed Ductile iron Circular Manhole cover and frames specially casted for placing over the UG Water tanks with lifting and locking arrangements as per approved sample, complete in all respect including fixing in PCC as per site Requirement .

Providing and fixing H.D.P container one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres

Pump motor controller cum water level indicating panel Supply, installation, testing and commissioning of Centralised PLC control panel front operated, cubicle construction, wall mounted type, fabricated out of 1.6 mm thick CRCA Sheet, with hinged lockable doors, dust and vermin proof, powder coated of approved shade, inter-connections, having, internal wiring, earth terminals, Top / Bottom control cable entry, numberings etc. comprises of touch-screen display board (Min.Diag. size 8"") along with all accessories for complete Programmable logical controls & indications, having necessary interlocks, Inputs/Outputs, required number of repeater amplifiers, all audio-visual alarms as per the requirements listed below i/c emergency stop push button on the panel etc. The panel shall have BMS compatible Modbus protocol complete as required and as specified." Water level indicators and controllers : The hydrostatic pressure sensor (Water level indicator) is working on hydrostatic pressure measurement principle made of Stainless Steel for installation in storage tanks, and capable of providing 4 to 20 mA analog signal compatible with PLC signal inputs and all control outputs to MCC panel (Plumbing/Water supply),complete as per working requirements for equipment detailed below. Fire Static Underground tanks- 1 No. Real-Time water level indication monitoring, Low Level audio-visual alarm at less than 30% total capacity. Raw Water Underground tanks- 1 No. Real-Time water level indication monitoring, Low Level audio-visual alarm at less than 30% total capacity. High Level audio-visual alarm at more than 100% total capacity. Auto cut-out of raw water pumps at 95 % capacity of domestic tank. Auto cut-in of raw water pumps at 25 % capacity of domestic tank. Auto cut-out of raw water pumps at 10% capacity of raw water tank Domestic Water Underground tanks- 1 No. Real-Time water level indication monitoring. Low Level audio-visual alarm at less than 30% total capacity. High Level audio-visual alarm at more than 100% total capacity.

Providing of ISI Marked multicore PVC insulated and PVC sheathed copper conductor armoured control cable of 1.1 KV grade confirming to IS 1554 (Part-1) as ammended upto date and as specified of following sizes. including necessary support clamps at ceiling level and connection legs complete in all respects as per directions of the engineer-in-charge. 2 core 1.5 Square millimetre

Providing of following sizes of 1.1KV grade XLPE insulated and PVC sheathed copper conductor armoured stranded power cables conforming to IS 1554 (Part-1) & (7098 Part-1) as ammended upto date and as specified, including necessary support clamps at ceiling level, connection lugs and double compression glands, complete in all respects as per directions of the engineer-in-charge. 3 core 2.5 Square Millimetre

3 core 4 Square Millimeter

3 core 6 Square Millimeter

3 core 10 Square Millimeter

3 core 16 Square Millimeter

Providing & Fixing of electric insulated rubber mat non-skid type with grooved top size 1metre x 2metre and 12 Millimeter thick as per IS : 5424 as required suitable for 1100 volts complete as per directions of the engineer-in-charge.

Providing, laying, testing & commissioning of 'C' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts,bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required : 50 millimetre diametre

65 millimetre diametre

80 millimetre diametre

100 millimetre diametre

150 millimetre diametre

Providing, installation, testing and commissioning of Cast Iron Y-strainer fabricated out of 1.6 millimetre thick stainless steel, Grade 304, sheet with 3 millimetre dia holes with stainless steel flange. 80 millimetre Diametre

100 millimetre diametre

150 millimetre diametre

Supplying, fixing, testing and commissioning of butterfly valve of PN 16 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 65 millimetre Diametre

80 millimetre diametre

100 millimetre diametre

150 millimetre diametre

Providing and fixing 50 millimetre diametre gun metal gate valve with C.I. wheel of approved quality (screwed end) :

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to API 594 or as per IS 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 65 millimetre diametre

80 millimetre diametre

100 millimetre diametre

Providing orange colour safety foot rest of minimum 6 millimetre thick plastic encapsulated as per IS : 10910 on 12millimetre dia steel bar conforming to IS : 1786 having minimum cross section as 23 millimetrex25millimetre and over all minimum length 263 millimetre and width as 165 millimetre with minimum 112 millimetre space between protruded legs having 2 millimetre tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 millimetre as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 centimetre cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 millimetre nominal size) complete as per design.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 100 millimetre width X 50 millimetre depth X 1.6 millimetre thickness

150 millimetre width X 50 millimetre depth X 1.6 millimetre thickness

200 millimetre width X 50 millimetre depth X 1.6 millimetre thickness

300 millimetre width X 50 millimetre depth X 1.6 millimetre thickness

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 square millimetre (clamped with 1millimetre thick saddle)

Earthing with G.I. earth plate 600 millimetre X 600 millimetre X 6 millimetre thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 millimetre X 5 millimetre G.I. strip in 40 millimetre dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 millimetre X 5 millimetre G.I. strip on surface or in recess for connections etc. as required.

SEWERAGE TREATMENT PLANT 50 KLD Designing, Preparation of Shop Drawings, Supplying, Erection, Testing, Commissioning, handing over, operation & maintenance up to successful commissioning, including purchase and usage of chemical / consumables for operation and maintenance of all Mechanical, Electrical, and other components including getting approval of successful test results from approved Government pollution & environmental authorities, for Sewage Treatment Plant of 50 kld capacity based on MBBR technology with ultrafiltration system complete in all respects on a Turnkey Basis, as per Tender Document comprising Technical Conditions, Technical Specifications, Data, Drawings etc and any other documents attached with this Tender. (Any item not specifically mentioned in these sections but required for the successful completion including handing over, extended DLP, Operation & Maintenance of the STP shall be included in the Quote by the Contractor.) Turnkey Cost for Designing, Supply, Installation, testing & Commissioning handing over, operation & maintenance upto successful commissioning, including purchase and usage of chemical / consumables for operation and maintenance of all Mechanical & Electrical Equipment, Piping, Valves & Accessories for the Complete Turnkey Sewage Treatment Plant as per approved Hydraulic Calculations, Design and Shop Drawings, as per details given in (but not restricted to) tender documents. ELECTROMECHANICAL EQUIPMENTS Equalization Tank Sewage Pumps: The pump sets shall be supplied with required accessories, valves, fittings, cables etc. & as per specification. Air Blower: Air Blowers of twin-lobe type (air cooled) for continuous service with construction in cast iron casing, supply complete with testing and commissioning etc.as specified and as required. Air Diffusers: Membrane diffusers in High Grade Silicon material (Coarse & Fine Bubble as per requirements) with connections to air piping by threaded means, of tube/disc type as required as per process requirements complete with testing and commissioning etc.as specified and as required consisting of Disc Type for coarse bubbles with approx 5 m3 / hr Minimum Air capacity / throughput per Diffuser and Tube Type for fine bubbles with 9 m3 / hr Minimum Air capacity / throughput per Diffuser Sludge Return / Relift Pump at Tube settler: Centrifugal Sludge Return / Re-lift pumps for the transfer of sludge from tube settler to anoxic complete in all respects and as per specifications. Sludge recirculation pump at MBBR tank: Submersible type sludge recycle pump for nitrate recycle from MBBR to Anoxic complete in all respects and as per specifications. Sludge Loading/Disposal Pump: Screw Type Sludge loading / Disposal pump, complete in all respects and as per specifications. Filter Feed Pumps: In-line vertical multistage centrifugal clear water pump set of approved make, complete in all respects and as per specifications. Hydropneumatics Pumping System With Variable Frequency Drive: Supply, Installation, Testing and Commissioning of compact packaged type skid mounted, self-contained variable frequency drive hydropneumatics system complete as required & as per specifications. (i) Flushing Water Supply Pumps, (ii) Horticulture water supply pumps Dual media Filter: Providing and fixing vertical Dual Media Pressure Filter with suitable foundation bolts & other accessories, mounting frame, complete with testing and commissioning etc.as required & as specified. Activated Carbon Filter: Providing and Fixing of Activated carbon filter as per Manufacturer's standard and testing & commissioning complete. Dosing System: Providing and fixing chemical dozing system at Anoxic tank and for centrifuge of approved make with all standard accessories & structural arrangement including suitable foundation bolts & other accessories etc. complete as required and as specified. Ultrafiltration system skid mounted type with feed pump, Cartridge filter, backwash pump, CIP system, Dosing system, UF membrane, PLC panel, Air compressor, instruments and piping, valves etc. Ozonation system at the clarified water tank complete as per specifications, Agitator/ Hydraulic Mixture for Anoxic tank complete as per specifications, Drainage Sump Pumps: Providing and fixing compact dry motor submersible pumps of suitable rating. The pump sets shall be supplied with required accessories & as per specifications with all accessories and control system. Sludge Handling Mechanism (Centrifuge): Providing and fixing of sludge handling arrangement (Centrifuge bowl type) complete with testing & commissioning as required and as specified. UV for Supply to Flushing, Garden water outlet Line: Providing and installation of Online UV system complete with testing & commissioning as required and as specified. Sludge Trolley: Fabrication and supply of sludge trolley for transport of sludge complete as per requirements as specified. Bio media for MBBR tank and Tube settler complete as per specifications Bar Screens: Providing and fixing manually cleaned Bar Screens, to remove coarse and fine material in the water made up of FRP complete as required and as specified, consisting of coarse screen & fine screen. PIPING AND VALVES ACCESSORIES G.I. Pipe: Providing and fixing heavy duty G.I. pipe confirming to IS. 1239 upto 150 mm and IS 3589 for dia 200 mm and above complete as required & as per specifications. uPVC Threaded Water Pipes: Providing and fixing uPVC threaded water pipes (I.S:4985-2000) Class - 5 (Min. 10 Kg/cm2) complete as required & as per specifications. Butterfly Valves: Providing & fixing butterfly valve of rating PN 16 wafer type, in cast iron body with Ductile Iron disc, EPDM seal, SS single piece shaft, conforming to IS-13095, complete as required and as specified. Ball Valves: Providing and fixing forged brass ball valve having stainless steel/ brass ball tested to 25 kg/cm2 complete as required and as specified. Puddle flanges: Providing & fixing GI hot dipped puddle flanges for the tank complete as per the specifications. Non-Return Valves: Providing & fixing non return valve Dual Plate type, conforming to API-594 or IS 3512, complete as required and as specified. CONSUMABLES FOR OPERATION AND MAINTENANCE Supply & Consumption of Consumables, solutions, chemicals, etc. for STP operation and maintenance upto successful commissioning of STP ELECTRICAL SYSTEM STP Panel: Design, manufacture, supply, installation, testing and commissioning of the STP panel complete as required and as specified. Aluminium Conductor: Supply of sizes of 1.1KV grade XLPE insulated and PVC sheathed aluminium conductor armoured stranded power cables conforming to IS 7098 Part-1 as amended upto date and as specified. Supplying and making of cable end termination with brass single compression gland and Al. lug for PVC insulated and sheathed armoured cables of 1.1 K.V. aluminium conductor as required. Laying and fixing of one number XLPE /PVC insulated and PVC sheathed power of 1.1 KV grade of following sizes on surface or existing cable tray complete as required. Earthing: Earthing with GI earth plate of 600mm x 600mm x 6mm thick, including accessories and providing masonry enclosure including MS cover plate having locking arrangement and watering pipe etc. with charcoal and salt complete as required & as specified. G.I. Strip: Providing and Fixing 25 mm x 5 mm G.I. Strip in 40 mm dia. G.I. pipe from earth electrode complete as required. G.I. Strip on Surface: Providing and Fixing 25 mm x 5 mm G.I. Strip on surface or in recess for earth connection as per specifications complete as required. G.I. Wire: Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. Cable Tray: Fabrication and installation of perforated MS cable tray including horizontal and vertical bends, reducers, tees, cross-members and other accessories as required duly suspended from the ceiling with MS Suspenders and including painting with black synthetic paint as required. Rubber Mat: Providing electric insulated rubber mat non-skid type with grooved top 90 cm wide & 12 mm thk as per IS : 5424 as required suitable for 1100 volts. INSTRUMENTATION EQUIPMENTS & INSTRUMENTATION DETAIL Flow Meter: Electro Magnetic Type (5nos) compatible with BMS. Online monitoring system for PH, BOD, COD and TSS. Energy Meter: -1 No., Pressure Gauges:-1 Lot, Level Sensor-1 Lot, Level Gauges:-1 Lot, TDS Meter (Digital, Microprocessor based): Hand-held -1 No., Ultrasonic Level Transmitter: Range 10 m, mounting: Integral (Tank Top)

Supplying and erecting HMS PVC conduit FRLS grade 20 mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No WG-MA/CC [1-1-7]

Supplying and laying HMS PVC conduit FRLS grade 20 mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC [1-1-8]

Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No WG-MA/CC [1-1-9]

Supplying and laying HMS PVC conduit FRLS grade 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC [1-1-10]

Supplying and erecting HMS PVC conduit FRLS grade 32 mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No WG-MA/CC [1-1-11]

Supplying and laying HMS PVC conduit FRLS grade 32mm dia. with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC [1-1-12]

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 20 mm with accessories on wall/ceiling as per specification No WG-MA/CON. [1-2-6]

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25 mm with accessories on wall/ceiling as per specification No WG-MA/CON. [1-2-7]

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 32 mm with accessories on wall/ceiling as per specification No WG-MA/CON [1-2-8]

Supplying and erecting mains with 2x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No WG-MA/BW [1-3-1]

Supplying and erecting green colour earthing with 1x 1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No WG-MA/BW [1-3-1]

Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No WG-MA/BW [1-3-6]

Supplying and erecting mains with 3x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No WG-MA/BW [1-3-7]

Supplying and erecting mains with 3x6 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No WG-MA/BW [1-3-8]

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete. [1-6-1]

Supplying and erecting modular type switch 16A duly erected on provided plate and box with wiring connections complete. [1-6-2]

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter duly erected on provided plate and box with wiring connections complete. [1-6-10]

Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter duly erected on provided plate and box with wiring connections complete. [1-6-11]

Supplying and erecting modular type T.V. socket single outlet duly erected on provided plate and box with wiring connections complete. [1-6-14]

Supplying and erecting modular type telephone socket one gang with safety shutter duly erected on provided plate and box with wiring connections complete. [1-6-15]

Supplying and erecting modular type computer Jack RJ45 with safety shutter duly erected on provided plate and box with wiring connections complete. [1-6-17]

Supplying and erecting modular type blanking plate one module duly erected on provided plate & box. [1-6-24]

Supplying and erecting PVC Surface modular switch box with double mounting plate for 3 module duly erected. [1-6-28]

Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 module duly erected. [1-6-30]

Point wiring for light/bell concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires modular type switch earthing and required accessories as per specification No WG-PW/CW [1-7-5]

Point wiring for independent plug concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wires modular type switch earthing and required accessories as per specification No WG-PW/SW [1-7-8]

Point wiring for ceiling fan in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire modular type switch earthing and required accessories as per specification No WG-PW/SW [1-7-13]

Secondary point wiring for additional light/ bell point concealed type in min 20 mm FRLS grade PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires with required accessories as per specification No WG-PW/CW [1-7-22]

Wiring for plug on board with Switch socket surface/concealed type copper wiring and earthing and with modular accessories as per specification No WG-PW/CW [1-7-26]

Supplying and erecting 2 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation polyester taped Nylon Rip Cord & grey colour sheathed with FR PVC conforming to ITD specification S/WS 113C laid in provided PVC casing capping/conduit as per specification No. WG-TW [1-8-1]

Supplying and erecting 10 pair 0.5mm dia jelly filled unarmoured telephone copper cable with poly-al laminate moisture barrier laid in provided PVC casing capping/conduit as per specification No. WG-TW [1-8-9]

Supplying and erecting 3m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete. [1-8-21]

Supplying, Erecting and Commissioning of 10 pairs FR junction box with moulded plastic enclosure as per specification no. WG-TW [1-9-11]

Supplying, Erecting and Commissioning of 20 pairs FR junction box with moulded plastic enclosure as per specification no. WG-TW [1-9-12]

Supplying and installing cat-6 cable suitable for networking as per specification no. WG-COC/NC [1-10-1]

Supplying and installing enhanced cat-6 LSZH cable with 4-connector channel Performance test report as per ANSI/TIA-568.2-D suitable for networking complete as per specification. [1-10-4]

Supplying and installing cat-6 armoured cable with ECCS tape suitable for networking as per specification No. WG-COC/NC [1-10-7]

Supplying, fixing, and configuring 8-ports 1 G unmanaged gigabit POE switch erected in provided rack complete. [1-11-1]

Supplying, fixing, and configuring 8-ports managed gigabit Layer-2 switch 10/100/1000 base-T POE smart switch plus 2 SFP erected in provided rack complete. [1-11-2]

Supplying, installing & testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC. [1-12-1]

Supplying and fixing 6U wall mount rack (Dimension-DxWxH – 500x600x367 mm) as per specification No. WG-NAS/RAK [1-12-17]

Supplying and erecting LED square / circular Max. 11 W down lighter/Panel Light having pressure die-cast aluminium housing polystyrene diffuser having system lumens output of Min. 1200 Lumens min. efficacy of 110 lumen/W CRI>80 CCT upto 6500K Beam Angle of 120 deg. max. ripple of 5% THD<10% p.f. >0.95 operating range of 120-270V surge protection of 2.5 kV Life class of 50 000 Hrs. at L70B50 including driver having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. [2-1-3]

Supplying and erecting LED square / circular Max. 18 W down lighter/ Panel Light having pressure die-cast aluminium housing polystyrene diffuser having system lumens output of Min. 2000 Lumens min. efficacy of 110 lumen/W CRI>80 CCT upto 6500K Beam Angle of 120 deg. max. ripple of 5% THD<10% p.f. >0.95 operating range of 120-270V surge protection of 2.5 kV Life class of 50 000 Hrs. at L70B50 including driver having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. [2-1-5]

Supplying and erecting LED Panel Light(600mm X 600mm) Max. 30 W having CRCA powder coated housing polystyrene diffuser having system lumens output of Min. 3600 Lumens min. efficacy of 120 lumen/W CRI>80 CCT upto 6500K Beam Angle of 120 deg. max. ripple of 5% THD<10% p.f. >0.95 operating range of 120-270V surge protection of 2.5 kV Life class of 50 000 Hrs. at L70B50 including driver having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. [2-1-7]

Supplying LED concealed type foot / step light with aluminium body for indoor/outdoor application suitable for 4W-6W LED including driver and erecting by making necessary arrangement / recess in wall to make it flush with surface with 1 year warranty. [2-1-12]

Supplying and erecting bulk head LED fitting max. 10W with high transitivity diffuser with system lumens output of min. 1100 lumens min. efficacy of 110 lumen/W CRI>80 CCT upto 6500K Beam Angle of 120 deg. THD<10% p.f. >0.95 operating range of 140-260V in built surge protection of 2.5 kV Life class of 50 000 Hrs. at L70B50 including driver IP66 IK09 rated on provided PVC Block / wooden board with 3 years warranty. [2-1-15]

Supplying and erecting anodized aluminium corridor / passage / mirror light LED fitting (2 feet) Max. 12W with high transitivity diffuser with min. system lumens output of 1200 lumens min. efficacy of 100 lumen/W CRI>80 CCT upto 6000K Beam Angle of 110 deg. Ripple<5% THD<10% p.f. >0.95 operating range of 200-270V surge protection of 2 kV Life class of 50 000 Hrs. at L70B50 including driver with end caps on provided PVC Block / wooden board with 3 years warranty. [2-1-16]

Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens min. efficacy of 100 lumen/W CRI>80 CCT upto 6000K Beam Angle of 110 deg. Ripple<5% THD<10% p.f. >0.95 operating range of 200-270V surge protection of 2 kV Life class of 50 000 Hrs. at L70B50 including driver with end caps on provided PVC Block / wooden board with 3 years warranty. [2-1-18]

Supplying and erecting integrated LED street light fitting 40 to 50W IP65 & IK08 class having single piece pressure die-cast aluminium housing having system lumens output of Min. 4400 Lumens min. efficacy of 110 lumen/W CRI>70 CCT upto 6500K THD<10% p.f. >0.95 operating range of 140-270V inbuilt surge protection of 10 kV Life class of 50 000 Hrs. at L70B50 including driver complete with 3 Years warranty as per specification No FG-ODF/FLS2. [2-4-4]

Supplying and erecting integrated LED flood light fitting Max. 50W IP65 & IK07 class having pressure die-cast aluminium housing having system lumens output of Min. 5000 Lumens min. efficacy of 100 lumen/W CRI>70 CCT upto 6500K THD<10% p.f. >0.90 operating range of 140-270V inbuilt surge protection of 4 kV Life class of 50 000 Hrs. at L70B50 including driver with U shaped bracket with 3 Years warranty as per specification No FG-ODF/FLS2. [2-4-13]

Supplying and erecting integrated LED flood light fitting Max. 70W IP65 & IK07 class having pressure die-cast aluminium housing having system lumens output of Min. 8400 Lumens min. efficacy of 120 lumen/W CRI>70 CCT upto 6500K THD<10% p.f. >0.90 operating range of 140-270V inbuilt surge protection of 4 kV Life class of 50 000 Hrs. at L70B50 including driver with U shaped bracket with 3 Years warranty as per specification No FG-ODF/FLS2. [2-4-14]

Supplying and erecting integrated LED flood light fitting Max. 100W IP65 & IK07 class having pressure die-cast aluminium housing having system lumens output of Min. 12000 Lumens min. efficacy of 120 lumen/W CRI>70 CCT upto 6500K THD<10% p.f. >0.90 operating range of 140-270V inbuilt surge protection of 4 kV Life class of 50 000 Hrs. at L70B50 including driver with U shaped bracket with 3 Years warranty as per specification No FG-ODF/FLS2. [2-4-15]

Supplying and erecting integrated LED Bollard Cylindrical/Cubical shaped 500mm 8W IP65 & IK10 class having extrusion aluminium housing with polycarbonate diffuser having system lumens output of Min. 800 Lumens min. efficacy of 100 lumen/W CRI>80 CCT upto 6500K THD<10% p.f. >0.90 operating range of 140-240V inbuilt surge protection of 2 kV Life class of 25 000 Hrs. at L50B50 including driver complete with 2 Year warranty as per specification No FG-ODF/FLS2. [2-4-19]

Supplying and erecting integrated LED Post Top 45W IP65 & IK10 class having die cast aluminium housing with UV protected polycarbonate diffuser having system lumens output of Min.4500 Lumens min. efficacy of 100 lumen/W CRI>80 CCT upto 6500K THD<10% p.f. >0.90 operating range of 140-240V inbuilt surge protection of 2 kV Life class of 30 000 Hrs. at L50B50 including driver complete with 2 Year warranty as per specification No FG-ODF/FLS2. [2-4-21]

Supplying and erecting fresh air cum exhaust fan of light duty 250 V A.C. 50 cycles 300mm. 1400 RPM rust proof body & blades wire mesh duly erected complete. [2-10-13]

Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 mm max. energy consumption of 28W having service ratio (CMM/W) of Min. 8 PF>0.9 THD<10% with IR remote control/compatible speed regulator Temperature Rise of Max. 40 deg. C having external mounted control PCB completely erected in position as per specification no. FG-FN/CF [2-10-22]

Supplying, installing, testing and commissioning of single phase 230V 50 Hz 2500 VA digital pure sine wave inverter with backup time of ........ hrs. based on Insulated Gate Bipolar Transistor (IGBT) technology complete as per specification no. AP-INV [3-6-4]

Supplying, installing, testing and commissioning of single phase input & 1 phase output 1 kVA capacity online pure sine wave UPS with backup time of ....... hrs. PWM & IGBT based with 0.8 to unity output pf complete with all protections as per specification no. AP-UPS [3-7-1]

Supplying, installing, testing and commissioning of 10kVA capacity online pure sine wave with backup time of ....... hrs. PWM & IGBT based UPS with 0.9 to unity output pf 3 phase input & 1 phase output complete with all protections as per specification no. AP-UPS [3-7-6]

Supplying and erecting 12V/17Ah -18Ah SMF battery with battery terminal wire duly charged with 12 months warranty complete [3-8-8]

Supplying and erecting 12V/42Ah SMF battery with battery terminal wire duly charged with 24 months warranty complete [3-8-10]

Supplying, erecting and marking SPMCB 6A to 32A C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB [5-3-2]

Supplying, erecting and marking DPMCB 40A to 63A C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB [5-3-8]

Supplying, erecting and marking TPMCB 40A to 63A with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB [5-3-11]

Supplying, erecting and marking FPMCB 40A to 63A with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB [5-3-13]

Supplying and erecting triple pole and neutral distribution board (TPNDB) SPMCB of 4 ways/phase (12 poles) with door 1.2mm thickness surface/flush mounted IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB [5-4-1]

Supplying and erecting triple pole and neutral distribution board (TPNDB) SPMCB of 8 ways / phase (24 poles) with door 1.2mm thickness surface/ flush mounted IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB [5-4-2]

Supplying and erecting single pole and neutral distribution board (SPNDB) with 2 ways for incoming and 6 ways (6 poles) for outgoing SP MCBs with door 1.2mm thickness surface / flush mounted IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB [5-4-8]

Supplying and erecting single pole and neutral distribution board (SPNDB) with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs with door 1.2mm thickness surface / flush mounted IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB [5-4-9]

Supplying and erecting triple pole and neutral distribution board (TPNDB) 3 pole/ 4 pole MCCB as incomer & outgoing SP MCB (12 poles) or TP MCB of 4 ways (12 poles) with door 1.2mm thickness surface/flush mounted on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB1 [5-4-15]

Providing and erecting 3 Pole MCCB 415 V 100A rated short-circuit breaking capacity 25 kA (Ics=100% of Icu) adjustable thermal (overload) setting and fixed magnetic setting with provided leads provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides insulation withstand capacity 800V no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB [5-5-1]

Supplying, fixing, and commissioning 2 pole RCBO 6/10/16/20/25A with overcurrent rated short-circuit breaking capacity (10 kA) and earth leakage protection with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO [5-6-9]

Supplying, fixing, and commissioning 2 pole RCBO 32/40A with overcurrent rated short-circuit breaking capacity (10 kA) and earth leakage protection with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO [5-6-10]

Supplying, installing, testing and commissioning of 11 kV 630A vacuum circuit breaker with internal arc compliance complete erected on provided CC foundation/MS channels/trench etc. as per specification no SW-HTS /VCB [5-9-8]

Supplying and erecting GI sheet 1.6 mm (16 SWG) caution board of size 200 x 150 mm duly painted with red oxide and enamel paint in Marathi Hindi and English erected at position for medium voltage (415 Volt) installation with compliance to IS 2551-1982 [6-1-15]

Supplying and erecting GI sheet 1.6mm (16 SWG) caution board of size 250 x 200 mm duly painted with red oxide and enamel paint in Marathi Hindi and English erected at position for HV/EHV (11000 Volts) installation with compliance to IS 2551-1982 [6-1-16]

Supplying, erecting, testing and commissioning of 11KV HT metering cubical (compact / vertical type) approved by MSEDCL / licensee fabricated with 2 mm (14 SWG) M.S. sheets with supporting angle painted with powder coating / epoxy paint of required shade copper bus bar size 25 x 6 mm heavy duty mechanical lock with counter meter for measuring no of times the opening of meter door top side cover (CT PT cover) interlock with meter door epoxy casted 3 nos. CT having required ratio between 10/5A to 50/5A VA10 or 15 Class 0.5S epoxy casted 3 nos. PT having ratio 11000/V3/110/V3 VA 50 Class 0.5 suitable for provided trivector meter and provision for incoming and outgoing cables complete duly tested by licensee with necessary test certificates and erected on provided plinth/ cc foundation. [6-4-1]

Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 2 core 10 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL [7-1-6]

Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3½ core 35 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL [7-1-16]

Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3½ core 50 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL [7-1-17]

Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3½ core 95 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL [7-1-19]

Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3½ core 150 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL [7-1-21]

Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3½ core 185 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL [7-1-22]

Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3½core 240 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL [7-1-23]

Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3½ core 300 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL [7-1-24]

Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 4 core 10 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL [7-1-28]

Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 4 core 16 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL [7-1-29]

Supplying, erecting & terminating Supplying erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL [7-1-30]

Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3 core 2.5 sq. mm. copper conductor complete erected with glands & lugs on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU [7-2-14]

Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3 core 4 sq. mm. copper conductor complete erected with glands & lugs on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU [7-2-15]

Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 3 core 10 sq. mm. copper conductor complete erected with glands & lugs on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU [7-2-17]

Supplying, erecting & terminating FR XLPE insulated galvanised steel formed wire armoured (strip) cable 1100 V 4 core 6 sq. mm. copper conductor complete erected with glands & lugs on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU [7-2-32]

Supplying, erecting & terminating XLPE insulated galvanised steel formed wire armoured (strip) cable 11 kV(E) 3 x 240 sq. mm. aluminium conductor laid in provided trench / pipe as per specification no. CB-HT [7-3-6]

Providing and erecting epoxy outdoor / indoor end termination kit for LT XLPE armoured cable 2.5 to 16 sq mm. with necessary material as per specification No. CB-JT/LT [7-4-8]

Providing and erecting epoxy outdoor / indoor end termination kit for LT XLPE armoured cable 25 to 50 sq mm. with necessary material as per specification No. CB-JT/LT [7-4-9]

Providing and erecting epoxy outdoor / indoor end termination kit for LT XLPE armoured cable 70 to 120 sq mm. with necessary material as per specification No. CB-JT/LT [7-4-10]

Providing and erecting epoxy outdoor / indoor end termination kit for LT XLPE armoured cable 240 to 300 sq mm. with necessary material as per specification no. CB-JT/LT [7-4-12]

Providing and erecting Heat shrinkable indoor termination kit for 11 kV ( E ) XLPE HT cable 3x240 to 300 sq. mm. with necessary material as per specification no. CB-JT/HT [7-5-3]

Supplying and laying (including excavation) reinforced cement concrete pipe of IS 458 2003 NP-2 class of 150 mm internal diameter in proper line level and slope including providing and fixing collars in cement mortar 1 2 and curing etc. complete. [7-6-5]

Supplying and laying (including excavation) reinforced cement concrete pipe of IS 458 2003 NP-2 class of 250 mm internal diameter in proper line level and slope including providing and fixing collars in cement mortar 1 2 and curing etc. complete. [7-6-7]

Supplying and laying (including excavation) of suitable width & depth up to 90 cm) 75 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface to required depth complete. [7-6-10]

Supplying and laying (including excavation) of suitable width & depth up to 90 cm) 90 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface to required depth complete. [7-6-11]

Supplying and laying (including excavation) of suitable width & depth up to 90 cm) 160 mm outside dia double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface to required depth complete. [7-6-14]

Providing and erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware. [7-11-6]

Providing and erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware. [7-11-8]

Providing and erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 500 mm width & 75 mm height complete with necessary coupler plates & hardware. [7-11-10]

Providing and erecting hot dipped galvanised cover suitable for perforated type Cable tray manufactured from 18 SWG (1.2 mm thick) GI sheet of 150 mm width & 20 mm height complete with necessary hardware. [7-11-11]

Providing and erecting hot dipped galvanised cover suitable for perforated type Cable tray manufactured from 18 SWG (1.2 mm thick) GI sheet of 300 mm width & 20 mm height complete with necessary hardware. [7-11-13]

Supplying and erecting 9m (clear height) Fixed type high-mast (Top-100mm Bottom- 200mm) with hexagonal /round bracket and foundation bolts suitable for max. 4 nos. flood light fixtures on provided foundation as per specification no. OH-PL/OPL (excluding luminaires). [8-2-8]

Providing and erecting 3 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL [8-2-9]

Providing and erecting 6 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL [8-2-12]

Providing and erecting 9 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 155 mm A/F top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL [8-2-16]

Providing and erecting galvanised 1000mm single arm sword type bracket with FRP dome and ball as per specification no. OH-PL/PBKT [8-2-21]

Providing and erecting galvanised 1000mm double arm sword type bracket with FRP dome and ball as per specification no. OH-PL/PBKT [8-2-22]

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover complete with all materials testing & recording the results as per specification no. EA-EP [9-1-3]

Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP [9-1-4]

Supplying, installing & testing maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete and recording the results Specification no. EA-MOBI [9-1-5]

Providing earthing with copper earth plate size 60 x 60 x 0.315 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover with minimum 25 kg Carbon based environment friendly back fill Ground Enhancing compound complete with all materials testing & recording the results as per specification no ESE -LA [9-1-6]

Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP. [9-2-3]

Supplying and erecting GI wire of high purity of required sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/ conduit with screws complete. [9-2-5]

Supplying and erecting copper strip of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with insulating and non-corrosive bond with required joints As per specification no. EA-EP. [9-2-7]

Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with insulating and non-corrosive bond with required joints As per specification no. EA-EP. [9-2-8]

Supplying, installing, testing and commissioning of 3 phase 11/0.433 kV 50 Hz. 630 kVA Mineral oil immersed and naturally cooled outdoor type Copper wound Non-sealed transformer delta/star connected additional neutral brought out on load side temperature rise should not exceed 45? by thermometer in oil and 50? by the resistance method in winding at full load rating using type A winding insulation (kraft paper) with HV tapping (with off load tap changer) off load +5 to -10 in steps of 2.5% having 7 number of tap positions with standard accessories complete with test certificate with losses below 1860 Watts at 50% load 5300 Watts at 100% load as per IS 1180 (part 1) 2014 with necessary permissions of Electrical Inspector as per specification no SS- TR-NSL. [10-1-10]

Providing printed instruction chart for treating persons suffering from electric shock printed in English & Marathi and duly laminated complete. [10-6-22]

Providing pair of duly tested rubber hand gloves as per IS 47705 suitable for working up to 22 kV supply complete. [10-6-23]

Supplying standard first aid box with necessary antiseptic cream medicine for use on wounds due burn crepe bandage gauge bandage medicated ready to use bandage (Band-Aid) adhesive tape for medicinal use scissors anti-septic solution etc. (All above contents shall be of standard makes) [10-6-24]

Supplying and fixing PVC synthetic elastomer electrically insulating mat with class A insulation conforming to IS 15652 – 2006 having 2 mm thickness up to 3.3 kV [10-6-25]

Supplying and fixing PVC synthetic elastomer electrically insulating mat with class B insulation conforming to IS 15652 – 2006 having 2.5 mm thickness up to 11 kV [10-6-26]

Supplying, erecting, testing and commissioning of diesel generating set with alternator of 125 kVA output continuous rating 3 Phase 415 V 50c/s 0.8 p. f. A.C supply a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours along with standard accessories self-excited self-regulated screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 % with performance class G2 and maximum fuel consumption 21.4 Ltr/hr 75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters switchgears indicators connected with suitable wires/cables the complete set enclosed in composite Acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet sound absorbing material to restrict sound level up to 75 dB at 1.0 m provided with first filling of oil diesel not less than 230 Ltr etc. on provided M20 Grade CC Foundation as per specification no. GEN-DG [11-1-13]

Supplying, erecting, testing and commissioning of diesel generating set with alternator of 250 kVA output continuous rating 3 Phase 415 V 50c/s 0.8 p. f. A.C supply a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours along with standard accessories self-excited self-regulated screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 % with performance class G2 and maximum fuel consumption 42.30 Ltr/hr 75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters switchgears indicators connected with suitable wires/cables the complete set enclosed in composite Acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet sound absorbing material to restrict sound level up to 75 dB at 1.0 m provided with first filling of oil diesel not less than 425 Ltr etc. on provided M20 Grade CC Foundation and obtaining necessary approval from Electrical Inspector as per specification no. GEN-DG [11-1-18]

Supplying, erecting, testing and commissioning of microprocessor based AMF panel suitable for diesel generating set of above 125 kVA up to 140 kVA capacity Three phase 415 Volts 50Hz A.C. with all standard features safeties etc as per specification no. GEN-AMF. [11-2-12]

Supplying and erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete. [13-15-1]

Main LT Panel - (I/C from6 630 KVA Transformer) Transformer Incomer : 1000A, FP MDO type ACB (50 KA) with microprocessor based O/L, S/C and E/F releases. Metering, Indication & Protection: (1 Set) 1 No. Multifunction digital meter (consisting of Voltage, Current, Frequency, PF, kWh, kVA THD parameter) analyzer with RS-485 Port. 1 No. of 1000/5A, CL-1, 10VA measuring CTs. 1 No. of phase indicating lamps with MCB. 1 No. of ON/OFF/Trip/Trip circuit healthy/ready to close lamps. 1 No. 1000/5A, CL-1, 10VA CT for APFCR. 1 No. of restricted earth fault relay with 1000/5A, CL-PS, CTs (3 Nos. to be mounted in panel and 1 No. to be supplied loose). 1 No. of Voltage Transformer 415/110V AC, 100VA with control MCBs. Under voltage relay (27), Over voltage relay(59), Trip circuit supervision relay(TCSR) Master trip lockout relay(86), Surge Arrestor complete in all respect as required. BUSBAR "Electrolytic high conductivity aluminium three phase and neutral busbars having a maximum current density of 1 amp per sq mm suitable to with stand symmetrical fault level of 35 kA at 415 volts. The neutral busbar is to be of 50% capacity. Busbar1000 AMP", OUTGOING Note : Each outgoing feeder shall have 1 set of ON/OFF indicating lamps, 3 nos Cast resin type Class 1.0, 15 VA Burden CT's for metering. CT Ratio as per breaker rating, Digital electronic ammeter, 1 No. 630 Amp TPN MCCB, 25 KA. 1 No. 400 Amp TPN MCCB, 25 KA. 3 No. 300Amp TPN MCCB, 25 KA.,

SDB COMMERCIAL INCOMING : 1 no. 200 Amps, 690 volt 25 KA, 4 pole MCCB each complete with microprocessor base overcurrent, earth fault releases. The MCCB shall be provided with microprocessor based release having variable range of over current, short circuit and earth fault protection with time lag facility for each of the fault for achieving discrimination. BUSBAR "Electrolytic high conductivity aluminium three phase and neutral busbars having a maximum current density of 1 amp per sq mm suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity. Busbar-250 AMP", OUTGOING Note : Each outgoing feeder shall have 1 set of ON/OFF indicating lamps, 3 nos Cast resin type Class 1.0, 15 VA Burden CT's for metering. CT Ratio as per breaker rating, Digital electronic ammeter, 3 No. 100 Amp TPN MCCB, 16 KA.

SDB COMMON AREA INCOMING1 (400 KVA) : 1 No. 630A, FP EDO type ACB (50 KA) with microprocessor based O/L, S/C and E/F releases. Metering, Indication & Protection: Microprocessor release having inbuilt overload protection with time delay, short circuit protection with time delay, instantaneous alongwith earthfault protection. 1 no.Multi function Meter (MFM) with RS 485 port of 1.0 accuracy to measure voltage, current, power factor, frequency, KW , KVA, KWH, KVAh with required CT. 6 nos NO/NC contacts for remote opening & closing, ON/OFF/TRIP indicating lamps, 1 set of three White phase indicating lamps (RYB), Under voltage & Over voltage relay, Terminals to receive XLPE Cables INCOMING 2 (125 KVA) : 1 nos 200 Amps 690 volt 4-P MCCB, 35 kA & 200A, 4-P AC-III Contactor complete with Microprocessor release having inbuilt overload protection with time delay, short circuit protection with time delay, instantaneous alongwith earthfault protection.. Metering, Indication & Protection: Microprocessor release having inbuilt overload protection with time delay, short circuit protection with time delay, instantaneous alongwith earthfault protection. 1 no.Multi function Meter (MFM) with RS 485 port of 1.0 accuracy to measure voltage, current, power factor, frequency, KW , KVA, KWH, KVAh with required CT. 6 nos NO/NC contacts for remote opening & closing, ON/OFF/TRIP indicating lamps, 1 set of three White phase indicating lamps (RYB), Under voltage & Over voltage relay, Terminals to receive XLPE Cables INCOMING -3 ( From Main LT Panel) 630A, FP EDO type ACB (50 KA) with microprocessor based O/L, S/C and E/F releases. Metering, Indication & Protection: Microprocessor release having inbuilt overload protection with time delay, short circuit protection with time delay, instantaneous alongwith earthfault protection. 1 no.Multi function Meter (MFM) with RS 485 port of 1.0 accuracy to measure voltage, current, power factor, frequency, KW , KVA, KWH, KVAh with required CT. 6 nos NO/NC contacts for remote opening & closing, ON/OFF/TRIP indicating lamps, 1 set of three White phase indicating lamps (RYB), Terminals to receive XLPE Cables BUSBAR "Electrolytic high conductivity aluminium three phase and neutral busbars having a maximum current density of 1 amp per sq mm suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity. Busbar-800 AMP", 3 nos Cast resin current transformers of 800/5 ratio Class 1.0 for metering BUS COUPLER : 1 nos 200 Amps 690 volt 4-P MCCB, 35 kA with thermal magnetic release having overcurrent ,short circuit protection & 200A, 4-P AC-III Contactor complete with 6 nos NO/NC contacts, Red/Green/amber ON/OFF/spring charge indicating lamps OUTGOING Note : Each outgoing feeder shall have 1 set of ON/OFF indicating lamps, 3 nos Cast resin type Class 1.0, 15 VA Burden CT's for metering. CT Ratio as per breaker rating, Digital electronic ammeter, 7 No. 63 Amp TPN MCCB, 25 KA. 2 No. 100 Amp TPN MCCB, 25 KA. 2 No. 250 Amp TPN MCCB, 25 KA. 1 No. 400 Amp TPN MCCB, 25 KA.

CAPACITOR SWITCHBOARDS-200 kVAR INCOMING- Direct cable connection to the Busbars, 3 nos Cast resin current transformers of 400/5 ratio Class 1.0 for metering, Digital electronic ammeter , 1 set of three White phase indicating lamps Terminals to receive XLPE cables, 16 step automatic power factor correction relay to sense and monitor the system power factor and provide impulses for operation of 14 capacitor circuits as below. BUSBARS- Electrolytic high conductivity aluminium three phase busbars rated at 300 amps having a maximum current density of 1 amp per sq mm suitable to with stand symmetrical fault level of 35 KA at 415 volts. OUTGOINGS – 3No. - 160 amp 25 KA TP MCCB each with 3 pole capacitor grade contactor suitable for automatic switching of 50 kVAR capacitor bank with 14% detuned reactors, On/Off Indicating lamp, On/Off Push Button, Manual/auto changeover switch, 50 kVAR hermetically sealed metallized polypropylene capacitor units complete with fuse protection, discharge resistors, interconnections etc complete as required. 5 Nos. - 63 amp 25 KA TP MCCB complete each with 3 pole capacitor grade contactor suitable for automatic switching of 25 kVAR capacitor bank with 14% detuned reactors, On/Off Indicating lamp, On/Off Push Button, Manual/auto changeover switch, 25 kVAR hermetically sealed metallized polypropylene capacitor units complete with fuse protection, discharge resistors, interconnections etc complete as required. 1No- 40 amp 25 KA TP MCCB complete each with 3 pole capacitor grade contactor suitable for automatic switching of 15 kVAR capacitor bank with 14% detuned reactors, On/Off Indicating lamp, On/Off Push Button, Manual/auto changeover switch, 15 kVAr hermetically sealed metallized polypropylene capacitor units complete with fuse protection, discharge resistors, interconnections etc complete as required., 2No. - 25 amp 25 KA TP MCCB complete each with the following, 3 pole capacitor grade contactor suitable for automatic switching of 5 kVAR capacitor bank with 14% detuned reactors, On/Off Indicating lamp, On/Off Push Button, Manual/auto changeover switch, 5 kVAr hermetically sealed metallized polypropylene capacitor units complete with fuse protection, discharge resistors, interconnections etc complete as required. The Switchboard shall be complete with all interconnections, risers, internal wiring, labels etc. complete as required

SDB - Tree of Life INCOMING : 1 No. 100A, TPN MCCB, 16 KA. Metering : Incomer feeder shall have 1 set of ON/OFF indicating lamps, 3 nos Cast resin type Class 1.0, 15 VA Burden CT's for metering. CT Ratio as per breaker rating, Digital electronic ammeter & Volt meter. BUSBAR "Electrolytic high conductivity aluminium three phase and neutral busbars having a maximum current density of 1 amp per sq mm suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity. Busbar-200 AMP", OUTGOING 2 No. 40 Amp TPN MCB, 10KA 2 No. 20 Amp DP MCB, 10KA

Laser & Fountain Panel INCOMING : 1 no. 400 Amps, 690 volt 25 KA, 4 pole MCCB each complete with microprocessor base overcurrent, earth fault releases. The MCCB shall be provided with microprocessor based release having variable range of over current, short circuit and earth fault protection with time lag facility for each of the fault for achieving discrimination. Metering : Incomer feeder shall have 1 set of ON/OFF indicating lamps, 3 nos Cast resin type Class 1.0, 15 VA Burden CT's for metering. CT Ratio as per breaker rating, Digital electronic ammeter & Volt meter. BUSBAR "Electrolytic high conductivity aluminium three phase and neutral busbars having a maximum current density of 1 amp per sq mm suitable to with stand symmetrical fault level of 25 kA at 415 volts. The neutral busbar is to be of 50% capacity. Busbar-500 AMP", OUTGOING 1 No. 320 Amp TPN MCCB, 25 KA 2 No. 63 Amp TPN MCB, 10KA

Meter Board -1 ( Normal Supply) INCOMING : 1 No. 100A, TPN MCCB, 16 KA. BUSBAR "Electrolytic high conductivity aluminium three phase and neutral busbars having a maximum current density of 1 amp per sq mm suitable to with stand symmetrical fault level of 25 kA at 415 volts. Busbar-200 AMP OUTGOING Note : Each outgoing feeder shall have 1 set of ON/OFF indicating lamps, 3 nos Cast resin type Class 1.0, 15 VA Burden CT's for metering. CT Ratio as per breaker rating, Digital electronic ammeter, 13 No. 40Amp DP RCBO, 10 KA. 13 No. 0-30Amp Base mounted single phase KWH Meter

Meter Board -1 (DG Supply) INCOMING : 1 No. 100A, TPN MCCB, 16 KA. BUSBAR "Electrolytic high conductivity aluminium three phase and neutral busbars having a maximum current density of 1 amp per sq mm suitable to with stand symmetrical fault level of 25 kA at 415 volts. Busbar-200 AMP OUTGOING Note : Each outgoing feeder shall have 1 set of ON/OFF indicating lamps, 3 nos Cast resin type Class 1.0, 15 VA Burden CT's for metering. CT Ratio as per breaker rating, Digital electronic ammeter, 13 No. 0-30Amp Panel mounted single phase KWH Meter 13 No. 63 Amp on load DP Auto Changeover over . 13 No. 63 Amp DP RCBO, 10 KA.

Meter Board -2 ( Normal Supply) INCOMING : 1 No. 100A, TPN MCCB, 16 KA. BUSBAR "Electrolytic high conductivity aluminium three phase and neutral busbars having a maximum current density of 1 amp per sq mm suitable to with stand symmetrical fault level of 25 kA at 415 volts. Busbar-200 AMP OUTGOING Note : Each outgoing feeder shall have 1 set of ON/OFF indicating lamps, 3 nos Cast resin type Class 1.0, 15 VA Burden CT's for metering. CT Ratio as per breaker rating, Digital electronic ammeter, 5 No. 40 Amp FP RCBO, 10 KA. 5 No. 0-30Amp Base mounted three phase foure wire KWH Meter

Meter Board -2 (DG Supply)- For Retail INCOMING : 1 No. 100A, TPN MCCB, 16 KA. BUSBAR "Electrolytic high conductivity aluminium three phase and neutral busbars having a maximum current density of 1 amp per sq mm suitable to with stand symmetrical fault level of 25 kA at 415 volts. Busbar-200 AMP OUTGOING Note : Each outgoing feeder shall have 1 set of ON/OFF indicating lamps, 3 nos Cast resin type Class 1.0, 15 VA Burden CT's for metering. CT Ratio as per breaker rating, Digital electronic ammeter, 5 No. 0-30Amp Panel mounted three phase KWH Meter 5 No. 40 Amp on load FP Auto Changeover over . 5 No. 40 Amp FP RCBO, 10 KA.

Fire Suppression Automatic Fire Extinguisher for Electrical Panel - Automatic Direct Low Pressure Fire Suppression. Extinguisher and Valve for fowing Electrical Panel with Clean Agent NOVEC-1230 type fire extinguisher of 2 Kgs with End of Line Adaptor with Pressure Gauge to monitor Pressure in the tube, Tube Attachment for UL Listed Fire Detection Tube, UL Listed Fire Detection Tube for automatic fire suppression system, Pressure Switch shall be given with Cylinder and it shall be connected to Master Control Unit with A/V Alarm for indication while activation of system, Mounting Brackets and Triangle type Auto Glow fire extinguisher sign board etc.complete confirming to IS Standards and as per technical specification with all mounting accessories complete as required. Fire extinguisher and required connectors and associated Tube of required Length. UL Listed Fire Detection Tube and accessories connection from cylinder to the inside of the panel. Main LT Panel Main LT Panel (for Panel Size : Refer Single Line Diagram)

Fire Suppression Automatic Fire Extinguisher for Electrical Panel - Automatic Direct Low Pressure Fire Suppression. Extinguisher and Valve for fowing Electrical Panel with Clean Agent NOVEC-1230 type fire extinguisher of 2 Kgs with End of Line Adaptor with Pressure Gauge to monitor Pressure in the tube, Tube Attachment for UL Listed Fire Detection Tube, UL Listed Fire Detection Tube for automatic fire suppression system, Pressure Switch shall be given with Cylinder and it shall be connected to Master Control Unit with A/V Alarm for indication while activation of system, Mounting Brackets and Triangle type Auto Glow fire extinguisher sign board etc.complete confirming to IS Standards and as per technical specification with all mounting accessories complete as required. Fire extinguisher and required connectors and associated Tube of required Length. UL Listed Fire Detection Tube and accessories connection from cylinder to the inside of the panel. SDB Common Area (for Panel Size : Refer Single Line Diagram)

Providing of set of 4 Nos. 9.5 Litre capacity GI bucket painted in post office red colour with prior coat of red - oxide paint and written with white paint 'Fire' and mounted on MS angle iron frame with bracket of appropriate size and capacity including filling sand etc.

SUPPLY & INSTALLATION OF EXTERNAL LIGHT FIXTURES 8 Watt Up Lighters, polyester coated aluminium, suitable for housed in ground/ bushlight. (Make- Wipro, Model No. :Gardenia LF05-600-036-27-XX or equivalent in Crompton/ Havells)

7 Watt COB Spike Light, suitable for outdoor application (Make- Wipro, Model No. : Garnet D930727 or equivalent in Crompton/ Havells)

450 Watt LED flood light IP66 luminaire with aluminum die-cast housing, toughened glass, and unique lens system, for enhanced illumination with inbuilt complete assembly LED driver having high efficacy (Make- Wipro, Model No. : LF20-622-060-57-G3)

LED Strip Light with with ALUMINIUM AND SILICON caseing (Make : Usha Tisva, Model : LUMELACE LED SP 50W 3K 24V120L 5MTR IP65+Driver+Profile)

Control Cable Supplying, laying, testing & commissioning of following 1100 volt grade XLPE insulated PVC sheathed Aluminium/Copper conductor armoured/Unarmored cables as per specification in cable trays / ducts clamped to wall with suitable clamps including, saddles fixing bolts, connecting testing and commissioning complete in all respect as required as per site conditions. 12 core 2.5 sq.mm shielded Cu. Cable

Control Cable Supplying, laying, testing & commissioning of following 1100 volt grade XLPE insulated PVC sheathed Aluminium/Copper conductor armoured/Unarmored cables as per specification in cable trays / ducts clamped to wall with suitable clamps including, saddles fixing bolts, connecting testing and commissioning complete in all respect as required as per site conditions. 4 core 2.5 sq.mm Cu Cable

Supplying and making Cable end termination of the following XLPE insulated PVC sheathed copper conductor armoured cables of 1100 volt grade including supplying and fixing of Copper crimping lugs, double compression glands with earthing testing and commissioning complete in all respect as required as per site conditions.4 core 2.5 sq.mm Cu arm.

Supplying and making Cable end termination of the following XLPE insulated PVC sheathed copper conductor armoured cables of 1100 volt grade including supplying and fixing of Copper crimping lugs, double compression glands with earthing testing and commissioning complete in all respect as required as per site conditions.12 core 2.5 sq.mm Cu arm.

20W LED recessed COB light (size 110mm DIA) 4000k Recess mounted square LED COB downlighter with 2080 lumens output. Aluminium die cast construction with white powder coating. High efficiency reflector optics.Effective thermal management using aluminium casting. Constant current driver

20W LED recessed COB light (size 120x120mm) 4000k Recess mounted square LED COB downlighter with 2080 lumens output. Aluminium die cast construction with white powder coating. High efficiency reflector optics.Effective thermal management using aluminium casting. Constant current driver

2x20W LED recessed COB light (combined size 230x120mm) 4000k Recess mounted square LED COB downlighter with 2080 lumens output. Aluminium die cast construction with white powder coating. High efficiency reflector optics.Effective thermal management using aluminium casting. Constant current driver with 3 years warranty

Recess mounted adjustable LED COB downlighter (track light) track mounted LED COB downlighter with 100lumen per watt output. Aluminium die cast construction with white powder coating. High efficiency reflector optics.Effective thermal management using aluminium casting. Constant current driver with 3 years warranty

1 Mtr. length Single phase track suitable to mount track light

2 Mtr. length Single phase track suitable to mount track light

Supplying and erecting Energy Saving HVLS Fan with 52 Pole & PMSM Motor 230 V A.C. 50 cycles 4800mm dia with required regulator for speed control.

Supplying and erecting Energy Saving HVLS Fan with 52 Pole & PMSM Motor 230 V A.C. 50 cycles 3600mm dia with required regulator for speed control.

Providing and fixing lightening conductor system comprising of erecting Air-Termination consisting of tubular copper rod of 25mm dia. 1.2 mm thick with multiple points head 1.2 mt. long ( Heavy Duty) welded or clamped to G.I. pipe pole B grade 50 mm diaof requiired length with M.S. round bnase plate 25 Cm diam and 10mm thick at bottom embeded in cement concrete 1:3:6 dfoundation of size 45 cm diam x 45 cm Height and providing earthing with copper earth plate of size 60 x 60 x 0.3 cms with cadmium plated nut bolts to fix earthing strip burried in specially prepared earth pits 1.5 metre below ground level with 40Kilogramcharcoal and salt with altemate layers of charcoal and salt and G.I.pipe 40mm dia 2 meter length burried in earthe upto earthling plate remining portion above ground level for watering and refilling comcpete Note- Copper strip fropm lightening conductor is not considered in this item.

Providing and fixing copper strip 25mm wide and 3mm thick for lightening conductor including fixing with screws required scaffolding etc.complete Note- Lightening conductor and earthinf pits is not considered in this item

Supplying & erecting of High definition 4/5 Megapixel IP IR Dome Camera with following features Image Sensor Minimum 1/2.8 Progressive Scan CMOS Video Resolution Minimum 2592 x 1520 Video Compression H.264 H.265 or higher at least Three individually configurable stream Frame rate Minimum 25 fps at all resolutions WDR minimum 120 dB Wide Dynamic Range ONVIF profile conformant Minimum IR distance 50m Lens Type 2.8/4/6 mm Lens fixed focal Field of View 2.8 mm horizontal FOV 107° vertical FOV 57° diagonal FOV 129° 4 mm horizontal FOV 86° vertical FOV 47° diagonal FOV 102° 6 mm horizontal FOV 55° vertical FOV 29° diagonal FOV 65° Lux sensitivity - Minimum 0.2 Lux at color Minimum 0.05 Lux at Black & White 0.0 Lux (IR) Night Vision Distance Minimum IR - 50m. Camera minimum Adjustment Angles - Pan 350° Tilt 72° Rotate 350°. Power Supply Support 12VDC & PoE IP67 IK10 - Vandal Resistant. Built in micro SD/SDHC/SDXC card slot of Minimum 128 GB Built in microphone. Minimum Input/Output - Audio in × 1 Audio Out × 1 Alarm in × 1 Alarm Out × 1. RoHS WEEE ISO-14001 and REACH compliant UL/EN OR equivalent BIS/TECH/STQC or any indian standards as applicable CE FCC certified. duly erected in position on wall/ceiling/false ceiling/provided pole (mounting height not more than 5 meter) etc with all accessories etc complete as per specification no. CCTV. (Non-CSR)

Supplying, installing, testing & commissioning of 32/40 Ch. Network Video Recorder (NVR), suitable connect Min. 32 IP Cameras, up to 5 Megapixel Resolution, with HDMI/VGA outputs, provided HDMI output of 4K resolution or VGA output with output up to 1920 × 1080. Support H.265 or higher, H.264, MJPEG, Incoming Bandwidth 250Mbps with minimum 4 SATA Hard Disks, ANR Technology, 4 SATA interfaces for 4 HDDs and capacity of each HDD up to 8TB, minimum 02 USB port, Alarm I/O 16/4, RJ-45 10/100/ 1000 Mbps self-adaptive Ethernet interface, ONVIF conformance, Multiple network monitoring: Web viewer . support protocol TCP/IP, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS. RoHS, UL, CE, FCC certified.duly erected in provided U Rack with wiring connections, tagging and programming etc. complete as per specification no. CCTV-NVR(Non-CSR)

Supplying & erecting 8 TB internal Surveillance HDD suitable for SATA Port of NVR, interface transfer rate 6 GB/S, Maximum sustained transfer rate 210 MB/Sec to 213 MB/S. Drive bay supported 08+, Cameras supported up to 64, Cache (MB) 256, Load/Unload Cycle -3000000, Work Load Rating per Year 180TB, MTBF 1000000 Hrs. HTTPS. RoHS, UL, CE certified, duly erected in position in provided NVR as per specifications CCTV-HDD(Non-CSR)

Supplying & erecting 43" professional LED display with 1920*1080 (Full HD) Display, suitable for 16/32 channel NVR and following features Brightness: minimum 500 Cd/m2 Contrast Ratio: minimum 1000:1 Viewing angle: 178/178 deg. Response time: maximum 8 ms Inputs: HDMI, VGA, BNC,USB, Audio In, Built-in speakers maximum 10 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. CCTV-MON(Non-CSR)

Supplying & erecting of High definition 4/5 Megapixel IP IR Bullet Camera with following features Image Sensor Minimum 1/2.8 Progressive Scan CMOS Video Resolution Minimum 2592 x 1520 Video Compression H.264 H.265 or higher at least Three individually configurable stream Frame rate Minimum 25 fps at all resolutions WDR minimum 120 dB Wide Dynamic Range ONVIF profile conformant Minimum IR distance 50m Lens Type 2.8/4/6 mm Lens fixed focal Field of View 2.8 mm horizontal FOV 107° vertical FOV 57° diagonal FOV 129° 4 mm horizontal FOV 86° vertical FOV 47° diagonal FOV 102° 6 mm horizontal FOV 55° vertical FOV 29° diagonal FOV 65° Lux sensitivity - Minimum 0.2 Lux at color Minimum 0.05 Lux at Black & White 0.0 Lux (IR) Night Vision Distance Minimum IR - 50m. Camera minimum Adjustment Angles - Pan 350° Tilt 72° Rotate 350°. Power Supply Support 12VDC & PoE IP67 IK10 - Vandal Resistant. Built in micro SD/SDHC/SDXC card slot of Minimum 128 GB Built in microphone. Minimum Input/Output - Audio in × 1 Audio Out × 1 Alarm in × 1 Alarm Out × 1. RoHS WEEE ISO-14001 and REACH compliant UL/EN OR equivalent BIS/TECH/STQC or any indian standards as applicable CE FCC certified. duly erected in position on wall/ceiling/false ceiling/provided pole (mounting height not more than 5 meter) etc with all accessories etc complete as per specification no. CCTV-CCTV(Non-CSR)

Supply, installation and commissioning of Remote compact keyboard, variable speed, USB Joystick Control, for PTZ camera/NVR, UL Listed.

Supply, installation, testing & commissioning of fully Loaded 12 port LIU with all reqd. patch cords, pigtails, splicing and other devices/ accessories required to complete the system/ network.

Supply, installation, testing & commissioning of IP66 Box ( 600 X 400 mm) with bottom lowers for heat dissipation for housing Switches, media converter, power supply units for camera connecting over fiber optics( 2 cameras connected to 1 outdoor box).

Supply, installation, testing & commissioning of IP66 Box ( 360 X 260 X 80 mm) with bottom lowers for heat dissipation for housing media converter, power supply units for camera connecting over fiber optics( 2 cameras connected to 1 outdoor box).

Supply, installation, testing & commissioning of RJ 45 connectors, interfaces, Mounting hardware, Patch Cords, Fiber Patch Cord, HDMI/VGA cable ( min 15 meters) with connectors at both side, Jacks, Plugs, tags, identifiers, fixtures, clamps, screws, nut - bolts etc. as required for the installation and commissioning of the complete job.

Supply & Erection of 75mm dia GI poles suitable for mounting camera for 3.0 mtr. Mounting height. Provision to be made for cable entry and connection for camera with all fixing arrangement to the pole etc, complete as required.

Supply & Erection of 75mm dia GI poles suitable for mounting camera for 6.0 mtr. Mounting height. Provision to be made for cable entry and connection for camera with all fixing arrangement to the pole etc, complete as required.

Supply & installation of fabricated GI plate & all required accessories to be mounted on existing electrical pole/wall for cameras.

Supply and fixing of 14 SWG CRCA sheet steel powder coated raceways of size 200 mm wide x 50 mm deep (2 mm) with junction boxes (junction boxes as required at at site condition to make the system efficient) and 2 mm / 3 mm thick top cover for electrical & LV wiring including neoprene gasket in joints, fixing the raceway on ceiling/ wall/ column surface with all necessary hardwares as required and including necessary civil work such as chase cutting/existing floor cutting including RCC/ PCC as per site conditions.

Supply and fixing of 14 SWG CRCA sheet steel powder coated raceways of size 300 mm wide x 50 mm deep (3 mm) with junction boxes (junction boxes as required at at site condition to make the system efficient) and 2 mm / 3 mm thick top cover for electrical & LV wiring including neoprene gasket in joints, fixing the raceway on ceiling/ wall/ column surface with all necessary hardwares as required and including necessary civil work such as chase cutting/existing floor cutting including RCC/ PCC as per site conditions.

Supply, laying, termination, testing and commissioning of single mode armored- uni tube 6 core fiber optic cable complete as required.

Supply, laying, termination, testing and commissioning of 2 core 1.5 Sq.mm.copper power armored cable on existing cable tray including the cost of making of connections, complete as required.:-

Supply, laying, termination, testing and commissioning of 1100 V Grade PVC insulated FRLS Copper conductor wires of size 3 x 2.5 sq. mm. PVC insulated copper wire. in MS conduits including end terminations with lugs and terminal blocks, connections etc. complete as required.

Supply, laying, termination, testing and commissioning of 1100 V Grade PVC insulated FRLS Copper conductor wires of size 3 x 1.5 sq. mm. PVC insulated copper wire. in MS conduits including end terminations with lugs and terminal blocks, connections etc. complete as required.

Material For Steel Structure including supply, fabrication & fixing.

Supply & fixing of Fabricated PVC Duct(with cover) for concealing cable- 50 x 100 mm.

Providing and erecting Providing and erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 100 mm height comprising all required standard accessories.

Providing and erecting Providing and erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 200 mm width & 100 mm height comprising all required standard accessories.

Supplying, installing, testing and commissioning of Supplying, installing, testing and commissioning of main fire pump(MFP / EP) suitable for water discharge of 2280 to 2850 LPM at 120 to 90 m head driven by electric motor 415 volts 3 phase 50 Hz AC supply of 75kW or of suitable kW capacity for manual/automatic operation and consisting of following (a) Horizontal type single stage centrifugal/split casing pump of cast iron body & bronze impeller with stainless steel shaft(SS410 grade) mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor TEFC synchronous speed 3000 RPM suitable for operation with IP 55 protection for enclosure horizontal foot mounted type with Class-F insulation conforming to IS-325. (c) M.S. fabricated common base plate coupling coupling guard foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-MFP/SSC/EP1

Supplying, installing, testing and commissioning of Supplying, installing, testing and commissioning of jockey fire pump (JP) suitable for water discharge of 180 to 240 LPM at 140 to 110 m head driven by electric motor 415 volts 3 phase 50 Hz AC supply of 15 kW or of suitable kW capacity for manual/automatic operation and consisting of following (a) Horizontal/vertical type multi stage centrifugal casing pump of cast iron body & bronze impeller with stainless steel shaft(SS410 grade) mechanical seal conforming to IS 1520. (b) Suitable kW Squirrel cage induction motor TEFC synchronous speed 3000 RPM suitable for operation on 415 volts 3 phase 50 Hz AC supply with IP 55 protection for enclosure horizontal foot mounted type with Class-F insulation conforming to IS-325. (c) M.S. fabricated common base plate coupling coupling guard foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003)complete as per specification no. FF-MFP/JP

Supplying, installing, testing and commissioning of Supplying, installing, testing and commissioning of main fire pump (MFP/DP) suitable for water discharge of 2280 to 2850 LPM at 120 to 90 m head driven by 110 HP or suitable HP capacity diesel engine at required working speed suitable for automatic operation and consisting of following (a) Horizontal type single stage centrifugal casing pump of cast iron body & bronze impeller with stainless steel shaft(SS410 grade) mechanical seal conforming to IS 1520. (b) Water cooled with radiator diesel engine conforming to relevant IS standard complete with auto starting mechanism 12/24 volts DC electric starting equipment with battery of required AH capacity with necessary charger suitable to work on 230v 50Hz AC supply diesel tank of minimum 150ltr capacity with first filling of diesel up to 100% level with necessary piping with valves up to engine exhaust pipe extended up to 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding residential silencer instruments and protection as per standard specification stop solenoid for auto stop in the event of fault with audio indications etc. as required. (c) M.S. fabricated common base plate coupling coupling guard foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning proper levelling complete pump set with engine assembly and accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-MFP/SSC/DP

Supplying and erecting Supplying and erecting G.I. pipe ‘C’ class ERW 25 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting Supplying and erecting G.I. pipe ‘C’ class ERW 50 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting Supplying and erecting G.I. pipe ‘C’ class ERW 65 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting Supplying and erecting G.I. pipe ‘C’ class ERW 150 mm dia with necessary fittings complete as per specification no. FF-PP

Providing Providing G.I. pipe ‘C’ class ERW 200 mm dia with necessary fittings complete as per specification no. FF-PP

Providing Providing coating of bitumen paint & 4mm thick wrapping for underground 100 mm ring main of fire fighting system.

Providing Providing coating of bitumen paint & 4mm thick wrapping for underground 150 mm ring main of fire fighting system.

Supplying and erecting Supplying and erecting 200 mm dia Cast Iron end line strainer of Y-type flanged end pattern PN16 pressure rating screen of SS end connection with Flanged / Screwed / Socket Weld / Butt Weld End etc with standard OAR (open area Ratio) for positive suction complete as per specification no. FF-VL/ELS

Supplying and erecting Supplying and erecting 75/80 mm dia. cast iron double flange sluice valve complete with PN16 pressure rating as per specification no. FF-VL/SV

Supplying and erecting Supplying and erecting 100 mm dia. cast iron double flange sluice valve complete with PN16 pressure rating as per specification no. FF-VL/SV

Supplying and erecting Supplying and erecting 150 mm dia. cast iron double flange sluice valve complete with PN16 pressure rating as per specification no. FF-VL/SV

Supplying and erecting Supplying and erecting 200 mm dia. cast iron double flange sluice valve complete with PN16 pressure rating as per specification no. FF-VL/SV

Supplying and erecting Supplying and erecting 75/80 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating as per specification no. FF-VL/BFV

Supplying and erecting Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating as per specification no. FF-VL/BFV

Supplying and erecting Supplying and erecting 150 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating as per specification no. FF-VL/BFV

Supplying and erecting Supplying and erecting 75/80 mm dia cast iron double flange NRV complete with PN16 pressure rating as per specification no. FF-VL/NRV

Supplying and erecting Supplying and erecting 100 mm dia cast iron double flange NRV complete with PN16 pressure rating as per specification no. FF-VL/NRV

Supplying and erecting Supplying and erecting 150 mm dia cast iron double flange NRV complete with PN16 pressure rating as per specification no. FF-VL/NRV

Supplying and erecting Supplying and erecting 200 mm dia cast iron double flange NRV complete with PN16 pressure rating as per specification no. FF-VL/NRV

Supplying and erecting Supplying and erecting 25 mm dia gun metal gate valve complete with PN16 pressure rating as per specification no. FF-VL/GV

Supplying and erecting Supplying and erecting 50 mm dia gun metal gate valve complete with PN16 pressure rating as per specification no. FF-VL/GV

Supplying and erecting Supplying and erecting stainless steel single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV

Supplying and installing Supplying and installing wall mounting swinging hose reel drum fitted with 19 mm dia. 30m long high pressure polypropylene (Polyhose) along with necessary accessories complete as per specification no. FF-FFA/HV

Supplying and erecting Supplying and erecting 63mm dia reinforced rubber lined (R.R.L.) hose pipe 15m in length fitted with necessary accessories complete as per specification no. FF-FFA/RRL

Supplying and erecting Supplying and erecting stainless steel branch pipe 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specifications no. FF-FFA/NZ

Supplying and erecting Supplying and erecting 150 mm dia fire brigade header suitable for supplying water in fire tank complete as per specification no. FF-FA/FBC

Supplying and erecting Supplying and erecting 20/25mm dia gun metal air release cock with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV

Supplying and erecting Supplying and erecting 100 mm dia. pressure gauge 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve erected with provided G.I. pipe elbow etc. complete as per specification no. FF-FFA/PG

Supplying and erecting Supplying and erecting 12/15 mm dia pressure switch with provided isolation valve G.I. nipple elbow etc complete as per specification no. FF-FFA/PS

Supplying and erecting Supplying and erecting M.S./CRCA cabinet for housing single hydrant valve of size ( 400 x 400 x 400)mm or hose pipe box of size ( 600 x 600 x 200)mm made from min. 1.5 mm thick CRCA sheet with angle iron work of min. of size (25 x 25 x 4) mm having front doors with viewing glass of size (200x150) mm and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5)

Supplying and erecting Supplying and erecting M.S./CRCA cabinet for housing Floor Hydrant valve hose pipe hose reel and branch pipe (size 1000 x 736 x 736 mm.) made from 16 SWG sheet and angle iron 25 x 25 x 4 mm. having front doors with viewing glass (8 x6 ) and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5)

Supplying and erecting Supplying and erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

PIPE AND VALVE Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 0.00 to 1.50 m.) By Manual Means

Providing and fixing flanged flexible connectors in SS 304 braiding, of rating PN 1.6 or equivalent, to provide stress relief for suction/delivery of pumps, complete with standard flanges, nuts, bolts etc. 150mm dia (min. 150 mm length)

Providing and fixing flanged flexible connectors in SS 304 braiding, of rating PN 1.6 or equivalent, to provide stress relief for suction/delivery of pumps, complete with standard flanges, nuts, bolts etc. 100mm dia (min. 150 mm length)

Providing and fixing flanged flexible connectors in SS 304 braiding, of rating PN 1.6 or equivalent, to provide stress relief for suction/delivery of pumps, complete with standard flanges, nuts, bolts etc. 80mm dia (min. 150 mm length)

Providing and fixing flanged flexible connectors in SS 304 braiding, of rating PN 1.6 or equivalent, to provide stress relief for suction/delivery of pumps, complete with standard flanges, nuts, bolts etc. 65mm dia (min. 150 mm length)

Providing and fixing standard fire mans axe with heavy duty insulated rubber handle as per IS: 926 with clamps.

Pressure Vessel for Fire Pump Supply, Installation, Testing & Commissioning double flanged vertical air vessel fabricated from 10mm M.S. plate with dished ends from 8mm M.S. plate, outside with one coat of primer and two coats of synthetic enamel paint of approved shade, complete with approved quality and sufficient number of pressure switches, air release valve, tripod type stand, pressure gauge with ball valve, drain ball valve of 50mm dia with 2.0 meter long GI (Heavy Duty ) piping complete as required and all other required accessories to operate commonly main fire pump, diesel fire pump and Jockey pump at drop of pressure, automatically at required pressure setting (Pressure switch assembly to be fabricated at site); Recommended dia. : 250 mm, Height of shell : 1200 mm, Working pressure : 18 Kg/cm2, Test Pressure : 16 Kg/cm2

Supplying and erecting ABC powder type fire extinguisher as per IS 13849 /15683 of 6 kg capacity with necessary clamp for erection on wall.

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 35 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE insulated unarmoured cable 1100 V. 1 core 35 sq. mm. copper conductor complete erected with provided lugs, laid in provided control panel /distribution boards / pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating XLPE insulated unarmoured cable 1100 V. 1 core 70 sq. mm. copper conductor complete erected with provided lugs, laid in provided control panel/distribution boards / pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 2 core 4 sq mm copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU for Speaker Cable (Make: Havells/ KEI/ Polycap/ RR)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 2.5 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 90 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/ road surface, to required depth complete. (Make: Crown/ Apsara/ RR Industries/ Equivalent)

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware.

Supplying, installation and testing of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly back fill ground enhancing compound required to fill up the excavated earth with required quantity complete, and recording the results Specification no. EA-MOBI

Providing & fixing earthing with copper earth plate size 60 x 60 x 0.315 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover with minimum 25 kg Carbon based environment friendly back fill Ground Enhancing compound complete with all materials, testing & recording the results as per specification no ESE -LA

Supplying and erecting copper strip of high purity required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint with joints required. As per specification no. EA-EP.

Audio systems Supply installation and fixing Equipment Rack - 19 " standard 36 U Rack with all required accessories. Earthing community kit, mounting bracket, cable manager, support angle, equipment shelf, mounting hardware, fan housing units etc, Ventilated top and bottom covers with attractive styling. It has Removable side panels with slam latches for easy access. (Make: Natmas/ APW/ Netrack)

Supply, installation, testing and commissioning of a 3-way, Dual 11.25" D'Apolito Loaded High Energy Horn Loaded Speaker System. The speaker shall meet the following performance criteria: Serviceable frequency range of 63 HZ - 20 kHZ (-10 dB) or better and a frequency response of 57 HZ - 20 kHZ (-3dB) or better.For HF mode, the rated power which the speaker should be able to utilize for long periods of time shall be atleast 100 W while rated power which the speaker should be able to handle in short bursts shall be atleast 400 W. In MF Mode, rated power which the speaker should be able to utilize for long periods of time shall be atleast 250 W while rated power which the speaker should be able to handle in short bursts shall be atleast 1000 W. In LF Mode, rated power which the speaker should be able to utilize for long periods of time shall be atleast 550 W while rated power which the speaker should be able to handle in short bursts shall be atleast 2200 W. In Standard mode, horizontal dispersion pattern of 70º or better while vertical dispersion of the array shall be 40º or better. In Wide Mode, horizontal dispersion pattern of 90º or better while vertical dispersion of the array shall be 50º or better. In Standard mode, the maximum decibel (dB) level which the speaker should be able to deliver without distortion be atleast 143 dB. In Wide Mode, the maximum decibel (dB) level which the speaker should be able to deliver without distortion be atleast 142 dB. In HF mode, Sensitivity should be 114 dB or a cut above.In MF mode, Sensitivity should be 107 dB or a cut above. In MF mode, Sensitivity should be 106 dB or a cut above. In HF/MF/LF mode, the nominal impedance should be 8 ohms.The crossover frequency of the speaker should be 200Hz, 2 kHz (Active). For LF, there shall be 2 x 11.25” ferite transducers -3.5” vc or better. For MF, there shall be 1X3" Ferrite Transducers - 3" VC or better. The aesthetics should comprise of a Marine Birchwood Cabinet(premium grade) enclosure, Perforated Stainless Steel Grill backed by acoustically transparent foam over a stainless steel mesh with Slide Bolt Locking System with Fly Adapters for Underhangs mounting system or better. (Make: D&B Audiotechnik/ Lacoustic/British acoustics)

Supply, installation, testing and commissioning of a 21” Horn Loaded Sub for an Extended LF Response. The speaker shall meet the following performance criteria: Serviceable frequency range of 19 HZ - 200 HZ (-10 dB) or better and a frequency response of 22 HZ - 140 HZ (-3dB) or better. The rated power which the speaker should be able to utilize for long periods of time shall be atleast 2000 W while rated power which the speaker should be able to handle in short bursts shall be atleast 8000 W. The coverage pattern should be omni-directional. The maximum decibel (dB) level which the speaker should be able to deliver without distortion be atleast 137 dB. Sensitivity should be 98 dB or a cut above. The nominal impedance should be 4 ohms. For LF, there shall be 21" Long Excursion ADR Drivers, 5.3" VC - Neo or better. The aesthetics should comprise of a Marine Birchwood Cabinet(premium grade) enclosure, Perforated Stainless Steel Grill backed by acoustically transparent foam over a stainless steel mesh with Integrated Handles - M-10 insertion points mounting system or better. (Make: D&B Audiotechnik/ Lacoustic/British acoustics)

Supply, Installation, Testing & Commissioning of Software Controlled Digital DSP with below Specifications:- Number of Inputs - 4, Number of Outputs - 8, Input Impedance - 12kΩ unbalanced, 24 kΩ balanced, CMMR - >45 dB, Adjustable Delay - 1 second / input & 1 second / output, Approved Makes: OHM, British Acoustics, D&B, Martin Audio, L-Acoustics, Renkus Heinz, Powersoft, Lab Gruppen (Make: D&B Audiotechnik/ Lacoustic/British acoustics)

Projection System Supply, Installation, Testing and Commissioning of Projector 3-chip DLP, should have 3 laser diaodes for true color production(Red,green,blue), Min output resolution 3840 x 2160 (UHD 4K), brightness min. 25,000-30,000 lumens, RGB Laser digital projector , Contrast Ratio : min 6000 : 1, illumintion minimum 50000 hours, Omni directional,Motorized horizontal and vertical lens offset , Inputs: 12G SDI,HDMI 2.0,DP,Analog Controls: RS232 in/out, RS422 in, Ethernet (10/100), Weight should not be more than 42kgs, Noise should not be more than 50dB, REC 2020 color space production, image processing minimmum 1.2Gpx/s, typical power consumption should not bemore than 1550 watts, should be complete with mounts and lens (Make: Sony/ NEC / Christie)

Supply, installation, testing and commissioning of Projection housing enclousure Interface for setup and monitoring of temperature, humidity and status indicators. Power control circuit with PID Management system compitable with the projection housing unit and display unit. Assembly and mounting of projector as per site plan with cables, mounting brackets and tilt/pan arrangement systems for projection layout. (Make: DMI/ ASL/ VIZBOX / Equivalent)

Supply, installation, testing and commissioning of RDM Control panel with Independant Digital Led Display for Monitoring of Temperature and Humidty , exaust control circuit, heating circuit, and power distribution for the projectors. (Make: DMI/ ASL/ VIZBOX / Equivalent)

CONTROL ROOM Supply, installation, testing and commissioning of Master Server with Intel i7/i9 Processor Windows 10/11 (With lifetime license) with 32GB RAM or more, GPU with keyboard mouse. (Make: Dell/ HP/ Asus/ or Equivalent)

Supply, installation, testing and commissioning of Media Server - Intel Core i7/i9 Series Processor or above with following minimum specifications: 32 GB RAM system memory, Minimum 1TB SSD storage, Dedicated 8 GB Graphic card (NVIDIA/AMD), CD Rom, DVD ROM, USB 3.0 interface with 4 USB ports, Wireless key board, Wireless mouse with licensed loaded Window 8/10, LAN, Audio Jack, VGA port, Line in - Line out and Video Output DVI,HDMI etc. (Make: Dell/ HP/ Asus/ or Equivalent)

Supply, installation, testing and commissioning of Lighting Control software complete with necessary software and hardware interface, license as required, DMX recording available, DMX 512 protocol enabled, Show timeline management (Make: MA Lighting/Avolite/ Equivalent)

Supply, installation, testing and commissioning of Media Production Software for Multi media show .Lisence & other fees are inclusive in this rates and shall be borne by bidder. (Make: Dataton/ Vioso/ AV Stumpfl)

Supply, installation, testing and commissioning of ARTNET Box with 3 or 5 pin XLR points for programming of lights (Make: Enttec/ Equivalent)

Supply, installation, testing and commissioning of DMX Splitter- The DMX-512 splitter shall have minimum one DMX input and six DMX output connections, the sockets being standard 5-pin AXR connectors. The opto isolated DMX-512 splitter shall have a power on LED and DMX active LED indication on the front panel. The opto isolated DMX-512 splitter input shall be internally terminated. (Make: Lite Putter/ Avolite/ LBT/ Sholite)

Supply, installation, testing and commissioning of 24 inches Flat LCD Display Monitors with Optimal Resolution of 1920 x 1080 at 60 Hz having Brightness 250 cd/m² (typical). CONNECTIVITY 1 Digital Visual Interface connectors (DVI-D) with HDCP 1 Video Graphics Array (VGA) 1 USB 2.0 upstream port 2 USB 2.0 downstream ports DC power connector for Soundbar (Make: Dell/ HP/ Asus/ or Equivalent)

Supply, installation, testing and commissioning of 40 KVA, true on-line UPS 3 Ph double Conversion with all safeties and protection and suitable capacity sealed maintenance free 12 V batteries, with a 30 mins backup time on full load with MS open MS Battery rack and Nyvin cable. (Make: Eaton/ BPE/ Emerson / Equivalent)

Supply, installation, testing and commissioning of Small Business 24 port Gigabit switch and 2 x Mini GBIC fiber uplinks. Standards:-IEEE 802.3, 802.3u, 802.3x, 802.3ab. Cabling Type:-Category 5 and multi-mode fiber. Power:-100-127VAC/200-240VAC, 1.0A/0.5A, 50-60 Hz. Operating Temperature:-32 to 104ºF (0 to 40ºC). (Make: Cisco/ Dlink/ Netgear)

Supply, installation, testing and commissioning of Video Transmitter and Receiver Set Max Data Rate 10.2 Gbps, Resolution Range Up to 2560x1600* @ 60 Hz or 4K (4096x2160) @ 30 Hz, UHD (3840x2160) @ 30 Hz, Low power consumption, compliances CE, c-UL UL, CE**, C-tick, FCC Class A**, ICES (Make: Kramer/ Extron/ HoC/ Linetek)

Supply, installation, testing and commissioning of HDMI to HDMI cable supports signals up to 4K x 2K Video and more color spare, 15.2 Gbps DTR, 10MΩ minimum Insulation resistance, -25 to 80 degree Celsius Working Temperatre (Make: Kramer/ Extron/ HoC/ Stricker/Equivalent)

LASERS & LIGHT Supply, installation, testing and commissioning of Laser 10000 mW power Graphics capable - 45kpps @ 8° ILDA Full colour mixing - analog modulation Link multiple units with linking Power, DMX and ILDA, Create custom content, store it inside the laser and play it back in different modes including programming and playback software. (Make: Laserworld/ Kvant/ LPS/ Equivalent)

Supply, installation, testing and commissioning of Laser housing enclouser with assembly and mounting of projector as per site plan with cables, mounting brackets and tilt/pan arrangement systems for projection layout. (Make: DMI/ ASL/ VIZBOX)

Supply, installation, testing and commissioning of Weather Proof IP66 Moving head light minimum 410W, lifespan of minimum 2000 hrs, Pan min 150 degrees, Tilt minimum 270 degrees, 1 colour wheel with 13 colours + white bidirectional, DMX controlled, Variable strobe from 1 - 25Hz, Dimming 0-100% linear. (Make: Chauvet, Sholite, Martin)

Supply, installation, testing and commissioning of Software solution to control the laser with all controls and effects, Ethernet or DMX accessibility, Timeline show management, Sychroniseable with Master control software. (Make: Laserworld/ Kvant/ LPS/ LBT)

Supply, installation, testing and commissioning of Water Fountains Nozzles Multi-Directional Drive Nozzle 2D in SS304 with minimum rotation range above water surface up to 160deg, minimum net weight 15kg, stepper torque of two phases (Effect Height 3-7 Mtr) (Make: ASL/ DMI/ PEM / Equivalent)

Supply, installation, testing and commissioning of Ultra Fast Action jet (SS304/Brass) with simple and safe clamping system, low splash, low noise level (Effect Height 3-7 Mtr) (Make: ASL/ DMI/ PEM / Equivalent)

Supply, installation, testing and commissioning of Sunburst Jet - SS 304/Brass with simple and safe clamping system, low splash, low noise level (Effect Height 3-7 Mtr) (Make: ASL/ DMI/ PEM / Equivalent)

Supply, installation, testing and commissioning of Rainbow Jet - SS304/Brass with simple and safe clamping system, low splash, low noise level (Effect Height 3-7 Mtr) (Make: ASL/ DMI/ PEM / Equivalent)

Supply, installation, testing and commissioning of Shooter Jet-SS304/Brass with simple and safe clamping system, low splash, low noise level (Effect Height 7-12 Mtr) (Make: ASL/ DMI/ PEM / Equivalent)

Supply, installation, testing and commissioning of High Jet -SS304/Brass with simple and safe clamping system, low splash, low noise level (Effect Height 12-15 Mtr) (Make: ASL/ DMI/ PEM / Equivalent)

Supply, installation, testing and commissioning of Rotating Jet Set of four Nozzles with simple and safe clamping system, low splash, low noise level (Effect Height 2-4 Mtr) - SS304/Brass (Make: ASL/ DMI/ PEM / Equivalent)

Supply, installation, testing and commissioning of One Spray ring Dome shape (Inward Ring) & One spray ring (outward) (SS Ring with upto 24nos to 42nos. Nozzles -SS304/Brass ) (Effect Height 3-4 Mtr) (Make: ASL/ DMI/ PEM / Equivalent)

Supply, installation, testing and commissioning of Diamond Jet (Effect Height 2-3 Mtr) with simple and safe clamping system, low splash, low noise level (Make: ASL/ DMI/ PEM / Equivalent)

Supply, installation, testing and commissioning of SS 304 Header accessory for above Ultra Fast Action Jet nozzles (Make: Customised)

Supply, installation, testing and commissioning of SS 304 Header accessory for above Sunbrust jet (Make: Customised)

Supply, installation, testing and commissioning of SS 304 Frame set Custom made SS 304 Frame set for all fountains (Make: Customised)

Supply, installation, testing and commissioning of Platform for Laser Projector & Video Projector (Custom made SS 304 Frame set with uPVC/Fiber Reinforced Plastic for Laser Projector & Video Projector) (Make: Customised)

Supply, installation, testing and commissioning of Fountain Lights IP68 Submersible LED Color Changing Light 36W, IP68 ideal for fountains and ponds, fully sealed design, Voltage 220V, colour temperature: 2700-2000K, 3500-4100K, 5000-6500K(Make: ASL/ DMI/ PEM / Equivalent)

Supply, installation, testing and commissioning of Submersible LED Color Changing Light 54W, IP68 ideal for fountains and ponds, fully sealed design, Voltage 220V, colour temperature: 2700-2000K, 3500-4100K, 5000-6500K (Make: ASL/ DMI/ PEM / Equivalent)

Supply & installation of Light Stands made of SS 304 as per site requirements (Make: ASL/ DMI/ PEM / Equivalent)

Supply & installation of Connection Box for Solonoid Valves & Lights (Make: ASL/ DMI/ PEM / Equivalent)

Supply, installation, testing and commissioning of Submersible Pumps of totalling capacity 25HP with Suction Strainer for pumps, Three phase, Voltage 415V, corrosion resistant, high discharge capacity and advanced water cooled motor design ensuring optimum efficiency and low energy consumption (Make: KSB/ C.G/ Kirloskar/ Grundfos)

Supply, installation, testing and commissioning of Submersible Pumps of totalling capacity 5HP with Suction Strainer for pumps, Three phase, Voltage 415V, corrosion resistant, high discharge capacity and advanced water cooled motor design ensuring optimum efficiency and low energy consumption (Make: KSB/ C.G/ Kirloskar/ Grundfos)

Supply, installation, testing and commissioning of Submersible Pumps of totalling capacity 1.5HP with Suction Strainer for pumps, Three phase, Voltage 415V, corrosion resistant, high discharge capacity and advanced water cooled motor design ensuring optimum efficiency and low energy consumption (Make: KSB/ C.G/ Kirloskar/ Grundfos)

Supply, installation, testing and commissioning of Show Controller with synchronised controls for fountains and VFDs, DMX protocol enabled, modular multimedia design to enable planning and designing for final realization (Make: Syncronorm/ PLC based/ Equivalent)

Supply, installation, testing and commissioning of Master fountain control server with Intel i7/i9 Processor Windows 10/11 (With lifetime license) with 32GB RAM or more, GPU with keyboard mouse. (Make: Dell/ HP/ Asus/ or Equivalent)

Supply, installation, testing and commissioning of On Site Fountain Programming, 4 person team, 30 days on-site programming including travel lodging baording

Supply, installation, testing and commissioning of Control Panels as per specifications:- Main Distribution Panel (Panel body custom made indoor type Made of 16 guage CRC/MS sheet epoxy powder coated with MCCB's & main bus bar for supply to the below no of panels. (Make: ASL/ NSE/ DMI / Equivalent)

Supply, installation, testing and commissioning of Control Panel for Hydro-shield Semicircular pumps Starter with DMX 512 controlled (Panel body custom made indoor type Made of 16 guage CRC/MS sheet epoxy powder coated with Amp meter, voltmeter, MCB, push button, isolator, indicator etc. panel incommer with MCB, neutral link etc and starter for pumps with Contactors, Overload Relays, Single Phase Preventers, internal wiring (Panel should be complete in all respect for automatic operation of pumps) Panel Equipments Make-L & T, Heger, Elmex,Rishabh,FTC, Esbee, Salzer,Schneider,Dowels, Jainsons, KSS,SG,Siemens etc.) (Make: ASL/ NSE/ DMI / Equivalent)

Supply, installation, testing and commissioning of Control Panel for pumps Starter/VFD's (Panel body custom made indoor type Made of 16 guage CRC/MS sheet epoxy powder coated with Amp meter, voltmeter, MCB, push button, isolator, indicator etc. panel incommer with MCB, neutral link etc and starter for pumps with Contactors, Overload Relays, Single Phase Preventers, internal wiring (Panel should be complete in all respect for automatic operation of pumps) Panel Equipments Make-L & T, Heger, Elmex,Rishabh,FTC, Esbee, Salzer,Schneider,Dowels, Jainsons, KSS,SG,Siemens etc.) (Make: ASL/ NSE/ DMI / Equivalent)

Supply, installation, testing and commissioning of Digital control panel for lights with DMX receiver and relay cards. (Panel body custom made indoor type Made of 16 guage CRC/MS sheet epoxy powder coated with power supplies, DMX transmitter and receiver cards, MCB's etc (Panel should be complete in all respect for automatic operation of lights) (Make: ASL/ NSE/ DMI / Equivalent)

Supply, installation, testing and commissioning of Digital control panel for Pump and solenoid valves with DMX receiver and relay cards. (Panel body custom made indoor type Made of 16 guage CRC/MS sheet epoxy powder coated with DXM cards, Electronic relays, Power Supplies & MCB's etc (Panel should be complete in all respect for automatic switching of solenoid valves and pumps) (Make: ASL/ NSE/ DMI / Equivalent)

Supply, installation, testing and commissioning of Digital control panel for 1D & 2D (Panel body custom made indoor type Made of 16 guage CRC/MS sheet epoxy powder coated with Stepper Drives DMX Relay cards and DMX Stepper Driver cards,Power Supplies etc (Panel should be complete in all respect for automatic operation of 1D & 2D Nozzles (Make: ASL/ NSE/ DMI / Equivalent)

Supply, installation, testing and commissioning of Valves, fittings etc Suitable size Solenoid Valve for Ultra Fast Action jet-SS 304, IP68 with control coil (Make: Uflow/ Rainbird/ Hunter/ Rotex / Equivalent)

Supply & installation of 4-SEATER PADDLE BOAT OF FIBER GLASAS SHIP SHAPE,CAPACITY : 4 Person

Supply, installation, testing and commissioning of Electrical Panel, Cabling & Earthing DMX Cable 18 AWG 18/0.20 mm x 2 Core ATC copper conductor PE insulated, core twisted in a circular form inner sheathed with moisture proof polymer, beard shieleded (80% with ATC Copper, outter jacket with matt finished PVC. (Make: Beldon/ Krystal/ Polycap/ Kramer)

Supply, installation, testing and commissioning of CAT 6/5e Shielded Twisted Pair cable for signal & data transmission. 24 AWG twisted pair conductors inside an overall braid and foil shield. Shielded Twisted Pair cable should provides added protection from outside interference and ensures high quality signal transmission (Make: Beldon/ Dlink/ Extron/ Kramer)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 1.5 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supply, installation, testing and commissioning of Electrical panel (LT Panel)- Distribution equipment like electrical distribution board, field junction boxes and luminaries' / speaker junction boxes etc. -shall be designed as per the final project concept approved for the show for the control as well as the distribution of power/controls to various equipments in the field/ controlroom. (Make: Customised)

Supply & Fixing of Weatherproof (IP-65) Thermoplastic Cable Junction Box with terminal block fitted inside the box suitable for all the cables (both end) (Make: Dowell/ Diamond/ Equivalent)

Supply, installation, testing and commissioning of Connectors and acessories

Designing, Supply, Fixing and installation of Poles for Speakers, MS poles painted and foundation with calculated structural stability

Designing, Supply, Fixing and installation of Poles for Laser and Projector Stands, MS poles painted and foundation with calculated structural stability

Content Creation Script writing: includes movement, actions, expression and dialogue of the characters, drama etc for about 35-40 mins.

Audio Visual Content Part-1: includes visual Storyboard, Storytelling, 2D 3D animation, Graphics, Art Works, Archival Imagery, Video-timeline, SFx, VFx, Voiceovers and Music etc for the show.

Audio Visual Content Part-2: includes visual Storyboard, Storytelling, 2D 3D animation, Graphics, Art Works, Archival Imagery, Video-timeline, SFx, VFx, Voiceovers and Music etc for the show.

Music composition and direction Part-1: conceptualization and designing of music track for VO, musician to play instruments. background sound. archival sound mixing and design. songs, etc.

Music composition and direction Part-2: conceptualization and designing of music track for VO, musician to play instruments. background sound. archival sound mixing and design. songs, etc.

Art Work: includes design and development of pictures, digital illustration, sketch, characters, etc for the show. The Artwork should be created by professional Artist and Illustrator.

Voiceovers Part-1: The narrator voiceover will be as per proposed artist. The show narration will be in Hindi & English language. All other character voiceover will be done by professional artists only.

Voiceovers Part-2: The narrator voiceover will be as per proposed artist. The show narration will be in Hindi & English language. All other character voiceover will be done by professional artists only.

Laser Animation and Programming: Creating laser beam show and designing of laser animation and effects according to script, characters, events, mood, drama etc and creating timeline sync with the audio video storyline.

On Site Audio Design and Distribution: Distribution of layers of music track and VO as per Audio distribution system.

Edge Blending and Projector Mapping: Alignment of multiple projectors for edge blending using cutting edge technology and as per show requirement.

M/s Kranti Construction (BID ID -6466829)

N.M.Sonawane (BID ID -6464082)