SPECIAL REPAIR TO THE JOINERY, ROOF AND CERTAIN EXTERNAL PORTION OF THE OFFRS MD ACCN IN BAIRAGARH UNDER GE BHOPAL

M&L using ready mix plaster for rendering 15 mm thick on fair faces of brick/concrete surfaces cement plaster in CM (1:4) , finished even and smooth without using extra cement, incl Taking down cement plaster on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water or cement lime plaster any description complete all as specified and directed. (material and Purchase vr shall be produced before execution)

M&L using ready mix plaster for 10mm thick rendereing brick or concrete surface in CM 1:6 finishing the surface fair & even without using extra cement incl Taking down cement plaster on brick or stone wall etc including raking out joints, hacking for key, scrubbing down with water or cement lime plaster any description. complete all as specified and directed. (Material and Purchase vr shall be produced before execution)

M&L for applying one coat of white waterproof wall putty 1mm thick on walls complete all as specified and directed.

M&L for preparation of prepared plastered or unplastered surfaces of walls and applying two coats of oil bound distemper complete all as specified and as directed.

M & L for dampness rectification on Wall Area :- Surface Preparation: Removing existing putty/plaster/POP surface from the affected wall with wire brush/grinder/hammer etc up to brick level, filling of crack fill paste in visible cracks and apply two coats of DAMP STOP RAINCOAT BY DR FIXIT (one coat diluted and other coat undioluted) over finished surface. Necessary scaffolding suitable for height upto 10.00 mtr from average ground level complete all as specified and as directed. (100% Material to be produced before execution of work)

Dismantling of timber scantling in fillets, rails, posts, rafters, purlins etc 40 sqcm and over in section, in any posotion for unframed works complete all as specified and directed.

S&F steel work in tubular/angle trusses including special shaped washers, purlins, rafters, posts etc complete all as specified and directed.

M&L Pre Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick AZ-150 of an colour having tensil strength of 550/MPA as in roof covering/cladding to wall/ ridge,fixed with self tapping screw/L type or J type cranked hook bolts incl Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete all as specified and directed.

M&L Pre Galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick AZ-150 of an colour having tensil strength of 550/MPA as in roof covering/cladding to wall/ ridge,fixed with self tapping screw/L type or J type cranked hook bolts incl Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof covering complete all as specified and directed.

M&L for Dholpur stone with hammer dressed facework (with maximum depression from a straight edge held against the dressed surface not exc 20mm), about 40mm high, 75mm deep in straight courses, laid and jointed in cement and stone dust mortar 1:3, recess pointed (10mm x 20mm) with an admixture of white cement and Dholpur stone dust 1:1 complete all as specified and directed.

M&L Granite 16-18 mm thick (of any type) work (machine cut) in steps, jambs, pillar, window-cills, cooking platform and like in 15 mm thick cement mortar (1:4) including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granite over 15 mm thick screed bed in cm 1:4 incl Dismantling of stone slabs and tiles of any description or thickness in floors, aprons, walls, etc, laid bedded and pointed in any mortar complete all as specified and directed.

M&L for rounding to edges of stone one edge such as in steps,cooking platform and other similar situation complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7mm to 8mm thick (square /rectangular ) area of each tile exceeding 0.11 sqm , but not exceeing 0.18 sqm , in floors over and including 15mm thick screed in CM 1:6 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles incl Dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing), removing serviceable tiles and rubbish off the permises compelte all as specified & directed

M&L for non skid ceramic coloured tiles 7mm to 8mm thick (square /rectangular ) area of each tile exceeding 0.11 sqm , but not exceeing 0.18 sqm , in Skirting over and including 10mm thick screed in CM 1:4 etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles incl Dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing), removing serviceable tiles and rubbish off the permises compelte all as specified & directed

M&L for glazed tiles , coloured 300x450 x 6 to 7 mm thick as in skirting/dado over & including 10mm thick rendering in CM 1:4 set & jointed in neat cement slurry & pointed in white or coloured cement incl Dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing), removing serviceable tiles and rubbish off the permises complete all as specified and directed.

M&L for water proofing treatment to sunken surfaces of slab including in following sequence complete :- (a) Slope correction providing PCC 1:1.5:3 using 12.5mm graded stone aggregate, average thickness 25mm , mixed graded styone aggregate , average thickness 25mm , mixed with integral water proffing compound "DITCHTMENT DM' manufactured by Dr fixit Pidiproof LW + of M/s Pidilite Industries or STP No 1 (Liquid) of M/S STP Ltd as approved by GE , in proportions as suggested by manufacturer. (b) Applying evenly a priming coat of bituminous primer confirming to IS 3384 @ 0.7 Kg per Sqm on prepared surfaces. (c) Applying evenly a coat of hot blown bitumen grade VG-10 @ 1.5kg/sqm on the primer surfaces. (d) Laying 150 micron thick black polythence film on the suface with 10mm overlaps sealed and bounded the surface. (e) Applying evenly a coat of hot bown of grade 85/25 @ 1.5 kg per sqm on the surfaces. (f) 48 hrs testing of treatment for water thightness by ponding of water. Rates incl demolition of existing suken slab and concrete complete all as specified and directed,

S&F 15mm GI tube medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors incl Taking up or down 15mm bore GI steel tubing and connections, including cleaning for refixing or removal to store and cutting chases, pinning in whereever reqd and make good in cm 1:3. complete all as specified and directed.

S&F 20 mm GI tube medium grade with all necessary fittings and fixed complete to wall and ceiling or laid in floors incl Taking up or down 20 mm bore GI steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed and cutting chases, pinning in whereever reqd and make good in cm 1:3 complete all as specified and directed.

S&F in repairs sinks with drainage board made of stainless steel 1mm thick kitchen or laborary with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantileer brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm complete all as specified and directed.

M & L for fabricating and fixing powder coated (Minimum 50 miciron ) aluminium sections of required size for doors, windows any type, frames and partitions including aluminium hinges of required size jointing cleats, screws salsh fasterners , plug for fixing with walls, column etc including taking down damage portion of damage door, windows or taking down complete door/ window complete all as specified and directed. Note :- Rates are inclusive of necessary new fitting for door/ window i.e handle, tower bolt, butt hinges etc complete

M&L framed work such as grills, gratings, gate etc with ends of bars souldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railing, frame work of water tanks and similar work conforming to Fe-290, Gde E-165 complete all as specified and directed.

S&F for Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to uPVC door with beading complete all as specified and directed.

S&F in repair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to uPVC door with beading complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc .50 sqm in each panels complete all as specified and directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc .50 sqm in each panels incliduing hacking out old broken glasses complete all as specified and directed.

S&F 3 mm thick figured glass, pin head type and glazing with oil putty in squares not exc 0.5 sqm in pane complete all as specified and directed.

Taking down chowkhats or frame with shutter n.exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed

S & F Solid PVC door frame of size 50 mmx 47mm made out of 5 mm plain colour PVC sheet reiforced with MS square tube and fixing in opening as per manufacturer instruction complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement complete all as shown in SSR-2004 Part - II, complete all as specified and directed.

Taking down door shutter any description exc 1.0 sqm but n.exc 2.00 sqm each complete all as specified and directed.

S&F for 40 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides and both face is covered with decorative face 0.9mm mica with lipping/frame to match complete all as specified and directed.

S&F 2nd class wood 30mm thick glazed and skelton shutter open rebeted and prepared to receive glass gauge etc(with sash bar) edges of framing plain champhered or rounded fitted with cut and mitred beads for securiing glass complete all as specified and directed.

Taking down chowkhats or frame with shutters exc 1.5 Sqm but not exc. 4.00 Sqm each (without taking off shutters from the frame) complete all as specified and directed

Factory made single extruded WPC (WoodPolymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65x105 mm comprisingof virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applyingPVC solvent cement and screwed with fullbody threaded star headed SS screwshavingminimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 modules ofelasticity 900 N/mm2 and resistance tospread of flame of Class A category withproperty of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/lugs/SS dash fasteners of required dia andlength complete as per direction of Engineer-in-Charge. →Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall beacceptable. Variation in profile dimensionson plus side shall be acceptable but no extrapayment on this account shall be made.

Factory made single extruded WPC (WoodPolymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65x125 mm comprisingof virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives(maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applyingPVC solvent cement and screwed with fullbody threaded star headed SS screwshavingminimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2 modules ofelasticity 900 N/mm2 and resistance tospread of flame of Class A category withproperty of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/lugs/SS dash fasteners of required dia andlength complete as per direction of Engineer-in-Charge. →Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall beacceptable. Variation in profile dimensionson plus side shall be acceptable but no extrapayment on this account shall be made.

Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mmsizecomprising of virgin polymer of K value 58-60(Suspension Grade), calcium carbonate and naturalfibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screwwithdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2and resistance to spread of flame of Class A category with property of being termite/borerproof, water/moisture proof and fire retardant and fixingwith stainless steel butt hinges of required size withnecessary full body threaded star headed counter sunkS.S screws, complete all as specified and directed.

Providing Factory Made 30mm thick 100% Solid WPC ( Wood polymer Composite ) Laminated Wiremesh Door Shutter of required size comprising of virgin PVC resin of K Value 57-60 ( Suspension Grade ), Calcium Carbonate and natural fibers ( Wood Powders/ rice husk/ wheat husk ) and Non toxic additives, made from Extrusion process WPC foam sheet Single Extruded ( Inner ) with having minimum density not less than 650 kg/cbm manufactured by "RAJSHRI" an ISO 9001 - 2015 Certified Company, having good screw holding capacity ( Screw Withdrawal strength of 2000 N ( Face ) & 1100 N ( Edge ), Minimum Compissive of 50 N/mm2 , Modulus of elasticity 850N/mm2 and resistance of spread of flame of Class A category with Property of being Termite/ Borer Free.Water/ Moisture Proof and Fire Retardant. WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter. For fixing Mosquito mesh and XTN aluminium mesh combinly panel area of door except stiles and rails to be panelled with mesh with self tapping round headed scresws at required distance, scres and edges covered with feathered pvc edge beading all around of mesh and fixing stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS Screws. complete all as specified and directed, Material test certificate and authentication should be compulsory provided by the manufacturing company :

S&F 150mm Aluminium anodised barrel tower bolts extruded section and fixed complete all as specified and directed.

S&F 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed

M&L for preparation new steel & iron surfaces of any description over 10cm in width or girth and applying two coat of synthetic enamel paint over and including a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for two coats of synthetic enamel paint over one coat of pink primer over 10cm width or girth on wooden surface incl prep. complete all as specified and directed.

Taking down eaves gutters and rainwater pipes( any size or pattern) , including all fittings, heads, shoes, bends , swan necks, etc, removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F PVC (SWR) pipe 75mm bore single socketed, in any length with rubber ring joints, fixed in walls / laid in trenches/floors complete all as specified and directed.

S&F PVC (SWR) 75mm bore bends any radious complete all as specified and directed.

S&F PVC (SWR) junction single, (SingleT) 75mm bore equal or unequal complete all as specified and directed.

S&F in repairs PVC (SWR) pipes 110mm dia single socketed, in any length with rubber ring joints laid in trenches , floors or fixed in walls complete all as specified and directed.

S&F PVC (SWR) 110mm bore bends any radious complete all as specified and directed.

S&F PVC (SWR) Junction (Single T) 110mm bore equal or unequal complete all as specified and directed.

M&L 75mm dia PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

M&L for brick work with sub class B bricks straight or curved on plan exc 6 m mean radius, built in cm 1:6 incl Demolition of brickwork or stone/boulder masonry , built in cement mortar including all quions, arches, pillars, etc but excluding ashlar facings dressed stonework and precast articles complete all as specified and directed.

S &F in repair Floor door stopper 150mm long of aluminium ally body and tonge , anodised , with hard drawn steel spring, fixed in floor complete all as specified and directed.

S & F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S & F Rotational moulded polyethylene water storage tanks 500 ltr cap (cylindrical vertical with closed top) hoisted and fixed in position incl 20mm dia PTMT float valve and dismantling of exisinting tank complete all as specified in SSR Part I complete all as specified and directed.

S & F Rotational moulded polyethylene water storage tanks 1000 ltr cap (cylindrical vertical with closed top) hoisted and fixed in position incl 20mm dia PTMT float valve and dismantling of exisinting tank complete all as specified in SSR Part I complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone agg) as in foundation , filling, subbase and mass incl Demolition of cement concrete in floors and pavings not exc. 15 Cm thickness (below/above ground level) including floor finishesconcrete complete all as specified and directed.

M&L for cement concrete 1:5:10 type E-2 (using 40 mm graded stone agg) as in sunken filling, mass concrete incl Demolition of cement concrete in floors and pavings not exc. 15 Cm thickness (below/above ground level) complete all as specified and directed.

M/L for 75 mm thick PCC 1:3:6 type C-1 , using 20 mm graded stone aggregate in plinth protection, aprons, hard standing, path and like including bitmuminous mastic filling in 1:3 joints(in every 3.00mtr) and finishing the surfaces even and smooth without using extra cement incl Demolition of cement concrete in floors and pavings not exc. 15 Cm thickness (below/above ground level) complete all as specified and directed

M&L for Heavy duty flooring tiles , harsh weather & UV resistance, high abrasion resistance, MOH hardness >6 thickness 15-18 mm thick , area of each tile not less than 0.09 sqm , anti slip type laid in floors , steps, edges etc set and jointed in neat cement slurry and pointed in white or coloured cement to match tile with & including 15 mm thick rendering in cm 1:4 and dismantling of exiting tiles complete all as specified and directed

M&L machine pressed precast concrete interlocking paver block (Reflective type)in any shape and size confirming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment including dismantling of existing stone slab tiles complete all as specified and directed.

M&L sand filling under paver block watering and consolidation complete all as specified and directed.

M&L for cement concrete type B1 1:2:4 (20 mm graded stone agg) as in coping, benching etc for drain and similar works incl of demolition of cement concrete complete all as specified and directed.

S & F in repair 20mm dia Ball valves highpressure of PTM with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified and directed. (Minimum weight 15mm-142gms/20mm-210gms./ 25mm-455gms/ 40mm- 690 gms)

M&L for 32 mm dia UPVC pipe as in water spout at the lowest point of sunken floor with 600 mm projection beyond the outer face of the wall with outer end cut in chamfered angle for easy drain of water complete all as specified and as directed.

S&F in repair 32mm bore PVC waste pipe for kitchen sink /WHB one mtr long complete all as specified and directed.

S&F in repair 100mm dia CP grating (Minium weight 25gms) complete all as specified and directed.

M&L for precast cement concrete type B1 (20 mm graded aggregates) as in cover slab for manholes etc set in CM 1:4 including demolition of existing cover slab complete all as specified and directed.

M&L for Double charge vitrified ceramic tile light shade 8-10 mm thick (square /rectangular) polished, area of each tile exceeding 0.36 Sqm as in floors/skirting over and including 15mm thick screed bed in CM 1:6 etc and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles incl Dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing), removing serviceable tiles and rubbish off the permises complete all as specified & directed.

M&L for vitrified ceramic tile light shade 8-10mm thick (Square /rectangular ) polixhed , area of each tile not exceeding 0.36 sqm on vertical surfaces such as skirting dado and risers to steps etc over & including 10mm thick rendering in CM 1:4 set & jointed in neat cement slurry & pointed in white or coloured cement to match incl Dismantling floor, hearth or wall tiling including cement mortar bedding(but not backing), removing serviceable tiles and rubbish off the permises complete all as specified & directed.

S & F Continuous (piano) hinges 30mm,mild steel, bright finish or electrogalvanised complete all as specified & directed.

M&L in repairs 18/19 mm thick ply boards for chowkhat, cupboard, grade 2 quality, interior grade, commercial type,decorative face with 0.9mm thick mica for lipping/frame to match on both faces fixed with screws to timber frame-work, fixed with screws/nails to timber frame work complete all as specified and directed.incl Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed. (Note : S.S butt hines and screws etc shall be including).

M&L in repairs 18/19 mm thick WPC panels for kitchen cabinet , fixed with screws to timber frame-work, fixed with screws/nails to timber frame work complete all as specified and directed. WPC to be fixed with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be including) complete all as specified and directed.

S&F 100 mm stainless steel butt hinges medium weight, cold rolled complete all as specified and directed

S&F 150 mm Aluminium handles, D type base plate, anodised complete all as specified and directed

S&F in repair kitchen basket fabricated with stainless steel section (SS-304), of best quality of size 430 mm x 508 mm x 200 mm for different use such as placing plain plate / dish / cup & saucer /cutlery / thali etc fixed in position on one pair telescopic channel of size 450 mm (when closed), mild steel chromium plated, roller type, heavy duty complete all as specified and directed.

S&F in repair kitchen basket fabricated with stainless steel section (SS-304), of best quality of size 430 mm x 508 mm x 100 mm for different use such as placing plain plate / dish / cup & saucer /cutlery / thali etc fixed in position on one pair telescopic channel of size 450 mm (when closed), mild steel chromium plated, roller type, heavy duty complete all as specified and directed.

S&F in repair telescopic channel of size 450 mm (when closed), for fixing kitchen basket in it, mild steel chromium plated, roller type, heavy duty fixed to wooden/ metal frame with SS screws complete all as specified and directed.

S&F in repairs for Hydraulic Soft close Auto hinges, Thickness 1-1.5 mm, size 8 Inch brass finish 90 Degree opening angle silver colour complete all as specified and directed.

S&F in repairs 12 mm thick Plywood, grade BWR, type BB, fixed with screws to timber frame work incl decorative laminate 0.9 mm type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instruction complete all as specified and directed.

Breaking the termite mounds, making holes with crow bars and pouring antitermite chemical emulsion at the rate of 4 litres per cubic metre of moundt complete all as specified and directed.

M&L for provn of water proofing roof treatment to non-accessible /accessible RCC roof with APP modified membrane with non-woven polyester reinforced wt not less than 3 Kg/Sqm of thickness not less than 3 mm having thermal; insulation with white or plain finish on upper side of membrane uniformly embedded during manufacturing process incl taking down existing treatment all as per following specifications:- (a) 10 mm thick plaster in CM 1:4 mixed with and including water proofing compound @3% by weight of cement applied over roof slab. After the plaster is cured the roof will be tested for water tightening by ponding with water for 72 Hrs for any seepage / leakages etc. if any seepage is observed the rectification will be carried out by pressure grouting under the pressure of 5 Kg/Sqcm using cement based cement grout. After the surface is repaired the slab will be tested for water tightness against before processing further treatments. (b) The surface of the roof, parapet and gutters, drain mouths etc. over which water proofing treatment is to be applied shall be cleaned of all foreign matters such as fungus, mass, dust etc. by wire brushing and dusting. For cast iron drain outlets the groove shall be cut around to tuck in the treatment as pipes, chimney stacs etc. and other similar situations to ease up about corners. (c) Hot blown bitumen VG-10 as in primer conforming to IS: 3384-1965 @ 0.30 Kg/Sqm to be applied on prepared surface till the surface is properly impregnated. (d) APP modified water proofing membrane as specified shall be laid by torch application method laid on hot bitumen 85/25 grade(bonding material) at the rate of 1.2 kg/sqm primer surface as per manufacturer’s instructions, The overlaps while torching shall be 100 mm in both directions(longitudinal and transverse directions). All overlap joints shall be sealed thoroughly by thermofusing both the membrane layers and sealing it with the help of hot trowel. The overlap joints shall be made as monolithic layer. (e) All joints & changes in direction should be curved with cement mortar 1:3 mixed with SBR latex @ 200 ml per beg of cement and cured well before laying the membrane. (f) A fillet of PCC (1:2:4) type B-0 of 100 mm x 100 mm shall be provided at all junctions of vertical and horizontal surfaces and wherever there is a change of direction. The membrane should not be taken over at any steep turns and hence all corners /junctions should be rounded.

S&F in repairs 15 mm pillar taps, fancy type , cast copper alloy, chromium plated, screwed down high pressure, with or without lettered "Hot or Cold" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair 15 mm Bib taps, chromium plated , screwed down, screwed for iron pipe or for brass ferrule and fixing complete all as specified and directed.

S&F in repairs 15 mm bore Bib taps, long body fancy type cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferulle and fixed complete all as specified and directed.

S&F in repairs 15 mm Stop/Angle valves, cast copper alloy, chromium plated screwed down high pressure, with crutch or butterfly handle, scrwed both ends for iron pipe or for unions and fixing complete all as specified and directed.

S&F in repairs 15mm bore stop cock, cast copper alloy chromium plated with long shank and cup (concealed type) screwed down , screwd for iron pipe or union and fixed in repair complete as specified and as directed.

S&F in repair 15mm dia brass CP wall mixer for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repair15mm dia brass CP centre hole basin mixer for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repair brass chromium plated shower rose 125mm in size with or without swivel joints any size incl fixing to steel pipe or union , complete all as spfecified & directed.

S&F in repair vitreous china squanting pan "Orissa" pattern size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) including cement concrete bedding complete all as specified and directred.

S&F Vitreous China Oval shaped cunter top Wash Basin, white , flat back, Size 550x400mm / std size including waste pipe , coupling, PVC pipe connection 15mm dia 600mm long complete all as specified .

S&F China wash down water closet pan (Pedestal Pattern), white , pedestal pan and 'P' or 'S' trap , plastic water closet seat , white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified.

S&F in repair Vitreous China Wash Basin, white , flat back, Size 630x450mm including brackets, waste pipe , coupling, PVC pipe connection 15mm dia 600mm long complete all as specified .

S&F in repairs PVC low level flushing cistern 10 ltrs capacity with all internal fittings incl 32mm dia flush pipe and fixing to supply pipe including PVC connection 600 mm long 15 mm bore with brass heads & washers with connections fixed in repairs complete all as specified.

S&F in repair health faucets CP with 1.2mtr long CP flexible pipe complete all as specified and as directed..

S&F in repairs Jet spray (butterfly) with 1 mtr tube complete all as specified and directed.

S&F in repair toilet paper holder of mild steel chromium plated 'D' type , fixed to walls with chromium plated brass screws complete all as specified and directed.

S & F in repair EWC seat cover white/coloured plastic with fixing bolts & hinging device complete ISI marked complete all as specified and directed.