Outsourcing of resources for management and operation of sewage treatment plant at Air Force Station Jaisalmer

Amount

Schedule 'A' Part-I General Note as applicable for serial item No 2.00 of BoQ/Sch 'A' Contractors attention is hereby invited that estimated cost of serial item No 2.00 is Rs. 4,82,400.00 based on prevailing rates of Schedule of Minimum fair wages. Quoted amount against serial item No. 2.00 is less than the amount the work (Estimated of serial item No. 2.00 of BoQ/Sch 'A') then lowest bidder will have to deposit FDR in favour of Accepting Officer within 07 days from financial bid opened difference in Estimated cost & quoted amount of serial item No. 2.00 before evaluation of financial bid for acceptance of tender, failing which lowest tender will not be accepted. FDR submitted at the time of Acceptance of bidder will be realesed only after satisfactory proof of payment of deployed person under the respective serial item No. 2.00 of BoQ.

Manning and Operation of Sewage Treatment Plant of Capacity 1.5 MLD at AF Stn Jaisalmer One Skilled labour (FGM) in two shifts (each shift will be of 8 hours i.e. total 16 hours) (including Sunday/Holiday) including operation of DG Set, Electric Supply Installations, day to day maintenance such as cleaning the surrounding area of installation building (inside/outside) , maintenance of motor, starter and panel board regularly. All valves to be operated concerned with installation on requirement basis all as directed at site by Engr-in-Charge. Notes: (a) Wage paid by the contractor to the persons employed shall not be less than the minimum wages fixed by State/Central Government from time to time whichever is higher. The payment shall be made to the workers through a nationalised bank and the bank statement of fair wages as per minimum labour wages as mentioned above shall be submitted along with the RARs/FB for payments.

Notes (Contd...): (b) The contractor shall be responsible for the EPF, ESI, bonus, Safety etc. and insurance of all trademen employed by him as per existing Labour Rules/Acts/Regulations (c) Contractor special attention is invited that payment of operator / labour shall be made only through Account payee cheque and same shall be deposited in Adhar link account of operator / labour. Documentary evidence for the same shall be submitted to Engineer -in-Charge before payment of RAR / Final bill. (d) Contractor and his personnel detailed for management and operation of Sewage Treatment Plant shall be responsible for serviceability of Pumpset, Diesel engine generating set, Valves. In case of any major fault occurs in above mentioned items, he will be report directly to concerned JE E/M / AGE E/M. Person deputed for operation will be responsible for minor maintenance such as checking of oil, checking of Diesel, oiling and greasing of Valves,Drawing disinfectant from MES and pouring it to dozing system to maintained required PPM level as per IS norms, informing MES and maintaing sufficient balance in storage tank for DG set as and when required, checking of battery terminal and cleaning of DG Sets,Pumpset, Valves cleaning of Sewage Treatment Plant and including its surrounding area complete.

Notes (Contd...): (e) Necessary weekly off will be given to manpower employed for this schedule as per existing rules and regulation of state /central govt. and necessary replacement will be provided by the contractor. Rates quoted for this schedule shall deemed to be included this provision. (f) In case absence of any operator / workmen from any shift will be penalized with a penalty of double the rate quoted by the contractor in addition to the shift not taken in to consideration for payment. Attendant / Operator wanting leave will get it sanctioned before proceeding on leave along with the name of individual who will be performing his duty/shift in his absence. No replacement of operator/workmen without the knowledge of department will be allowed. (g) Safety equipment's, tools and first aid kit will be provided to all tradesman without any extra cost to government. (h) Log book (Sheet), Muster roll, duty roster, fuel consumption register, daily breakdown register, attendance register and other requisite registers shall be maintained by operator and get it signed by concerned JE, Engineer-in-charge and contractor on daily basis and same shall be submitted monthly to accepting officer for inspection and other details as specified in PS.

Notes (Contd...): (j) Log book (Sheet), Muster roll, duty roster, fuel consumption register, daily breakdown register, attendance register and other requisite registers shall be maintained by operator and get it signed by concerned JE, Engineer-in-charge and contractor on daily basis and same shall be submitted monthly to accepting officer for inspection and other details as specified in PS (k) Operator should be ITI certificate in respective trade with minimum 05 years experience for running of installation and well conversant with the Pump set equipment's with connected panel and opeartion of DG set and must produce qualification and experience certificates duly attested by gazetted officer. The attested certificate shall be submitted to accepting officer at the time of commencement of work. (l) It is the responsibility of the contractor to ensure that the Sewage is reaching from Sewage Pumping Station to Central Sewage Treatment Plant and the contractor shall make the arrangement for cleaning the Sewage Pipe Line by deploying the Sewage Tanker and Flushing the sewage choked in the Sewage Line with water pressure.

Schedule 'A' Part-II M&L for testing of Sewage Water {(Stilling chamber (Inlet)} and Treated Water (Outlet) sample at authorised government laboratory for biological fitness of water (pH Value, total Suspended Solids, Biological Oxygen Demand (BOD), Chemical Oxygen Demand (COD), total Residual Chlorine, total Coliform) on quaterly basis including glass bottle for collection of sample complete all as specified.

Supply and provide (Calcium hypo chloride) 65%-70% chlorine including anti corrosive agent content Liquid desinfectant for Sewage treatment plants much more stable than chlorine gas & stronger than bleaching powder and sodium hypo chloride packed in 50 Kg drum complete as directed by Engineer-in-Charge. Make : Vasu, Corrocil-D-2000 or equivalent of Auafit/ Altoch(declibec) or Equivalent. Note: Test Certificate from government certified lab for each batch of chlorine to be submited at the time of delivery.

S&F 1000 Litre capacity Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including dismentling & taking down old unserviceable water tank capacity 1000 litre complete as specified in SSR Part-I.

S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including dismentling & taking down old unserviceable water tank capacity 500 litre complete as specified in SSR Part-I.

M&L for Cleaning of following Sewage Treatment Plant Chambers by professional agency after De-watering of sewage and cleaning with Jet Pressure Water Pump for dirt, silt and agae, scrapping with steel brushes/ hessin cloths of the chamber walls from inside including floor of the chamber and apply solution of Potassium Permanganate (KMnO4) complete and providing two coats of anti corrosive paint including watering etc and repair to vent pipes including providing wire mesh and clamps complete all as specified and directed by Engineer-in-Charge. Note: If work is not done upto satisfaction level of concerned JE/AGE (E/M), the work will be redone upto the required level without any extra cost. Necessary tools and safety measures for man power to be arranged by contractor.

Stilling Chamber of size 1.40 x 1.40 x 1.40 m.

Pumping Station Plant at Central Sewage Treatment Plant.

Grit Chamber of size 3.6MX1.2MX1.1 M

Equalization Tank of size 8.30 M (Dia) x 3.50 M

Moving Bed Bio Reactor of size 4.00 M (Dia) x 5.00 M

Tube Settler of size 7.00 M x 6.50 M x 2.70 M

Chlorine Contact Tank of size 7.00 M x 4.50 M x 2.00 M

Sludge Holding Tank of size 8.10 M (Dia) x 2.50 M

Treated Water Tank of size 13.50 (Dia) x 6.00 M

M&L for Pebbles, gravels, Silex (Silica) and sand of following sizes for Dual Media Filter of Sewage Treatment Plant, premixed for filling into vessel and cleaning the around area and repacking the vessel after filling in new items complete by means of packing and fixing material including labour and testing for appropriate pressure complete all as specified and directed by Engr-In-Charge.

Pebbles of size 40-20mm

Pebbles of size 20-12mm

Pebbles of size 12-6mm

Pebbles of size 10-3mm

Crushed Gravel of size 6-3mm

Fine Sand of size 16/32

Coarse Silex (Silica)

Fine Silex (Silica)

M&L for Activated Granular Carbon for filling into Activated Carbon Filter of Sewage Treatment Plant including draling out the existing used Charcoal from Filter vessel and cleaning the around area and repacking the vessel after filling in new items complete by means of packing and fixing material including labour and testing for appropriate pressure complete all as specified and directed by Engr-In-Charge. Note: Rates includes for taking down also.

S&F in bourdon type glyserin filled pressure gauge (150mm dia) complete with siphon tubewith isolating cock having range of 0 to 7Kg/Cm2 as per IS 8793 complete all as specified and directed by Engr-in-Charge. Make : H Guru Model No. 6PSSSW2 or equivalent.

M&L for Tube Deck Media of size 100mm/150mm X 750mm/1000mm (as per sample) for Tube Settler Chamber as per sample complete all as specifie and directed.

MBBR Media Virgin PP UV stablilized based media with size of 16x22mm/ 17x24mm with removal performace of 30 BOD complete all as specified and directed by Engr -in-Charge.

S&F Chlorine Dozing pump 0-6 LPH with flow of 4 KG/CM2 complete with all fittings and fixtures complete all as specified and directed by Engineer-in-Charge. Make : Aventura Model No- Micro V.1.4 or equivalent.

M&L for Servicing of blower of capacity 760 Cum/Hour with pressure 0.65 Kg/SqCM of RPM 1000, including replacement of Paper filter of blower of Make : Everest Model M-710 complete all as specified and directed. Note All necessary Tools & Plants required for servicing to be included in quoted rates.

M&L for Servicing of Decanter Centrifuge including greasing of Bearing at Feed/ Slurry end and Main Bearing at Liquid discharge, Cleaning of Scroll/ Conveyor, Bowl, Pump blades complete by authorised OEM manufacturer of Make : Alfa Laval. Note All necessary Tools & Plants required for servicing to be included in quoted rates.

S&F V Belt , Heat and Oil resistant of Model SP13, 2150 complete all as specified and directed. MAKE : FENNER or equivalent.

M&L for opening and reassembling of submersible motor after rewinding and replacement of worn out spare parts including taking out the burnt winding wire and rewinding of submersible motor following capacity with new PVC insulated solid copper conductor (wire) superior quality of approved make, gauge/size & number of wire as per existing including insulation material and for suitable RPM including rotor balancing, minor spares, fixing new mechanical seal for avoiding of shorting of motor and replacement of unserviceable spare parts and reassembling the components & testing for function ability including taking including taking old unserviceable motor from treated water tank complete all as specified and directed by Engr-in-Charge. Note: The Job include the opening of motor at site for damaging of existing stator winding if found burnt/damaged in front of concerned JE/AGE (E/M) after testing on site before taking to work shop outside MD land. Motors will be given for repairing as per the site condition and need for repair being maintenance work.

Submersible motor of capacity 60 HP, 3 phase, 415 volts

Submersible motor of capacity 25 HP, 3 phase, 415 volts

Submersible motor of capacity 10 HP, 3 phase, 415 volts

Submersible motor of capacity 7.5 HP, 3 phase, 415 volts

M&L for opening and reassembling of monoblock /centrifugal pump (motor) after rewinding and replacement of worn out spare parts including taking out the burnt winding wire and rewinding of monoblock/ centrifugal pump (motor) following capacity, Three Phase, 415 volts with new PVC insulated solid copper conductor (wire) superior quality of approved make, size & number of wire as per existing including insulation material, minor spares and replacement of unserviceable spare parts and reassembling the components & testing for function ability, complete, all as specified & directed. Note: (i) The include opening of motor at site for damaging of existing stator winding if found burnt/damaged in front of concerned JE/AGE (E/M) after testing on site before taking to work shop outside MD land and testing of RPM to be done after installation on Ground after rewinding. Motor will be given for repairing as per the site condition and need for repair being maintenance work. (ii) Unit rate (quoted by the tenderer) shall be deemed to include for all minor spares/extras. The decision of Accepting officer regarding minor spares/extras shall be final, conclusive and binding.

Monoblock/Centrifugal motor of capacity 40 HP, 3 phase, 415 volts

Monoblock/Centrifugal motor of capacity 12.50 HP, 3 phase, 415 volts

Monoblock/Centrifugal motor of capacity 7.50 HP, 3 phase, 415 volts

Monoblock/Centrifugal motor of capacity 1.50/2.0 HP, 3 phase, 415 volts

S&F in replacement Deep Groove ball/roller bearing (Double sealed ball bearing) for the following capacity Pump (Primary and secondary). Make : SKF/NBC/TATA/FAG/UBC. Note: The rates include cost of two nos bearing as per pump design. Both the bearings(as per pump make) to be replaced at the same time.

Centrifugal pump/mono block pump set of capacity 40 HP

Centrifugal pump/mono block pump set of capacity 12.5 HP

Centrifugal pump/mono block pump set of capacity 7.5 HP

Centrifugal pump/mono block pump set of capacity 1.5/2.0 HP

M&L in replacement of Centrifugal/Monoblock Pump motor MS coupling capacity 40 HP motor (Beam, Jaw, Gear any type) complete all as specified and directed by Engineer-in-Charge.

M&L in replacement of Centrifugal/Monoblock Pump motor MS coupling capacity 12.5 HP motor (Beam, Jaw, Gear any type) complete all as specified and directed by Engineer-in-Charge.

M&L in replacement of Centrifugal/Monoblock Pump motor MS coupling capacity 7.5 HP motor (Beam, Jaw, Gear any type) complete all as specified and directed by Engineer-in-Charge.

M&L in replacement of Centrifugal/Monoblock Pump motor MS coupling capacity 1.5/2.0 HP motor (Beam, Jaw, Gear any type) complete all as specified and directed by Engineer-in-Charge.

Induction Motor prelubricated ZZ bearing (DE and NDE) for capacity 40 HP motor (Primary and secondary). Make : SKF/NBC/TATA/FAG/ UBC. Note: The quoted rates include cost of two nos bearing as per motor design. Both the bearings(as per motor frame type) to be replaced at the same time.

Induction Motor prelubricated ZZ bearing (DE and NDE) for capacity 12.5 HP motor (Primary and secondary). Make : SKF/NBC/TATA/FAG/ UBC. Note: The quoted rates include cost of two nos bearing as per motor design. Both the bearings(as per motor frame type) to be replaced at the same time.

Induction Motor prelubricated ZZ bearing (DE and NDE) for capacity 7.5 HP motor (Primary and secondary). Make : SKF/NBC/TATA/FAG/ UBC. Note: The quoted rates include cost of two nos bearing as per motor design. Both the bearings(as per motor frame type) to be replaced at the same time.

Induction Motor prelubricated ZZ bearing (DE and NDE) for capacity 1.5/2.0 HP motor (Primary and secondary). Make : SKF/NBC/TATA/FAG/ UBC. Note: The quoted rates include cost of two nos bearing as per motor design. Both the bearings(as per motor frame type) to be replaced at the same time.

S&F in replacement Contactor for capacity 40 HP, Motor Starter (Amp rating as per site requirement) including removing of exiting burnt and unserviceable contactor and cleaning of carbon complete all as specified and directed. Make: Havells/L&T/BCH

S&F in replacement Contactor for capacity 12.5 HP, Motor Starter (Amp rating as per site requirement) including removing of exiting burnt and unserviceable contactor and cleaning of carbon complete all as specified and directed. Make: Havells/L&T/BCH

S&F in replacement Contactor for capacity 7.5 HP, Motor Starter (Amp rating as per site requirement) including removing of exiting burnt and unserviceable contactor and cleaning of carbon complete all as specified and directed. Make: Havells/L&T/BCH

S&F in replacement Contactor for capacity 1.5/2.0 HP, Motor Starter (Amp rating as per site requirement) including removing of exiting burnt and unserviceable contactor and cleaning of carbon complete all as specified and directed. Make: Havells/L&T/BCH

S&F in replacement motor starter relay for capacity 40 HP, Motor Starter (Amp rating as per site) including removing of exiting burnt/US relay complete all as specified and directed by Engr-In-Charge.

S&F in replacement motor starter relay for capacity 12.5 HP, Motor Starter (Amp rating as per site) including removing of exiting burnt/US relay complete all as specified and directed by Engr-In-Charge.

S&F in replacement motor starter relay for capacity 7.5 HP, Motor Starter (Amp rating as per site) including removing of exiting burnt/US relay complete all as specified and directed by Engr-In-Charge.

S&F in replacement motor starter relay for capacity 1.5/2.0 HP, Motor Starter (Amp rating as per site) including removing of exiting burnt/US relay complete all as specified and directed by Engr-In-Charge.

S&F in replacement DOL starter with wide band coil, Phase reversal preventation, Phase imbalance preventation, single phase protection, Auto/Manual mode of capacity 7.5 HP motor including dismantling & taking out old unserviceable DOL starter complete all as specified and directed by Engineer-in-Charge. Make : BCH/Legrand/ABB/L&T

S&F in replacement DOL starter with wide band coil, Phase reversal preventation, Phase imbalance preventation, single phase protection, Auto/Manual mode of capacity 1.5/2.0 HP motor including dismantling & taking out old unserviceable DOL starter complete all as specified and directed by Engineer-in-Charge. Make : BCH/Legrand/ABB/L&T

M&L for oiling and greasing of pump motor parts (any make any size any type) by means of greasing gun or manually by unbolting and separating the pump motor set at pump house inside defence area completely for smooth operation of machinery including replacement of nut, bolts, washers of appropriate size as per site requirement and motor pump size complete making it leakage free and applying gland packing of necessary quantity and thickness and making working complete noise and leakage free and refixing in same original position complete all as specified and directed by Engineer-in-Charge. Note: Rates for greese, lubricating oil and gland packing deemed to be included in quoted rates by the tenderer.

S&F electronic type Single Phase Preventor suitable for 3 Phase, 415 Volt, motor VSP-2/3 of any make and any size complete as per sample including disconnecting & taking down old unserviceable Single Phase Preventor, complete all as specified and directed by Engineer-in-Charge. Make : C&S/Havells/ABB/L&T

M&L for preparation of existing old painted surface of any description such as Panels at any height and painted inside and outside (strictly existing shade) complete after scratching existing rusted surface then applying one coat of primer (superior quality) and in blue colour all around the panels and plinth complete all as directed. (Make of Paint : Asian/Berger or equivalent)

M&L for demolishing old existing broken Earth pit chamber and prepare new Earth pit chamber as per site requirement and including putting CI cover complete all as specified and directed by Engr-In-Charge. Note: Contractor shall be responsible for removing debris of old PCC chamber from site.

S&F 6 sqmm multistranded copper conductor, 3 core PVC insulated and sheathed copper 1100 Volts grade submersible flat cable fixed to submersible motor with suitable clamps & jointing material complete including disconnecting & taking out old unserviceable cable complete all as specified and directed. Make : Havells or equivalant model of Finolex/Polycab.

S&F 10 sqmm multistranded copper conductor, 3 core PVC insulated and sheathed copper 1100 Volts grade submersible flat cable fixed to submersible motor with suitable clamps & jointing material complete including disconnecting & taking out old unserviceable cable complete all as specified and directed. Make : Havells or equivalant model of Finolex/Polycab.

S&F 16 sqmm multistranded copper conductor, 3 core PVC insulated and sheathed copper 1100 Volts grade submersible flat cable fixed to submersible motor with suitable clamps & jointing material complete including disconnecting & taking out old unserviceable cable complete all as specified and directed. Make : Havells or equivalant model of Finolex/Polycab.

S&F 35 sqmm multistranded copper conductor, 3 core PVC insulated and sheathed copper 1100 Volts grade submersible flat cable fixed to submersible motor with suitable clamps & jointing material complete including disconnecting & taking out old unserviceable cable complete all as specified and directed. Make : Havells or equivalant model of Finolex/Polycab.

M&L in repair for Earthing complete with galvanished earth plate electrode 60cm x 60cm x 6mm thick burried directly in ground (earth pit not less than 2.25m deep below ground level) with top edge of plate not less than 1.5 deep below normal ground level and connected to galvanished iron earth lead strip 32mmx6mm upto 7.50 metre, by means of GI nuts, bolt, check nuts, washers, thimbles, etc as shown in electrical plate No 03 SSR Part-I and connection to main switch board or panel and testing on completion including excavation and earth work in any type to soil, returning fitting in and removal of surface spoil to a distance not exceeding 50 metre, PCC chamber (1:3:6) type C-2, charcoal and salt mixed layer 15cm thick all around the earth plate electrode, MS funnel with wire mesh, GI pipe light grade 20mm bore for watering and 40mm bore GI pipe medium grade for earth wire protection fixed with poles with two clamps, made from MS flat 25mm x 3mm, bolts, nuts and washers 75mm thick RCC cover 1:2:4 type B-1 shall be provided on CI frame etc complete all as specified. Note :- PCC chamber shall be constructed at least 1.5m away from the earth electrode. The pipe for watering shall be provided in slanting manner.

S&F in replacement of Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 32 x 6mm copper strip complete all as specified. Note : Nut, bolt and other items included in quoted rate by the tenderer.)

M&L for Test point terminal block made of MS powder coated MS Sheet of 1.6mm thick sheet of size 230X230X75mm drilled and screwed including terminals for two strips entry and exit with overlapping for testing earth result complete all as specified and directed by Engr -In-Charge.

S&F in replacement of MCCB 4 Pole, 400 Amps, 415 Volts, adjustable type with breaking capacity 36 KA complete all as specified and directed. Make : Havells or equivalent of legrand/L&T/ABB/HPL/C&S

S&F in replacement of MCCB 4 Pole, 200 Amps, 415 Volts, adjustable type with breaking capacity 36 KA complete all as specified and directed. Make : Havells or equivalent of legrand/L&T/ABB/HPL/C&S

S&F in replacement of MCCB 4 Pole, 160 Amps, 415 Volts, adjustable type with breaking capacity 36 KA complete all as specified and directed. Make : Havells or equivalent of legrand/L&T/ABB/HPL/C&S

S&F in replacement of MCCB 4 Pole, 100 Amps, 415 Volts, adjustable type with breaking capacity 36 KA complete all as specified and directed. Make : Havells or equivalent of legrand/L&T/ABB/HPL/C&S

S&F in replacement of MCCB 4 Pole, 63 Amps, 415 Volts, adjustable type with breaking capacity 36 KA complete all as specified and directed. Make : Havells or equivalent of legrand/L&T/ABB/HPL/C&S

S&F in replacement of MCCB 4 Pole, 32 Amps, 415 Volts, adjustable type with breaking capacity 36 KA complete all as specified and directed. Make : Havells or equivalent of legrand/L&T/ABB/HPL/C&S

S&F in replacement of MCCB 3 Pole, 400 Amps, 415 Volts, adjustable type with breaking capacity 36 KA complete all as specified and directed. Make : Havells or equivalent of legrand/L&T/ABB/HPL/C&S

S&F in replacement of MCCB 3 Pole, 200 Amps, 415 Volts, adjustable type with breaking capacity 36 KA complete all as specified and directed. Make : Havells or equivalent of legrand/L&T/ABB/HPL/C&S

S&F in replacement of MCCB 3 Pole, 100 Amps, 415 Volts, adjustable type with breaking capacity 36 KA complete all as specified and directed. Make : Havells or equivalent of legrand/L&T/ABB/HPL/C&S

S&F MCB, SPN, 40 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA , 240 Volt grade, AC, 50 Hz and making connections using suitable size copper lugs/thimbles, including taking down old unserviceable MCB, complete, all as specified and directed by Engineer-in-Charge. Make : Havells or equivalent of legrand/L&T/ABB/HPL/C&S

S&F MCB, SP, 40 Amps rating, with over load and short circuit protection 'C' curve and rupturing capacity 10 kA , 240 Volt grade, AC, 50 Hz and making connections using suitable size copper lugs/thimbles, including taking down old unserviceable MCB, complete, all as specified and directed by Engineer-in-Charge. Make : Havells or equivalent of legrand/L&T/ABB/HPL/C&S

S&F non return valve (NRV) of size 100mm bore, cast iron body, as per IS 5312 (ISI marked), heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint including dismantling & taking out old unserviceable non return valve complete all as specified and as directed by Engineer-in-Charge.

S&F non return valve (NRV) of size 150mm bore, cast iron body, as per IS 5312 (ISI marked), heavy duty, both ends flanged and drilled, including nuts, bolts, washer and neoprene rubber gasket joint including dismantling & taking out old unserviceable non return valve complete all as specified and as directed by Engineer-in-Charge.

S&F in replacement liquid level controller for Overhead and Underground tank with six sensors for 3 Phase motor flow sensor with auto restart delay facility complete all as specified and directed.

S&F cast iron body sluice valve heavy duty class ‘PN-1.6’, 65mm bore, ISI marked with confirming to IS-14846-2000, both flanged ends and drilled, high tensile stainless steel spindle, Cast Iron gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable sluice valve of 65mm bore, complete all as specified & directed. Make : Kirloskar/L&T/Leader/Venus

S&F cast iron body sluice valve heavy duty class ‘PN-1.6’, 80mm bore, ISI marked with confirming to IS-14846-2000, both flanged ends and drilled, high tensile stainless steel spindle, Cast Iron gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable sluice valve of 80mm bore, complete all as specified & directed. Make : Kirloskar/L&T/Leader/Venus

S&F cast iron body sluice valve heavy duty class ‘PN-1.6’, 200mm bore, ISI marked with confirming to IS-14846-2000, both flanged ends and drilled, high tensile stainless steel spindle, Cast Iron gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable sluice valve of 150mm bore, complete all as specified & directed. Make : Kirloskar/L&T/Leader/Venus

S&F cast iron body sluice valve heavy duty class ‘PN-1.6’, 250mm bore, ISI marked with confirming to IS-14846-2000, both flanged ends and drilled, high tensile stainless steel spindle, Cast Iron gate with brass ring, non rising type, cast iron wheel handle, cast iron cap, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable sluice valve of 250mm bore, complete all as specified & directed.

S&F reflux valve of size 250mm bore with by pass arrangement and testing, including dismantling & taking out old unserviceable valve of 250mm bore, complete all as specified & directed.

S&F as in replacement Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 40mm bore or brass ferrule and fixed complete all as specified and as directed.

S&F as in replacement Ball brass valve, high pressure, with polythene float and flynut complete, screwed for iron pipe 65mm bore or brass ferrule and fixed complete all as specified and as directed.

S&F cast iron body butter fly valve heavy duty, 100mm bore, ISI marked with confirming to IS, both flanged ends and drilled, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable sluice valve of 100mm bore, complete all as specified & directed.

S&F cast iron body butter fly valve heavy duty, 150mm bore, ISI marked with confirming to IS, both flanged ends and drilled, complete with 3mm thick neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, and testing, including dismantling & taking out old unserviceable sluice valve of 150mm bore, complete all as specified & directed.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable (ISI marked) with aluminium stranded conductor 1100 Volt grade cross sectional area 50 sqmm 3.5 core laid in trenches/ducts, through pipe, under floors or roads/along poles etc including taking down old unserviceable cable complete all as specified and directed. Make : Havells or equivalant model of Finolex/Polycab.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable (ISI marked) with aluminium stranded conductor 1100 Volt grade cross sectional area 25 sqmm 3.5 core laid in trenches/ducts, through pipe, under floors or roads/along poles etc including taking down old unserviceable cable complete all as specified and directed. Make : Havells or equivalant model of Finolex/Polycab.

Supply, laying, jointing and testing XLPE insulated armoured heavy duty LT under ground electric cable (ISI marked) with aluminium stranded conductor 1100 Volt grade cross sectional area 16 sqmm 4 core laid in trenches/ducts, through pipe, under floors or roads/along poles etc including taking down old unserviceable cable complete all as specified and directed. Make : Havells or equivalant model of Finolex/Polycab.

M&L in replacement nominal area of conductor 2.50 sqmm PVC cable, 2 core, insulated and (Flame Retardant) FR PVC round sheathed, Copper Conductor (flexible) industrial cable, 1100 Volt, conforming to IS 694 complete all as specified and directed by Engr-in-Charge. Make : Havells Cat Part No. WHMFDSKB22X5 or equivalent of Finolex/RR Kabel. (Note :- Two run for Phase and Neutral shall be treated at One run).

S&F LED street light 90 Watt made up of pressure die cast housing with toughned glass and individual high power LEDs with secondary optics, IP 66 protection and impact resistance of IK07 including taking down old unserviceable LED street light complete all as specified and directed. Make : Havells Cat Part No. ENDURACITYLINER NEOSL90WLED757SASYBOTG or equivalent of Philips/ Crompton Greaves.

Supplying, laying jointing, commissioning & testing DI pipes with rubber gasket Tyton Joints of spigot and socket ends centrifugally cast (spun) class "K-7" conforming to IS-8329 -2000 in any length of size 100mm bore laid in trenches ncluding taking up or down old unserviceable CI/DI water tubing and connections of 100mm bore complete all as specified and directed by Engineer-in-Charge.

Supplying, laying jointing, commissioning & testing DI pipes with rubber gasket Tyton Joints of spigot and socket ends centrifugally cast (spun) class "K-7" conforming to IS-8329 -2000 in any length of size 150mm bore laid in trenches ncluding taking up or down old unserviceable CI/DI water tubing and connections of 150mm bore complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing CI/DI fitting upto 150mm bore pipe line for reducing/bends (any type radius and angle) tapers any type, staright, bend, increasing, decreasing or double socket extra Tee pieces single branch Ý'Junction, double branch, cross collars caps etc complete all as specified and as directed.

Supply, laying and joing (By butt fusion welding method) in standard length BIS marked (high density polyethylene Pipe) HDPE pipe suitable for potable water as per IS specification No 4984/1995 (Pressure rating 6 Kg/Cm2 PE-100) and fittings (HDPE specials suitable to HDPE pipes) including taking down old unserviceable pipe complete all as specified and directed by Engr-in-Charge.

25mm nominal dia HDPE Pipe (Outer Dia)

40mm nominal dia HDPE Pipe (Outer Dia)

63mm nominal dia HDPE Pipe (Outer Dia)

90mm nominal dia HDPE Pipe (Outer Dia)

125mm nominal dia HDPE Pipe (Outer Dia)

160mm nominal dia HDPE Pipe (Outer Dia)

180mm nominal dia HDPE Pipe (Outer Dia)

200mm nominal dia HDPE Pipe (Outer Dia)

250mm nominal dia HDPE Pipe (Outer Dia)

M&L for rectification of Leakages by necessary excavation (upto one length of 6.00 RM) in any type of soil, in any situation/depth including bailing out leakage water by suitable measures, repair to DI/CI/ HDPE of following sizes pipe with MS clamp including rubber cushioning, 3mm thick and 300mm wide with hole drilled for nutbolts including suitable nuts and bolts for rectification of leakages complete all as specified and directed. Note: Cost of JCB for lifting of pipe for repair will be part of quoted rates.

25mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

40mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

63mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

90mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

125mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

160mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

180mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

200mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

250mm nominal dia HDPE/ GI/CI/DI Pipe (Outer Dia)

M&L in replacement Non clog Centrifugal Pump Set with Motor of capacity 7.5KW/10 HP with suction and delivery size 100mm, 415 volts with solid handling capacity 18.5mm size with rate speed 1450 RPM complete all as specified and directed by Engineer-in-Charge.

S&F in replacement suction hose pipe of size 100mm dia with bending radius 213mm heavy duty, working pressure 4Kg/Sqcm complete all as specified and directed by Engineer-in-Charge. Make : Flaxima or equivalent.

S&F in replacement delivery hose pipe of size 100mm dia with bending radius 290mm meduim duty, working pressure 3.5Kg/Sqcm complete all as specified and directed by Engineer-in-Charge. Make : Flaxima or equivalent.

Excavation in trenches, not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for foundation, pipe lines etc or for shafts, wells, cesspits, manholes, etc not exceeding 10 sqm area on plan and not exceeding 1.5 metre in depth and getting out in soft/loose soil complete all as specified.

All as per above item No. 89.00 but exceeding 1.50m deep and not exceeding 3.00 m deep.

All as per above item No. 89.00 but exceeding 3.00m deep and not exceeding 4.50 m deep.

All as per above item No. 89.00 but exceeding 4.50m deep and not exceeding 6.00 m deep.

Returning, filling in including in spreading, leveling, watering and well ramming in layers not exceeding 25 cm complete all as specified and directed by Engineer-in-charge.

Removal of excavated soil/ material to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.50 metre above the starting point complete all as specified

Removal of excavated soil/ material to a distance exceeding 250 metre but not exceeding 500 m and depositing where directed at a level not exceeding 1.50 metre above the starting point complete all as specified

M&L for dry sand to underground cable provided with a layer of 8cm deep before laying cable and 15cm after laying of cable and punned to 18cm after laying of cable and cover for protection of underground cable complete all as specified and directed. Notes :- (i) Approved dry sand free from vegetations, grass and other deleterious substances shall be used. (ii) For the purpose of payment only punned thickness shall be measured.

M&L for 40 to 50 mm thick rough dressed Jodhpur type stone slab 25 to 35cm width and 80cm long laid dry abutting each other for protection to under ground cable including dismantling & taking out old unserviceable cable complete all as specified and directed.

M&L for Cement concrete Type B-1, 1:2:4 (20mm graded aggregate) in foundations, coping, filling and mass concrete for foundation of motor pump set complete by using 10mm thick MS Sheet of approprite size and welding proper size and length of bolt and nut in foundation for avoiding vibration at the time of operation of motor pump set complete with demolition of existing foundation and considering of alignment of motor pump set complete all as specified and directed by Engr-In-Charge

M&L for plain cement concrete (1:4:8) Type D-2 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete including necessary form work complete all as specified and directed.

M&L for Precast cement concrete 1:3:6, type C-1 (using 20 mm graded stone aggregate) block masonry with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6 complete all as specified

M&L for rendering 10 mm thick in cement and mortar (1:4) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

Supply only integral waterprofing compound ISI Marked.

Puncture to existing 100mm dia NP-2 pipe by making hole of minimum 100 mm dia size, dewatering of waste water including de-sludging of solid materials etc by mannually or machanically and dispose off the same out side AF Stn as directed, thereafter cleaning the line by rode and other means and make good damaged portion of pipe by repair with cement and other required material to seal affected portion complete all as specified.

Cleaning of manhole upto 2.00 m deep by bailing out sluge and water and removing the waste to a distance exceeding 2.00 Km outside AF Stn complete all as specified and directed by Engineer-in-Charge.

Cleaning of manhole exceeding 2.00m deep but not exceeding 4.00m deep by bailing out sluge and water and removing the waste to a distance exceeding 2.00 Km outside AF Stn complete all as specified and directed by Engineer-in-Charge.

Cleaning of manhole exceeding 4.00m deep but not exceeding 6.00m deep by bailing out sluge and water and removing the waste to a distance exceeding 2.00 Km outside AF Stn complete all as specified and directed by Engineer-in-Charge.

M&L for 150mm bore reinforced concrete pipe, class NP2, laid and jointed complete with collars all as specified & as directed.

M&L for 200mm bore reinforced concrete pipe, class NP2, laid and jointed complete with collars all as specified & as directed.

Material and labour PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

Material and labour PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in bedding to drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 200 mm bore pipe all as specified and as directed.

Cleaning of existing sewage line of 150mm bore & at any depth by roding for perfect running/flowing order without destruction by removing all blockages in the system and removing all spoil from the pipe line and making the line free from all obstacles including taking off and refixing of manhole covers and removing the silt/sludge & other deposits out side of MD land in covered van/trolley, complete, all as specified & directed.

Cleaning of existing sewage line of 200mm bore & at any depth by roding for perfect running/flowing order without destruction by removing all blockages in the system and removing all spoil from the pipe line and making the line free from all obstacles including taking off and refixing of manhole covers and removing the silt/sludge & other deposits out side of MD land in covered van/trolley, complete, all as specified & directed.

M&L for Jodhpur stone for lintels, beams and roofs, self faced, 7.50 to 10 cm thick complete all as specified and directed.

S&F mild steel work in framed work such as grills, gratings, framed guard bars etc. with ends of bars shouldered and/ or riveted, or forged into spikes, and in ladders, railings, frame of water tank etc.and similar work confirming to Fe- 290 Grade E-165.

M/s Rashid Mohammed

M/s Shree Construction Company

S.D. And Company