Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹25.5 LAccepted-AOC HM 324 PHASE IX SAS NAGAR MOHALI PB | ₹25.5 L | L1 | Accepted-AOC Lowest Bidder |
| 2 | L2₹26.4 LRejected-AOC 2076 2077 CHIRIMAR MOHALLA AMBALA CANTT 133001 HR | AMBALA | HARYANA | 133001 | ₹26.4 L | L2 | Rejected-AOC Other Than Lowest Bidder |
| Sl No | Description | Qty | Unit | M/S MATLOOB AHMED L1 | M/s REEDIT CONSTRUCTION L2 |
|---|---|---|---|---|---|
| 1.00 | Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc (up to 4th storey of building ) complete all as specified and directed by Engineer-in-Charge. | 482 | SQUARE METRE | 30 ₹14,460 | 20 ₹9,640 |
| 2.00 | Demolition of Cement concrete unreinforced as in Ground Floor and paving n. exc. 15cm thick (above or below G.L.) complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge. | 10 | CUBIC METRE | 300 ₹3,000 | 450 ₹4,500 |
| 3.00 | Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge. | 1 | CUBIC METRE | 650 ₹650 | 800 ₹800 |
| 4.00 | Demolition of RCC tank or stone/boulders masonary,bricks etc, built in Cement mortar or cement lime mortar including all quoins,arches,pillers etc but excluding ashlar facing etc including removing to out of MOD land complete all as specified. | 2 | CUBIC METRE | 2,000 ₹4,000 | 600 ₹1,200 |
| 5.00 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises complete all as specified and directed by Engineer-in-Charge. | 250 | SQUARE METRE | 15 ₹3,750 | 30 ₹7,500 |
| 6.00 | Taking down chowkhats or frames n.exc 1.5 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts complete all as specified and directed by Engineer-in-Charge. | 15 | EACH | 100 ₹1,500 | 120 ₹1,800 |
| 7.00 | Taking down chowkhats or frames exc 1.5 sqm but n.exc 4 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts etc complete all as specified and directed by Engineer-in-Charge. | 6 | EACH | 200 ₹1,200 | 130 ₹780 |
| 8.00 | Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge. | 15 | EACH LEAF | 60 ₹900 | 90 ₹1,350 |
| 9.00 | Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and refixing in the same opening complete all as specified and directed by Engineer-in-Charge. | 5 | EACH LEAF | 70 ₹350 | 80 ₹400 |
| 10.00 | Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc, removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge. | 7.8 | 10 SQUARE METRE | 200 ₹1,560 | 200 ₹1,560 |
Updated dates
Tender Value
₹25 L
EMD Value
₹50,000
Closing Date
11 Dec 2025, 6:00 pmClosed
GE CHANDIGARH
GE CHANDIGARH N AREA, PIN-160003
REPAIR/ MAINT/UPGRADATION OF WATER SUPPLY AND ELECTRIC SUPPLY INDOOR ND OUTDOOR INSTALLATIONS AND COMPREHENSIVE MAINT OF E/M ASSETS AT K AREA N AREA AND HALLOMAJRA UNDER GE CHANDIGARH.
2025_MES_739791_1
GE/CHD/T-52/2025-26
Open Tender
Civil Works
CHANDIGARH
Class E category a(i) for contractor enlisted in MES
8 documents required · 8 mandatory
₹500
GE CHANDIGARH
₹50,000
Yes
30 Jan 2026
14 Nov 2025
13 Dec 2025
14 Nov 2025
11 Dec 2025
29 Nov 2025
14 Nov 2025 - 20 Nov 2025
Amount
Taking down Cement plaster or cement lime plaster on brick or stone walls including raking out joints, hacking for key & scrubbing down with water etc (up to 4th storey of building ) complete all as specified and directed by Engineer-in-Charge.
Demolition of Cement concrete unreinforced as in Ground Floor and paving n. exc. 15cm thick (above or below G.L.) complete including disposal of unservicable rubbish outside Cantt area all as specified and directed by Engineer-in-Charge.
Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) as in roofs, floors (other than ground floors) beams, slabs, staircases, landing, chajjas and similar suspended work complete all as specified and directed by Engineer-in-Charge.
Demolition of RCC tank or stone/boulders masonary,bricks etc, built in Cement mortar or cement lime mortar including all quoins,arches,pillers etc but excluding ashlar facing etc including removing to out of MOD land complete all as specified.
Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.
Taking down chowkhats or frames n.exc 1.5 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts complete all as specified and directed by Engineer-in-Charge.
Taking down chowkhats or frames exc 1.5 sqm but n.exc 4 sqm each (without taking off shutter from the frame) and removing from the site including dismantling brick work of hold fasts etc complete all as specified and directed by Engineer-in-Charge.
Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and removing from the site complete all as specified and directed by Engineer-in-Charge.
Taking down shutters of any description exc 1 sqm each but not exc 2 sqm each and refixing in the same opening complete all as specified and directed by Engineer-in-Charge.
Dismantling Stone slabs and tiles of any description or thickness in floors, aprons etc, removing rubbish off the premises complete all as specified and directed by Engineer-in-Charge.
Dismantling of cast iron pipe/ PVC drain pipes/PVC (SWR) pipe etc, 110mm jointed in cement mortar and taking out of trenches and wall, if required complete all as specified and directed.
Dismantling of cast iron pipe/ PVC drain pipes/PVC (SWR) pipe etc, 75mm jointed in cement mortar and taking out of trenches and wall, if required complete all as specified and directed.
Dismantling wall and ceiling boards (fibre,pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete, all as specified and as directed by Engr-in-charge.
Dismanntling of plain or corrugated AC roof sheet, any gauge, thickness, including nainital or similar pattern roof covering etc complete all as specified and directed.
Taking up or down steel tubing and connections of 15mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.
Taking up or down steel tubing and connections of 20mm bore in pipe, including cleaning for re-fixing or removal from site to store complete all as specified and directed by Engineer-in-Charge.
Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones (up to 4th storey of building ) complete all as specified and directed by Engr-In-Charge.
M&L taking out roots of trees penetrated through valves/concrete/brick surfaces etc upto any depth by cutting chieseling , demolition of brick work , concrete work and pouring concentrated acids/Dr fixit chemicals upto the depth of roots and making good the disturbed portion complet all as specified and directed.
Installation of rebar by using Hilti hammer drill with carbide drill bit,chemical dispensing gun for inserting RE-500V3 chemical upto minimum depth of (10 x dia of bar ) as in chajja,beam,lintel,column slab and parapet at any height before inserting an anchor bar.Hole must be free from dust debris,water,oil grease complete all as per manufacturers instructions. Note :- (i) Reinforcement shall be measured and paid separately. (ii) Rates are inclusive of form work and safety measures. (iii) Dia of bar 10/12 mm
Disconnecting/dismantling existing tanks of capacity exc. 500 ltr & n. exc. 1000 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.
Disconnecting/dismantling existing tanks of capacity exc. 250 ltr & n. exc. 500 ltr, setting aside and removing from site complete all as specified and directed by Engineer-in-Charge.
Disconnecting existing tanks , setting aside (or lowering if required) for repair, cleaning, etc. and hoisting if required reconneecting and refixing in position (Cleaning repairing etc measured separately) exc 250 & n.exc 500 ltr in capacity complete all as specified
Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc(exc 250 & nexc 500 ltr), Complete all as specified and as directed
Demolition of brick work or stone/boulder masonary built in cement mortar incl all quions arches, pillar or any other descrption etc complete all as specified and directed by Engineer-in-Charge.
M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth on Brick wall complete all as specified.
S&F for tank Nipple suitable for HDPE water tank 20mm tank nipple cast iron min weight 45gms complete all as specified.
S&F for tank Nipple suitable for HDPE water tank 15mm tank nipple cast iron min weight 45gms complete all as specified.
S&F in repair Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed for 20 mm bore dia complete all as specified and directed.
S&F in repair Gun-metal, globe or gate valves, with iron wheel head, screwed both end for iron pipe and fixed for 15 mm bore dia complete all as specified and directed.
Supplying & fixing in repairs of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe 20 mm dia and (Minimum weight 200 mm - 210 gms ) complete all as specified and directed by Engineer-in-Charge.
25 mm thick Cement concrete (1:2:4) type B-0,using 12.5 mm graded mechanically crushed stone aggregate as in levelling concrete etc. complete all as specified and directed by Engineer-in-Charge.
75 mm thick, cement concrete type C-2, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, complete all as specified.Plinth protection shall be laid in 1:20 slope and joint filling sealed with bituminous sealing compound grade "A" .
M&L for providing cement concrete PCC (1:2:4), type B-0 using 12.5 mm graded aggregate as in fillets at corners specialy provided in roof curb, padding of fill the depresion and mantain etc simlar work with recron 125 gm per cement bage complete all as specified and directed.
Plain cement concrete (1:4:8) type D-2,using 40 mm graded stone aggregate as in foundations, filling and mass concrete, sub base to paver blocks etc complete all as specified and directed by Engineer-in-Charge.
Reinforced Cement Concrete Nominal mix ( 1:1.5:3) using 20mm graded mechanically crushed stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete including formwork complete all as specified and directed by Engineer-in-Charge.
TMT steel bars 10mm dia and over, of grade Fe-500D cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.
First quality Non - skid coloured Ceramic tiles 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors etc. set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desied shade, hardner, resin in the ratio of 8:1:2 laid over and inculding 15 mm thick screed in cement mortar (1:4) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.
First quality Non - skid coloured Ceramic tiles 9-10mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm as in floors etc. set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desied shade, hardner, resin in the ratio of 8:1:2 laid over and inculding 15 mm thick screed in cement mortar (1:4) and pointed in white or coloured cement to match the tiles complete all as specified and directed by Engineer-in-Charge.
Glazed ceramic coloured tiles 450 x 300 x 7mm thick on vertical surface such as skirting , dado etc. over and including 10 mm thick rendering in CM 1:4 thick set and jointed with 4mm spacer and grouting the joint of flooring with epoxy grout mix of organic coated filler of desied shade, hardner, resin in the ratio of 8:1:2 to match tiles complete all as specified and directed by Engineer-in-Charge.
M&L out door/parking tiles heavy duty for light traffic non skid, anti scratch, heavy grip, vitreous/semi vitreous coloured, unique designs tiles 8 to 10mm thick area of each tile of size 300mmX300mm, in floors, parking/outdoor tiles etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed in CM(1:4), complete all as specified and directed.
Rubber coated Chequered cement concrete tiles 300mmx300mmx25mm thick with grey cement and pigment, over and including 20 mm thick screed in Cement mortar 1:4 set jointed and pointed in neat cement slurry in floors complete, all as specified and as directed by Engineer-in-Charge.
60mm thick machine pressed precast concrete ( M-35 grade) prepolished rubberized moulded interlocking paver block manufactured in an automatic plant working on vibration and simultaneous hydraulic compression from top, with grey cement and pigment(Yellow & red) any shape and size confirming to IS 15658-2006 laid over and including 50 mm thick cushion of coarse sand & filling the joints after laying complete all as specified and as directed.
Granite 16-18 mm thick, (table rubbed and polished) in single piece (in one direction) machine cut, machine polished, bedded and jointed with adhesive suitable for granite/stone & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:3) screed, as in cooking platform, shelves, RCC counters, window cills & similar situations, complete all as specified and directed by Engineer-in-Charge.
Machine cut Kota stone slab flooring 20-22 mm thick,SIZE 55 CM x 55 cm laid over & including 15 mm thick screed bed in cement mortar 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge.
Machine cut Kota stone slab 20-22 mm thick as in skirting, dado and pillars etc , laid over & including 10 mm thick rendering in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (mirror finish) complete all as specified and directed by Engineer-in-Charge.
M&L for 16 to 18 mm thick green marble machine cut stone slab (table rubbed polished) as in cooking platform , jamb, cill, step & riser,tread etc setted and jointed with cement slurry and bedded over & including cement sand mortar (1:4), & pointed with white/ coloured cement including grinding, rounded and chamfered edges and granite polishing etc complete all as specified and as directed.
Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge.
Brick work with sub class 'B' bricks, class designation 100, old size bricks, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar 1:6 EXCEPT BRICKS complete all as specified and directed by Engineer-in-Charge.
Dismantling of brick tiles or terracing tiles single layer as on roof grouted in cement mortar including removed of any existing treatment complete all as specified and as directed.
Dismantlling Mud phuska in roofs, any thickness,including plastering and leeping (whether full thickness removed or only a part thereof) in any position including disposal of unservicable rubbish outside Cantt area complete all as specified and directed by Engineer in Charge.
M&L for rendering 15mm thick in cement plaster (1:4) mixed with water proofing compound @3% by weight of cement over brick/ concrete surface over roof padding green cement concrete with recron 125gm per cement bag finished even complete all as specified and directed by Engr-in-charge. Note- Water proofing compound to be paid seperately.
Water proofing roof treatment sunken portion using APP polymeric water proofing membrane minimum 3 mm thick and weighting not less than 3.6 Kg/Sqm black finish reinforced with non-woven polyster matt wt not less than 150 gms/Sqm with thermo fusable finish laid over compatible bitumen primer at the rate of 0.40 Ltr/Sqm over cleaned surface including parapet,applying a coat of blown bitumen 85/25 grade @ 1.2 kg per square metre over priming coat torching over laps with a propane or butan gas torch with a over lap of 100 mm at the side and 150 mm at the ends and sealing all as per manufacturers instructions incl wire brushing and cleaning the top surfaces of concrete, roof surfaces etc. with water including flashings and junction of parapets etc complete all as specified and directed.
Rendering 15 mm thick in cement mortar 1:6, on fair faces of brick or concrete surfaces , trowelled to even and smooth surface without using extra cement, complete all as specified and directed by Engineer-in-Charge.
Rendering 15 mm thick in cement mortar 1:4, on brick or concrete surfaces mixed with water proofing compound on top layer, trowelled to even and smooth without using extra cement, (up to 4th storey of building ) complete all as specified and directed by Engineer-in-Charge. NOTE: Water proofing compound shall be measured and paid separately.
Rendering 10 mm thick in cement mortar 1:3 as in ceiling/soffits of slabs/Chajja/ Sunshade finishing the plastered surface even & smooth without using extra cement etc complete all as specified and directed by Engineer-in-Charge.
Supply only liquid water proofing comound ISI Marked complete all as specified and directed.
Preparation of new plastered surfaces of wall and applying two coats of cement base paint on walls over and including a coat of primer (up to 4th storey of building ) including preparation of surface complete all as specified and directed.
Preparation of plastered or unplastered new surfaces of ceilings and applying three coats of white wash including preparation of surface complete all as specified and directed by Engineer-in-Charge.
Preparation of new plastered surfaces of wall and applying two coats of oil bound distemper on walls over and including a coat of primer and 1mm thick cement wall care putty including preparation of surface complete all as specified and directed.
Preparation of old plastered surfaces of wall and applying one coat of interior grade acrylic emulsion over a coat of primer on old walls as per manufacture instrcutions including properly filling the cracks with putty and finished even and smooth surface using mechanical roller/hand roller including preparation of surface complete all as specified and directed.
M&L for complete removal of existing treatment such as white wash, colour wash, synthetic enamel paint etc applying two coats of weather coat over one coat of primer coat of damp shealth to old plastered wall as per manufacture instrcution including properly filling the cracks with putty and finished even and smooth surface using mechanical roller/hand roller (up to 4th storey of building ) complete all as specified complete all as specified.
M&L for complete removal of existing surface and applying two coats of oil bound distemper over and including a coat of primer and 1mm thick cement wall care putty on wall surfaces (upto 4th story of bldg), complete all as specified and as directed.
Preparation of walls brooming down, applying wall care putty 1 mm thick etc (up to 4th storey of building ) complete all as specified and directed by Engineer-in-Charge.
Preparation of old Plastered or un-plastered surfaces of ceilings etc by brooming down or steel wire brushing, scrapping down smoke soot moulds, moss, efflorescence salts treating oil and greasy spots etc and applying one coat of white wash on ceilings/ old decorated surfaces complete all as specified and directed by Engineer-in-Charge.
M&L for complete removal of existing surface and and applying two coats of cement base paint on walls over and including a coat of primer including preparation of surface (upto 4th story of bldg), complete all as specified and directed.
Preparation of old plastered surfaces of wall and applying one coats of cement base paint on walls including preparation of surface (up to 4th storey of building ) complete all as specified and directed.
Preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer complete all as specified and directed by Engineer-in-Charge.
Preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge.
Factory made Pressed steel frames, confirming to IS, having profile 125 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.
Factory made Pressed steel frames, confirming to IS, having profile 105 x 60 mm , 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, and 100 mm size hinges, lock strike plate, etc., with one shop coat of zinc chromate primer and fixing complete all as specified and directed by Engineer-in-Charge.
30 mm thick factory made Flush shutters, solid core construction, with particle core and plywood face panels, commercial type on both sides 1mm thick mica face covered with decorative face veneer with lipping/frame to match supplied and fixed complete all as specified and directed by Engineer-in-Charge.
Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles),With Wood free EPS with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification to be fitted in the MS frame welded/scaled to the stiles & rail with suitable PVC sheet beading & jointed together with solvent cement supply & fixing in the frame at site as per specification & drawing.
35 mm thick factory made glazed & Skeleton shutters of 2nd class Hardwood open rebated & prepared to receive glass or gauze etc without sash bar open rebated with edges of framing plain, chamfered or rounded, fitted with cut & mitred beads for securing glass or guage etc size ofstiles rails etc as specified in sec 8 clause 8.24 (a) of SSR Part-I (2009) complete all as specified and directed by Engineer-in-Charge.
Solid PVC door frames of size 50mm x 47 mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube, and edges will be painted to match with printed sheet, supply & fixing in opening as per specification & drawing complete all as specified and directed by Engineer-in-Charge.
Factory made box type steel windows with pressed steel frame min 1.25 thick complete including mild steel acessories like lugs, door stopper, holdfasts, pintol hinges, handles( minimum One for each shutter), and ISI marked tower bolt 150mm size (minimum 2 for each shutter) etc. with glazing bars and without glazing bars (Double shutter ) dovetailed or welded with one shop coat of zinc chromate primer, complete all as shown on drawing No. TD-276(R), Sheet No 1/4 to 2/4, 3/4, 4R/4 and as specified and directed by Engineer-in-Charge. Note: (i) Fabrication as per TD-276 (R) SH 1/4 to 2/4, 3/4, 4 (R) /4 (ii)Mode of measurement Unit will be for the complete window except Glass/ Gauge but incl fittings, ISI marked iron mongery complete as per TD. (iii) The PCC back filling in chowkhat of window, Grills,Sheet glass and wire gauge will be measured and paid separately against respective items.
Factory made box type steel ventilator with top hung or fixed half glass and half wire mesh portion shutter including projecting type hinges, steel peg stay, complete all as specified and directed by Engineer-in-Charge.Note:Sheet glass and wire gauge will be measured and paid separately against respective items
M&L for steel rolling shutters , (with lath thickness 1.25 mm ) with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and , erected in position as indicated, complete push pull or manual type gear operated type with bevel gear box and crank handle in repair complete all as specified and directed by Engineer-in-Charge.
Aluminium anodised,barrel tower bolts of extruded section with length of bolt 150 mm and dia of bolt not less than 10 mm,ISI marked complete all as specified and directed by Engineer-in-Charge.
100 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed by Engineer-in-Charge.
300 mm long,Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified & directed by Engineer in Charge.
150 mm long Aluminium handles, cast type,anodised complete all as specified and directed by Engineer-in-Charge.
125 mm long Aluminium handles, cast type,anodised complete all as specified and directed by Engineer-in-Charge.
Floor door stopper of aluminium alloy body and tongue, anodised,with hard drawn steel spring,fixed in floor with overall length of cover plate 150 mm complete all as specified and directed by Engineer-in-Charge.
S&F in repair Continuous (piano hinges) 30mm width of flap in repairs Paino hinges, mild steel bright finish (width of flap 30mm) complete all as specified and directed by Engineer-in-Charge.
S&F in repair 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, bright finished complete all as specified and directed.
Aluminium body peg set of 06 pegs complete all as specified and directed by Engineer-in-Charge.
M&L for door closer hydraulically regulated, designation No. 1 universal type, aluminium body suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed complete all as specified and directed.
Stainless steel wire cloth 0.63mm nominal dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.
Sheet glass 4 mm thick, ordinary quality and glazing with linseed oil pane putty & spring glazing clips using Silicon for fixing of glass in addition to glazing putty, in squares not exceeding 0.5 Sq. mtr in each pane complete all as specified and directed by Engineer-in-Charge.
4 mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm each and using Silicon for fixing of glass in addition to glazing putty complete all as specified and directed by Engineer-in-Charge.
Material & labour for 25mm dia stainless steel pipe curtain rod, powder coated fixed with & including stainless steel hooks/ brackets and decorative finials (at both side), curtain rings (minimum 5 Nos rings per running mtr of curtain rod) shade as approved by GE complete all as specified includng fixing of long size rawl plugs in wall for MS hook including taking out the existing old pelmet box along with old curtain rods complete all as specified and directed.
M&L mild steel work in framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde E-165.
Mild Steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging conforming to Fe-290 (Gde E-165), also fastening and fixing complete all as as specified and directed by Engineer-in-Charge.
Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, Fe-410-W (Gde E-250) complete all as as specified and directed by Engineer-in-Charge.
S&F fot tank base angle, Joist, channel, or tee sections, fixed independently by means of welding, without connecting plates, etc. confirming Fe 410-W(Gde-E-250) quality B complete all as specified and directed.
Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates "grills" etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed by Engineer-in-Charge.
Pre-painted galvalume aluminum zinc coating profile sheet GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified
Pre- painted galvalume aluminum zinc coating profile sheet GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping s crews as complete all as specified and directed.
S&F 18/19 mm thick HDHMR Both side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in cupboards and other accesories etc as in repairs complete all as specified and as directed.
PVC hollow wall panelling 5mm thick any colour/design approved by engr-in-charge, inclusive of fixing on to wall incl moulding end caps fixed with PVC sleeves and screws as required at site including dismantling of walls and ceiling boards/wall paneling or insulation board any thickness, including cover fillets complete all as specified and directed
Providing & fixing false ceiling at all heights with With Semi perforated 12mm thick micro tegular edged GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 4 76 (part 4 )-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 15 x 32 mm of length 3000mm,cross-T of size 15x 32mm of length 1200mm and secondary intermediate cross-T of size 15 x 32 mm of length 600mm to form grid module ofs1ze 600x 600mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50mm long, 8mm outer diameter M-6 dash fasteners, 6mm dia fully threaded hanger rod upto 1000mm length and Lshape level adjuster of size 85x25x2mm .Galvanised iron perimeter wall angle of size 24x 24x0.40mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.
S&F in repair for Vitreous China wash down water closet pan ( pedestal pattern) white ( excluding flushing cistern and flush pipe) including plastic water closet seat cover white, closed pattern with flat botton and cover and mild steel chromium plated or aluminized hinging device incl P or S trap with connection complete all as specified and directed.
S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with PVC `P’ or `S’ trap, integral foot rest including connection to trap and flushing pipe, flushing cistern etc complete and bedding in PCC 1:7:12 type F-2 complete all as specified and directed. Note:- Flush pipe and flushing cistern to be measured and paid separately.
S&F for vitreous china white wash basin with flat back of size 550mmx400mm coloured including MS brackets, cutting for and pinning in ends of brackets, including bottle trap/ PVC waste pipe as in repairs complete all as specified and as directed.
S&F in repair vitreous china Urinal, Half stall type, white (excluding flushing cistern) including providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screw, pointing around urinal back in cement, grating and union for discharge pipe incl brass cp waste coupling, waste pipe, brass cp urinal spreader complete all as specified and directed.
S&F in repair 10 ltr capacity PVC valveless, syphonic action flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, 32 mm dia flush pipe complete all as specified and directed by Engineer-in-Charge.
S&F for 15 mm bore for centre hole basin mixer with spout, fancy type, chromium plated Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixedas in repair complete all as specified and as directed.
S&F 15 mm bore fancy type Pillar taps, cast copper alloy, with capstan heads,chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed to 15 mm bore iron pipe as in repair complete all as specified and as directed.
Supplying and fixing in repairs 15 mm fancy type chromium plated fancy type bib tap brass long body with flange screwed down high pressure CP cast copper alloy with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union complete all as specified and directed by Engineer-in-Charge.
Supplying and fixing in repairs stop/angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated complete all as specified and directed by Engineer-in-Charge.
Supplying and fixing in repairs stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, all as specified, of 15mm bore, fancy type, chromium plated with long shank and cup (Concealed type) complete all as specified and directed by Engineer-in-Charge.
Supply & fix in repairs chromium plated, Brass, Jet spray including flexible pipe 15mm bore, screwed down, high-pressure pipe of 15 mm bore with wall flange fixed to wash down water closet (pedestal pattern) complete all as specified and directed.
S&F in repair Health faucet chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified as directed
S&F Brass chromium plated shower rose 150mm square in shape with 450 mm long arm fixed in repair complete all as specified and as directed.
S&F in repairs toilet papper holder chromium plated with fixing to wall complete all as specified and directed.
S&F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long all as complete.
S&F Bib tap standard of PTMT with flange Minimum weight 15mm-5gms any colour high pressure screwed for iron pipe and fixed .(Minimum weight 15mm-90gms fixed in repair incl PTMT extension Nipple (Minimum weight 15mm-18 gms) fixed in repair complete all as specified.
S&F in repair waste pipe 32mm dia, 800mm long complete all as specified & directed
S&F in repairs steel grating 100mm dia complete all as specified and directed.
S&F for CP Soap dish, approximate size 160x90mm fixed in repair complete all as specified and as directed.
S&F for PVC connections with PTMT nuts of length 600 mm long fixed to 15 mm bore iron pipe or union as in repair complete all as specified and as directed.
110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall set in cement mortar with and including MS clamps made out of flat iron of size 25mm x 3mm including nuts bolts etc complete all as specified and directed.
110 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches complete all as specified and directed by Engineer-in-Charge.
75 mm bore, PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches complete all as specified and directed by Engineer-in-Charge.
PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75 mm bore fixed in repair including jointing to waste pipe in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engineer in Charge.
PVC(SWR) bends (any radius), for 110mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.
PVC(SWR) bends (any radius), for 75 mm bore pipes, with access doors, complete all as specified and directed by Engineer-in-Charge.
S&F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.
S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.
PVC (SWR) trap ‘P or S trap’ including jointing with solvent cement 100 mm bore fixed in repair complete all as specified and directed by Engineer in Charge.
S&F tubes 15 mm, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including clamps and screws fixed on rawal plugs complete all as specified and directed by Engineer-in-Charge.
S&F tubes 20 mm, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including clamps and screws fixed on rawal plugs complete all as specified and directed by Engineer-in-Charge.
Re-fixing only tubes, any grade, to walls and ceilings or laying in floors 15 mm, `medium grade' galvanised, with all fitting and fixed clamps and screws fixed on rawal plugs complete all as specified and directed by Engineer-in-Charge.
Re-fixing only tubes, any grade, to walls and ceilings or laying in floors 20 mm, `medium grade' galvanised, with all fitting and fixed clamps and screws fixed on rawal plugs complete all as specified and directed by Engineer-in-Charge.
M&L for excavating in post holes (or similar holes) each n exc 0.5cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified.
Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and as directed.
Supply only chain link MS galvanized fencing of wire and any size of mesh size (pitch of wire) as directed by Engr-in-charge complete all as specified and as directed.
S&F mild steel round bars as in tie bars with screwed ends, nuts, washers and mild steel plates etc. conforming to Fe Fe 290, Gde E-165 complete all as specified and as directed.
S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but not exc 10 cm long with dia of shank 11 to 15 mm etc complete all as specified and as directed.
M&L for angle iron fencing posts and struts cut indepently and embedding in concrete including cutting tops to shape as directed and drilling holes,notching for wire, etc.inluding flat iron (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.,and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.
S&F galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc.(each line wire to be measured) including taking down old barbed of any and dia complete all as specified and directed.
Manufacturing, supplying and fixing Retroreflective regulatory sign board of size 900 mm dia meter made out of 2 mm thick aluminium sheet, face to be fully covered with high intensity encapsulated lens type retro -reflective sheeting as approved by Engineer-in-charge . Letter, symbols, borders etc. will be as per IRC - 67 with required colour scheme on the boards and with the high intensity grade A. The aluminium sheet to be riveted to M.S. frame of angle iron of size 40x40x4 mm. The boards will be fixed to 1 No. 50x50 mm square post made of M.S. angle 50x50x4 mm, 4 m long welded to the frame with adequate anti-theft arrangement .Sheet work to be painted with two or more coats of synthetic enamel paint over an under coat (primer) and back side of aluminium sheet to be painted with two or more coats of epoxy paint including appropriate priming coat complete in all respects as per direction of Engineer-in-charge.
Note: For the purpose of arriving at lumpsum amount, the amount of credit schedule i.e Sch 'A' section II (i.e Rs 68,479.00 shall be deducted from the total amount arrived.
Total of Schedule 'A' Rs.
M/s REEDIT CONSTRUCTION (BID ID -3495231)
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.38 MB
52Tender.pdf
Tender Documents • 2.48 MB
BOQ_828375.xls
BOQ • 0.58 MB
Download all tender documents and submit your bid