CERTAIN REPAIR TO OTM ACCN OF 15 IDSR, DIV PRO UNIT, FS SECTION ,WCLU, 459 INT AND 13 ELINT SUB GP IN THE AREA OF AGE BR-I UNDER GARRISON ENGINEER AMRITSAR CANTT

Amount

Demolition of brickwork, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed by Engineer-in-Charge.

Material and Labour for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, built in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

All as per Srl item No 2 above but except bricks (old dismantled serviceable bricks obtained from Srl item No 1 shall be reused after necessary cleaning of mortar) complete all as specified and directed by Engineer-in-Charge.

Material and Labour for brick work with sub class "B" bricks (old size) straight or curved on plan exc 6 m mean radius, in half brick thick walls and built in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster of any description on brick walls, etc including raking out joints, hacking for key scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Material and Labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces on walls in CM 1:6 finishing even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material and Labour for rendering 15 mm thick on fair faces of brick work or concrete surfaces on walls in CM 1:4 finishing even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material and Labour for rendering 10 mm thick on fair faces of brick work or concrete surfaces on ceiling in CM 1:3 finishing even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

Material and Labour for applying two coats of whitewash on wall including preperation of newly plastered/old decorated surfaces complete all as specified and directed by Engineer-in-Charge.

Material and Labour for applying two coats of whitewash on ceiling including preperation of newly plastered/old decorated surfaces complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) including preparation of new surfaces complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered surface of wall and Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work complete all as specified.

Taking down Chowkats or frames from the opening of size not exceeding 1.5 sqm each with shutters ( without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

Taking down Chowkats or frames from the opening of size of opening exceeding 1.5 Sqmtr but not exceeding 4 Sqmtr with shutters ( without taking off shutters from the frames) complete all as specified and directed by Engineer-in-Charge.

Taking down Shutters of any description of size not exc 1sqm each complete all as specified.

Taking down Shutters of any description of size exceeding 1 sqm and not exceeding 2 sqm each complete all as specified and directed by Engineer-in-Charge.

Taking down Shutters of any description of size exceeding 2 sqm each complete all as specified and directed by Engineer-in-Charge.

Material and labour for Box type steel window, ERW hollow P-Section size 60 mm x 25 mm, double rebated ERW section of 1.25mm thick, comprising of glazed skelton & gauzed shutter of ERW tube P-Section size 50mm x 20mm with one No openable leaf for each shutter consisting of two Nos Sashbar of T-section 20 x 3 mm welded to frame with one No verticle mullion of ERW box type T Section of size 60mm x 25mm and FI 2mm thick welded/screwed to frame for fixing of glass including fittings and fixture like as Handle, Tower Bolt, Stopper, Cleat, Pintal hinges, holdfast and guard bars etc as given below all as shown on drg No CEJZ/TD-1020/08 SH 1/3 to 3/3 dated 01 may 2008 complete all as specified and directed by Engineer-in-Charge. as follows:- (a) Hold fast 150mm long of MS flat 12mm x 3mm - 4 Nos per Window (b) Handle of Z section 20mm x 25mm, 100mm long- 01 No per leaf (c) MS tower bolt 150mm long - 02 Nos per leaf (d) Z Section stopper 20mm x 25mm, 100mm long - 01 No per leaf (e) Cleat 55mm long of hollow square 15mm, 0.63mm thick- 01 Nos per leaf (f) MS pintol hinges size 75mmx12mm - 2 Nos per leaf (g) MS guard bar 10mm square bars @ 10cm c/c fixed horizontly (h) 3mm thick clear glass sheet 3 Nos per leaf glazing with oil putty (i) Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples in each leaf Note :- Including taking down old steel / wooden window including hold fast PCC 1:2:4 type B0 (four No’s for Each window) & around required plaster in CM 1:4 and match with existing finish complete all as specified and directed by Engineer-in-Charge. by Engineer-in-charge. Painting shall be measured and paid separately.

Material and labour for Box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame ( single rebated), comprises glazed shutter, frame of ERW tube and FI 2mm thick welded/screwed to frame for fixing of sheet glass including fixture and fittings like as Stopper, Cleat, Pintal hinges, holdfast etc all as shown on drg No CEJZ/TD-1019/08 dt 01.05.08 incuding cutting holes complete all as specified and directed by Engineer-in-Charge. as follows. (a) 3mm thick pin headed type glass sheet glazing with oil putty and Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staplesof appropriate size. Note:- Including taking down old steel / wooden window including hold fast PCC 1:2:4 type B0 (four No’s for Each window) & around required plaster in CM 1:4 and match with existing finish complete all as specified and directed by Engineer-in-Charge. by Engineer-in-charge. Painting shall be measured and paid separately.

Supply and Fixing for pressed steel frames 1.25mm thick for door size of frame 125 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges complete all as specified and directed by Engineer-in-Charge.

Material and Labour for PCC 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) in bed blocks for hold fast & similar work etc complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing IInd class hard wood Glazed and skeleton shutters 35mm thick divided into square, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, Section 8 clause 8.24 (a) ; supplied and fitted to chowkats complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs Helical door spring 300mm, ordinary rat tail rod pattern springs, including roller and roller plate fixed to iron chowkats with weilding complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing factory made 30 mm thick flush shutters solid core construction with block board core and plywood face panels.

Material and Labour for two coats of synthetic enamel painting on wooden surfaces of any description over 10 cm in width or girth not otherwise described above pink primer including prepration of previously untreated surfaces.

Supply and Fixing 300mm long Aluminium alloy, Anodised, sliding door bolt with hasp, staple ( bolt type) and fixing clips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed and directed by Engineer-in-Charge.

Supply and Fixing Aluminium, anodised, barrel tower bolts 150mm of extruded section and fixed and directed by Engineer-in-Charge.

Supply and Fixing 150mm long Aluminium handles, cast type anodised and directed by Engineer-in-Charge.

Supply and Fixing stainless steel butt Hinges, 100mm size, medium weight, cold rolled mild steel complete all as specified and directed by Engineer-in-Charge.

Hacking out old broken glass from wooden/ steel window cleaning the surface and removing from the site, thenafter Supply and Fixing clear glass, 3mm thick ordinary quality, in any shape, not exceeding 0.50 sqm in each pane including and glazing with oil putty/wooden beading as per site requiremnets and directed by Engineer-in-Charge.

Supply and Fixing clear glass, 3mm thick ordinary quality, in any shape, not exceeding 0.50 sqm in each pane including and glazing with oil putty and directed by Engineer-in-Charge.

Supply and Fixing Solid PVC Door Frame of Size 50mm x 47mm made out of 5mm plain colour PVC Sheet reinforced with MS Square tube in opening as per specification and frawing and directed by Engineer-in-Charge.

Supply and Fixing 28 to 30 mm thick factory made solid PVC moulded Door shutter with 2,3 or6 raised psnel design with 2mm thick moulded PVC Sheet on the front face and 2mm plain colour PVC Sheet on back face, fixing in frame at site as per specification and drawing and directed by Engineer-in-Charge.

Supply and Fixing powder coated aluminium frame for doors ,windows, ventilators, partition with one or more rebates including joining cleats, rubber neoprene packing for fixing complete all as specified and directed by Engineer-in-Charge. by Engineer-In-Charge.( Min. thickness of powder coating 50 micron)

Supply and Fixing powder coated aluminium glazed shutter(for doors) Al-section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading. ( Min. thickness of powder coating 50 micron) and directed by Engineer-in-Charge.

Supply and Fixing Aluminium powder coated (of any colour) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified .(Min. thickness of powder coating 50 micron)

Taking down aluminium door shutters of area exc 1 sqm but n.exc 2 sqm each and replacement of necessary jointing cleats glazing clips, rubber packing, anodised aluminium snap beading screws etc and refixing in the same opening complete all as specified and directed by Engineer-in-Charge.

Taking down aluminium door shutters of area not exc 1 sqm each window shutters and replacement of necessary jointing cleats glazing clips, rubber packing, anodised aluminium snap beading screws etc and refixing in the same opening complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Sheet glass, 5.5mm thick ordinary quality, in squares,exceeding 0.50 sqm in each pane including rubber packing and aluminium beading with and incl solar control film 25 Micron reflective type sticked to glass panes as per instructions of manufacturer scomplete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs door closer hydraulically regulated, (Alminium die cast body) designation No. 3, universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 Kg and fixed

Supply and Fixing Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed make-Godrej

Supply and Fixing Floor door stopper of aluminium alloy body and tongue anodised with hard drawn steel spring fixed to door shutter of size 150mm.

Supply and Fixing Brass mortice lock, 4 levers, verticle type, size 100 mm, complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Brass mortice lock, 2 levers, verticle type, size 100 mm, complete all as specified and directed by Engineer-in-Charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed by Engineer-in-Charge.

Dismantling Asbestos cement ( corrugated, semicorrugated ,etc.) sheets in roof/wall coverings complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 2mm thick Fibre glass reinforced translucent corrugated/plain sheeting with side lap fixed with coach screw and washer in roof, wall etc and directed by Engineer-in-Charge.

Supply and Fixing framed work as door, chowkhats, and Grill gates of angle frame work fixed with Nut & bolt to wall or other section complete drilling or fixing welding be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings and hanging also festering and fixing complete.

Supply and Fixing Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240.

Material and Labour two coats of synthetic enamel painting on steel surfaces of any description over 10 cm in width or girth not otherwise described above priming coat of red oxide including prepration of previously untreated surfaces and directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish off the premises and directed by Engineer-in-Charge.

Supply and Fixing non skid ceramic light coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or colour cement to match the colour of tiles over and including 15mm thick screed bed in CM 1:6 & complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing glazed ceramic coloured designer tiles 450x300mmx6/7mm thick, etc. on vertical surfaces such as skirting , dados and risers to steps etc. set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match over and including 10mm thick rendering plaster in CM 1:4 on brick surface complete all as specified and directed by Engineer-in-Charge. Note: Colour and design of tiles as per approval of Engineer-in-charge.

Material and Labour for Vitrified ceramic light shade tiles 10mm thick (Square/ rectangular) polished, area of each tiles n.exc 0.36 sqm in floors and skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of cement mortar(1:6) 15mm thick for laying floor finishes complete all as specified and directed by Engineer-in-Charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc.Laid, bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge.

Material and Labour for Machine cut Kota stone slab flooring 20-25 mm thick (size not less than 0.5 sqm each) over cement screed base of 15mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

All as per srl Item No 57 here-in-before but as skirting/dado over rendering 10mm thick in CM 1:4.

Material and Labour Granite (of any type) work (table rubbed and polished) 20mm thick in steps , jambs, pillars, window cills, cooking plateforms and like in cemnet mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in CM 1:4.

Supply and Fixing in repairs vitreous China Squatting pan 'Orrisa' pattren size 580x440mm white with integral foot rest and PVC(SWR) 'P' trap 110/110mm bore complete. Note:-Rate of supply for Flushing cistern, flush pipe, seat cover etc have been taken separately.

Supply and Fixing of Vitreous china wash down water closet pan( pedestal pattern), white with PVC(SWR) 'P' trap 110/110mm bore complete all as specified and directed by Engineer-in-Charge. Note:-Rate of supply for Flushing cistern, flush pipe, seat cover etc have been taken separately.

Supply only 10 Ltr capacity PVC valveless symphonic action type flushing cistern white low level with ball valve flote handle including bracket and flush pipe of polythylene of low or high density or PVC,32mm dia complete all as specified and directed by Engineer-in-Charge.

Supply only Plastic water closet seat,white/ivory,closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device (Toilet Seat Cover) Make-Prayag/Shakti

Supply and Fixing in repairs PVC Jet spray suitable for EWC. Make-Prayag/Polytuf

Supply and fixing Chromium plated Health faucet in repairs with 1.5 metre long chain.

Supply and Fixing in repairs vitreous China wash basin white,flat back size550x400mm including PTMT waste coupling 32mm bore,waste PVC pipe complete, CP brass Pillar Tap 15mm bore of fancy type complete.

Supply and Fixing in repairs glass shelve assembly 60cm in oval shape consisting 5.5mm to 8mm thick glass including CP guard railing with double rail.

Supply and Fixing Sheet glass corner shelf assembly consisting of 5.5mm thick sheet glass corner shelf with chromium plated bracket guard and railing.

Supply and Fixing PVC connection 15mm size with PTMT nuts of length 600mm.

Supply & Fixing vitreous china urinal half stall type with CP spreader white incl CP waste coupling with grating and union fordischarge pipe, including providing and fixing plug, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement fixing with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing Vitrous china urinal partition white of size 310x770mm and fixed to wall terminating about 40cm above floor line complete al as specified and directed.

Supply and Fixing in repairs15mm bore Concealed type stop cock cast copper alloy CP screwed down high pressure with crutch or butterfly handle complete.

Supply and Fixing in repairs15mm bore type angle cock cast copper alloy CP screwed down high pressure with crutch or butterfly handle complete.

Supply and Fixing in repairs of brass cromium brass plated fancy type bib taps 15 mm bore long nose screwed down screwed for iron pipe or for brass complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs Pillar taps 15mm bore, cast copper alloy , with capstan heads, chromium plated , screwed down high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe and fixed.

Supply and Fixing in repairs PVC waste pipe32mm dia fixed to WHB/Urinals.

Supply and Fixing in repairs 100mm dia CP grating with or without hole type complete all specified and directed.

Supply and Fixing in repairs CP brass towel rail of 20mm dia and 600mm long complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs 125mm CP shower rose fancy type with CP arm complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing CP (Box type) toilet paper holder fixed to walls with chromium plated (CP) brass screws complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing 15mm bore tubes (medium grade) galvanised with all fittings and fixed to walls and ceiling or laid in floors complete including taking down all as specified and directed.

Supply and Fixing 20mm bore tubes (medium grade) galvanised with all fittings and fixed to walls and ceiling or laid in floors complete including taking down all as specified and directed.

Dismantling Brick tiles or terracing tiles, single layer on roofs ; Complete all as specified and as directed by Engineer-in-Charge.

Demolition mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in padding concrete fair finish, roof kerbs or mud stops, rounded or chamfered on edges and like including weathering slight rounded and throating ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm including cleaning surfaces etc ; Complete all as specified and as directed by Engineer-in-Charge.

Supply and Fixing (minimum) 3mm thick APP film based poly meric membrance minimum weighing 3Kg per Sqm reinforced with polyester non wove fabric (weight not less than 150 gms/sqm) land on primed surface by forced application over entire roof area with over lapping 100mm to either sides and sealed in after cleaning down the roof by brooms ; Complete all as specified and as directed by Engineer-in-Charge.

Material and Labour for 40mm thick brick tiles, laid on and including 15 mm thick cement mortar 1:6 and joints grouted and pointed flush in CM 1:3 mixed with 5% crude oil by weight of cement ; Complete all as specified and as directed by Engineer-in-Charge.

All as per Srl Item No. 91 here-in-before but except brick tiles. Note:-Old serviceable tiles shall be reused complete all as specified and directed by Engineer-in-Charge.

Disconnecting existing tanks 1000ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified and directed by Engineer-in-Charge.

Disconnecting existing tanks 500ltr capacity, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc complete all as specified and directed by Engineer-in-Charge.

Dismantling water tanks and Supply & Fixing rotational moulded polythene water storage tanks of 1000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-1 including Ball valves high pressure PTMT with epoxy coated Aluminium rod & High density plastic ball screwed for iron pipe and fixed to GI pipe of 20mm bore complete all as specified and directed by Engineer-in-Charge.

Dismantling water tanks and Supply & Fixing rotational moulded polythene water storage tanks of 500 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-1 including Ball valves high pressure PTMT with epoxy coated Aluminium rod & High density plastic ball screwed for iron pipe and fixed to GI pipe of 20mm bore.

Dismantling boarding , any description , fixed in any position with screws.

Material and Labour Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

Providing and fixing 8mm thick Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish and apply a coat of distemper as required (Frame work for ceiling shall be measured and paid separately)complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in reapair 25mm dia stainless steel Curtain rods/ rails, with brackets, stops, rollers, finials, 1 pair of decorative knobs for each curtain rod etc.

Dismantling water tanks and Supply & Fixing rotational moulded polythene water storage tanks of 1000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-1 including Ball valves high pressure PTMT with epoxy coated Aluminium rod & High density plastic ball screwed for iron pipe and fixed to GI pipe of 20mm bore complete all as specified and directed by Engineer-in-Charge.

Dismantling water tanks and Supply & Fixing rotational moulded polythene water storage tanks of 500 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-1 including Ball valves high pressure PTMT with epoxy coated Aluminium rod & High density plastic ball screwed for iron pipe and fixed to GI pipe of 20mm bore.

Supply and Fixing in repairs PVC (SWR) pipe 75mm dia fixed in wall/floor complete all as specified and directed by Engineer-in-Charge.

PVC (SWR) pipes single110mm socketed, in any length with rubber ring joints, laid in trenches or in floors/wal complete all as specified and directed by Engineer-in-Charge. .

Supply and Fixing in repairs 75mm PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge.

Supply and Fixing in repairs 110mm PVC (SWR) bends any radius complete all as specified and directed by Engineer-in-Charge.

Bharatbuilder

GEE EMM ASSOCIATES

Sai Construction Co.

Munish Kalia