GYM AND FLOORING TILES APPLYING WORK IN A.W.H.O COLONY PARK AMBABADI WARD N0 10

Amount

LEG PRESS : Area :- 0.40x1.77 Mtr Safe Area :- Providing and fixing the center p The bottom support thickness is welded the remaining outer frame pipe. the foundation used for Ǿ 80mm made from "C" c & 10 mm thickness, 25mmx25mm. to join the c 3mm thicness is used. the seats are size 330mmx3mm and size 250mmx 200mm. the footrests is made 130mmx311.77 mtr.-1x2.38mtr. fixing leg press made from "B" class G.I. p pipe is of Ǿ 115mm made from "C" class G.I. of M.S. round plate of Ǿ 250mm & at bottom. is of Ǿ 40mm made from "C" class G.I. foundation fixing is consist of three equal class G.I. pipe, M.S. round p x 3mm M.S. angle. centre pipe & outer frame seamless pipe of thickness fitted on the outer frame is made up of FRP material of 300mm of thickness 3mm & M.S. plate of is used to support it. from aluminum casting material, i 10mm & 5mm thickness. pipe, made pipe and 250mm, 10mm items i.e. plate of Ǿ 250mm angle. Ǿ 120mm & thickness 5 support its sizes are the frame of footrests consists of Ǿ 32mm made from "C" class G.I. pipe. closing caps made from top quality FRP material which is of 2 mm thickness. the inner bushes is made from seamless pipe, its diameter is 60mm & 5mm thickness. the pins used in are made up of Ǿ 25 mm hardened bright bar, the bearings used are of "6205zz" permanent lubricated sealed bearing of reputed make (FAG/SKF). the handles used are of rubber grip. high tensile steel with galvanized nut bolts are used for assembly. the serclips used for assembly are of Ǿ 25 mm. the powder coat is done by poly urethane & exoxy powder with 60 to 70 micron thickness.

SIT UP BOARD : Dimensions : - 1820 mm (Length) x 430 mm (Width) x 580 mm (Height). Safe Area : - 2.8 Mtr x 0.6 Mtr. Sit up Board equipment made from "B" class G.I. pipe of different NB. NB stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. The main frame is of 50 mm NB made from "B" class G.I. pipe supported with the M.S. round plate of Ǿ 250x10 mm thickness. Fibre reinforced plastic sheet of 3 mm thickness is bounded on 25 mm NB (G.I.) "B" class pipe of main frame. The base support of the sit up board is made 40 NB (G.I.) "B" class pipe. The foundation used for fixing is structure and made from center pipe of G.I. of 80 NB "B" class welded with M.S. round plate of Ǿ 250 mm & 10 mm thick main pipe. Supported with 25 mm x 25 mm M.S. angles of 3 mm thickness and 20 mm x 40 mm CRC square pipes of 3 mm thickness. The powder coating is done with pure polyester powder Ackzonoble or Berger paints with 60 to 70 micron thickness.

ROWER : Area :- 1.2 x 1 Mtr Safe Area :- 1.5 x 1.5 Mtr Providing and fixing rower made from "B" class G.I. pipe. the main frame is of 80mmx40mm & 40mmx40mm CRC pipe with 2 mm thickness. the handle frame is of Ǿ 32 made from "C" class G.I.pipe. the foundation used for fixing consists of three equal items i.e. Ǿ 40mm made from "C" class G.I.pipe, c channel of 75mmx40mmx5mm & 25mmx25mmx3mm M.S. angle. to join the movement frame to main frame seamless pipe of Ǿ 50mm & 3mm thickness is used. the seats which are fitted on the main frame is made up of high quality FRP material of size 330mmx300mm of thickness 3 mm & M.S.plate of size 250mmx200mmx5mm is used to support it. closing caps are made from top quality FRP material which is of 2 mm thickness. the pins used are made up of Ǿ 17 mm hardened bright bar. the bearings used are of "6203zz" permanent lubricated sealed bearing of reputed make (FAG/SKF) the handles used are of rubber grip. high tensile steel with galvanized nut bolts are used for assembly. the bushes (Stopper) used to avoid the collusion. the serclips used for assembly is of Ǿ 17 mm. the powder coat is done by poly urethane & epoxy powder with 60 to 70 micron thickness.

TRIPE HIP TWISTER : MACHINE PARTS DESCRIPTION OF TRIPE HIP TWISTER : 1 Mounting Plate 2 Center Pillar 3 Plastic Cap 4 Circular Handle 5 Connecting Rod 6 Floor Rest Pipe 7 Standing Pad FOUNDATION OF MACHINE IS CEMENTED AND BOLTED WITH BASE CHANNEL AND CIRCULAR MOUNTING PLATE WHICH DIMENSION IS BELOW : 1 Measurement of base channel is 3'x6"x2" 2 Circular mounting plate's diameter 233mm and thickness is 8mm. 4 hole on this plate at 90 degrees which P.C.D. is 170mm. Hole diameter is 20mm. MACHANICAL DIMENSION AND MEASUREMENT OF MACHINE ARE FOLLOWING : 1 A circular mounting plate which diamension is same of above circular mounting plate and it is tightened with nut and bolt. 2 On this circular mounting plate a center pillar is welded. Diameter of center pillar is 114mm and height is 1288mm. 3 Plastic cap is fixed on the top of center pillar and tightened with help of screw. Diameter and height is 120mm and 69mm. 4 Circular handle is welded at the height of 1171mm from the base of circular mounting plate. OD of circular plate is 557 and ID is 493mm. Three pipe rod which diameter 32mm are welded at 120 degree. 5 Connecting rod for floor rest pad which diameter is 48mm. It is being bended after 131mm at angle of 30 degree and bending radius is 124. Bending length is 185mm. Again it is being bended at angle of 30 degree and bending radius 76. Bending length is 71mm. Three pipes of same dimensions are welded at the angle of 120 degree and collinear to 32 diameter's pipe rod of circular handle. 6 Three floor rest pipe which diameter 114mm and height 105mm and welded at linear center with each connecting rod. 7 Three plastic standing pad which diameter is 280mm and height is 36mm and attached with each floor rest with help of ball bearing which OD 60mm. All plastic standing pad and floor rest pipe is connected with shaft which diameter is 28mm. Note : All the movable joints have a PIN BEARING in between, tightened with the Allen bolt polydrive head bolt having plastic cap on the ends. Since plastic caps are fixed on the ends, the bolt can't be opened until they will be broken.

CHEST PRESS CUM SEATED PULLER : Dimensions :- 2000mm (Length)x710mm (Width)x2200mm (Heigth) Safe Area :- 3.0 Mtrx1.7 Mtr. Chest press cum seated puller equipment made up of "B" class G.I. pipe of different NB. NB stands for nominal bore sizes i.e. internal diameter of pipe in millimeters. The center pipe is of 100 NB made up of "B" class G.I. pipe. The bottom welded with support of M.S. round plate of Ǿ 250mm & 10mm thickness. The connecting pipes are made up from 25NB "B" class G.I. pipe. The handle frame is made up from 32NB "B" class G.I. pipe. To build structure bushes are used which are made from seamless pipe of 50mm O.D. and 6mm thickness as well as 50mm diameter solid bar is used. The foundation used for fixing is a structure and made from center pipe of G.I. of 80NB "B" class welded with M.S. round plate of Ǿ 250mm & 10mm thick. Main pipe supported with 25mmx25mm. M.S. angles of 3mm thickness and 20mmx40mm CRC square pipes of 3mm thickness. The seats and back rests are fitted on the outer frames are made up of M.S. sheet of size 330mmx300mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20mm with no sharp edges. Closing caps are made up of injection moulded plastic LLDPE/HDPE. Foundation cover cap is made from injection moulded plastic LLDPE/HDPE. Pins used of diameter 25mm and 17mm are made up from SAE 8620 bright material. The bearing used are of "6205zz" & "6203zz" permanent lubricated sealed bearing of reputed brand. High tensile steel with galvanized nuts & bolts are used for assembly. The cerclips used for locking is made up of A24 & A16 The powder coating done with pure polyester powder from Ackzonoble or berger paints with 60 to 70 micron thickness.

CYCLE : Dimensions :- 1570mm (Length) x 570mm (Width) x 900mm (Height) Safe Area :- 2.5 Mtr x 1.5 Mtr Cycle equipment made from "B" class G.I. pipe of different NB (NB stands for Nominal Bore size i.e. Internal Diameter of pipe in millimeters) The main frame of 50 NB made from "B" class G.I. pipes. M.S. round plate of Ǿ 300mm & 10mm thickness used to form a paddle assembly. The handle frame is of 25 NB made from "B" class G.I. pipe. The seat and back rests are fitted on the outer frames are made up of M.S. sheet of size 330mmx300mmx2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20mm with no sharp edges. The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB "B" class welded with M.S. round plate of Ǿ 250mm & 10mm thick main pipe supported with 25x25mm M.S. angles of 3mm thickness and 20mmx40mm CRC square pipes of 3mm thickness. Closing caps are made up of injection mounlded plastic LLDPE/HDPE. Pins used of Diameter 25mm are made up from SAE 8620 bright material. Pins used of Diameter 13mm are made up from ENB material with CRCA pipe 20x20mm of thickness 3.00mm for paddle assembly. The bearing used are 6001zz & 6205zz permanent lubricated sealed sealed bearing of reputed brand. High tensile steel with galvanized nuts and bolts are used for assembly. The circlip used for assembly are of A24 type. The powder coating done with pure polyester powders from Ackzonoble or berger paints with 60 to 70 micron thickness.