WBPHED/05_01/AE-III/CMD/25-26

Amount

Carrying charges of existing withdrawn 1 no 12.5 HP submersible pumping machinery from said w/s scheme to nearest electrical work shop and back carrying the said pump-motor set from workshop after repairing including loading & unloading charges.

Dismantling the defective pump & motor set part by part for detecting actual fault.

Supply & Delivery of following items for Pump portion

G.M. Bush for Suction portion.

G.M. Bush for delivery portion.

Coupling Bush-shaft (SS)

Bush (Rubber)

Shaft Key

Thrust bearing & thrust plate complete set

Supply & Delivery of following items for Motor portion

Motor Bush for upper & lower (2 Nos).

Rewinding the burnt out 12.5HP motors with supplying of water proof PVC copper wire of suitable gauge and all others relevant materials to complete the job after necessary cleaning the slot as per direction. (Cost of winding is considered after deduction of the value of burnt out coil).

Reassembling the pump & motor set with the above supplied materials as mentioned in above and the old serviceable spares to complete the job as per direction of E. I. C.

Making synthetic enamel painting (two coats) of the above repaired motor & pump set after scraping after using primer.

Supply & delivery of 80mm dia. CIDF single door swing Non Return Valve, PN 1.0 rating (Conforming to IS:5312) (MOC & TC needed for valve).

Supply & Delivery of 150mm x 80mm CIDF Reducer

Supply & Delivery of 150mm dia CIDF short piece -150mm long

Supply & Delivery of 150mm dia CIDF short piece -300mm long

Heavy type suitable dia. MS suspension clamp along with nuts bolts and washers.

CIDF 90°bend- 1no., CI flanged tee- 1no., blank flange-1no., CI/ MS flanged short piece 0.50 mtr.-1no, CI/ MS flanged pipe 1mtr.- 1 no. etc (as per IS specification and certification registered) for construction of delivery pipe line and wash out line.

Heavy type 250mm dia./suitable Split type tube well cover with clamping arrangement including supply of nuts, bolts and washer as per departmental design.

Anti snapping safety device for pump set by supplying suitable size of MS angle busket and nylon rope of required length including supplying of nuts, bolts and all other materials.

Suitable Kiosk box for cable connection of submersible pump motor set with degree of protection IP 65 including suitable legs and 6 Nos. Al. Bus bar for 63 Amps and all necessary earthing arrangement and insulator as per direction of EIC.

Making brick pillar 0.25 x 0.25 x 0.75 Mtr/Suitable hight for supporting of valves and pipes with 12mm thick plaster and net cement finish complete. (Both Pipe line)

Making CC foundation for support of the kiosk box after excavating the earth upto a depth of 0.6 Mtr below the GL including supply of all materials complete with 12 mm thick cement plastering with net cement finishing complete as per direction of EIC (size: 3' x 1' x 5')

Carrying charges of old S.valves, power cable (100mtr) from said site to Patelnagar store including loading & un-loading complete.

Laying of one No. cable (Dept.Supply) up to 35 sq.mm in underground trench 460 mm wide x 760 mm average depth, with brick protection on the top of the cable with 8 (eight) Nos. bricks per metre, including filling the space between the brick & cable and also the trench with shifted soil, leveling up and restoring surface duly rammed.

Installation of Submersible pumping machinery to newly sunk tubewell along with column pipes (as required- with Dept. supplied fitting), top cover, valves, and specials of above with protection pipe and supply of MS clamp, nut bolt, cable gland socket etc. making inerconnection of the pump delivery line to pump collecting main line near tubewell with supply of all necceasary pipe, reducer/enlarger, GI/MS specials etc. including brick, sand, cement, rod etc and laying & drawing of all power cable properly on on wall / tray for layout & IE rules, installation of pump controllers, main switch etc. as required and all to complete the job including all connection, socktings & testing commissioning as per direction of EIC.

Making flange joint to CIDF pipe, specials, valves etc.with supply of necessary nuts and bolts,rubber insertion of 6kg/m2 (3mm gauge) and materials required including dewatering if any tools and plants, labour cost etc. as per specification and direction of EIC (Nut and bolts shall be of TATA/GKW make) for 150mm.dia.

Making flange joint to CIDF pipe, specials, valves etc.with supply of necessary nuts and bolts,rubber insertion of 6kg/m2 (3mm gauge) and materials required including dewatering if any tools and plants, labour cost etc. as per specification and direction of EIC (Nut and bolts shall be of TATA/GKW make) for 80mm.dia.

Supply & Delivery of following, IP65 illuminating streets and other outdoor area withbody material is made from PDC and Toughened Extra Clear Flat Glass for durability, Robust Construction, high power LED, with potted LED Driver to ensure uniform distribution, , Lighting Color Cool White, IK07, lamp colour temperature – 6500K,, surge protection up to 4K (Inbuilt) provision for external up to 10KA. 35W, Philips,BRP 032 LED 60 CW MR PSU GR DX. System Lumen output-6000Lm, Street Light

Fitting & fixing of street light luminaries with necessary erection materials, inter connection, jointing of cables and testing complete upto entire satisfaction of EIC.

Supply and delivery of 50mm dia PVC pipe (Sch-80) (Make- Any make of PHED Approved) for laying of cable from kiosk to pump.

Supply and delivery of 50mm dia PVC pipe 90⁰ elbow (Sch-80) (Make- Any make of PHED Approved) for laying of cable from kiosk to pump.

Labour for fitting and fixing of 50mm dia high density poly-ethylene pipes or P.V.C. pipes for above ground work including cost of jointing materials paints etc. fitting and fixing all necessary specials, cutting pipes, making threads, cutting holes in walls or R.C. floor where necessary and mending good all damages excluding the cost of masonry or concrete work, if necessary, but including the cost and fitting and fixing holder bat clamps(any floor) or for underground work including cutting trenches upto 1.5 metre and refilling the same complete as per direction of the Engineer-in-charge.(Payment will be made on centre line measurement of the total pipeline including specials. )

Painting of pipe line surface with 2nos. of coats of paints with ready mixed paint/primer of approved make and brand incl. preparation of surface by sand paper/emery paper, cleaning etc. for receiving fresh coat of paint

Add: @ 18% GST of Sl. No:1.00 to Sl. No: 36.00

Add: @ 1% Cess of Sl. No:1.00 to Sl. No: 37.00

HINDOL ROY (BID ID -6717097)

Birbhum Electric Works (BID ID -6717120)