Addn Altn to old admin bldg for setting up of security control room and demolition and reconstruction of bldg P 6 Jetty Store Room at NAD under GE Gomantak Vasco

Amount

Schedule 'A' Part I B/R Portion

Taking down chowkats with shutters (without taking off shutters from the frames) area n exc 1.5 Sqm all as specified & directed.

Taking down chowkats with shutters (without taking off shutters from the frames) area exc 1.5 Sqm and n. exc 4.00 Sqm each all as specified & directed.

Dismantling Concrete in Roof slab,beam and similar work provided for cement concrete is reinforced (reinforcement cut as required to facilitate demolition) all as specified and directed by Engr in charge.

Separating, scraping and cleaning of reinforcement (Demolition of concrete measured separately)

Taking up or down 20mm steel tubing and connections fixed to wall / floor

Taking up or down 15mm steel tubing and connections, fixed to wall /floor

Dismantling of water tanks n.exc 250 ltr and removing to store

Demolition of Brick work or stone/boulder masonry, built in Cement mortar including all quoins, arches, pillars, etc, but excluding ashlarfacings, dressed stonework and precast concrete articles all as specified and directed by Engr in charge.

M&L for Pre-cast cement concrete type C1 (1:3;6) block masonry with solid blocks, exc. 10 cm in width and setting in mortar (1:4) complete all as specified and as directed.

Demolition cement concrete (unreinforced) in ground floor and paving n exc 15 cm thickness (below or above ground level

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out hard/dense soil all as specified and as directed.

Excavation in trenches, n.exc. 1.5 m wide and n.exc. 1.5 m in depth, for foundation etc, or manholes etc and getting out in hard soil all as specified and as directed...

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/disintegrated rock all as specified and as directed

M&L for Cement concrete (1:4:8) type D2 as in foundations, filling and mass concrete all as specified and as directed.

M&L for TMT bars 10mm dia & over cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed

Ditto, but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed

Use & waste of Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar complete all as specified and directed

Use & waste of formwork to sides of pilars,posts, struts, piers, columns and stanchions, rough finished surfacdes of concrete all as specified

Formwork to sides and soffits of roof beams, beam haunchings, girders, bressummers, including supports, overhangs, etc. also splays between floors and beams, etc.complete all as specified and directed

Use & waste of Formwork to chajjas, incl edges and similar work; not exceeding 200mm thick (Horizontal or sloping) all as specified and directed

Use & waste of Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) all as specified and directed

M&L for RCC (1:1½:3) using (20mm graded stone aggregate) as in foundations footing, plinth beams, bases for columns and basement slab, under reamed piles and mass concrete complete all as specified.

M&L for RCC(1:1½:3) using (20mm graded stone aggregate) as in columns, pillars, posts & struts complete all as specified.

M&L for RCC (1:1½:3) using (20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified.

M&L for RCC (1:1½:3) using (20mm graded stone aggregate) as in chajjs complete all as specified.

M&L for RCC (1:1½:3) using (20mm graded stone aggregate) as in roof slab supported on walls, beams and columns (Horizontal or sloping) complete all as specified.

M&L Providing pre cast cement concrete type B1 1:2:4 (20 mm graded aggregate) in manhole cover slabs set tin cement mortar 1:6 including necessary form work all as specified and as directed.

M&L for Pre-cast cement concrete type C1 (1:3;6) block masonry with solid blocks, 10 cm in width and setting in mortar (1:4) complete all as specified and as directed.

Returning, filling in , including, spreading, levelling, watering and well ramming in layers not exc 25cm thick soil complete all as specified and directed

Removing excavated materials (soft/dis integrated rockl) to a distance n.exc 50m and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed

M & L Hard core, broken to gauge n exc 63 mm for plinth protection/ under floor as directed by Engr in Charge.

M&L 75 mm thick cement concrete type, C2 1:3:6 using (40 mm graded aggregate) as in plinth protection finish the surface even and smooth all as specified and as directed.

M&L for PCC (1:4:8) type D-2 (using 40mm graded aggregates) as in sub base floor 75mm thick

M&L for Vitrified ceramic tiles light shed 10 mm thick (square/rectangular) polished area of each tiles not exceeding 0.36 sqm but in floors etc set & jointed in neat cement slurry & pointed in white or coloured cement with pigment to match including 15 mm thick screed bed (1:4) CM as specified & directed

Dismantling floor,hearth or wall tiling including cement mortar bedding ( but not backing coat) removing serviceable tiles and rubbish off the premises

M&L Screed bed or bedding layer of mortar 20 mm thick for laying floor finish CM: 1:4 all as specified and as directed.

M&L Non - skid colour Ceramic tiles 7 to 8 mm thick quare/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.16 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 20mm thick screed in CM (1:4) complete all as specified and directed.

M & L rendering cement plaster 10 mm thick with CM 1:4 as backing coat to receive tiles on vertical surfaces all as specified and directed.

M & L Glazed ceramic tiles in vertical surface 350X250X7mm/ 450X350X7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match (coloured tiles)all as specified and directed.

Taking down cement plaster on brick work or stone walls including racking out joints ,hacking for key,scrubing down with water etc

M & L 15 mm thick rendering on fair faces of concrete in CM 1:6 finish the surface even & smooth without using extra cement complete all as specified and directed

M&L rendering cement plaster 1:4 , 15 mm thick on fair faces of brick work or concrete surfaces finshed even and smooth without ung extra cement.

M & L 15 ( 10+5) mm thick rendering in two layer on fair faces of concrete in CM 1:4 finish the surface even & smooth without using extra cement complete all as specified and directed ( NOTE : II nd coat 5mm thick with WPC )

M & L 5 mm thick rendering on on soffit of slab in CM 1:3 finish the surface even & smooth without using extra cement complete all as specified and directed

M & L for rendering in CM 1:3, 10 mm thickness on roof slab finishing the surface even and fair with out using extra cement complete all as specified and directed.

Supply only Liquid water proofing compound.

Material & Labour for preparation of old surfaces of ceiling including scraping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc (Plastered or unplastered surfaces) and applying one coat of white (lime) wash complete all as specified and as directed.

S & F water proofing treatment to the roof slab and chajja using 4mm thick APP modified membrane consisting five layer membrane with features as specified, weighing not less than 4.0 kg/Sqm laid over a coat of cold applied bituminous primer @ 0.2 litre per Sqm on surface provide a layer of APP modified membrane by torching application including sealing the overlap with torching with 150 mm on length side and 100 mm on width side as per manufacturer's instruction including joints and changes in direction be covered with thin cement slurry in CM 1:3 mixed with SBR latex @ 200 ml/bag of cement curved well before laying of membrane all as per manufacturer's instructions and provide a finishing coat with solar reflective bituminous aluminium paint @ 0.10 kg/m2 as prescribed by manufacturer of membrane to the satisfaction of Engineer-in-Charge. Note:- 1. Irrespective of the lap the net covered area will only be measured for payment.

suppling & fixing in opening Solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colourPVC sheet reinforced with M.S. Square tube, suppling & fixing in opening all as specified and as directed.

Supplying & fixing in frame at site Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, as per specification

M&L 2nd class hard wood plain solid straight chowkats and frames wrought framed rebated on the solid rounded or chamfered put together with glue pined joints

M&L 35 mm thick 2nd class HW plain framed pannelled shutter (any number of panels) with panels of timber flat on both sides or of veneered particle board medium density , wood particle board with commercial face veneers , supplied and fitted to chowkats.

M&L for preparation of new untreated wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

S&F 100mm long Stainless steel Butt hinges fixed to door frame.

S&F 150 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed

S&F 150mm long Fancy type Aluminium handles, cast type, anodised

S&F 200mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S & F powder coated (50 micron) Aluminium window or ventilator shutter and frame any type (slidding or openable) with frame or other similar work etc section fabricated by using the JINDAL/ INDAL /HINDALCO /sections including necessary roller,wheel cleat handals locking arrangements also to receive 4.8mm thick glass with aluminum chanel beading and stainless steel scrw including and rubber gasket beading etc complete (the weight of rubber gasket beading will not be measured with the weight of aluminum shuter glass will be measured and paid separately)All scections as approved by GE

S&F 4.8 mm thick Sheet glass, ordinary quality and glazing with oil putty/rubber beading in square/Rectangular n exc 0.5 sq. m in each pane.complete all as specified and directed

S&F Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed

Supply and fixing as in replacement for vitreoues china WHB, white, flat back, of size size 630x450mm including CP brackets, CP waste coupling 32 mm bore, PVC waste pipe 32mm dia with and including 15mm bore PVC connection pipe 450mm long with PTMT nuts at both ends complete all as specified and as directed.

Supply & Fixing in repairs Flush pipe of polyethylene of low or high density or PVC 32 mm dia for low level cistern

S&F vitreous china half stall urinal flat back, size of 465 x 355 x 265mm (minimum) white, with grating and union for discharge pipe including waste pipe of polythelene of low or high density or PVC 32mm dia.

Supply and fixing as in replacement vitreous China wash down water closet pan (pedestal pattern) with ‘P’ or ‘S’ trap, front or back inlet, fixing bolts, with coloured PVC seat cover and making all necessary connections complete as specified and as directed by the Engineer-in-Charge.

S & F for cromium plated health faucet with stand 1.5 mtr flexible lead including two way brass cromium plated angle stop cock 15mm dia complete all as specified and directed (Make Sona or equivalent)

S & F PVC valve less, syphonic action type, flushing cistern, 10 litres, low level, white, with inlet, ball valve, float and handle including brackets and connections to pipes complete all as specified and directed

Supplying and laying of 25 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 20 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 15 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supply & Fixing in repairs Pillar taps, 15mm dia, cast copper alloy, fancy type with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repairs

S&F 15mm dia chromium plated Bib taps , screwed for iron pipe. Complete all as directed

Supply & Fixing concelead CP stop cock/angle cock 15mm dia, fancy type with capston heads screwed both ends for iron pipe or for unions and fixed in repair

Supply & Fixing Swivel shower of C P Brass any colour for fixing with 15mm pipe .(Minimum weight 40gms) fixed in repair.

Supply & Fixing shower arm 15mm size,195mm long with bend of 45degree with flange of CP brass any colour. (Minimum weight 40gms) fixed in repair.

Supply & Fixing PVC connections 15 mm size with PTMT nuts of length 600m fixed in repair.

S&F 500 Ltrs Rotational moulded polyethylene water storage tanks sintex (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed

Supply & Fixing Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I, for 1000 ltrs capacity.

S& F ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed of 20mm bore min weight 455 gm.

S&F in repair 15mm bore stop valve concelled type, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union as fixed complete all as specified and directed.

Supply & Fixing Towel Rail 600mm long of CP brass fixed with and including Chromium plated brass screws and wooden/plastic cleats .(Minimum weight 190gms) fixed in repair

S&F 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and as directed

M&L 100 mm dia floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement all as specified and as directed

Supply and fixing as in replacement 100mm dia grating doom with waste hole of PTMT (minimum weight 25gms) complete all as specified and as directed by the Engr-in-Charge. Make: Prayag / Polytuf

Supply & Fixing Stainless steel soap dish standard size heavy

M & L for three coats of white wash on newly plastered celing surfaces all as specified and as directed.

M&L for preparation of new plastered surface & applying two coats of oil bound distemper (OBD) over a coat of white chalktening on wall complete all as specified and directed by Engineer-in-charge.

M/L for preparation of old decorated surfaces of walls including cornices, pillers etc and applying one coat of oil bound distempere, complete all as directed by Engr -in-charge.

Material & Labour two coats of acrylic emulsion extenior paint (anti fungal painting-APEX or Equivalent) over a coat of acrylic amulsion primer on new surface including preparation of surface of any description all as specified and directed by Engr-in-Charge.

Material & Labour for complete removal of exiting treatment and prepration of old surface and applying two coats of acrylic emulsion extenior paint (anti fungal painting-APEX or Equivalent) over a coat of acrylic emulsion primer of any description all as specified and directed by Engr-in-Charge.

Material and labour for applying two coats of cement base paint after and including complete removal of existing treatment of old plastered surfaces of walls complete all as specified and as directed.

M&L for preparation of old painted surfaces of wood over 10 cm width/girth and applying one coat of synthetic enamel paint all as specified and directed.

Removing building material/debris to a distance of 1.0 Km and spreading in layers all as directed by Engr in charge. Note : 0.62Cum may be consider as one load all as specified and directed by Engr-in-Charge.

Dismantling boarding any description fixed in any position with nails including aluminium snap gride

S&F 605x605mm anodised aluminium snap grid frame work for false ceiling all as specified including hangers 4 mm dia. G.I.wire (upto 1.2m to 2.0 m length) adjusting level fixed to roof with steel members

M&L PVC insulation panel (10mm th) with EPS stuck to 1mm plain PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S. As per specification and drawing

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S & F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or ther covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410 -W (Gde- E- 250) quality- A

Material & Labour for preparation of new steel surfaces and apply two coat of Anti corrossive paint over a coat of anti corresive primer wiith complete removal of existing treatment all as specified and directed

Material & Labour for Cement concrete type B-1,1:2:4 (20mm graded) 25 mm thick PCC as in sub base for floor complete.

M&L for machine cut Kota stone slab of size 600mm x 600m x 18 to 20 mm thick as in flooring , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror finished complete over screed bed of 15mm thick in CM 1:6 all as directed .

M&L for machine cut Kota stone slab of 18 to 20mm thick, in riser of steps, skirting, dado etc. over & including 10mm thick rendering (bedding layer) in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror finished complete.

M&L plain cement concrete in benching (surface channels and drains) type B1 1:2:4 (20 mm graded stone aggregate).all as specified and as directed.

M&L plain cement concrete type B1 1:2:4 (ung 20 mm graded stone aggregate) in coping, incl weathering, slighntly rounded or chamferred angle and throating, as directed.

S&F 150 mm dia PVC (SWR) pipes single socketed in any length with rubber rings joints laid in trenches all as specified and as directed..

M & L concrete bed, type C-2, 1:3:6 for drain pipes including packing under and haunching against the des of pipes after they are laid and tested for150mm pipes all as specified and as directed.

S&F in repair 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to floor

S/F for in repair 110 mm dia PVC (SWR) grade bends of any radius

S & F in repair 110mm dia PVC (SWR) branch piece, single (single Y equal or unequal) complete all as specified and directed.

S&F 110 mm dia PVC (SWR) vent pipes single socketed in any length with rubber rings joints all as specified and as directed..

S & F 110 mm dia PVC (SWR) vent cowl .

S & F only Septic tank hume pipe 10 users capacity exc. in soft dintegrated rock,pcc filling etc including RFR and disposal of surplus spoil complete.

Construction of Soakage well 1.8m dia and 3.0m deep , Excavation in hard soil/ Soft Rock. Foundation with PCC (1:3:6) , Fly ash brick work in CM (1:4), RCC cover slab incl Precast Manhole cover , and filling with brick bats complete all asper CWE (N) Drg NO : AFB/TD/120 Dt: 07/08/99 Sheet NO: ½ & 2/2

Schedule 'A' Part II E/M Portion Demolition

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safecustody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.

Taking down old unserviceable MCB DB

Taking down old unserviceable LT UG Cable 1100 Volts grade

Taking down old unserviceable pipeline

Schedule 'A' Part II E/M Portion Internal Electric Supply

M&L for one light point or fan point controlled by one switch with cables 1.5 Sqmm copper cable FRLS multistranded unsheathed drawn through & including concealed PVC conduit and 1.5 sqmm conductor cable for earth wire including making connection with common earth and earth dolly including pressed steel terminal al boxes concealed in wall with 3 mm thick plastic laminated sheet top cover fixed with brass screw for mounting switches sockets regulator etc all as per directed by Engr-in-Charge.

M&L for point wiring for 5 amp independant point with 1.5 sqmm copper wire & 1.5 sq mm copper wire as earth lead drawn through & including concealed PVC conduit of suitable size.

All as per item No 2 but 2/3 pin socket out let 5 Amps with 1.5 Sqmm on same board.

M&L for point wiring for 15 amp independant point with 4 Sqmm copper wire & 4 Sqmm copper wire as earth lead drawn through & including concealed PVC conduit of suitable size.

Supply & fixing switch piano flush button single pole one way 5 Amps all as specified and directed.

Supply & fixing switch socket combination outlet 2 in 1 5 pin 5 Amps flush type all as specified and directed.

Supply & fixing switch socket combination 2 in 1, 6 pin 15 Amps flush type all as specified and directed.

Supply & Fixing modular switch 1 way 6A, 1 module, 230 volts.

Supply & Fixing modular switch one way 16 Amps, 1 module, 230 volts.

Supply & Fixing modular socket 6 Amps-2/3 pin combined, 2 module.

Supply & Fixing modular socket 6A/16A-2/3 pin combined, 2 module.

Supply & fixing modular metal flush box 3 module.

Supply & fixing modular metal flush box 8 module.

Supply & fixing modular metal flush box 12 module.

Supply & fixing modular white cover plate with frame, 3 module

Supply & fixing modular white cover plate with frame, 8 module

Supply & fixing modular white cover plate with frame, 12 module

Supply & Fixing ceiling rose, surface Bakelite 65x50 mm Two to three terminals

Supply & Fixing stepped type 2 module modular electronic fan regulator flush type including removal of old one.

Supply & Fix in repair MCB 6 to 32 Amps, Single Pole, braking capacity 10KA, B curve (ISI Marked).

Supply & Fix in repair MCB 32 Amps, SPN, braking capacity 10KA, C series complete all as specified and directed.

Supply & Fixing sheet metal enclosure DB, 8 way, SPN, double door factory made powder coated including neutral/earth connector, fixed in wall complete all as per specified and directed by Engr-in-Charge.

Supply & Fixing MCB protected socket of 20 Amps with sheet metal enclosure including plug top of 25 Amps complete with one single pole 240V with 20 Amps MCB including disconnecting and removal of old one. Make : Havells Cat Part No. DHDMCSN0251020 or equivalent in Legrand/C&S/Anchor

Supply and Fixing LED tube light fitting surface mounted integrated type with 20 watts LED having minimum 100 lumens/watt complete including dismantling old fittings all as specified and directed.

Supply and Fixing LED tube light fitting surface mounted integrated type with 10 watts LED having minimum 100 lumens/watt complete including dismantling old fittings all as specified and directed.

Supply and Fixing LED light fitting Recess/Surface mounting LED flat panel 2'x2' with high efficient LEDs & glare free opal diffuser of 34 watts LED including dismantling old fittings all as specified and directed.

Supply & Fixing Submain wiring with 2.5 sqmm three runs of single core multi stranded FRLS unsheathed PVC copper conductor cable 1100 Volts as per colour code drawn in through concealed PVC conduit including all accessories as required and connecting to Existing main switch board/DB & testing on completion including dismantling old unserviceable submain wiring complete.

Supply & Fixing submain wiring with 2 Runs of 4 Sqmm, PVC insulated, unsheathed, single core, multi stranded, 1100 volts, FRLS copper conductor cable drawn in and including 25/32mm wide PVC conduit concealed with all accessories as required along with 1 run of 4 sqmm PVC insulated, unsheathed, single core, multi stranded copper conductor cable as continuous earth wire and connecting to existing main switch board/Distribution Board and testing on completion all as directed by Engineer-in-Charge.

Supply & Fixing step type electronic fan regulator flush type on existing phenolic laminated sheet for 48" / 56" sweep ceiling fan complete.

Supply & fixing exhaust fan 300mm sweep, heavy duty, 230 volts including dismantling of old one depositing in MES store yard as per specified and directed by Engr-in-Charge. Make : Usha/Havells/Bajaj

Supply & fixing ceiling fan 1200mm sweep, 5 star rated (ISI Marked), 230 volts includung connection rod as per existing size of length of GI pipe medium grade including dismantling of old one and depositing in MES store yard as per specified and directed by Engr-in-Charge. Make : Usha/Havells/Bajaj

Supply & fixing brushless direct current (BLDC) ceiling fan 1200mm sweep (ISI Marked), 230 volts, 26 Watt includung connection rod as per existing size of length of GI pipe medium grade including dismantling of old one and depositing in MES store yard as per specified and directed by Engr-in-Charge. Make : Orient/Havells/Bajaj

Schedule 'A' Part II E/M Portion External Electric Supply

Supply & Fix under ground cable XLPE insulated armoured heavy duty 1100 volts grade conforming to IS 7098 Part-1 1988 with aluminium conductor multistandarded including centre gland, lugs,jointing materials etc laid in trenches or fixed it to wall including dismentling of existing cable of 50 Sqmm 3.5 core.

Excavation in trenches not exceeding 1.5 m width and not exc 1.5m in depth getting out in hard/dense soil

Excavation in trenches not exceeding 1.5 m width and not exc 1.5m in depth getting out in soft disintegrated rock

M/L for sand cushion in trenches for cable protection complete all as directed and specified.

Supply and lay PCC cable cover class LV type 1 flat size 250mmx150mmx40mm.

M&L for Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm in thick using excavated hard/dense soil.

M&L for Removal of surplus soil to a distance not exceeding 50 m and depositing where directed by Engr-in-charge.

Supply and laying of High density poly-ethylene pipes (HDPE) 40 mm dia, pressure rating 6 kgf/sqcm laid in trenches as per direction of Engr-in-Charge.

Schedule 'A' Part II E/M Portion External Water Supply

Excavation in trenches not exceeding 1.5 m width and not exc 1.5m in depth getting out in hard/dense soil

Excavation in trenches not exceeding 1.5 m width and not exc 1.5 in depth getting out soft disintegrated rock

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm in thick using excavated hard/dense soil.

Removal of surplus soil to a distance not exceeding 50 m and depositing where directed by Engr-in-charge.

Supply and laying of 25mm dia CPVC pipes SDR 11 and plain CPVC SDR 11 fitting in trenches complete all as specified.

Supply and Fixing Gun metal Globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed in 25mm dia pipe.

Supply & Fix in repair Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe of dia 25mm and fixed.

Schedule 'A' Part II E/M Portion External Water Supply

Supply and install hi wall split units indoor/outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 3 star rating and EER 3.2 of capacity 2 TR with copper tubing condensor including inverter technology all necessary fixing arrangement and accessories including mounting bracket for outdoor unit.

Supply and fixing of voltage stabilizer for automatic operation single phase naturally air cooled indoor type and designed for input variaiton between 170 volt to 250 volt with output voltage stabilised at 230 Volt with accuracy of ± 2.5% for 2 Ton AC complete all as specified and directed by Engr-in-charge

SHREE SAI LABOUR CONTRACT CO-OPERATIVE SOCIETY LTD

M/S jvsr constructions

SAGAR ENTERPRISES

M/S. M M S ENTERPRISES

Tara Construction