GE/863/EWS-T-77 OF 2025-26 COMPREHENSIVE BR REPAIR IN DIFFERENT BLDGS OF OTM ACCN

Amount

Demolition of cement concrete (un-reinforced) in ground floors and pavings n. exc 15 cm thickness (below or above ground level) all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons Laid, bedded and pointed in any mortar etc.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated/crimped steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F 0.63mm thick Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 120gm/sqm.

S &F Plain, galvanised, mild steel sheeting, 0.80 mm thick, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc confirming to Fe 410-W (grade -E-250) quality A complete all as specified and directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quions, arches, pillars, etc but excluding ashlar facings, dressed stonework, precast concrete articles and precast concrete block walling all as specified and directed.

M&L 1:3:6 type C-1 precast cement concrete (20mm graded stone aggregate) block masonary with solid blocks exc 10 cm in width and not exc 20cm in width and setting in cement mortar 1:6.

M&L for 25mm thick cement concrete type B-0, 1:2:4 (using 12.5 mm graded crushed stone aggregate) complete as in levelling of floor etc all as specified and as directed.

M&L for Non skid ceramic coloured (colour & shade as approved) tiles of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors set and jointed in neat cement slurry over and including 15mm thick screed in cement mortar (1:6) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L for Non skid ceramic coloured (colour & shade as approved) tiles of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in Skirting/dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including 10 mm thick rendering in CM (1: 4) complete all specified and directed.

M&L glazed tiles digital/designer coloured ceramic tiles 300x450x7mm thick in vertical surfaces ( including scaffolding)such as wall lining set and jointed in neat cement slurry pointed in coloured cement to match including 15 mm thick plastering in CM 1:4, design Colour and pattern as approved by GE complete all as specified and directed.

M&L for Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles, throating and necessary form work complete all as specified.

S&F machine made precast cement concrete blocks (coloured interlocking paver) of 60mm thick with grey cement and pigment over 25mm thick sand cushion complete all as specified and directed. (Note : Sand cushioning will be measured and paid seprately).

M&L 75 mm thick PCC in 1:4:8 type D-2 using 40mm stone aggregate as in sub base etc complete all as specified.

Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

Taking down cement plaster, any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M & L for rendering 15 mm thick on stone masonry surfaces or surface other than fair face of brick-work or concrete surfaces in cement mortar 1:4 and finished even and fair complete all as specified and directed.

M & L for rendering 10 mm thick on stone masonry surfaces or surface other than fair face of brick-work or concrete surfaces in cement plaster 1:6 and finished even and smooth (without using extra cement).

M&L for preparation of newly plastered surface of walls and applying two coat of cement base paint over a coat of Chalk whitening complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coat of oil bound distemper on walls over a coat of wall care putty, complete all as specified and directed.

Taking down chowkats or frames exc 1.5 sq.m but n.exc 4 sq.m each but with shutters (without taking off shutters from the frames).

Taking down chowkats or frames not exc 1.5 sq.m each but with shutters (without taking off shutters from the frames).

S&F of factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made of MS tubes for top & bottom rail. MS frame shall be covered with heat moulded wood grain printed PVC sheet ‘C’ channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheet for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of wood grain PVC sheet to be fitted to the MS Frame/sealed to the stiles & rails with suitable PVC sheet beading, & 5mm thick x15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90) degree used and joined together with solvent cement, all as specified.

M/L for solid PVC door frame of size 50x47mm made out of 5mm thick wood grain printed pvc sheet reinforced with MS square tube all as specified.

S&F box type steel windows with side hung shutters including projecting type hinges with steel handle and steel peg stay complete with glazing bars dovetailed or welded, complete all as specified and directed.

All as per item No 30 but without glazing bars

Supply and fabrication of framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified.

M & L for preparation of new or previously untreated surfaces of steel of any description , over 10 cm in width or girth not otherwise described applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer.

S&F in Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples complete all as specified.

S&F 3.00 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S & F 150mm Aluminium handles, cast type, anodised

S&F 150mm long aluminium, anodised barrel tower bolts of extruded section, all as specified and as directed by the Engr-in-charge.

S & F 100 mm butt hinges, medium weight, cold rolled mild steel and fixed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness inclduding cover fillets.

Taking down wall panelling and similar work complete all as specified and as directed.

M& L for Hollow PVC wall lining consisting of 5mm thick single side prelam PVC sheet instead of plain colour sheet inclusive of solvent cement and fixing on PVC frame as per specified in MES schedule part-I & II complete all as specified and directed by Engineer in Charge .

S&F in repair stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement. complete all as specified and directed

S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified complete all as specified and directed.

S&F anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc complete all as specified and directed.

M&L for 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC/aluminium frame as per specifications complete all as per specified and directed.

S&F 4.8 mm thick Sheet glass, ordinary quality exc 0.5 Sqm in each pane and glazing with rubber gasket/ neoprene pad etc for aluminum door complete all as specified and directed

S & F 200 mm aluminium, anodised, barrel tower bolts of extruded section and fixed.

S&F mortice brass lock vertical type size 100mm with 4 levers complete all as specified and as directed.

S&F Aluminium (die cast ) body door closer hydraulically regulated designation No 3 universal type, suitable fo door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg. Complete all as specified and as directed.

M&L for complete removal of existing treatment on wall surfaces and sanding the surface to prepare the surface even & smooth to recieve paint and apply two coat of distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification using paint roller technology over a coat of wall care putty complete all as specified (Note : Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm)

M&L for complete removal of existing treatment on wall/ roof projections including facia, cornices etc by scrapping and applying a coat of wall care putty including sanding the surface to prepare the surface even and smooth and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives @ 1.43 litre/ 10 sqm over over a priming coat of exterior primer applied @ 0.90 litre/ 10 sqm. Complete all as specified and directed at any height incuding necessary scaffolding over new/complete removal surfaces. (Note : Sanding of surface to be done by mechanical sander with 1500 - 2700 rpm)

M&L for preparation of old steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old wood or wooden based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Schedule of Credit

M/S SHIV NATH ENTERPRISES (BID ID -3510508)

M/S J.S.ENTERPRISES (BID ID -3508029)