SPECIAL REPAIR TO P-33 (QUARTER GUARD ) OF GUARD AT JALIPA MIL STN UNDER GE (A) BARMER

M&L for rendering 15mm thick in CM (1:6) on on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing surfaces, trowelled to even and fair finish without using extra cement including taking down of old plaster of any thickness complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls, and applying two coats of oil emulsion distempering over a coat of interior wall primer and 2.00 mm thick wall care putty complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of walls, and applying three coats of white wash complete all as specified and directed.

M&L for Rubber Moulded glossy finish precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment.

S&F for Steel work in tubular trusses,post,purlin,rafter including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240

M&L for rendering 5mm thick in CM (1:3) as on concrete surfaces in ceiling finished even and smooth without using extra cement including taking down of old plaster of any thickness all as specified.

M&L for preparing new plastered or unplastered surfaces of ceiling, and applying three coats of white wash complete all as specified and directed.

M&L for complete removal of existing treatment, plastered or unplastered old surfaces of walls, including filling of cracks/holes by crack filler, removing unnecessary nails applying two coats of oil bound distemper/ emulsion over a coat of interior wall primer over 2mm thick wall care putty complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:4) with using WPC on stone masonry surfaces or surface other than fair face of brick-work or on one side of lathing surfaces, finished even and smooth without using extra cement including tacking down of old plaster of any thickness complete all as specified and as directed. Note : WPC shall be measured and paid separatley.

M&L for preparation of new plastered surfaces of walls and applying two coat of Premium acrylic emulsion paint over a coat of primer complete all as specified and directed.

M&L for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm, including complete removal of existing treatment, plastered or unplastered old surfaces of walls, complete all as specified and directed.

Supply only integral liquid water proofing compound complete all as specified and directed.

M&L for complete removal of existing treatment, plastered or unplastered old surfaces of walls, including filling of cracks/holes by crack filler, removing unnecessary nails and applying three coats of white wash complete all as specified and directed.

Demolition of stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for Glazed ceramic tiles of size 350mm x 250mm x 7mm/ 450mm x 350mm x 7mm thick (coloured) of superior quality fixed on vertical surfaces such as skirting/dado etc, set and jointed in neat cement slurry over 10mm thick backing coat in CM (1:4) and pointed in coloured cement to match complete including dismantling of old tiles& cement mortar bedding of any thickness and nature all as specified and directed.

M&L for non skid ceramic tiles of size 7 to 8mm thick (coloured) (Square/rectangular) area of each tile exc 0.18 but n exc 0.38 sqm, in floors, set & jointed in neat cement slurry and pointed in coloured cement over 15mm thick screed bed in CM (1:4) complete including dismantling of old tiles & cement mortar bedding of any thickness and nature all as specified and directed.

M & L for Virified Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc over 15mm thick screed bed in CM (1:4) complete including dismantling of old tiles & cement mortar bedding of any thickness complete as directd.

M & L Virified Ceramic tiles 8 to10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc including 10mm thick backing coat in CM 1:3 and dismantling of old tiles along with cement mortar bedding complete as directd.

M&L for 30mm thick PCC 1:2:4 Type B1 with 20mm graded stone aggregate as in levelling course in floor complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) as in plinth protection including making joint at every 3mtr interval and at corner and filled with mixture of bitumen and sand and finished even and fair and laid in alternate bays complete all as specified and directed.

M&L for complete removal of existing treatment, plastered or unplastered old surfaces of ceiling, including filling of cracks by crack filler, removing unnecessary nails and applying three coats of white wash complete all as specified and directed.

M & L for Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar over 10 mm thick cement plaster 1:3 jointed and pointed with grey cement slurry mxed with pigment to match the shade of the slab including rubbing and polishing complete, all as specified and directed.

M&L for 20mm thick Granite (of any type in single piece) work (table rubbed and polished including rounding edges) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed in CM (1:4), set jointed & pointed in neat cement slurry complete all as specified and as directed.

Taking down chowkhats or frames (without taking off shutters from the frame) n. exc 1.5 Sqm complete all as specified and directed.

Taking down chowkhats or frames (without taking off shutters from the frame) exc 1.5 Sqm and n. exc 4.00 Sqm complete all as specified and directed.

M&L for Pressed steel frames size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and as directed.

S&F for 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

M&L for preparation of New or previously untreated wood and wood based surfaces of any description over 10cm in girth or width and painting with two coats of synthetic enamel paint over a coat of primer complete all as specified and directed.

Powder coated 50 microns extruded aluminium glazing/ doors & shutters made out of section 63.5x38.10x1.29mm for chowkats or frame & shutters made of size 44.45x44.45x1.29mm for side rails and middle rail, 114.3X44.45X1.29mm for top rails and bottom rails and including 12mm thick High Density Fibre Board pre-laminated on both sides (water proof) below middle/lock rail and 5mm thick tinted glass above middle/lock rail and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beads 20mm size with and incl mortice lock with duplicate keys etc complete all as specified and directed approved by accepting officer including supply and fixing the following items: (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 3 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 200mm long - 2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf

Supply only chicken wire mesh 22 gauge of size not less than 20X20mm all as specified and directed by Engineer-in-Charge. Make : Swastik or equivalent as approved

M&L for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge.

M & L for Machine cut kota stone slab flooring 20-25mm thick over, laid over cement screed base , jointed and pointed with grey cement slurry mixed with pigment over 20mm thick cement mortar 1:6 screed bed to match the shade of the slab including rubbing and mirror polishing and including 50 mm to 75 mm wide Jaisalmer sand stone border all around in rooms and varandhas complete all as specified and directed. Note : Work will be in patches or in bulk

S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire stapples complete all as specified and as directed. and directed.

S&F for PVC door frames of sizes 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS Square tube in opening of suitable size complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick with particle board core (stile:), with 2,4 or 6 raised panel design with 5mm thick Moulded PVC Sheet on the front Face & 2mm Plan colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

S&F for 100mm long butt hinges medium weight cold rolled mild steel complete all as specified and as directed.

S&F for 150mm long Aluminium anodizes barrel tower bolts of extruded section complete all as specified and as directed.

S&F 150 mm size aluminium anodized handle complete all as specified and as directed.

M&L for 300mm long aluminium alloy anodized sliding door bolts with Hasp and staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

Dismantling of boarding any description fixed in any position with nails complete all as specified and directed

M&L for providing & fixing 12mm thick gypsum baord in celing (two or three stages if reqd) including GI U-section 50mmx35mmx7mm & edge side GI U-section size 30mmx25mmx15mmx7mm fixed with screw gypsum board and frame grid suspended with soffit cleat to roof slab for hanging 4mm dia GI hanger rod with adjustable level clips, after fixing of gypsum board jonits/junction of gypsum board ceiling to be covered with 50mm to 100mm corner strips, Round at fan & lights, cut for cassette AC indoor unit , light and Gypsum cornice all around the wall of any design and size as requried by user complete all as specified and as per manufacture's instruction and applying two coats of Luster Paint over 3 mm POP to visible side of gypsum board ceiling shade/tint and including necessary scaffolding for the work complete all as specified and directed by Engr-in-Charge

S & F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all respect including supply and fixing of all accessories like fasteners/screws/solvent etc all as recommended by manufacturer all as specified (colour/pattern as approved by Accepting Officer).

S&F of 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

S&F in repair 25mm dia fancy stainless steel curtain rod with fancy fixing brackets, fancy stops/supports, rollers etc. complete all as specified.

S&F in rep vitreous china squatting pan 'Orissa' patern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistrern and flush pipe) including connection to drain (or outgoing pipe) and making good to the floor complete all as specified.

S&FVitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)including seat cover complete all as specified and directed

S&F in repair PVC valveless flushing cistern, low level white with inlet ball valve float and handle including brackets complete fixed capacity of flush 10 ltrs complete all as specified and as directed.

S & F table top wash hand basin vitreous china coloured including CI bracket, 15mm dia polythene connection, 32mm dia chromium plated (CP) waste coupling chain and plug waste filling union and 32mm dia PVC waste pipe 90cm long, all necessary inlet outlet connections complete all as specified and directed. Make : Hindware or equivalent model in Cera /Parryware/ Neycer as approved by GE.

S& F Brass CP Wash basin mixer for mixing hot & cold water screwed down for15 mm size iron pipe and fixed

S&F in repair 15mm bore Bib taps CP fancy type, cast copper, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F in repair 15mm bore, 450mm long, PVC connections with brass unions internally threaded both ends complete fixed to iron pipe at both ends as fixed in repairs complete all as specified and as directed..

S&F in repair CP fancy type stop valves ,cast copper alloy, screwed both ends for iron pipe or for union of 15mm bore complete all as specified and as directed.

Dismantling of water tanks (RCC hume Pipe/PVC) including disconnecting all connections etc. complete for following capacity of tanks :- 1000 ltrs

S&F for new rotational moulded polythylene water storage tank (cylindrical/vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing brass ball valve high pressure with polythene float and fly nut, 20mm bore complete for following capacity of tanks :- 1000 ltrs

S&F for 16mm bore of CPVC of food grade pipes SDR 11 and plain CPVC SDR 11 fittings on walls/ceiling or laying i

n floors including tacking down of old pipe complete all as specified and directed.

S&F 20mm boreTubes, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including tacking down of old pipe complete all as specified and as directed.

S&F 25mm boreTubes, `medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors including tacking down of old pipe complete all as specified and as directed.

S&F in repair 20mm bore Gun metal gate valves with iron wheel head screwd both ends for iron pipes complete all as specified and directed.

S&F in repair 25mm bore Gun metal gate valves with iron wheel head screwd both ends for iron pipes complete all as specified and directed.

S&F in repair brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges.

Dismantling of soil, rain water pipes with fittings of any description complete all as specified and as directed.

S&F for 75mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall complete all as specified and as directed.

S&F for 110mm bore of PVC (SWR) pipes single socketed in any length with rubber ring joints laid on wall complete all as specified and as directed.

S&F for 75mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F for 110mm bore PVC (SWR) bend any radius complete all as specified and directed.

S&F for 75mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

S&F for 110mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

S&F for 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F for 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F for 75mm PVC (SWR) vent cowl complete all as specified and directed.

S&F in repairs 75mm bore PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F for 110mm PVC (SWR) vent cowl complete all as specified and directed.

S&F in repair stainless steel soap dish, approximate size 130x120x30mm complete all as specified and as directed.

S&F in repair sheet glass corner wall mounted shelf assembly consisting of 5.5mm thick sheet glass 220mmX220mm size with chromium plated bracket guard and railing 50mm high complete all as specified and as directed.

M & L for half stall ceramic urinal pastel coloured of size 720x485x310mm (Make - Hindware Cat No. 60006 or equivalent approved make indicated in list of make in tender) including Urinal toughned glass / Marble / Granite including grinding, polishing, rounding/moulding/chamfering edges), brass cp bottle trap, electric operated auto censor / Push cock (Including spraders ) flushing arrangements. (Make Hindware Cat No. 500963 or equivalent approved make indicated in list of makes in tender) complete including taking down old u/s one complete all as specified and directed. Note : Type of partition will be decide by Engr-in-charge as per sitr requriment 2) Type of flushing arrangement will be decide by Engr-in-charge.

Cutting chases in stone, concrete block or slab walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth all as specified and as directed.

Dismantiling wrought iron or mild steel work of any description not otherwise provided for etc comoplete all as specified.

S&F for MS framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; cooler stands, railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 all as specified and as directed.

M&L for preparation of New or old previously untreated steel or iron surfaces of any description over 10cm in girth or width and painting with two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for preparation of old painted steel or iron surfaces of any description over 10cm in girth or width and painting with two coats of synthetic enamel paint complete all as specified and as directed.

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work.

M & L for RCC (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) in chajjas.

Formwork to chullah hoods, chajjas, troughs and similar items including edges, flat rough finished surfaces of concrete

M&L for Pre-cast cement concrete block masonry Type C1 1:3:6 (20 mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in CM (1:6) complete all as specified and directed.

M&L for rendering 15mm thick plaster in CM (1:4) on faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and as directed.

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in concrete bed to 150mm bore drain pipes including packing under & haunching against the sides of pipes after they are laid & tested for 150mm bore pipe including demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement concrete mortar complete all as specified and as directed.

M&L for Reinforced concrete pipes 150mm bore class NP-2, laid and jointed complete with collars, complete all as specified and as directed.

M&L for precast cement concrete 1:2:4 type B-1 using (20mm aggreates) set in CM (1:4) as in cover slabs (for manhole etc) & simillar articles with plain faces complete (Reinforcement will be measured and paid separatly) all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and n exc 1.5 m in depth and getting out hard/dense soil.

Returning, filling in including spreading, levelling, watering & well ramming in layers n.exc 25cm.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5 m above the starting point complete

M&L for applying neat cement slurry with 3 kg of cement per sqm with mixing of liquid water proofing compound as per manufacturer instructions over surfaces roof, terrace, projection, chajjas, walls after prepration and cleaning of surfaces complete all as specified and directed.

M&L for rendering 10mm thick cement plaster in CM (1:3) on concrete surfaces of roof, terrace, projection, chajjas, walls (old or new), finished even and smooth (without using extra lime or cement) with mixing of WPC as per manufacturer instructions complete all as specified and directed. (Note : WPC shall be measured and paid separately)

M&L for Applying evenly a priming coat with bituminous primer at 4 Kg per 10 sq metre over plastered/concrete surfaces including prepration complete all as specified and directed.

M&L for laying of APP based polymeric membrane minimum weight 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150gm/sqm) by torched applicatilaid over and including applying evenly a tack coat of industrial bitumen S-35 grade (30/40) at the rate of 1.2 kg per Sq.m including cleaning surfaces by on and as per manufacturer instructions complete and all as specified and directed.

M&L for 40mm thick cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) over roof, terrace using integral WPC as per manufacturer's instructions well compacted and fair finish and forming "V" grooves both way at 1.20 Rm intreval in concrete surfaces of roofs or terracing n exc 10mm wide and n exc 10mm deep, cleaning out and filling solidly with a hot mixture of bitumen and clean dry sand 1:1 (by weight)complete all as specified and directed.

M&L for Providing cement concrete cement concrete in roof ke

rbs or mud stops, rounded or chamfered on edges (1:2:4) type Bo(using 12.5 mm graded stone agg) for coved fillets of radius 75mm provided at junction of roof and parapet/vertical surfaces, pedding concrte to achive slope as required & making plateform for water tank on roof slab etc complete and all as specified and directed.

M&L for Chipping of slab/columns/beams/chajjas/parapet/roof projection/balcony/ staircase and removing loose mortar with chisel hammer without much impact on concrete surface, clean the surface by sand blasting the surface using river sand with minimum of 6 kg pressure at the nozzle or air blow by electric pressure blower by mechanical compressor, cleaning the exposed reinforcement with wire brushes etc and disposal of debris foe all lead and lifts, all complete all as specified and directed.

M&L for Cleaning & applying rust remover (CICO Clean-o rust) in two coats over rusted reinforcement surface and providing anti corrosive coating with two component epoxy based zinc rich primer/Rust passivation Inhibitor coat at the rate of 2-3 sq. mtr/ltr not less than 50 microns dft with CICO ZINCILATE-500 or equivalent to reinforcement surface as per manufacturer’s instructions including all machinery, tools tackles and clearing of debris. Make: CICO clean-O-rust, CICO ZINCILATE-500 or equivalent in Fosroc/Dr Fixit/ACC/L&T/STP

S&F of new steel or rebars by drilling holes with 10 mm to 20mm dia and 100 to 200mm deep as per IS code of 10D formula and filling the holes after inserting of reinforcement dia 8 to 16mm for anchoring at ends/shear connector and filled the holes with one or two component styrene free vinylester resin anchor or two components, styrene & cement free epoxy- acrylate fixing and anchoring compound ( having the technical parameters mentioned in material specifications) using standard sealant applicator gun after drilling holes of required diameter at required locations, for holding / fixing / placing in position the steel mesh reinforcement at desired level/ stretching. (Note : Steel/reinforcement shall be paid and measured separately) . Make: CICO RESIFIX-G or equivalent in Fosroc lokfix/Hilti and Master builder (BASF)

S&F for Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified

M&L for providing 25mm average thickness of Micro concrete M-50 (Minimum grade) with CICO MICROCRETE at the rate of 25kg per 0.0125 m3 with 20% properly graded 5mm to 10mm silt free aggregate as per manufacturer instructions and mixing concrete with mechanically electrically operated mixer machine, including all necessary scafolding if required etc all as specified and directed. Make: CICO Technologies Ltd, M/s Sika India Pvt Ltd, M/s Bostik India Pvt Ltd, M/s Choksey chemicals Pvt Ltd, M/s Thermax Ltd, M/s Master builder solution (BASF) or techno commercially equivalent.

M&L for providing Micro concrete with CICO MICROCRETE at the rate of 25kg per 0.0125 m3 with 20% properly graded 5mm to 10mm silt free aggregate as per manufacturer instructions and mixing concrete with mechanically electrically operated mixer machine etc all as specified and directed. Make: CICO MICROCRETE of CICO Technologies ltd or equivalent in Fosroc/STP/BASF

M&L for Formwork for flat finished surfaces to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

M & L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, in hard / dense soil returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm,

S&F for MS framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; cooler stands, railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 all as specified and as directed.

M&L for PCC 1:4:8 type D-2 (using 40mm gde agg) as in foundation and mass concrete complete as specified and directed by Engr-in-Charge.

M&L for 2mm thick Fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof/chajjas, wall etc., complete all as specified and directed.

M & L Hardcore using broken stone boulders not exceeding 63mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surfaces complete all as specified & directed.

M&L 75 mm PCC 1:4:8 type D-2 as in sub base complete all as specified and directred

Supply only Fine aggregate (sand) for sand cousioning

Taking down old, unsv aluminium/copper point wiring (light, fan, socket or power) complete, incl fixture & fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc. including Cost of making good the disturbed surfaces is deemed to be included in the unit quote rates, complete all as specified and directed by Engr-in-Charge.

Taking down old sub-main wiring incl fixture & fittings etc. removing materials to store for keeping in safe custody or for taking credit & making good the disturbed surfaces of walls, floors, etc., v complete all as specified and directed by Engr-in-Charge.

Disconnecting/dismantling of old existing un serviceable DB's along with metal enclosue concealed in walls of any type/way 240/415 Volts with their old/un serviceable burnt MCCB/MCB's etc.incl making good the disturbed surfaces and matching with existing surfces, including Cost of making good the disturbed surfaces is deemed to be included in the unit quote rates, complete all as specified and directed by Engr-in-Charge.

M & L for concealed point wiring with two single core 1.5 sqmm PVC insulated, unsheathed, FRLS cable, 1100 volts grade, ISI marked with multi stranded copper conductor drawn through and including non-metallic PVC rigid conduit (me

dium grade) with all fittings and accessories ISI marked incl provision of 1.5 sqmm PVC insulated, multistranded, unsheathed, copper conductor cable, FRLS, ISI marked as earth continuity conductor (green in colour) & incl fixing of modular metal flush boxes of appropriate size & thickness fixed flush to wall for mounting switch, sockets etc. with including cutting chases for conduits & sinkings for modular boxes & making good the disturbed surfaces, matching to the existing one etc., suitable for One Light/fan/Call Bell etc. point controlled by one switch 5/6 Amps, complete all as specified & as directed NOTE : 1) Modular metal flush boxes shall be measured & paid separately. 2) Cutting chases & making good the disturbed surfaces is deemed to be included in the unit quoted rates. 3)-The make/model of modular metal flush boxes & modular cover plates shall be same as that of modular switches & sockets. Make of cable : Havells/Polycab/Finolex.

All as item No. 121.00 here-in-above but suitable for One switch socket outlet point 5/6 Amps on independent board.

All as item No. 121.00 here-in-above but suitable for with FRLS PVC insulated copper conductor cable of size 2.5 Sqmm and 2.5 Sqmm for earth continuity conductor green in colour for 16A switch socket complete.

M & L for concealed sub-main wiring alongwith earth wire of size (2 x 4.00) sq. mm + (1 x 4.00) sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including non-metallic PVC conduit (medium grade) with all fittings and accessories ISI marked for conduits & sinkings for modular boxes & making good to walls, floors,ceiling etc. complete all as specified & as directed. Make of cable : Havells/Polycab/Finolex.

M & L for concealed sub-main wiring alongwith earth wire of size (2 x 6.00) sq. mm + (1 x 6.00) sq. mm earth wire, ISI marked, FRLS, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including non-metallic PVC conduit (medium grade) with all fittings and accessories ISI marked for conduits & sinkings for modular boxes & making good to walls, floors,ceiling etc. complete all as specified & as directed. Make of cable : Havells/Polycab/Finolex.NOTE for item No 6.00 & 7.00 : 1) Two runs of PVC wire, one run of earth wire & one run of PVC rigid conduit (medium grade) will be measured as one length. 2) Modular metal flush boxes (if req) shall be measured & paid separately.2) Cutting chases & making good, including necessary Putty work of the disturbed surfaces is deemed to be included in the unit quoted rates.

S & F Modular switch, one way, 6 Amp, 1 Module, 240 volt complete all as specified and as directed. Cat No : ACVSXXW061, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

S & F Modular switch with indicator, one way, 16 Amp, 1 Module, 240 volt complete all as specified and as directed. Cat No : ACVSXIW161, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

S & F Modular shuttered socket outlet 3 Pin, 6 Amp, 2 Module, 240 volts, ISI marked complete all as specified and as directed. Cat No : ACVKSWW063, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

S & F Modular shuttered socket outlet 3 Pin, 6/16 Amp, 2 Module, 240 volts, ISI marked complete all as specified and as directed. Cat No : ACVKCWW163, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 1/2 modules all as directed. Cat No : ACTXMIIX01/02, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 3 modules all as directed. Cat No : ACTXMIIX03, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 4 modules all as directed. Cat No : ACTXMIIX04, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

Supply & Fixing and concealing modular metal flush box suitable for fixing switches/sockets of 8 modules all as directed. Cat No : ACTXMIIX08, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 1/2 modules all as directed. Cat No : ACVPPCWV01/02, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 3 modules all as directed. Cat No : ACVPPCWV03, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 4 modules all as directed. Cat No : ACVPPCWV04, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

Supply & Fixing modular cover plate suitable for fixing switches/sockets of 8 modules all as directed. Cat No : ACVPPCWV08, Model - Verona of make CRABTREE (Havells) or techno-commercially equiv In Legrand/Anchor Roma

S&F ceiling rose surface PVC/ Polycarbonate, Isolated body with face Bakelite three terminal complete all as specified and directed. Make: Havells/CG/Anchor

S & F LED batten suitble for indoor application 20 W, 4' length , wall/surface mounted with aluminium housing, end cap made of ABS plastic of white colour finish and high efficiency translucence (HET) diffuser and integral electronic driver including two point surface mounting on wall/ ceiling and connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed by Engr-in-Charge

S & F LED batten suitble for indoor application 10 W, 2' length , wall mounted with aluminium housing, end cap made of ABS plastic of white colour finish and high efficiency translucence (HET) diffuser and integral electronic driver including two point surface mounting on wall/ ceiling and connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed by Engr-in-Charge

S&F in replacment Gate/Lawn Post top lantern LED light fitting of 15 Watts LED Coral type with spun aluminium landscape luminaire,Opal PC Cover offers soothing uniform illumination with IP 65 protection with Suitable fixing Nuts for fixing the fitting including taking down the u/s fitting complete all as specified and directed by Engr-in-Charge. Make : Havells/Philips/Wipro/Crompton

Supply and lay in repair LT service cable 6 sqmm 2 core inside PVC conduit 20 mm dia medium grade for landscape lighting/ garden lighting inside trench or on wall/floor complete all as specified and as directed. Note: The rate quoted must be inclusive of laying the cables in trench at max 10 cm depth or mounting on floor/wall

Supply and fix in repair recess mounted low glare LED panellight 2'X2' size 36 watt white/warm white for armstrong/grid ceiling or similar ceiling mounting system complete prewired using 1.5 Sqmm FRLS PVC insulated (Unsheathed) 3 core copper conductor cable, 1100V grade including taking down old complete all as specified and directed. Make: BAJAJ/Wipro/Crompton/Havells

S&F in replacement LED Bollard Garden ligtht of 9W with excellent light output through its PMMA Windowsensuring maximum illumination surrounding with IP 65 protection of Height <1 Mtr with fixing accessories including taking down the u/s fitting complete all as specified and directed by Engr-in-Charge.

S & F in repair 15 watt LED Up-Down light flat down light back lit, recess mouting cylindrical surface type as per site conditions warm white/white including taking down old complete with all a

ttachment all as specified and directed Make - Crompton/ Havells/ Philips/Bajaj/Wipro

S&F and refixing single pole 06 to 32 A rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) in the MCB DB complete with connection testing andcommissioning, complete all as specified and as directed

S&F and refixing single pole 32 to 40 A rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) in the MCB DB complete with connection testing andcommissioning, complete all as specified and as directed

S&F inrepair MCB TPN 63 A rating complete all as specified and as directed