CA NO CWE/CHM-36/2019-20 PROVN OF FURNITURE FOR SPORTS INFRASTRUCTURE GYM AND SQUASH COURT ( K AREA ), TRANSIT SINGLE OFFR ACCN FOR WARCEN (16 NOS) AND RENEWAL OF FURNITURE AGAINST SURVEYED OFF FURNITURE AT MIL STN CHANDIMANDIR

Amount

PEG TABLE (DRG NO FD-277) Ist class seasoned teak wood shall be used through out. Top shall be made out of pre-laminated particle board 18/19 mm thick ISI marked exterior gde, 6 mm thick teak wood beading shall be used all around at top. Rubber PVC shoes shall be provided at the bottom of legs duly screwed. All wooden surfaces shall be French polished to a glossy finish . Rest all asl as shown on Drg No FD-277 complete all as specified and directed.

CHAIR WRITING MAP(DRG N0 FD/MAP/E6/12) (a) All wood work shall be of 1st class hard wood (Teak). (b) Seat shall be 75 MM thick foam of 32 density covered with good quality tapestry cloth (cost of cloth not less than Rs 450/- per meter) as approved by GE over 12MM thick commercial plywood as per IS-303. (c) Nylon buffers of appropriate size shall be screwed to the bottom of each leg. (d) All exposed surfaces of timber and plywood shall be french polished. (e) All joint fixing shall be done in accordance with standard workmanship and specification. (f) Rest all as shown on drawing.

SOFA CHAIRS(DRG N0 FD-281) The sofa chair shall be single seater with arms. Timber work shall be of Ist class seasoned teak wood. Foam shall be 100 mm thick cushion of ‘cool’ foam of 40 density of size 550 mmx525mmx100mm covered with best quality tapestry cloth rate not less than Rs. 450 per meter. of approved make. All wooden surfaces exposed to view shall be French polished and all as per drg No FD-281 complete all as specified and directed.

TABLE CENTER (DRG NO FD-274) Ist class seasoned teak wood shall be used through out. Top shall be made out of pre-laminated particle board 18/19 mm thick ISI marked exterior gde. 6 mm thick teak wood beading shall be used all around at top. Rubber PVC shoes shall be provided at the bottom of legs duly screwed. All wood surfaces shall be French polished to a glossy finish and all as per drg No FD-274 complete all as specified and directed.

TABLE WRITING (DRG NO FD-275) (a) All wood work shall be of 1st class hard wood (Teak). (b) Irrespective of what is shown in the drawing top of table shall be of 18MM thick Pre-laminated particle board exteir grade as specified here-in-before 4MM thick teak wood edging shall be provided all-round. (c) Front of drawer and shutter of cabinet ( below drawer) shall be of 18MM thick Prelaminated particles board ( Prelaminated perticale board exteir grade as speicified here-in-before sides, bottom and shelf of cabinet shall be of 18 MM prelaminate perticale board as per drg . (d) Bottom of drawer and back cabinet shall be of 6MM thick commercial plywood as per IS - 303. (e) All exposed surfaces of timber & wood based surfaces ( except laminated surfaces) and prelaminated particle board and 4mm teak wood bedding shall be French polished. (f) All joints fixing shall be done in accordance with standard workmanship and specification. (g) Rest all as shown on drawing and as directed by GE/Engr-in-charge.

Table dressing gents with mirror (Drg No FD-230) All wood shall be of Ist class hard wood teak .The bottom side of dressing table shall be of 18/19 mm thick prelaminated pertical board. Top shall be of 19 mm thick commercial particle board . Frame work of mirror shall be of Ist class teak wood back shall be of ply wood 6 mm commercial ISI marked, Mirror shall be 5 mm thick ISI marked. Make of mirror shall be Atul/Modi. All wooden surfaces shall be French polished to a glossy finish and all as per drg No FD-230 complete all as specified and directed.

Mirror 180x45 cm (DRG NO FD-54(M)) Overall size 1200 x 1200 x 5.5mm thick mirror of Swastic or Modi Guard or Atul Mirror. Free frame distortion and other deflects shall be provided on 6mm thick ply wood backing. The Mirror and ply wood backing shall be enclosed in the Teak wood from 25mm x 30mm in section made to shape as specified and directed by Engineer-in-Charge. 12mm x 12mm in section teak wood beading shall be provided at the back of mirror. All wood surface exposed to view when placed imposition shall be French polished with high gloss finish. 3mm thick flat iron key plates of MS 25 x 25mm in section shall be provided.

Chair Eazy folding (DRG NO FD-17M) :- Material incorporated and workmanship shall be of high standard ccomplete as per drg and as directed by Engineer-in-Chief.

TEAPOY WOODEN (DRG NO FD-278) All as shown on drg. Overall size of peg table shall be 600mm long, 450mm wide 540mm high. All wood shall be of Ist class teak wood. Top of table shall be made out of prelaminated particle board 18mm thick exterior grade and 4mm thick teak wood beading shall be provided all round the table irrespective of what is shown on drg and all as per drg No FD-278 complete all as specified and directed.

CHAIR EASY (DRG NO FD-229) Teak wood seasoned Ist class shall be used through out . Canning shall be done with cane plastic 2 mm thick and 3 mm for border. Cane plastic shall be used of premier/Usha make. All exposed surfaces shall be french polished to a glossy finish and all as per drg No FD-229 complete all as specified and directed.

SOFA SET 5 SEATER (DRG NO FD-373) The set shall consist of one long piece of three seat and two small pieces of one seat each. . Timber work shall be of Ist class seasoned teak wood. Foam shall be 100 mm thick cushion of ‘cool’ foam of 40 density of size 550 mmx525mmx100mm covered with best quality tapestry (cloth rate not les than Rs. 450/- per metre) of approved make. All wood surfaces exposed to view shall be French polished and all as per drg No FD-373 complete all as specified and directed.

SOFA SET 4 SEATER WITH DETACHABLE DRG NO (FD-281) The set shall consist four small pieces of one seat . Timber work shall be of Ist class seasoned teak wood. Foam shall be 100 mm thick cushion of ‘cool’ foam of 40 density of size 530mmx500mm covered with best quality tapestry (cloth rate not les than Rs. 450/- per metre) of approved make. All wood surfaces exposed to view shall be French polished. Rest all as per drg No FD-281 complete all as specified and directed.

BED WITH PLYWOOD TOP DRG NO (FD-246) All material incorporated and workman ship shall be of high standard complete all as directed by Engr-in-Charge and as shown on drg.

TABLE DRESSING LADIES WITH MIRROR (Drg No FD-251) All wood shall be of Ist class hard wood teak .The bottom side of dressing table shall be of 18/19 mm thick prelaminate perticale board & prelaminated particle board 18/19mm on other side. Top shall be of/18/19 mm thick prelaminated particle board Frame work of mirror shall be of Ist class teak wood back shall be of ply wood 6 mm commercial ISI marked, Mirror shall be 5 mm thick ISI marked. Make of mirror shall be Atul/Modi. All wooden surfaces shall be French polished to a glossy finish nad all as per drg No FD-251 complete all as specified and directed.

BED MAP STEEL (DRG NO FD/E6/MAP/08(R)) (i) Bed hard shall be manufactured all as per details shown in the drawing. All dimensions, shape and size shall be followed as per drawing. (ii) All square and rectangular MS pipes shall be of thickness 18 gauge. (iii) Top of bed shall be of 12mm thick commercial plywood (unpolished) as per IS-303 (iv) Head board and foot board shall be of 18mm thick Prelaminated particle board (both side decorative finish shade as approved by GE ) as specified here-in- before, screwed to MS strip all as per details shown in drawing. Standard PVC edging (minimum thickness 1.6mm) shall be provided alround in Head board and foot board . (v) Hard rubber/PVC shoe shall be provided to the bottom of each leg. (vi) All exposed steel surfaces shall be painted with two coats of synthetic enamel olive green paint over a coat of zinc chromate steel primer. The welding joints shall be filed smooth before application of primer. The surface shall be thoroughly cleaned and prepared prior to application of paint . (vii) Rest all as shown on drawing.

TABLE BED SIDE (MAP) (DRG NO FD/E6/MAP/15(R)) (i) Pipe shall be 18mm MS square pipe (18 gauge) black powder coated. (ii) Top and back portion above top of Table bed side shall be of 18mm thick Prelaminated particle board (one side decorative finish shade as approved by GE and other side white balancing lamination ) as specified here-in- before. Standard PVC edging (minimum thickness 1.6mm) shall be provided alround in top and pull out tray. Back of table bed side shall be of 6 mm thick commercial plywood as per IS-303. (iii) Sides and back of drawers shall be provided with 12 mm thick commercial plywood as per IS-303. Bottom of drawer shall be provided with 6 mm thick commercial plywood. (iv) Movement of Pull out tray and drawers shall be made on teak wood runners. One aluminum anodized handle shall be provided to each drawer. (v) Stoppers shall be 2nd class Hard wood (Sal/benteak/ Bijasal/Hollock). (vi) Hard rubber/PVC shoe shall be provided to the bottom of each leg. (vii) All exposed surfaces of timber and plywood shall be French polished. (viii) All joints fixing shall be done in accordance with standard workmanship and specifications. (ix) Rest all as shown on drawing.

CHAIR CBA STEEL (DRG NO F-120) All as shown on drawing. Legs and frame shall be of 19mm square mild steel tube of wall thickness 1.6mm wood shall be of first class hard wood teak (M) Cane or seat and back shall be 0.4mm thick & 2mm wide weighing not less than 6gm per ten running meter and weaving shall be done in godrej pattern. 20mm thick teak wood plank in one piece shall be provided on right hand side while sitting on chair and shall be hinged on arm rest piano hinge. 20mm thick teak wood arm rest out of 50mmx255mm screwed to legs, on the left side of chair while sitting on chair, shall be provided as shown on drawing. All steel and iron surfaces shall be given two coats of enamel paint over a coat of primer after preparation of surfaces. All wood surfaces shall be French polished with high gloss finish. Hard rubber or PVC shoes shall be provided at the bottom of legs.

FORM WITH BACK STEEL (DRG NO F-78(R) DIMENSION: Over all size shall be of 1800X510X900MM. DESCRIPTION: wooden seat shall be of first class teak wood in one piece and of size 1800mm long 255mm wide and 25 mm thick bolted to frame with 3 mm dia GI nut bolt and washers.Steel frame shall be 1500mm long in such a way that teak wood seat shall project 150mm from frame on each side .Back rest shall be of teak wood and 1800mm long,150mm wide and 19mm thick .The back rest shall be 1800mm long the width is 300mm at bottom and 255 mm at top of wooden plank.Legs shall be 25mm MS tube of wall thickness 1.6mm. Steel frame shall be provided with 25mm square MS tube 16 gauge .All Dimensions, shape and size shall be followed as per drg. FINISH: All wooden expose surfaces shall be french polished two coats after preparation of surfaces and steel portion shall be painted with synthetic enamel black paint

TABLE OFFICE CLERK STEEL (DRG NO FD-1004 DIMENSION: Overall size shall be 1200mm long, 610mm wide and 760mm high. DESCRIPTION:Steel frame shall be of size 1160x570x742mm .four legs of 25mm mild steel tube of 1.6mm wall thickness shall be provided. Top of legs shall be joined together with 25mm square mild steel tube of wall thickness 1.6mm in long and short sides. Two short stiffeners of same size shall be provided at 130mm from bottom of legs. One long stiffener shall also be provided to the middle of short stiffeners. Three drawers of equal size shall be provided on the right hand side above the stiffener at 130mm high with overall size of 350mm wide and 430mm high and 410mm deep..The top of table shall be provided with pre-laminated MDF board of 18/19mm thick with teak veener shade and 4mm thick teak wood edging alround the table .Hard rubber/PVC toes shall be provided to the legs.Locking device shall be provided to drawers. FINISH: All steel surfaces exposed to view when placed in position shall be painted with two coats of silver grey hammer paint internally and extrenally with spray machine after preparation of surfaces.A mark of MES shall also be provided on top left corner of front shutter with visible colour. Painting shall be done with spray machine.Rest all as per drg.

BATH MAT PVC (DRG NO FD/MAP/E6/07) (i) All PVC work shall be of standard class PVC. All dimensions shape and size shall be followed as per drg. (ii) PVC Bath Mat shall be of make blow plast/Neel. Kamal/Supreme/ Cello /Polyset/Brite/syntex. (iii) Hard rubber shoe shall be provided to the bottom of each leg. (iv) Rest all as shown on drawing No FD/MAP/07 complete all as specified and directed.

RECEPTICAL PVC (DRG NO FD/E-6 /MAP/13) (a) Recepticle shall be of covered plastic container of 75 ltr capacity made with thick polymer plastic alongwith lid and handles. Recepticle shall be of bright colours ie. Red,Green,Blue etc. (b) Recepticle shall be of make: Blow plast/Neel Kamal/ Supreme/ Cello/Polyset, as approved by GE.

NOTE FOR ITEM NO 1 TO 21 Drawings and Key specifications for the items are available in GE Chandimandir. The Contractor's are requested to go through the drg/documents before quoting there rates. Nothing shall be entertained at later stage.

M/S Shri Balaji Enterprises