CWE/P-101/2020-21 SPECIAL REPAIR TO BLDG NO NP-07 OR MD ACCN AT CERTAIN UNIT UNDER GE (WEST) PATHANKOT

Amount

Dismantling of floor hearth and wall tiling including cement morter bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M & L for coloured Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) are of each tile exc 0.11 Sqm but n. Exc. 0.18 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer with CM 1:6 complete all as specified and directed.

M & L for coloured Glazed ceramic tiles in vertical surfaces 450 x 350 x 7mm set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick backing coat in cement mortar 1:4, complete all as specified and directed.

M & L for 20mm thick Granite (pure black) work (table rubbed and polished) cills, cooking platforms, in steps, jambs, pillars, window- cills and like in cement mortar (1:4) 10mm thick including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. Note : All Open Edges to be Half rounded & a hole to be made for gas pipe in cooking platform (including RCC slab if required, at no extra cost).

M&L for non abrasive paving ( rectified endura) tiles 300mm x 300mm x 10mm thick machine pressed) (square/ rectangular) polished area of each tile not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement and including 15mm screed bed cement mortar 1:4 to match, complete all as specified and directed

M & L for Demolition of cement concrete (un-reinforced) in ground floors and pavings n.exc 15cm thickness (below or above ground level), complete all as specified and directed

M& L for 75 mm thick PCC as in plinth protection / apron type C-1, 1:3:6 (20 mm graded crushed stone aggregate) finishing cement surfaces even and fair, complete all as specified & directed.

M&L for Coloured chequered cement concrete tiles 200x200x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and pigment laid over and including 50 mm thick PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) and including 15mm thick screed bed in cement mortar 1:6,complete all as specified and directed.

Taking down chowkat with shutter (without taking off shutter from frame) exc 1.5 sqm but n.exc 4 sqm each including iron mongery complete all as specified and directed

Taking down chowkat with shutter (without taking off shutter from frame) n exc 1.5 sqm each inlcuding iron mongery, complete al as specified and directed

Taking down shutter exc 1 sqm but n exc 2 sqm each and remove to store yard, complete al as specified and directed.

Taking down easing and adjusting and refixing shutter exc 1 sq. m and n exc 2 sq. m each in same openinG complete all as specified and directed

S&F of steel window/ventilator factory made out of box type and shutter (double shutter) with sash bar made out of section using flash butt welding hinges shall be provided to both shutters complete including all fittings including 10mm square bar grills, glazing (glass pane), gauging (wire mesh) and one shop coat of red oxide primer all as drg No CEPZ/TD/245/01 sh 1/1 CEPZ- TD/246/01 sheet 1/2 and sheet 2/2, complete all a specified and directed by Engr-in-Charge

S&F of Pressed steel frames 125 x 60 mm for doors with one or more rebates including necessary fixing lugs,MS hinges, lock strike plate,etc.,including filling of cement concrete type B-1 ,1:2:4(using 20mm graded crushed stone aggregate) as in filling hollow of frame with plain concrete and hold fast 300mm FI 25 X 6 three numbers each side, complete as specified and directed.

S&F of Solid PVC door/window frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube, above but wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheet, complete al as specified and directed.

Supply and fixing of factory made solid pannel PVC door shutter 30mm thick (style) consisting of frames made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stile and plain coloured PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement supplying and fixing in the frame at site as per specification complete all as specified and directed.

S&F of second class hard wood Glazed and skelton shutters factory made 35mm thick of 2nd class hard wood rail & style open rebated and prepared to receive glass or wire gauze etc. shutters (without shash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc. size of members of shutters as specified in SSR Part-1, secton 8, clause 8.24(a) kiln seasoned and pressure treated including one coat of pink primer all as specified.

S&F of Plain framed factory made 35mm thick shutter of 2nd class hard wood rail & style (any number of panels) with lock rail and panel of BWP commercial plywood or veneered particle board with commercial veneering on both faces , the size of rail and style as per IS 1003 (Part-1) kiln seasoned and pressure treated all as specified.

S&F of Factory Made Solid PVC flush door shutter with wood free EPS core, 28 to 30mm thick (stiles), with 5mm thick prelam PVC Sheet on the front face & 5mm plain colour PVC sheet on back face, supplying & fixing in frame at site, as per specification & drawing

S&F of brass door magic eye: as given specification material resin lens +zinc alloy,top diameter: 31.2mm, botom diameter approx 24mm, pipe diameter approx 16mm total length approx 50mm, inner height approx 36mm application 35 to 60mm thick viewing angle 200 degree of surrounding without opening the door unique design ultra clear view and superior finish, wide angle best in class lens for all round visibility the outsider cannot hide any ware, the back cover protects you from the outsider observing any movements inside easy to instal with inbuilt screw over a wide range of door thickness from 35 mm to 60mm etc required at site, complete as directed by Engr-in-charge

S&F in Sheet glass ordinary quality 3 mm thick and glazing with oil putty ang glazing clips in squares n. exc 0.50 sqm each pane, complete all as specified and directed.

S&F in Sheet glass ordinary quality, ground or obscured or frosted, on one side 3 mm thick and glazing with oil putty and glazing clips in squares n. exc 0.50 sqm each pane, complete all as specified and directed.

Supply and fix in repair SS wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or using metal nut and bolts, complete all as specified and directed.

S&F of butt hinges medium weight 100 mm cold rolled stainless steel. complete all as specified and directed.

S&F of barrel tower bolts of 150 mm long aluminium anodised, complete all as specified and directed.

S&F of aluminium alloy, anodised 250 mm long sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

S&F of 300 mm long mild steel ordinary rat tail rod paltren spring incl roller and roller plate complete. complete all as specified and directed.

S&F of 150 mm long aluminium handles , cast type, anodised complete all as specified and directed.

Supply and fix in repair hasp and staple of size 100 mm, aluminium anodised, including bolt to hinge plate and fixed with screws, complete all as specified and directed.

Taking down cement plaster on brick wall or concrete surfaces of ceilling etc incl racking out joints hacking for key scrubbing down with water etc, complete all as specified & directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces including fin facia in cm 1:4 finished even and smooth without using extra cement complete all as specified & directed on external surfaces .

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cm 1:6 finished even and smooth with out using extra cement complete all as specified & directed.

M & L for rendering 10 mm thick on concrete surfaces of ceiling in cement mortar 1:3, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for two coat plaster 35 mm thick (20 mm + 15 mm) on rough concrete surfaces of fin, facia, chhajja and similar article in cm 1:3 finished even and smooth without using extra cement in any height including necessary scaffolding complete all as specified & directed. Note :- Two coat plaster shall be carried out as mentioned in clause 14.18 of SSR-2009, Part-I, complete all as specified and directed.

M & L for two coat of synthetic enamel paint on new or previously untreated steel surfaces of any description, not otherwise described over 10cm width or girth including preparation of new surfaces, complete all as specified and directed.

M & L for preparation of wooden surfaces of any description exc 10 cm in girth and applying two coats of synthetic enamel paint over a coat of pink primer including preparation of old painted surfaces, complete all as specified and directed.

M & L for preparation of old steel surfaces of any description exc 10 cm in girth and applying a coat synthetic enamel paint, complete all as specified and directed.

M&L for washing, rubbing down and stopping of distempered and old painted surfaces and applying clear colle putty to make surface smooth including two coats of oil bound distampering for wall (any tint), complete all as specified and directed.

M&L for preparation of old plastered or unplastered surfaces and applying two coats of white wash on ceiling surfaces, complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and applying two coats of colour wash (any tint), complete all as specefied and directed. Note:- Repairs to plastered surfaces and applying putty to make good of disturbed surface is included in the quoted rates.

M&L for preparation of new plastered surfaces of wall and applying chalk whitening primer and two coats of oil bound distamper (any tint), complete all as directed and specified.

M&L for preparation of new plastered or unplastered surfaces of ceiling and applying two coats of white wash (any tint), wash complete all as directed and specified.

M & L for preparation new plastered surfaces of wall and applying two coats of colour wash (any tint), complete all as specified and directed.

S&F solid chromium plated heavy door chain (weight not less than 249grms) with brass screws to any type of door shutter and frame, complete all as specified and directed

Demolition of brick work or stone masonry built in cement mortar including all quoines arches,pillar etc but excluding ashlar facing , dressed stone work and precast concrete articles complete all as specified.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4, complete all as specified and directed.

M&L for Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 as in half bricks. complete all as specified and directed.

M&L for water proofing treatment by applying water proofing membrane APP (Atactic Polyprobhlene Polymer) modified membrane with non-woven polyster reinforcement/mat with thermal insulation of weight not less than 3.6 kg/sqm and thickness not less than 3 mm, laid by torch application method with overlap 100 mm on length side and 100 mm on the width side over bituminous primer 0.30 Kg/Sqm by the same manufacturer conforming to IS 3384-1986 finished with two coats of bituminous aluminium paint on top of membrane and complete all as specified and directed and including 20mm thick rendering in cement mortar 1:4 rendering to be finished even smooth using extra cement including mixed with liquid water proofing admixture @ 200 ml per bag of cement including taking down existing membrane /tar phelt/Cement plaster complete all as specified and directed.

Supply only liquid water proofing compound, complete all as specified and directed.

Dismantling of water tanks of capacity 250 to 500 ltr and removing to store, complete all as specified and directed.

Supplied and fixed Rotational moulded polyethlene water storage tanks of 500 ltrs capacity ISI marked (cylindrical vertical with closed threaded top cover) hoisted and fixed in position all as specified in SSR Part I including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old broken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

S&F of Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 15 mm-142 gms / 20 mm - 210 gms / 25 mm - 455 gms), complete all as specified and directed.

Taking down steel water tubing of 15 mm dia bore incl connection & removal to store, complete all as specified and directed.

Taking down steel water tubing of 20 mm dia bore incl connection & removal to store, complete all as specified and directed.

Re-Fixing only old steel water tubing of 15mm bore and connections in new or old position fixed to walls, ceilings and floors etc. including fittings as required, complete all as specified.

S&F of Mild steel GI tubing 15 mm bore medium weight with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

S&F of Mild steel GI tubing 20 mm bore medium weight with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

S&F in repair 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair steel Sink with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x 460 mm and bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in repair Plate rack made of stainless steel 1.00 mm thick of size 600 mm (ht) x 900mm (width) fixed to wall with and including nuts & bolts of suitable size for fixing in wall, complete all as specified and directed.

Supply and fix in repair 10 ltrs capacity PVC symphonic action type, flushing cistern, low level, white, with inlet,ball valve, float and handle including brackets, fush pipe of polyethylene of low or high density or PVC 32 mm dia, complete all as specified and directed.

Supply and fix in repair Vitreous China squatting pan orissa pattern size 580 x 440 mm white with integral foot rests including connection to trap and to flushing pipe, complete all as specified & directed.

S&F in repair vitreous China wash basin,ovel shape counter sunk type white or in matching colour of tiles ,size 550x450 mm excluding taps,but including 32 mm dia waste coupling chromium plated brass and PVC waste pipe 750 mm long( Minimum), chain and plug and porcelain stopper, brackets for fixing any size, including cutting for and pinning in ends or erecting stand as directed by Engineer-in- change fixed in repairs, complete all as specified and directed.

S&F of swan neck long type Pillar taps, cast copper alloy 15 mm bore (minimum weight 700 grams) , with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repairs.complete all as specified and directed.

S&F in repair PVC connection 15 mm dia with PTMT nuts of length 450 mm. complete all as specified and directed.

Supply and fix in repair long body bib taps (minimum weight 575 grams), cromium plated cast copper alloy crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed. complete all as specified and directed.

Supply and fix in repair chromium plated stop cock/angle valve (minimum weight 575 grams) cast copper alloy screwed down high pressure ,with crutch or butterfly handle screwed both ends for iron pipe or for union of 15 mm bore, complete all as spd & directed

S&F in repair stop valve chromium plated 15 mm bore fancy type with long shank and cup (concealed type) (minimum weight 600 grams) screwed down high pressure ,with crutch or butterfly handle screwed both ends for iron pipe or for union of 15 mm bore, complete all as spd & directed .

S&F in repair brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.

S & F in repair brass chromium plated shower rose 125 mm size, complete all as specified and directed.

S&F in repair shelf of PTMT fixed to wall with aluminium screw (min wt 300 gm), complete all as specified and directed.

S & F in repair curtain rod 25 mm dia of pre painted aluminium with fixing brackets, stops, rollers, knob etc complete all as directed.

Dismantling of cast iron,PVC or reinforced concrete soil waste and drain pipe, 50/75/100 mm dia, including jointed in cement mortar or lead and taking out of trenches, if required, complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75 mm bore, single socketed in any length with rubber ring joints fixed to walls(ISI marked), complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110 mm bore, single socketed in any length with rubber ring joints fixed to walls (ISI marked), complete all as specified and directed.

S&F in repair PVC (SWR) bends 110 mm bore any radius (ISI marked), complete all as specified and directed.

S&F in repair PVC (SWR) bends 75 mm bore any radius (ISI marked), complete all as specified and directed.

S&F in repair Salt-glazed stoneware gully traps of size 150 mm x 150 mm, square or round mouthed, type 'P', complete all as specified and directed.

S&F in repair PVC (SWR) junction single, (Single T) equal or unequal of 110 mm (ISI marked), complete all as specified and directed.

S&F in repair PVC (SWR) junction single,(Single T) equal or unequal of 75mm (ISI marked), complete all as specified and directed.

S&F in repair PVC (SWR) vent cowl 110mm (ISI marked), complete all as specified and directed.

S&F in repair PVC (SWR) vent cowl 75mm (ISI marked), complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not in otherwise specifically provide, complete all as specified and directed.

M & L for Providing precast reinforced cement concrete B-1 (using 20mm graded crushed stone aggregate) 1:2:4 as in landing, cover slabs and like, complete all as specified and as directed.

M & L for Mild steel TMT bars 8 mm dia and over, cut to length, bent to shape required including crancking, bending spirally for hooping columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia, complete all as specified and directed.

S&F in repair mild steel angle or Tee section as in supports for shelves /water cooler etc and similar articles conforming to Fe-290 Gde E-165, including imbeded in wall, complete all as specified and directed.

M & L for Rooting out trees, flora & fauna and foliage as grown on RCC roof surfaces and brick walls by cutting hole into slabs/walls for digging out roots and using chemical to burn deep rooted tree roots etc and including making good dirturb portion of wall/roof with cement concrete 1:2:4 type B -1, complete all as specified and directed.

S&F in 18mm thick ultra voilet printed PVC board (weight not less than 12 Kg/Sqm) duly edge bonded with 0.8mm thick PVC taping as in cupboard/kitchen cabinet shutters fitting complete all as specified and as directed by Engineer -in-Charge.

S&F in Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flap (when open) 30mm complete all as specified and directed

Dismantling of old asbestos cement ( corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and directed.

S&F in repair mild steel angle iron or hollow section fixed in wall for chowkhats with hold fast including welding,angle iron support for chajjas/slab or similar works complete as specified and directed by Engr-in-Charge.

M&L for Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws/type hooks as specified including dismantling of old sheets of any description complete all as specified and directed.

S&F in repair MS Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., including drilling for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, complete all as specified and directed.

Taking down carefully aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specified and directed.

M&L for Point wiring with two runs of 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable in and including PVC conduit concealed with pressed mild steel terminal boxes rectangular / square type of adequate size with thickness of 1.5 mm duly painted with a coat of red oxide primer with suitable thickness ISI marked plastic laminated sheet cover of adequate size for one light or one fan controlled by one switch including one run 1.5 Sqmm FRLS, PVC insulated and unsheathed multi stranded flexible copper conductor cable as earth wire (green colour) to common earth dolly complete all as specified and directed. Note: (a) Unit rate include for cutting chases for conduits and sinking of boxes and making good to wall, floors, etc. (b) On RCC roof ceiling PVC conduit shall be provided on surfaces for fan etc with proper fixing clips all as specified and directed.

All as per Srl item No 96 here in before but for 5 pin 5 amp socket outlet on independent board complete all as specified and directed.

All as per Srl item No 96 here in before but for 3 pin 5 amp socket outlet on independent board complete all as specified and directed.

All as per Srl item No 96 here in before but for call bell point complete all as specified and directed.

M&L for Point wiring with 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel sunkum boxes having thickness as specified 3mm bakalite laminated sheet for one 3 pin socket outlet 15 Amp on independent board including 2.5sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete, all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green)

M&L Switch piano flush type 5 Amp single pole one way, 240 V (ISI marked), complete all as specified.

M&L Switch piano flush type 15 Amp single pole one way, 240 V (ISI marked), complete all as specified.

M&L socket outlet combination 2 in 1 , 3 pin 5 Amp flush type 240 V all as specified & directed.

M&L socket outlet combination 2 in 1 , 3 pin 5 and 15 Amp flush type 230 V all as specified & directed.

M&L Lamp holder Polycarbonate type with back plate having matching colour to holder for angle/batten fittings complete all as specified and directed.

S&F bell 230 V, Single pole complete all as specified and directed.

S&F bell push flush type 240 V, complete all as specified and directed.

S&F for Ceiling rose, 3 phase/bakelite 65x50mm two or three therminals isolated body fixed on PVC round block, complete all as specified and directed.

M&L Stepped type electronic fan regulator 0 to 4/5 step , flush type, heavy duty with hum free snubber circuit complete all as specified.

M&L for providing/cutting the round/ square hole of required size in wall finishing the disturbed surfaces as per existing finishes complete all as specified and supply and fixing MS ventilating fans single phase, 230 V 300mm or 12" H.D EX Fan (900 RPM) complete and supply and grouting the ragged bolts in wall, fixing the frame on the exhaust side ( outer surface of the wall) and connecting with and including PVC insulated three core 1.5 Sqmm copper cable from ceiling rose to exhaust fan motor and writing MES No with black synthetic enamel paint 2.0 cm high complete all as specified and directed.

M & L LED bulkhead 10 watt connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm all as required complete all as specified and directed.

S&F LED smart lamp, B22 type, 14 Watt, complete all as specified and directed.

S&F LED mirror light fitting 2 feet long, 1 x 10 W including LED tube 2 feet long of same make having ballast, bipin holder, connector block etc. complete with all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 Sqmm 3 core complete all as specified and directed.

S&F energy saving decorative LED box type (4 feet), 230 V, light fitting extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver with all accessories prewired and including making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceiling rose/PVC connector to light fittings complete all as specified and directed.

S&F energy saving LED rod 20 Watt (4 feet), 230 V, 6500 K energy efficient tube light, complete all as specified and directed.

S&F in replacement sheet metal enclosure factory made (Double door) type IP-43 Protection. Isolated Neutral,Door earthing, cement spill protector, IK-08 complete, single pole and neutral, 240 volts, 50 Hz, 8 way with 200Amps rated copper bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

M&L MCB single pole 240 V any rating from 20 to 40 amps, with rupturing capacity 10 KA, including providing thimble for outgoing cables, complete all as specified and directed.

M&L MCB SPN 240 V any rating from 6 to 40 amps, with rupturing capacity 10 KA, including providing thimble for outgoing cables, complete all as specified and directed.

Supply and laying in replacement of existing unserviceable/ burnt submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 6 sqmm drawing into and including concealed PVC rigid non metallic conduit of 20mm dia , 1.8 mm wall thickness and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 6 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: (i) Two runs of 6 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 6 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 20mm dia , 1.8 mm wall thickness wiil be measured as a one unit. (ii) Proper colour coding is to be followed as per IS Specification. (iii) Test certificates of cables to be submitted before commencement of work/ claiming for payment. (iv) wiring shall be concealed/ on surface with rigid PVC conduit medium grade as per site requirement. (v) Electric Wiring test sheet before and after completion of wiring to be submitted before claiming payment

S&F in sheet metal enclosures distribution boards, double door three phase 415 V 4 ways vertical TPN DB for comprising three phase four wire copper bus bar of appropriate capacity, complete all as specified and directed and comprising of the following :- a) MCCB four pole 100 amps AC 415 Volts 25 KA=01 No as incoming and 12 nos. MCB SP 40 Amps, C series as outgoing. Note :- (i) The DB shall be VTPN series of Schneider Cat Part No:- A9HVD04L or equivalent in any of the make mentioned in list of product. (ii) The DB shall be flush fixed and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost. (iii) Connection of MCCBs/ MCBs with cable shall made through appropriate size pin/bottle type timble-properly crimped. (iv) All the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) Double continuous earth wire shall be provided for each three phase DB from earthing mains dolly. (vi) MCCBs and MCB should have a same make as of DB.

S & F bldg secuirty light fitting energy saving high efficiency LED street light fitting 25 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 32 mm dia bent to shape having length on less than 1.5 mtr fixing with clamp etc and making connections using cord flexible 3 core copper cable of size 23/ .0076 from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage. Notes :- (i) Contractor shall produce LM79 & LM 80 test report from OEM owned NABL accredited laboratory. (ii) Contractor shall give guarantee/ warranty of complete fitting/ fixture for minimum 2 years from the date of completion. (iii) Contractor shall conduct the inspection of company representative at site before installation of the material at no extra cost. (iv) Contractor shall arrange complete material at site for approval of GE before incorporation in the work. (v) Driver shall be IP 66 degree of protection potted seal type with inbuilt SPD and external SPD of capacity 10 KV to be provided in addition to inbuilt.

Supply laying jointing and testing LT XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sqmm 4 core complete all as specified and directed.

Excavation in trenches n.exc 1.50m wide and n.exc 1.50m in depth for foundation etc. and getting out in any type of soil, complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm, in any type of soil, complete all as specified and as directed.

Removing excavated material (soil) not exceeding 50m and deposition where dircted at a level not exceeding 1.50m above the starting point, all as specified and directed.

M & L Dry sand cushioning to UG cable 8 cm thick before laying and 15cm thick after laying complete all as specified and directed. Note:- 1.Dry fine sand of best available quality shall be used. 2.Punned thickness shall be made and paid.

M & L Sub class `B` bricks laid dry flat transversely along the length of cable with width equal to the length of bricks over sand cushioning as protection cover of cable laid, complete all as specified and directed.

Supply and fixing in replacement of GI tubing medium grade of 40 mm nominal bore of pipe in trenches/under roads/ under culverts/under paths/under floor/on walls /with pole in new position with screwed sockets joints, together with all tube fittings complete all as specified and directed .

Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to galvanized earh lead wire of size 4.0 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3 of SSR Part I, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI medium grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified. Note: The rate quoted include cost of 7.5 metre earthing wire with protection pipe.

Notes : The Schedule of Credit amount shall be deducted from the total of this schedule(BoQ) to arrive at Contract Sum.

JP AND CO.

M/s. G M Builders & Contractors

VIKRAM SINGH MANHAS

Abrol construction co

OMKAR SHARMA AND CO