PROVN OF TOILET CUM BATH ROOM BLOCK FOR EME BN AND SPECIAL REPAIRS TO BLDG No T 75 SAINIK GUEST ROOM DINING HALL AT LIKABALI MIL STN UNDER GE 872 EWS

Amount

B/R SERVICES/WORKS

Demolition Cement Concrete (Un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Demolition Brick Work or Pre-cast Concrete Block Masonry, built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., complete all as specified and as directed.

Dismantling Timber Scantlings 40 Sq Cm and Over in Section in Unframed Work, Seggregating Serviceable Timber Scantlings and keep in Safe Custody for Refixing, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) not exc. 1.50 Square Metre Each, complete all as specified and as directed.

Taking down Chowkat or Frame of any description (without Taking Off Shutter from the Frame) of any description, exc. 1.50 Square Metre but not exc. 4.00 Square Metre Each, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting of any gauge and thickness, Segregating the Serviceable Steel Sheeting, stacking properly at Sites and keep in Safe Custody for re-use, complete all as specified and as directed.

Dismantling Wall and Ceiling Boards (Fibre, Pulp, Insulation, etc.) or Insulation Boards/ Slabs/ Blankets of any descriptions including Cover Fillets, complete all as specified and as as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing) and removing debris, etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. etc. to a distance not exc. 100.00 Metre, complete all as specified and as directed.

Hacking/Taking out Broken Glass of any description from Wooden or Metal Frames, or Stone, Concrete or Brick surrounds of any thickness or size; Hacking out Old Putty or Removing Beads, etc., complete all as specified and as directed,

Taking up or down Steel Tubing 15mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Taking up or down Steel Tubing 20mm bore (dia) and Connections, segregating the Serviceable Pipes and Connections, stacking properly at Site(s) and keep in Safe Custody for re-use, complete all as specified and as directed.

Taking/ Lowering down Unserviceable Water Storage Tank of any description, exc. 250 Litre and not exc. 500 Litre Capacity after disconnecting all Water Pipe Line Connections, complete all as specified and as directed.

Surface Dressing not exc. 15 Cm deep and getting out in Soft/Loose soil, complete all as specified and as directed.

Excavation in Over Areas, not exc. 1.50 Metre in depth and getting out as in Soft/ Loose Soil, complete all as specified and as directed.

Excavation in Over Areas, exc. 1.50 Metre but not exc. 3.00 Metre in depth and getting out as in Soft/ Loose Soil, complete all as specified and as directed.

Excavation in Trenches not exc. 1.50 Metre wide and not exc. 1.50 Metre in depth for Foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes, etc. not exc. 10 Sqm on Plan and not exc. 1.50 Metre in depth and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering and Well Ramming in layers not exc. 25 Cm, in Soft/Loose Soil, complete all as specified and as directed.

Removing Excavated Materials (Soils) not exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the Starting Point, complete all as specified and as directed.

M&L Hardcore Broken Stone or Boulders, Gauge not exc. 63mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and well rammed to a True surface, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (20mm graded stone aggregate) in Surface Channels and Drains, etc. including necessary Formwork as ordered, complete all as specified and as directed. NOTE : Cost of Formwork will deem to be include in the Quoted Unit Rate.

M&L Extra for Forming Fair finished Drain or Channel for Inner Girth in Cement Concrete, using Extra Cement including Forms, Moulds, Stopped Ends, etc., complete all as specified and as directed.

M&L Cement Concrete 1:3:6 (20mm graded stone aggregate) in Bed Plates, Bed Block, Benching, Coping, Holdfasts, Kerb Stones, etc. including necessary Formwork and Weathering, slightly Rounded or Chamfered Angles and Throating, complete all as specified and as directed. NOTE : Cost of Formwork will deem to be include in the Quoted Unit Rate.

M&L Cement Concrete 1:2:4 (40mm graded aggregate) in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deem to be include in the Quoted Unit Rate.

M&L Cement Concrete 1:4:8 (40mm graded aggregate) in Foundations, Filling and Mass Concrete, etc. including necessary Formwork, complete all as specified and as directed. NOTE : Cost of Formwork will deem to be include in the Quoted Unit Rate.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Foundation including Rafts, Footing, Foundation Beams for Column Basement Slab, under Reamed Piles, complete all as specified and as directed. NOTE: Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Columns, Pillars, Piers, Posts and Struts, etc., complete all as specified and as directed. NOTE: Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Beams, Cantilevers, Bressumers, Lintels over 1.50 Metre Span, etc., complete all as specified and as directed. NOTE: Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Walls, Retaining Walls, Basement Walls, Ballast Walls and the like; any thickness; above Top of Footings including attached Pilaster and Buttresses, complete all as specified and as directed. NOTE: Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Reinforced Cement Concrete 1:2:4 (20mm graded stone aggregate) in Slabs supported on Walls, Beams and Columns in Floors, Roofs, Landings, Balconies, Canopies, Deck Slabs and in Shelves and the like, complete all as specified and as directed. NOTE: Reinforcement & Formwork will be Measured and Paid for separately under appropriate Items.

M&L Pre-cast Reinforced Cement Concrete 1:2:4 (20mm graded aggregate) in Landings, Cover Slabs (for Manholes, etc.), Chullah Hoods, Chajjas, Water Troughs, Mangers, Shelves and Similar Articles with Plain faces and setting in Cement Morter 1:4, complete all as specified and as directed. NOTE : Reinforcement will be Measured and Paid for separately under appro-priate Items.

M&L Formwork to Sides of Concrete Foundations, Footings, Bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of Foundation and Plinth Beams; and Similar Work; Vertical or to Batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides of Pillars, Posts, Struts, Piers, Columns & Stanchions, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Sides and Soffits of Floor or Roof Beams, Girders, Beam Haunchings, Bress-summers, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Faces of Walls, Retaining Walls, Abutments, Parapets and Similar Work including attached Pillasters, Buttresses, etc.; Vertical or to Batter, Flat, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Soffits of Suspended Slabs such as Roof Slabs, Floor Slabs, Landings and Similar Work; not exc. 200mm thick (Horizontal or Sloping), etc., Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Formwork to Edges of Concrete Flats, Treads, Breaks in Floors, Window Cills, Openings in Concrete Walls, Floor and Roofs not exc. 20 Cm Wide and Sides of RCC/ PCC Bands in Walls, Horizontal or Sloping and Similar Work, exc. 10 Ccm but not exc. 20 Cm Wide, Rough Finished surfaces of Concrete, complete all as specified and as directed.

M&L Factory Made Pre-cast Cement Concrete Block Masonry with Solid Blocks (300x200x200mm or 300x200x100mm in size, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregate), exc. 10 Cm in Width and Setting in Cement Mortar 1:6, complete all as specified and as directed.

M&L Factory Made Pre-cast Cement Concrete Block Masonry with Solid Blocks (300x200x100mm in size, having Compressive Strength of not less than 100 Kg/ Sq Cm (as per IS-2185) in Cement Concrete 1:3:6 (20mm graded stone aggregate), 10 Cm in Width and Setting in Cement Mortar 1:4, complete all as specified and as directed.

M&L Brick Work with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work Half Brick thick with Sub-Class ‘B’ Bricks (Old Size Bricks), Straight or Curved on Plan to any Radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 40mm thick in Damp Proof Courses to Horizontal or Vertical Surfaces including Use & Waste of Formwork and Applying evenly a coat of Blown type Bitumen @ 1.50 KG/SQM and blinding with Clean Dry Sand @ 0.05 CUM/SQM, complete all as specified and as directed.

M&L Cutting Holes in Brick Walls, not exc. Half Brick thick, built in Cement Mortar for inserting of Holdfasts, Lugs, etc. and Making Good to dismantled portion with Cement Concrete 1:2:4 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required) and adjoining Surfaces in Cement Mortar 1:4, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) in Scantling, Cleansawn, Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

M&L for Refixing only Second Class Hardwood (well seasoned) in Scantling (except Scantlings, Serviceable Timber Scantling obtained from BOQ Item No. 1.003 here-in-before), Timber fixed (Unframed work), fixing with Nails, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Plain, Solid, Straight, Chowkats and Frame, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue pinned at Joints, complete all as specified and as directed.

M&L Factory Made Plain Framed, Panelled Shutter 40mm thick (Two Panels) with Lock Rail and Panel of 9.0mm thick BWP. Commercial Ply or 12mm thick Veneered Particle Board with Commercial Veneering on both Faces, having size of Rail & Stile as per IS:1003 (Part I) of Second Class Hardwood (Kiln Seasoned and Chemically Pressure treated) and fitted to Chowkat, complete all as specified and as directed.

M&L Second Class Hardwood (well seasoned) Glazed & Skeleton Shutter 30mm thick, Open rebated and prepared to receive Glass, Gauze, etc. (Without Sash Bars), Edges of Framing plain, chamfered or rounded. fitted with cut and mitred Beads for securing glass, etc.; sizes of Members of Shutters as specified in SSR Part I, Section 8, Clause 8.24(a) and fitted to Chowkat, complete all as specified and as directed.

M&L Taking down Shutter of any description, not exc. 1.00 Square Metre Each and Refixing in the Same Opening including necessary Resecuring, or Easing & Adjusting, etc., complete all as specified and as directed.

M&L Taking down Shutter of any description, exc 1.00 Square Metre but not exc 2.00 Square Metre Each and Refixing in the Same Opening including necessary Resecuring, or Easing & Adjusting, etc., complete all as specified and as directed.

S&F Factory made Solid PVC Door Frame of size 50x47mm made out of 5.0mm thick Plain Colour (Ivory Shade) PVC Sheet reinforced with Mild Steel Square Tube and fixing in opening as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutter with Particle Board Core 28mm to 30mm thick (Stiles) with 2, 4 or 6 Raised Panel Design with 2.0mm thick Moulded PVC Sheet on the Front Face and 2.0mm Plain Colour PVC Sheet on Back Face, fitted in Frame at Site as per Specifications & Drawings, complete all as specified and as directed.

S&F Aluminium Barrel Tower Bolt of size 125mm long (as approved), Anodised, Extruded Section, complete all as specified and as directed.

S&F Aluminium Barrel Tower Bolt of size 150mm long (as approved), Anodised, Extruded Section, complete all as specified and as directed.

S&F Aluminium Alloy, Anodised, Sliding Door Bolt 250mm long (as approved) with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Aluminium Alloy, Anodised, Sliding Door Bolt 300mm long (as approved) with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of size 75mm (as approved), complete all as specified and as directed.

S&F Stainless Steel Butt Hinge of size 100mm (as approved), complete all as specified and as directed.

S&F Aluminium Handle of size 125mm (as approved), Anodised, Cast type, complete all as specified and as directed.

S&F Aluminium Handle of size 150mm (as approved), Anodised, Cast type, complete all as specified and as directed.

S&F Floor Door Stopper with Overall Length of Cover Plate 150mm of Aluminium Alloy Anodised Body and Tongue (as approved) with Hard Drawn Steel Spring, fixed in Floor and Fixed-in-repairs (06 No. only), complete all as specified and as directed.

S&F Mild Steel 300mm, Ordinary Rat Tail Rod pattern Springs including Roller and Roller Plate and Fixed-in-repairs (06 No. only), complete all as specified and as directed.

S&F Brass Polished Cupboard Knob 40mm dia, fixed with Nut, Screws and Washer and Fixed-in-repairs (10 No. only), complete all as specified and as directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, complete all as specified and as directed.

S&F Sheet Glass 3.0mm thick, Plain, Ordinary quality and Glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and as directed.

M&L TMT Bars 10mm dia and Over, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L TMT Bars 8mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia, complete all as specified and as directed.

M&L Mild Steel Round Bars 16mm dia in Rungs, Bends, Steps, etc, cut to length and bent to Shape as required, complete all as specified and as directed.

M&L Mild Steel Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes including Bolts, Hooks (Stay) for large Gates; Hook and Pintle Hinges: large Hasps and Staples; Hand Made Sliding Bolts; Clamps; Holdfasts (Flat Iron 25x3.0mm thick); Wall Ties and similar small Articles conforming to Fe-290 Gde-E-165, complete all as specified and as as directed.

M&L Rolled Mild Steel Sections in Main and Cross Beams, Hip & Jack Rafters, Purlins where connected to Common Rafters, Running Rails and Guides for Sliding Doors, conforming to Fe-410-W (Gde E-250), Quality 'A', fixed with Angle Cleats or other Connecting Plates, complete all as specified and as directed

M&L Refixing Galvanised Mild Steel Sheeting 0.80mm thick Plain (Serviceable Steel Sheets obtained from BOQ Item No. 1.006 here-in-before) in Ridges, Hips, Valley Gutters, etc., fixing with and including L-type or J-type Cranked Hook Bolts with Washer, etc., complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Corrugated Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

S&F Pre-painted Galvalume Aluminum Zinc Coating GI based Plain Steel Sheet 0.50mm thick Coloured, having Tensile Strength of 550 Mpa in Ridges/ Roof Covering, Cladding to Walls, fixed with Aluminum Self Tapping Screws and Aluminum Washers of suitable Size, complete all as specified and as directed.

M&L Exposed Suspended False Ceiling System having Snap Grid/ Frame Work of size 605x605mm with and including Hangers 4.0mm dia GI (upto 1200mm length) for adjusting Level, fixed to Roof Slabs by means of Ceilling Cleats made out of GI Flat 40x3.0mm in size, 60mm long and Expansion Hold Fasteners 12.5mm dia, 40mm long, complete all as specified and as directed.

S&F HSPC Non-Asbestos Fibre Cement Building Boards 4.0mm thick, Pre-primed, Self Embossed, Textured Designer Boards, Water Resistant, Termite Resistant, Fire Resistant for insulation, fixed or laid/ inserted to Snap Grid Frame Work with Screws, complete all as specified and as directed.

S&F Prelaminated Particle Board 25mm thick, Exterior grade, Prelaminated One Side with Decorative Choice Lamination and Other Side Balancing White Lami-nation, fixed with Screws to Timber Frame Work including Providing Decorative Beading on Partitions, Nobs, Drawers and Sliding Shutter with all Fittings and Fixed-in-repairs (5.00 Sqm only), complete all as specified and as directed.

M&L Sand (as approved) Filling under Floors or in Foundations including Watering and Consolidation in layers not exc. 150mm thick, complete all as specified and as directed.

S&F Polythene Film, Black, 150 Micron, laid in Floors, complete all as specified and as directed.

M&L Cement Concrete 1:4:8 (40mm graded stone aggregate) 75mm thick in Sub-base to Floors, etc., complete all as specified and as directed.

M&L Cement Concrete 1:2:4 (12.5mm graded stone aggregate) 25mm thick in Leveling Course for laying of Tiles, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Non-skid Ceramic Coloured Tiles 7.0mm-8.0mm thick (Rectangular/ Square), Area of Each Tile exc. 0.11 Sqm but not exc. 0.18 Sqm (1st quality as approved) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured/Designer Tiles 7.0mm-8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm (1st quality as appoved) in Floors, Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, laid over and including Cement Screed Bed 15mm thick in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Non-Skid Ceramic Coloured/Designer Tiles 7.0mm-8.0mm thick (Square/ Rectangular), Area of Each Tile exc. 0.18 Sqm but not exc. 0.38 Sqm (1st quality as appoved) in Vertical Surfaces i.e. Dado, Skirting, etc., set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Glazed Ceramic Coloured Tiles 350x250x7.0mm or 450x350x7.0mm thick, (1st quality as approved) in Vertical Surfaces i.e. Dado, Skirting, etc., Set in Neat Cement Slurry and Pointed in Coloured Cement to match the Tile, fixing over and including Cement Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Granite (of any type) Work 20mm thick, (Table Rubbed and Polished) in Steps, Jambs, Pillars, Window Cills, Cooking Platforms and like in Cement Mortar 1:4 including Pointing in White Cement 1:2, using Marble Dust with Admixture of Pigment to match with Shade of Granite, fixing over and including Cement Screed Bed 15mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Marble (Makrana Doogri) Work 18 to 20mm thick, (Table Rubbed and Polished) in Steps, Jambs, Pillars, Window Cills, Cooking Platforms and like in Cement Mortar 1:4 including Pointing in White Cement 1:2, using Marble Dust with Admixture of Pigment to match with Shade of Marble, fixing over and including Cement Screed Bed 15mm thick in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Cement Concrete 1:2:4 (40mm graded stone aggregate) 50mm thick in Sub-base to Chequred Tiles, etc., finished Concrete Surfaces Fair and Even, complete all as specified and as directed.

M&L Chequered Cement Concrete Coloured (Terracota Red or Yellow) Tiles 200x200x25mm thick, with Grey Cement and Pigment, Set and Jointed in Neat Cement Slurry in Floors and Pointed in Grey Cement, laid over and including 15mm thick Cement Screed Bed in Cement Mortar 1:6, complete all as specified and as directed. NOTE : Cost of Cement Screed Bed will deem to include in Quoted Unit Rate.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) 75mm thick in Plinth Protection, etc., Laid in Alternate Panels, finished Concrete Surfaces Even and Smoooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (Internal) 10mm thick in Cement Mortar 1:6 on Brick/ PCC Blocks or Concrete Works, finished Plastered Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Rendering (External)15mm thick on Brick/PCC Blocks or Concrete Works consisting in 2 layers, Backing/Under layer of 10mm thick in Cement Mortar 1:4 and Float/ Top layer 5.0mm thick in Cement Mortar 1:4 including mixing WPC to Float/ Top layer, finished Fair and Even, complete all as specified and as directed. NOTE : Water Proofing Compound (WPC) will be Measured and Paid saperately under appropriate Item,

Supply only Water Proofing Compound (as approved), conforming to IS:2645-2003, complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Three Coats of White Wash, complete all as specified and as directed.

M&L Preparing New Plastered Surfaces of Walls and applying Two Coats of Distemper Oil Emulsion (as approved Tint) over a Coat of Chalk Whitening (Priming Coat), complete all as specified and as directed.

M&L Preparing Surfaces by Complete Removal of Existing Surfaces Treatment on Walls, Applying a Layer of Wall Care Putty 3.0mm thick on Cleaned Surfaces including Cutting and Rubbing down to obtain a Even and Smooth Surface and Applying Two Coats of Distemper Oil Emulsion (as approved Tint), complete all as specified and as directed.

M&L Preparing Newly Plastered Surfaces of Walls and applying Two Coats of Cement Based Paint (of approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing Surfaces by Complete Removal of Existing Surfaces Treatment on Walls and applying Two Coats of Cement Based Paint (of approved Tint) over a coat of Alkali Resistant Priming Paint, complete all as specified and as directed.

M&L Preparing New Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Pink Primer, complete all as specified and as directed.

M&L Preparing Old Painted Wooden Surfaces of any description, over 10 Cm in Width or Girth and applying One Coat of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint), complete all as specified and as directed.

M&L Preparing Steel and Iron Surfaces of any descriptions, over exc. 10 Cm in Width or Girth and applying Two Coats of Synthetic Enamel Paint (1st quality/ grade Paint of approved Tint) over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing New or Previously Treated Surface of Wood and Wood based Materials of any description and girth and treated with Two Coats of Creosote Oil, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of Wood and Wood Based Materials, of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Backs of Chowkats, etc. Area tarred exc. 0.10 Sqm but not exc. 0.50 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

M&L Preparing previously Untreated Surfaces of any description and girth not otherwise described and treating with Tar or Coal Tar Black Paint to Holdfast or similar Small Items, Area tarred not exc. 0.10 Sqm Each including Sanding with Clean Sharp Sand after tarred, complete all as specified and as directed.

S&F Galvanised Steel Tubing 15mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

M&L Refixing Old Steel Tubing 15mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from BOQ Item No. 1.011 here-in-before) in new or old position (Walls, Floors, etc.) including cleaning both inner and outer surfaces of Pipes by using Wire Brush including provision of New GI Fittings/ Connections (as required at Sites), complete all as specified and as directed.

S&F Galvanised Steel Tubing 20mm bore (dia), medium grade, conforming to IS-1239 with all Fittings, fixed to Walls, Ceiling or laid in Floors, complete all as specified and as directed.

M&L Refixing Old Steel Tubing 20mm bore (dia) and Connections (Serviceable Pipes and Connections obtained from BOQ Item No. 1.012 here-in-before) in new or old position (Walls, Floors, etc.) including cleaning both inner and outer surfaces of Pipes by using Wire Brush including provision of New GI Fittings/ Connections (as required at Sites), complete all as specified and as directed.

M&L for Laying CPVC Pipes 16mm (Outer Dia) and Fittings on Walls/ Ceiling or laying on Floors, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia), Cast Copper alloy, Chromium plated, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs (02 No. only), complete all as specified and as directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper alloy, Chromium plated, with Capstan Heads, screwed down, high pressure, with or without lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and Fixed-in-repairs (01 No. only), complete all as specified and as directed.

S&F Stop Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, screwed down, high pressure, with Crutch or Butter-fly Handle, screwed both Ends for Iron Pipe or for Unions, complete all as specified and as directed.

S&F Stop Valve 15mm bore (dia), Cast Copper alloy, Chromium Plated, Fancy type, with Long Shank and Cup Concealed, screwed down, high pressure, with Crutch or Butter-fly handle, screwed both Ends for Iron Pipe or for Unions and Fixed-in-repairs (02 No. only), complete all as specified and as directed.

S&F Gun Metal Globe/Gate Valve 20mm bore (dia) with Iron Wheel Head, screwed both Ends for Iron Pipe and Fixed-in-repairs (01 No. only), complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 500 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule, complete all as specified and as directed.

M&L Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS:12701-1996, hoisted and fixed in Position all as specified in MES Schedule, complete all as specified and as directed.

S&F PTMT Ball Valve 15mm bore (dia) having weight not less than 142 Grams, high pressure with Epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and Fixed-in-repairs (01 No. only), complete all as specified and as directed.

M&L Vitreous China White Squatting Pan of size 630x450mm, Orissa Pattern with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzles of WC Pan) including Provision of Lime Concrete Bedding and Making Good to Floor/ Distrubed Surfaces, complete all as specified and as directed.

S&F Vitreous China White Wash Down Water Closet Pan (Pedestal Pattern) with PVC (SWR) ‘P’ or ‘S’ Trap and Fixing Bolts and Making Good to Floor/ Distrubed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F White Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Device, complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity White, Low Level, Valveless, Syphonic Action type with Inlet, Ball Valve, Float and Handle, and PVC Flush Pipe 32mm bore (dia), a pair of Cast Iron Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3, complete all as specified and as directed.

S&F Vitreous China White Urinal, Full Stall type with PTMT Urinal Spreader 15mm in Size (excluding Flushing Cistern, Flush Pipe & Waste Pipe), complete including Providing and fixing Plugs, Bedding Urinals against Wall in Cement Mortar 1:2, securing Urinal to Plug with and including 60mm long Brass Chromium plated Screws, Pointing around Urinal back in Cement Mortar 1:3, fixing Urinal Spreder of Brass Chromium plated, Flush Pipe, Grating and Union for Discharge Pipe (but Exclusive of fixing Supply Pipe to Flushing Cistern, Trap and Waste Pipe), complete all as specified and as directed.

S&F Vitreous China White Wash Hand Basin of Size 550x400mm in Oval Shape including Brass Chromium Plated Waste Fitting 32mm bore (dia) and PVC Waste Pipe 32mm bore (dia) of suitable Length including a Pair of Cast Iron Brackets Brackets Erecting Stand duly painted including cutting and pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and Fixed-in-repairs (01 No. only), complete all as specified and as directed.

S&F Brass Chromium plated Bottle Traps 32mm bore (dia) suitable for Wash Hand Basins with Inlet and Outlet, screwed for Pipe or Connections including necessary Packing, Union, Cap, etc. and Fixed-in-repairs (01 No.), complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in size and 450mm in length with PTMT Nuts and Fixed-in-repairs (02 No. only), complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in size and 600mm in length with PTMT Nuts, complete all as specified and as directed.

S&F Chromium Plated Shower Rose with Shower Arm 125mm, Swival Joint including fixing to GI Pipe 15mm bore (dia), complete all as specified and as directed.

S&F Stainless Steel Soap Dish/ Tray, not less than 150mm in size (as approved), fixing to Walls with and including Chromium plated Brass Screws and Wooden/ Plastic Cleats, complete all as specified and as directed.

S&F Tubular Towel Rail 20mm dia, Brass Chromium Plated, D-type, 60 Cm long between Flanges with Bracket (One Pair), fixed on Wall with Wooden/ PVC Cleats and Brass Chromoum Plated Screws and fixed-in-repairs (01 No. only), complete all as specified and as directed.

S&F Cast Iron Floor/Nahani Trap having Outlet Diameter of 50mm with Grating including Jointing to Waste Pipe fixed in Cement Concrete 1:2:4 (20mm graded stone aggregate), complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, fixed to Walls or in Floors and fixed-in-reapairs (1.00 RM only), complete all as specified and as directed.

S&F PVC (SWR) Bend 75mm bore (dia), any radius with Access Door, etc. and jointing with Solvent Cement and fixed-in-reapairs (02 No. only), complete all as specified and as directed.

S&F PVC (SWR) Vent Cowl of Size 75mm, Jointed with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) Vent Cowl of Size 110mm, Jointed with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) 110mm bore (dia) Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches, complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid for separately under appropriate Items.

M&L Cement Concrete 1:3:6 (40mm graded stone aggregate) in Concrete Bed to PVC (SWR) 110mm bore (dia) including Packing Under and Haunching against the Sides of Pipes after they are laid and tested; complete all as specified and as directed. NOTE : Necessary Earth Works will be Measured and Paid for separately under appropriate Items.

M&L Cutting into existing Manholes for Connecting PVC (SWR) Pipe 110mm bore (dia), Making Good to Pipe and Rendering, Cutting out existing Benching for and forming Branch Channel (½ Round or ¾ Section) in Cement Concrete 1:2:4 (20mm graded stone aggregate), Smooth Finished and Reforming Benching as required, complete all as specified and as directed.

M&L Cutting for Removing existing Branch Drain Pipe 150mm bore (dia), Making Good to Walling and Rendering, Cutting out Branch Channel and Making Good Benchings in Cement Concrete 1:2:4 (20mm graded stone aggregate), Smooth Finished and Reforming Benching as required, complete all as specified and as directed.

E/M SERVICES/WORKS

M&L Taking down carefully Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) complete from in any Position including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets but excluding Light Fittings of any description, Making Good Disturbed Surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including Providing Surface Treatment (White/ Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Taking down unserviceable Sub-main Wiring from Batten/ Conduit/ PVC Casing Capping of any description, Making Good disturbed surfaces of Walls/ Ceillings, etc. in Cement Mortar 1:3 including Providing Surface Treatment (White/Colour Washing, Distempering, Painting, etc.) wherever required to match the Existing Finishes, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated unsheathed multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated, unsheathed, multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Mmarked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/ FAN/ BELL POINT controlled by One 1-way Switch 6 Amp, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated unsheathed multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated unsheathed, multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire for ONE 3/5 PIN SOCKET 6 AMP POINT on SAME BOARD, complete all as specified and as directed.

M&L Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated unsheathed, multi-stranded single core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated unsheathed, multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Point Wiring with 2.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated unsheathed, multi-stranded single core Copper Conductor Cable with 2.5 Sqmm (nominal area) 1100 Volt grade FRLSH PVC insulated unsheathed, multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn in and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc. complete with PVC Board of suitable size for accommodating Switches, Sockets, Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE 3/5 PIN SOCKET OUTLET 6/16 AMP POINT on INDEPENDENT BOARD, complete all as specified and as directed.

M&L Sub-main Wiring with 2-Runs of 6.0 Sqmm (nominal area) 1100 Volt FRLSH PVC insulated unsheathed, multi-stranded Single Core Copper Conductor Cable and 1-Run of 4.0 Sqmm (nominal area) 1100 Volt FRLSH PVC insulated unsheathed, multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuty Conductor drawn through and including PVC Casing Capping (ISI Marked) of suitable size (approx 25/32/40mm width) along with all Fitting/ Fixtures as Tee, Bend, Elbow, Socket, Saddles, etc., complete all as specified and as directed. NOTE :- (a) Cost of 3-Run of Cable & 1-Run of PVC Casing Capping will deem to be include in the Quoted Unit Rate and the same will be Mesured as ONE UNIT. (b) Sub-main Wiring will be measured PVC Conduit only. Wires required for looping, etc. as ordered will deem to be include in the Quoted Unit Rate.

S&F PVC Rectangular Block of size 100x100x50mm deep with 3.0mm thick Plastic Laminated Sheet Cover for mounting Swiches, Sockets, Fan Regulators, etc. including Taking down/ out Unserviceable PVC Block (01 No. only), complete all as specified and as directed.

S&F Switch Piano 6 Amp, Single Pole, Flush type, 1-way, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Switch Piano 25 No. only catered under Schedule of Credit.

S&F Socket Outlet 6 Amp, 3 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Socket Outlet 01 No. only catered under Schedule of Credit.

S&F Switch Socket Combination 6 Amp, 5 Pin, 2-in-1, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Switch Socket Combination 03 No. only catered under Schedule of Credit.

S&F Switch Socket Combination 6/16 Amp, 3 Pin, 2-in-1, Multi Plug, Flush type, 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Switch Socket Combination 02 No. only catered under Schedule of Credit.

S&F Lamp Holder PVC/ Polycarbonate type with Back Plate suitable for Batten Fitting and connecting up, complete all as specified and as directed. NOTE : Unserviceable Lamp Holder 03 No. only catered under Schedule of Credit.

S&F Ceiling Rose 65x50mm, 3 Terminals, Surface Bakelite suitable for 230 Volt AC and connecting up, complete all as specified and as directed. NOTE : Unserviceable Ceiling Rose 17 No. only catered under Schedule of Credit.

S&F Ceiling Fan Regulator, Dimmer Switch type, 230 Volt AC, Rotary Stepped Electronic, 120/280 Volt including necessary Connection and connecting up, complete all as specified and as directed. NOTE : Unserviceable Fan Regulator 02 No. only catered under Schedule of Credit.

S&F LED Bulk Head e-TATRA Series Light Fitting 1x6.0 Watt having Plastic Housing with Clear Prismatic Diffuser LED 6.0 Watt Lamp and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable including Taking down unserviceable Light Fitting of any description (04 No. only), complete all as specified and as directed. MAKE : C&S E-TARTA Series 6W or equivalent Model in Make : BAJAJ/ CG/ HAVELLS/ PHILIPS (as approved by GE).

S&F Decorative Wall Light Fixture, made of Polycarbonate, suitable for 10 Watt LED Bulb and connecting up including Taking down unserviceable Lamp of any description (04 No. only), complete all as specified and as directed. MAKE : BAJAJ/ CG/ C&S/ HAVELLS/ PHILIPS (as approved by GE).

S&F Octane LED Panel Square 18 Watt with Light Source LED 18 Watt and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable including Taking down unserviceable Light Fitting of any description (10 No. only), complete all as specified and as directed. MAKE : HAVELLS, Model : Octane LED Panel Square 18W or equivalent Model in Make : BAJAJ/ CG/ C&S/ PHILIPS (as approved by GE).

S&F LED Integrated Batten T-5 Tube Light Fitting 1x20 Watt with LED 20 Watt and connecting up with and including suitable size Twisted Flexible Copper Conductor Cable including Taking down unserviceable Light Fitting of any description (10 No. only), complete all as specified and as directed. MAKE : HAVELLS E-LITE PRIDE PLUS 20W or equivalent Model in Make : BAJAJ/ CG/ C&S/ PHILIPS (as approved by GE).

M&L Taking down Ceiling Fan of any Make/Model/Sweep from any Height after disconnecting Electric Connection and Keep in Safe Custody for Re-hanging/ Re-fixing and Repairing, complete all as specified and as directed.

M&L Hanging/Fixing only Ceiling Fan (obtained from Item No. 2.020 here-in-before), connecting with and including suitable size Copper Conductor Cable from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

M&L Cutting Holes in Brick or Pre-cast Concrete Block Masonary Walls of suitable size for fixing Exhaust Fan and Making Good to Dismantled Portion with Cement Concrete 1:2:4 (20mm graded stone aggregate) or Cement Mortar 1:3 (as required), complete all as specified and as directed.

S&F Exhaust Fan 300mm Sweep with Louvers, Heavy duty, Single Phase, 230/240 Volt, AC supply, complete with all Accessories, connecting with and including suitable size Copper Conductor Cable from Ceiling Rose to Connector of the Fan, complete all as specified and as directed.

Supply & Installation Water Heater (Geyser) Storage type of 25 LITRE Capacity, BEE 5 Star rated, fixing to Walls, etc., and Providing necessary Connections and Testing, complete all as specified and as directed.

S&F MCB Single Pole 6 Amp to 32 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB (06 No. only), complete all as specified and as directed.

S&F MCB Single Pole & Neutral 40 Amp, 'C' Series, 50 Hz, 10 kA, 240 Volt and connecting up including Taking down/out unserviceable MCB (01 No. only), complete all as specified and as directed.

S&F Sheet Metal Enclosure, MCB Distribution Board 8-way, SPN, 240 Volt, Single Door, Front Openable, fixed Flush with Wall inside the Nitches or Outside on Wall Surface suitable for mounting Isolators & MCBs, suitable for Bus-bar 200 Amp rated capacity and connecting up including Taking down/out unserviceable MCB DB Sheet Metal Enclosure (01 No. only) of any description, complete all as specified and as directed. MAKE : HAVELLS, Cat No. DHDPSHOSRW08 or equivalent in Model in Make : LEGRAND/ L&T/ SCHNEIDER (as approved by GE)

Supply & Laying or Passing through Pipe 1100 Volt grade heavy duty, Cross-sectional area 10 Sqmm, 2 Core, Flat or Circular Cable with PVC insulated Aluminium Conductor served with an inner sheathing of PVC Tape armoured with Galvanised Steel Wire or Tape and Overall PVC sheathed in Service Connection suspended by insulating Hangers not more than 1.0 Metre apart including 4.0mm Suspension Wire including Taking down/ out Unserviceable Service Connection (70.00 RM only) of any description, complete all as specified and as directed.

M&L Earthing with Galvanised Earth Plate Electrode 600x600x6.0mm thick, buried directly in Ground vertically to a depth not less than 2.25 Metre below Ground Level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal Ground Level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) Light grade, connected to Test Point upto 7.50 Metre away from Earth Electrode situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc.150mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded stone aggregate) and Pre-cast RCC Cover Slab of size 350x350x50mm in Cement Concrete 1:2:4 (20mm graded stone aggregate), reinforced with 10mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, PGI Funnel with GI Watering Pipe 20mm bore (dia) Medium grade including necessary Excavation in Soft/ Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing including Taking down/out unserviceable Earthing of any description (01 Set only), complete all as specified and as directed.

Excavating in Trenches, not exc. 1.50 Metre Wide and Depth not exc. 1.50 Metre for Taking out/up and Laying of Cable Line, Water Pipe Line, etc., Forming Surfaces to required Foundation, etc. and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in including Spreading, Levelling, Watering, Well Ramming in Layers not exc. 25 Cm, Providing Heaps along the Route of the Cable Line, Water Pipe Line, etc. with Surplus Soil in Soft/Loose Soil, complete all as specified and as directed.

Supply & Laying PP-R (Polypropylene Random Copolymer) 3 layer Pipe SDR 7.4 (PN 16) and Fittings 32mm bore (dia) having Inner with Anti-microbial Property and Outer Green Coloured, UV Stabilize Property Fusion welded having Thermal Stability for Hot and Cold Water Supply including PP-R Plain and Brass Threaded Poypropylene Random Fittings and required for fixing to Walls or laid in Floor/ Ground and Testing of Joints as per Manufactures instruction, complete all as specified and as directed.

Supply & Laying PP-R (Polypropylene Random Copolymer) 3 layer Pipe SDR 7.4 (PN 16) and Fittings 63mm bore (dia) having Inner with Anti-microbial Property and Outer Green Coloured, UV Stabilize Property Fusion welded having Thermal Stability for Hot and Cold Water Supply including PP-R Plain and Brass Threaded Poypropylene Random Fittings and required for fixing to Walls or laid in Floor/ Ground and Testing of Joints as per Manufactures instruction, complete all as specified and as directed.

S&F PP-R (Polypropylene Random Copolymer) Gate Valve 32mm bore (dia), Brass insert with Wheel Head, screwed both Ends, complete all as specified and as directed.

M/s Sashi Enterprise

M/S Raju prasad