SPL REPAIRS TO BLDG NO T 80 AT INS SHIVAJI LONAVLA

Amount

M&L Roof tiles, Mangalore pattern,interlocking at side joints, laid dry in repair including replacement of broken tiles all as specified and as directed

Dismentling of battens for tiles, shingles etc of any size including tilting fillets spacers exc 15 cms

Dismantling of Plain or corrugated steel/AC sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings

Dismentling of o in fillets, rails, posts, rafters,purlins, etc. under 40 sq. cm in framed work section

Dismantling boarding, any description, fixed any position with nails

M&L Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc confirming to Fe-410W (Gde E-250) quality -A grade complete all as specified and directed

S &F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-410- W(Gde?E-250) quality-B

S &F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F MSA Flat wind ties for roof including securing bolts, posts and struts including all necessary drilling bolt or riveting etc and similar work confirming to FE-290 Gde E-165.

M&L for filleting section of fillet exc 25 but n.exc 50 sq cm in cement mortar 1;3 in any shape in cement mortar.

M&L Demolition of Unreinforced Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) all as specified and as directed.

Dismentling of Stone slabs and tiles of any description or thickness in floor aprons etc laid bedded and pointed in any mortor complete all as specified.

Dismantling floor, hearth or wall tilling including cement mortor bedding (but not backing), removing serviceble tiles to store and rubbish off the premises complte all as specified.

Demolition of Brickwork or stone/bou-lder masonry, built in Cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc.

M&L for Coloured Non Skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick screed bed in CM 1:6

M&l for Coloured Glazed ceramic tiles in vertical surface 350x 250x 7mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick backing coat cement plaster in CM 1:3 as specified and as directed

M&L Coloured Non - Skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm joint free, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick screed bed in CM 1:4

M&L for 18 to 20 mm thick Granite (of any type) work in single piece (table rubbed and polished) in steps, floors, window- cills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade over and including 10mm thick CM (1:4) bedding layer complete all as specified and as directed.

M&L for Brickwork with sub class 'B' bricks straight or curved on plan exc 6m mean radius, built in CM 1:6

M&L for half Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in in CM 1:4

M&L for Rendering 15 mm thick CM 1:6 on fair faces of brick work or concrete surfaces and to be finished even and smooth(without using extra lime or cement)

All as per item above but in cm 1:4 on external surfaces .

M&L 2 coats of distember oil emulsion on walls over 3mm thick wall care putty over Priming with alkali?resistant priming paint including preparing newly plastered surfaces

M&L for preparation of old surfaces of wall and applying two coats of oil bound distemper complete all as specified and as directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new/old surfaces including removal of old paint and preparation of surface all as specified and as directed.

Dismantling of 100mm internal dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed

S&F PVC (SWR) pipes of dia 110mm bore single socketed in any length with rubber ring joints fixed to walls/in trenches.

S&F PVC (SWR) pipe of 75 mm bore in single socketed in any length with rubber ring joints fixed to walls..

S&F PVC (SWR) bends of 110 mm dia bore

S&F PVC(SWR) Vent cowl of 110mm dia bore.

M & L PVC Nahani trap 75mm size with grating including jointing to waste pipe fixed in cement concrete type type B1 (1:2:4)

S & F in repairs Vitreous China wash basin, white, flat back, size 630x450mm excluding ditto but including brackets, 32mm Waste fittings, brass, chromium plated with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed with fancy type pillar tap complete all as specified

S&F in repairs Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) white Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and seat cover complete in all respect all as specified all as specified

S&F Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc., overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm

S&F in repair Bib taps 15 mm dia, fancy type chromium plated screwed down, screwed for iron pipe or for brass ferrule and fixed for 15 mm dia pipe.

S&F in repair Stop valves 15 mm dia, fancy type chromium plated, screwed down, high pressure, screwed both ends for 15mm dia pipe or for unions fixed in repairs

S&F in repair PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified.

S&F in repair Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including shower arm, fixing to steel pipe or union all as specified and directed

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

M&L in repairs 40mm Rubber or vulcanite plugs (waste) with rings and fitting and fixing including chromium plated brass or bronze chain and stay (chain n exc 50 cm in length)

S&F Stainless steel soap dish, white of size 160X160X90 mm as approved fixed with brass screws or embedded in wall . Make : Cera Cat No. F5003106 or equivalent in other makes as specified

S&F in repair Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges

Taking up or down steel tubing of bore 15/20 mm and connection, including cleaning for refixing or removal complete all as specified.

Taking up or down steel tubing 25/32 mm and connection, including cleaning for refixing or removal to store complete all as specified.

S&F CPVC pipes, SDR 11, 20 mm outer dia of pressure rating 6 kgf/sqcm conforming to IS-15778 with all fittings such as Tee,Bends, elbows ,unions ,sockets and end pieces etc to receive fittings and fixed with solvents fixed to walls/ floors (Conceled where required) with all clamps in Shafts/ducts with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure

S&F CPVC pipes, SDR 11, 25 mm outer dia of pressure rating 6 kgf/sqcm conforming to IS-15778 with all fittings such as Tee,Bends, elbows ,unions ,sockets and end pieces etc to receive fittings and fixed with solvents fixed to walls/ floors (Conceled where required) with all clamps in Shafts/ducts with all necessary scaffolding to fix the pipes and testing the joints under prescribed pressure

S&F Harrison rails,anodised aluminium alloy, chromium plated with fixing brackets, stops, rollers etc

Taking down chowkats or frames N.exc 1.5 Sqm with shutter (without taking of shutter from the frame.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60(Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S&FProviding 30mm thick "RAJSHRI" BRAND FACTORY MADE WIRE MESH SOLID WPC DOOR SHUTTER consisting of Density 500 Kg /Cbm Manufactured by an ISO-9001-2015 certified Company , Door to be panelled with SS mosquito Mesh and XTN aluminium Mesh for additional strength and safety purpose. (confirming as per IS:4020). The door should be water proof, termite proof, fire retardant and having screw holding capacity. Door to be fixed to frame with 3 nos. M.S powder coated butt hinges size 100mm*25mm*2mm and 32mm long steel screws drilled suitable to pass through both the walls of the M.S tube.Other hardwares should be fixed with 19*6mm size steel screws etc. Complete as per direction of Engineer-in -charge, manufacturer's specification & drawings.

S & F 100 mm size Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, typeB-11

S&F Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed 150mm long.

S&F 200mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed

S&F 100mm Extruded brass handles, fabricated type polished

S&F 4mm thick Non Asbestos (E-Board) designer tiles of approved design suitably fixed in false ceiling grid/frame with staples or screws complete in repair all as specified and as directed.

S&F Powder coated aluminium snap grid frame work of size 605x605mm for false ceiling all as specified

Taking down steel/aluminium windows/ventilator of any size with all fittings complete

M&L for powder coated aluminium two track, two shutters (of equal width), sliding type windows without sash bars including necessary jointing clips, rubber packing, neoprene rubber gasket, aluminium snap beading, screws, aluminium fittings, handles, locking arrangement (star lock), bearings (two No's for each sliding shutters) with 4.00mm sheet glass for glazed including following powder coated sections as given in 'JINDAL' catalogue complete all as specified and as directed :- (i) Frame (Bottom) -20619 (ii) Frame (Top & Side)-20681 (iii) Shutter vertical (Handle lock)-20846. (iv) Shutter vertical (Int lock)-20845. (v) Shutter (Top)-20844. (vi) Shutter (Bottom)-20847. Note :-(i) The window opening shall be provided with four shutters of equal width.(ii) The shutters shall be placed in such a manner that at a time the entire width of window can be utilized as fully glazed window. (iii) The thickness of the powder coating shall not be less than 0.5 micron & the tint shall be as decided by GE.

S&F Aluminium powder coated ventilator partly fixed and partly louvered type without sash of bars, section as per designation 63400 of IS 737, frame and intermediate made out of aluminium section of size 50.80 x 25.40 x 0.95 mm (Catalogue No 14027 of M/s Jindal) including necessary heavy duty louvers (adjustable with locking arrangements), jointing clips, rubber packing, anodised snap beading, screws alongwith 4.00mm thick pin headed glass for louvers and glazing etc complete all as specified and as directed. Note:- The thickness of the powder coating shall not be less than 0.5 micron & the tint shall be as decided by GE.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer?in-charge

PCC (1:4:8) type D2 (using 40 mm graded stone aggtegate) as in foundation filling and mass concrete

M&L for coloured chequered cement concrete tiles 30cm X 30cm X 25mm thick set jointed & pointed in neat cement slurry with grey cement and pigments ove 20 mm thick screed bed in CM (1:6) complete all as specified

M&L Demolition and breaking up drain pipes 150mm (Salt glazed ware, AC or Reinforced concrete) set in cement mortar

M&L for Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil and getting out .

M & L for PCC 1:3:6 type C2 (using 40 mm graded aggregae in foundation and mass concrete.

M&L Cutting into existing manholes for connecting new drains, making good to 150mm internal dia of pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required

M& L for 200 mm dia. Reinforced concrete pipe, class NP -3, laid and jointed compete with collars.

M&L for concrete bed to 200 mm dia. Pipe,PCC 1:3:6, type D2( using 40mm graded aggregate. ) Including packing under , and hancuching against the sides of pipes after they are laid and tested.

M&L for PCC 1:2:4,type B-1(using 20mm graded aggregate.), in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, opings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

S&F Cast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers, stop valve boxes, gate stops, parts of ranges, balusters and similar articles

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated material exc. 250m and n exc 500m, depositing where directed at a level n exc. 1.5m above the starting point

Supply only water proofing compound

Taking down carefully unserviceable aluminium/copper point wiring (light, fan, socket or power) including unserviceable light fittings, switch board complete, switch sockets, ceiling roses, pendants, regulators, sockets, etc and removing materials from site and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

M & L for Point wiring with 1.5 Sqmm (nominal area), FRLS PVC insulated, multistranded, single core unsheathed, copper conductor cables passing through and including providing PVC casing caping with all fittings and accessories of PVC casing caping (like Tee, bend etc.) complete fixed to walls /ceiling etc. with and including 1.5 Sqmm (nominal area) FRLS PVC insulated, unsheathed, stranded, single core, copper cable green in colour as earth continuity wire connecting to common earth point including PVC terminal box fixed with suitable sizes cadmium plated iron screws and washers etc.for mounting switches, sockets, regulators etc complete for one light/fan/bell/buzzer point controlled by one ,one way switches complete all as specified and directed. (a) One light point or one fan point or bell point controlled by one switch

(b) One 3 pin socket outlet, 5 Amp independent

(c) One 3 pin socket outlet, 5 Amp on the same board with other switches

(d) One bell/buzzer point controlled by one push button on the same board with other switches or independent with cable 1.5 sq mm size.

All as per item No.79 here in before but wiring with cables of size 2.5 sqmm for wiring & cables of size 2.5 sqmm both (FRLS) as continuous earth wire for one 15 Amps, 3 pin Switch/Socket outlet on Independent board complete all as specified and directed. (Note : cutting chases & making good of disturbed surfaces shall be measured and paid separately).

S & F switch piano, 5 Amp, single pole, flush type one way 230 volts complete all as specified and as directed.

S & F socket out let, 2 in 1, 3 pin, 5 Amps, 240 volts complete all as specified and directed.

S & F Switch socket combination, 2 in 1, 5 Amps, flush type, 240 volts complete all as specified and directed.

S & F Switch socket combination, 5 in 1, 5/15 Amps, 240 volts, flush type complete all as specified and directed.

S & F switch bell push, flush type 5 Amp. Complete all as specified and directed

S & F Ceiling rose, 3 way PVC insulated body complete all as specified and directed by engineer in charge.

Supply and fixing Batten 1x18W(single side supply)for LED TUBE LIGHT pre -coated CRCAA sheett, end caps made up with engineering plastic all as specified and directed.Make : Bajaj (BLRB - DB 118) or equivlent PhilipsHavells.

Supply and fixing ROD 1x18W (single side supply)for LED TUBE LIGHT T8 tube with polycarbonate body all as specified and directed.Make : Bajaj (BLRB - 20W LED) or equivlent PhilipsHavells.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete. Make: Crompton or equivlent Bajaj/Philips/Havells

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.Make: Crompton or equivlent Bajaj/Philips/Havells

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC)

Supply and fix electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc. all as specified and directed.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20DP all as specified and directed

Taking down electric meter of any type and any make single/three phase by dismantling of all electrical connection checked the meter, and Refixed same Nos of meter on wooden board in metal box of suitable size in same Nos of quarter after repair works completed.

M&L for earthling complete with galvanized GI earth plate electrode of size 600x600x6.00 mm, buried directly in ground (earth pit not less than 2.25 mtr below normal ground level) with top edge of earth plate not less than 1.5 mtr below normal ground level connected to galvanized earth lead wire 4.0 mm dia by means of volts, nuts, check nut and galvanized iron or steel including earth work in any type of soil, charcoal salt 15 cm around the earth plate as shown in electrical plate No 3 of SSR part1991,20 mm dia watering pipe medium grade 1.50 mtr long GI protection pipe light grade 15 mm dia from earth pit to main board (NOTE:- maximum length of GI protection pipe with each earth shall not be less than 7.5 mtrs) including necessary pit with cover , including testing on complition.

S&F MCB DB TPN 4 ways double door with 440 Volt, 200 amps rated bus bar with all accessories flush in the wall including matching the existing surface all as specified and directed Make:Havells QVE series or equivlent legerend/standard/indoasian

S&F in replacemen MCB DB SPN 4 ways double door with 240 Volt, 200 amps rated bus bar with all accessories flush in the wall including matching the existing surface all as specified and directed.Make:Havells QVE series or equivlent legerend/standard/indoasian

M&L for sub main wiring drawing through PVC casing and capping with Wiring alongwith earth wire size 4x4.0 sq. mm +2x4 sq. mm earth wire earth wire of FRLS is PVC insulated copper conductor, single core cable in surface/recessed as required .Note:- Four run of 4 sqmm wire and Two run of 4 sqmm wire and One run of PVC casing caping will be measured as one running meter.

Supply lay and testing cable XLPE insulated screened beded,galvanized steel trip or wire armoured, electric power cables (heavy duty) 1100 Volt grade with stranded aluminium conductor of size 35 sq mm 3.5 core. Including taking down old unserviceable cable any size by dismantling of all electrical connection etc all as diercted.

S&F in repairs MCB SP 5 To 32 AMP, single pole 240 Volts 10KA ''C''&''B'' curve , as per site requirment,Complete all as specified and directed.

S&F in repairs MCB SPN 6-32 AMP, 240 Volts 10KA 'C' curve , Complete all as specified and directed.

Supply and fixing MCB TPN/FP 40 To 100 AMP 415V 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the DB complete with connection testing and commissioning.

KARPE AND SONS CONSTRUCTION (BID ID -3124425)

DWARKESH STRUCT-CON (BID ID -3120080)

seema enterprises (BID ID -3124572)

VIJAYA ENTERPRISES (BID ID -3123494)

United Engineers and Contractors (BID ID -3124574)