Loading…
Loading…
Tender Value
₹142.7 Cr
EMD Value
₹1.5 Cr
Closing Date
8 Jun 2026, 3:00 pm3d left
Shiv Shankar Prasad
Executive Engineer
EXECUTIVE ENGINEER, ROAD DIVISION, SITAMARHI
SUPERINTENDING ENGINEER, NORTH BIHAR ROAD CIRCLE MUZAFFARPUR
SE
LONG TERM OUTPUT AND PERFORMANCE BASED ROAD ASSETS MAINTENANCE CONTRACT OF ROADS UNDER ROAD DIVISION, SITAMARHI PACKAGE - 06B/OPRMC-III
132461
NIT No.- 01/2026-27 2/06B
Open Tender
CIVIL
Sitamarhi
• Registration
• Bid Security
(Bid Security can be paid through offline or online
mode)
• Cost of BOQ
• Bid Validity
• Conflict of Interest
• Bidder's Information Sheet
• Joint Venture Information Sheet
• Undertaking by the Joint Venture Partners
• Pending Litigation
• Historical Contract Non-Performance
• Net Profit
• Net Worth
• Annual Turnover
• Bid Capacity
• Financial Resources
• Exiating Committements of on-going Works
• General Experience
• Specific Experience
• Personnel
• Equipment
• Initial Tentative Program of Performance
• Project Specific Information
• Power of Attorney of Signatory of Bid.
• Affidavit
• PAN
• GSTIN
• Technical Bid Sheet fill and upload
• Any other if required as per Tender document
CIVIL
ITEM RATE
L1
1
28 documents required · 28 mandatory
₹10,000
Processing Fee: 5900
₹1.5 Cr
Office of Chief Engineer (North), RCD, Bihar, Patna
28 May 2026
28 May 2026
8 Jun 2026
29 May 2026
8 Jun 2026
29 May 2026
3 Jun 2026
Ordinary Maintenance Services in the following Roads (with chainage): -
Runnisaidpur-Belsand-Parsauni Road 0-8.76 KM
Sitamarhi-Riga-Dheng Road 0-22.755 KM
Riga-Majorganj Road 0-17.00 KM
Kushmari-Basantpatti Road 0-10.34 KM
Parsauni-Riga Road 0-15.00 KM
Majorganj-Dheng Road 0-10.90 KM
Sisaula- Akhta Road 0-4.564 KM
Narha-Dumri Road 0-9.05 KM
Belsand-Chhitauni Road 0-4.00 KM
Partapur-Gisara-Bari Bazar (Dumra) 0-18.00 KM
Kusumari to Khairwa Road 0-4.99 KM
Sisaula to Basantpatti 0-7.44 KM
Left over portion of NH-104/227 (New) Pamra to Mehsaul Chowk 0-10.10 KM
N.H. 77-Murliyachak Road 0-4.60 KM
Runnisaidpur-Belsand-Parsauni Road 13.04-21.80 KM
Phulwariya Ghat to Bahar village 0-24.05 KM
Bahar village to Kanhauli 0-10.925 KM
Item No.
In words
Repairs to shoulders /Construction of Earthen shoulders on both sides of the carriageway wherever required to bring the service level (with 3% camber) (i) Earthen Shoulder: (a) High Shoulder (b) Low shoulder (ii) Hard Shoulder: (a) Paved Shoulder/ Granular (b) Footpath
Plantation in medians and islands not maintained by other agencies.
Pruning of trees to get 5.5 m height above the pavement.
Repairs and cleaning to Cross Drainage Works including Culverts and side drains (outside the area of Municipal Corporation and Nagar Parishad) to specified service levels by taking up required items ensuring to minimum quantity as per Section 5D of Technical Specification.
Providing Road safety and informatory items complete as per IRC:67 latest code specifications such as;
Providing and fixing new mandatory, cautionary and informatory Retro Reflectorized signage, ensuring minimum quantity as per Section 5D of Technical Specification.
Maintenance of existing signages ensuring minimum quantity as per Section 5D of Technical Specification.
Fixing new and maintenance of existing KM stones as per MORTH Specifications ensuring minimum quantity as per Section 5D of Technical Specification.
Fixing New & Maintenance of existing Guard stones/ Guide post as per MORTH Specifications ensuring minimum quantity as per Section 5D of Technical Specification.
Fixing New and Maintenance of existing Object Hazard Marker at the opening ends of culverts and bridges or at any other points, delineators. median markers and bollards (spring post) as required, as per MORTH Specifications ensuring minimum quantity as per Section 5D of Technical Specification.
Providing New and Maintenance of existing Rumble strips/ speed breaker or any traffic calming measures on minor/major roads as per MORTH Specifications ensuring minimum quantity as per Section 5D of Technical Specification.
Providing new and maintenance of existing Road marking as per IRC: 35/latest code-
Hot Applied Thermoplastic compound 2.5mm thick including reflectorising glass beads with (Clause 803-Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface-Providing & laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @250gm/sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35 latest code. The finished surface to be level, uniform & free from streaks & holes). i. Centre line, lane line marking as per IRC: 35 latest code or as per existing road markings. ii. Edge line marking for all lanes/ roads as per IRC:35 latest code or as per existing road markings. Ensuring minimum quantity as per Section 5D of Technical Specification.
For Urban roads as mentioned in Appendix and as per the direction of Engineer-in-charge: Providing & fixing of reflective pavement markers (Road studs (Road Markers/Road Stud with micro prismatic Lense Reflector- Providing & fixing of road stud 100x100mm, die-cast moulded from ASA (Acrylic Strene Acrylonitrite) High impact poly styrene or ABS (Acrylonitrile Butadiene Styrene) body resistant to minimum support a load of 13635 Kg and Fitted with micro prismatic Lence Reflector installed in concrete or asphaltic surface by drilling hole 30mm upto a depth of 60mm and bedded in a suitable bituminous grout or epoxy mortar, all as per MORTH Specifications ensuring minimum quantity as per Section 5D of Technical Specification.
Repair and Painting of road side assets including painting of trees & poles on formation width; (a) Repair of dividers, road kerbs, islands, parapets and RCC/Brick drains (b) Painting of Trees and Poles Painting of road divider, island, parapets, kerbs etc. ensuring minimum quantity as per Section 5D of Technical Specification.
Any additional activities the Bidder considers necessary to achieve the Service Level Objective.
Item No.
In words
Tack Coat (Clause-503) - Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom
BC 30mm (Clause 507) - Providing and laying Bituminous Concrete with 100-120 TPH batch type Hot Mix Plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification (5th revision) Clause No. 507 complete in all respects.
Maintenance of Shoulders as per MORTH Specification 305.
Thermoplastic Edge Line Marking.
Painting of Parapets, Kerbs, Islands, Dividers.
Cats Eye
Single lane (Carriage way width < 3.75m) (30 mm thick BC). Rate shall be quoted assuming per kilometre carpet area as 3750m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Intermediate lane (30 mm thick BC) (Carriage way width > 3.75 and < 7.0 m). Rate shall be quoted assuming per kilometre carpet area as 5500 m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Providing 40mm thick BC for Periodical Maintenance to Double and Multi lanes including profile correction (Carriage width ≥ 7.0m) with the following items of work to obtain the required service level.
Tack Coat (Clause-503) - Providing and applying Tack Coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/ granular surface cleaned with mechanical broom.
BC (Clause-507) - Providing and laying Bituminous Concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification (5th revision) Clause No. 507 complete in all respects.
Providing shoulder width 2.5m using with 3% camber to the required the service level for low shoulders as per MORTH Specification Clause 305.
Providing centre line and lane line marking (Hot Applied Thermoplastic compound 2.5 mm thick including reflect rising glass beads) as per IRC:35/latest code.
Providing Continuous edge line marking (Hot Applied Thermoplastic compound 2.5mm thick including reflect rising glass beads) as per IRC:35/latest code.
For Urban & Rural Roads as mentioned in Appendix and as per the direction of Engineer-in-Charge - Providing & fixing of reflective pavement markers Road Markers/Road Studs with micro prismatic Lense Reflector- Providing and fixing of road stud 100 x 100 mm, die-cast moulded from ASA (Acrylic Strene Acrylonitrite) High impact poly styrene or ABS (Acrylonitrile Butadiene Styrene).
Providing repairs & painting to median & kerbs, islands, dividers.
Maintenance of shoulders as per MORTH Specifications- 305.
Double Lane - Rate shall be quoted assuming per kilometre carpet area as 7000m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Double Lane with Paved Shoulders of width ______________.
Providing Periodic Maintenance to Single and Intermediate Lanes including profile correction with the following items of works to obtain the required service level.
Tack Coat (Clause-503) - Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom
BC 30mm (Clause 519) – Recycling pavement by cold milling of existing bituminous layers, planning the surface after cold milling, reclaiming excavated material to the extent of 30 percent of the required quantity, hauling and stock piling the reclaimed material near the central recycling plant after carrying out necessary checks and evaluation, adding fresh material including rejuvenators as required, mixing in a hot mix plant, transporting and laying at site and compacting to the required the grade, level and the thickness, all as specified in clause 519.
Maintenance of Shoulders as per MORTH Specification 305.
Thermoplastic Edge Line Marking.
Painting of Parapets, Kerbs, Islands, Dividers.
Cats Eye
Single lane (Carriage way width < 3.75m) (30 mm thick BC). Rate shall be quoted assuming per kilometre carpet area as 3750m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Intermediate lane (30 mm thick BC) (Carriage way width > 3.75 and < 7.0 m). Rate shall be quoted assuming per kilometre carpet area as 5500 m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Providing 40mm thick BC for Periodical Maintenance to Double and Multi lanes including profile correction (Carriage width ≥ 7.0m) with the following items of work to obtain the required service level.
Tack Coat (Clause-503) - Providing and applying Tack Coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/ granular surface cleaned with mechanical broom.
BC (Clause-519) – Recycling pavement by cold milling of existing bituminous layers, planning the surface after cold milling, reclaiming excavated material to the extent of 30 percent of the required quantity, hauling and stock piling the reclaimed material near the central recycling plant after carrying out necessary checks and evaluation, adding fresh material including rejuvenators as required, mixing in a hot mix plant, transporting and laying at site and compacting to the required the grade, level and the thickness, all as specified in clause 519.
Providing shoulder width 2.5m using with 3% camber to the required the service level for low shoulders as per MORTH Specification Clause 305.
Providing centre line and lane line marking (Hot Applied Thermoplastic compound 2.5 mm thick including reflect rising glass beads) as per IRC:35/latest code.
Providing Continuous edge line marking (Hot Applied Thermoplastic compound 2.5mm thick including reflect rising glass beads) as per IRC:35/latest code.
For Urban Roads & Rural as mentioned in Appendix and as per the direction of Engineer-in-Charge - Providing & fixing of reflective pavement markers Road Markers/Road Studs with micro prismatic Lense Reflector- Providing and fixing of road stud 100 x 100 mm, die-cast moulded from ASA (Acrylic Strene Acrylonitrite) High impact poly styrene or ABS (Acrylonitrile Butadiene Styrene).
Providing repairs & painting to median & kerbs, islands, dividers.
Maintenance of shoulders as per MORTH Specifications- 305.
Double Lane - Rate shall be quoted assuming per kilometre carpet area as 7000m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Double Lane with Paved Shoulders of width ______________.
Providing Periodic Maintenance to Single and Intermediate Lanes including profile correction with the following items of works to obtain the required service level.
Tack Coat (Clause-503) - Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom
BC 30mm (Clause 518) – Providing laying and rolling of bituminous cold mix on prepared base consisting of a mixture of unheated mineral aggregate and emulsified or cutback bitumen, including mixing in a plant of suitable type and capacity, transporting, laying compacting and finishing to specified grades and levels.
Maintenance of Shoulders as per MORTH Specification 305.
Thermoplastic Edge Line Marking.
Painting of Parapets, Kerbs, Islands, Dividers.
Cats Eye
Single lane (Carriage way width < 3.75m) (30 mm thick BC). Rate shall be quoted assuming per kilometre carpet area as 3750m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Intermediate lane (30 mm thick BC) (Carriage way width > 3.75 and < 7.0 m). Rate shall be quoted assuming per kilometre carpet area as 5500 m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Providing 40mm thick BC for Periodical Maintenance to Double and Multi lanes including profile correction (Carriage width ≥ 7.0m) with the following items of work to obtain the required service level.
Tack Coat (Clause-503) - Providing and applying Tack Coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/ granular surface cleaned with mechanical broom.
BC 30mm (Clause 518) – Providing laying and rolling of bituminous cold mix on prepared base consisting of a mixture of unheated mineral aggregate and emulsified or cutback bitumen, including mixing in a plant of suitable type and capacity, transporting, laying compacting and finishing to specified grades and levels.
Providing shoulder width 2.5m using with 3% camber to the required the service level for low shoulders as per MORTH Specification Clause 305.
Providing centre line and lane line marking (Hot Applied Thermoplastic compound 2.5 mm thick including reflect rising glass beads) as per IRC:35/latest code.
Providing Continuous edge line marking (Hot Applied Thermoplastic compound 2.5mm thick including reflect rising glass beads) as per IRC:35/latest code.
For Urban Roads as mentioned in Appendix and as per the direction of Engineer-in-Charge - Providing & fixing of reflective pavement markers Road Markers/Road Studs with micro prismatic Lense Reflector- Providing and fixing of road stud 100 x 100 mm, die-cast moulded from ASA (Acrylic Strene Acrylonitrite) High impact poly styrene or ABS (Acrylonitrile Butadiene Styrene).
Providing repairs & painting to median & kerbs, islands, dividers.
Maintenance of shoulders as per MORTH Specifications- 305.
Double Lane - Rate shall be quoted assuming per kilometre carpet area as 7000m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Double Lane with Paved Shoulders of width ______________.
Item No.
In words
Providing Re-Application of Thermoplastic Road Marking at the interval of minimum 2 years in Double Lane and Multi Lanes including auxiliary items as per the MORTH/IRC latest Specifications & as per the direction of Engineer-in-charge with the following items of works to obtain the required service level
Providing centre line and lane line marking (Hot Applied Thermoplastic compound 2.5 mm thick including reflect rising glass beads) as per IRC:35/latest code.
Providing Continuous edge line marking (Hot Applied Thermoplastic compound 2.5mm thick including reflect rising glass beads) as per IRC:35/latest code.
For Urban Roads as mentioned in Appendix and as per the direction of Engineer-in-Charge - Providing & fixing of reflective pavement markers Road Markers/Road Studs with micro prismatic Lense Reflector- Providing & fixing of road stud 100 x 100 mm, die-cast moulded from ASA (Acrylic Strene Acrylonitrite) High impact poly styrene or ABS (Acrylonitrile Butadiene Styrene).
Item No.
In words
(a) Drain Work
5.05 B Tech
2.04 II (ii) B
Amount ₹ INR
Estimated Cost Value (ECV) (₹ in Lakh) Note:- ECV includes cost of OM,IR,MI (Including Strenghthening), PM (Including Re-Application of Road Marking) With Royalty, Seigniorage Fee, Labour Cess, GST & all other Prevalent Taxes
Time of Completion in Months
Last Date of Uploading of Tender
Bid Security
Cost of BOQ
Name of the Contractor
Address of the Contractor
Description of Item
Ordinary Maintenance Services in the following Roads (with chainage): -
Runnisaidpur-Belsand-Parsauni Road 0-8.76 KM
Sitamarhi-Riga-Dheng Road 0-22.755 KM
Riga-Majorganj Road 0-17.00 KM
Kushmari-Basantpatti Road 0-10.34 KM
Parsauni-Riga Road 0-15.00 KM
Majorganj-Dheng Road 0-10.90 KM
Sisaula- Akhta Road 0-4.564 KM
Narha-Dumri Road 0-9.05 KM
Belsand-Chhitauni Road 0-4.00 KM
Partapur-Gisara-Bari Bazar (Dumra) 0-18.00 KM
Kusumari to Khairwa Road 0-4.99 KM
Sisaula to Basantpatti 0-7.44 KM
Left over portion of NH-104/227 (New) Pamra to Mehsaul Chowk 0-10.10 KM
N.H. 77-Murliyachak Road 0-4.60 KM
Runnisaidpur-Belsand-Parsauni Road 13.04-21.80 KM
Phulwariya Ghat to Bahar village 0-24.05 KM
Bahar village to Kanhauli 0-10.925 KM
Item No.
In words
Repairs to shoulders /Construction of Earthen shoulders on both sides of the carriageway wherever required to bring the service level (with 3% camber) (i) Earthen Shoulder: (a) High Shoulder (b) Low shoulder (ii) Hard Shoulder: (a) Paved Shoulder/ Granular (b) Footpath
Plantation in medians and islands not maintained by other agencies.
Pruning of trees to get 5.5 m height above the pavement.
Repairs and cleaning to Cross Drainage Works including Culverts and side drains (outside the area of Municipal Corporation and Nagar Parishad) to specified service levels by taking up required items ensuring to minimum quantity as per Section 5D of Technical Specification.
Providing Road safety and informatory items complete as per IRC:67 latest code specifications such as;
Providing and fixing new mandatory, cautionary and informatory Retro Reflectorized signage, ensuring minimum quantity as per Section 5D of Technical Specification.
Maintenance of existing signages ensuring minimum quantity as per Section 5D of Technical Specification.
Fixing new and maintenance of existing KM stones as per MORTH Specifications ensuring minimum quantity as per Section 5D of Technical Specification.
Fixing New & Maintenance of existing Guard stones/ Guide post as per MORTH Specifications ensuring minimum quantity as per Section 5D of Technical Specification.
Fixing New and Maintenance of existing Object Hazard Marker at the opening ends of culverts and bridges or at any other points, delineators. median markers and bollards (spring post) as required, as per MORTH Specifications ensuring minimum quantity as per Section 5D of Technical Specification.
Providing New and Maintenance of existing Rumble strips/ speed breaker or any traffic calming measures on minor/major roads as per MORTH Specifications ensuring minimum quantity as per Section 5D of Technical Specification.
Providing new and maintenance of existing Road marking as per IRC: 35/latest code-
Hot Applied Thermoplastic compound 2.5mm thick including reflectorising glass beads with (Clause 803-Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface-Providing & laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @250gm/sqm area, thickness of 2.5mm is exclusive of surface applied glass beads as per IRC:35 latest code. The finished surface to be level, uniform & free from streaks & holes). i. Centre line, lane line marking as per IRC: 35 latest code or as per existing road markings. ii. Edge line marking for all lanes/ roads as per IRC:35 latest code or as per existing road markings. Ensuring minimum quantity as per Section 5D of Technical Specification.
For Urban roads as mentioned in Appendix and as per the direction of Engineer-in-charge: Providing & fixing of reflective pavement markers (Road studs (Road Markers/Road Stud with micro prismatic Lense Reflector- Providing & fixing of road stud 100x100mm, die-cast moulded from ASA (Acrylic Strene Acrylonitrite) High impact poly styrene or ABS (Acrylonitrile Butadiene Styrene) body resistant to minimum support a load of 13635 Kg and Fitted with micro prismatic Lence Reflector installed in concrete or asphaltic surface by drilling hole 30mm upto a depth of 60mm and bedded in a suitable bituminous grout or epoxy mortar, all as per MORTH Specifications ensuring minimum quantity as per Section 5D of Technical Specification.
Repair and Painting of road side assets including painting of trees & poles on formation width; (a) Repair of dividers, road kerbs, islands, parapets and RCC/Brick drains (b) Painting of Trees and Poles Painting of road divider, island, parapets, kerbs etc. ensuring minimum quantity as per Section 5D of Technical Specification.
Any additional activities the Bidder considers necessary to achieve the Service Level Objective.
Item No.
In words
Tack Coat (Clause-503) - Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom
BC 30mm (Clause 507) - Providing and laying Bituminous Concrete with 100-120 TPH batch type Hot Mix Plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification (5th revision) Clause No. 507 complete in all respects.
Maintenance of Shoulders as per MORTH Specification 305.
Thermoplastic Edge Line Marking.
Painting of Parapets, Kerbs, Islands, Dividers.
Cats Eye
Single lane (Carriage way width < 3.75m) (30 mm thick BC). Rate shall be quoted assuming per kilometre carpet area as 3750m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Intermediate lane (30 mm thick BC) (Carriage way width > 3.75 and < 7.0 m). Rate shall be quoted assuming per kilometre carpet area as 5500 m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Providing 40mm thick BC for Periodical Maintenance to Double and Multi lanes including profile correction (Carriage width ≥ 7.0m) with the following items of work to obtain the required service level.
Tack Coat (Clause-503) - Providing and applying Tack Coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/ granular surface cleaned with mechanical broom.
BC (Clause-507) - Providing and laying Bituminous Concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 to 5.6 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification (5th revision) Clause No. 507 complete in all respects.
Providing shoulder width 2.5m using with 3% camber to the required the service level for low shoulders as per MORTH Specification Clause 305.
Providing centre line and lane line marking (Hot Applied Thermoplastic compound 2.5 mm thick including reflect rising glass beads) as per IRC:35/latest code.
Providing Continuous edge line marking (Hot Applied Thermoplastic compound 2.5mm thick including reflect rising glass beads) as per IRC:35/latest code.
For Urban & Rural Roads as mentioned in Appendix and as per the direction of Engineer-in-Charge - Providing & fixing of reflective pavement markers Road Markers/Road Studs with micro prismatic Lense Reflector- Providing and fixing of road stud 100 x 100 mm, die-cast moulded from ASA (Acrylic Strene Acrylonitrite) High impact poly styrene or ABS (Acrylonitrile Butadiene Styrene).
Providing repairs & painting to median & kerbs, islands, dividers.
Maintenance of shoulders as per MORTH Specifications- 305.
Double Lane - Rate shall be quoted assuming per kilometre carpet area as 7000m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Double Lane with Paved Shoulders of width ______________.
Providing Periodic Maintenance to Single and Intermediate Lanes including profile correction with the following items of works to obtain the required service level.
Tack Coat (Clause-503) - Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom
BC 30mm (Clause 519) – Recycling pavement by cold milling of existing bituminous layers, planning the surface after cold milling, reclaiming excavated material to the extent of 30 percent of the required quantity, hauling and stock piling the reclaimed material near the central recycling plant after carrying out necessary checks and evaluation, adding fresh material including rejuvenators as required, mixing in a hot mix plant, transporting and laying at site and compacting to the required the grade, level and the thickness, all as specified in clause 519.
Maintenance of Shoulders as per MORTH Specification 305.
Thermoplastic Edge Line Marking.
Painting of Parapets, Kerbs, Islands, Dividers.
Cats Eye
Single lane (Carriage way width < 3.75m) (30 mm thick BC). Rate shall be quoted assuming per kilometre carpet area as 3750m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Intermediate lane (30 mm thick BC) (Carriage way width > 3.75 and < 7.0 m). Rate shall be quoted assuming per kilometre carpet area as 5500 m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Providing 40mm thick BC for Periodical Maintenance to Double and Multi lanes including profile correction (Carriage width ≥ 7.0m) with the following items of work to obtain the required service level.
Tack Coat (Clause-503) - Providing and applying Tack Coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/ granular surface cleaned with mechanical broom.
BC (Clause-519) – Recycling pavement by cold milling of existing bituminous layers, planning the surface after cold milling, reclaiming excavated material to the extent of 30 percent of the required quantity, hauling and stock piling the reclaimed material near the central recycling plant after carrying out necessary checks and evaluation, adding fresh material including rejuvenators as required, mixing in a hot mix plant, transporting and laying at site and compacting to the required the grade, level and the thickness, all as specified in clause 519.
Providing shoulder width 2.5m using with 3% camber to the required the service level for low shoulders as per MORTH Specification Clause 305.
Providing centre line and lane line marking (Hot Applied Thermoplastic compound 2.5 mm thick including reflect rising glass beads) as per IRC:35/latest code.
Providing Continuous edge line marking (Hot Applied Thermoplastic compound 2.5mm thick including reflect rising glass beads) as per IRC:35/latest code.
For Urban Roads & Rural as mentioned in Appendix and as per the direction of Engineer-in-Charge - Providing & fixing of reflective pavement markers Road Markers/Road Studs with micro prismatic Lense Reflector- Providing and fixing of road stud 100 x 100 mm, die-cast moulded from ASA (Acrylic Strene Acrylonitrite) High impact poly styrene or ABS (Acrylonitrile Butadiene Styrene).
Providing repairs & painting to median & kerbs, islands, dividers.
Maintenance of shoulders as per MORTH Specifications- 305.
Double Lane - Rate shall be quoted assuming per kilometre carpet area as 7000m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Double Lane with Paved Shoulders of width ______________.
Providing Periodic Maintenance to Single and Intermediate Lanes including profile correction with the following items of works to obtain the required service level.
Tack Coat (Clause-503) - Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom
BC 30mm (Clause 518) – Providing laying and rolling of bituminous cold mix on prepared base consisting of a mixture of unheated mineral aggregate and emulsified or cutback bitumen, including mixing in a plant of suitable type and capacity, transporting, laying compacting and finishing to specified grades and levels.
Maintenance of Shoulders as per MORTH Specification 305.
Thermoplastic Edge Line Marking.
Painting of Parapets, Kerbs, Islands, Dividers.
Cats Eye
Single lane (Carriage way width < 3.75m) (30 mm thick BC). Rate shall be quoted assuming per kilometre carpet area as 3750m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Intermediate lane (30 mm thick BC) (Carriage way width > 3.75 and < 7.0 m). Rate shall be quoted assuming per kilometre carpet area as 5500 m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Providing 40mm thick BC for Periodical Maintenance to Double and Multi lanes including profile correction (Carriage width ≥ 7.0m) with the following items of work to obtain the required service level.
Tack Coat (Clause-503) - Providing and applying Tack Coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/ granular surface cleaned with mechanical broom.
BC 30mm (Clause 518) – Providing laying and rolling of bituminous cold mix on prepared base consisting of a mixture of unheated mineral aggregate and emulsified or cutback bitumen, including mixing in a plant of suitable type and capacity, transporting, laying compacting and finishing to specified grades and levels.
Providing shoulder width 2.5m using with 3% camber to the required the service level for low shoulders as per MORTH Specification Clause 305.
Providing centre line and lane line marking (Hot Applied Thermoplastic compound 2.5 mm thick including reflect rising glass beads) as per IRC:35/latest code.
Providing Continuous edge line marking (Hot Applied Thermoplastic compound 2.5mm thick including reflect rising glass beads) as per IRC:35/latest code.
For Urban Roads as mentioned in Appendix and as per the direction of Engineer-in-Charge - Providing & fixing of reflective pavement markers Road Markers/Road Studs with micro prismatic Lense Reflector- Providing and fixing of road stud 100 x 100 mm, die-cast moulded from ASA (Acrylic Strene Acrylonitrite) High impact poly styrene or ABS (Acrylonitrile Butadiene Styrene).
Providing repairs & painting to median & kerbs, islands, dividers.
Maintenance of shoulders as per MORTH Specifications- 305.
Double Lane - Rate shall be quoted assuming per kilometre carpet area as 7000m2. Payment shall be proportionately increased or decreased as per the actual area of the kilometre).
Double Lane with Paved Shoulders of width ______________.
Item No.
In words
Providing Re-Application of Thermoplastic Road Marking at the interval of minimum 2 years in Double Lane and Multi Lanes including auxiliary items as per the MORTH/IRC latest Specifications & as per the direction of Engineer-in-charge with the following items of works to obtain the required service level
Providing centre line and lane line marking (Hot Applied Thermoplastic compound 2.5 mm thick including reflect rising glass beads) as per IRC:35/latest code.
Providing Continuous edge line marking (Hot Applied Thermoplastic compound 2.5mm thick including reflect rising glass beads) as per IRC:35/latest code.
For Urban Roads as mentioned in Appendix and as per the direction of Engineer-in-Charge - Providing & fixing of reflective pavement markers Road Markers/Road Studs with micro prismatic Lense Reflector- Providing & fixing of road stud 100 x 100 mm, die-cast moulded from ASA (Acrylic Strene Acrylonitrite) High impact poly styrene or ABS (Acrylonitrile Butadiene Styrene).
Item No.
In words
(a) Drain Work
5.05 B Tech
2.04 II (ii) B
Amount ₹ INR
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
NIT 01.pdf
NIT • 1.54 MB
MBD 06B Pdf.pdf
NIT • 6.08 MB
NIT 01.pdf
NIT • 1.54 MB
Coriendum NIT-01 2026-27.pdf
NIT • 0.26 MB
MBD 06B Pdf.pdf
NIT • 6.08 MB
Technical Template 06B.pdf
NIT • 0.23 MB
Financial Template OPRMC-III.xlsx
NIT • 0.04 MB
Financial Template OPRMC-III.xlsx
NIT • 0.04 MB
Download all tender documents and submit your bid