Providing Lift irrigation Scheme for Horticulture Land from Pabber River to group of Villages in G P Karasa and Ukhli Mendhali Tehsil Rohru Distt Shimla HP

Amount

Cutting in earth work and disposal of excavted earth all kind of soil with in all leads and lifts as per the direction of the Engineer in Charge P&J work.

Excavation in earth work and disposal of all excavated earth upto all leads and lifts. Disposing earth to be levelled and neatly dressed pick jumper work within all leads and lifts and as directed by the Engineer-in-charge.

Excavation in foundations , trenches etc., in earth work , lift up to 1.50 metres. Stacking the eacavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15 cm. (fifteen centimetres) layers , when required in to plinth and sides of foundations etc., conslolidating each of the disposited layer by ramming and watering and then disposing off all excavated soil as directed with in the load of 20 mtrs. Pick and Jumper work etc. complete as per the direction of the Engineer - in - Charge.

Providing & Laying cement concrete 1:6:12(1ccement :6 sand: 12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinth in all leads and lifts as per the directions of the Engineer in charge.

Providing and laying cement concrete 1:3:6 (1cement: 3 sand: 6 graded stone aggregate 40mm( Forty millimeter nominal size) and curing complete excluding cost of from work in foundation and plinth with in all leads & lifts as per entire satisfication of Engineer-in-Charge.

Providing from work steel plates 3.15 mm thick welded with angle iron in frame 30x30x5 mm so as to give a fair finish i/c centering, shuttering, strutting and propping etc. with wooded battens & ballies, height of propping and centring below supporting floor to ceilling not exceeding 4 meters and removal of the same for in situ reinforced concrete and plain concrete work with in all leads aand lifts as per the direction of the Engineer in Charge.

i) Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters, buttress, plinth and string couress and the like.

ii) Flat surfaces such as soffits and suspended floors, roofs landing and the like: Floors etc up to 200 mm in thickness .

iii) Edge of slab and breaks in floors and wall under20cm wide within all leads and lifts.

iv) Foundation footing bases of column and mass concrete.

v) Column, pillar & poat upto floor two level square, rectangular and polygonal in plan.

vi) Beams, cantilevers, Girders & lintels sides and siffits of beams, hounching cantilever girder not exceeding 1 mtr. Depth.

vii) Stair cases (Except spiral stair cases) excluding landing i/c preparation of surface.

viii) Sloping and bettering surfaces I/c folding plates where inclination to horizontal plane not exceed 30 degrees.

ix) Arches upto 6.00 mts.span

Providing & fixing CI Sluice valve (with hand wheel) as per IS : 780-1984 class-I upto 300 mm dia.(i/c brass spindle & as per 2906-1984 class-II for dia.> 300 mm) complete with bolts nuts,rubber insertion etc.,(the tail piece if required shall be measured & paid for separatly)

50mm dia.

65mm dia.

Prov. & fixing SFRC Man hole cover with frame having frames size of 560 mm internal dia.should not be less than 58 kg

Providing and laying cement concrete 1:1.5:3(1cement:1.5 approved sand:3approved graded stone agg. 20mm nominal size) & curing complete excluding cost of form work in foundation and plinth:

i) Foundation and plinth (bed) with in all leads and lifts.

ii) Column, pillar & poat upto floor two level.

iii Suspended Floor roofs, landing and shelves and their support balconies, beams, girders, bressumers and contilever up to floor two level with in all leads and lifts as per the direction of the Engineer - in - Charge.

(v) Wall (any thickness but not less than 0.1 m thickness) attached pilasters,buttresses, plinth and string courses etc. from top of foundation level up to floor two level with in all leads and lifts as per the direction of the Engineer - in - Charge.

vi) Stair cases (except spiral stair cases) excluding landing i/c preparation of surface.

Providing and laying cement concrete 1:1:2 (1cement :1Sand: 2 graded stone aggregate 20 mm N/S) and curing complete excluding cost of form work and reinforcement for Rainforced concrete work in:-

i) Foundation and plinth (bed) with in all leads and lifts.

(iii) Wall (any thickness but not less than 0.1 m thickness) attached pilasters,buttresses, plinth and string courses etc. from top of foundation level up to floor two level with in all leads and lifts as per the direction of the Engineer - in - Charge.

Providing mild steel/ tor steel reinfircement for rainforced concrete work I/C bending, binding and placing in position complete upto floor two level with in all leads and lifts as per the direction of the Engineer in Charge.

Providing and laying cement concrete 1:2:4 (1cement :2 Sand: 4 graded stone aggregate 20 mm (Twenty millimeter nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in : i)Suspended Floor roofs, landing and shelves and their support balconies, beams, girders, bressumers and contilever up to floor two level with in all leads and lifts as per the direction of the Engineer - in - Charge.

(ii) Arches upto floor two level.

Providing in RCC work smooth finishing of the exposed surface with cement mortor1:3 (1cement :3 sand )with in all leads and lifts as per direction of the Engineer in Charge.

Providing and fixing pressed steel door, frames, manufactured from comercial mild steel sheet of 1.25 mm thickness including hinges jump block Jamb, beed, and if required angle threshold of mil steel angle of section 50x25mm or base ties of 1.25mm pressed mild steel welded or regidly fixed together by machanical means adjustable lugs with split and tails to each Jamb i/c steel but things 2.5mm thick with guards lock strike plate and shock as specified and applying a coat of applying steel primer after pretreatment of the surfaces directed by the Engineer-in-charge

Profile A

Profile B

Profile C

Providing and fixing Pannelled and glazed shutters for doors windows and clear storey windows including bright finish black enamel led iron butt hinges with necessary screws 40mm thick: 2nd class deodar wood.

Providing and Fixing wire gause shutter using MS wire gause if IS gause designation 85 G for doors windows clearstorey windows I/c bright finished black enamelled iron hinges with necessary secrews 30mm thick and 2nd class deodar wood.

Boulder/Stone filling behind retaing wall & crate wall within all leads and lifts and as directed by the Engineer-in-charge.

Steel work in single sections including cutting hoisting fixing in position and applying a priming coat of red lead paint in R.S. joists, channels, angles, Tees, with in all leads and lifts as directed by the Engineer -In-charge

White washing with lime on undecorated wall surfaces(two coats) to give an even shade I/c thoroughly brooming the surface to remove all dust dirt & other foreign matter. with in all leads and lifts as per the direction of the Engineer in charge.

Wire crates of GI wire filled with boulders with square cut faces against the wire (wire crates to be measured and paid for separately , with in all leads and lifts as per the direction of the Engineer - in - Charge.

Wire crates made of GI wire filled with boulders with square cut faces against the wire (boulder filling to be measured and paid for separately , with in all leads and lifts as per the direction of the Engineer - in - Charge. GI wire 5mm thick corresponding to SWG-6 15x15 mesh.

Half Brick masonary using common burnt clay building bricks above plinth upto floor two level in cm 1:4(1cement:4sand)conventiohal brick first class within all leads and lifts and as directed by the Engineer-in-charge.

15 mm thick cement plaster on fair sides of brick/stone masonery convrete walls for interior plastering upto floor two level including arises internal rounded angles not exceeding 80mm girth in cm 1:6 (1cement:6sand)

20 mm thick cement plaster on rough sides of brick/stone masonery convrete walls for interior plastering upto floor two level including arises internal rounded angles not exceeding 80mm girth in cm 1:6 (1cement:6sand)

10mm cement plastering in single coat on fair side of brick/concrete wall for internal plastering upto floor two level i/c arrises internal angles, chamfers and rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:3 (1cement : 3 Sand ) with in all leads and lifts as per direction of the Engineer in Charge.

6 mm thick cement plaster in CM 1:3( 1cement 3 sand in roof slabs

Wall painting (Two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface.

Finishing wall with water profing cement paint of approved brand and manufacture and of rerquired shade on undecorated wall surfaces (two coats) to give an even shade after thoroughly brushing the surface to remove all dirt and remains of loose powdered materials.

Applying priming coat over new wood and wood based surface after and including preparing the surface by throughly cleaning oil grease & dirt and other foreign matters.

Painting two coats(excluding priming coat) on new wood and wood based surfaces with ready mixed paint brushing to give even shade including cleaning all dirt, dust and other foreign matters white paint

Painting two coats(excluding priming coat) on new wood and wood based surfaces with ready mixed paint brushing to give even shade including cleaning all dirt, dust and other foreign matters other than white paint

Stone soling properly hand packed filling interstices with spalls and consolidating with power road roller to the required gradient and camber including spreading watering and rolling of binding materials moorum or earth etc. 100mm spread thickness (finished work including materials and laboour) within all leads and lifts and as directed by the Engineer-in-charge.

Providing and fixing of MS grill of required patttern in wooden frame of window etc. with MS rounded headed bolts and nuts or by screw: Plain Grill within all leads and lifts and as directed by the Engineer-in-charge.

Providing and fixing anodized Mild Steel sliding door bolts withnuts and screws complete I) 250mmX16mm with in all leads and lifts as per the direction of the Engineer in charge.

Providing and fixing anodized aiuminium. tower bolts barrel type with screws etc. complete.

I) 200mmX10mm

ii) 100mmx10mm

Providing and fixing anodized mild steel .handles with screws etc. complete. with in all leads and lifts as per the direction of the Engineer in charge.

I)125mm dia

ii) 100mm dia

Providing 40x3 mm flat iron hold fast 40cm. Long including fixing to frame with 10mm dia metres bolts, nuts and wooden plug and embedding in cement concrete block 30x10x15cm. 1:3:6( 1cement:3sand:6 graded stone att. 20mm nominal size) within all leads and per the directions of the Engineer in charge.

Supplying of various materials for pump house.

(i)Tool Kit for Pump house (24 items) with all accessory etc.

(i) Insulation mate (6'x4'), Bearing puller, insulation gloves & gress gen 1 No each ofr pump house

(iii) Steel / C.I.chairs,Poly table & stool 1 no each for pump house.

(iv) P/F of gantry girder 1 No each of pump house( 1.5 T)

Supplying and fixing woven plain GI fencing of mesh 50 to 150mm to any type of standard rails strainging bolts etc. i/c provision of binding wire etc.

Providing & fixing of Finalax pipe 40 mm dia. Under floor ( for connection cables ) including all req. fitting i:e elbows,sockets etc.

Providing and laying heavy duty precast cement conrete inter locking precast cement conrete inter locking paver blocks vibro compacted upto M-50 grade i/c border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks i/c curing rubbing & polishing complete (Sub base concrete floor to be paid for 60mm thick inter locking blocks

Providing and fixing 10mm thick antiskid water proof stain and impect resitent resistent heavy duty vetrified tiles Nitco or equivalent 600x600mmx10mm manufactured or approved shade and colour in flooring and landings laid over (12mm thick cement mortar 1:3)(1Cement:3Sand)jointed with cement slurry mixed with pigment to match the shade of tiles as required complete within all leads and lifts and as directed by the Engineer-in- charge..

Providing and fixing 0.45mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge.

Providing and fixing ridges or hips 60 cm overall with 0.45mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia metre with prepainted limpet and rubber washers complete with all accesoriees as required as per the direction of Engineer-in-charge.

Providing and fixing prepainted steel sheet ceiling with 0.30mm thick in panets of steel channels base frame in ceiling with screws complete (steel channels base frame to be measured and paid for separately

Providing and fixing anodised aluminium work for door, window, ventilators &partitions with extruded built up standard tubular and other sections of approved make conforming to IS 733 and IS 1285 anodised according to IS1868.(Minimum anodic coating of grade AC 15) fixed with rawlplugs and screws up of gaps at junctions, at top, felt etc. Aluminium sections shall be smooth,All complete as per architectural drawings and the direction of Eingineer-in-charge

P/F in position rolling steel shutters with vertical chanels 20 mm x 10 mm x 2 mm & braced with flat iran diagonals 20mm x 5mm size with top and bottom rail of t iron 40 mm x 40 mm x6 mm with 38 mm dia steel pulley complate with bolts and nuts lockin arrangments , stoppers ,handles including appling a priming coat of red lead paint.

Providing and fixing glazing in aluminium door and windows ,ventilater shutters and partition etc.with PVC/ neorens gasket etc. complete as per the architewctural drawing and the directions of Engineer-in-Charge(cost of aluminium snap beadingshall be paidin basic item) glazing with glass panes of 5.50 mm thickness (weight not less than 13.75 kg/sqm.ly

Providing and placing horizontal layers filtering media duly graded screened washed and cleaned as specified by the Engineer Incharge with in all leads and lifts.

(i) Prov. Dry Bricks for filter bed/septic tanks

(ii) Coarse sand 3mm to 6mm

Providing plinth protection 50mm thick in cement concrete 1:3:6(1cement:3sand:6graded stone agg. 20mm nominal size) i/c finishing the top surface of concrete smooth within all leads and lifts and as directed by the Engineer-in-charge.

Providing and fixing vitreous China wash down water closet (European type. W.C. Pan) with integral 'P' or 'S' trap including jointing the trap with soil pipe in cement mortar 1:1 (1Cement : 1 Sand) (Seat and cover to be measured and paid for separately) Ordinary type.

Providing and fixing Stainless steel kitchen sink with drain board with in all leads and lifts as per the directions of the Engineer in charge. 470X 420X 178MM

Prorviding and fixing vitreous china wash basin with single hole for piller tap with C.I. or M.S. brackets painted white Flat back 630mmx450mm within all leads and lifts and as directed by the Engineer-in-charge.including cutting holes and making good the same but excluding fittings:-with in all leads and lifts as per the directions of the Engineer in charge.

Providing and fixing PTMT Coloured / white high density polyethlylene / poly propylene 10 liters cap. full flush European standard control low level flushing Cistern with fitting and within all leads and lifts and as directed by the Engin

P/F C.P. brass waste for wash basin or sink (i)32mm diawith in all leads and lifts as per the directions of the Engineer in charge.

P/F C.P. soap dish with C.P. brass brackets fixed to wooden cleats With C.P. brass screws with in all leads and lifts as per the directions of the Engineer in charge.

P/F C.P. Brass Bib tap with capstan head(15mm dia) with in all leads and lifts as per the directions of the Engineer in charge.

P/F brass full wheel valve with capstan head(15mm dia)within all leads and lifts and as directed by the Engineer-in-charge,

P/F C.P. Angle cock 15mm dia within all leads and lifts as per the directions of the Engineer-in-charge,

P/F of GI Elbow 15mm with in all leads and lifts as per the directions of the Engineer in charge.

P/F of GI Tee 15mm with in all leads and lifts as per the directions of the Engineer in charge.

P/F of GI Nipple 15mm with in all leads and lifts as per the directions of the Engineer in charge.

Providing and laying galvanized mild steel tube (heavy class) in wall. Ceiling including with in all leads and lifts as per the directions of the Engineer in charge .15mm dia(fiifteen milimetres)nominal size.(H . C )

Providing and fixing 600mmx450mm bevelled edge miror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screws and washers. within all leads and lifts and as directed by the Engineer-in-charge.

Providing and fixing in trenches 10 Kg.f/cum2 working pressure unplasticized P.V.C. pipe (Conforming to IS: 4985-1968) complete fittings (earth work in trenches to be measured and paid for separately):-

a)110 mm out side diameter.

b)Elbow 100 mm dia.

c)Clamps 100mm dia.

d)Door Bends

e)Plain bends

f)Collar

g) Cowl

h)Floor Traps

h)Floor Traps

h)Floor Traps

Wiring for light point/fan point/exhaust fan/call bell point with 1.5 Sq.mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in PVC Conduit conductor and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. with in all leads and lifts as per direction of the Engineer-in-Charge. Group ( A.)

Wiring for power plug with 2x4 Sq.mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke sinlge core (flexible) copper conductor cable in PVC Conduit along with 1 No. 4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.with in all leads and lifts as per direction of the Engineer-in-Charge. Group (A.)

Wiring for power plug with 4x4 Sq.mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke sinlge core (flexible) copper conductor cable in PVC Conduit along with 2 No. 4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required.with in all leads and lifts as per direction of the Engineer-in-Charge. Group (A.)

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke sinlge core (flexible) copper conductor cable in PVC Conduit along with 1 No. HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required. with in all leads and lifts as per direction of the Engineer-in-Charge.

2x1.5 Sq.mm.

2x10 Sq.mm.

Supplying & Fixing metal boxes of following sizes (nominal size) on surface or in recess suitable for fixing phenolic laminated sheet cover in front including painting etc. as required. with in all leads and lifts as per direction of the Engineer-in-Charge.

100mm.x100mm.x60mm. Deep.

180mm.x100mm.x60mm. Deep.

200mm.x150mm.x75mm. Deep.

200mm.x250mm.x100mm. Deep.

Supplying and fixing following rating Piano-type switch/socket on the existing switch box/cover including connections etc. as required. with in all leads and lifts as per direction of the Engineer-in-Charge.

S.P. 5/6 Amps one way switch, piano type.

S.P. 15/16 Amps one way switch, porcelain base/paino type.

5 pin 5/6 Amps socket outlet, poreclain base/piano type.

6 pin 15/16 Amps socket outlet, porcelain base/piano type.

Supplying and fixing bakelite batten/angle holder including connections etc. as required. with in all leads and lifts as per direction of the Engineer-in-Charge.

Supplying and erection of 6 amps, to 32 amps, rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required. with in all leads and lifts as per direction of the Engineer-in-Charge. Single pole . Cat-A

Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. with in all leads and lifts as per direction of the Engineer-in-Charge. 40 Amps. Cat- A

Supplying and fixing of following way, single pole and netural sheet steel MCB distribution board, 240 volts, on surface/recess, complete with tinned copper bus-bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels inter-connections phosphatized and powder painted, including earthing etc. as required. with in all leads and lifts as per direction of the Engineer-in-Charge. Single door-6 way

Earthing with G.I. earth pipe 4.5mtr. Long and 40mm dia, including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal or coke and salt) complete as required. with in all leads and lifts as per direction of the Engineer-in-Charge.

Extra for using salt and charcoal for pipe earth eletrode complete as required. with in all leads and lifts as per direction of the Engineer-in-Charge.

Supplying and laying 6 SWG G.I. wire at 0.50 mtr. Below ground level for earth electrode conductor, including soldering etc. as required. with in all leads and lifts as per direction of the Engineer-in-Charge.

Providing and fixing sleek and decorative strip type fixture with domestic electronic ballast and colored engineering plastic end plates, suitable for 28 watt FTL (T5), complete with all accessoris (excluding the T-8 tube), connections, testing and commissioning etc. as required. 1x 28 watt-FTL (T5) (Category-A with in all leads and lifts as per direction of the Engineer-in-Charge.

Providing, Installation, testing and commissioning of ceiling fan with regulator, including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required. with in all leads and lifts as per direction of the Engineer-in-Charge.

Supplying and fixing Ding-Dong/Electronic musical bell, suitable for D.C./A.C. single phase, 230 volts complete as required. with in all leads and lifts as per direction of the Engineer-in-Charge.

Supplying and fixing of integral CFL Post Top Lantern of following capacity, cast aluminium spigot, spun alumnium canopy, opal acrylic diffuser, complete with all accessoreis but excluding CFL lamp including making connections, testing etc. as required. Gate post top lantern-FCL 26 watt. with in all leads and lifts as per direction of the Engineer-in-Charge.

Providing laying and fixing of one No. aluminuim conductor, PVC insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade on surface etc. of the required size. Armoured cable 4 sq. m (twin core) with in all leads and lifts as per direction of the Engineer-in-Charge.

Supplying and fixing Solar Street lights are raised light sources which are powed by solar panels generally mounted on the lighting structure or integated into the pole itself . The solar panels charge a rechargeable battery which powers a fluorescent of LED lamp during the night with in all leads and lifts as per direction of the Engineer-in-Charge. (Single panel) 9 watt

Manufacturing and fixing wheel box MS chamber of size 90x60x30 CM with M.S Sheet (2.50 mm or (12 B.G.) thick) duly welded with angle iron of Angles Iron 40x40x5mm and also provided extra length of 250mm of same angle (as tee) in the bottom of all four legs for embending in cement concrete C.C. 1 :2 :4 and top opening will provide with hinges with lock arrangement etc.complete and also providing hole on three sides of chamber for crossing different size of pipes and as per satisfaction of Engineer-in-charge including entire carriage of material upto all leads and lifts

Making of Common header for distribution system of water at Storage Tanks including all fitting and fixing as per drawing etc.with all leads and lifts as per direction and satisfactions of Engineer in charge

Laying , jointing and testing in trenches Galvanised Mild Steel tube of the following dia metres including smooth bending by necessary bends, or through pipe bending machine with necessary all pipe fittings such as Tees, Elbows, Union & Reducers etc. of ISI marked & testing for leakage complete with in all leads & lifts as per entire satisfication of Engineer - in - charge. (Earth work in trenches to be measured and paid for separately

50mm dia.

65mm dia.

Tarsem Chand Associates

Vikram Rithwan Contractor

HYDRAULIC ENGINEERING COMPANY