Loading…
Loading…
Tender Value
₹45.5 L
EMD Value
₹91,000
Closing Date
17 Jun 2026, 11:00 am
Essential routine repair/maintenance works to Officers Qtrs, Bungalows and Service Buildings at Railway Officers colonies at Sterling Garden & Pycrofts Garden , Nungambakkam
MAS16OF26067B
MAS16OF26067B
Open
3 Months
Thiruvallur, Tamil Nadu
₹0
₹91,000
26 May 2026
26 May 2026
3 Jun 2026
Buildings at Railway Officers colonies at Sterling Garden & Pycrofts Garden , Nungambakkam
S No. Item No Description of Item Unit Qty Rate Amount
1.0 CARRIAGE OF MATERIALS
By Mechanical Transport including loading,
unloading and stacking
1.1.18 Disposal of moorum/building rubbish/ malba/ cum 97.26 494.1 48056.17
similar unserviceable, dismantled or waste
material by mechanical transport including
1 loading, transporting, unloading to approved
municipal dumping ground for lead upto 10 km
for all lifts, complete as per directions of
Engineer-in-charge.
2.0 EARTH WORK
2.1S General
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
Excavating trenches by mechanical/manual
means of required width for pipes, cables, etc
including excavation for sockets, and dressing
of sides, ramming of bottoms, for all depth,
including getting out the excavated soil, and
2.10 then returning the soil as required, in layers
not exceeding 20 cm in depth, including
consolidating each deposited layer by
ramming, watering, etc. and disposing of
surplus excavated soil as directed, within a
2.10.1 All kinds of soil
2 2.10.1.1 Pipes, cables etc, not exceeding 80 mm dia. Metre 171 215.6 36867.6
2.25 Filling available excavated earth (excluding cum 184.68 196 36197.28
rock) in trenches, plinth, sides of foundations
etc. in layers not exceeding 20 cm in depth,
consolidating each deposited layer by
ramming and watering, lead up to 50 and for
Supplying chemical emulsion in sealed
containers including delivery as specified.
2.34.1 Chlorpyriphos/ Lindane emulsifiable Litre 19 234.75 4460.25
concentrate of 20%
Diluting and injecting chemical emulsion for
POST-CONSTRUCTIONAL anti-termite
treatment (excluding the cost of chemical
Treatment of soil under existing floors using
chemical emulsion @ one litre per hole, 300
mm apart including drilling 12 mm diameter
holes and plugging with cement mortar 1 :2 (1
cement : 2 Coarse sand) to match the existing
2.35.3.1 With Chlorpyriphos/Lindane E.C. 20% with 1% Sqm 662.42 310.05 205383.32
2.35.5 Treatment at points of contact of wood work Metre 302.1 279.7 84497.37
by chemical emulsion Chlorpyriphos/ Lindane
(in oil or kerosene based solution) @ 0.5 litres
per hole by drilling 6 mm dia holes at
downward angle of 45 degree at 150 mm
centre to centre and sealing the same.
4.0 CONCRETE WORK
4.1S CEMENT CONCRETE (CAST IN SITU)
Providing and laying in position cement
concrete of specified grade excluding the cost
of centering and shuttering - All work up to
derived from natural sources : 4 graded stone
aggregate 20 mm nominal size derived from
natural sources)
6.0 MASONRY WORK
6.1S General
Brick work with common burnt clay F.P.S. (non
modular) bricks of class designation 7.5 in
superstructure above plinth level up to floor V
level in all shapes and sizes in :
6.12S HALF BRICK MASONRY
Half brick masonry with common burnt clay
F.P.S. (non modular) bricks of class
designation 7.5 in superstructure above plinth
level up to floor V level.
8.0 CLADDING WORK
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
8.1S General
Providing and fixing 18 mm thick gang saw
cut, mirror polished, premoulded and
prepolished, machine cut for kitchen
platforms, vanity counters, window sills, facias
and similar locations of required size,
approved shade, colour and texture laid over
20 mm thick base cement mortar 1:4 (1
cement : 4 coarse sand), joints treated with
white cement, mixed with matching pigment,
epoxy touch ups, including rubbing, curing,
moulding and polishing to edges to give high
gloss finish etc. complete at all levels
Granite stone slab colour black, Cherry/Ruby
Providing edge moulding to 18 mm thick
marble stone counters, Vanities etc., including
8.3 machine polishing to edge to give high gloss
finish etc. complete as per design approved by
Engineer-in-Charge.
8.5 Extra for providing opening of required size & Each 7 978.7 6850.9
shape for wash basin/ kitchen sink in kitchen
platform, vanity counter and similar location in
12 marble/ Granite/ stone work, including
necessary holes for pillar taps etc. including
moulding, rubbing and polishing of cut edges
8.20S STONE WORK DRY CLADDING
8.31 Providing and fixing Ist quality ceramic glazed Sqm 74 1267.95 93828.3
wall tiles conforming to IS: 15622 (thickness to
be specified by the manufacturer), of
approved make, in all colours, shades except
burgundy, bottle green, black of any size as
approved by Engineer-in-Charge, in skirting,
risers of steps and dados, over 12 mm thick
bed of cement mortar 1:3 (1 cement : 3 coarse
sand) and jointing with grey cement slurry @
3.3kg per sqm, including pointing in white
cement mixed with pigment of matching
shade complete.
9.0 WOOD AND P.V.C. WORK
9.1S FRAMES AND TRUSSES
Providing wood work in frames of doors,
windows, clerestory windows and other
frames, wrought framed and fixed in position
with hold fast lugs or with dash fasteners of
required dia & length (hold fast lugs or dash
fastener shall be paid for separately).
Providing and fixing panelling or panelling and
glazing in panelled or panelled and glazed
shutters for doors, windows and clerestory
windows (Area of opening for panel inserts
excluding portion inside grooves or rebates to
be measured). Panelling for panelled or
panelled and glazed shutters 25 mm to 40 mm
9.7.7 Float glass panes
9.7.7.2 5.0 mm thick glass panes (weight not less than Sqm 4 2600.45 10401.8
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
Providing and fixing ISI marked flush door
shutters conforming to IS : 2202 (Part I)
decorative type, core of block board
9.20 construction with frame of 1st class hard wood
and well matched teak 3 ply veneering with
vertical grains or cross bands and face
veneers on both faces of shutters.
9.20.2 30 mm thick including ISI marked Stainless Sqm 14.36 3167.95 45491.76
Steel butt hinges with necessary screws
9.23 Extra for providing lipping with 2nd class teak Sqm 14.36 462.35 6639.35
wood battens 25 mm minimum depth on all
edges of flush door shutters (over all area of
door shutter to be measured).
9.40S MISCELLANEOUS-WOOD WORK
Providing and fixing chromium plated brass
curtain rod having wall thickness of 1.25mm
9.46 with two chromium plated brass brackets fixed
with C.P. brass screws and PVC sleeves etc.,
wherever necessary complete :
Providing and fixing M.S. grills of required
pattern in frames of windows etc. with M.S.
9.48 flats, square or round bars etc. including
priming coat with approved steel primer all
9.48.2 Fixed to openings /wooden frames with rawl Kg 190 238.35 45286.5
plugs screws etc.
9.53 Providing 40x5 mm flat iron hold fast 400 mm Each 46 228.85 10527.1
long including fixing to frame with 10 mm
diameter bolts, nuts and wooden plugs and
20 embedding in cement concrete block
300x100x150 mm 1:3:6 mix (1 cement : 3
coarse sand : 6 graded stone aggregate 20
mm nominal size).
9.70S STAINLESS STEEL FITTINGS
Providing and fixing IS : 12817 marked
9.71 stainless steel butt hinges (heavy weight) with
stainless steel screws etc. complete :
9.72S BRASS FITTINGS
Providing and fixing bright finished brass butt
hinges with necessary screws etc. complete :
Providing and fixing bright finished brass tower
9.74 bolts (barrel type) with necessary screws etc.
9.83 Providing and fixing aluminium die cast body Each 4 1124.85 4499.4
tubular type universal hydraulic door closer
(having brand logo with ISI, IS : 3564,
embossed on the body, door weight upto 35 kg
and door width upto 700 mm), with necessary
accessories and screws etc. complete.
9.88S CHROMIUM PLATED BRASS FITTINGS
9.88 Providing and fixing chromium plated brass Each 4 998.35 3993.4
100 mm mortice latch and lock with 6 levers
and a pair of lever handles of approved quality
with necessary screws etc. complete.
9.89 Providing and fixing chromium plated brass Each 7 952.8 6669.6
26 night latch of approved quality including
necessary screws etc. complete.
Providing and fixing special quality chromium
plated brass cupboard locks with six levers of
approved quality including necessary screws
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
Providing and fixing chromium plated brass
handles with necessary screws etc. complete:
ANODISED ALUMINIUM FITTINGS (ALL FITTINGS
SHALL BE ISI MARKED)
Providing and fixing aluminium sliding door
bolts, ISI marked anodised (anodic coating not
9.96 less than grade AC 10 as per IS : 1868),
transparent or dyed to required colour or
shade, with nuts and screws etc. complete :
Providing and fixing aluminium tower bolts, ISI
marked, anodised (anodic coating not less
9.97 than grade AC 10 as per IS : 1868 )
transparent or dyed to required colour or
shade, with necessary screws etc. complete :
Providing and fixing aluminium handles, ISI
marked, anodised (anodic coating not less
9.100 than grade AC 10 as per IS : 1868) transparent
or dyed to required colour or shade, with
necessary screws etc. complete :
Providing and fixing aluminium hanging floor
door stopper, ISI marked, anodised (anodic
coating not less than grade AC 10 as per IS :
1868) transparent or dyed to required colour
and shade, with necessary screws etc.
9.105S GYPSUM BOARD PARTITIONS
9.110 Providing and fixing Bamboo jaffery/ fencing Sqm 213.75 689.4 147359.25
consisting of superior quality 25mm dia
(Average) half cut bamboo placed vertically
and fixed together with three numbers
horizontal running members of hollock wood in
scantling of section 50X25 mm, fixed with
nails and G.I wire on existing support complete
as per direction of Engineer-in-charge.
Providing and fixing magnetic catcher of
approved quality in cupboard / ward robe
shutters, including fixing with necessary
screws etc. complete.
9.118 Providing and fixing to existing door frames.
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
9.118.1 24 mm thick factory made PVC door shutters Sqm 20 2969.25 59385
made of styles and rails of a uPVC hollow
section of size 59x24 mm and wall thickness 2
mm ( +/- 0.2 mm) with inbuilt edging on both
sides. The styles and rails mitred and joint at
the corners by means of M.S. galvanised/
plastic brackets of size 75x220 mm having
wall thickness 1.0 mm and stainless steel
screws. The styles of the shutter reinforced by
inserting galvanised M.S. tube of size 20x20
mm and 1 mm ( +/- 0.1 mm) wall thickness.
The lock rail made up of 'H' section, a uPVC
36 hollow section of size 100x24 mm and 2 mm (
+/- 0.2 mm) wall thickness, fixed to the shutter
styles by means of plastic/galvanised M.S. 'U'
cleats. The shutter frame filled with a uPVC
multi-chambered single panel of size not less
than 620 mm, having over all thickness of 20
mm and 1 mm ( +/- 0.1 mm) wall thickness.
The panels filled vertically and tie bar at two
places by inserting horizontally 6 mm
galvanised M.S. rod and fastened with nuts
and washers, complete as per manufacturer's
specification and direction of Engineer-in-
charge. (For W.C. and bathroom door shutter).
9.119 Providing and fixing factory made P.V.C. door Metre 17.96 492.7 8848.89
frame of size 50x47 mm with a wall thickness
of 5 mm, made out of extruded 5 mm rigid
PVC foam sheet, mitred at corners and joined
with 2 Nos of 150 mm long brackets of 15x15
mm M.S. square tube, the vertical door frame
37 profiles to be reinforced with 19x19 mm M.S.
square tube of 19 gauge, EPDM rubber gasket
weather seal to be provided through out the
frame. The door frame to be fixed to the wall
using M.S. screws of 65/100 mm size,
complete as per manufacturer's specification
and direction of Engineer- in-Charge.
Providing & Fixing decorative high pressure
laminated sheet of plain / wood grain in gloss /
matt/ suede finish with high density protective
9.127 surface layer and reverse side of adhesive
bonding quality conforming to IS : 2046 Type
S, including cost of adhesive of approved
Providing and fixing fly proof stainless steel
grade 304 wire gauge, to windows and
clerestory windows using wire gauge with
average width of aperture 1.4 mm in both
directions with wire of dia. 0.50 mm all
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
Providing and fixing factory made uPVC
glazed/wire mesh windows/ doors comprising
of lead free uPVC multi-chambered frame, sash
and mullion/coupler (where ever required)
extruded profiles having minimum wall
thickness of 1.70 mm for Series R1 and R2
profiles and 2.10 mm for Series R3 and R4
profiles conforming to EN: 12608 in any shape,
colour and design duly reinforced with
galvanized mild steel section made of required
shape & size as per CPWD Specification, uPVC
extruded glazing beads, interlocks and Inline
sash adaptor (where ever required) of
appropriate dimension, EPDM gasket,
hardware, SS 304 grade fasteners of minimum
8 mm dia with countersunk head, comprising
of matching polyamide PA6 grade sleeve for
fixing frame to finished wall as per IS 1367 :
Part 1 to 14, plastic packers, plastic caps and
necessary stainless steel screws etc. Profile of
frame, sash & mullion (if required) shall be
mitred cut and fusion welded/mechanically
jointed duly sealed at all corners, including
drilling of holes for fixing hardware and
drainage of water etc. After fixing frame the
gap between frame and adjacent finished wall
shall be filled with weather proof silicon
sealant over backer rod of approved size and
quality, all complete as per approved drawing
conforming to CPWD specification & direction
of Engineer-in-Charge. Section of steel
reinforcement and cross sections of uPVC
profiles to be as per design approved by
Engineer-in-Charge. Wire mesh / Glazing of
plain/ toughened/ laminated/ double glass unit
with / without high performance coatings as
per design requirements and conforming to IS:
3548 & IS: 16231 shall be paid separately.
Three track three panels sliding window with
two glazed & one wire mesh panels with
Aluminium channel for roller track, wool pile,
nylon rollers with SS 304 body.
9.147.A4.2 Using R3 series with frame (98 mm & above) x Sqm 3.47 10874.2 37733.47
(40 mm & above) & both glazed and fly screen
sash (30 mm & above) x (55 mm & above)
with zinc alloy (zamak) powder coated handle
on every glazed panel along with multi-point
locking system. (Height upto 1.8m)
Fixed window / ventilator without mullion /
9.147.C1.1 Using R1 series with frame (33mm & above ) x Sqm 1.03 8247.25 8494.67
(35mm & above). (Height upto 0.90 meter)
Casement door single panel with zinc alloy
(zamak) 3D hinges, multi-point locking system
with cylinder, zinc alloy (zamak) powder
coated handles on both sides.
9.147.F1.1 Using R3 series with frame (55 mm & above) x Sqm 2.39 12496.05 29865.56
43 (50mm & above) & sash (55 mm & above) x
(85mm & above) (Height upto 2.5 meter).
Providing and fixing bright /matt finished
9.165 Stainless Steel handles of approved quality &
make with necessary screws etc all complete.
Providing and fixing stainless steel fancy
handle of approved make fixed with SS screws
etc. complete as per direction of Engineer-in-
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
9.172 Providing and fixing stainless steel soft closing ONE 12 885.1 10621.2
heavy type telescopic drawer channels of SET
47 approved make 500 mm long with screws etc.
complete as per directions of Engineer- in-
9.174 Providing and fixing 2 mm thick 16 to 19 mm Metre 57 43.8 2496.6
wide PVC edge binding tape of approved
quality for cupboard/wardrobe shutters
48 including necessary synthetic resin hot
pressed to edges on binding machine etc.
complete as per directions of Engineer- in-
11.0 FLOORING
11.16S TILE FLOORING
Chequered precast cement concrete tiles 22
mm thick in footpath & courtyard, jointed with
neat cement slurry mixed with pigment to
match the shade of tiles, including rubbing and
cleaning etc. complete, on 20 mm thick bed of
cement mortar 1:4 (1 cement: 4 coarse sand).
11.20.2 Medium shade pigment using 50% white Sqm 165.2 1328.35 219443.42
cement 50% Grey cement
11.26S KOTA STONE FLOORING
11.27 Kota stone slabs 20 mm thick in risers of steps, Sqm 2.57 2354.7 6051.58
skirting, dado and pillars laid on 12 mm
(average) thick cement mortar 1:3 (1 cement:
50 3 coarse sand) and jointed with grey cement
slurry mixed with pigment to match the shade
of the slabs, including rubbing and polishing
11.41S VITRIFIED FLOOR TILES
Providing and laying vitrified floor tiles in
different sizes (thickness to be specified by the
manufacturer) with water absorption less than
0.08% and conforming to IS: 15622, of
approved make, in all colours and shades, laid
on 20mm thick cement mortar 1:4 (1 cement :
4 coarse sand), jointing with grey cement
slurry @ 3.3 kg/ sqm including grouting the
joints with white cement and matching
pigments etc., complete.
Providing and laying Vitrified tiles in floor in
different sizes (thickness to be specified by the
manufacturer) with water absorption less than
0.08% and conforming to IS:15622, of
approved brand & manufacturer, in all colours
and shade, laid on 20 mm thick cement mortar
1:4 (1 cement: 4 coarse sand) jointing with
11.41A grey cement slurry @3.3 kg/sqm including
grouting the joints with white cement and
matching pigments etc. The tiles must be cut
with the zero chipping diamond cutter only .
Laying of tiles will be done with the notch
trowel, plier, wedge, clips of required
thickness, leveling system and rubber mallet
for placing the tiles gently and easily.
11.41A.3 Glazed Vitrified tiles Matt/Antiskid finish of size
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
Providing and laying Vitrified tiles in different
sizes (thickness to be specified by
manufacturer), with water absorption less than
0.08 % and conforming to I.S. 15622, of
approved make, in all colours & shade, in
skirting, riser of steps, over 12 mm thick bed
of cement mortar 1:3 (1 cement: 3 coarse
sand), jointing with grey cement slurry @ 3.3
kg/ sqm including grouting the joint with white
cement & matching pigments etc. complete.
12.0 ROOFING
12.37S RAIN WATER SPOUT AND PIPE
Providing and fixing on wall face unplasticised
Rigid PVC rain water pipes conforming to IS :
13592 Type A, including jointing with seal ring
conforming to IS : 5382, leaving 10 mm gap
for thermal expansion, (i) Single socketed
Providing and fixing on wall face unplasticised
- PVC moulded fittings/ accessories for
unplasticised Rigid PVC rain water pipes
conforming to IS : 13592 Type A, including
jointing with seal ring conforming to IS : 5382,
leaving 10 mm gap for thermal expansion.
12.42.1 Coupler
12.42.4 Single tee without door
12.42.5 Bend 87.5 degree
12.42.6 Shoe (Plain)
12.50 Providing and fixing precoated galvanised iron Sqm 28.5 738.65 21051.53
profile sheets (size, shape and pitch of
corrugation as approved by Engineer-in-
charge) of total coated thickness 0.50 mm
(base metal of minimum 0.45 mm thickness
with total coating thickness of 0.05 mm) with
zinc coating 120 grams per sqm as per IS:
277, in 240 mpa steel grade, 5-7 microns
epoxy primer on both side of the sheet and
polyester top coat 15-18 microns. Sheet
59 should have protective guard film of 25
microns minimum to avoid scratches during
transportation and should be supplied in single
length upto 12 metre or as desired by
Engineer-in-charge. The sheet shall be fixed
using self drilling /self tapping screws of size
(5.5x 55 mm) with EPDM seal, complete upto
any pitch in horizontal/ vertical or curved
surfaces, excluding the cost of purlins, rafters
and trusses and including cutting to size and
shape wherever required.
Providing and fixing precoated galvanised
steel sheet roofing accessories of total coated
thickness 0.50 mm (base metal of minimum
0.45 mm thickness with total coating thickness
of 0.05 mm) with Zinc coating 120 grams per
sqm as per IS: 277, in 240 mpa steel grade, 5-
7 microns epoxy primer on both side of the
sheet and polyester top coat 15-18 microns
using self drilling/ self tapping screws
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
13.0 FINISHING
13.1S CEMENT PLASTER (IN FINE SAND)
15 mm cement plaster on the rough side of
single or half brick wall of mix :
13.4S CEMENT PLASTER (IN COARSE SAND)
13.6 20 mm cement plaster of mix :
13.20S PEBBLE DASH PLASTER
13.26 Providing and applying plaster of paris putty of Sqm 50 262.7 13135
2 mm thickness over plastered surface to
prepare the surface even and smooth
13.44S EXTERIOR FINISHING
Finishing walls with Acrylic Smooth exterior
paint of required shade :
13.46.1 New work (Two or more coat applied @ 1.67 Sqm 60 160.6 9636
64 ltr/10 sqm over and including priming coat of
exterior primer applied @ 0.90 litre/10 sqm)
Painting with synthetic enamel paint of
13.61 approved brand and manufacture to give an
13.80 Providing and applying white cement based Sqm 1224.59 156.05 191097.27
putty of average thickness 1 mm, of approved
66 brand and manufacturer, over the plastered
wall surface to prepare the surface even and
smooth complete.
Wall painting with premium acrylic emulsion
paint of interior grade, having VOC (Volatile
Organic Compound ) content less than 50
13.83 grams/ litre of approved brand and
manufacture, including applying additional
coats wherever required to achieve even
shade and colour.
Applying priming coats with primer of
13.85 approved brand and manufacture, having low
VOC (Volatile Organic Compound ) content.
13.85.3 With water thinnable cement primer on wall Sqm 3100 73.95 229245
68 surface having VOC content less than 50
13.88 Removing white or colour wash by scrapping Sqm 442.67 19.75 8742.73
and sand papering and preparing the surface
smooth including necessary repairs to
scratches etc. complete
13.91 Removing dry or oil bound distemper, water Sqm 3061.48 25.15 76996.22
proofing cement paint and the like by
70 scrapping, sand papering and preparing the
surface smooth including necessary repairs to
scratches etc. complete.
Painting with synthetic enamel paint of
13.99 approved brand and manufacture of required
colour to give an even shade :
Varnishing with varnish of approved brand and
72 13.113.1 One or more coats with copal varnish Sqm 514.92 94.6 48711.43
13.114 Melamine polishing on wood work (one or Sqm 260.11 138.1 35921.19
14.0 REPAIRS TO BUILDING
14.1S General
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
Repairs to plaster of thickness 12 mm to 20
mm in patches of area 2.5 sq.meters and
under, including cutting the patch in proper
shape, raking out joints and preparing and
plastering the surface of the walls complete,
including disposal of rubbish to the dumping
ground, all complete as per direction of
Engineer-in-Charge.
14.1.2 With cement mortar 1:4 (1cement: 4 coarse Sqm 9.98 560.5 5593.79
Renewing glass panes, with wooden fillets
wherever necessary:
14.6.2 Float glass panes of nominal thickness 5 mm Sqm 8 1906.4 15251.2
(weight not less than 12.5kg/sqm)
14.12 Providing and fixing 16 mm M.S. Fan clamps of Each 6.65 563.9 3749.94
standard shape and size in existing R.C.C.
slab, including cutting chase, anchoring clamp
76 to reinforcement bar, including cleaning,
refilling, making good the chase with matching
concrete, plastering and painting the exposed
portion of the clamps complete.
14.72S FINISHING
14.72 Providing and fixing double scaffolding system Sqm 68.4 338.25 23136.3
(cup lock type) on the exterior side, up to
seven story height made with 40 mm dia M.S.
tube 1.5 m centre to centre, horizontal &
vertical tubes joining with cup & lock system
with M.S. tubes, M.S. tube challies, M.S.
clamps and M.S. staircase system in the
scaffolding for working platform etc. and
maintaining it in a serviceable condition for the
required duration as approved and removing it
there after. The scaffolding system shall be
stiffened with bracings, runners, connection
with the building etc wherever required for
inspection of work at required locations with
essential safety features for the workmen etc.
complete as per directions and approval of
Engineer-in-charge .The elevational area of the
scaffolding shall be measured for payment
purpose .The payment will be made once
irrespective of duration of scaffolding.
14.75AS ROUTINE MAINTENANCE WORK
Providing & fixing White vitreous china water
closet squatting pan (Indian type) along with S
or P trap including dismantling of old WC seat
and S or P trap at site complete with all
operations including all necessary materials,
labour and disposal of dismantled material
including malba, all complete as per the
direction of Engineer-in charge.
14.82 Dismantling W. C . Pan of all sizes including Each 19 134.1 2547.9
disposal of dismantled materials including
malba all complete as per directions of
Engineer-in-Charge.
including stacking of dismantled pipes (within
50 metres lead) as per direction of Engineer-
in-Charge.(a) Internal Work- Exposed on wall
14.85 Taking out existing wooden door shutter, Each 22.8 429.1 9783.48
repair by cutting, painting etc. and refixing of
repaired door shutters to existing door frames,
including replacement of hinges with screws,
etc. as required, all complete as per the
direction of the Engineer-in-charge.
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
Providing and laying APP (Atactic
Polypropylene Polymer) modified prefabricated
five layer 3 mm thick water proofing
membrane, black finished reinforced with non-
woven polyester matt consisting of a coat of
bitumen primer for bitumen membrane @ 0.40
litre/sqm by the same membrane manufacture
of density at 25 degreeC, 0.87-0.89 kg/ litre
and viscosity 70-160 cps. Over the primer coat
the layer of membrane shall be laid using
Butane Torch and sealing all joints etc, and
14.91 preparing the surface complete. The vital
physical and chemical parameters of the
membrane shall be as under : Joint strength in
longitudinal and transverse direction at 23
degreeC as 650/ 450N/ 5cm. Tear strength in
longitudinal and transverse direction as
300/250N. Softening point of membrane not
less than 150 degreeC. Cold flexibility shall be
upto -2 degreeC when tested in accordance
with ASTM, D - 5147. The laying of membrane
shall be got done through the authorised
applicator of the manufacturer of membrane :
15.0 DISMANTLING AND DEMOLISHING
15.1S General
Demolishing cement concrete manually/ by
mechanical means including disposal of
material within 50 metres lead as per direction
of Engineer - in - charge.
(including equivalent design mix)
15.3 Demolishing R.C.C. work manually/ by cum 5.13 3551.25 18217.91
mechanical means including stacking of steel
84 bars and disposal of unserviceable material
within 50 metres lead as per direction of
Engineer - in- charge.
Demolishing brick work manually/ by
mechanical means including stacking of
15.7 serviceable material and disposal of
unserviceable material within 50 metres lead
as per direction of Engineer-in-charge.
Demolishing stone rubble masonry manually/
by mechanical means including stacking of
15.9 serviceable material and disposal of
unserviceable material within 50 metres lead
as per direction of Engineer-in-charge :
Dismantling doors, windows and clerestory
windows (steel or wood) shutter including
chowkhats, architrave, holdfasts etc. complete
and stacking within 50 metres lead :
Dismantling tile work in floors and roofs laid in
15.23 cement mortar including stacking material
within 50 metres lead.
Dismantling manually/ by mechanical means
including stacking of serviceable material and
15.43 disposal of unserviceable material within 50
metres lead as per direction of Engineer-in-
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
15.52 Dismantling of flushing cistern of all types Each 24 112.05 2689.2
(C.I./PVC/Vitreous China) including stacking of
useful materials near the site and disposal of
unserviceable materials within 50 metres lead.
15.56 Dismantling old plaster or skirting raking out Sqm 475 54.65 25958.75
joints and cleaning the surface for plaster
including disposal of rubbish to the dumping
ground within 50 metres lead.
16.0 ROAD WORK
16.1S ROADS
16.1 Preparation and consolidation of sub grade Sqm 18 218.9 3940.2
with power road roller of 8 to 12 tonne
capacity after excavating earth to an average
of 22.5 cm depth, dressing to camber and
consolidating with road roller including making
good the undulations etc. and re-rolling the
sub grade and disposal of surplus earth with
lead upto 50 metres.
Cutting road and making good the same
including supply of extra quantities of
materials i.e. aggregate, moorum screening,
red bajri and labour required.
16.30S PREMIX CARPET
Providing and applying tack coat using
bitumen emulsion conforming to IS:8887,
16.31 using emulsion pressure distributer including
preparing the surface & cleaning with
mechanical broom.
16.31.2 With medium setting bitumen emulsion
4 cm thick bitumastic sheet with hot bitumen
of approved quality, using stone chippings
(60% with 12.5 mm nominal size and 40%
with 10 mm nominal size) @ 2.60 cum per 100
sqm and coarse sand @ 2.60 cum per 100
16.39 sqm of road surface and with bitumen @ 56
kg/cum of stone chippings and @ 128 kg/cum
of sand over a tack coat with hot straight run
bitumen, including consolidation with road
roller of 8 to 10 tonne etc. complete. (tack
coat to be paid separately) :
16.39.2 With paving asphalt grade VG - 30 with no Sqm 228 568.6 129640.8
16.49S MISCELLANEOUS
Providing and fixing G.I. chain link fabric
fencing of required width in mesh size 50x50
mm including strengthening with 2 mm dia
wire or nuts, bolts and washers as required
complete as per the direction of Engineer-in-
16.70.2 Made of G.I. wire of dia. 4 mm, PVC coated to Sqm 28.5 1067.1 30412.35
96 achieve outer dia not less than 5 mm in
required colour and shade
16.79 Providing, laying, spreading and compacting cum 27.36 2914.3 79735.25
graded stone aggregate (size range 53 mm to
0.075 mm ) to wet mix macadam (WMM)
specification including premixing the material
with water at OMC in for all leads & lifts, laying
in uniform layers with mechanical paver
finisher in sub- base / base course on well
prepared surface and compacting with
vibratory roller of 8 to 10 tonne capacity to
achieve the desired density, complete as per
specifications and directions of Engineer-in-
17.0 SANITARY INSTALLATIONS
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
17.1S General
Providing and fixing white vitreous china
pedestal type water closet (European type
W.C. pan) with seat and lid, 10 litre low level
white P.V.C. flushing cistern, including flush
17.2 pipe, with manually controlled device (handle
lever), conforming to IS : 7231, with all fittings
and fixtures complete, including cutting and
making good the walls and floors wherever
17.2.1 W.C. pan with ISI marked white solid plastic Each 13 6515.55 84702.15
Providing and fixing wash basin with C.I.
brackets, 15 mm C.P. brass pillar taps, 32 mm
17.7 C.P. brass waste of standard pattern, including
painting of fittings and brackets, cutting and
making good the walls wherever require:
17.7.2 White Vitreous China Wash basin size 630x450 Each 14 2226.35 31168.9
mm with a single 15 mm C.P. brass pillar tap
Providing and fixing Stainless Steel A ISI 304
(18/8) kitchen sink as per IS:13983 with C.I.
brackets and stainless steel plug 40 mm,
including painting of fittings and brackets,
cutting and making good the walls wherever
17.10.1 Kitchen sink with drain board
17.16A Providing and fixing 8 mm dia C.P. / S.S. Jet Each 33 349.15 11521.95
with flexible tube upto 1 metre long with S.S.
101 triangular plate to European type W.C. of
quality and make as approved by Engineer - in
Providing and fixing P.V.C. low level flushing
cistern with manually controlled device
(handle lever) conforming to IS : 7231, with all
fittings and fixtures complete.
Providing and fixing solid plastic seat with lid
for pedestal type W.C. pan complete :
17.22B Providing and fixing CP Brass Single lever Each 13 6940.75 90229.75
telephonic wall mixer of quality and make as
approved by Engineer in charge.(a) 15 mm
Providing and fixing P.V.C. waste pipe for sink
17.28 or wash basin including P.V.C. waste fittings
17.28.1 Semi rigid pipe
17.28.2 Flexible pipe
17.29 Providing and fixing 100 mm sand cast Iron Each 23 53.25 1224.75
grating for gully trap.
17.30 Providing and fixing in position 25 mm Each 23 55.65 1279.95
108 diameter mosquito proof coupling of approved
municipal design.
17.31 Providing and fixing 600x450 mm bevelled Each 22 1607.95 35374.9
edge mirror of superior glass (of approved
109 quality) complete with 6 mm thick hard board
ground fixed to wooden cleats with C.P. brass
screws and washers complete.
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
Providing and fixing mirror of superior glass (of
approved quality) and of required shape and
17.32 size with plastic moulded frame of approved
make and shade with 6 mm thick hard board
shelf with edges round off, supported on
anodised aluminium angle frame with C.P.
brass brackets and guard rail complete fixed
with 40 mm long screws, rawl plugs etc.,
17.34 Providing and fixing toilet paper holder :
17.72 Providing and fixing PTMT towel ring Each 23 231.95 5334.85
trapezoidal shape 215 mm long, 200 mm wide
with minimum distances of 37 mm from wall
face with concealed fittings arrangement of
approved quality and colour, weighing not less
Providing and fixing PTMT towel rail complete
with brackets fixed to wooden cleats with CP
brass screws with concealed fittings
arrangement of approved quality and colour.
17.73.2 600 mm long towel rail with total length of 645 Each 22 708.95 15596.9
114 mm, width 78 mm and effective height of 88
mm, weighing not less than 190 gms.
18.0 WATER SUPPLY
18.7S C.P.V.C. PIPES
Providing and fixing Chlorinated Polyvinyl
Chloride (CPVC) pipes, having thermal stability
for hot & cold water supply, and all CPVC plain
& brass threaded fittings, including fixing the
18.7 pipe with clamps at 1.00 m spacing. This
includes jointing of pipes & fittings with one
step CPVC solvent cement and testing of joints
complete as per direction of Engineer in
Charge. ( Internal work - Exposed on wall )
Providing and fixing Chlorinated Polyvinyl
Chloride (CPVC) pipes, having thermal stability
for hot & cold water supply, including all CPVC
plain & brass threaded fittings and fixing the
pipe with clamps at 1.00 m spacing. This
includes jointing of pipes & fittings with one
step CPVC solvent cement and the cost of
cutting chases and making good the same
including testing of joints complete as per
direction of Engineer in Charge. Concealed
work, including cutting chases and making
good the walls etc.
Providing and fixing Chlorinated Polyvinyl
Chloride (CPVC) pipes, having thermal stability
for hot & cold water supply including all CPVC
plain & brass threaded fittings This includes
jointing of pipes & fittings with one step CPVC
solvent cement, trenching, refilling & testing
of joints complete as per direction of Engineer
in Charge. External work
18.15S BRASS FITTINGS
Providing and fixing gun metal gate valve with
C.I. wheel of approved quality (screwed end) :
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
Providing and fixing ball valve (brass) of
18.18 approved quality, High or low pressure, with
plastic floats complete :
Providing and fixing gun metal non- return
valve of approved quality (screwed end) :
18.19.1 25 mm nominal bore
18.19.4 50 mm nominal bore
Providing and fixing uplasticised PVC
connection pipe with brass unions :
18.21.2 45 cm length
Providing and fixing C.P. brass shower rose
with 15 or 20 mm inlet
C.I. SLUICE VALVES/ FIRE HYDRANTS &
18.48 Providing and placing on terrace (at all floor Per 1900 11 20900
levels) polyethylene water storage tank, IS : Litre
12701 marked, with cover and suitable locking
arrangement and making necessary holes for
inlet, outlet and overflow pipes but without
fittings and the base support for tank.
18.49S C.P. BRASS FITTINGS
Providing and fixing C.P. brass bib cock of
approved quality conforming to IS:8931 :
Providing and fixing C.P. brass long nose bib
cock of approved quality conforming to IS
standards and weighing not less than 810
Providing and fixing C.P. brass long body bib
cock of approved quality conforming to IS
standards and weighing not less than 690
Providing and fixing C.P. brass stop cock
18.52 (concealed) of standard design and of
approved make conforming to IS:8931.
Providing and fixing C.P. brass angle valve for
18.53 basin mixer and geyser points of approved
quality conforming to IS:8931
18.53A Providing and fixing C.P. Brass extension Each 26 74.8 1944.8
nipple (size 15mmx50mm) of approved make
and quality as per direction of Engineer-in-
18.59S AIR VALVE & WATER METER (BULK TYPE)
18.65 Providing and fixing PTMT soap Dish Holder Each 27.04 111.45 3013.61
having length of 138mm, breadth 102mm,
137 height of 75mm with concealed fitting
arrangements, weighing not less than 106
CHENNAI DIVISION-ENGINEERING/SOUTHERN RLY
21.0 ALUMINIUM WORK
21.1S General
Filling the gap in between aluminium/ stone/
wood frame and adjacent RCC/Brick/ Stone/
wood/ Ceramic/ Gypsum work by providing
weather/structural non sag elastomeric PU
sealant over backer rod of approved quality as
per architectural drawings and direction of
Engineer-in-charge complete, complying to
ASTM C920, DIN 18540-F & ISO 11600
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
NEFTForm.pdf
ATTACHMENT
ProcedureforLCModeofPayment.pdf
ATTACHMENT
GCCApril2022_compressed.pdf
ATTACHMENT
MOVEMENTOFVEHICLESNEARRAILWAYTRACK.pdf
ATTACHMENT
IRGCCACS1to11_compressed.pdf
ATTACHMENT
FORMATIONBUILDINGBRIDGEPWAYWORKSJULY2024_1.pdf
ATTACHMENT
eTenderformApril2022.pdf
ATTACHMENT
Download all tender documents and submit your bid