Strengthening and improvement of Building Nos. 21, 18/1, 18/2, 11/1 and 11/2 along with other miscellaneous works in North Colony under ADEN/Settlement/GRC, South Eastern Railway, Garden Reach.

A-Execution of work under CPWD DSR2023 with all correction slips up-

B-Non-Schedule item including 18% GST 8857198.89 Below/P

C-Electrical item including 18% GST 11722545.74 Below/P

D-Execution of work covered under CPWD Horticulture 2020 ver-2 with

including @ 18% GST

Civil work for strengthening and improvement of Building No. 21 and 18/1, 18/2, 11/1 and 11/2

along with other miscellaneous works as per CPWD DSR 2023.

S No. Item No Description of Item Unit Qty Rate Amount

2.0 EARTH WORK

2.1S General

Earth work in excavation by mechanical

means (Hydraulic excavator)/manual

means over areas (exceeding 30 cm in

2.6 depth, 1.5 m in width as well as 10 sqm on

plan) including getting out and disposal of

excavated earth lead upto 50 m and for all

lift, as directed by Engineer-in-charge.

2.27 Supplying and filling in plinth with sand cum 6 2123.75 12742.5

2 under floors, including watering, ramming,

consolidating and dressing complete.

5.0 REINFORCEMENT CEMENT CONCRETE

5.12S PRE-CAST RCC

5.12 Providing, hoisting and fixing above plinth cum 19 10585.9 201132.1

level up to floor five level precast

reinforced cement concrete work in string

courses, bands, copings, bed plates,

anchor blocks, plain window sills and the

like, including the cost of required

centering, shuttering but , excluding cost

of reinforcement with 1:1.5:3 (1 cement :

1.5 coarse sand (zone-III) derived from

natural sources : 3 graded stone

aggregate 20 mm nominal size derived

from natural sources).

5.22S STEEL REINFORCEMENT

Steel reinforcement for R.C.C. work

including straightening, cutting, bending,

placing in position and binding all

complete above plinth level.

5.22A.6 Thermo-Mechanically Treated bars of Kg 5765 107.85 621755.25

grade Fe-500D or more.

6.0 MASONRY WORK

6.1S General

Brick work with common burnt clay

6.2 modular bricks of class designation 7.5 in

foundation and plinth in:

8.0 CLADDING WORK

8.1S General

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

Providing and fixing 18 mm thick gang

saw cut, mirror polished, premoulded and

prepolished, machine cut for kitchen

platforms, vanity counters, window sills,

facias and similar locations of required

size, approved shade, colour and texture

8.2 laid over 20 mm thick base cement mortar

1:4 (1 cement : 4 coarse sand), joints

treated with white cement, mixed with

matching pigment, epoxy touch ups,

including rubbing, curing, moulding and

polishing to edges to give high gloss finish

etc. complete at all levels

Granite stone slab colour black,

Cherry/Ruby red

Providing edge moulding to 18 mm thick

marble stone counters, Vanities etc.,

8.3 including machine polishing to edge to

give high gloss finish etc. complete as per

design approved by Engineer-in-Charge.

8.20S STONE WORK DRY CLADDING

8.31 Providing and fixing Ist quality ceramic Sqm 800 1267.95 1014360

glazed wall tiles conforming to IS: 15622

(thickness to be specified by the

manufacturer), of approved make, in all

colours, shades except burgundy, bottle

green, black of any size as approved by

9 Engineer-in-Charge, in skirting, risers of

steps and dados, over 12 mm thick bed of

cement mortar 1:3 (1 cement : 3 coarse

sand) and jointing with grey cement slurry

@ 3.3kg per sqm, including pointing in

white cement mixed with pigment of

matching shade complete.

9.0 WOOD AND P.V.C. WORK

9.1S FRAMES AND TRUSSES

Providing and fixing panelling or panelling

and glazing in panelled or panelled and

glazed shutters for doors, windows and

clerestory windows (Area of opening for

panel inserts excluding portion inside

grooves or rebates to be measured).

Panelling for panelled or panelled and

glazed shutters 25 mm to 40 mm thick :

9.7.7 Float glass panes

9.7.7.1 4 mm thick glass pane (weight not less Sqm 650 2241.8 1457170

than 10kg/sqm).

9.40S MISCELLANEOUS-WOOD WORK

Providing and fixing M.S. grills of required

pattern in frames of windows etc. with

9.48 M.S. flats, square or round bars etc.

including priming coat with approved steel

primer all complete.

9.48.2 Fixed to openings /wooden frames with Kg 8000 238.35 1906800

rawl plugs screws etc.

9.105S GYPSUM BOARD PARTITIONS

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

Providing and fixing factory made uPVC

glazed/wire mesh windows/ doors

comprising of lead free uPVC multi-

chambered frame, sash and

mullion/coupler (where ever required)

extruded profiles having minimum wall

thickness of 1.70 mm for Series R1 and R2

profiles and 2.10 mm for Series R3 and R4

profiles conforming to EN: 12608 in any

shape, colour and design duly reinforced

with galvanized mild steel section made of

required shape & size as per CPWD

Specification, uPVC extruded glazing

beads, interlocks and Inline sash adaptor

(where ever required) of appropriate

dimension, EPDM gasket, hardware, SS

304 grade fasteners of minimum 8 mm dia

with countersunk head, comprising of

matching polyamide PA6 grade sleeve for

fixing frame to finished wall as per IS 1367

: Part 1 to 14, plastic packers, plastic caps

and necessary stainless steel screws etc.

Profile of frame, sash & mullion (if

required) shall be mitred cut and fusion

welded/mechanically jointed duly sealed

at all corners, including drilling of holes for

fixing hardware and drainage of water etc.

After fixing frame the gap between frame

and adjacent finished wall shall be filled

with weather proof silicon sealant over

backer rod of approved size and quality,

all complete as per approved drawing

conforming to CPWD specification &

direction of Engineer-in-Charge. Section of

steel reinforcement and cross sections of

uPVC profiles to be as per design

approved by Engineer-in-Charge. Wire

mesh / Glazing of plain/ toughened/

laminated/ double glass unit with / without

high performance coatings as per design

requirements and conforming to IS: 3548

& IS: 16231 shall be paid separately.

Three track three panels sliding window

with two glazed & one wire mesh panels

with Aluminium channel for roller track,

wool pile, nylon rollers with SS 304 body.

above) x (40 mm & above) & both glazed

and fly screen sash (30 mm & above) x

12 (55 mm & above) with zinc alloy (zamak)

powder coated handle on every glazed

panel along with multi-point locking

system. (Height upto 1.8m)

10.0 STEEL WORK

10.1S General

Steel work welded in built up sections/

framed work, including cutting, hoisting,

10.25 fixing in position and applying a priming

coat of approved steel primer using

structural steel etc. as required.

10.25.2 In gratings, frames, guard bar, ladder, Kg 27500 172.6 4746500

railings, brackets, gates and similar works

11.0 FLOORING

11.1S General

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

Cement concrete flooring 1:2:4 (1 cement

: 2 coarse sand : 4 graded stone

aggregate) finished with a floating coat of

neat cement, including cement slurry, but

excluding the cost of nosing of steps etc.

stone aggregate

11.37S CERAMIC GLAZED TILES

11.37 Providing and laying Ceramic glazed floor Sqm 800 1096.55 877240

tiles of size 300x300 mm (thickness to be

specified by the manufacturer) of 1st

quality conforming to IS : 15622 of

approved make in colours such as White,

15 Ivory, Grey, Fume Red Brown, laid on 20

mm thick cement mortar 1:4 (1 Cement : 4

Coarse sand), Jointing with grey cement

slurry @ 3.3 kg/sqm including pointing the

joints with white cement and matching

pigment etc., complete.

11.41S VITRIFIED FLOOR TILES

Providing and laying vitrified floor tiles in

different sizes (thickness to be specified

by the manufacturer) with water

absorption less than 0.08% and

conforming to IS: 15622, of approved

11.41 make, in all colours and shades, laid on

20mm thick cement mortar 1:4 (1 cement

: 4 coarse sand), jointing with grey cement

slurry @ 3.3 kg/ sqm including grouting

the joints with white cement and matching

pigments etc., complete.

12.0 ROOFING

12.37S RAIN WATER SPOUT AND PIPE

Providing and fixing on wall face

unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including

jointing with seal ring conforming to IS :

5382, leaving 10 mm gap for thermal

expansion, (i) Single socketed pipes.

13.0 FINISHING

13.4S CEMENT PLASTER (IN COARSE SAND)

15 mm cement plaster on rough side of

single or half brick wall of mix:

13.44S EXTERIOR FINISHING

Finishing with Deluxe Multi surface paint

system for interiors and exteriors using

Primer as per manufacturers specifications

13.48.1 Two or more coats applied on walls @ 1.25 Sqm 14900 193.7 2886130

19 ltr/10 sqm over and including one coat of

Special primer applied @ 0.75 ltr /10 sqm

Painting with synthetic enamel paint of

13.61 approved brand and manufacture to give

an even shade :

13.80 Providing and applying white cement Sqm 1530 156.05 238756.5

based putty of average thickness 1 mm, of

21 approved brand and manufacturer, over

the plastered wall surface to prepare the

surface even and smooth complete.

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

Distempering with 1st quality acrylic

distemper, having VOC (Volatile Organic

Compound ) content less than 50 grams/

13.81 litre, of approved brand and manufacture,

including applying additional coats

wherever required, to achieve even shade

Applying priming coats with primer of

approved brand and manufacture, having

low VOC (Volatile Organic Compound )

13.85.3 With water thinnable cement primer on Sqm 16000 73.95 1183200

23 wall surface having VOC content less than

14.0 REPAIRS TO BUILDING

14.72S FINISHING

14.72 Providing and fixing double scaffolding Sqm 1000 338.25 338250

system (cup lock type) on the exterior

side, up to seven story height made with

40 mm dia M.S. tube 1.5 m centre to

centre, horizontal & vertical tubes joining

with cup & lock system with M.S. tubes,

M.S. tube challies, M.S. clamps and M.S.

staircase system in the scaffolding for

working platform etc. and maintaining it in

a serviceable condition for the required

duration as approved and removing it

there after. The scaffolding system shall

be stiffened with bracings, runners,

connection with the building etc wherever

required for inspection of work at required

locations with essential safety features for

the workmen etc. complete as per

directions and approval of Engineer-in-

charge .The elevational area of the

scaffolding shall be measured for payment

purpose .The payment will be made once

irrespective of duration of scaffolding.

15.0 DISMANTLING AND DEMOLISHING

15.1S General

Demolishing cement concrete manually/

by mechanical means including disposal of

material within 50 metres lead as per

direction of Engineer - in - charge.

(including equivalent design mix)

Dismantling doors, windows and clerestory

windows (steel or wood) shutter including

15.12 chowkhats, architrave, holdfasts etc.

complete and stacking within 50 metres

Dismantling precast concrete or stone

15.40 slabs in walls, partition walls etc. including

stacking within 50 metres lead :

15.56 Dismantling old plaster or skirting raking Sqm 330 54.65 18034.5

out joints and cleaning the surface for

plaster including disposal of rubbish to the

dumping ground within 50 metres lead.

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

15.60 Disposal of building rubbish / malba / cum 160 263.95 42232

similar unserviceable, dismantled or waste

materials by mechanical means, including

loading, transporting, unloading to

approved municipal dumping ground or as

approved by Engineer-in-charge, beyond

50 m initial lead, for all leads including all

lifts involved.

16.0 ROAD WORK

16.49S MISCELLANEOUS

16.68 Providing and laying 60mm thick factory Sqm 600 972 583200

made cement concrete interlocking paver

block of M -30 grade made by block

making machine with strong vibratory

compaction, of approved size, design &

shape, laid in required colour and pattern

over and including 50mm thick compacted

bed of coarse sand, filling the joints with

line sand etc. all complete as per the

direction of Engineer-in-charge.

18.0 WATER SUPPLY

18.7S C.P.V.C. PIPES

Providing and fixing G.I. pipes complete

with G.I. fittings and clamps, including

cutting and making good the walls etc. (

Internal work - Exposed on wall )

Providing and fixing G.I. Pipes complete

with G.I. fittings and clamps, including

making good the walls etc. concealed

pipe, including painting with anti corrosive

bitumastic paint, cutting chases and

making good the wall :

22.0 WATER PROOFING

22.1S General

Grading roof for water proofing treatment

22.22A Providing and applying fibre reinforced Sqm 1400 563.1 788340

elastomeric liquid water proofing

membrane with resilient acrylic polymers

having Sun Reflectivity Index (SRI) of 105

on top of concrete roof in three coats

@10.76 litre/ 10 sqm. One coat of self-

priming of elastomeric water proofing

liquid (dilution with water in the ratio of

36 3:1) and two coats of undiluted

elastomeric water proofing liquid (dry film

thickness of complete application/system

not less than 500 microns). The operation

shall be carried out after scrapping and

properly cleaning the surface to remove

loose particles with wire brushes,

complete in all respect as per the direction

of Engineer-in-Charge.

26.0 NEW TECHNOLOGIES AND MATERIALS

26.28S REPAIR AND REHABILITATION ITEMS

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

Chipping of unsound/weak concrete

material from slabs, beams, columns etc.

with manual Chisel and/ or by standard

power driven percussion type or of

approved make including tapering of all

26.28 edges, making square shoulders of

cavities including cleaning the exposed

concrete surface and reinforcement with

wire brushes etc. and disposal of debris

for all lead and lifts all complete as per

direction of Engineer-In-Charge

Cleaning of reinforcement from rust from

the reinforcing bars to give it a total rust

f r e e steel surface by using alkaline

chemical rust remover of approved make

with paint brush and removing loose

particles after 24 hours of its application

with wire brush and thoroughly washing

with water and allowing it to dry, all

complete as per direction of Engineer-In-

Drilling suitable holes in reinforced or

plain cement concrete with power driven

drill machine to a minimum depth of 100

mm upto 200 mm in RCC beams, lintels,

columns and slabs to introduce steel bars

26.30 for sunshades/balconies including fixing

the steel bars in position using epoxy resin

anchor grout of approved make but

excluding the cost of reinforcement, all

complete as per direction of Engineer-In-

Providing, mixing and applying bonding

coat of approved adhesive on chipped

26.31 portion of RCC as per specifications and

direction of Engineer-In-charge complete

in all respect.

26.31.2 Epoxy bonding adhesive having coverage Sqm 400 285.2 114080

2.20 sqm/kg of approved make

Schedule Schedule B-Non-Schedule item including 18% GST

Civil work for Non-Schedule items including @ 18% GST for strengthening and improvement of

Building No. 21 and 18/1, 18/2, 11/1 and 11/2 along with other miscellaneous works.

S No. Item No Description of Item Unit Qty Rate Amount

1 1 Supplying and fixing of 02 way CP Bib cock Each 78.00 2038.47 159000.66

w i t h w a l l flange of Jaquar m a d e baring

m o d e l no. QQT-7041 or similar made

approved by Engineer in Charge. Rate

including GST @ 18%.

commode i.e., rimless single piece - WC

with UF soft close seat cover, hinges, fixing

accessories set, cistern fittings, *P trap -

180mm, size 365 x 655 x 765mm of Jaquar

made bearing model no. LYS- WHT 38851

P or similar approved b y Engineer in

Charge. Rate including GST @ 18%.

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

3 3 Supplying and fixing Hand Shower (Health Each 78.00 1341.02 104599.56

Faucet) ( A B S Body) with 8mm Dia, 1.2

Meter Long Flexible Tube & Wall Hook out

Jaquaf made bearing model no. ALD-CHR-

5 7 3 N o r s i m i l a r m a d e a p p r o v e d by

Engineer in Charge. Rate including GST @

4 4 Supplying and fixing Toilet Rail Holder with Each 78.00 1447.78 112926.84

Fla p o f Jaquar made bearing model no.

AKP-35753P oi similar made appro ved by

Engineer in Charge.Rate including GST @

5 5 Supplying and fixing Towel Ring Round of Each 78.00 1046.18 81602.04

Jaguar made bearing model no. AQN-7721

o r similar made approved b y Engineer in

Charge. Rate including GST @ 18%.

6 6 Supplying and fixing full taughened glass Sqm 78.00 5622.33 438541.74

12mm thick unbreakable (Modi Guard or

similar) i n window/Door with revolving /

sliding mechanism as per direction of

Engineer-in- charge or h i s representative

at site w i t h s u p e r i o r q u a l i t y locking

arrangement. The rate is inclusive of

contractor's ladour, fittings, materials,

tools, plants, freight GST a n d a l l other

charges complete . Rate including GST @

Long Without Lower Hangers b u t w ith 3

hooks of Jaquar made bearing model no.

ACN1181FHN or similar made approved by

Engineer in Charge. Rate including GST @

8 8 Providing & fixing of Wash Basin Mode Mid Each 78.00 24123.07 1881599.46

Ocean Model. MO8027), size 32 with PVC

v a n i t y c a b in a le - w a l l h u n g o similar

approved b y Engineer in Charge Rate is

including, Cement, LaDour, Lead Lift

etc.Rate including GST @ 18%.

9 9 Providing & fixing telephonic hand shower Each 78.00 4578.92 357155.76

of Jaquar make HSH 1731 o r similar

approved by Engineer in Charge. Rate

including GST @ 18%

10 10 Providing & fixing spray hose Jaquar code Each 78.00 1772.70 138270.60

n o . CQT-23069 or similar approved by

Engineer in Charge. Rate including GST @

11 11 Providing & fixing bottle trap jaquar code Each 78.00 1846.04 143991.12

n o . ALD 769 or similar approved by

Engineer in Charge. Rate including GST @

12 12 Providing & fixing b a s i n waste coupling Each 78.00 664.88 51860.64

jacquar code No. ALD 709L130 o r similar

approved by Engineer in Charge.Rate

including GST @ 18%

13 13 Providing a n d fi x i n g Decorative Brass Each 78.00 1636.64 127657.92

Handle 250mm long of similar approved by

Engineer in Charge. Rate including GST @

14 14 Providing & fixing Shower rose jaguar code Each 42.00 5329.21 223826.82

n o . O H S 3 5 4 9 7 or similar approved by

Engineer in Charge. Rate including GST @

15 15 Providing & fixing sink mnixure jaquar Each 78.00 4027.91 314176.98

code no. CQT 233098 jaguar code no.CQT

233098 or similar approved by Engineer in

Charge. Rate including GST @ 18%.

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

jaguar code No. CQT23281UPR or similar

approved by Engineer in Charge. Rate

including GST @ 18%.

17 17 Supply and Fixing o f digital print Wall Each 78.00 197.23 15383.94

Paper o f approved pattern and design by

Engineer - i n - Charge. T h e cost included

all materials, Tools and Plants Labour,

lead, lift, ascent, decent Taxes a n d all

other incidental charges complete. Rate

including GST @ 18%.

18 18 Supply of Digital Board Pasted on Acrylic Square 2250.00 921.13 2072542.50

Sheet o f which matter, colour, front, size Foot

and design approved by Engineerin-Charge

and fixing on existing frame.Rate including

19 19 S u p p l y of painted N a m e Board which Square 165.00 2429.87 400928.55

m a t t e r , c o l o u r , f r o n t size and design Foot

approved by Engineer- in-Charge made

w ith chromium plated brass/ steel plate

and fixing on e x i s t i n g frame. Rate

including GST @ 18%.

Schedule Schedule C-Electrical item including 18% GST

Electrical work for strengthening and improvement of Building No. 21 and 18/1, 18/2, 11/1 and 11/2

along with other miscellaneous works.

S No. Item No Description of Item Unit Qty Rate Amount

1 1 Supply and Laying of Single-Phase Point Point 2926.00 706.82 2068155.32

Wiring (includes Phase, Neutral and

Protective Earth wire) from Modular Switch

Board to equipment's (light, Ceiling fan,

Exhaust Fan, calling bell etc.) ceiling rose

through wall concealed PVC conduit of size

25sq mm or more. Modular Switch Board,

modular switch, wiring, PVC conduit, wall

cutting, wall refilling/finishing, Ceiling rose,

copper lugs for termination etc. are

inclusive in the point wiring. Wiring shall

be done by cutting of the wall to

accommodate PVC conduit, utilizing of

proper bends wherever required, re-fill

and re-finish the wall as like original by

plastering and painting after wiring. Size

of Phase, Neutral and Protective earth wire

shall be 1.5sqmm, 1.5 sqmm & 2.5 sq mm

respectively. Socket of 6 A, if required,

shall be provided in the modular board

and shall be considered as half point. The

detailed specification of different

component of point wiring is provided in

explanatory note.

2 2 Supply of Modular Switch Board flush type Point 1254.00 234.82 294464.28

with GI Enclosure & Cover made of tough

non-ignitable insulating material with 01

no Modular Switch of 16A (IS:3854/1997)

and 01 no Modular Socket 6Pin 16/6A(IS

1293-2019). The detailed specification of

different component is provided in

explanatory note.

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

3 3 Fixing and commissioning of switch socket Point 1254.00 11.80 14797.20

board (Power) as above (Item No.-2)

includes wall cutting to accommodate &

flush the modular switch board GI

enclosure with modular type switch and

socket, all the wire connection and

termination with properly crimped Lugs

and connector (copper) and re-filling and

re-finishing the wall as like original by

plastering and painting after fixation of

modular board. This work shall follow the

code of IS 732 (1989).The earthing

connection work shall follow the code of

practice as per IS 3043 (1987).

4 4 Supply and Laying of main service/sub- Metre 12500.00 95.58 1194750.00

service line Single Phase (includes Phase,

Neutral and Protective Earth wires, each

2.5 sqmm) through wall concealed PVC

conduit of size 25sq mm or more. Wiring

shall be done by wall cutting to

accommodate PVC conduit, utilizing of

proper bends wherever required, re-fill

and re-finish the wall as like original by

plastering and painting after wiring. All the

connection/termination shall be done with

properly crimped Lugs and connector (

copper) as per site requirement Rate per

Mtr. shall means supply and laying of 1

Mtr. phase wire, 1 Mtr. neutral wire, 1Mtr.

earth wire through 1 Mtr. PVC conduit and

1 mtr wall cutting to accommodate the

whole wiring and re-fill and re-finish the

wall as like original by plastering and

painting after wiring] . The detailed

specification of different component is

provided in explanatory note.

5 5 Supply and Laying of main service/sub- Metre 6000.00 172.28 1033680.00

service line Single Phase (includes Phase,

Neutral and Protective Earth wires, each

4.0 sqmm) through wall concealed PVC

conduit of size 25sq mm or more. Wiring

shall be done by wall cutting to

accommodate PVC conduit, utilizing of

proper bends wherever required, re-fill

and re-finish the wall as like original by

plastering and painting after wiring. All the

connection/termination shall be done with

properly crimped Lugs and connector (

copper) as per site requirement Rate per

Mtr. shall means supply and laying of 1

Mtr. phase wire, 1 Mtr. neutral wire, 1Mtr.

earth wire through 1 Mtr. PVC conduit and

1 mtr wall cutting to accommodate the

whole wiring and re-fill and re-finish the

wall as like original by plastering and

painting after wiring] . The detailed

specification of different component is

provided in explanatory note.

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

6 6 Supply and Laying of main service/sub- Metre 2000.00 326.86 653720.00

service line Single Phase (includes Phase,

Neutral each-1.5 sqmm and Protective

Earth wires 2.5 sqmm) through heavy duty

rigid GI Steel Conduit Pipe as per IS: 14927

(Pt.II)/latest/IS: 9537 (Pt.III)/latest etc.

Wiring shall be done fixing GI Steel

Conduit Pipe , utilizing of proper bends

wherever required, using stainless steel

screw or saddle. All the connection/

termination shall be done with properly

crimped Lugs and connector (copper) as

per site requirement Rate per Mtr. shall

means supply and laying of 1 Mtr. phase

wire, 1 Mtr. neutral wire, 1Mtr. earth wire

through 1 Mtr. GI Steel Conduit Pipe and

fixation] . The detailed specification of

different component is provided in

explanatory note.

7 7 Supply and Laying of main service/sub- Metre 1000.00 428.34 428340.00

service line Single Phase (includes Phase,

Neutral and Protective Earth wires, each

4.0sqmm) through heavy duty rigid GI

Steel Conduit Pipe as per IS: 14927

(Pt.II)/latest/IS: 9537 (Pt.III)/latest etc.

Wiring shall be done fixing GI Steel

Conduit Pipe , utilizing of proper bends

wherever required, using stainless steel

screw or saddle. All the connection/

termination shall be done with properly

crimped Lugs and connector ( copper) as

per site requirement Rate per Mtr. shall

means supply and laying of 1 Mtr. phase

wire, 1 Mtr. neutral wire, 1Mtr. earth wire

through 1 Mtr. GI Steel Conduit Pipe and

fixation] . The detailed specification of

different component is provided in

explanatory note.

8 8 Supply , fixing and commissioning of 20A Each 307.00 243.08 74625.56

,4 module Power Unit comprises 20A

Starter (ISI marked, rated voltage 220V

AC, rated current:20 Amps, conforming to

IS/IEC 60898-1:2015 (Reaffirmed

Year:2024) or latest, , Un adjustable time

current characteristics and suitable for use

in protection of industrial, commercial and

domestic electrical installations) , 16A

socket& additional 16A plug. Suitable to

operate AC supply 230v/50 Hz with GI

Enclosure confirms to IS 14772 including

internal wiring with PVC insulated 4.0

Sq.mm. 1100V grade, single core,

multistranded FR-LSH copper conductor.

Modular board Cover shall be made of

tough Non- Ignitable insulating material,

material of base -vitrified ceramic,

Conforming to IS : 1293-2019, Amendment

no. 1 or latest with ISI mark. Fixing and

commissioning shall be done concealed in

the wall along with termination

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

9 9 Supply of LED wall light / Bracket light Each 328.00 434.24 142430.72

fitting with 7W lamp 5 star rated energy

efficient (white/ warm white) compliance

to IS 1602 (part 1):2012 efficiency

minimum 130 Lm/watt, suitable for

230V,50Hz, AC, aluminum die cast with

brushed nickel finish material and opal

glass diffuser with supply of installation

fittings. Before supply of the materials the

drawing/ design / technical datasheet/

make and model should be submitted by

firm for prior approval.

10 10 Fixing and commissioning of LED wall light Each 328.00 43.66 14320.48

/ Bracket light fitting with 7W lamp as

above (Item No.-09). Fixing shall be done

using GI/SS Fastners, screw etc. as per

standard manner and necessary

connection to be done with 1.5 sq. mm,

Copper Conductor (flexible), as phase and

neutral and continuous earth/ protective

conductor of 2.5 sq. mm, Copper

Conductor(flexible).The detailed

specification of different component is

provided in explanatory note.

11 11 Supply of 7-Watt LED Light compliance to Each 152.00 2160.58 328408.16

IS:10322 (Part-5/sec 2):2012 for Wall

Picture, Mirror with flexible neck,

aluminum die cast with brushed nickel

finish material, Warm White 3000K, with

good Color rendering (CRI>80), suitable to

operate 230V, AC supply, inbuilt surge

protection, efficiency minimum 130

Lm/watt. Before supply of the materials

the drawing/ design / technical datasheet/

make and model should be submitted by

firm for prior approval.

12 12 Fixing & commissioning of 7-Watt LED Each 152.00 107.38 16321.76

Light as above (Item No.- 11). Fixing shall

be done using GI/SS Fastners, screw etc.

as per standard manner and necessary

connection to be done with 1.5 sq. mm,

Copper Conductor (flexible), as phase and

neutral and continuous earth/ protective

conductor of 2.5 sq. mm, Copper

Conductor(flexible).The detailed

specification of different component is

provided in explanatory note.

13 13 Supply of Golden Antique design double Each 296.00 1898.62 561991.52

bracket wall lamp fitting with glass cover

with 2 no 7W energy efficient 5 star LED

lamp (white/ warm white) compliance to IS

1602 (part 1):2012 efficiency minimum

130 Lm/watt, suitable for 230V,50Hz, AC,

aluminum die cast with brushed nickel

finish material and opal glass diffuser with

supply of installation fittings. Before

supply of the materials the drawing/

design / technical datasheet/ make and

model should be submitted by firm for

prior approval.

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

14 14 Fixing and commissioning of LED wall light Each 296.00 94.40 27942.40

/ Bracket light fitting with 7W lamps as

above (Item No.-13). Fixing shall be done

using GI/SS Fastners, screw etc. as per

standard manner and necessary

connection to be done with 1.5 sq. mm,

Copper Conductor (flexible), as phase and

neutral and continuous earth/ protective

conductor of 2.5 sq. mm, Copper

Conductor(flexible).The detailed

specification of different component is

provided in explanatory note.

15 15 Fixing and commissioning of LED Batten Numbers 560.00 15.34 8590.40

18 watt (will be supplied by railway) as

standard manner using GI/SS screw (if

required) and necessary connection to be

done with 1.5 sq. mm, Copper Conductor

(flexible), as phase and neutral and

continuous earth/ protective wire of 2.5

sq. mm, Copper Conductor(flexible).The

detailed specification of different

component is provided in explanatory

16 16 Fixing and commissioning of BLDC Fan Each 373.00 130.98 48855.54

1400mm sweep (supplied from Railway

side) ,inclusive of supply and fixing of

BLDC fan regulator and other requisite

materials as per site requirement and

necessary connection to be done with 1.5

sq. mm, Copper Conductor (flexible), as

phase and neutral and continuous earth/

protective conductor of 2.5 sq. mm,

Copper Conductor(flexible).The detailed

specification of different component is

provided in explanatory note.

17 17 Supply of Electric Chimney of wall Each 40.00 13430.76 537230.40

mounted type, with Auto-Clean feature, 60

cm having minimum Air Suction Capacity

of 1400 m3/hr. with 5 star BLDC Motor and

Motion Sensor Touch controls [for chimney

operation with movement of the hand], for

working at single phase 230 V± 10%,

50Hz AC Supply, including Flexible

Aluminum Duct Pipe with Cowl (diameter-

6") for exhaust having length of 10ft.

Material of Chimney shall be of Stainless

Steel of grade 304, filter-less technology

[ensures higher airflow and lower

maintenance], Stainless Steel oil collector

tray, Turbo Exhaust mode [in this mode

the chimney will run on the highest speed

and in case of any blockage in the system

the same will be removed], with Safety as

per IS:302 Part 1: 2008 or latest with all

required GI/SS nut, bolt and all other

materials to complete the work in all

respect as per direction site In Charge.

18 18 Fixing & commissioning of Kitchen Each 40.00 671.42 26856.80

Chimney as above (Item No.- 17) as per

direction site in-charge and if any

termination required same should be done

with properly crimped Lugs and connector

(copper) as per site requirement and

fixation of Kitchen Chimney and Exhaust

Duct pipe shall be done with suitable GI/SS

fastener, Clamp, Wooden support,

nut/bolts etc. As per site requirement and

as advised by consignee.

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

star BLDC Motor, 1300 RPM, Silent

operation high air delivery of minimum

1150 CMPH with ISI marked, having Self

closing damper compatible with exhaust

fan, suitable for 230V,50Hz, AC supply,

with other requisite accessories etc.

20 20 Fixing and commissioning of Exhaust Fan Each 184.00 129.80 23883.20

(250mm) as above (Item No.- 19) and

necessary connection to be done with 1.5

sq. mm, Copper Conductor (flexible), as

phase and neutral and continuous earth/

protective conductor of 2.5 sq. mm,

Copper Conductor(flexible).The detailed

specification of different component is

provided in explanatory note.

21 21 Supply of Stationary Storage Type Electric Each 112.00 7299.48 817541.76

Water Heater (Geyser) of 25 Ltrs Capacity

Conforming to IS:2082: 2018, amendment

no. 1 and with latest

amendments/revisions with ISI mark, BEE

star rating 5, Closed type as per clause

3.102 of IS 302-2-21: 2018 or latest, with

Stainless steel panel for Vertical wall

mounting of Water Heater. Material of

Inner Container & Body of Water Tank

shall be of Stainless Steel of grades 304,

304L, 316, 316L as per IS 1570 (Part

5):1985 (Reaffirmed 2018) or latest.

Insulation in-between Outer SS Body &

inner SS Container shall be of Fire

retardant type. Finish as per clause 21.1 of

IS 2082. Anode Rod (also called Sacrificial

rod) shall be provided in addition to Heater

element. Water Heater shall be of Class I

type as per IS 302-2-21 clause 6.1 with

double insulation or reinforced insulation,

Water Heater shall be for Indoor

Installation with at least IP-X1. Pressure

relief device shall be provided in the Water

Heater. Instruction for operation of

Pressure Relief Device as per clause 7.12

(b) of IS 302-2-21 shall be provided with

the material as well as marked on Water

Heater such that it is visible in normal use.

Leakage current for Water Heater shall not

exceed 0.21 mA per KW or 1.5 mA

whichever is lesser.

22 22 Fixing ,commissioning and testing of Each 112.00 364.62 40837.44

geyser as above (Item No.21) using

stainless steel Fastners/ screw and clamp

as per direction of railway representative.

23 23 Supply of 4 way double door PPI DB, wall Numbers 40.00 6468.76 258750.40

mounted type, made of CRCA Sheet Steel,

double door, powder coated confirms to IS

protection, complete with insulated TP

copper busbar with earth terminal, neutral

link ,interconnecting wires (colour coded),

cable ties & blanking plates and suitable

for MCB incomer , Cu Bus bar conforms to

IS:613/latest & 2826/latest and all other

items as per relevant standard

specifications.

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

24 24 Fixing and commissioning of 4 way double Numbers 40.00 323.32 12932.80

door PPI DB as mentioned at item no 23,

along with installation of MCCB/MCB as

per site requirement and direction of

railway authority (MCCB/MCB will be

provided from railway store).Its connection

and installation with incoming & outgoing

cables/wires with necessary termination

with cable/wires glands/Lugs/ Bimetallic

Lugs terminal etc. with proper crimping as

per site requirement. After commissioning

thermal test, Earthing testing, tripping test

etc. shall be carried out in the presence of

railway representative with adequate load

(cost for that test shall be borne by the

contractor) and proper labeling (circuit

identification) of the outgoing side and

incoming side switchgear shall be done by

pasting sticker. Dressing of wire shall be

done as per code of IS 732. The earthing

connection work shall follow the code of

practice as per IS 3043 (1987).DB fixation

shall be done by cutting the wall to

accommodate the DB wall flushed fixation,

plastering & leveling the wall before DB

fixation, fixation of DB with GI/SS

fasteners, refilling/ re-finishing the wall

like original with necessary plastering,

painting as per direction of railway

(CRCA sheet minimum thickness 1.6 mm)

enclosure,ISI marked, Instantaneous

tripping range:B, no. of poles: 4 pole with

4PP (PP=protected pole), rated voltage

415V AC, rated current:63 Amps,

conforming to IS/IEC 60898-1:2015

(Reaffirmed Year:2024) or latest, with

rated short circuit current capacity 10KA,

fixed unadjustable time current

characteristics and suitable for use in

protection of industrial, commercial and

domestic electrical installations. MCBs

shall be suitable for 50 Hz AC main

supplies. MCBs shall have fixing

arrangement for mounting on steel rails of

top Hat section Rail TH:35-7.5 conforming

to IS/IEC 60715:2017 (Reaffirmed

Year:2024) or latest.

26 26 Supply of 6-32A,15kA, SP MCB, ISI marked, Numbers 480.00 214.76 103084.80

Instantaneous tripping range: B curve, No.

of poles: single pole with 1 PP

(PP=Protected pole), rate voltage 240V

AC, rated current: 6-32 Amps, conforming

to IS/IEC 60898-1:2015 (Reaffirmed

Year:2024) or latest, with rated short

circuit current capacity 15 KA, fixed Un

adjustable time current characteristics and

suitable for use in protection of industrial,

commercial & domestic electrical

installation. MCBs shall be suitable for 50

Hz AC main supplies. MCBs shall have

fixing arrangement for mounting on steel

rails of top Hat section Rail TH:35- 7.5

conforming to IS/IEC 60715:2017.

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

27 27 Supply of Type 2 AC Surge protection Numbers 40.00 3347.66 133906.40

device (320V), TPN,20kA, conforms to IEC

61643-21 latest, all other items as per

relevant specifications along with all

relevant accessories. It shall be suitable

for 50 Hz AC main supplies and shall have

fixing arrangement for mounting on steel

rails of top Hat section Rail TH:35-7.5

conforming to IS/IEC 60715:2017.

conforms to IEC61009-1, IS 12640-2, EN

61009-1/latest, and all other items as per

relevant specifications and as per IS

standard along with all relevant

accessories, suitable for use in protection

of industrial, commercial & domestic

electrical installation. It shall be suitable

for 50 Hz AC main supplies and shall have

fixing arrangement for mounting on steel

rails of top Hat section Rail TH:35-7.5

conforming to IS/IEC 60715:2017.

29 29 Supply and laying of 19x6 mm GI strips for Metre 450.00 109.52 49284.00

earthing, clamped to brick wall, cable tray

etc., as required . All the clamps, Fastners,

Screws etc to be used for fixation purpose

shall be made of stainless steel. All the

intermediate joints shall be connected

using clamp and nut bolt arrangement or

properly welding.

30 30 Laying of cable (cable will be supplied by Metre 2500.00 47.20 118000.00

Rly.) in air/wall/wooden structure /cable

tray with supply & fixing of suitable GI/SS

clamp/saddle/fixtures/covers/encasing etc.

(minimum clamping/saddle interval 30cm)

including termination, connection with the

electrical equipment/installations by

suitable gland/socket/lugs/ Bimetallic lugs

etc., testing and commissioning of cables

as per site requirement inclusive of supply

of all requisite materials required for the

same. The location/place and actual

length of laying depends upon the specific

site requirement and as advised by

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

31 31 Supply fixing commissioning of GI Hot Dip Metre 150.00 686.38 102957.00

ladder type cable tray wall mountable of

dimension (width 200 mm, Height 75 mm,

Tray thick ness 2.0 mm) along with two

nos. Coupler Plate and minimum 08 set of

nut-bolts & washers for coupling. The tray

is to be supplied along with all the

required accessories for wall mounting

such as Support brackets, Nut-Bolts,

Washers, Fasteners & Clamps etc. Width

of support bracket shall be minimum 280

mm so that tray can be mounted at a

distance 50mm from wall. The quantity of

Support bracket and associated

accessories should be suitable for

supporting & mounting of Cable-tray at a

distance of 2 Meter or less. Support

brackets, Coupler Plates, Nut-Bolts &

Washers, Fasteners & Clamps etc. shall be

of either Stainless Steel (SS) or Hot-dip

Galvanized Iron (GI). Galvanizing Hot dip

shall be as per IS 2629/4759 for cable tray

and associated accessories. Fixation will

be done as per direction of railway

authorized representative, cost of the

fixation includes all the materials cost as

per standard for fixation of cable tray

hanging from roof/ceiling and wall

32 32 Supply fixing commissioning of GI Hot Dip Metre 230.00 364.62 83862.60

Perforated Type Cable Tray wall

mountable of dimension ( width 150 mm,

Height 50 mm, Tray thick ness 2.0 mm,)

along with two nos. Coupler Plate and

minimum 08 set of nut-bolts & washers for

coupling. The tray is to be supplied along

with all the required accessories for wall

mounting such as Support brackets, Nut-

Bolts, Washers, Fasteners & Clamps etc.

Width of support bracket shall be

minimum 230mm so that tray can be

mounted at a distance 50mm from wall.

The quantity of Support bracket and

associated accessories should be suitable

for supporting & mounting of Cable-tray at

a distance of 2 Meter or less . Support

brackets, Coupler Plates, Nut-Bolts &

Washers, Fasteners & Clamps etc. shall be

of either Stainless Steel (SS) or Hot-dip

Galvanized Iron (GI). Galvanizing Hot dip

shall be as per IS 2629/4759 for cable tray

and associated accessories. Fixation will

be done as per direction of railway

authorized representative, cost of the

fixation includes all the materials cost as

per standard for fixation of cable tray on

wall structure suitable for laying of cable.

33 33 Supply of Earth cone including sump box Each 10.00 1572.94 15729.40

and chemical compound etc as per

CEEGRC'sDrawing no : CEE/G/A3/P-

150,Alt.1 with supply of all requisite items.

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

34 34 Fixing and commissioning of Earth cone Each 10.00 451.94 4519.40

including sump box as above (Item No.-

33) with supply of all requisite items. The

Cost includes excavation of pit either

manual or by machine in any kind of soil,

pit making and making of sump box with

salt, charcoal etc. and construction of RCC

Cover for sump box of minimum

dimension of 1.5ftx1.5ftx1.5 ft. Cost also

includes connection of 8 SWG GI. wires/ GI

strips between earth cone and main

switch/DB/Street light pole/LT /HT panels

etc. as per site supervisor's instruction.

Cost also includes earth clamp of size 50 X

6 mm GI testing of earth resistance jointly

with Railway representative and the earth

value shall be printed on the earth sump

box. The work shall follow the code of

practice as per IS 3043 (1987).

35 35 Dismantling, Removing of existing wiring, Job 72.00 1180.00 84960.00

incoming cable , DB , Junction box and all

the electrical fittings, switch board etc at

each quarter and All released and

dismantled materials to be handed over to

SSE(EL-P/GRC) consignee Store with

Contractor's own labour, transport, load,

36 36 Supply of 18 Way SPN DB with cable end Each 32.00 8567.98 274175.36

box & Blank plates, wall mounted type,

made of CRCA Sheet Steel [Minimum

thickness 1.6mm], IP 54, IK 09, confirms to

door, powder coated complete with earth

terminal, neutral link. Cu Bus bar conforms

to IS:613/latest & 2826/latest and all other

items as per relevant specifications and as

per IS Standard.

37 37 Installation and commissioning of 18 Way Each 32.00 856.68 27413.76

SPN DB as mentioned at item no 36, along

with installation of MCB,SPD and RCBO as

per site requirement and as per direction

of railway authority (MCB/RCBO/SPD will

be provided from railway store).its

connection and installation with incoming

& outgoing cables/wires with necessary

termination with cable/wires glands/Lugs/

Bimetallic Lugs terminal etc. with proper

crimping as per site requirement. After

commissioning thermal test, Earthing

testing, tripping test etc. shall be carried

out in the presence of railway

representative with adequate load (cost

for that test shall be borne by the

contractor) and proper labeling (circuit

identification) of the outgoing side and

incoming side switchgear shall be done by

pasting sticker. Dressing of wire shall be

done as per code of IS 732. The earthing

connection work shall follow the code of

practice as per IS 3043 (1987). DB fixation

shall be done by cutting the wall to

accommodate the DB wall flushed fixation,

plastering & levelling the wall before DB

fixation, fixation of DB with GI/SS

fasteners, re-filling/re-finishing the wall

like original with necessary plastering,

painting asper direction of railway

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

Instantaneous tripping range:B curve, no.

of poles: double pole with 2 PP

(PP=protected pole), rated voltage 240V

AC, rated current: 63 Amps, conforming to

IS/IEC: 60898-1:2015 (Reaffirmed

Year:2024) or latest, with rated short

circuit current capacity 10KA, fixed

unadjustable time current characteristics

and suitable for use in protection of

industrial, commercial and domestic

electrical installations. MCBs shall be

suitable for 50 Hz AC main supplies. MCBs

shall have fixing arrangement for

mounting on steel rails of top Hat section

Rail TH:35-7.5 conforming to IS/IEC

60715:2017 (Reaffirmed Year:2024) or

RCBO, conforms to IEC61009-1, IS 12640-

2, EN 61009-1/latest, and all other items

as per relevant specifications and as per IS

standard along with all relevant

accessories, suitable for use in protection

of industrial, commercial & domestic

electrical installation. It shall be suitable

for 50 Hz AC main supplies and shall have

fixing arrangement for mounting on steel

rails of top Hat section Rail TH:35-7.5

conforming to IS/IEC 60715:2017. with all

relevant accessories.

device (320V), DP,20kA, conforms to IEC

61643-21 latest, all other items as per

relevant specifications along with all

relevant accessories. It shall be suitable

for 50 Hz AC main supplies and shall have

fixing arrangement for mounting on steel

rails of top Hat section Rail TH:35-7.5

conforming to IS/IEC 60715:2017.

Schedule D-Execution of work covered under CPWD Horticulture 2020 ver-2 with all correction slips

up-to-date.Rate including GST @ 18%

Item- 1 Horticulture & Landscaping Works Building No. 21 and 18/1, 18/2, 11/1 and 11/2.

S No. Item No Description of Item Unit Qty Rate Amount

2.0 HORTICUTURE AND LANDSCAPING

2.33 Providing and laying Neelgiri/Mexican Sqm 600 214.4 128640

grass turf with earth 50mm to 60mm

thickness of existing ground prepared with

proper level and ramming with tools

wooden (Dhurmos) and then rolling the

surface with light roller make the surface

smoothen and light waterning with

sprinkler and maintenance for 30 days or

more till the grass establish properly, as

per direction of officer-in-charge

5.0 ORNAMENTAL PLANTS

5.12 Providing and Displaying Bougainvillea Each 60 322.9 19374

named variety, Sobhra, Thima, Marry

palmar, Cherry Blossom etc. well

2 developed with fresh & healthy bushy in

full bloom 75 to 90 cm ht. in 40 cm

Cement Pot as per direction of the officer-

SER-GRC-ENGINEERING/SOUTH EASTERN RLY

5.30 Providing and Displaying Foxtail palm well Each 80 1183.9 94712

developed with fresh & healthy foliage of

ht. 210 to 240 cm in big 40 cm Cement Pot

as per direction of the officer-in-charge.

6.0 GROUND COVERS PLANTS

6.12 Providing and stacking of Duranta Golden, Each 800 20 16000

having ht.15 to 20 cm bushty shape with

4 fresh and healthy leaves in 15 cm size of

Earthen Pot/Plastic Pot & as per direction

of the officer-in-charge.

6.15 Providing and stacking of Ipomea (Golden Each 800 20 16000

leaves),with fresh and healthy leaves in 15

cm size of Earthen Pot/Plastic Pot & as per

direction of the officer-in-charge.

6.25 Providing and stacking of Syngonium Each 200 30 6000

(Butterfly) variegated with 2-3 suckers

6 healthy foliage in Earthen Pot/Plastic Pot

of size 20 cm. as per direction of the

officer-in-charge.

7.0 TREE PLANTS

7.1 Providing and stacking of Acacia Each 400 65 26000

auriculiformis of ht 150-165 cm in bag size

of 25 cm as per direction of the officer-in-

7.11 Providing and stacking of Bottle palm of Each 200 350 70000

ht. 210-240 cm bottom girth 30-35 cm

well developed in big HDPE bags as per

the direction of Officer in charge.

7.27 Providing and stacking of Ficus benjamina Each 80 180 14400

(green) of height 150-165 cm., bushy with

9 healthy branches and lush green foliage in

big size HDPE bags as per direction of the

officer-in-charge.