Maintenance jobs related to Carpentry and PH works at

Amount

Dismantling doors, windows and clear storey Openings (Steel / wood) shutter

Dismantling doors, windows and clear storey Openings (Steel / wood) shutter including frame,chowkhats, architraves, holdfasts etc. complete and stacking designated place within 300 m lead. Of Area 3.00 Sq.M and Below

Dismantling doors, windlows and clearstorey windows (Steel / wood) shutter including frame, chowkhats, architraves, holdfasts etc. complete and stacking designated place within 300m lead. Of Area beyond 3.00 Sq.M

Dismantling/ Taking out doors, windlows and clearstorey openings (Steel / wood) shutter including stacking within 300 m lead( Only Shutters) Of Area 3.00 Sq.M and Below

Dismantling / Taking out doors, windows and clearstory openings (Steel / wood) shutter including stacking within 300 m lead( Only Shutters) Of Area beyond 3.00 Sq.M

Dismantling Aluminium/ Wooden / Gypsum partitions, doors, windows, ventilators, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable materials in designated place within 300 m lead as directed by the Engineer-in-Charge.

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismantling and stacking within 100 m lead.

Dismantling G.I pipes of all diameter external work including excavation and refilling trenches after taking out pipes manually / by mechanical means including stacking of pipes within 100 m lead as per direction of Engineer-in-charge.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 100 m lead For thickness of tiles above 10 mm and up to 25 mm

Resizing & Refixing existing wooden doors for smooth operation. 1. Existing wooden shutter doors shall make floor touch free (to increase bottom clearance) by plane or cutting as approved manner. 2. If need, replacing existing bottom beading patti with new one, minimum 12 mm thick ( wooden beading if replaced wiil be measured under item no. 5.4) 3. The job is involved of dismantling/ taking out existing door shutter, un-screwing of hinges, after plane/fixing wooden beading , re-positioning the door shutter, re-fixing of door closer, handles if any etc. compete as directed by EIC. 4. Providing & fixing necessary wooden screws as required manner in position. 5. Adjustements of hinges if required. ( Hinges if required replacing shall measured in relevant item) 6. Measurements: Each shutter of size of 1000 mm x 2100 mm shall be measured as one job

Resizing of existing aluminium door shutter. 1. Existing aluminium framed swing doors shall make floor touch free (to increase bottom clearance) by resizing 2. The job is involved of dismantling existing shutter totally including accessories/fittings; cutting of aluminium section as required; reassembling. 3. Existing damaged/not reusable aluminium sections shall be replaced with new ones and the same will be measured under concerned items on weight basis. 4. Providing and fixing of s.s. tie rods having suitable nutt/bolts system at both ends of shutter if need. 5. Reshaping and re-fixing of existing board panel/glass sheets as required; 6. Re-erecting and repositioning the shutter as earlier. 7. Re-fixing of all fittings such as pull/push handle; hydraulic door closer; hinges; locking arrangement; tower bolts; 8. Replacing the existing damaged rubber gasket lining and aluminium clips with new ones 9. The contractor shall be provided the sundry materials such as rubber gaskets; screws, ms tie rods, Pivot top piece etc and no extra payment will be made for these. 10. If glass panels are broken during handling, the contractor shall replace the same at no extra cost. 11. Supply, inserting and fixing of hard wooden blocks of 150mm length in hinges, floor spring & door closer area of aluminium sections 11. Measurements: Each shutter up to size of 1000 mm x 2100 mm will be measured as one job

Providing wood work in frames of doors, windows, clear story openings and other frames, wrought framed and fixed in position of required size and shape including sawing, jointing,making rebates for shutters, making grooves as shown in the drawings, finishing the surfaces to the required finish all as per specifications and drawings including necessary MS hold fasts 40 mm X 3 mm thick, 200 mm long / with coach screws including protective painting to the suface that will come in contact with walls, joining materials, labour etc. complete all as per specifications and as directed by the Engineer-in-charge.Using Second class teak wood (Timber to be got approved by the Engineer incharge before manufacturing)

Providing and fixing 35 mm thick flush door shutters conforming to IS : 2202 non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with internal teak wood lipping 25mm wide and fixing with 4 Nos of 125 mm long Stainless steel Hinges with S.S. wood screws complete.

Extra over item no: 5 including supply and installation.

Extra over item no: 5 for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters of thickness35/40mm (over all area of door shutter to be measured Commercial flush door shutters.

Extra over item no: 5 Flush Door Shutters making Rebate for Double Leaf Shutters of all sizes, Thickness and Finishes complete as per the drawings.

Providing and fixing 50 X 20 mm wooden moulded beading to using 2nd class teak wood to door and window frames with iron screws, plugs and priming coat on unexposed surface complete.

Providing edge lipping with 2nd class teak wood battens 40x12 mm minimum depth on all edges of new Commercial flush door shutters. and replace edge lipping as required for existing old wooden shutters for repair works.

Extra for providing and fixing flush doors with decorative veneering on both sides.( Shutter size shall be taken for measurement)

Providing & Fixing / replacing vision panel not exceeding 0.1 sqm in all type of flush door including fixing 4 mm Clear Glass with necessary teak wood/ Aluminium/ms Beadings complete all as per specifications and asdirected by EIC. (Including cost of glass).

Providing and fixing 35mm thick FRP door shutters flush door / panelled type with approved colour or wooden veneer finish of approved make, design & colour. made out of 1.5 mm thick FRP skin moulded over wooden frame work of 40 mm wide and required thickness wooden styles and minimum 100 mm wide lock rails and wooden blocks for door stoppers, tower bolts, baby latch, aldrop, hinges, handles etc. wherever required and core filled with Polyurethane Foam and fixing with 4 Nos 100 mm (ISI marked) heavy quality stainless steel butt hinges with S.S. wood screws.

Providing and fixing IS:12817 marked stainless steel butt hinges of size 125 x 64 x 2.5 mm (heavy weight)" of approved make with suitable stainless steel screws etc. Complete as directed by Engineer-in-charge.

Providing and fixing stainless steel tower bolts of following sizes, make as per specifications.

Providing and fixing stainless steel tower bolts of size 300 X 12 mm of approved make with necessary screws etc. all as per specifications and as per drawings.

Providing and fixing stainless steel tower bolts of size 200 X 12 mm with necessary screws etc.all as per specifications and as per drawings.

Providing and fixing approved make 7 Lever Night latch including necessary screws etc in wooden doors complete all as directed at site .

Providing and fixing brass mortise latch and lock of approved make with 6 levers and a pair of lever Brass handles with necessary screws etc complete suitable for fixing in wooden / steel/ FRP/ doors as per specifications.

Providing and fixing "Godrej" make mortice Key less latch with chrome or Powder Coated finish and a pair of lever handles with necessary screws etc complete in all kind of airlock, bath / toilet Doors / false ceiling trap doors.

Providing and fixing door closers

Providing and fixing IS: 3564 marked aluminium die cast body tubular type universal hydraulic door closer of approved make with necessary accessories and screws etc. in wooden doors / steel doors with necessary bolts & nuts complete as per specifications and as directed by the Engineer-in-charge.

Providing supply and fixing Door Closer TS 71- DORMA- Std Arm.with necessary accessories and screws etc…. As per manufactures instruction, specifications and as directed by EIC.

Providing and fixing double action hydraulic floor spring

Providing and fixing double action hydraulic floor spring of approved brand and manufacturer (conforming to relevant Indian Standard) for doors including cost of cutting floors as required, embedding in floors and cover plates with M.S pivot and single piece of M.S sheet outer box with slide plate etc. complete as per directions of Engineer-in-charge with brass cover plate.

Providing and replacing existing double action hydraulic floor spring 'DORMA' make of specified Model No. BTS75 / 84/80 / 65 with top Pivots etc. or approved equivalent brand and manufacturer for wooden doors. including cost of cutting floors as required, embedding in floors and cover plates with Dorma make pivot and outer box with slide plate etc. complete as per directions of Engineer-in-Charge with stainless steel cover plate as approved by the Engineer -in-Charge.

Providing and fixing pair of S S Door handles- 22mm dia 250 mm long- KICH- 316 grade in Steel Doors/ wooden Doors including screws / bolts etc. all as per drawings and specifications complete.Sample shall be get approved by the Engineer-in-charge. ( Pair means 2 Nos, 1 set)

Providing and fixing pair of offset type S S Door handles- 22 mm dia 250 mm long suitable for aluminium doors including screws / bolts etc. all as per drawings and specifications complete.Sample shall be get approved by the Engineer-in-charge. ( Pair means 2 Nos, 1 set). sample shall got approved by EIC, before purchase of this item.

LOUVERED OPENING Providing & fixing LOUVERED OPENING of required size in door shutters including making the opening, providing & fixing teak wood louver blades with necessary teak wood frame work, beading & applying one coat of approved wood primer etc. complete.

Providing, Fixing /Replacing the damaged mesh of existing/ new doors louvers up to 0.3 Sqm with new aluminium mesh of 1.6mm thick of approved pattern & design in all type of doors including 25x12 mm second class teak wood beading, screws, nails etc... complete and disposal of old scrap at designated point for further disposal as directed by EIC.

Providing and fixing anodised Aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections / Z sections and other sections of approved make conforming to IS 733 and IS 1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fastners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC / neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically whereever required including cleat angle, aluminium snap beading for glazing / panelling, C.P brass / stainless screws all complete as per drawings and and directions of Engineer-in-charge including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of PVC / neoprene gasket required filling the gaps using silicon grout sealent etc. (fittings glazing and panelling shall be paid for separately)

Anodised Aluminium sections (Minimum anodizing thickness of 15 micron)

Extra for colour anodizing

Providing and fixing 12 mm thick pre-laminated particle board flat pressed 3 layer or graded wood particle board conforming to IS 12823 Grade-I, Type - II in panelling fixed in aluminium doors, windows, shutters and partition frames with C.P Brass / Stainless steel screws etc. complete as per architectural drawings and directions of Engineer-in-charge Prelaminated particle board with decorative lamination on both sides.

Providing and fixing glazing With clear float glass panes of 5.00 mm thickness in aluminium / wooden doors, window, ventilator shutters and partitions etc with PVC / Neoprene gasket etc. complete as per the architectural drawings and directions of the Engineer-in-charge (Cost of snap beading shall be paid in basic item)

Providing, supplying and fixing hollow metal flush steel doors double leaf / single leaf 40 mm thick of approved make consisting of door frame and shutters and all hardware fittings, grooved frame with EDPM beeding in grooves for air tightness and made out of 14g thick G.I sheets and shutters made of 16g thick sheets, hollow portion of shutters filled with puff, including necessary stiffners in shutters and frame, vision panel of specified size with 4 mm glass and clip on pressed steel frame for vision panels, fixing 4 nos heavy duty stainless steel 304 grade ball bearing hinges, mortise / dead lock of approved make, a pair of 200 mm long stainless steel handles, 250 mm long stailless steel tower bolt / concealed tower bolt , etc... frame hollow portion filled with PCC 1:2:4, necessary hold fast embedded in concrete, fixing in concrete with anchor fastners. finished with Polyurethane painting / powder coating of approved colour complete all as per drawings and specifications and as directed by the Engineer-in-charge

Providing and fixing of 4 mm thick approved make and shade Aluminium Composite Metal Panel in panelling fixed in aluminium doors, windows, shutters and partition frames with PVC/ Neoprene gasket, Clips, beeding, C.P Brass / Stainless steel screws etc. complete as per specifications and directions of Engineer-in-charge. The ACM Panel composition shall be of 0.5 mm thick PVDF coated aluminium sheet + 3 mm thick low density polyethelene virgin resin core + 0.5 mm thick polyester (PVDF) coated Aluminium sheet.

Providing and fixing approved quality stain less steel body roller wheels of approved make for sliding shutters.

Providing and fixing 4 Lever Mortice Lock of approved make suitable for aluminium sections.

Providng and fixing Aluminium Grill 10 mm thick "DECO GRILLE" make Model No. DG- 202 in Champagne, black, Bronze, Gold colour anodising of min 15 Microns by the manufacturer with a opening size of 60mm x 45mm and Minimum weight of 4.12 Kg/ Sq.M including providing anfd fixing Suitable 'F' / 'H' section outer frame and mullion fixing with screws complete all as per specifications and as directed at site by the Engineer-in-charge. Aluminium alloy shall be of 6063-T6 with yield strength of minimum 6.5 kg/ sq.mm.

Providing and fixing C.P brass towel rail of approved make 600 mm long complete fixed to walls with 30 mm CP brass screws with concealed fitting arrangement all as directed by the Engineer-in- charge.

Providing and fixing 6 mm thick mirrors of size 600 x 450 mm of approved make with bevelled edges complete with 6 mm thick asbestos sheet back ground fixed to walls with C.P. brass screws and concealed washers complete. all as per specifications and as directed by the Engineer-in-charge .

Extra for providing and fixing mirrors with approved make- stainless steel 304 grade STUDS (with wall spacers) complete all as per specifications and as directed by the Enginner-in-charge

Only installation charges for replacing/refixing of the existing damaged false ceiling panel with new ones.

Refixing of existing aluminium false ceiling panel Only Labour charges for refixing of the existing aluminium false ceiling panel: 1. Following sizes of panel 253 mm x 1270 mm or 600 mm x 600 mm or 84C panel. 2. Providing necessary scaffolding/working ladder. 3. Panels are to be fixed/refixed to false ceiling in existing frame works.

Extra over item no: 31.1 for supply of "LUXALON" False Ceiling 84C / panels of size 253 mm x 1270 mm / 600 mm x 600 mm Un-perforated corrosion resistant Aluminium Magnesium alloy metal Panels of approved colour consisting of Panel 84 mm wide x12.50 mm deep x 0.50 mm thick with square edges and recess flange of 24 mm, panel length up to 6.00 metres, coil coated on a continuous paint line. Double baked and roll formed from double baked enamelled corrosion resistant Aluminium Magnesium alloy AA 5050 for higher strength and good roll forming characteristics.

Providing, Replacing the existing damaged asbestos cement sheet in false ceiling with new 6mm thick flat fibre cement sheets conforming to IS: 14862 of approved make including fixing the sheets to existing frame work with suitable screws/ nut bolt & forming necessary grooves as required, including cutting the sheets to required size, making opening around electrical fixtures, AC grills and Trap doors; fixing to line and level, cleaning and removing accumulated waste materials like glass wool if any above false ceiling, including cleaning of site, scaffolding etc.. complete and disposal of debris at collection point at specified location in Filter House building, around 300 mtrs etc... complete as per specifications, and as directed by EIC at site..( Fixed sheet in position will be measured for payment, no wastage will be considered.)

Silicon sealent. Filling the gap between aluminium frame & adjacent RCC / Brick work / Stone work Joints by providing weather silicon sealant ( M/s Dow Corning or approved equilent for the specified purpose ) over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete Up to 5 mm depth and 5 mm width.

Supplying and fixing Rolling shutters gear operated type with handles including top hood 0.90 mm thick of approved make as per ISI standards made out of required size of MS lathes 18 gauge interlocked together throughout entire length and jointed together at the end by end locks mounted on specially designed pipes shaft with brackets, side guides and arrangements for inside & outside locking with push and pull operation complete including the cost of providing and fixing necessary springs of required size for rolling shutters.

Extra over item no: 34, for the cost of rolling shutters for providing wicket gate of specified size in the M.S rolling shutters including fixing with fixing arrangements, hinges, locking arrangements, frames etc. all as per standard specifications and as directed by the Engineer-in- charge complete.

Servicing of the following type of rolling shutters of all sizes up to maximum size of 6m x 7m including scaffolding, by dismantling for over-hauling of individual parts for repairing and refixing after repaires i.e top hood shaft cage, shaft case, shaft brackets, springs, main curtain with lathe or mid bar type grills, wicket gate, side guides bottom rails, gear units, bearings, electric motors,starters and thoroughly cleaning all the components, adjusting the tensioning springs, if required overhauling or repairing shaft and gear units, re-conditioning end clips, re-aligning curtain ends, reconditioning dents if any, on the surface bottom rail and side guides, repairing the starter, inspecting, taking out and replacing the damaged or defective components (replacement of parts at extra rate is given under relevant item), ensuring proper locking arrangements from both side and out side including all welding, drilling, straightening , grinding, scaffolding, ladders, tools, tackles, with all consumables, such as lubricants, kerosene, grease etc. and shall hardware such as nuts, bolts, rivets, screws, washers, keys, etc. making good any damages to civil works,cleaning, oiling, greasing and demonstrating proper functioning of the shutters after each service such as nuts, bolts, rivets, screws, washers, keys, etc. and necessary scaffolding etc. all complete as per direction of Engineer-in-charge at site. a) Electrically operated type with lathes or grilled curtain, Mechanical Gear operated and Pull & Push type rolling shutters ( All types of Rolling Shutters)Note:1) Measurement will be done once only, for entire period of contract. 2) The measurement of Rolling shutters will be as per structural openings. 3) Rate includes fixing of rubber gasket min 6mm thick at bottom of rolling shutter on external shutters for prevent entry of reptiles.

Providing, Supplying and replacing in position wherever required the following parts after removing the damaged old part carefully including all labour, taxes, duties, scaffolding, transport, welding, drilling, grinding, tools, tackles etc. and with applying one coat of primer wherever required, including transporting the dismantled M.S/ metal scrap and depositing at Trombay stores as directed by the Engineer-in-charge at site. Up to 5.00 M Height.

G.I .lathe sections 75mm wide & 18g thick.

M. S. bottom rails (pressed type 10G with locking arrangement, handles, etc. in both ends and sides.

Providing, supplying , fabricating and fixing M.S. hood cover with 0.90 mm thick M.S sheet with supports for rolling shutters complete including erection.

Providing, supplying and fixing M.S. guide channals with supports for existing rolling shutters complete including erection.

Providing, supplying and fixing gear wheel to existing rolling shutters complete including erection. (a) 250 mm Dia

Providing, supplying and fixing Springs in Rolling shutter Shaft including necessary bolt& nuts complete including erection. For rolling shutter up to 5.00 metres height

Providing, supplying and fixing Gear Box set with gear wheels & handle full assembly, Labour for fixing including erection for rolling shutters by dismantling old gear box if any at site.

Providing, supplying and fixing Side Brackets for Rolling Shutters Complete including erection.

Removing the following sizes of damaged G.I fittings / Pipes from G.I pipe lines, replacing the damaged fittings with new fittings, testing for leakage etc. complete as per specifications and as directed by the Engineer-in-charge.

15 mm G.I elbow, bend, nipple, socket, tee etc.

25 mm G.I elbow, bend, nipple, socket, tee etc.

50 mm G.I elbow, bend, nipple, socket tee, socket etc.

Providing , Laying , jointing, fixing and testing Heavy quality (C- Class) Galvanised Iron pipes and ISI marked fittings like, tees, elbows, bends, unions, nipples,reducers etc. as required for the work, including testing the pipes and fittings for 10.00 Kg / Sq.Cm hydralic pressure with a minimum period of two hours duration with clean water, including cutting , threading, jointing with hemp yarn, white lead, jointing Teflon tape, exposed / concealed by chasing walls and making good by filling with concrete 1:3:6, complete all as per specifications and drawings, including two coats of anti corrosive bitumastic paint for all concealed lines / two coats of synthetic enamel paint for all exposed lines all as directed by the Engineer-in-charge. Pipes with exclusive use of TATA make C-Class pipes.

15 mm dia G.I pipe

25 mm dia G.I pipe

50 mm dia G.I pipe

Providing and fixing Chlorinated (CPVC) pipes having thermal stability for hot & cold water supply (as ASTM Standard 2846 & SDR - 11 Grade) including all CPVC Plain & Brass threaded fittings, fixing the pipe with clamps at 1.00 m spacing.This includes jointing of pipes & fittings with CPVC Solvent cement & testing the joints complete all as per specifications, drawings and as directed by the Project Engineer.

CPVC Pipes 40 mm OD SDR 11

CPVC Pipes 25 mm OD SDR 11

CPVC Pipes 15 mm OD SDR 11

Providing & fixing / replacing (damaged) in position heavy pattern screw down gun metal gate valve with handles and wheels of approved make including testing for 10Kg/cm2 pressure with clean and potable water with a minimum testing duration of two hours etc.as per specification and as directed by the Engineer-in-charge.

Providing and fixing 15 mm dia C.P brass bib cock of approved type and make of heavy quality of specified / approved make as per specifications and as directed by the Engineer-in-charge

Providing and fixing 15 mm n.b CP Brass open stop cock of approved make and type / Heavy Quality of specified as per specifications and as directed by the Engineer-in-charge.

Providing and fixing 15 mm C.P brass Angle cock of heavy quality of specified / approved make, for wash basin inlet / flush cistern etc. as per specifications and as directed by the Engineer-in-charge

Providing and fixing CP brass / copper inlet connection pipes heavy quality suitable for hot and cold including CP brass unions and nuts 15 mm dia 600 mm long.

Providing and Fixing CP brass 100 mm dia shower rose with Shower arm of Specified make as per specifications and as directed by Engineer-in-charge complete.

Providing and fixing Heavy Quality 15 mm C.P brass pillar cock of approved make quarter turn and type as per specifications and as directed by the Engineer-in-charge.

Providing and fixing heavy quality health faucet with 1.50 metres long flexible hose (hand shower) of approved make with wall brackets and type as per specifications and as directed by the Engineer-in-charge

Providing and fixing heavy quality stainless steel / C.P brass grating 125mm dia of approved equvalent make as specified for floor traps / nahani traps all as directed by the Engineer-in-charge

Providing and fixing Brass 15 mm C.P presstomatic series auto shut urinal flush cock of approved make and quality

Providing and fixing viterious China wash basin of approved make, size 550 x 400 mm / 550 x 420 mm and equivalent sizes and colour with C.I. brackets, 15 m C.P. brass pillar tap of approved make,15 mm x 600mm long PVC Inlet connection, 32 mm heavy quality C.P. brass waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls and testing complete all as per specifications and as directed by the Engineer-in-charge.

Providing & fixing 15mm C.P Brass Bib Cock with Extended Lever Handle and Wall flange of jaquar make model no: FLR-5043N / Approved equivalent make as per specifications and as directed by EIC at site.

Providing & fixing 15mm C.P Brass Pillar / Bib tapTap Elbow Operated / Lever operated ESSCO / Approved equivalent make as per specifications and as directed by EIC at site.

Providing and fixing / Replacing PVC low level / high level flushing cistern 10 litre capacity of approved make in white colour with flush pipe with manually controlled device (handle lever) conforming to IS:7231, with all fittings and fixtures etc. complete as per specifications and as directed by the Engineer-in-charge.

Providing and fixing Glazed VITRIFIED floor tiles / wall tiles of approved make in different sizes like 600x600 / 300x600 etc.. conforming to IS 15622 in all colours and shades in Glossy or Matt or satin finish laid over a bed of minimum 20 mm thick bed of cement mortar 1:4 (using Crushed sand) and jointing with grey cement slurry including grouting with the joints with white cement based Tile Grout of approved make and matching shade complete as per patterns, drawings and specifications complete as directed by the Engineer-in-charge.

Labour charges only for rectify the pipe leakage by fixing temporary clamps including preperation of clamps and gaskets for water lines in false ceilings / walls / service ducts, under ground services etc.. & joining the line by welding / threading etc... as per site requirement there after in G.I pipelines up to 100mm dia in RLG building.

Providing and fixing brass ball cock (TECHNO make) or approved Equivalent heavy quality of following sizes with arm rod and Plastic Ball floats complete as per specifications and as directed by the Engineer-In-Charge.

25 mm Brass Ball Cock with PVC Ball Techno Make

50 mm Brass Ball Cock with PVC Ball Techno Make

Providing and fixing C.P Brass 2 in 1 Bib cock and Angle cock combination of Heavy Quality of specified / approved make as per specifications and as directed by the Project Engineer (Samples to be got approved by the Project Engineer) of 15 mm n.b .

Providing and fixing Heavy Quality CP Brass Bottle trap 31 / 32 mm (Jaquar or Plato or approved equivalent make) single piece moulded with height of 270mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal,of "Jaquar "or approved equivalent approvedmake for wash basins / urinal etc all as per specifications and directed by the Engineer in Charge.

Providing and fixing Black/White solid plastic seat with lid (Hindware/ Parryware make or approved make suitable to existing EWC) including CP Brass / SS bolts, screws etc. for pedestal type E.W.C./A.I.W.C. pan complete as per specifications and as directed by the Engineer-in-Charge

Providing and replacing Heavy Quality C.P .Brass waste coupling of following dia for wash basin, sink and/or Urinal (dome type) of approved make, size, shape and quality all as directed complete with C.P Brass Waste coupling 32 mm Dia and minimum 79 mm length Half threaded or Full threaded as per requirement.

C.P. brass Urinal spreader Providing and fixing 15 mm C.P Brass Urinal spreader size with 1/2" BSP thread and shapes, weighing not less than 60 gms of "PLATO" or approved make and type.

Providing and fixing stainless steel AISI 304 (18/8) satin finish kitchen sink with drain board with over all size of 1145 x 510 mm and bowl size of 560 x 410 mm and 241 mm depth of approved make and model with C.I. brackets and stainless steel waste coupling, fittings, including painting the fittings and brackets with 3 coats of white enamel paint over a coat of primer, cutting and making good the walls wherever requried.complete as per specifications and as directed by the Engineer-in-charge

Soap Dispenser Providing & fixing approved type heavy duty Euronics Liquid soap Dispenser S.STEEL SOAP DISPENSER (SATIN FINISH)-1000ML or equivalent with S.S brackets, cap etc. fixed to wall with C.P. brass screws, & screwed on to wooden rawl plugs etc. complete.

Providing and painting two (or) more coats with Epoxy paint at all locations prepared and applied as per manufacturer' specifications including a priming coat if specified by the manufacturer, preparation of surface by cleaning with wire brush and rubbing with sand paper to remove dust, dirt etc, after first coat Epoxy based trowelling compound if required, including preparation of the surface by scrapping, applying sand paper,by cleaning with wire brush and rubbing, making free of rust, dirt etc. filling the holes, joints, cracks if any etc. complete.all as per manufacturers technical data and as directed at site to acheive 200 micron film thickness (50 micron primer coat + 150 micron finishing coat).

Providing and painting TWO coats of synthetic enamel paint on new wooden surfaces of approved brand and manufacturer of required colour to give an even shade over an under coat of suitable shade primer of approved brand and manufacturer including preparation of the surfaces, scaffolding complete. as per specifications and as directed by the Engineer-in-charge

Providing SFMC Micro concrete using 100% SFMC for strengthening of structural members including mixing, pouring, curing as per manufacturer specifications and as directed by the Engineer-in-charge.

Providing and constructing brick work in super structure with standard bricks in C.M 1:4 using crushed Sand cement mortar using Standard bricks of approved quality / class, make / brand in super structure above plinth up to Floor-II level in all shapes and sizes including curing, raking out joints complete as per specifications and as directed by the Engineer-in-charge. Note: Thickness of brick masonry shall be 230 mm / 110 mm. This item shall be operated as and when ever required at site.

Providing 20 mm thick plastering using Ready mix external plastering compound of approved make for external faces of brickwork / concrete surfaces including preparation of the surface, curing, cleaning scaffolding up to 10 metres height complete.all as per specifications including forming drip moulds wherever necessary and as directed by the Engineer-in-charge. Note : This item shall be operated as and when ever required at site.

Providing and laying in position cement concrete of 1:2:4 (1 cement, 2 crushed sand, 4 graded stone aggregate of nominal size 20 mm) including consolidation, finishing, curing etc. complete as per specification and drawings but excluding the cost of Formwork shuttering, centering and steel reinforcement at all Levels. Note: This item shall be operated as and when ever required at site.

Automatic Hand Dryer ULTRA THIN HIGH SPEED STAINLESS STEEL HAND DRYER (HEAVY DUTY) Providing and fixing automatic hand dryer a size/dimension 27.5-30 cm having electronic infrared detection sensor, Material- stainless steel 304,model no: EH24S of M/s Euronics. with hand dry time 7-12 seconds, Auto Cutoff 60 seconds, Noise Level 72 db(A), Motor- Brush AC Type, Speed 22,000 RPM Voltage- 220 V / 50 Hz, Rated Power- 400W-950W, Switch - Hot & Cold Option etc... complete as per specifications ans as directed/approved by the EIC.

Supply of suitable skilled and unskilled manpower with set of hand tools / drilling / cutting machines for miscellaneous jobs like carpentry maintenance, plumbing and masonry jobs. NOTE: Suitable manpower shall be deployed for the job assigned with safety gears as & whenever required. Man power shall be deployed as per requirement, including holidays & late working if required.

Supply of highly skilled Carpenter / plumber / mason.

Unskilled labours.

Providing Structural steel work Up to and including 300 mm Joists, 350 mm channels, and below sections using materials produced by SAIL / RINL (Vizag Steel) / TATA. All test ..........a priming coat of approved steel primer etc. complete all as per specifications, drawings and as directed by the Engineer in charge

Providing and fixing Minimum 17 mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut Granite of Telephone Black colour for kitchen platforms, vanitiy counters, Wash basin Counters, Door Frames, window sills, facias and similar locations of required size, colour and texture laid over 20 mm thick base cement mortar 1:4 (using crushed sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing the edges to give high gloss finish etc. complete as directed by the Engineer-in-charge at all levels