Loading
Loading…
Loading…
Tender Value
₹94.9 L
EMD Value
₹1.9 L
Closing Date
24 Apr 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
45 days
Expenditure
Capital (Works)
Above/Below/Par
TECHNICAL
15 conditions · 4 needing a document upload
The tenderer must have minimum average annual contractual turnover of [V/N or 'V' whichever is less; where V = Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Tenderer must have to submit valid Electrical Contractor license as per Indian Electricity Rules for the respective category of works issued by Government Electrical License Board on or before the closing date of tender. Copy of the electrical contractor license should be submitted along with the tender offer, otherwise, the tender will be summarily rejected.
Experience in similar nature of work:- a) The tenderer must have successfully completed any of the following during last 07(seven) years, ending last day of month previous to the one in which tender is invited: Three similar nature of works each costing not less than the amount equal to 30% of the advertised value of the tender, or Two similar nature of works each costing not less than the amount equal to 40% of the advertised value of the tender, or One similar nature of work each costing not less than the amount equal to 60% of the advertised value of the tender. (b) (i) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. And in the case of major bridges - substructure, superstructure etc.), the tenderer must have successfully completed any of the following during last 07 (seven) years, ending the last day of the month previous to the one in which tender is invited: Three similar nature of works each costing not less than the an amount equal to 30% of the advertised value of each component of the tender, or Two similar nature of works each costing not less than the amount equal to 40% of the advertised value of each component of tender, or One similar nature of work each costing not less than the amount equal to 60 % of the advertised value of each component of the tender. Note for b(i): Separate completed works of minimum required values for each component shall also be considered for fulfillment of technical eligibility criteria. (b) (ii) In such cases, what constitutes a component in a composite work shall be clearly predefined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (iii) To evaluate the technical eligibility of the tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility shall be considered. The scope of work covered in other remaining components shall be either executed by the tenderer himself if he has work experience as mentioned in clause 7 (a) (ii) of Part-II of GCC or through subcontractor fulfilling the requirements as per clause 7 of Part-II of GCC or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarised, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfillment of technical eligibility. In case after the award of the contract or during the execution of work it becomes necessary for the contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of Part-II of GCC, with prior approval of the Chief Engineer in writing.
The Similar nature of works for this instant tender shall be "Supply, installation, testing and commissioning of any LT/HT electrical work." The tenderer should have executed the similar nature of works in Central/State Government department or PSUs of Central /State Government."
50 conditions · 4 needing a document upload
Whether the cost of earnest money deposited
Migration to GST regime - Special Tender Conditions: The rates should clearly indicate the rate of applicable duties and taxes included in the prices quoted by them. Any variation in tax structure/ rate due to introduction of GST, shall be dealt with under Statutory Variation Clause. It should be ensure that bidders/tenderers are GST compliant and quoted tax structure/rates are as per GST Law.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Contractor should submit the GSTIN number and same should be mentioned in the bills along with a copy of GSTIN registration certificate while submitting the bills to accounts for audit and payment, As GST is scheduled to implemented wef 01.07.2017. Without GSTN, no bill will be accepted w.e.f. 01.07.2017
From 01.07.2017 GST has been implemented but the detail guideline is still not clear. Hence, new tax structure on materials and labour will be applicable to both Railway & contractor after getting proper notification
Payment of Earnest Money deposit (EMD) , in respect of e- tendering,should be accepted through net banking or online payment gateway only
1. Improvement of staff amenities by providing new house connection pipe lines by replacing existing damaged pipe lines and sanitary fittings of single storied, double storied building etc under the jurisdiction of SSE/W/WS/LMG(Electric portion). 2. At Migrendisa (MGE) construction of 8 units standard type-II quarters in replacement of abandoned quarters under the jurisdiction of Sr.DEN/III/LMG (Electric portion) 3. At New Harangajao (NHGJ) construction of 10 units standard type-II quarters in replacement of abandoned quarters under the jurisdiction of Sr. DEN/III/LMG(Electric portion).4. At AGTL-Provision of new quarter Type-II(18 units) under jurisdiction of DEN/V/LMG(Electric portion). 5. Upgradation/special repair staff quarters (type II, type III, type IV) in different colonies under the jurisdiction of SSE/W/East/PNO and SSE/W/West/PNO. (Electric portion).
EL-LM-26-27-01
EL-LM-26-27-01
Open
Works - General
120 Days
Hojai, Assam
₹0
₹1.9 L
24 Apr 2026
2 Apr 2026
10 Apr 2026
215 items across 5 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 26,48,456.17 | ||
| — | 10.00 | — | — | ||
| Supply, installation, testing and commissioning (SITC) of ISI marked 3-phase submersible pump set suitable for bore-well application, complete in all respects, with the following specifications and scope. The pump set shall be 7.5 HP / 5.5 kW capacity, suitable for operation on 3-phase, 415 V ±10%, 50 Hz AC supply, having maximum current rating of 14.5 Amps, discharge capacity of 3.33 LPS at rated head of 100 metres, with 12 stages and rated speed of 2880 RPM. The pump shall be 5-Star rated energy efficient model. The pump shall be suitable for installation in bore wells having minimum inner diameter of 150 mm, with pump outlet size of 50 mm, and designed for handling clear, cold water. The submersible pump shall conform to IS:8034 (latest) and shall be ISI marked, and the submersible motor shall conform to IS:9283 (latest) of wet type construction, suitable for continuous duty (Duty Type S1), synchronous speed, Category-B insulation class.The pump shall be installed strictly as per manufacturer's recommendations and direction of Engineer-in- Charge at site.Necessary trial run and performance testing shall be conducted after installation to ensure proper functioning and achievement of rated discharge and head. Any item, component or accessory not specifically mentioned in the schedule but essential for safe, reliable and efficient working of the pump set shall be deemed to be included in the scope of the contractor, and no extra payment shall be admissible on this account. The quoted rate shall therefore be inclusive of all materials, labour, tools & plants, testing, commissioning and incidental charges required for complete execution of the work. | — | — | — | 4,98,091.7 | |
| — | 10.00 | — | — | ||
| Supply, installation, testing and commissioning (SITC) of Fully Automatic Star-Delta Starter suitable for 7.5 HP pump-motor, complete in all respects. The starter shall be suitable for operation on 3-Phase, 415 Volts ±10%, 50 Hz AC supply and shall be designed for reliable starting, protection and control of submersible pump motor. The starter shall be of fully automatic Star-Delta type incorporating necessary control and protection featuresi.e. Thermal overload relay, Short circuit protection through MCCB / HRC fuse, Single phasing / phase failure protection, Under-voltage / over- voltage protection, Dry-run protection (wherever applicable for pump operation), Timer for Star- Delta changeover. The starter shall be provided with Ammeter and Voltmeter with selector switch for phase selection and shall include a 3-position Auto-Manual-Off selector switch for operational flexibility. The starter panel enclosure shall be made of stainless steel (SS) housing, weatherproof, dust and vermin proof, suitable for outdoor installation (minimum protection IP-54).The panel shall be mounted on suitable MS frame / wall mounting arrangement as required at site.The work shall include fixing of starter panel, power and control cable termination, earthing, functional testing and trial operation of pump motor through starter. The starter shall be commissioned as directed by the Engineer-in-Charge at site. | — | — | — | 1,22,185.3 | |
| — | 10.00 | — | — | ||
| Supply, installation, testing and commissioning (SITC) of ISI marked 3-Phase submersible pump set suitable for bore-well application for pumping of clear and cold water, complete in all respects. The pump set shall be of 5 HP (3.7 kW) capacity suitable for operation on 3- Phase, 415 Volts ±10%, 50 Hz AC supply, having maximum full load current not exceeding 10 Amps, discharge capacity of 2 litres per second at rated head of 90 metres, with minimum 8 stages and rated speed approximately 2900 RPM. The pump shall have outlet size of 50 mm and shall be suitable for installation in bore wells having minimum inner diameter of 150 mm. The pump set shall be designed for handling clear, cold water and shall be of multistage centrifugal type suitable for continuous operation. The submersible pump shall conform to IS:8034 (latest revision) and shall be ISI marked, and the submersible motor shall conform to IS:9283 (latest revision) of wet type, rewindable construction, suitable for continuous duty (Duty Type S1) with Category-B insulation or better. The scope shall include complete supply, transportation, lowering, installation, alignment, testing and commissioning of the pump set along with all necessary accessories.Installation shall be carried out strictly as per manufacturer's recommendations and as directed by the Engineer-in- Charge at site. Necessary trial run and performance testing shall be conducted after installation to ensure proper functioning and achievement of rated discharge and head.Any item, component or accessory not specifically mentioned in the schedule but essential for safe, reliable and efficient working of the pump set shall be deemed to be included in the scope of the contractor, and no extra payment shall be admissible on this account. The quoted rate shall therefore be inclusive of all materials, labour, tools & plants, testing, commissioning and incidental charges required for complete execution of the work. | — | — | — | 3,77,134.2 | |
| — | 10.00 | — | — | ||
| Supply, installation, testing and commissioning (SITC) of Fully Automatic Star-Delta Starter suitable for 5 HP pump-motor, complete in all respects. The starter shall be suitable for operation on 3-Phase, 415 Volts ±10%, 50 Hz AC supply and shall be designed for reliable starting, protection and control of submersible pump motor. The starter shall be of fully automatic Star-Delta type incorporating necessary control and protection featuresi.e. Thermal overload relay, Short circuit protection through MCCB / HRC fuse, Single phasing / phase failure protection, Under-voltage / over- voltage protection, Dry-run protection (wherever applicable for pump operation), Timer for Star- Delta changeover. The starter shall be provided with Ammeter and Voltmeter with selector switch for phase selection and shall include a 3-position Auto-Manual-Off selector switch for operational flexibility. The starter panel enclosure shall be made of stainless steel (SS) housing, weatherproof, dust and vermin proof, suitable for outdoor installation (minimum protection IP-54).The panel shall be mounted on suitable MS frame / wall mounting arrangement as required at site.The work shall include fixing of starter panel, power and control cable termination, earthing, functional testing and trial operation of pump motor through starter. The starter shall be commissioned as directed by the Engineer-in-Charge at site. | — | — | — | 98,300 | |
| — | 10.00 | — | — | ||
| Supply, installation, testing and commissioning (SITC) of 3 HP (2.2 kW) Submersible Monoblock Pump Motor Set suitable for pumping clear water, capable of delivering 150-70 LPM discharge at total head of 15 metres, suitable for installation in minimum 100 mm bore size, complete in all respects. The scope shall include supply of pump set along with necessary submersible cable, delivery pipe with fittings, NRV/valve, starter/control arrangement, earthing, lowering/placement, installation, testing and trial run as per manufacturer's recommendations and as directed by the Engineer-in-Charge at site. Necessary trial run and performance testing shall be conducted after installation to ensure proper functioning and achievement of rated discharge and head.Any item, component or accessory not specifically mentioned in the schedule but essential for safe, reliable and efficient working of the pump set shall be deemed to be included in the scope of the contractor, and no extra payment shall be admissible on this account. The quoted rate shall therefore be inclusive of all materials, labour, tools & plants, testing, commissioning and incidental charges required for complete execution of the work. | — | — | — | 3,37,372 | |
| — | 4.00 | — | — | ||
| Supply, installation, testing and commissioning (SITC) of ISI marked 3 HP (2.2 kW) single phase submersible pump set suitable for installation in 100 mm dia bore well, complete in all respects. The pump shall have delivery size 32 mm, minimum 25 stages, rated speed approximately 2780 RPM, and shall be capable of delivering water against a total head of 100 metres. The pump motor shall be wet type suitable for continuous duty, conforming to IS:9283 (latest) and shall be BEE 5-Star rated energy efficient model. The scope shall include supply of pump set along with necessary submersible cable, delivery pipe with fittings, NRV/valves, starter/control arrangement, earthing, lowering, installation, testing and trial run, to ensure satisfactory performance, strictly as per manufacturer's recommendations and as directed by the Engineer-in-Charge at site.Necessary trial run and performance testing shall be conducted after installation to ensure proper functioning and achievement of rated discharge and head. Any item, component or accessory not specifically mentioned in the schedule but essential for safe, reliable and efficient working of the pump set shall be deemed to be included in the scope of the contractor, and no extra payment shall be admissible on this account. The quoted rate shall therefore be inclusive of all materials, labour, tools & plants, testing, commissioning and incidental charges required for complete execution of the work. | — | — | — | 97,696 | |
| — | 14.00 | — | — | ||
| Supply, fixing, connection, testing and commissioning of single phase starter suitable for 3 HP submersible pump motor, complete in all respects. The starter shall be suitable for operation on 230 Volts, Single Phase, 50 Hz AC supply and shall be provided with necessary starting arrangement, overload protection, short circuit protection, single phasing / voltage protection, indicating lamps, proper internal wiring, cable glands, lugs and earthing. The scope shall include mounting of starter, power cable connection, termination, functional testing and trial operation of pump motor as per direction of Engineer-in-Charge at site. | — | — | — | 1,09,620 | |
| — | 3.00 | — | — | ||
| Supply, installation, testing and commissioning (SITC) of ISI marked 3 HP (2.2 kW), three phase submersible pump set suitable for installation in 100 mm bore well, complete in all respects. The pump shall be of multistage type having delivery size 50 mm, with cast iron grade suction and discharge casing, and glass nylon / polypropylene impellers, capable of delivering 9612 litres per hour against a total head of 45 metres, at a rated speed approximately 2854 RPM. The motor shall be wet type suitable for continuous duty, conforming to IS:9283 (latest revision) and suitable for operation on 3-Phase, 415 Volts, 50 Hz AC supply. The scope shall include supply of pump set along with necessary submersible cable, delivery pipe with fittings, NRV/valves, starter/control arrangement, earthing, lowering, installation, testing and trial run, as per manufacturer's recommendations and as directed by the Engineer-in-Charge at site.Necessary trial run and performance testing shall be conducted after installation to ensure proper functioning and achievement of rated discharge and head. Any item, component or accessory not specifically mentioned in the schedule but essential for safe, reliable and efficient working of the pump set shall be deemed to be included in the scope of the contractor, and no extra payment shall be admissible on this account. The quoted rate shall therefore be inclusive of all materials, labour, tools & plants, testing, commissioning and incidental charges required for complete execution of the work. | — | — | — | 1,06,496.97 | |
| — | 3.00 | — | — | ||
| Supply, fixing, connection, testing and commissioning of starter suitable for three phase 3 HP submersible pump motor, complete in all respects. The starter shall be suitable for operation on 3-Phase, 415 Volts, 50 Hz AC supply and shall be provided with necessary starting arrangement, overload protection, short circuit protection, single phasing / phase failure protection, under-voltage protection, indicating lamps, proper internal wiring, cable glands, lugs and earthing. The scope shall include mounting / fixing of starter panel, power cable connection, termination, functional testing and trial operation of the pump motor as per direction of the Engineer-in-Charge at site. | — | — | — | 51,270 | |
| — | 400.00 | — | — | ||
| Supply of 2 inch dia CPVC pipe suitable for use as delivery / column pipe for submersible pump application, conforming to relevant IS standards, complete with necessary sockets / couplers, capable of withstanding required working pressure. The pipe shall be corrosion resistant, smooth internal finish, suitable for potable / clear water use, and shall be supplied in standard lengths as approved by the Engineer-in-Charge. | — | — | — | 64,736 | |
| — | 400.00 | — | — | ||
| Supply of 1.5 inch dia CPVC pipe suitable for use as delivery / column pipe for submersible pump installation, conforming to relevant IS standards, complete with required sockets / couplers, suitable for specified working pressure conditions. The pipe shall be corrosion resistant, suitable for handling clear / potable water, having smooth internal surface and adequate mechanical strength. Pipes shall be supplied in standard commercial lengths as approved by the Engineer-in- Charge. | — | — | — | 23,304 | |
| — | 1000.00 | — | — | ||
| Supply, erection and commissioning of 12 mm dia steel wire rope with PVC insulation coating suitable for suspension / protection of submersible pump against accidental falling inside bore well, complete in all respects. The rope shall be of adequate tensile strength, corrosion resistant and suitable for submersible pump lowering application, and shall be provided with necessary clamps, thimbles, fastening arrangement and proper fixing at top support as per site requirement. The scope shall include cutting to required length, lowering, fixing, securing and testing as per direction of the Engineer-in-Charge at site. | — | — | — | 2,81,930 | |
| — | 1000.00 | — | — | ||
| — | 3.00 | — | — |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
EL-LM-25-26-01final.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .