PROVN OF 01 X RATION STORE OF TVDP AND RVTP PANAGARH, C/O OD KOLKTA AND SPL REPAIR TO BLDG NO P-09 (MI ROOM) OF FAD UNDER GE PANAGARH (2ND CALL)

Amount

Dismantling floor hearth or wall tilling including cement mortar bedding, removing rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (un-reinforced) n.exc 15 cm thickness of any description and in any position not otherwise specifically provided complete all as specified and directed.

M&L for PCC 1:4:8, type D2 (using 40 mm graded crushed stone) 75 mm thick, as in sub base complete all as specified and directed.

M&L for 75 mm thick PCC 1:2:4, type B1, (using 20 mm graded crushed stone), as in sub base for receiving floor finish with nominal reinforcement complete all as specified and directed. (Note :Reinforcement will be measured and paid seperately)

M&L for Non Skid ceramic coloured tiles 7mm to 8mm thick, (square or rectangular) area of each tile exc 0.18 Sqm but n. exc 0.38 sqm in floors etc , over & including 15 mm thick cement mortar (1:6) screed etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match, complete all as specified. Note: Design, shade and pattern of fixing of tiles shall be as directed and approved by GE

M&L for non skid ceramic tiles coloured 7 to 8 mm thick(square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in vertical surfaces such as skirting etc, set and jointed with neat cement slurry and pointed in white or coloured cement with pigment to match the shade of tiles over and including 10mm thick screed in cement mortar (1:4) complete, all as specified complete all as specified and directed. Note: Design, shade and pattern of fixing of tiles shall be as directed and approved by GE

M&L for glazed ceramic coloured tiles in vertical surfaces of size 350x250x7mm/450x600x7mm thick as on skirting , dados, walls etc set and jointed in neat cement slurry and pointed in white cement with pigment to match the shade of tiles over and including 10mm thick rendering in cement mortar (1:4), complete all as specified and directed. Note: Design, shade and pattern of fixing of tiles shall be as directed and approved by GE

M&L for fly ash brick straight or curved on plan exc 6 mtr mean redious built in CM (1:6) ,including demolition of brick work built in cement mortar including all quoins, arches, pillar etc complete all as specified and directed.

Demolition of cement concrete (Reinforced) as in ground floors and pavings not exceeding 15 cm thick below or above ground level complete all as specified and directed.

M&L for RCC M-25, (using 20 mm graded stone aggregate) Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as speicified and directed.

M&L for RCC M-25, (using 20 mm graded stone aggregate) Beams, cantilevers, bressummers, lintels over 1.5m span complete all as speicified and directed.

M&L for RCC M-25, (using 20 mm graded stone aggregate) as in chajja complete all as speicified and directed.

M&L for RCC M-25, (using 20 mm graded stone aggregate) Fins, fascias, louvres, parapets, and railings exc. 60cm in height, newels, balustrade, and the like complete all as speicified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished surface of concrete complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunch?ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc for fair finished surface of concrete complete all as specified and directed.

Use and waste Formwork to chullah hoods, chajjas, troughs and similar items including edges for fair finished surfaces complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; n.exc 200mm thick (Horizontal or sloping) for fair finished surface of concrete complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for TMT steel bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for TMT bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups, spacers and binders complete all as specified and directed.

Taking down cement plaster, any description on brick or stone walls and ceiling ,chajja, landing etc including racking of joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for two coats of high performance SBR based multipurpose polymer sika latex power or its equivalent make as per manufacturing instruction including rendering 15mm thick in on fair faces of brick work or concrete surfaces finished even and fair on walls in cement mortar (1:4), complete all as specified and directed.

Supply only Integral water proofing compound, complete all as specified and directed. (Makes : Pidilite Industries/ Impermo/Snowcem India Ltd/Sika)

M&L for two coats of high performance SBR based multipurpose polymer sika latex power or its equivalent make as per manufacturing instruction including Rendering 15 mm thick on other than fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar (1:6), complete all as specified and directed.

M&L for rendering 5 mm thick in CM (1:3) on ceiling finished even and smooth without using extra cement etc complete all as specified and directed.

M&L for two coats of high performance SBR based multipurpose polymer sika latex power or its equivalent make as per manufacturing instruction including Rendering 5 mm thick on fair faces of concrete surfaces, finished even and smooth on ceiling/chajja/pillar in cement mortar (1:3), complete all as specified. complete all as specified and directed

M&L for two coats of Oil bound distemper on newely wall surface over a coat of alkali resistant primer including wall care putty for smoth finishes preparation complete all as specified and directed

M&L for complete removal of existing treatment and applying two coats of Oil bound destemper on old wall surface over a coat of chalk whiting primer complete all as specified and directed

M&L for applying three coat of white wash on ceilling new surface of complete all as directed by Engr-in-Charge

M&L for applying two coat of white wash on ceilling old surface of complete all as directed by Engr-in-Charge

M&L for treatment of wall & applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004 , alkali & fungal resistance, dirt resistance exterior paint of required shade (Company depot tinted) with silicon additives@ 1.43 litre/10sqm over and including priming coat of alkali and fungal resistance exterior primer applied @ 0.90 litre/10 sqm including a coat of putty 1 mm thick plastered surface to prepare the surface even and smooth for smooth finish over new surfaces complete all as directed by Engr-in-Charge

M&L for complete removal of extg treatment from wall & applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004 , alkali & fungal resistance, dirt resistance exterior paint of required shade (Company depot tinted) with silicon additives@ 1.43 litre/10sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over old surfaces complete all as directed by Engr-in-Charge

Taking down chowkhats or frame not exceeding 1.5 Sqm each with shutter(s) (without taking off shutters from the frame), complete all as specified and directed

Taking down chowkhats or frame exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter(s) (without taking off shutters from the frame), complete all as specified and directed

M&L for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50X100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp?ressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardan and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and as directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid decorative panelled decorative flush door shutter one side plain on other side of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) complete all as specified and as directed.

S&F factory made single extruded WPC (Wood Polymer Composite) wire gauzed i.e. panel will be wire mesh in lieu WPC , the wire gauze shall be warped on additional square 8mm MS Solid tube and this tube shall be welded to MS frame complete all as specified and as directed.

S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm PVC sheet reinforced suitable for solid PVC door suppling & fixing in opening, complete all as specified and directed

S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC'C' channel having a PVC sheet strip of 20mm width stuckinside solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail & bootom rail; paneling of plain clour PVC sheet to be fitted in the M.S frame welded/ sealed to the stieles & rails with suitable PVC sheet beading, and joining together with solvent cement, supplying & fixing in the frame at site as per specification.complete all as specified and directed.

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured lor payment purpose.) (A) Area not exceeding 2.00 sqm each complete all as specified.

S&F factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted complete all as specified.

S&F Aluminium wire mesh 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminiun beads complete all as specified and directed.

S&F 4.0mm thick Sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F 4.0mm thick Sheet glass, ordinary quality and glazing with oil putty in square but exc 0.5 sqm in each pane complete all as specified and directed.

S&F in repair Aluminium Curtain Rods 25mm dia Decorative type with a pair of brackets, approved pattern and colour, complete all as specified and directed.

S&F Aluminium, anodized barrel tower bolts of extruded section and fixed, 150 mm long, dia of bolt not less than 10 mm, ISI marked, complete all as specified and directed.

S&F 150 mm long alluminium anodised handles complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled Stainless steel and fixed with screws or with welding to existing MS frames, 100 mm size, ISI marked, complete all as specified and directed.

S&F Aluminium alloy, anodised, 300 mm long sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 150 mm long Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) (excluding flushing cistern & flush pipe) complete all as specified and directed.

S&F in repair 10 ltr capacity PVC flushing cistern syphonic action type white dual flush ISI (IS 7231) marked with flush pipe of polythelene of low or high density pvc 32 mm dia complete with all fixing arrangements complete all as specified and directed.

S&F in repair for Vitreous china wash hand basin (630X450mm) white, flat back excluding taps, waste chain and plug and porcelain stopper but including brackets complete all as specifed and directed.

S&F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F PVC (SWR) 110 mm dia pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F Tubes 15 mm bore, ‘medium grade’, galvanized with all fittings and fixed complete to walls and ceilings or laid in floors, including taking up or down steel tubing complete all as specified and directed.

Material (except tubes) and labour for 15mm dia GI tubing medium grade with all fittings to walls, ceiling or laid under floors including taking up or down steel tubing and connections 15 mm bore complete all as specified and directed.

S&F in repair 15mm bore pillar taps cast copper alloy,with capstan heads,chromium plated,screwed down, fancy type high pressure, with or without lettred 'HOT or COLD' with long screwed sunk and fly nuts complete all as specified and directed.

S&F in repair CP Stop valve, any description, suitable for 15mm bore pipe complete all as specified and directed.

S&F in repair Bib taps, cast copper alloy with handle, chromium plated fancy type, long body with wall flange screwed down, suitable for 15 mm bore pipe complete all as specified and directed.

S&F in repair tubular towel rail /towel ring 20mm dia D type and 60cm long between flanges of brass chromium plated complete all as specified and directed.

S&F in repair Waste coupling of PTMT, for WHB any colour half or full threaded suitable for 32 mm size discharge pipe (Minimum weight 45 gm) in repair, complete all as specified and directed.

S&F in repair Cast iron 'P' or 'S' trap, ISI marked, suitable for 100 mm bore CI spun pipes, complete all as specified and directed.

Dismantling of cast iron pipes with all fittings and fixing acessories, jointed in cement mortar 75/100 mm bore, at any location, complete all as specified and directed.

S&F 150 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls for all complete all as specified and directed.

S&F in repair 150 dia PVC (SWR) plain bends bends any radius with complete all as specified and directed.

S&F in repair Grating with or without hole of PTMT (Minimum weight 25 gm) and fitting of shade matching to tiles/floor, fixed with white cement including matching shade pigment, complete all as specified and directed.

M&L for 15 mm Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete over and including 15mm thick Screed bed or backing coat for laying floor finishes in CM 1:6 all as specified and directed.

M&L for Green Marble work 15 mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of following types over and including 15mm thick Screed bed or backing coat for laying floor finishes in CM 1:6 complete all as specified and directed.

M&L for Two coats of synthetic enamel paint over & including a coat of red oxide primer over new steel & iron surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-1 (using 20mm gradede crushed stone aggregate) as in plinth protection finished even and smooth without using extra cement, incl making joints 10mm wide to the full depth of PCC at every 3 meters and at every change of direction and filling the same with and incl bitumen and sand 1:3 by weight complete all as specified and directed.

M&L for PCC 1:3:6 type C1 (using 20mm garded stone aggregate) as in surface channel complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

M&L for repair to crack portion with jacktting technuque, taking down existing plaster up to brick wall surface of min 200 mm wide, cleaning to loose particles on surface of brick work along the length of crack and filling the gap/crack area with PCC 1:1.5:3 type A0 using 12.5 mm aggregate up to brick surface and inserting the welded mesh of size 25 x 25x 2 mm dia along the crack on both side of the wall surface fixed with, drilling holes 10 mm dia on either side of the crack by means of drilling machine through out the full width of the wall @ 25 cm c/c and insert 8/10 mm dia rod in the drilled holes, welded with horizontal rod to with hold the welded mesh and applying grit plaster 1:1:2 using 4 mm and down aggregate finished even and smooth without using extra cement complete all as specified and directed. (Note: Reinforcement and welded mesh will be measured and paid separately )

S&F in repair Door closer hydraulically regulated, alluminium body, designation No. 3 universal type, suitable for door shutters upto 851 to 1000 mm in width and of weight between 60 to 80 kg, ISI marked, complete all as specified.

M&L for Providing precast cement concrete type B-0 1:2:4 with (using 12.5 mm graded aggregate) louvres and jallies, 25mm thick (mea sured solid), including all mould- ings but excluding frame (Pre cast frame shall be measured separately and paid for under item set in CM (1:4) complete all as specified and directed.

S&F in repair Vitreous China Urinal, Half stall type, white including urinal spreader, 32 mm urinal coupling & necessary fittings ,complete all as specified and directed.

M&L for 40 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in roof padding, finished fair and even without using extra cement from roof surfaces complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces on roof surfaces of concrete surfaces in cement mortar 1:4 complete all as specified and directed.

M&L for providing water proofing treatment with a layer of APP based polymeric membrane, 3 mm thick (minimum), weighing not less than 3.60 kg/Sqm reinforced with polymer non woven fabric (weighing not less than 160 gm/ Sqm) shall be applied over one coat of cold bituminious primer @ 0.40 ltr/ Sqm ( membrane shall be laid using butane torch and sealing all joints etc, complete all as specified and directed . (Note: The overlaps shall be of minimum 75 mm on longitudinal direction and 100 mm on transverse direction)

M&L one coat of aluminium paint over APP membrane complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil Complete all as specified and directed.

Surface dressing n exc 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches in soft/loose soil n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and getting out Complete all as specified and directed.

Removing surplus excavated spoil/earth to a distance not exc.50M and deposited where directed at a level not exc.1.5 M above the starting point Complete all as specified and directed.

Returning filling in soft /loose excavated soil including spreading leveling watering and well ramming in layers not exceeding 25 CM complete all as specified and directed.

M&L for sand filling filling in floors or pavings, laid in layers n exc 15 cm thick, spread, levelled and blinded with earth and rammed incl watering complete all as specified and directed.

M&L for hardcore of broken stone or boulder of gauge n exc 63mm deposited, spread & leveled in lyers n.exc 15 cm thick watered & rammed to a true surface complete all as specified and directed.

M&L for Plain Cement Concrete Type D2 14:8 (using 40 mm graded stone aggregate) as foundation and mass filling complete all as specified and directed.

M&L for M-25 Design mix (using 20mm stone aggregate Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for M-25 (Design mix) using 20mm stone graded aggregate Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions for fair finished surface of concrete complete all as specified and directed.

Formwork to chullah hoods, chajjas, troughs and similar items in?cluding ege for fair finished surface of concreted complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in Damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&Lfor Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) separately) complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer Composite) wire gauzed i.e. panel will be wire mesh in lieu WPC , the wire gauze shall be warped on additional square 8mm MS Solid tube and this tube shall be welded to MS frame complete all as specified and as directed.

Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gaskey, etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

M&L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for 75 mm thick, Cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base complete all as specified and directed.

M&L for 75 mm thick PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in floor with nominal reinal reinforcement finished even and fair complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 15 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over 20mm thick screed bed in cement mortar (1:6) complete all as specified and directed.

M&L for Kota stone slab 15 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with ditto as per item 39 , over a backing coat 10mm thick in CM (1:3) complete all as specified and directed.

M&L for two coats of acrylic distemper over a coat of alakali rsistant primer on walls on newly plastered surfaces including preperation complete all as specified and directed.

Excavation over areas n.exc 1.5m depth and getting out in soft/loose soil complete all as specified and directed.

M&L 100 mm thick, Cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc 15 cm thick, spread, levelled and blinded with earth and rammed incl watering complete all as specified and directed complete all as specified and directed.

M&L for PCC 1:3:6 type C1 as in lintels / beam upto 1.5m clear span, and other similar bands, copings, kneelers, apex stones, bed plates, kerbs and haunching/ benching, water troughs and the like including weathering, slightly rounded or chamfered ang complete all as specified & directed

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigments complete all as specified and directed.

M&L for PCC 1:3:6, D2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete all as specified and directed

M&L for Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius, built in CM 1:4 with Old size bricks complete all as specified and directed.

M&L for RCC 1:2:4 type B1 using 20mm stone aggregate as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar art set in CM (1:6) complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar (1:4) on wall surface and finishing even and fair complete all as specified and directed.

E/M PORTION Taking down carefully aluminium conductor point wiring (light , fan, socket or powr) complete including fittings such as switches, ceiling rose, pendents, regulators sockets etc and removing (except those to be reused shall be kept in safe custody at the site) andmaking good disturbed surfaces of walls, floors etc tomatch with the existing completeall as specified and directed.

M&L for point wiring for light point/ fan point, one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including pressed steel terminal switch boxes, 3 mm thick bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLSH PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed.

All as per item No.118.00 above but One 3 pin 5 Amps socket out let points on independent board complete all as specified and directed.

All as per item No.118.00 above but 5 Amp socket on same board with other switches complete all as specified and directed.

All as per Item No 118.00 above but for one calling bell point controlled by one one way Bell switches complete all as specified and directed.

M&L for wiring for socket out let on independent Boards controlled by one, one way switch using 4.0 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including pressed steel terminal switch boxes , 3 mm thick bakelite sheet top cover (ISI Marked) fitted with Chromium plated brass screws & washers and 4.0 sqmm nominal cross sectioanl area multistranded copper conductor , PVC insulated unsheathed FRLSH cable earth wire and connecting to earth dolly and brass screws, washers etc.complete all as specified and directed.

S&F switch piano flush type, single pole, 5/6 Amps, one way complete all as specified and directed.

S&F switch socket combination 2 in 1 multipurpose 5 pin, (6 Amps) flush type controlled by one switch complete all as specified and directed.

S&F socket outlets 2 in 1, 5 pin, 5/6 Amps flush type 230/240 V complete all as specified and as directed

S&F switch socket combination 5 in 1, 6 pin, (5/16 Amps) flush type controlled by one switch complete all as specified and directed.

S&F ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified and directed.

S&F stepped type electronic fan regulator flush type 240 Volts ISI marked complete all as specified and directed.

S&F lamp holder, PVC/polycarbomate type with back plate straoght of angle suitable for LED lamp complete all as specified and directed

S&F Turbo 12 watt inverter LED lamp 12 watt of capacity 220 - 240 volts, 50 Hz complete all as specified and directed Make- Bajaj/Surya/Havells/Crompton

S&F Bell push switch, flush type, 5 amp complete all as specified and directed.

S&F Buzzer, Ding dong, AC 230 Volts, single pole 230 volts complete all as specified and directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

S&F submain two single core 4 sqmm nominal cross sectional area multistranded copper conductor FRLSH cable PVC insulated unsheathed 1100 volts grade drawing in and suitable size PVC conduit (ISI Marked) concealed including 4 sqmm nominal cross sectional area multistranded copper conductor FRLSH cable, PVC insulated unsheathed 1100 volts grade earth wire complete all as specified and directed.

S&F submain two single core 6 sqmm nominal cross sectional area multistranded copper conductor FRLSH cable PVC insulated unsheathed 1100 volts grade drawing in and suitable size PVC conduit (ISI Marked) concealed including 6 sqmm nominal cross sectional area multistranded copper conductor FRLSH cable, PVC insulated unsheathed 1100 volts grade earth wire complete all as specified and directed.

S&F wall LED security light fittings 35 watt, 230 volts, minimum lumn output 100 lumen/watt, made up ofpressure dia cast housing with prismatic polycarbonate difuser and industrial LED with secondary optic and IP-65/66 including neccessary connection complete with all accessories including connected with 3 core copper cable of suitable 1.5 sqmm size complete all as specified and directed.

S&F LED light fitting 1 x 20 watt box type with same make LED tube rod side connection AC decorative boxype 4' long wih driver, holder including LED tube connecting up with complete all accessories andconnection from ceiling rose with twin core twisted flexible copper conductor cable withsuitable size and earthing complete all as specified and directed.

S&F LED battem mirror light fitting 1 x 10 watt box type, Polycarbonate, cool day light, 6500K,1000 lumens with accessories complete all as specified and directed. Make CC/Crompton/ Havells/ Jaguar/Bajaj

Supply only ventilating metalic body exhaust fan 300 mm sweep 230 volt AC, heavy duty complete with louver and all accessories including cutting hole of suitable size, making good surface by doing plaster and applying two coat of distemper complete with fixing arrangement to wall connected with twin core twisted flexible copper conductor (23/.0076) of suitable size all as directed.

S&F epoxy powder coated sheet metal Vertical distribution board double door TPN DBs, 4 ways, with IP-43 multipurpose outgoing suitable for munting 63 Amp as incomer with Bus Bars , neutral links with all accessories complete all as specified and as directed.

S&F MCCB 4 pole, 415 volts of capacity 63 Amps with breaking capacity of 16 KA fixed thermal and fixed magnatic setting including necessary connection complete all as specified and as directed

S&F MCB 4 pole, 415 volts fixed type 63 Amps, with breaking capacity 16 KA complete including necessry connection all as specified and directed.

S&F epoxy powder coated sheet metal enclosure for DBs, single door, Single pole and neutral, 8 ways, with mounting fitted with 200 Amps rated bus bar, DIN channel, neutral link and incoming contact complete all as directed.

S&F MCB SPN 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed.

S&F MCB SP 6-32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed.

M&L for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion.

Taking up or own carefully steel tubing 25 mm bore with all fittinge including gate valve from in ternches, wall, floor & ceiling and kept in safe custody at site for refixing of GI pipe complete all as specified and as directed. (Note: Excavation and earthwork will be measured and paid separately)

S&F Pipes galvanized, 25 mm bore “Medium grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement or specified.

S&F in repair gun metal, gate valve, 25 mm dia with iron wheel head, screwed both ends for iron pipe and fix complete all as specified and directed.

S&F in repair capacity 1000 Ltrs rotational moulded polyethylene water storage tanks (Cylindrical, vertical with closed top) confirming to relevent IS complete including provision of all inlet outlet overflow and drain pipe fitting including taking down complete all as specified and directed by Engr-in-Charge Make : Vectus/Sintex/Prayag

S&F high pressure PTMT float valve with epoxy coated alluminium rod and high density polythelene ball screwed for iron pipe 25 mm dia with fly nut complete all as specified and as direced.

M&L for cutting existing steel tubing for alternation or addition of size 40 to 50 mm dia GI pipe complete all as specified and directed.

Supply, laying, connecting, testing and commissioning of LT under ground cable XLPE insulated, aarmoured heavy duty electric cable with aluminium conductor , 1100 vlts grade , cross sectional area 16 sqmm 4 core including taking out in trenches complete all as specified and directed Note:- (i) Excavation,sand cushioning,brick will be measured and paid separtely.

M&L for river sand, washed and screened dry for cushioning to under ground cable in trenches below and around under ground cable including spreading and levelling complete as specified and directed . Note :- Punned thickness 18 cm shall only be considered for payment

Supply and lay in trenches fly ash bricks, for cable protection all as specified and directed by the Engr-in-Charge.

S&F Pipes galvanized, 50 mm bore “light grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement or specified complete as specified and directed

S&F ventilating exhaust fan 380 mm sweep 230 volt AC complete with louver and all accessories including cutting hole of suitable size, making good surface by doing plaster and applying two coat of distemper complete with fixing arrangement to wall connected with twin core twisted flexible copper conductor (23/.0076) of suitable size all as directed.

Supply, laying / fixing /connecting, testing and commissioning of LT under ground cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cable (heavy duty) with multistranded aluminium conductor,1100 Volts grade in trenches/on wall/poles laid in ducts/inside protection pipe of the following cross sectional area including cable glands,lugs and suitable size of MS saddle clips (where ever cable laid in ceilings / walls without cable duct) all as directed by the Engr-in-Charge for the following ratings Note:- (i) Excavation,sand cushioning,brick will be measured and paid separtely. (a) 10 Sqmm x 2 core

Jaibalaji Enterprise (BID ID -3144823)

M/S SUSHMA INFRA PROJECT AND POWER (BID ID -3145013)