ADDITION ALTERATION TO GALLERY SANITARY DOMESTIC SEWAGE FRESH WATER LINE AND ALLIED WORKS AT INS VAJRABAHU A14 AT N DYD SPECIAL REPAIR OF FOUNDRAY SHOP FOR WALL REPAIR AND HEAT RESISTANCE PAINT APPLICATION IN FURNANCE AREA C NO 41 BEF NAVAL DOCKYARD

Amount

Supply & Fixing in repairs 160 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, ceilings or in floor etc with and including fixing clips bends elbow, shoes bends etc (Note :- Measurement shall be taken along the centre line of the pipes) complete all specified and directed by Engr-in-Charge.

Supply & Fixing in repairs 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls/floor including fixing clips, bends, elbows, shoes etc complete all specified and directed by Engr-in-Charge.

Supply & Fixing in repairs 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall/floor complete all specified and directed by Engr-in-Charge.

Supply & Fixing for PVC (SWR) bends any radius 160mm bore complete all specified and directed by Engr-in-Charge.

Supply & Fixing for PVC (SWR) bends any radius 110mm bore complete all specified and directed by Engr-in-Charge.

Supply & Fixing for PVC (SWR) bends any radius 75mm bore complete all as specified and as directed by Engr-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing ) and removing debris outside MD land complete all as specified and as directed by Engr-in-Charge.

Demolition of RCC in roof floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and pavings n exc 15 cm thickness (below or above ground level) and removing debris outside MD land complete all specified and directed by Engr-in-Charge.

Material & Labour for kota stone slab 20 to 25mm thick in steps, jambs, pillars, window sides, jambs, cills and cooking platform and like laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over a backing coat 10mm thick in CM (1:4) complete all as specified and as directed by Engr-in-Charge.

S & F in repairs PVC SWR floor trap 75mm, plain with grating including setting and jointing with solvent cement fixed complete all as specified and as directed by Engr-in-Charge.

Supply & Fixing in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed by Engr-in-Charge.

Supply & Fixing in repair 15 mm dia fancy type pillar tap cast copper alloy with capston heads chromium plated screwed down high pressure with or without hot or cold with long screws shanks and fly nuts screwed for iron pipes complete all specified and directed by Engr-in-Charge.

Supply & Fixing in repairs 15 mm bore dia of pipe, brass chromium plated fancy type bib tap complete all as specified and as directed by Engr-in-Charge.

Taking down 15 mm bore, GI tubing and connections complete all as specified and as directed by Engr-in-Charge.

Taking down 20 mm bore, GI tubing and connections complete all as specified and as directed by Engr-in-Charge.

Taking down 25 mm bore, GI tubing and connections complete all as specified and as directed by Engr-in-Charge.

Taking down 40 mm bore, GI tubing and connections complete all as specified and as directed by Engr-in-Charge.

S&F 15 mm bore GI tubing medium grade with all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc fixed to walls and ceilings with suitable size GI clamps or laid in floors complete all as specified.

S&F 20 mm bore GI tubing medium grade with all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc fixed to walls and ceilings with suitable size GI clamps or laid in floors complete all as specified.

S&F 25 mm bore GI tubing medium grade with all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc fixed to walls and ceilings with suitable size GI clamps or laid in floors complete all as specified.

S&F 40 mm bore GI tubing medium grade with all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc fixed to walls and ceilings with suitable size GI clamps or laid in floors complete all as specified.

Demolition of brick work or stone/boulder masonry, built in cement mortar, including all quoins, arches, pillars etc, but excluding ashlar facings, dressed stone work & precast concrete articles including copings etc.and removing debris outside MD land complete all as specified. Note: The place of disposal shall be find out by the contractor.

Material & Labour for Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and as directed by Engr-in-Charge.

M&L for brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick wall in cm (1:4) complete all as specified.

Material & Labour for preparing cement/concrete surface and applying two coats of acrylic cementitious waterproof coating two coat over a primer complete all specified and directed by Engr-in-Charge.

Material & Labour for PCC (1:2:4) type B-1 (Using 20mm graded stone aggregate) as in roof/chajja padding for maintaining slope complete all specified and directed by Engr-in-Charge.

Material & Labour for PCC 1:2:4 type B1 using 20 mm graded stone aggregate as in foundation of poles complete all specified and directed by Engr-in-Charge.

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removing debris outside MD land. Note: The place of disposal shall be find out by the contractor.

Material & Labour for rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finishing the surface even and smooth without using extra cement complete all specified and directed by Engr-in-Charge.

Material & Labour for preparation of new plastered surfaces of wall & ceiling and applying two coats of oil emlusion distemper over a coat of 3mm thick wall care putty and alkali resistant primer complete all as specified.

Material & Labour for preparation of new plastered wall surfaces, over 10cm width of girth and applying two coats of 100% acrylic exterior grade weather resistant emlusion over a coat of primer complete all as specified and as per manufacturer's instructions complete all as specified and as directed by Engr-in-Charge.

Material & Labour for Rendering 20mm thick on fair faces of brick work or concrete surface with two coats i.e. (15mm thick back coat in CM (1:6 and 5 mm thick finishing coat in cement mortar 1:4 ) and finished even and smooth without using extra cement including all safety measures and scaffolding upto any height complete all specified and directed by Engr-in-Charge.

Material & Labour for preparing old decorated wall surfaces with complete removal of existing finish over 10cm width or girth and applying two coats of 100% acrylic exterior grade weather resistant emlusion over a coat of primer complete all as specified and as per manufacturer's instructions complete all as specified and as directed by Engr-in-Charge.

Material & Labour for preparation of new steel surfaces exc 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all specified and directed by Engr-in-Charge.

Supply only integral water proofing compound complete all as specified and as directed by Engr-in-Charge.

Material & Labour for Bitumen membrane 3 mm thick laid over a coat of bitumen primer @ 0.30 to 0.50 Kg per Sqm in floors and vertical surfaces of sunken slab in toilet complete all specified and directed by Engr-in-Charge.

Material & Labour for Applying evenly a tack coat of industrial bitumen 85/25 grade at the rate of 1.2 kg per sqm including cleaning surface complete all specified and directed by Engr-in-Charge.

Cutting into existing manholes for connecting new drains for 150 mm dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and as directed by Engr-in-Charge.

Excavation in trenches not exc 1.5 m wide and n exec 3m deep in for foundation etc getting out in hard dense soil complete all as specified and as directed by Engr-in-Charge.

Removing excavated material exc 50m and n.exc 250m and depositiing where directed at a level n.exc 1.5m above the starting point complete all specified and directed by Engr-in-Charge.

Returning and filling in, including spreading, levelling, watering and well rammed in layers not exec 25 complete all as specified and as directed as in hard/dense soil complete all specified and directed by Engr-in-Charge.

Material & Labour for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in concrete bed to 150 mm bore pipe including packing under and haunching against the sides of pips after they are laid and tested complete all specified and directed by Engr-in-Charge.

Supply and fix structural steel framed works such as angle, channel, grating, gate, ladder, parline, rafter, grating etc. fixed with connecting plates including as in supporting structure of duct, drain edge etc Confirming to Fe-290, E-165 complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed by Engr-in-Charge.

Material & Labour for POP false ceiling using 600X900x12 mm thick plaster of paris with gypsum binder sheet decorative type and necessary provision for concealed type light fittings, fixed on 22 gauge GI channel grid work, main joist of size 50x25 mm spaced at 750 mm centre, secondary joist of size 75X20 mm fixed to main joists spaced at 900mm, suspended to roof members using 25x25x2 mm GI angles and fasteners @ 1.2 mtr c/c complete all as specified and directed by Engineer-in-Charge.

Taking down chowkat with shutters (without taking off shutters from the frames) area exc 1.5 Sqm but n.exc 4 Sqm each.

S&F powder coated aluminium sections for partitions, windows, ventilators and doors including fabrication of frame/shutters and fixing to walls/floors with necessary lugs, cleats etc including all accessories such as glazing clips, handles, tower bolts, rollers rubber beadings for fixing glass panes in frame including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required complete all as specified Note: - (i) Glass panes will be measured & paid separately. (ii) Rubber beading will not be weighed and paid separately (iii) Minimum thickness of powder coating shall be 25 micron.

Material & Labour for rendering 5 mm thick in CM 1:3 mixed with waterproofing compound on fair faces of concrete surfaces in ceiling and finishing the surface fair and even complete all specified and directed by Engr-in-Charge. Note- Integral water proofing compound shall be measured and paid seperately.

Material & Labour for preparation of plastered surfaces of wall and applying two coats of plastic emulsion paint over a coat of primer complete all specified and directed by Engr-in-Charge.

Material & Labour for applying wall care putty not less than 2mm thick on wall surfaces and finished even and smooth complete all specified and directed by Engr-in-Charge.

Material & Labour for preparing wood and wood based surfaces of any description, width or girth and applying two coats of synthetic varnish over a coat of wood filler complete all as specified and directed by Engr-in-Charge.

Material & Labour for preparing new wood and wood based surfaces of any description, width or girth and applying three coats of french polish over a coat of wood filler complete all as specified and directed by Engr-in-Charge.

Supply and fixing wall panelling made out of 12mm thick pinewood planks with tongue and grove edges for a seamless look with melamine/ venner laminated finish and installed by using strut framework system. Slates to be backed with synthetic PF 10 x 25 adhesive to wall with stick. The support system, suspension system shall be as per manufacturers instructions and panelling shall be finished as directed by Engg-in-Charge.

M & L for 12mm thick toughened glass door , double shutter including providing SS pivots, door closer, SS corner supports as required, SS handle 600mm long fixed on both shutter, SS studs 1200mm long, locking arrangement and necessary SS accessories like clamps as required at site complete all as directed.

Supply & Fixing 8mm thick glass oneside visible and glazing in squares with and including fitting, fixtures and beading etc complete all as specified and directed by Engr-in-Charge.

Supply & Fixing in repair Porbandar or Malad stone cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.25 sqm area and not exceeding 0.5 sqm fixed with and including one number SS clamps (grade -202) made out of 30mm X 2mm flat, 150mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatment complete all as specified and directed by Engr-in-charge.

Supply & Fixing in repair double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all specified and directed by Engr-in-Charge.

Material & Labour for perforated vinyle graphics stickers having departmental logos engraving on glass. complete all as specified and directed by Engr-in-Charge.

Material & Labour for preparation of old decorated surfaces of wall and applying one coat of oil emulsion distemper complete all specified and directed by Engr-in-Charge.

Material & Labour for preparation of old painted wooden of any description over 10cm width or girth and applying one coat of synthetic enamel paint incl necessary scaffolding complete all specified and directed by Engr-in-Charge.

Material & Labour for Second class hardwood Plain fillets exc 3 Sqcm but nexc 6 Sqcm, square,rectangular or triangular in section, clean sawn, secured with screw complete all specified and directed by Engr-in-Charge.

Material & Labour for first class hardwood n exc 3 Sqcm bullnosed, splayed, chamfered or rounded on one edge or face complete all specified and directed by Engr-in-Charge.

Supply & Fixing second class hardwood, plain solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all specified and directed by Engr-in-Charge.

Material & Labour for mild steel bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all specified and directed by Engr-in-Charge.

Material & Labour for Veneered decorative plywood 12 mm thick, grade 1 (with BWR resin) with decorative face veneers on one faces; fixed with screws to timber frame work complete all specified and directed by Engr-in-Charge.

Removing Bldg Material exc 1.5 Km but n.exc 15 Km and depositing outside MoD land complete all specified and directed by Engr-in-Charge.

Supplying, fitting and fixing 12mm thick Laminated wooden Flooring Work conforming to EN13329:2006 with plank size not Iess than 1200 mm X 190 mm (with unilin/tongue-groove locking arrangement) having 0.2mm thick top abrasive layer over a decorative layer followed by a High-density fibreboard (HDF) having density > 850 kg/m3 substrate core over a rasin saturated backing layer and installing through unilin or tongue- groove system (having locking strength not less than 1000 kg/m) over a 2 mm thk underlayer polyurethene foam on polythene sheet 250 micron, over a smooth, flat, hard subfloor free from moisture (< 8%), grease etc. complete in all respect with requisite accessories like end profile, transition profile, reducer 'T' profile etc. wherever required and preparation of base including all other incidental works as per direction & satisfaction of Engineer in charge. Cost of Laminate Floor Accessories only (Skirting ,End edge, T- moulding,Reducer) shall have to be added separately,wherever required complete all specified and directed by Engr-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for and removing debris out side MD land. Note: The place of disposal shall be find out by the contractor.

Material & Labour for cement concrete 1:3:6 type C2 (using 20 mm graded stone aggregates) in foundations, filling and mass concrete. complete all specified and directed by Engr-in-Charge.

Material & Labour for rendering 20 mm thick pre polymer modified ready mixed cement based plaster in two coats 12 mm thick base coat and 8 mm thick finishing/final coat. Polymer modified ready mixed cement based plaster should having minimum composition of cement & sand 1:4 using fully treated dry, well graded natural sand conforming to IS-383 suitable for external plastering having low rebound properties, low water demand for curing properties, mechnical mixing with water in a matalic tray only to made good, consistency as per the specification of the manufacturer and applied over exterior masonry and concrete surfaces incl using richer mix for making corners if necessary incl making grooves of existing size including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions and necessary two legged MS pipe scaffolding as wherever required incl curing required complete all specified and directed by Engr-in-Charge. (Water proofing compound to be measured and paid for separately).

Material & Labour for rendering 10 mm thick pre polymer modified ready mixed cement based plaster on chajja top and soffits Polymer modified ready mixed cement based plaster should having minimum composition of cement & sand 1:4 using fully treated dry, well graded natural sand conforming to IS-383 suitable for external plastering having low rebound properties, low water demand for curing properties, mechnical mixing with water in a matalic tray only to made good, consistency as per the specification of the manufacturer and applied over exterior masonry and concrete surfaces incl using richer mix for making corners if necessary incl making grooves of existing size including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions and necessary two legged MS pipe scaffolding as wherever required incl curing required complete all specified and directed by Engr-in-Charge. (Water proofing compound to be measured and paid for separately).

Supply only Waterproofing chemical complete all specified and directed by Engr-in-Charge.

Material & Labour for applying a coat wall care putty 3mm thick on plastered wall and ceiling surfaces, preparation and applying two coats of heat resistance synthetic enamel paint over a coat of wall primer including necessary scaffolding and safety arrangement complete all specified and directed by Engr-in-Charge. Note : Product having range of heat resistance min 300 Degree Celsius.

Material & Labour for preparation of new plastered surfaces of wall/roof and applying one coat of acrylic (antifungal) exterior grade paint over one coat of primer including necessary scaffolding and safety arrangement complete all as specified and directed by Engineer-In-Charge.

M & L for cleaning and removing the cement slury, dust, dirt, foreign or loose materials contaminants liatance etc. which could effect the bond coating and substrate on the existing treatment by means of wire brush, scrapper etc and applying double layer with super crack sealer for repairing the cracks of the external wall areas complete all as specified and directed by Engineer-In-Charge.

Material & Labour for preparation of old plastered and cracked external wall surfaces and applying two coats of non dilutable Raincoat over a coat of prime seal primer having dft of 110 micron and elongation of >200% as per manufaturers instructions complete as specified and directed by Engineer-in- charge.

Taking down carefully old U/S point wiring copper/Aluminum (light/ fan /sockets/power) complete with switches, sockets, ceiling roses, lamp holders, brackets & other fitting & Fixtures connected, and making good to disturbed surfaces as directed by Engineer-in-Charge

Taking down old U/S tube light fittings single / Twin ,Recess mount fitting , etc and making good the distrubed surface matching with existing surface complete all specified and directed by Engr-in-Charge.

Taking down old u/s MCB DBs complete with MCBs, isolator etc of any type and capacity from wall/ceiling etc & making good to the disturb surfaces all as directed by Engineer-in-charge complete all as specified and as directed by Engr-in-Charge.

Material and labour for point wiring with FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm size 1100 volts grade drawn through and including PVC casing caping not less than 25mm width with all accessories fixed on wall including FRLS PVC insulated, unsheathed multistranded copper conductor cable of size 1.5 sqmm as earth continuty conductor connecting to common earth dolly and PVC moulded box ISI marked for having the switches, switch sockets regulator etc complete all as specified and as directed by Engr-in-Charge for following:- Note:Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

One light point controlled by one switch

One 5 Amps switch socket combination on independent board

One 5A flush type switch socket point on same board

Supply and fixing modular flush box of 3 module

Supply and fixing modular flush box of 6 module

Supply and fixing modular flush box of 1/2 module

Supply and fixing modular cover plate with frame 2 module

Supply and fixing modular cover plate with frame 3 module

Supply and fixing modular cover plate with frame 6 module

Material & Labour for point wiring (Work station for computer) complete with proper colour coding using PVC insulated unsheathed multistranded copper conductor cable 4.0 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked, not less than 25mm casing caping with all accessories such as tee, bends, elbow, reducers, junction box etcfixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 4.0 sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including modular box with cover plate frame in any module complete including necessary electric connection for each workstation point comprising of 03 Nos 6A sockets(2.5 sqmm) and 01 No 15A(4.0 sqmm) socket on same board complete all as specified and directed by Engr in charge Note:Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Material and labour for submain wiring with 2 runs of 4.0sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn through and including non metalic PVC casing caping not less than 25mm width ISI marked including all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 4.0 sqmm PVC insulated unsheathed copper conductor cable as earth dolly complete all as specified and directed by Engr in charge . Note: i) Colour coding shall be as (i) Phase- Red/yellow/Blue (ii) Neutral - Black (iii) Earth - green ii) 2 runs of 4.0sqmm cable for phase , one run of 4.0 sqmm cable for earth and one run of casing caping shall be measured and paid as one Mtr .

Material and labour for submain wiring with 2 runs of 6.0sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn through and including non metalic PVC casing caping not less than 25mm width ISI marked including all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 6.0 sqmm PVC insulated unsheathed copper conductor cable as earth dolly complete all as specified and directed by Engr in charge . Note: i) Colour coding shall be as (i) Phase- Red/yellow/Blue (ii) Neutral - Black (iii) Earth - green ii) 2 runs of 6.0sqmm cable for phase , one run of 6.0 sqmm cable for earth and one run of casing caping shall be measured and paid as one Mtr .

Supply and fixing LED recess mounted type fitting 36W 2'x2' CRCA LED Slim panel with recess mounting, powder coated white CRCA full glow LED panel including control gear and lamp and connecting up with and including three core flexible copper conductor cable of suitable size from ceiling rosecomplete all as directed and specified by Engr-in-Charge.

Supply and fixing switch piano, modular type 1 way 6 Amps 1 module 240 volts flush type complete all as directed and specified by Engr-in-Charge.

Supply and fixing switch piano, modular type 1 way 16 Amps 1 module 240 volts flush type complete all as directed and specified by Engr-in-Charge.

Supply and fixing modular socket 6 Amps 2/3 pin 240 volts AC combined 2 module all as specified and directed by Engr-in-Charge.

Supply and fixing modular socket 16 Amps 2/3 pin 240 volts AC combined 2 module all as specified and directed by Engr-in-Charge.

Supply and fixing fan regulator, modular type 1 way 120W 2 module 240 volts flush type complete all as directed and specified by Engr-in-Charge.

Supply and fixing ceiling rose surface bakelite three terminal of size 60x50 mm,240 Volts AC complete all as directed and specified by Engr-in-Charge.

Supply and fixing in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting TPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as directed. Note : The cost of removing old wooden box and making good disturbed surface i.e. brick work, plastering etc is included in quoted rate.

Supply and fixing in repair Distribution Board double door, prewired type, made out of CRCA mild steel sheet with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection surface mounting SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCB’s and isolators etc complete all as specified and directed by Engr in charge Note : The cost of removing old wooden box and making good disturbed surface i.e. brick work, plastering etc is included in quoted rate.

Supply and fixing MCCB 4pole 100A, 16kA complete all as directed and specified by Engr-in-Charge.

Supply and fixing MCB SP 6 - 32 Amps, 'C' curve 10 KA Rupturing capacity complete all as directed and specified by Engr-in-Charge.

Supply and fixing MCB SP 40-63 Amps, 'C' curve 10 KA Rupturing capacity complete all as directed and specified by Engr-in-Charge.

Supply and fixing MCB SPN 40-63 Amps, 'C' curve 10 KA Rupturing capacity complete all as directed and specified by Engr-in-Charge.

Supply , fixing, testing in repairs of JEF ECO SAFE Maintenance Free Grounding Solution set comprising of High tensile low carbon steel rod of 3 Mts length & 25 mm dia with 250 micron ( avera Schneider ) molecularly bonded copper on the outer surface to confirm with requirements of UL467 along with Back-fill compound strictly be a Carbon based conductive concrete type which has a resistivity of less than 0.12 Ohm Mtr as per Clause 14.5 D of IEEE : 80 standard. Back-fill compound should be electronically conductive ( Like in metals ) and should not depend on moisture for conduction. JEF Powerfill Loresco compound shall be supplied in 50 Pound Bag. (1 Bag of 50 Pounds required per earthing set). Back-fill comound should be environment friendly, should solidify when mixed with water and set like concrete and should not leach / diffuse into the ground. A suitable earth terminaton clamp should also be supplied along with the set alongwith earth pit weatherproof complete all as specified and directed by Engr in charge Note : Back-fill compund shall not be mixed with any soil while pouring in the bore hole.

Material and labour for 4mm dia GI wire earth continuity conductor or main earthing lead fixed to wall or buried in ground and fixed to panel/transformer through and including 20mm GI pipe light grade for protection complete all as specified and directed by Engr in charge

Supply and fixing round shape 12 watt 220V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr in charge

Supply and fixing LED flexible strip light ,powder coated white CRCA full glow including DC driver including all accessories required for fixing on arc.complete all as specified and directed by Engr in charge

Supply and fixing fresh air grill made of GI 20 gauge with blade with volume control damper complete all as specified and directed by Engr in charge

Material and labour for fire damper made out of GI sheet 16 gauge with fusible plug complete all as specified and directed by Engr in charge

Material and labour for point wiring complete with PVC insulated unsheathed multistranded copper conductor cable 2.5 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including heavy grade stove enamelled steel conduit not less than 25mm dia with all accessories such as tee, bends, elbow, reducers, junction box etc fixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 2.5sqmm size, 1100 volts, ISI marked, FRLS grade as earth continuty conductor connected to common earth dolly with and including modular box with cover plate frame in any module complete for 15A switch socket combination on the independent board complete all as specified and directed by Engr in charge. Note:Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Material and labour for point wiring with FRLS PVC insulated unsheathed multi stranded copper conductor cable of 1.5 sqmm size 1100 volts grade drawn through and including PVC condduit not less than 20mm dia with all accessories fixed on wall including FRLS PVC insulated, unsheathed multistranded copper conductor cable of size 1.5 sqmm as earth continuty conductor connecting to common earth dolly and PVC moulded box ISI marked for having the switches, switch sockets regulator etc complete all as specified and as directed by Engr-in-Charge for following:- Note:Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

One light point controlled by one switch

One fan point controlled by one switch and regulator

One 5 Amps switch socket combination on independent board

One 5A flush type switch socket point on same board

Material & Labour for point wiring complete using PVC insulated unsheathed multistranded copper conductor cable 4.0 sqmm size, 1100 volts ISI marked, FRLS grade drawn through and including non metalic rigid, double lock, ISI marked, not less than 25mm PVC conduit with all accessories such as tee, bends, elbow, reducers, junction box etc fixed on wall/ceiling/truss and one run of PVC insulated unsheathed, multistranded copper conductor cable of 4.0 sqmm size, 1100 volts, ISI marked, FRLS grade green colour as earth continuty conductor connected to common earth dolly with and including modular box with cover plate frame in any module for single board having 3 x 5 Amps and 1 x 15 Amps switch socket on same board complete all as specified and directed by Engr in charge Note:Colour coding shall be folowed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Material and labour for concealed sub-main wiring with 2 runs of 4.0sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn through and including heavy grade stove enamelled steel conduit not less than 25mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 4.0 sqmm dia conduit insulated unsheathed copper conductor cable as earth dolly/mains, including taking up/down old unservucable sub main wiring and making good the distrubed surfaces as per existing complete all as specified and directed by Engr in charge . Note: i) Colour coding shall be as (i) Phase- Red/yellow/Blue (ii) Neutral - Black (iii) Earth - green ii) 2 runs of 4.0sqmm cable for phase,one run of 4.0 sqmm cable for earth and one run of stove enamelled conduit shall be measured and paid as one Mtr .

Supply and fixing Switch flame proof rotary type with termination box in LM6, 16A, single pole 250V complete all as specified and directed by Engr in charge

Supply and fixing Flame Proof switch socket & Plug combined in LM-6 cable termination box complete all as specified and directed by Engr in charge suitable for Gas Group of IIA & IIB and Zone 1 & 2

Supply and fixing flameproof mild steel sheet enclosure double door type for MCB DB SPN 8 way, 240 volts AC factory made, suitable for housing MCB SP along with 200 Amps copper bus bar complete all as specified and directed by Engr in charge suitable for Gas Group of IIA & IIB and Zone 1 & 2

Supply and fixing LED light fitting 2x16 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. Complete with all accessoriesprewired and including connecting up with three core flexible copper conductor cable with suitable complete all as specified and directed by Engr in charge

Supply and fixing flameproof exhaust fan 230V, AC, 600 mm sweep suitable for Gas Group of IIA & IIB and Zone 1 & 2 complete all as specified and directed by Engr in charge

Supply and fixing in repair new generation 20W LED batern (min 100 Lumen/watt) for surface and pendent application, anodized extruded aluminium housing, high transmissitvity diffuser high lumen output complete fixing arrangement complete all as specified and directed by Engr in charge

Supply and fixing in repair new generation Surface light LED 4 ft x 1 ft Luminaire 36 watt (min 100 Lumen/watt)for modern offices and CRCA powder coated body and high translucent diffuser provides high quality ecomonic energy saving lighting to modern offices complete all as specified and directed by Engr in charge

Supply and fixing in repair of double door type vertical type TPN DB 4 Way ,240V with 200A busbar , with metalic double door type IP 43 IK 09 protection suitable for housing MCCB's all as specified and directed by EIC. Note : DBs shall be concealed in wall where ever posible including making good the surface to match with surrounding complete all as specified and directed by Engr in charge

Supply and fixing MCCB FP 125 Amps,16KA, complete all as specified and directed by Engr in charge

Material and labour for concealed sub-main wiring with 2 runs of 2.50sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn through and including heavy grade PVC conduit not less than 25 mm dia (internal width) with all accessories like tees, elbows, junction boxs, reducer etc as required, including one run of 2.5 sqmm (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded copper conductor cable as earth dolly including taking up/down old unservucable sub main wiring and making good the distrubed surfaces as per existing complete all as specified and directed by Engr in charge . Note: (a) Colour coding shall be as (i) Phase- Red/yellow/Blue (ii) Neutral - Black (iii) Earth - green

Supply and fixing in replacement of LED highbay light 150 W energy saving and envirment friendly light fitting, pressure dia cost aluminium housing with aim & adjustable bracket, matt finished reflector for gglare elimination, SMD LED with secondary lens with IP 66 protection including all fixing accessories complete all as specified and directed

Supply and fixing single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 32 Amp complete etc all as specified and directed.

Supply and fixing GI cable tray perforated type 2 mm thick of size 450x50mm ( Including pre fabricated GI clamp suitable for fixing/supporting ) with0.71mm thick aluminium sheet cover, alloy 31000 H4 in ridges, Hips vally gutter cable trucking for plain to be fixed on any wall (brick/stone) vertically/horizontally including all accessories complete bending,shaping,drilling,welding, cutting & all fixing arrangement complete all as specified and directed by Engr in charge

Supply and fixing XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavyduty) with aluminium conductor, 1100 volts Earthed, grade cross sectional area 25 sq. mm 4 Core complete all as specified and directed by Engr in charge

Material and labour for sub-main wiring with 2 runs of 10.0sqmm copper conductor cable (FRLS grade), 1100 volts grade PVC insulated and unsheathed multi-stranded, drawn in and iincluding non metalic rigid PVC conduit not less than 25mm with all accessories fixed on wall//ceiling/truss etc as required, including one run of 10.0sqmm dia PVC insulated unsheathed copper conductor cable as earth dolly/mains, with all accessories like PVC elbow, PVC tee, etc including taking up/down old unserviceable sub main wiring and making good the distrubed surfaces/location complete all as specified and directed by Engr in charge . Note: (a) Colour coding shall be followed as (i) Phase- Red (ii) Neutral - Black (iii) Earth - green

Material and labour for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc as required 25x4mm galvanised iron strip as earthing lead complete all as specified and directed by Engr in charge

SHRI SAI ENTERPRISES

MADHU ENTERPRIZES