ADDN / ALTN AND IMPROVEMENT TO AUDITORIUM CUM LECTURE HALL (SAHYADRI AUDITORIUM) UNDER GE DEOLALI

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft and loose soil etc complete all as directed.

Excavating in post holes (or similar holes) in soft and loose soil each n exc 0.5 cu. m, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, etc complete all as directed.

M & L Plain Cement concrete type C2 1:3:6(40mm graded aggregate) in foundations,filling and mass concrete etc complete all as directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame exc 1.5 sq. m but n exc 4 sq. m each etc complete all as directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) n exc 1.5 sq. m each etc complete all as directed.

M&L for 1.25mm thick mild steel pressed steel frames of size 125x60mm for doors, double rebates including necessary fixing lugs 06 nos , 100mm size stainless steel hinges (03 nos for each shutter), lock, strike plate,filling the hollow portions of steel frame with PCC 1:3:6 type C-0 (12.5mm graded stone aggregate) etc complete all as specified & directed.

S&F 40mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including decorative veenered finish on both sides with lipping/frame to match etc complete all as specified & directed.

S&F powder coated (50 micron) anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified & directed

S & F powder coated of any colour (Thickness or powder coating not less than 50 micron).anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 No.). hinges type B-21 100mm long (2 No.) suitable handle (1No.) complete all as specified & directed

S&F 30 mm thick factory made solid panel PVC door shutter consisting of frame made out of M.S. tubes of 19mm x 19mm for stiles, & 15mm x 15mm for top & bottom rails. M.S. frame shall be covered with wood grain printed PVC sheet 5mm thick ‘C’ channel having a 5mm thick wood grain printed PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and 5mm thick wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side, and 10mm (5mm x 2) thick, 20mm wide cross wood grain printed PVC sheet as gap insert for top rail & bottom rail. Panelling of 5mm thick wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with PVC sheet beading, and joined together with solvent cement adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s instructions and drawing. The width of stiles & rails will be in proportion to the width of the door shutter as per SSR Clause No 8B.2.1 complete all as specified & directed.

M&L for Solid wood grain printed PVC door frame of the size 50 x 47mm made out of grain printed 5mm PVC sheet. The door profiles are to be reinforced with 19xl9mm M.S. Square tube. EPDM rubber gasket weather seal to be provided through out the frame. The profile shall be mitre cut at two corners and joined by inserting 2nos. of 150mm long brackets of 15x15mm M.S. square tube inside the 19mm x 19mm M.S. square tube and suitably screwed etc complete all as directed.

S&F 5.5 mm thick sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each fixed in window shutter etc complete all as directed.

S & F 4 mm thick figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each fixed in ventillators etc complete all as directed.

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and avg width of aperature 1.40 mm and fixed with stainless steel wire staples etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling of any description, size and thickness including cement mortor bedding (but not backing), removing rubbish off the premises etc complete all as specified and directed.

M & L for virified ceramic tiles, light shade 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar 1:6 set and jointed in neat cement slurry and pointed in coloured cement to match etc complete all as specified and directed.

All as per item No. 16 above but in vertical surfaces such as skirting and dado, laid over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M & L vitrified ceramic tiles dark shade/double charged 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15 mm thick screed bed in cement mortar 1:6 set and jointed in neat cement slurry and pointed in coloured cement to match etc complete all as specified and directed.

All as per item No. 18 above but in vertical surfaces such as skirting and dado, laid over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M & L for Non - skid, Glossy finish/Matt finish joint free coloured ceramic tiles 7 to 8 mm thick (square/rectangular) laid in floors area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. with and including 15mm thick screed bed in cement mortar 1:6 , set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete all as specified and directed.

M & L for glazed ceramic coloured joint free tiles in vertical surface 300X 450X 7mm thick with and including 10mm thick cement mortar 1:4 backing coat, set and jointed in neat cement slurry and pointed in white or colour cement to match etc complete all as specified and directed.

Dismantling of Stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortor etc complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate ) as in subase finished to receive floor treatment etc complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25mm thick in floors with and including 15mm thick cement mortar 1:6 cement screed bed, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing etc complete all as specified and directed.

All as per item no 24 above but pre-polished stones in skirtings 100mm high with and including 10mm thick cement mortar 1:4 backing coat complete all as specified and directed.

All as per item no 24 above but single piece pre-polished stones in treads and risers and including 15mm thick cement mortar 1:6 cement screed bed, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including mirror polishing etc complete all as specified and directed..

Demolition of plain cement concrete unreinforced in ground floor and paving n exc 15 cm thickness above or below GL etc complete all as directed.

BLANK

M&L for 50mm thick PCC M-15 (1:2:4) type B-1( 20mm graded stone aggregates) as in floors laid in alternative panels area n exc 7.00 sqm each with and inclusive of use and waste of formwork/steel channels of appropriate size to divide area in panels and finishing the same even and smooth broom finish without using extra cement etc complete all as specified and as directed.

Taking down existing chairs any description, fixed in any position etc complele all as specified and directed

Taking down existing curtains any description, fixed in any position etc complele all as specified and directed

Taking down existing screen any description, fixed in any position etc complele all as specified and directed

Dismantling wooden flooring, any description, fixed in any position with nails etc complete all as directed.

M&L for providing tiles made of wood fiber 1mm width cement composites 15 mm thick of size 600x600 / 600x1200 mm, with excellent noise absorption of 1 NRC as per ISO: 354-1985 and ASTM 423-90 a, Density 400 Kg/m3, meets stringent Fire Ratings ASTMD-876 and Fire Class -1 as per BS 476 part 5 and 6, Class P- not easily ignitable as per BS-476-Part 5 (Ignitability for material). This is applicable for core and class 1 as per BS 476-Part 7 (Method for classification of surface spread of flame), weather resistance as per IS 3308, Thermal Insulation as per IS: 3346-1980 with relative humidity of 90% RH at 60 degree Celsius(140 degree Fahrenheit) for 15 days= No deterioration. Conforms to En 131682001 and is RoHS Compliant. To be installed on T24 grid system of .6mm thick Main 'T'length minimum 3000mm, web minium 35mm to be placed at 600mm centre to centre and secondary cross 'T' of length 600mm web minium 35mm interlocked, wire support fot main T to be taken at every 1200mm lengthwise and 600mm widthwise specially designed for Acoustic vibration management and long life. 50mm thick, 1000 GSM absorb wool tested as per Fire retardant ASTMD 635-1991/Insulation and IS 15061-2002 for excellent results complete all as specified and directed. (Make; - APHONY FIBRETTE of M/s HIMALYAN ACOUSTIC or Equivalent of M/s BAUX or M/s HERA DESIGN ) Note: - 1. The quoted rate by the contractor shall be inclusive of cost of all the material mentioned here-in including necessary arrangement (screws etc) for its installation as per manufacturer's instruction at Stage Ceiling. 2. The color of the material shall be as approved by GE. 3. Test certificate of all the material to be submitted by the contractor to GE.

M&L for Providing 20/25mm Ceiling tiles made of Wood Fiber cement composites of size 1200 X 252 mm highly recommended for Ceilings with excellent noise absorption of 1 NRC as per ISO: 354-1985 and ASTM 423-90 a, Density 400 Kg/m , meets stringent Fire Ratings ASTMD-876 and Fire Class -1 and Class P-not easily ignitable as per BS-476-Part 5,6,7, weather resistance as per IS 3308, Thermal Insulation as per IS:3346-1980 with relative humidity of 90% RH at 60° Celsius (140° Fahrenheit) for 15 days= No deterioration. Tested as per En131682001 and are RoHS Compliant. To be installed on G.I studs 600x600mm center to center 2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life including 50mm thick, 1000 GSM absorb wool tested as per Fire Retardant ASTMD 635-1991/Insulation and IS15061-2002 for excellent results complete all as specified and directed. (Make; - FIBRETTE DOODLE of M/s HIMALYAN ACOUSTIC or Equivalent of M/s BAUX or M/s HERA DESIGN) Note: - 1. The quoted rate by the contractor shall be inclusive of cost of all the material mentioned here-in including necessary arrangement (screws etc) for its installation as per manufacturer's instruction at Hall Ceiling (except Stage). 2. The color of the material shall be as approved by GE. 3. Test certificate of all the material to be submitted by the contractor to GE.

M&L for providing Cement Fiber Tile of size 1200x300x5mm with square edge density 1050kg/m3 covered with absorptive microfiber coating on the front side and Acoustics fiber on the back side, thus making it acoustically absorptive, water resistance, fire resistant as per IS1734 of absorption coefficient0.89 at 160 Hz tested as per ISO 354. The tiles shall be anti-sag and are to be installed on G.I studs 600x600mm center to centre2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life, 50mm thick, 1000 GSM absorb wool tested as per Fire Retardant ASTMD 635-1991/Insulation and IS 15061-2002 for excellent results complete all as specified and directed. (Make; - M/s HIMALYAN ACOUSTIC or Equivalent of M/s BAUX & HERA DESIGN) Note: - 1. The quoted rate by the contractor shall be inclusive of cost of all the material mentioned here-in including necessary arrangement (screws etc) for its installation as per manufacturer's instruction at Hall Ceiling (except Stage). 2. The color of the material shall be as approved by GE. 3. Test certificate of all the material to be submitted by the contractor to GE.

M&L for providing FR Grades 2430x131x16mm made of exterior grade HDF backed with acoustical Fleece providing sound absorption of 0.6 NRC as per ISO 354.To be installed with 15mm Aluminium profile conforms to Aluminium Alloy 6063-T 6.Temper As per BS:1474-1987 and G.I Lock in clips on the back of tongue and Groove system. The density per panel shall be 750-800 kg/m3.The panels with tongue & groove for seamless patterns, 4-28mm Groove and visible panel. These slats shall be made from acoustical fiberboard with linear perforations for excellent uniformity. The perpendicular holes on the back of panel which shall be covered by black acoustical fleece to achieve sound reduction of 0.6 NRC. To be installed on ply strips directly on wall complete all as specified and directed. (Make; - WOODLOT of M/s HIMALYAN ACOUSTIC or Equivalent of M/s BAUX or M/s HERA DESIGN) Note: - 1.The quoted rate by the contractor shall be inclusive of cost of all the material mentioned here-in including necessary arrangement (screws etc) for its installation as per manufacturer's instruction at wall up to 8 ft height. 2. The color of the material shall be as approved by GE. 3. Test certificate of all the material to be submitted by the contractor to GE.

M&L for Providing Stretch Fabric System on G.I studs 2400mm X 50mm web, flanges 15 mm & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing 50mm thick insulation including wood fiber tile of size 600x1200x20mm with NRC 1.00 mechanically fastened on the G.I Studs. Acoustical infill of absorb wool 10mm to be adhered to the acoustical panel on the front side. 12mm/20mm Vinyl tracks screw fixed on to the 6mm ply and acoustics panels, the fabric is to be stretched over the Vinyl tracks. The installed system shall provide NRC of 1.00. To be installed on G.I studs 600x600mm center to center 2400mm X 50mm web thickness 0.5mm, flanges 15 mm & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life, 50mm thick, 1000 GSM absorb wool tested as per Fire Retardant ASTMD 635-1991/Insulation and IS 15061-2002 for excellent result complete all as specified and directed. (Make; - M/s HIMALYAN ACOUSTIC or Equivalent of M/s BAUX or M/s HERA DESIGN) Note: - 1. The quoted rate by the contractor shall be inclusive of cost of all the material mentioned here-in including necessary arrangement (screws etc) for its installation as per manufacturer's instruction on wall above 8 ft height. 2. The color of the material shall be as approved by GE. 3. Test certificate of all the material to be submitted by the contractor to GE.

M&L for providing 20/25mm tiles made of Wood Fiber cement composites of size 1200 X 252 mm with excellent noise absorption of 1 NRC as per ISO: 354-1985 and ASTM 423-90 a, Density 400Kg/m3 , meeting stringent Fire Ratings ASTMD-876 and Fire Class -1 and Class P-not easily ignitable as per BS-476-Part 5,6,7, weather resistance as per IS 3308,Thermal Insulation as per IS:3346-1980 with relative humidity of 90% RH at 60°Celsius (140° Fahrenheit) for 15 days= No deterioration. Tested as per En131682001 and are RoHS Compliant. To be installed on G.I studs 600x600mm center to centre 2400mm X 50mm web thickness 0.5mm, flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life, 50mm thick, 1000 GSM absorb wool tested as per Fire Retardant ASTMD 635-1991/Insulation and IS15061-2002 for excellent results complete all as specified and directed. (Make; - FIBRETTE DOODLE of M/s HIMALYAN ACOUSTIC or Equivalent of M/s BAUX or M/s HERA DESIGN) Note: - 1.The quoted rate by the contractor shall be inclusive of cost of all the material mentioned here-in including necessary arrangement (screws etc) for its installation as per manufacturer's instruction on wall above 8 ft height. 2. The color of the material shall be as approved by GE. 3. Test certificate of all the material to be submitted by the contractor to GE.

M&L for providing tiles 15 mm, taper edge made of compressed Wood Fiber made with inorganic compound with matt black color of size 600X1200/600X600mm with excellent noise absorption of 0.70 NRC as per ISO: 354-1985 and ASTM 423-90 a, STC of 48 as per ASTM 90/413 Density 650-750 Kg/m3, meets stringent Fire Ratings ASTM D- 876 and BS: 476, Tested as per ASTM C367-99. To be installed on G.I studs 600x600mm center to center 2400mm X 50mm web thickness 0.5mm, flanges 15 mm & 50 mm fully knurled giving it high strength, hot dipped galvanized steel with 120GSM zinc coating specially designed for Acoustic vibration management and long life. 50mm thick, 1000 GSM absorb wool tested as per Fire Retardant ASTMD 635-1991/Insulation and IS 15061-2002 for excellent results complete all as specified and directed. (Make; - APHONY FIBRIL of M/s HIMALYAN ACOUSTIC or Equivalent of M/s BAUX or M/s HERA DESIGN) Note: - 1. The quoted rate by the contractor shall be inclusive of cost of all the material mentioned here-in including necessary arrangement (screws etc) for its installation as per manufacturer's instruction on stage rear and side walls. 2. The color of the material shall be as approved by GE. 3. Test certificate of all the material to be submitted by the contractor to GE.

Blank

M&L for providing polished teak wood flooring with tongue and groove system of size 510x90x20mm on silent board of thickness 26 mm, mechanically screwed on 12mm ply, termite proof and seasoned. To be installed over Silent board 26mm 1218x1218 mm made of 20 mm compressed wood fiber cement composites 1250Kg/m3 with a backing of 6 mm Anti vibration Pad (30 STC for 16 mm as per ISO 354) thus giving an STC of 35. Note: - 1. The quoted rate by the contractor shall be inclusive of cost of all the material mentioned here-in and its installation as stage flooring. 2. The shade of polish on the flooring shall be as approved by GE. 3. Test certificate of all the material to be submitted by the contractor to GE.

M&L for providing Acoustic Door of 56 mm having an STC rating up to 50. The Door will be filled with high acoustic materials of 2 layers of 8 mm Water Proof Acoustic Ply with damper Sheet, 2 Layers of 10mm thick Absorb Wool 300 GSM, Sound damper 12mm of size 1218x1218 mm made of 10 mm compressed wood cement composites of density 1250Kg/m3 and 2 mm damper sheet having 37 STC as per ISO 140 (part III) - 1995. The door shall be finished with teak ply 4mm thick on interior and exterior side. The door frame shall be made of engineered wood. Frame on all four sides and drop seal below shall be provided along with the door. High load-bearing hinges shall be provided. The door shall be fire-resistant for 120 min as per IS 36 (Part 4 Part -II) & (Part 20 & 22) including door accessories :Door Closer, Door H-Type Pull Handle, Panic Bar & Outdoor Liver ( Trim Lock) complete all as specified and directed.

M&L for providing premium carpet having pile content of polyester fiber/olefin Frieze Heat Set Fiber, Pile Structure: Cut Pile, Backing: Action Back PP, Thickness: 14 mm, Pile Weight: 1500 GSM, Total Weight: 2000 GSM complete all as specified and directed. Note: - 1. The quoted rate by the contractor shall be inclusive of cost of all the material mentioned here-in and its installation as hall flooring. 2.The carpet pile content shall be as approved by GE.

S&F CNC Design Cutting 12mm thick HDHMR Board, high density and high moisture resistance premium board with back fixing of 40% light transmission white acrylic sheet. Hard wood used for higher density of product special glue being used to make it water resistant product as per indian climate water resistance characteristics as per ISI standard ideal suitable substrate with sharp cut & round edge, ready & smooth surface work complete including dismantling of existing board all as specified and directed (Stage front side) complele all as specified and directed. Make :- Green / Century / Actiontesa

Providing and Fixing of side skirting wooden beading work executed as per the instructions of Engineer-in-charge (EIC) including all tools, tackles, machineries, manpower, staging, any consumables, etc. complet Installation on side skirting & Molding 100mmX10/8mm as per requried finnishing with melamine polishing. Work complete etc complete all as specified and directed Make-As per Design - Specification complele all as specified and directed.

Providing and fixing of Horizontal MAIN CURTAIN The complete automatically motorized Stage curtain system with additional modified Gearbox fitted with sealed bearings self-lubricating centre split overlapped curtains both sides opening fully automatic Stage Curtain fixing steel rails track made out of 450 GSM made out of, double gathering Velvet, Molfin, Mokel or Hitech Fabric Curtain cloth drapery horizontal sliding arrangement complete with fixing rails, brackets and motorized operation complete with runners, master runners, pullies, 3mm steel wire rope, 1 HP Motor (Crompton or Godrej) 2 Nos Air Breaker Contactors (L&T/SIEMENS), 2nos. Micro Switches for auto stop, 3 nos push buttons for forward. All rollers are sliding with roller clamp, The curtain should be half of full width operated from control panel with control switches. Provision is for fully automatic operation only.Height 15ft , Length 37ft “Decorative fancy gota embroidered three layer golden border gota Patti on bottom of front Curtain” etc complete all as specified and directed FABRIC SPECIFICATION : 450 GSM VELVET, MOLFIN, HITECH & MOKENFabric Make : RAYMONDS, RELIANCE & TEXTILE PRO Make- Nexgen /Canara• Stage Works• illumitex Response 450 GSM/ stage work

Providing and fixing of Horizontal REAR CURTAIN: The complete fully automatically motorized Stage curtain system with additional modified Gearbox fitted with sealed bearings self-lubricating centre split overlapped curtains both sides opening fully automatic Stage Curtain fixing steel rails track made out of 450 GSM made out of, double gathering Velvet, Molfin, Mokel or Hitech Fabric Curtain cloth drapery horizontal sliding arrangement complete with fixing rails, brackets and motorized operation complete with runners, master runners, pullies, 3mm steel wire rope, 1 HP Motor (Crompton or Godrej) 2 Nos Air Breaker Contractors (L&T/SIEMENS), 2nos. Micro Switches for auto stop, 3 nos push buttons for forward. All rollers are sliding with roller clamp, The curtain should be half of full width operated from control panel with control switches.Height 15ft , Length 37ft etc complete all as specified and directed FABRIC SPECIFICATION : 450 GSM VELVET, MOLFIN, HITECH & MOKEN Fabric Make : RAYMONDS, RELIANCE & TEXTILE PRO Make- Nexgen /Canara• Stage Works• illumitex Response 450 GSM/ stage work

Providing & Fixing Frills (zalars) made of velvet/molfino of approved make, approved black colour and approved quality, stitched using 2 times width of cloth folded to form plates. The top edge of frill reinforced using Navar tape and stitching cotton ribbons at required distance on 28mm dia GI pipe etc. 4 No. frills - 37 feet (W) X 4 feet (H).Fabric : Velvet /Make : Nexgen /Response /450 GSM including taking down of existing frills.

Providing & fixing of Colored Non-Woven Pasting on 20mm Thick Acoustic Board with 50mm x 35mm x 0.5mm thk GI frame Stud, Intermediate & floor channel at 600mm x 600mm center to center & the center to be filled with 50mm thk polyester fiber insulation. The frame will be fix to the walls with necessary screws & fastners at 1200mm Center to Center.Make : Viraaj Extrutech or equivqlent as approved.

Providing and fixing of GRID STRUCTURE/Frame Work: Customized Fabrication of Main Overhead Grid or at various location of MS Iron complete all as specified and directed.Make: TATA/ Jindal

Supply and fixing of Hi-Gain Cyclorama projector cinema screen considering projector capacity of perforated HD mate fabric screen surface should be washable and including all necessary fittings etc. complete all as specified and directed. (Note : Necessary frame work for installation of screen will be paid separately) Make – Suvira / Draper / Stage Work/Prima/Liberty/Cinema

Providing and fixing Standard Heavy Duty Auditorium Chairs including all necessary fittings (Pushback, Auto Tip-Up Type) STRUCTURAL FRAME: BACK REST FRAME of ERW Tube / IS :3074-2005 GRADE 1-19 dia. Round Pipe 1.2 mm OR Mild Steel of size 25 X 3 mm flat bend as per ergonomic contour “ S “ bend to suit the body shape. SEAT FRAME: of ERW Tube / IS :3074-2005 GRADE 1-20 mm square Pipe 1.2 mm OR Mild Steel of size 20 X 5 mm flat “ C “ bend type.Note: In main load bearing structure no Wood based frame is permitted Leg: Sq. Tube IS: 4923-1997- 50 X 25 mm, 1.63 Thickness. SPRINGS: For Push Back mechanism Coil Spring / Spring Steel IS: 4454 1981 GRADE 2 Tested for 1,00,000 Cycles. Flexible PU FOAM: Automotive Grade High Resilience-HR Polyurethane foam of density: 48 ± 5 kg / M3. As per JIS K 6401 Thickness Cushion: 130 + 20 mm; Backrest: 80 + 10 mm Hardness: Cushion : 120 (+ 30 / - 20) Newton; Backrest : 80 (+ 30 / - 20) Newton FINISH: All Fasteners zinc passivity. All exposed & visible parts powder coated PUSHBACK CHAIRS SLIDING MECHANISM: Slider – 60 mm travels with self-lubricating non-breakable plastic made up of Virgin NYLON ball & main slider mechanism. The slider should withstand the load of a person sitting on the chair & it should be such that no dust or foreign particle can accommodate on it during the course of usage.

PLASTIC TRAY : The seat & back frame should be nicely cover with PPCP tray with 2 to 4 mm minimum wall thickness.It should comply to sound acoustic properties. ARM REST:PPCP with Cup holder OR PPCP without cup holder. AISLE LIGHTS DETAILS (can be provided on client request only): D.C. 12 VOLTS Operated LED Circuit. 1 LED current is 20 ma.(2 LED 40 ma) Parts Used: Diode ; 4 ( to convert a.c to d.c ) Resistor ; 2 ( for voltage controller ) L.E.D. ; 2 ( White Transparent 20 ma ) 5 mm PCB ; 1 ( Glass PCB ) Flexible wire ; 1 meter approx. Connecting ; 2 Clips ( Brass made ) Total load = 50 mamp (per circuit ) GROUTING: 4 Nos - M 8 X 75 mm expandable anchor fasteners. FABRIC: Heavy duty 100 % polyester dyed yarn with 3 mm ± 0.5 mm foam backing. Embroidery Logo /Print: As per Organisation Symbol. Fabric and colour shall be finally decided after approval of samples from AO. Basic dimension require are as follows: With ± 10 mm tolerance.Total height of the chair from the floor level = 980 to 1020 mm. Total height of the Seat from the floor level = 445 to 460 mm. Centre to centre of the chair = 535 mm. Depth of the sitting portion of the chair = 480 mm. Make : SPARK Pushback/Reciners/Cinema Works

Providing and fixing of non-recliner sofa one seater Complete wooden frame work single seater sofa complete wooden frame work of elegant design use of 12 mm 18mm ulternate ply seat material with frame use of 55 density cold moulded soft from of 5” for seat and back. Use of 40 density PU foam for the other body part with super soft foam lining sofa chair arm rest with 7-8” hand resting surface . Use of best quality double furniture Lethe rite material or soft suede best quality with letherite material Use four stainless steel legs. Sofa chair with ergonomically elegant design. Sofa chair total back height 44” and total length of the chair 35” or total width 35”. The recliner should come with one year warranty etc complete HSN Code 9403 Make : SPARK Pushback /Reciners/Cinema Works

Dismantling of wall and ceiling boarding any thickness,size any description,in any position, including all type of frame work fixed with screws etc complete all as directed.

Supply and fixing of sandwich insulated PUF roof panel Manufacture in continuous production line using pre painted Galvalume sheet 0.4mm thick sheet at top and bottom yield strength should be 550 MPa as per ASTM A-792 colour coating RMP (25 micron) RAL-9002 Panel thickness should be 40kg/m3 (+/- 2Kg/M3)HSN Code 73082019. Roof Pannel effective width should be 1000mm top and bottom PPGL sheet should protected with plastic film guard from scratch protection roof top should be 333mm with3 stiffing ribs at 1000mm crest height from bottom sheet should be 90 mm side lapping and over lapping joint will be vapour tight with guard film protection on all exposed surface and shall confirm to IS12346. Note : Work will be carried out through authorized applicator. Make TATA or Jindal

Dismantling of asbestos cement (corrugated, semi corrugated,etc ) sheets in roof coverings including ridges etc complete all as directed.

BLANK

S & F Pre-painted galvalume aluminum zinc coating GI based Corrugated steel sheet0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding towall, fixed with self tapping screws as specified and directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding towall, fixed with self tapping screws as specified and directed.

M&L for complete removal of existing treatment on surfaces of walls, removal of nails , including filling of cracks/holes by crack filler etc, preparing surface by one coat of 2mm thick putty and applying two coats lusture paint over one coat of primer complete all as specified and as directed. Make: Asian/Berger

All as per item no 59 above but two coats lusture paint on ceiling complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of walls and applying one coat of alkali resistant primer over a coat of 2mm thick birla white cement putty,sanding the surfaces till smooth finish is obtained and finally applying two coats of lusture paint etc complete all as directed.Make: Asian/Berger

All as per item No 61 above but two coats lusture paint on ceiling complete all as specified and as directed.Make: Asian/Berger

M&L for preparation of New decorated plastered or unplastered surfaces of walls/ceiling and applying two coats of weather emulsion white/red colour or as specified and directed by Engr-in-charge) by by roller/ brush over one coat of primer over 2mm thick Asian Wall Putty Suprema for levelling and smoothening, complete all as specified and directed.Make: Asian (apex suprema) / Berger (weather coat anti dust)

M&L for complete removal of existing treatment on surfaces of walls/ceiling, applying two coats of weather emulsion white/red colour or as specified and directed by Engr-in-charge) " over one coat of primer over 2mm thick Wall Putty for levelling and smoothening, including removal of unnecessary nails, filling of cracks/holes ,repair/crack filler mortar, including preparation of old decorated plastered or unplastered surfaces of walls/ceiling complete all as specified and directed.Make: Asian (apex suprema) / Berger (weather coat anti dust)

M&L for preparation of newly plastered surfaces of walls and applying one coat of alkali resistant primer over a coat of 3mm thick birla white cement putty,sanding the surfaces till smooth finish is obtained and finally applying two coats of oil emulsion distemper etc complete all as directed.Make: Asian/Berger/Nerolac

M&L for preparation of newly plastered surfaces of ceiling and applying one coat of alkali resistant primer over a coat of 3mm thick birla white cement putty,sanding the surfaces till smooth finish is obtained and finally applying two coats of oil emulsion distemper etc complete all as directed.Make: Asian/Berger/Nerolac

M&L for complete removal of existing treatment on surfaces of walls, removal of unnecessary nails with mechanical means/grinder, including filling of cracks/holes by crack filler etc, preparing surface by one coat of 3mm thick putty and applying two coats of oil emulsion distemper over one coat of primer complete all as specified and as directed.Make: Asian/Berger/Nerolac

M&L for complete removal of existing treatment on surfaces of ceiling , removal of unnecessary nails with mechanical means/grinder, including filling of cracks/holes by crack filler etc, preparing surface by and applying two coats of oil emulsion distemper complete all as specified and as directed. Make: Asian/Berger/Nerolac

Complete Removal of existing water proofing treatment any descrption,thickness and in any position including removal of rubbish of the premises etc complete all as directed by Engineer-in-charge.

M & L for water proofing treatment to RCC roof slab as specified below and as directed by Engineer-in-Charge :- (a) 15 mm th cement plaster in CM 1:4 with integral WPC to be laid over the RCC roof slab when the concrete is green to be finished even and smooth(without using extra cement) (b) Applying a uniform coat of bitumen primer @ 0.70 kg/sqm over cement plaster. (c) 3 mm th plain texture and weighing not less than 3.00 kg/sqm Atactic Polypropylene Polymer (APP) modified bitumen based prefabricated five layer water proofing membrane reinforced with non woven polyster (wt not less than 150 gms/ sqm) matt black finished over compatible primer at 0.4 Ltr / sqm of density at 25 degree centigrade 0.87 - 0.89 kg/ltr and viscosity 70-160 cps or cold sticker and torch application of membrane with overlap while torching shall be 150 mm on length side and 100 mm on width side. after necessary preparation of surface complete as per manufacturers instructions.

M&L for cement concrete type Bo 1:2:4 (using 12.5mm graded stone aggregate) 25mm thick as in roof to achieve slope on existing roof surface all as directed.

M&L for 20mm thick black granite (Table rubbed and polished) as in jambs, steps, pillars, window cills, platforms and the like in cement mortar 1:4 with and including 15mm bedding in CM 1:6 and pointing in white cement (1:2) using marble dust with admixture of pigment to match the colour of granite etc complete all as directed.

Extra over Granite or marble slabs as in rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations etc complete all as directed.

M&L for machine cut cudappah stone slab 20-25mm thick over and including 15mm thick CM 1:6 screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete etc complete all as directed.

M & L preparation of old treated steel surfaces of any description over 10cm in girth or width & applying one coats of synthetic enamel paint etc complete all as directed.

Taking down cement plaster on brick or stone walls built in cement mortor, etc , including raking out joints, hacking for key, scrubbing down with water, etc complete all as directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platforms and other similar situations etc complete all as specified and directed by Engineer-in-Charge.

M&L walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM (1:6) as in retaining walls, abutments and similar work etc as specified and direcetd.

Cutting holes in brick wall exc. half brick thick but not exc. one brick thick built in cement mortor for inserting holdfasts and making good dismantled portion in CM 1:3 or cement concrete 1:2:4 type B-1 as required exc. half brick but n.exc one brick etc complete all as directed.

S&F 100mm size butt hinges, cast brass, with stainless steel hinge pin, bright polished and fixed etc complete all as directed.

S&F in repair 150 mm long aluminum anodised, barrel tower bolts of extruded section etc complete all as directed.

S&F in repair 100 mm long aluminum anodised, barrel tower bolts of extruded section etc complete all as directed.

S&F in repair aluminum alloy anodised, sliding door bolts with hasp and staple, (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy and fixed 300mm long etc complete all as specified and directed.

S&F in repair 150 mm long extruded anodized aluminum alloy handles, fabricated type, etc complete and directed.

S&F in repair 100 mm long extruded anodized aluminum alloy handles, fabricated type, etc complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for and fixed in any position etc complete all as directed.

S & F mild steel of grade E-165 Fe-290 framed work such as decorative or intricate design window grills with ends of bars shouldered and/or riveted, or forged into spikes and similar work etc complete all as directed.

S&F 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber or steel frames as in cupboard shutters,shelves etc complete all as directed.

All as per item no 88 above above but 12mm thick as in shelves, kitchen cabinet shutters with and includive of 3mm thick teak wood lipping allaround

Taking up or down 15mm bore of pipe steel tubing and connections,including cleaning for refixing or removal from site by the contractor at his own expenses etc complete all as directed.

Taking up or down 20mm bore of pipe steel tubing and connections, including cleaning for refixing or removal from site by the contractor at his own expenses etc complete all as directed.

M&L for 15mm bore tubes, medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as directed.

All as per item No 92 above but refixing old 15 mm dia steel tubing and connections in new or old position (Walls, ceiling, floors, etc.)including supplying and fixing new fittings

M&L for 20mm bore tubes, medium grade galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors etc complete all as directed.

All as per item No 94 above but refixing 20 mm dia old steel tubing and connections in new or old position (Walls, ceiling, floors, etc.)including supplying and fixing new fittings

Dismantling water tanks exc 500 ltrs and not exc 1000 ltrs capaity and removing the same outside MD Land etc complete all as directed.

S&F 1000 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top ,double layer) hoisted and fixed in position all as specified in SSR Part I with and including 20mm bore of pipe ball brass valves, high pressure, with polythene float and flynut complete,screwed for iron pipe or brass ferrule and fixed etc complete all as directed.

BLANK

S&F in repairs 15mm size fancy type Pillar taps with 200mm extension body, brass chromium plated, screwed down both ends for iron pipe or for union and fixed etc complete all as specified and directed. (Make- Jaquar Model No.- FUS-CHR-29021 OR EQUIVALENT

S&F in repairs 15 mm size fancy type Bib taps with wall flange, brass chromium plated screwed down both ends for iron pipe or for union and fixed etc complete all as specified and directed. (Make- Jaquar Model No.-FUS-CHR-29037 OR eqivalent

BLANK

BLANK

S&F in repairs 15 mm size fancy type exposed part kit of concealed stop cock with fitting sleeve,operating lever & adjustable wall flange brass chromium plated screwed down both ends for iron pipe or for union and fixed etc complete all as specified and directed. (Make- Jaquar Model No.-CON-CHR-083FTK OR eqivalent

S&F in repairs 15 mm size fancy type regular body of concealed stop cock suitable for 15mm pipe line with plastic protection cap (without exposed parts) brass chromium plated screwed down both ends for iron pipe or for union and fixed etc complete all as specified and directed. (Make- Jaquar Model No.-ALD-CHR-083FT OR eqivalent

S&F in repairs 15mm size fancy type chromum plated angular Stop valves with wall flange screwed both ends for iron pipe or for unions and fixed etc complete all as directed. Make -jaquar model No.-FUS-CHR-29053 or equivalent

S&F in repairs 32mm bore waste fittings, brass chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed etc complete all as directed.

S & F in repairs gratings round 140 mm size of PTMT (minimum weight 50gms) etc complete all as directed.

S&F in repairs PVC connections 15mm size with PTMT nuts of length 450mm etc complete all as directed.

S&F in repairs 75mm bore of pipe PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls etc complete all as directed.

All as per item no 109 above but 110mm dia.

S&F in repairs 32mm bore of pipe low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc complete all as directed.

S&F in repairs 40 mm bore of pipe low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors etc complete all as directed.

S&F in repairs 75mm bore of pipe PVC (SWR) bends any radius with access door etc complete all as directed.

All as per item no 113 above but 110mm dia

S&F in repairs Cast iron nahani trap with diameter of outlet 75mm with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

BLANK

S & F including fixed in repair vitreous china white under counter wash hand basin of size 595x420x200mm oval shaped of continental series fixed in granite counter top etc complete all as specified and directed. (Make- Jaquar Model No.-CNS-EHT-705 OR EQUIVALENT

S & F in repair vitreous china wash down water closet pan (pdedestal pattern )in single piece i.e. WC and UF seat cover ,hinges,fixing assessory set ,cistern & fitting size 655x365x765 mm, P trap 180mm and fixed complete all as specified and directed. Make- Jaquar model No LYS-WHT-38851P180UFSM or equivalent

S& F in repair Vitreous China squatting pan, ‘Orissa’ pattern, size 580 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and directed.

S & F in repair wall hung cistern with 39mm drainage L-bend pipe with gasket &installation kit(suitable for EWC) complete all as specified and directed. Make- Jaquar model No WHC-WHT-184L or equivalent

S & F in repairs vitreous china wall mounted sensor urinal of size 480x300x740mm with fixing accessories set with sensor flushing valve with complete kit (Battery operated) complete all as specified and directed. Make- Jaquar model No URS-WHT-13255 & SNR-CHR-51097 or equivalent.

S & F in repair overhead shower 140mm dia round shape single flow with air effect (ABS body and face plate chrome plated )with rubit cleaning system etc complete all as directed. Make- Jaquar model No OHS-CHR-1757 or equivalent

S&F in repairs brass chromium plated fancy type health faucet with 8mm dia 1.2 m long flexible tube and wall hook etc complete all as directed. Make -Jaquar model No.-ALD-CHR-573 OR EQUIVALENT

S & F in repair fancy type brass chromium plated toilet paper holder with flap of make ' Jaquar ' collection . Model No . ACN-CHR-1153S or equivalent

S&F in repairs single towel rail, 600 MM long etc complete all as specified and directed.make ' Jaquar ' Model No .ACN-CHR-1111NM or equivalent

S&F in repairs 20mm dia stainless steel curtain rails heavy grade fixed in brackets etc complete all as specified

M&L for applying sockets for injection grouting including drilling holes in concrete of slab,fixing perforated sockets of approx 150mm length,cleaning the holes,placing sockets at predefined angles and prepacking the same with packing putty,grouting with neat cement sluury under pressure including adding Cebex 100 expandable grouting admixture to fill the sockets/port completly and proceeding in methodical manner for all sockets fixed till the grout is filled and returns from the holes,cutting off the extra length of socket, plugging the holes,cleaning etc complete all as directed.

M&L for special treatment to sunken portions of Toilet by demolition of existing treatment of any description and thickness,removal rubbish outside MD land, 10mm thick plaster in cement mortar (1:4) with water proofing liquid conplast 421 of make Fosroc or equivalent as specified and applying one coat of each Nittoproof 100 and Nittoproof 120 of M/S Fosroc or equivalent as specified on plastered surface and rendering again 10mm plaster in cement moratr (1;4) mixed with conplast 421 of M/S Fosroc or equivalent as specified in Sunken portion and CI pipe joints shall be filled/jointed with mixture of cement, fine, sand and Nittoproof 130 of M/S Fosroc or equivalent as specified and provide hole in the wall and fix 600mm long and 20mm dia GI spouts light grade and PCC (1:5:10) type E-2 using 40mm graded stone aggregate filling in sunken portions , floor area of WC& Bath upto 5.50 Sqm complete all as specified and directed.

M&L for mild steel work tubular pipes as in stanchions incl special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 etc complete all as directed.

M & L for preparation of new steel surfaces exc 10 cm width/girth and applying two coats of synthethic enamel paint over a coat of primer etc complete all as directed.

M & L for 10 mm thick rendering in cement mortar 1:6 on brick/ concrete surfaces and finishing the surfaces even and smooth (without using extra cement) with a thin layer of sagol finish etc complete all as specified and as directed by the EIC.

M&L for 15 mm thick rendering in cement mortar 1:4 on brick/concrete external surfaces of walls mixed with water proofing compound 2% by weight of cement sand faced sponge faced finish etc complete all as specified and directed. Note- WPC shall be measured and paid separately.

Supply only integral water proofing compound of approved make all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B1(20mm graded stone aggregate) nominal mix as in beams, seimic bands, cantilevers, bressumers and lintels etc, basement slabs, under-reamed piles and mass concrete etc complete all as directed.

M&L for reinforced cement concrete 1:2:4 type B1(20mm graded stone aggregate) nominal mix as in Slabs supported on walls, beams and columns in floors,roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as directed.

M&L for formwork to sides and soffits of floor or roof beams, beams haunchings, girders, bressumers,lintels, cantilevers, shelves including supports overhangs etc also splays between floors and beams etc flat rough finished surfaces of concrete etc complete all as directed.

M & L for Fe 500 TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire(annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and as directed.

M&L for Fe 500 TMT bars 6mm to 8mmdia cut to length ,bent to shape rquired including cranking, bending spirally for hooping for columns & binding with and including mild steel wire (annealed )not less than 0.9 mm dia in reinforcement for man holes cover slabs etc complete all as specified and as directed.

S&F plain plates grade Fe-410-W, square cut or notched including forming holes ordinary and counter sunk

S&F 12mm mild steel rag or lewised bolts, screwed one end, the other end enlarged and jagged or lewised exc 30cm long etc complete all as directed.

S&F mild steel screw bolts machine made 5 to 10mm dia with hexagonal or square heads at one end and screwed the other or screwed both ends each screwed end fitted with one washers and hexagonal or square nut n exc 5cm long etc complete all as directed.

M&L for PCC 1:3:6 type C2 using 40 mm graded agg as in plinth protection 75 mm thickness, finished even and smooth without using extra cement with and including 10mm wide and 30mm deep joints at every 2.4mtrs interval and at every change in direction filled with bitumastic compound etc complete all as specified and direted.

Demolition of Brick work or stone/boulder masonry walls including all quoins arches pillares etc in any position and built in cement mortor etc complete all as specified and directed.

M&L for fly ash brick work with modular size bricks straight or curved on plan exc. 6m mean radius and built in CM 1:6 etc complete all as directed.

All as per item no. 145 above but half brick thick walls built in CM 1:4 complete all as directed.

S&F 20mm thick black granite slabs of premium quality as in partitions for urinals with and including cutting chases in stone masonry walls for the required insertions and full round nosing to exposed lenghts jointed and ponted in neat coloured cement paste to match the shade of slab etc complete all as specified and as directed.

Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding,buffing, polishing and making curvature (where ever required) and fitting the same with necessarystainless steel nuts and bolts complete, includingstainless steel nuts and bolts complete, includingfixing the railing with necessary accessories &stainless steel dash fasteners, stainless steel boltsetc., of required size, on the top of floor orthe side of waist slab with suitable arrangement etc complete all as specified and as directed.

BLANK

M & L for 10mm Toughned glass as in hinged doors, partitions automatic doors and similar work including cutting to shape,drilling holes etc complete all as specified and as directed.

S&F plain solid straight for battens of 2nd class hard wood wrought framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed all as specified and directed.

BLANK

BLANK

Taking down carefully unserviceable copper/aluminium point wiring of any description including all fittings (switch , socket, switch socket combination, lamp holder, ceiling rose, regulator etc.) and making good disturbed surfaces of wall, floor etc. to match with existing finishes complete all as specified and as directed.

M&L Point wiring with two single core, 1.5 sqmm (nominal area) size multistranded copper conductor cable and one single core 1.5 sqmm size copper conductor cable as earth continuity conductor connected to common earth dolly,1100 volts grade , FRLS, PVC insulated unsheathed cable in and including PVC rigid conduit of suitable size, duly concealed in wall, floor, ceiling etc, including provision of mild steel modular type terminal boxes of suitable module made with mild steel sheet duly galvanised and suitable for fixing modular type switches / sockets / regulators / AC starters etc. fixed in recess of wall with brass chromium plated screws and cap washer complete for the following:-

One light point controlled by one switch

BLANK

One 5 pin, 6 A socket outlet on the same board

One 5 pin, 6 A socket outlet on the independent board.

One bell point controlled by one switch.

All as per item No 155 here-in-before but with two 2.5 sqmm size cables as phase and neutral and one 2.5 sqmm size cable as earth continuity conductor for one 15 Amps socket outlet independent

Material and labour for point wiring with stranded copper conductor PVC insulated unsheathed 1.5 Sqmm FRLS cable in and including PVC casing caping of suitable size including provision of PVC modular type terminal boxes of suitable module made with PVC sheet and suitable for fixing modular type switches, Cover plate of appropriate sizes and all requisite accessories such as PVC elbow,Tee,collers bend with one single core continuous 1.5 Sqmm,FRLS copper cable for earth wire complete all as specified and as directed for :-

One light point controlled by one switch.

One light point controlled by two two way switches.

BLANK

One 5 pin socket outlet 5 Amps on the same board.

One 5 pin socket outlet. 5 Amps on the independent. board

All as per item No- 157 above but One 15 A socket outlet independent with 2.5 sq mm PVC cable and 1.5 sqmm cable as earth continuity wire.

All as per item No 157 here-in-before but with two 4 sqmm size cables as phase and neutral and one 4 sqmm size cable as earth continuity conductor for one Plug & Socket DB independent

S&F Plug & Socket DB, CRCA Sheet steel, powder coated, with metal plug & socket 3 pin with 20 Amps MCB SP 240 Volts complete as specified and directed Make : L&T (Cat No: DBMPPS332SD)

Supply and fix following accessories all as specified and directed:-

Ceiling rose, 3 terminal, PVC / Polycarbonate insulated body

Modular type switch, 1 way, 6 Amps, 1 module

Modular type socket, 2 & 3 pin combined, 06 Amps, 2 module

Modular type switch, 1 way, 16 Amps, 1 module

Modular type socket, 3 pin, 06 Amps / 16 Amps combined, 2 module

Modular type bell push switch, 1 way,6 Amps, 1 module

Call Bell, ding dong type suitable for 230 / 240 volts AC 50 Hz supply

BLANK

Modular type TV socket, 2 module, white colour complete.

Cover plate with frame suitable for 2 Module

Cover plate with frame suitable for 3 Module

Cover plate with frame suitable for 4 Module

Cover plate with frame suitable for 6 Module

Cover plate with frame suitable for 8 Module

Cover plate with frame suitable for 12 Module

Cover plate with frame suitable for 18 Module

Taking down old unserviceable light fitting of any type from existing area and making good surface foe new fittings all as specified and directed

Supply and fixing LED tube lights fitting, 4 feet long 1x 18W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

S&F Decorative wall light fixture with Champagne gold finish fixture with plastic body with 10 Watt LED lamp all as specified and as directed . Make: Havells (Cat No:LHFOECE1TZ1O014) or equivalent in Crompton Greaves / Bajaj

Supply and fixing LED luminaire 600 mm x 600 mm, 40 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete.

Supply and fix LED 3 watts Step light powder coated die cast aluminium housing in IP 65 pretection all as specified.

S&F Industrial LED Luminaries energy saving environment friendly & robusty highbay LED IP 65 lumilire 100 Watt all as specified and directed. Make Havells- SAUCERNEOP100WLED75790DLTG or equivalent in Bajaj/CG

S&F recess mounted round shaped powder coated body 20 Watt LED with driver Watt Wall washers, tiltted 70 degree and swives 360 degree offer best illumination on wall and retail displays Make : Havells Cat No SPARKLEPROSNOOTDLR20WLED840MOD38D or equivalent in Bajaj/CG

Supply and fixing building LED security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Taking down of any type of DBs along with MCBs etc from existing place and making good surface of new DBs ibstallatin all as specified

S&F Powerline Vertical TPN DB with suitable for 160A MCCB incomer, double door (IP-54), 8 Ways, built- in 250 Amps copper busbar for each phase complete suitable for 415 Volts, AC, 50 Hz complete all as specified and as directed Make : Legrand (Cat No: 507752)

S&F Thermal Magnetic relese MCCBs, 4 pole, 415 volts, breaking capacity 25 KA, rating 160 Amps, complete all as specified and as directed. Make: Legrand- Cat no 17498 /C&S/L&T

S&F MCBs, Triple pole, 415 volts, breaking capacity 10 KA, rating 63 amps, complete all as specified and as directed. Make: L&T / Legrand /C&S/Havells

S&F Sheet Metal enclosure for SPN DBs, 8 Ways, Double Door built in 200 Amps bus bar (IP-43), built- in bus bars complete suitable for 240 Volts, AC, 50 Hz complete all as specified and as directed Make: L&T / Legrand /C&S/Havells

S&F Sheet Metal enclosure for SPN DBs, 12 Ways, Double Door, built in 200 Amps bus bar complete suitable for 240 Volts, AC, 50 Hz complete all as specified and as directed Make: L&T / Legrand /C&S/Havells

S&F MCBs, SPN, 240 volts, breaking capacity 10 KA, rating 40-63 amps, complete all as specified and as directed. Make: L&T / Legrand /C&S/Havells

S&F MCB, SP,240 volts, breaking capacity 10 KA, rating 40 to 63 amps, complete all as specified and as directed. Make: L&T / Legrand /C&S/Havells

S&F MCB, SP,240 volts, breaking capacity 10 KA, rating 6 to 32 amps, complete all as specified and as directed. Make: L&T / Legrand /C&S/Havells

Taking down of any type of Sub main wiring in Existing area and making good surface for new wiring all as specified and directed

M&L submain wiring with two single core PVC insulated, unsheathed, stranded copper conductor cable (FRLS), 1100 volts grade of size 6 Sqmm (nominal area) each and one single core 6.0 Sqmm (nominal area) as earth continuity conductor drawn into PVC casing capping complete all as specified and directed. NOTE: (i) Rates for PVC casing capping with accessories are deemed to be included in the unit rate.

All as per item No - 181 above but with 2 runs of 4 Sqmm cable with one run of 4 Sqmm cable for earthing.

Supply and fixing Rigid non metalic PVC Conduit/ PVC Casing and Caping 25 mm dia including all tees Bends elbows and fixing ii wall with screws and saddles for rthrowing net cable/ Speaker cable/ computer cable etc all as specified and directed

M&L for wiring in PVC Casing and caping with two single core PVC FRLS copper cable size of 1.5 sq mm and 1.5 sq mm earth wire suitable sound system all as specified and directed.

BLANK

BLANK

BLANK

BLANK

Supply & fix single pointed air termination aluminium rod 12mm dia and 300 mm long incl support block incl taking down u/s complete all as speicified.

Supply and installation of earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawin in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc as required 32x6mm GI strip incl taking down old strip any type complete

Supply & fix aluminium strip 25mmx 3mm as a roof conductor or down conductor complete all with saddles and fixing screws for fitting the strip incl taking down any type strip complete all as specified and directed by Engr-in-charge at site.

M&L for HDPE/porceiline insulator suitable for fixing earthing strip to the wall / floor/pole or any indicated location etc all as specified and as directed

Supply and fixing test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm , drilled and screwed including 3 nos. 8mm dia 25 mm long hex. head screw, complete with suitable polycaronate box with locking arrangement all as specified and directed by Engr-in-charge.

M&L Earthing with galvanized steel plate electrode 600 mm x 600 mm x 6 mm thick, burried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to galvanized iron strip 32 x 6 mm size by means of GI bolts, nuts, check nuts and washers, earth strip protected by galvanized steel pipe 40 mm bore (light grade) connected to main switch board or any other electrical equipment all as shown in electrical plate No. 3 of SSR-2010 Part I and including necessary excavation and earth work in any type of soil, 20 mm bore medium grade GI pipe for watering, funnel with wire mesh, PCC (1:3:6), type C-1 chamber, RCC (1:2:4), type B-1, reinforced with 6 mm dia MS round bars @ 15 cm c/c both way for cover and MS frame etc., complete all as specified.

M&L Earthing with galvanized mild steel earth plate electrode size 600x600x6mm thick buried directly in ground (Preferably in vertical position) earth pit not less than 2.25 meter below normal ground level with top edge of the earth plate not less 1.5 meter (BGL) connected to galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nut and washer of galvanized iron including PCC pit in RCC 1:2:4 type B-1, precast RCC cover with suitable handle, excavation and earth work in any type of soil, 20mm bore “medium grade” galvanized iron water tubing fixed with cast iron funnel and wire mesh and 15mm bore “light grade” galvanized iron protection pipe for earth lead wire upto 5m length, charcoal, common salt, complete all as shown in EP No 3 of SSR 2020 part-I, connected to test point complete, all as specified and testing on completion.

Material and labour for cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty 1100 Volts grade with stranded aluminium conductor of size 240 Sqmm 3.5 Core, including glands, lugs, nut, bolts, washers as required at site, testing complete all as specified and directed.

Material and labour for cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty 1100 Volts grade with stranded aluminium conductor of size70 Sqmm 3.5 Core, including glands, lugs, nut, bolts, washers as required at site, testing complete all as specified and directed.

Material and labour for cable XLPE insulated screened PVC bedded, galvanised steel strip or wire armored, electric power cables (heavy duty 1100 Volts grade with stranded aluminium conductor of size 35 Sqmm 3.5 Core, including glands, lugs, nut, bolts, washers as required at site, testing complete all as specified and directed.

Excavation in trenches not exceeding 1.5 metres wide and not exceeding1.5 metres in depth and getting out in soft/ loose soil complete all as specified.

Returning, filling in, including spreading , leveling , watering and well ramming in layer not exceeding 25cm each layer all as specified.

Removing excavated material not exceeding 50M and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified.

Material and labour for Sand cushioning to underground cables provided with a layer of sand 8cm thick before laying the cable in trenches and 15cm thick after laying the cable in trenches complete all as specified.

Material and labour for Relaying of B bricks for covering to cable laid dry flat ,with width equal to the length of brick.

M&L Sub class ‘B’bricks for covering to cable laid dry flat ,with width equal to the length of brick.

S & F Steel pipe glavanized light grade of 40 mm dia laid in trenches or under ground/floor or road of fixed with pole for protection of cable/ Earth sstrip including clams with bolts nuts and wasers complete ass as specifed.

S & F Steel pipe glavanized light grade of 80 mm dia laid in trenches or under ground/floor or road of fixed with pole for protection of cable/ Earth sstrip including clams with bolts nuts and wasers complete ass as specifed.

M & L for Boring of holes under road, pavement, hard standing by trenchless technology for laying of GI Pipe for LT cable by using necessary machinery including laying of Heavy duty GI pipe of 80 mm dia all as specified and as directed by Engr-in-Charge

Dismantling of unserviceable LT panel of any type and Supply, fabricate, erect, connect, test and commissioning of factory made, CPRI approved, cubical type, Indoor type LT panel board, totally enclosed, dust, weather and vermin proof 1100 Volt grade, 50 HZ supply made out by 3.00mm thick CRCA sheet for load bearing and 2mm thick for non load bearing, fully compartmentalised, with IP - 55 protection, painted with powder coated paint, angle iron padastal frame 600mm hight above ground level all as per conforming to IS-2417 of 1962, including taking down old Panel, complete including the following accessories for each set all as specified and directed. (Loc- Sahyadri pic hall)

(a) 4 Nos bus bar of equal size made out of copper strip of suitable size with PVC insulated coloured heat shrinkable type sleeves, of rating 650 Amps, for looping and branch connection system, mounted on non cracking resin type insulators - 01 Job. (b) TPN, 4 Pole, MCCB (electronic based 400 Amps, 415 Volt, 50 KA - 01 No. (Incomming) (c) TPN, 4 Pole, MCCB ( thermal magnetic release) 200 Amps, 415 Volt, 25KA - 03No. (Outgoing) (d) TPN, 4 Pole, nload change over switch front operated400 Amps, 415 Volt- 01No. (e) TPN, 4 Pole, MCB ( thermal magnetic release) 63 Amps, 415 Volt, 25KA - 02No. (Outgoing) (f) TPN, MCB 63 Amps, 415 Volt, 10KA - 03No. (Outgoing) (g) SPN, MCB 63 Amps, - 02No. (Outgoing) (h) SPN, MCB 32 Amps, - 02No. (Outgoing) (i) Indication lamps R, Y & B - 01 Set (j) Provisioning of copper tinned cable glands for incoming and outgoing cables - 01 Job. (k) Provision of multi functional meter. with CTs and PTs (Volt, amp, hz)-01 set (Note- MCCBs and acessories make -Legrand/ L&T/Schnider)

: Supply and install vertical pack type (Tower AC Unit) air condition unit capacity of 4 TR 3 Phase 415 volt, 50 Hz indoor and outdoor complete with cordless remote control unit twin rotary compressor scroll type, cooling capacity 4800 Btu/Hr and indoor noice level less than 51 dB (A) and regrigerant type R22 including inter connection of copper pipe between indoor and outdoor unit, mounting arrangement of outdoor unit in wall and necessary electric connection upto DBs all as specified and directed. Make : Blue Star/Samsung/Carrier/Mistubishi

S&F Powerline Vertical TPN DB with suitable for 160A MCCB incomer, double door (IP-54), 8 Ways, built- in 250 Amps copper busbar for each phase complete suitable for 415 Volts, AC, 50 Hz complete all as specified and as directed Make : Legrand (Cat No: 507752)

S&F Thermal Magnetic relese MCCBs, 4 pole, 415 volts, breaking capacity 25 KA, rating 160 Amps, complete all as specified and as directed. Make: Legrand- Cat no 17498 /C&S/L&T

S&F MCBs, Triple pole, 415 volts, breaking capacity 10 KA, rating 63 amps, complete all as specified and as directed. Make: L&T / Legrand /C&S/Havells

S&F Plug & Socket DB, CRCA Sheet steel, powder coated, with metal plug & socket 3 pin with 20 Amps MCB SPN complete as specified and directed Make : L&T (Cat No: DBMPPS220SD)

S&F Plug & Socket DB, CRCA Sheet steel, powder coated, with metal plug & socket Triple pole and Earth enclosure with three pin and earth plug with socket including 32 Amps MCB TPN complete as specified and directed Make : L&T (Cat No: DBMPPS332SD)

M&L submain wiring with Four single core PVC insulated, unsheathed, stranded copper conductor cable (FRLS), 1100 volts grade of size 10 Sqmm (nominal area) each and two single core 10.0 Sqmm (nominal area) as earth continuity conductor drawn into PVC conduit complete all as specified and directed. NOTE: (i) Rates for PVC conduit with accessories are deemed to be included in the unit rate.

M&L submain wiring with four single core PVC insulated, unsheathed, stranded copper conductor cable (FRLS), 1100 volts grade of size 6 Sqmm (nominal area) each and one single core 6.0 Sqmm (nominal area) as earth continuity conductor drawn into PVC casing capping complete all as specified and directed. NOTE: (i) Rates for PVC casing capping with accessories are deemed to be included in the unit rate.

Supply, erecting, testing and commissioning complete of manufacturer or OEM manufactured static, silent (Sound Proof enclosure) Diesel Engine Driven Generating Set capable of delivering 160 KVA at power factor 0.8. water coolled, 415 Volts (AC three phase, 4 wire system of supply) 50 Hz. The DG Set shall consists of diesel engine coupled to a matching alternator, through flexible coupling and mounted on common base frame and complete with control panel standardized by manufacturer, fuel tank with mounting arrangements and inlet, outlet, return inlet oil arrangement exhaust pipe complete and suitable for conditions prevalent at devlali (Capacity of Engine, alternators shall be worked out taking all derating factors into consideration) including PCC foundation (of suitable size leaving at least 0.5 M all around for ease up movment and 0.5M height above NGL) anti-vibration pads, including all features to comply with latest CPCB guidelines .and comprising of followings:- Make: Kirloskar / Cummins India/Greaves –Cotton,

(i) Engine (Prime Mover):- Diesel Engine 1500 RPM, Direct injection multi Cylinders, four stroke, confirming to ISO 3046/BS 5514, water cooled, naturally turbo charged, capable of giving adequate BHP to drive Alternator capable of delivering 160 KVA at outdoor atmospheric conditions at Devlali, (Taking all derating factor into consideration), 12 Volt (as per manufacturer recommendations) electrical battery start, complete with fly wheel with all standerd fittings/fixtures as per manufacturer and including suitable panel for tachometer, lub oil temperature, pressure gauge and frequency meters and also including self starter system, dynamo, fuel electric control panel with electronic governor (ECPG) and Engine protection system (Shut down, indication for High water temperature, low lub oil, oil pressure, over speed etc.), multi functional meter for RPM, PF,hrs runs,frequency, oil pressure,temp,amps and voltage indications, fuel tank and first fill of lub oil, coolant and other consumables etc. (ii) ALTERNATOR:- Brushless AC alternator, 3 Phase, 415 Volt, 4 wire, rated for output of 160 KVA, at power factor 0.8, 1500 RPM, IP 23 class enclosure, insulation Class "H", salient pole, revolving field, single bearing automatic voltage regulator coupled through flexible coupling with and to match the above engine.

(iii) BASE PLATE :- made out of structural steel as per manufacturers recommended design/specifications. . (iv) ACOUSTIC ENCLOSURE: Sheet metal fabricated cope type silent enclosure manufactured on CNC machines as per CPCB norms and powder coated after seven tank process, the enclosure shall be designed for reducing the sound level to 75 DB (A) at a distance of 1 M at 75 % load under field condition and ox 70DB at 3 M from Gen set when DG set is working at full load along with testing conformance, labeling certification etc as laid down in GSR No.371(E) dt 17 May 2002. (v) Foundation/Plinth/Base : shall be provided as per manufacturers recommendation, however minimum 0.5 m space should be available all around the set and height of plinth shall not be less than 0.5 M (vi) Diesel storage tank of capacity adequate for storage of diesel for 12 hours operation of Gen set. (vii) MISC : Tool kit, Operation and maintenance catalogue, spare part list overhauling manuals guarantee card etc shall be provided as per manufacturer standard pratices.

NOTES:-(i) The capacity of Generator set shall be net after all due derating factors as per relevant ISI design. (ii) Rate quoted shall be deemed to be inclusive of cable and terminations form Generator all as specified and directed. (iii) The quoted rate shall be deemed to be inclusive of first fill of oil and final successful acceptance test. (iv) The quoted rate shall be deemed to be inclusive of 12 hours test run at site including of half an hour on 10% overhead in presence of representative detailed by accepting Officer, all arrangements including consumables like diesel, oil, coolant, load for testing etc are to be made by the contractor for the tests.

Supply, installation & testing of AMF Panel comprisin AST kit. of size 1.5mx1.2mx.05m made out of 3.00 mm thick CRCA sheet, copper bus bar of suitable size, internaly pre wired , panel shall be totally enclosed dust, weather & vermin proof, with powder coated after washed with RR- 10 chemical for rust proofing, mounted on 50x50x6 mm angle Iron stand floor mounted &cosisting of following accessories:-

a) Automatic Source Transfer System (ASTS DN2-250A ) 250 Amps. Make L&T Model No DN2 250. -01 set ( Complete with connecting bus-bar assembly , Cable harness, 2 MCCBs 250A(DN2) + 2 SE-EOM + 2 ATAC + 1 MIL kit ) b) Automatic Transfer Controllers (ATC) (AuXC-2000) with cable harness make-L&T, cat part No ATC2000OOOO - one No c) Control MCB SP 6 Amp. 230 V – 6 Nos. d) LED Indicating Light for Main & DG R-Y-B power supply — 6 Nos. e) LED Indicating Light for Main & Gen. ON – 2 Nos. f) Battery Charger (inbuilt) with LED Indicating Light for battery Charger –1 No. g) Multi functional meter for Volt, Amps, PF, Frequency, make L&T, Model- WL440510OOOO h) MCCB 250 Amps 4 pole 36 KA (CM92106OOP1OG) . Make L&T with spreader link- 02 Nos I) CT Coil of suitable ratio ---- 6 Nos. j) Engine start relay k) Connector block for control wiring. l) Auto / Manual Switch ---1 No. m) Start & Stop Push Button with cable harness--1 Set n) Copper bus- bar of capacity 400 A 0) All other minor accessories required for AMF panel.

Supply, fabricate, erect, connect, test and commissioning of factory made, CPRI approved, cubical type, Outdoor type LT panel board, totally enclosed, dust, weather and vermin proof 1100 Volt grade, 50 HZ supply made out by 3.15mm thick CRCA sheet for load bearing and 2mm thick for non load bearing, fully compartmentalised, with IP - 65 protection, painted with powder coated paint, angle iron padastal frame with necessary brick work and grouting 600mm hight above ground level all as per conforming to IS-2417 of 1962, complete including the following accessories for each set all as specified and directed. (Loc- Sahyadri AC)

(a) 4 Nos bus bar of equal size made out of copper strip of suitable size with PVC insulated coloured heat shrinkable type sleeves, of rating 600 Amps, for looping and branch connection system, mounted on non cracking resin type insulators - 01 Job. (b) TPN, 4 Pole, MCCB ( thermal magnetic release) 400 Amps, 415 Volt, 36KA - 01No. (incoming) (d) TPN, 4 Pole, onload change over switch front operated 400 Amps, 415 Volt- 01No. (c) TPN, 4 Pole, MCCB ( thermal magnetic release) 100 Amps, 415 Volt, 25KA - 05No. (Outgoing) (d) TPN, 4 Pole, MCCB ( thermal magnetic release) 63 Amps, 415 Volt, 25KA - 02No. (Outgoing) (e) SPN, MCB 63 Amps, - 02No. (Outgoing) (f) SPN, MCB 32 Amps, - 02No. (Outgoing) (g) Indication lamps R, Y & B - 01 Set (h) Provisioning of copper tinned cable glands for incoming and outgoing cables - 01 Job. (j) Provision of multi functional meter. with CTs and PTs (Volt, amp, hz)-01 set (k) Provn of 3 Ph digital energy meter with Cts ( KWh)- 01 No

Nexus Infratech