Est of 2x20MVA 66/11kV SS at Belaghatta and construction of 66kV DC Line along with Replacement of existing Coyote Conductor by HPC of ampacity 700A Conductor for a distance of 11.394km and Construction of 66kV SC Link Line for a distance of 0.210km and Construction of 1No. of 66kV terminal bay at 220/66/11kV Substation at Belaghatta in Chitradurga Taluk and District on PTK

Karnataka Power Transmission Corporation Limited

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

TECHNO - COMMERCIAL SHEETS

NOTE* For detailed scope of the work please refer Bid Documents.

BIDDERS TO READ CAREFULLY

THE FOLLOWING DOCUMENTS [DULY SIGNED BY AUTHORISED PERSON, WHEREVER NECESSARY] ARE TO BE UPLOADED AND BANK GUARANTEE/INSURANCE SURETY BOND TOWARDS EMD OVER AND ABOVE RS.1.00LAKH AS PER ANNEXURE-II OF THE BID DOCUMENT SHALL BE SENT IN ORIGINAL TO CHIEF ENGINEER ELECTY., (T&P), KPTCL, BENGALURU SO AS TO REACH THIS OFFICE AFTER THE LAST DATE OF SUBMISSION OF BID AND ON OR BEFORE THE DATE & TIME NOTIFIED FOR OPENING OF TECHNO COMMERCIAL BIDS, FAILING WHICH THE BID WILL NOT BE OPENED. 1) NO DEVIATION CERTIFICATE (SCHEDULE-16). 2) EMD/BID SECURITY AS DETAILED IN CLAUSE NO. 13 of ITT. 3) BANK GUARANTEE issued either by a Nationalized/Scheduled Bank OR INSURANCE SURETY BOND issued by Insurance Company authorized by Insurance Regulatory and Development Authority of India (IRDA) TOWARDS BALANCE EMD/BID SECURITY. (For the balance EMD above Rs. 1.00Lakh) (SCHEDULE-17) - as detailed in Clause No. 13 of ITT-The Bidder shall scan the Bank Guarantee/INSURANCE SURETY BOND towards EMD and upload the same in the prescribed format in the slot specified for “EMD and Tender Fee Payments” in the e-procurement portal to enable the owner for verification of EMD BG/ISB at the time of opening of Techno Commercial Bid, failing which the offer will be rejected. 4) LETTER OF UNDERTAKING (SCHEDULE-18). 5) CONSORTIUM AGREEMENT (IF APPLICABLE-SCHEDULE-19) 6) POWER OF ATTORNEY (SCHEDULE- 20). 7) ANY OTHER AGREEMENTS /UNDERTAKINGS/SELF DECLARATIONS SPECIFIED IN THE TENDER.

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

BID PROPOSAL SHEET

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidder's Name & Address alongwith GSTIN no. :

Bid Proposal Reference :

Person to be contacted :

E-Mail Address:

The Chief Engineer, Electricity,

Tendering & Procurement, KPTCL,

9th Floor, Indhana Bhavana, A.R Circle, Bangalore - 560 009.

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

a) * We have submitted bid as individual Bidder. (Indicate Name of the Individual Bidder)

b) * We have submitted bid in Consortium with the following Bidders. (Key in Consortium)

Name of the Consortium Partner Scope / Participation of each Consortium Partner

(* Fill-up whichever is applicable)

1 We, the undersigned Bidder, having read and examined in detail the specifications and all the Bidding documents of the said work and hereby propose to design, manufacture/fabricate, shop test, supply on FOR site basis, and carry out the erection, testing and commissioning including civil, structural and architectural works for

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

2 PRICES AND VALIDITY :

2.1 We declare that the Prices stated in our Proposal are in accordance with subject Bid Documents (including Clause No.40 of "Conditions of Contract (CC)" & Clause No.12 of Instruction to Tenderers (ITT) of Bid Documents. We further declare that all Ex-works price/CIF components of Spares, Maintenance and Testing Equipments and other charges viz., Freight and Insurance, Type Test charges and other charges stated in our proposal shall be as per the Tender conditions. All the Price and other terms and conditions of this Proposal are valid during the Performance of the Contract.

2.2 All Duties, such as Custom Duties on imports, Levies, Surcharge/Cess etc., if any applicable on the transaction excluding GST are included in the Bid Price and shall be to Our account and the Owner is not having any liability whatsoever on this account, whatever may be the contrary elsewhere in the Bid documents. However the component of Duties included in the Bid Price are separately indicated in Schedule - 2 for TDS purpose. We further confirm that our Bid Prices as quoted in Schedule-I, include all import Duties and levies including Licence fees lawfully payable by us on imported items and all other Duties and Levies applicable on Bought-out Components, Materials, Equipment and other items and confirm that any such Duties and Levies additionally payable shall be to our account. We further confirm that, no Sales Tax in any form shall be payable by Owner either for Bought-out items which are despatched by our Sub-Suppliers directly to the Project Site or for items Supplied directly by us. We confirm that, the Prices quoted by us are excluding GST.

2.3 We declare that we have noted and considered Clause No.39 of Conditions of Contract (CC ), Clause No. 11.11 of Instruction to Tenderers(ITT) of Bid Documents regarding Taxes and Duties and quoted our Prices accordingly. We further agree for TDS as per Statutory stipulations.

2.4 The Bid Prices, the Price components of the various items in our Scope of Supply, Erection including Testing & Commisisoning, Civil and Mandatory spares is quoted in Percentage rate Financial Bid in KPP Portal for this proposal..

3 CONSTRUCTION OF THE CONTRACT : We, declare that we are making the Offer on the basis of Single Contract for the entire Scope of the Package in accordance with Clause No.26.2 of Instruction to Tenderers (ITT) of Bid Document.

4 We having studied Clause No.39 of Conditions of Contract (CC ), Clause No. 11.11 of Instruction to Tenderers(ITT) of Bid Documents , relating to Tax and we hereby, declare that if any income-tax, surcharge on income tax or any other corporate tax is attracted under the law, we agree to pay the same.

5 Bid Security/ EMD : We have enclosed a Bid Security through e-Payment mode for a sum of Rs.1.00Lakh and remaining amount of Rs..........Lakhs ( above Rs.1.00 Lakh) in the form of Insurance Surety Bond (ISB) issued by Insurance Company authorized by Insurance Regulatory and Development Authority of India (IRDAI) OR in the form of Bank Guarantee in original valid for a period of 225 days from last date of bid submission and liable to be forfeited in accordance with Bid Documents. (Mode of Payment towards EMD is as detailed in CLAUSE NO. 13 of ITT & Clause No. 5 of NIT)

We have also ensured that the above Bid Guarantee furnished by us is in line with the Bid Documents and complete in respect of following :

1. Value of Non judicial Stamp Paper purchased in the name of executing Bank is as per Stamp Act.

2. Power of Attorney Number and Date as well as Signature and Full Name and Designation of Executant along with Bank's Stamp are there.

3. Signature, Full Name, Designation and address of Witness are there.

4. Completed Mailing address of the Head Office of the Bank is indicated.

6.1 We declare that the Works shall be performed strictly in accordance with the Specifications and Documents except for the variations and Deviations, all of which have been detailed out exhaustively in the following Schedules, irrespective of whatever has been stated to the contrary anywhere else in our Proposal.

a Commercial Deviations Schedule Schedule - 5

b Technical Deviations Schedule Schedule - 6

6.2 We further confirm that Specified Stipulation of following Clauses are acceptable to us and No Deviation / Exceptions are taken on any account whatsoever in the following Clauses.

a. Terms of payment Clause No. 37 of Section-5,Conditions of Contract (CC) and Clause No.8 of Special Conditions of Contrac (SCC)

b. EMD/Bid Security Clause No. 6, Section :1, Invitation for Tenders (IFT) and Clause No. 13, Section :2, Instruction to Tenderer (ITT)

c. Contract Performance Guarantee Clause No. 29 of Section:2, Instruction to Tenderers (ITT).

d. Penalty for delay Clause No. 41 of Section-5 : Conditions of Contract (CC).

e. Price Basis/ Price adjustment Clause No. 40 of Section-5 :Conditions of Contract (CC).

f. Defects Liability Period/Guarantee Clause No. 10 of Section-5 Special Conditions of Contract (SCC)

g. Work Schedule Clause No.17 of Section:5 Conditions of Contract (CC)

h. Taxes and Duties Clause No. 11.11 of Section-2: Instruction to Tenderers (ITT).

Further, we agree that additional conditions, if any, found in the Proposal Documents other than those stated in Deviation Schedules, save that pertaining to any rebates offered, shall not be given effect to.

7 PERFORMANCE GUARANTEE ; We declare that the ratings and performance figures of the equipment to be supplied and erected by us are guaranteed. The Guaranteed particulas of different equiment in our Scope are enclosed in Data Requirement Sheets.

8 BID PRICING : We further, declare that the Prices stated in our Proposal are in accordance with your ITT & SCC & all other relevant clauses of Bid Documents.

9 PRICE ADJUSTMENT : We declare that the Prices quoted by us are in accordance Clause No. 40 of Section-5 :Conditions of Contract (CC)

10 SPECIAL TOOLS AND TACKLES : We have given a list of Special Tools and Tackles in Schedule - 7 and Prices thereof are included in our lumpsum Bid Price. We further agree that any items of Special Tools and Tackles, though not included in the aforesaid list, but required for effective Erection, Testing, Commissioning & Operation of the Equipments of Substations & Transmission lines shall also be furnished by us, at no extra cost to you.

11 ADDITIONAL INFORMATION : In addition to the information called for in these Proposal Sheets, we have included with this Proposal, additional information as listed in Schedule - 8. We further confirm that such additional information does not imply any additional deviation beyond those covered in Schedule - 5 & 6 and in case of any contraction between these additional information and other provisions of Bid, the later will prevail.

12 QUALIFICATION DATA : We confirm having submitted the Qualification Data, as required by you in your Bid Documents in e-Procurement Portal along with this Proposal. Further we have filled in the information for Qualification Requirements in Schedule 9. In case you require any further information in this regard, We agree to furnish the same in time.

13 WORK SCHEDULE : If this Proposal is accepted by you, we agree to submit Engineering Data, Provide Services and complete the entire Work from time to time, in accordance with Schedules indicated in the Proposal. We fully understand that the Time Schedule stipulated in this Proposal is the essence of the Contract, if awarded. The completion schedule of the various Major Key Phases of the Work is indicated in Schedule - 11.

14 CONTRACT PERFORMANCE GUARANTEE ; We further agree that if our Proposal is accepted, we shall provide an irrecoverable Contract Performance Guarantee, of value equivalent to Five percent (5%) of the Amount Put to Tender (Excluding GST) plus additional security for unbalanced tenders in accordance with Clause 29 of Instructions To Tenderers (ITT) of the tender valid up to the end of ninety (90) days after the end of the Contract Guarantee Period mandatorily in the form of Insurance Surety Bonds (ISBs) issued by Insurance Company authorized by Insurance Regulatory and Development Authority of India (IRDAI) (OR) in the form of electronic Bank Guarantee (e-BG) from the Banks which are integrated with NeSL in the form attached as Annexure-III (Section 4: Formats of Annexures) in your favour in accordance with Clause 25.5 of ITT and Clause 43 of the CC (Conditions of Contract), as per the format given in Section 4 and enter into a formal agreement with you within Twenty (20) days from the date of issue of Letter of Intent to Award the Contract.

15 We, the partners of the Consortium whose Signatures are appended below, shall be liable jointly and severally for the execution of the Contract(s), in the event of Award, in accordance with the terms of Contract(s). The Lead Partner for this Bid - M/s .................................................................................... on behalf of the Consortium, is submitting the Bid. The Power of Attorney in favour of M/s .......................................................................................is enclosed.

16 BID PRICE : We declare that our lumpsum Price for the entire scope of work specified in the specifications and documents, shall be as indicated in Schedule - 1.

17 CHECK LIST : We have included a Checklist duly filled in Schedule 22

18 We, hereby, declare that only the Persons or Firms interested in this Proposal are named herein as Principals and that no other Persons are interested in the Proposal or in the Contract to be entered into, if we are awarded the Contract, and that this proposal is made without any connection with any other Person, Firm or Party likewise submitting a Proposal and that this Proposal is in all respect for and in good faith, without collusion or fraud.

19 We declare, in case our bid is accepted, that until a formal Contract is prepared & executed, this bid together with your written letter of acceptance thereof and your notification of award /Letter of Intent to Award the Contract shall constitute a binding contract between us. We further understand that you are not bound to accept the lowest or any bid you may receive.

Thanking you, we remain,

Yours faithfully,

Place Printed Name

Business Address Country of Incorporation (State or Province to be indicated)

Name and Address Principal Officer

Karnataka Power Transmission Corporation Limited

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

FILL ONLY IN LIGHT BLUE COLOURED CELLS.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer, Electy., Tendering & Procurement, KPTCL, 9th Floor, Indhana Bhavana, A.R Circle, Bangalore - 560009

We declare that in terms of Clause No. 11 of ITT, Bid documents, the following are our lumpsum price in Rupees for the entire scope of work as specified in the Specifications and Documents.( Inclusive of all Taxes (Excluding GST) & Duties).

Total Lumpsum Price : ( In Figures)

Total Lumpsum Price : ( In words)

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 2 (1 of 2)-SUMMARY OF PRICE COMPONENTS

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

FILL ONLY IN LIGHT BLUE COLOURED CELLS.

Summary of Price Components

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer, Electy., Tendering & Procurement, KPTCL, 9th Floor, Indhana Bhavana, A.R Circle, Bangalore - 560009.

Summary price components for identified in accompanying specifications

( Name of the Work) as per the scope identified in accompanying specifications.

Sl no Description Amount in Rs. (Fill as "YES" against the above Price columns in case Prices are indicated in the Price templates)

Establishing Sub station Construction of Transmission Lines

A Material / Equipment Price (including Packing & Forwarding charges) in the Scope of the Contractor

Ex-works including all taxes & duties [As per schedules - 3A(i) for Station & 3B(i) for Line]

ii) Freight and Insurance Charges (Not Applicable) [As per schedules - 3A(i) for Station & 3B(i) for Line]

iii) Total FOR site price (i+ii)

B Mandatory spares price (including packing & forwarding charges)

Ex-works including all taxes & duties(As per schedule - 4)

ii) Freight and Insurance Charges(Not Applicable) (As per schedule -4)

iii)Total FOR site price (i + ii)

C Supply portion total FORD price [A+B]

D Erection portion:

i) Total charges for Erection, Testing & Commissioning of all Supply items [as per schedules-3A(ii) for Station, 3B(ii) for Line]

ii) Total charges for entire civil works [ as per Schedules-3C(i) for Station and 3C(ii) for Line]

iii) Total civil works, erection, Testing and commisioning charges (i)+(ii)

E Total Bid Price = C+D(iii) In figures : Rs.

Total Bid Price in Figures : Rs.

Total Bid Price in words : Rupees

Note: The erection charges shall include the charges for taking delivery at Owner's store, unloading, handling, storage, erection, testing and commissioning of all equipments and applicable GST.

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 2 ( 2 of 2 ) - TAXES (Excluding GST), DUTIES & OTHER LEVIES

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Fill IN LIGHT BLUE COLOURED CELLS.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer, Electy., Tendering & Procurement, KPTCL 9th Floor, Indhana Bhavana, A.R Circle, Bangalore- 560009.

Estimates of Indian Taxes (Excluding GST), Duties and Levies included in the Total Bid Price are as follows:

SL. No. Description of Applicable Tax (Excluding GST) / Duty / Levy Establishing Sub station Construction of Transmission Lines

Rate of Tax (Excluding GST)/ Duty / Levy Amount of Taxes (Excluding GST) / Duties in Rupees Rate of Tax (Excluding GST) / Duty / Levy Amount of Taxes (Excluding GST)/ Duties in Rupees

1 Applicable taxes (Excluding GST), duties & levies prevailing as on the last date of bid submission shall be quoted

i. Supply Portion

ii. Erection Portion

iii. Civil Portion

i. Supply Portion

ii. Erection Portion

iii. Civil Portion

i. Supply Portion

ii. Erection Portion

iii. Civil Portion

6 Building and other construction workers welfare Cess for Supply, Erection and Civil Portion works

8 a. Applicable Customs Duty (*) (Bidders shall also clearly indicate the breakup of Customs duty such as BCD, Cess,etc.,)

b. If there is any existing Treaty between India and the country from where the goods required for this project are proposed to be imported, then copy of the treaty shall be uploaded.

9 Other Taxes & duties if any (Specify) **

10 Other Taxes & duties if any (Specify) **

11 Total (Sum of 1 to 10)

(*) In case of CIF portion of Supply.

** Please Specify the nature of the other Taxes (Excluding GST) along with the details in the "Rate" Column.

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 2A : SCHEDULE OF DISCOUNT

SHEET FOR TECHNOCOMMERCIAL OPENING (UN - PRICED)

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

FILL ONLY IN LIGHT BLUE COLOURED CELLS.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer, Electricity, Tendering & procurement, KPTCL, 9th Floor, Indhana Bhavana, A.R Circle, Bangalore - 560009.

We hereby offer an unconditional discount on our quoted price in Schedule 2 (1 of2) as under. Any discounts offered anywere else in Bid shall not be considered.

Sl.No Nature of Discount Establishing Sub station along with construction of associated Transmission Lines

Percentage of discount Amount (in Rs.) Remarks

I Supply Schedules

b) Freight & Insurance (Not Applicable)

II Erection Schedules

III Civil Works Schedules

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE- 2 B - STATEMENT OF COMMERCIAL TERMS AND CONDITIONS

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Details of payments made in the form of Credit card/Debit card/NEFT/RTGS/OTC (over the counter) as per the tender conditions should be keyed in against column no.3 (a) . BG Amount, BG No. and date, Name and address of the bank issuing the BG, validity of the BG should be keyed in against column no. 3 (b) .

FILL ONLY IN LIGHT BLUE COLOURED CELLS.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer, Electy., Tendering & Procurement, KPTCL, 9th Floor, Indhana Bhavana, A.R Circle, Bangalore - 560009.

STATEMENT OF COMMERCIAL TERMS AND CONDITIONS

Sl. No. Particulars Details

1 Bid proposal form Uploaded.

2 No deviation certificate Uploaded.

3. a). EMD / Bid Security Bids shall be accompanied by bid security (EMD); 1) Up to Rs.1.00Lakh The following modes of payment will be provided as a part of e-Payment services. • Credit Card/Debit Card • Net Banking • NEFT/RTGS • Over-the-Counter (OTC) • IMPS For further detail regarding mode of e-payment of EMD in e-procurement platform, contact e-procurement cell, Government of Karnataka.

b). EMD amount above Rs.1.00Lakh by Bank Guarantee/Insurance Surety Bond (ISB)

4 Validity of the Bid.

5 Qualifying Requirements.

6 Financial capability

8 Taxes & Duties.

9 Completion Schedule

10 Defects Liability Period/Guarantee

11 Payment Terms

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3A(i) - Price Breakup for - Station Supply portion

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidder's Name & Address alongwith GSTIN no. :

The Chief Engineer, Electricity, Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore-560009.

BIDDERS SHALL FILL ONLY IN THE LIGHT BLUE COLOURED CELLS.

Station Supply portion :

Sl No Name of the Equipment/Materials Unit Total Quantity Indicate whether "Own manufactured Item" or "Bought Out Item"

SS1 STATION SUPPLY PORTION: Power Transformers: 20MVA, 66/11kV TRANSFORMER. 66/11KV, Delta/Star, Dyn11, 3-Ph, 50Hz, Core Type, 2 Winding Delta/Star transformer, vector group DYn11 with OLTC ONAN/ONAF with fan control cubicle, RTCC Panel, first filling of Oil and 10% spare oil in non-returnable drums etc., and 2 Nos. of 11kV Insulated copper flats for each phase from LV side of transformer to cable at cable terminating structure with suitable support bracket and support insulators for LV side copper flat bus and 2 Nos. of Copper Flats from Neutral Terminal to the Earthmat through NCT and necessary Support Pin Insulators as per technical specification.. Note: 1. Terminal connectors suitable for Drake/Moose ACSR on primary side of transformer and copper flat on 11kV and connectors for Neutral suitable for 2 Nos. of Copper Flats as per technical specification. 2.Copper Flats required for Power Transformers shall be supplied along with the Transformers as per Technical Specifications. No 2

SS2 Nitrogen Injection fire extinguishing system-supply, erection & commissioning works etc., as per technical specification for 20MVA Power Transformers No 2

SS3 CIRCUIT BREAKER : SF-6 Circuit Breaker with terminal connector suitable for Moose ACSR conductor / 63mm Al. pipe with spring/semi-pneumatic/pneumatic type operating mechanism and mounting structure etc.,as per technical specification 72.5 kV, 2500 A, 40 KA Class SF6 CB i)For 66kV Line No 3

SS4 ii)For 66/11kV Power transformer No 2

SS5 ISOLATORS : 66kV, 1250 A, 40kA double break manually operated isolators with solid core Cylindrical post insulator, terminal connector suitable for Drake ACSR conductor/ 63mm/75mm Al. pipe conductor, marshalling box etc., complete as per technical specification Note:Terminal Connectors for isolators shall be as follows For Substation :Rigid Type suitable for Drake ACSR -36Nos Flexible Type suitable for 75mm Al Pipe-00Nos Flexible Type suitable for 63mm Al Pipe-18Nos i)Upright mounting type with Earth switch.LPH 4600mm Set 3

SS6 iii)Upright mounting type without Earth switch. LPH 6350mm. Set 6

SS7 11kV Isolators: 11kV isolator, Double break 400 A, 25KA capacity with rigid bi-metallic terminal connector suitable for coyote ACSR conductor.(Capacitor Bank) Set 4

SS8 11kV isolator, Single break 400A, 25KA capacity with Roaster Switch with bi-metallic terminal connector suitable for coyote ACSR Conductor. Set 11

SS9 CURRENT TRANSFORMER : Current transformers including marshalling boxes, Single phase,oil filled outdoor type with rigid bimetallic terminal connectors suitable for or Drake ACSR conductor / 63mm Al. pipe as per technical specifications. i)66kV class, 40KA, CT of ratio 800-400 / 1-1-1A for Tr.Line. Core-1:Dist/diff. Acc class PS, Vk-1400V at 800A, Rct-5ohm at 800/1A. Core-2:For metering : Accuracy 0.2s, Burden 10 VA Core-3:For backup protetion : Accuracy 5P20. Burden 30 VA No 6

SS10 ii)66 kV class, 40 KA, CT of ratio 400-200 / 1-1-1A for Tr. lines. Core-1: Vk-1600V at 400A, Rct 4ohm at 400/1A, Accuracy class PS- Dist/Dif Core-2: For metering : Accuracy 0.2s, Burden 10 VA Core-3: For backup protetion : Accuracy 5P20. Burden 30 VA No 3

SS11 ii)66 kV class, 40 KA, CT of ratio 200-100 / 1-1-1A for Transformer. Core-1: Vk-800V at 200A, Rct 2ohm at 200/1A, Accuracy class PS- Dist/Dif Core-2: For metering : Accuracy 0.2s, Burden 10 VA Core-3: For backup protetion : Accuracy 5P20. Burden 30 VA No 6

SS12 11kV class, 25 KA, NCT of ratio 1200-800/1-1-1A for REFR protection(of similar rating and ratio as that of Incomer of 11kV switchgear) with terminal connector suitable for 2 Nos of Copper flats as per technical specification. NOTE:1. For details refer Annexure-IIB. Technical Paramaters of current Transformers for type and rating attached at the end of this schedule. 2) All the Current transformers in each KV class shall be of One and the same make for interchangeability and reliability of performance. 3) The characteristics of 11kV NCT should be the same as that of the incomer CT of 11kV Switchgear 4) The Terminal connectors for 11kV NCT shall be suitable for 2 nos. of Copper flat as per technical specification. No 2

SS13 VOLTAGE TRANSFORMER : VOLTAGE TRANSFORMER Single phase, oil filled, outdoor type VT with rigid bimetallic terminal connector suitable for Drake ACSR Conductor with marshalling box etc., complete as per technical specification. Ratio: 66kV/sqrt(3)/110V/sqrt(3) - 110V/sqrt(3)-110V/sqrt(3) Core - 1 : 300 VA, Accuracy class 0.2. Metering Core - 2 : 200 VA, Accuracy class 3P. Protection Core - 3 : 50 VA, Accuracy class 3P. Open / delta No 3

SS14 SURGE ARRESTOR (Porcelain Housing) metal oxide, Gapless type, as per Technical Specification: i) 60 kV, 10KA Metal Oxide with surge counter Arrestor class : Discharge Class 3 (Station Medium Duty (SM)- for overhead lines No 9

SS15 ii)60 kV, 10KA Metal Oxide with surge counter Arrestor class : Discharge Class 3 (Station Medium Duty (SM))- for Transformer No 6

SS16 iii)9kV, 10KA class station class with connector and clamp No. 33

SS17 Capacitor Bank: Design, Engineering, supply, erection, testing & commissioning of 2.9 MVAR, 12.1 kV Capacitor Bank, star connected, Double Bank with internal fuses, terminal connectors with suitable neutral CT and station class LAs, 0.2% series reactor on neutral side with mounting structures for NCT, Capacitor Bank, station class LAs, Series reactor etc, and with 10% Spare Capacitors complete as per specification Note : For 11kV Switchgear & remote announciation /control of the Capacitor Bank refer Techno-commercial sheet. Set 4

SS18 Control and Relay Panel: Simplex 110V DC compatible to SCADA complete as per technical specification: i)For Power transformer 66/11 kV Note: 1. All the C&R Panels and associated panels shall be of one and the same make for uniformity and interchangeability of Components. 2. The accuracy class of metering core of CTs and ETV meter of C&R panels shall be 0.2s accuracy class and for VT 0.2 accuracy class irrespective of what has been indicated else where in the bid document. 3. The electronic Tri-vector meter of 0.2s accuracy class with ABT & TOD features, DLMS protocol energy meter has to be provided both on HV and LV side of C&R Panel. 4.All numeriacal relays shall conform to IEC Protocol as per technical specification. 5. 66KV Relay and protection panel shall be in conformity with technical specifications of relay and protection panel with SCADA compatibility. No. 2

SS19 ii)For 66kV Transmission line No. 3

Station Structures : 66kV Side station structure fabricated out of galvanized mild steel including Bolts and Nuts as per specifications. i) Station towers fabricated out of galvanised mild steel(verticals 1T1) (1.054t/tower) (0.9860 t per tower for structure+0.0680 t per tower for Bolt & Nuts per structure) t 4/4.216

ii) Station Beams fabricated out of galvanised mild steel. Beam type 1B1 with peak.(8.2 mtr bay width)( 0.553t/tower) (0.5210 t per tower for structure+0.0320 t per tower for Bolt & Nuts per structure) t 3/1.659

iii) Tubular type Lighting / lighting Mast (approx wt. 2.812 t) (2.6714t per tower +0.1406t for Bolt & Nuts per structure) t 1/2.812

iv) Street lighting lattice type structure along with GI pipe for fixing of LED lamp (0.182 MT )-8.5 mtr height(0.182t per structure+0.0091 t for Bolt & Nuts per structure) t 12/2.2932

MOUNTING STRUCTURES including Bolts and Nuts as per specifications. i) Isolators Live point height 4600mm. (0.752 t)(0.7260t per structure+0.0260t for Bolt &Nuts per structure) t 3/2.256

ii) Isolators Live point height 6350mm. (0.982t)(0.9550t per structure+0.0270 t for Bolts & Nuts per structure) t 6/5.892

iii) Current transformer.66kV (0.158 MT)(0.1460t per structure+0.0120t for Bolts & Nuts per structure) t 15/2.37

iv)11 kV NCT (0.157 t)(0.1460t per structure+0.0110t for Bolts & Nuts per structure) t 2/0.314

v) Voltage transformer (0.148 t per structure)(0.1370t per structure+0.0110t for Bolts & Nuts per structure) t 3/0.444

vi) Lightening arrestors (0.116 t per structure)(0.1050t per structure+0.0110t for Bolts & Nuts per structure) t 15/1.74

vii) Pedestal insulators (0.141 t per structure) (0.129t per structure+0.012t for Bolts & Nuts per structure) t 12/1.68

viii) For High pedestal insulators (0.150 t per structure)(0.1340t per structure+0.0160 t for Bolts & Nuts per structure) t 6/0.9

ix) 11KV Cable Terminating Structure for LV Side of Transformer(0.072 t Per Structure)(0.0690t per structure+0.0030 t for Bolts & Nuts per structure) t 2/0.144

x) 11KV GOS/Cable Terminating Structure for 11KV Capacitor Bank(0.158 t per structure)(0.1501t per structure+0.0079t for Bolts & Nuts per structure) t 4/0.632

SS20 Total Weight of Fabrication, galvanising and supply of Mild Steel of Station structures and Mounting Structures. Note :- Rate to be quoted on per tonne basis t 25.8048

SS21 Total Weight of supply of Bolts & nuts of of Station structures , Mounting Structures , Lightning Mast & street lighting. Note :- Rate to be quoted on per tonne basis t 1.5474

SS22 C) 11 kV ODS and take off structure : Supplying of Double pole structure with 9.5 Mts. RCC poles,300Kg WL and with provision for fixing 11 kV 400 A Roaster single break isolators & provision for fixing 9kV lightning arrestors complete set with wiring materials (including DP Set, Pin Insulator, Pin for Insulator and H frame) Set 11

SS23 BUS BAR FORMATION : (iMoose ACSR-66kV side mtr 350

SS24 (ii)Coyote ACSR mtr 80

SS25 Rigid Bus with Taps & Clamps : 66kV side: i) Aluminium pipe conforming to 6340WP of IS - 5082 / 1969 (BS I600-Sch. 40) of following nominal diameter a) 75mm Mtr 60

SS26 b) 63mm size connecting isolator to vertical tap Mtr 108

SS27 ii)Straight taps suitable for 63mm Aluminium tube (BS-1600) of 1750mm vertical height for vertical portion & cross bus on 66KV side with rounded off end. Nos 9

SS28 iii) Post insulator clamps suitable for 75 mm Aluminium pipe & Post insulator solid core insulator type - 66kV side a)Rigid Type Nos 3

SS29 b) Expansion Type Nos 3

SS30 c)Sliding Type Nos 6

SS31 iv) Corona Bell Suitable for Aluminium Pipe of size 75mm on 66 kV Nos 6

SS32 INSULATORS: i) Post insulators- Cylindrical solid core as per technical Specification Solid Core Bus Post Insulator 66kV class, 1Unit/stack. Nos 18

SS33 HARDWARES : 1.C Type wedge connector suitable for Drake-HPC Conductor No 18

SS34 2.Post insulator clamp suitable for Drake ACSR and 66kV solid core Insulator Nos. 6

SS35 Auxiliary Transformer: Station Auxiliary Transformer with Copper winding & oil, outdoor type, 100 kVA, 11kV/433 V, 3 Ph, Vector group Dyn11, off load tap changer (with 5 taps) with step voltage of 2.5% as per technical specification. No. 1

SS36 Double Pole Structure along with 9.5 mtr RCC pole, DP Set, H Frame, 11kV 400A Double break isolator and 9kV, 10kA surge arrestor (3 Nos), HG Fuse Unit,Angle for fixing HG fuse unit( pole clamps bolt & nuts etc) PIN insulator, PIN for insulator, LT Distribution Box and Tri vector Meter, & complete set for auxiliary Transformer etc set 1

SS37 A) LTAC Panel (Indoor), 415 V as per technical specification comprising of voltmeter and ammeter,1 I/C MCCB 200A + 2 nos. 3 Phase 63A O/G SFU, + 2 nos. 3 Phase 32A O/G SFU 100A + 14 O/G SFU, 6 nos. 3 Phase 16A SFU etc., complete as per technical specification. No 1

SS38 B) A.C. Distribution Box (Outdoor) : AC Distribution Box Single front (Outdoor type) 6 Terminal, one I/C of 100A MCCB 20kA + 6 O/G MCB 16A + 1 O/G of 100A, HRC fuse, complete as per technical specification. No 1

SS39 LT Power Cable:1.1 kV Class Armoured Aluminium Cable with glands/lugs/ferrules : a) 1.1 kV PVC Insulated 4X95 sq.mm Aluminium cable 4 core with glands / lugs / ferrules Mtr 300

SS40 b) 1.1 kV PVC Insulated 4X25 sq.mm Aluminium cable 4 core with glands / lugs / ferrules Mtr 300

SS41 c) 1.1 kV PVC Insulated 4X10sq.mm Aluminium cable 4 core with glands / lugs / ferrules Mtr 300

SS42 STATION BATTERY: 110V, 200AH, Battery set Plante/Grid/Nickel Cadmium Type as per technical specification Set 1

SS43 BATTERY CHARGER : Battery charger suitable for 110V, 200 AH, Battery set Plante/Grid/Nickel Cadmium Type with float cum booster type battery charger as per technical specification. Set 1

SS44 DC Distribution Panel (Indoor) as per technical specification comprising of earth fault indicator, indication circuit for AC mains failure, 1 no. 100A SFU for I/C + 12 nos. 32A SFU for O/G, complete as per technical specification. Nos 1

SS45 Copper control cables: 1.1kV class PVC insulated Copper Control Cable with Lugs / Ferrules, Glands as per specificaions i) 19 Core x 2.5 Sq.mm. Mtr 2000

SS46 ii)10 Core x 2.5 Sq.mm. Mtr 2000

SS47 iii) 4 Core x 6.0 Sq.mm. Mtr 2000

SS48 iv) 4 Core x 2.5 Sq.mm. Mtr 1000

SS49 v) 2 Core x 2.5 Sq.mm. Mtr 300

SS50 vi) 2 Core x 6 Sq.mm. (Yard Lighting-1280Mtr is included) Mtr 2480

SS51 11kV Switchgear:11kV, 25KA, 500 MVA MCVCB switchgear 1600 A for incomer and 1250 A for feeders (SCADA Compatable) Out door type comprising of 2IC+12F+1BC+4CB+1AP (Remote annunciation cum Control panel) with CTs & PTs etc.,complete as per technical specification Note: 1. The switchgear for capacitor bank shall have necessary Over voltage / Under voltage /Timer/ Circulating current relays and other protection relays as per specification 2. The Remote Announciation cum Control panel is Simplex type. 3.The Electronic Trivector meters with 0.2s accuracy class with ABT & TOD features & DLMS ICS compliant features has to provided. 4.The Switchgear will be supplied by KPTCL and the Bidder has to quote for complete scope of erection of Switchgear including moving the Switchgear from the point of unloading to the point of erection, erection of the complete Switchgear, wiring of Switchgear, testing & commissioning etc., complete. Set (KPTCL Supply) 1

SS52 11kV, XLPE Insulated UG Cable as per Technical Specification a) 11kV Single Core, 1000 sq.mm Aluminium cable To be run from 66/11 kV transformers to 11kV switchgear). Mtr 550

SS53 b) 3X240 sq.mm Aluminium cable (To be run from 11 kV switchgear to 11kV take off DP structure) Mtr 500

SS54 c)3X95 Sq.mm Aluminium Cable( To be Run from 11kV Switchgear to Auxiliary Transformer) Mtr 50

SS55 d)ia Cable Termination kits suitable for 95Sq. mm 3 Core as per techincal specification. Indoor type Nos 1

SS56 d)ib)Cable Termination kits suitable for 95Sq. mm 3 Core as per techincal specification. Outdoor type Nos 1

SS57 d)iia) Cable Termination kits suitable for 240Sq. mm 3 Core as per techincal specification. Indoor type Nos 15

SS58 d) iib) Cable Termination kits suitable for 240Sq. mm 3 Core as per techincal specification. Outdoor type Nos 15

SS59 e)iiia) Cable Termination kits suitable for 1000sq mm Single Core as per techincal specification. Indoor type Nos 14

SS60 d) iiib)Cable Termination kits suitable for 1000 sq mm Single Core as per techincal specification. Outdoor type Nos 14

SS61 Equipments required for establing SCADA Communication as per KPTCL Specification Note:1. Satellite communication required will be arranged by SLDC a. Remote Terminal Unit (RTU) 64 (I/O) Port Nos 1

SS62 b.Data Concentrator Unit (DCU) Nos 1

SS63 c.2kVA online UPS (230V AC 1 phase 50Hz) Nos 1

SS64 SCADA Cables: i)Current Cables - copper core with c/s 4.0sqmm multistrand 4 core Mtr 40

SS65 ii)Voltage Cables-Copper core with c/s 2.5sqmm multistrand 4core Mtr 20

SS66 iii) Signal cables- armoured copper core with c/s 0.5sqmm multistrand 10core Mtr 500

SS67 iv)Control cables - copper core with c/s 1.5sqmm multistrand 10core Mtr 160

SS68 v)supply cables- Copper core with c/s 4.0sqmm multistrand 3core for AC input to UPS and UPS to RTU, conforming to KPTCL specfications. Mtr 15

SS69 vi) supply cables-1C x 32 Sq mm multistrand for battery conforming to KPTCL specification Mtr 30

SS70 Fire Fighting Equipments with necessary Mounting Stands a. i. Mechanical Foam type extinguisher 50 Ltr. capacity Nos 4

SS71 ii. Mechanical Foam type extinguisher 9 Ltr. capacity Nos 4

SS72 b. Water type (gas pressure type) 9 Ltr. capacity Nos 6

SS73 c. Carbon di-oxide type 4.5 kg Capacity Nos 6

SS74 d.i Sand type G.I Buckets 15 Ltr. Capacity Nos 12

SS75 ii. Steel stands for above to have 4 buckets to each stand. Nos 3

SS76 MAINTENANCE TOOLS AND PLANTS 1.Portable (mobile) oil pumps (1/2 HP Air pump 500 to 1000 gallons) Nos 1

SS77 2. Telescopic ladder Aluminium 6 Mtr. Height Nos 1

SS78 3.Ring spanner set- 12Nos per Set Set 1

SS79 4.Tube spanner set- 12Nos per Set Set 1

SS80 5. Pipe wrench 24 inch Nos 2

SS81 6. Pipe wrench 18 inch. Nos 2

SS82 7. Hydraulic Crimping tools up to 1000 sqmm Nos 1

SS83 8.Rubber hand gloves (15 kV tested) Pair 3

SS84 9.Rechargeable 5W LED Hand Torch Nos 4

SS85 10.Insulated cutting plier 12 inch size Nos 3

SS86 11.Insulated cutting plier 8 inch size Nos 3

SS87 12.Line live tester Nos 2

SS88 13.Screw driver 18 inches size Nos 3

SS89 14.Screw driver 12 inches size Nos 3

SS90 15. Hammer 8 lbs Nos 2

SS91 16. Hammer 2 lbs Nos 2

SS92 17. Chain pulley block 5 ton capacity Nos 1

SS93 18.Hydolic jack 5T capacity Nos 4

SS94 19.Pipe derrick suitable for lifting 3 MT and lift of 6 Mtr. height. Nos 1

SS95 20. Allen keys Set 1

SS96 21. Box spanners- 12Nos per Set Set 1

SS97 22.Transil oil di-electric break down (with 2.5 mm gap 0-60 kV) Tester. Nos 1

SS98 23.Insulation Tester Digital Type (megger) 2.5kV - 5 kV Nos 1

SS99 24.Insulation megger 500 V rating Nos 1

SS100 25.SF-6 Gas leak detector Nos 1

SS101 26.Multimeter electromechanical type Nos 1

SS102 27.Multimeter Electronic type Nos 1

SS103 28.Hydrometer Nos 1

SS104 29.DC Voltmeter range -5V to + 5V Nos 1

SS105 30.Hydrometer syring suitable for vent holes Nos 1

SS106 31.Specific gravity correction chart Nos 1

SS107 32.wall mounting type holder for Hydrometer Nos 1

SS108 33.Thermometer with wall mounting holder Nos 1

SS109 34.Rubber appron Nos 1

SS110 35.Pippette Nos 1

SS111 36.Protective goggle Nos 1

SS112 37.Acid resisting jars (4 pint capacity) Nos 1

SS113 38. Rubber shoes knee height Pair 2

SS114 39. Glass funnel No 2

SS115 40. Grounding sticks extendable upto 18 ft : 3 nos. of each 6 ft Sticks of 3 phase R, Y, B (3 nos. of 1 set) Set 6

SS116 Miscellaneous items like rubber mats, first aid box, danger board, shock treatment charts, water filter door locks, fixograph, Sub station name board and other sundry items (size/capacities to be got appfoved). 1.Rubber mats 2000 mm x 1000 mm x 12 mm size Nos 8

SS117 2.First aid box. Nos 1

SS118 3.Shock treatment charts, hard board, liminated with coloured pictures & literature both in Kannada & English. Nos 1

SS119 4. Water filter / Water purifier : Wall mounting type (Aqua-guard type). Nos 1

SS120 5. Sub-station name board duly painted as per specification including erection & Civil Works Nos 1

SS121 6. Fixograph of size 1.5m x 2.5m with English / Kannada alphabets. Set 1

SS122 7.Door locks 7 levers (Navtal make) (Sizes and capacities to be got approved) Nos 5

SS123 8. Danger board ( prohibited ) with support structure including fixing in front of the gate Nos 1

SS124 9. Equipments name plates and earthing name plates including fixing at outdoor yard Nos 60

SS125 Furniture for control room, staff and maintenance, staff, godrej / featherlite / chandan make : 1.Steel Almirahs 6 1/2 feet Nos 2

SS126 2.Steel Almirahs 6 1/2 feet with glass panel doors. Nos 1

SS127 3.Officer's tables Nos 2

SS128 4.Steel slotted angle rack (big) Nos 4

SS129 5.Steel slotted angle rack (small) Nos 4

SS130 6.Steel dust bins Nos 4

SS131 7.Executive Revolving chairs Nos 2

SS132 8.S type arm chairs Nos 6

SS133 9.Steel folding chairs Nos 4

SS134 Station yard lighting (outdoor): i)Supply and installation/ Fixing/ Provision o f Outdoortype Thermoplastic Modular Panel enclosure with transparent Polycarbonate Lid, shockproof, IP65 (WeatherProof), rustproof, dustproof, waterproof, corrosion proof having internally Embedded gasket on both lid and flap suitable to fix Single Phase / Three Phase Energy Metering suitable baseplate and having a provision for Fuse/ MCBcut-out with suitable transparent hinged flap opening for operating MCB along with complete tamper proof SEALING facility,Timer,Contactor,2 Way head frame with diecast LM-6 pulleys ,stainless steel axle,Phosphorus Bronze bearing bush press-fitted with separate guides for 2 runs of 5 mm dia,stainless steel wire rope of AISI304 grade7/19-core, Suitable reversible geared motor operating on 230/415V,50Hz,etc., as per techical specification Each 1

SS135 ii)Supply of LED Street light luminaire with pressure die cast aluminium housing body for optimal thermal dissipation. Lamp compartment comprising of anti glare clear diffuser with Injection moulded polycarbonate material LED streetlight 200W Note: Lightning / Lighting Mast (LM) tubular type are proposed for lightning protection and for illumination of the station Yard. The quantity of lightning / lighting mast indicated are located such that the entire station yard with equipments is protected against lightning. However any additional lighting masts may be provided for sufficient illumination and lightning protection (DSLP) of yard, if necessary. The design of lighting outdoor & indoor is also in the scope of the bidder as specified elsewhere in the technical specification. The scope also includes supply & erection of lighting fixtures, lighting mast panels with timer, contactor, control cable, Motorized hoist etc. Suitable 2.5M Lightning spikes shall be provided on top of GIS building for Lightning protection. The Design of lighting outdoor & Indoor in station yard and GIS buildings etc. is in the scope of bidder as specified in the technical specification. Nos 16

NOTE 1. Any clarifications / hard copy of drawings can be obtained from the office of the Chief Engineer Electricity, Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore.

2. Spacers shall be provided wherever necessary and no extra charges is payable on account of the same.

3. Supply of equipment/materials and the Erection charges shall include loading and unloading.

4. Copper Flat and GI Flat required for Power Transformers (if supply is in Bidder's scope) shall be supplied alongwith the Transformers and no extra cost is payable on this account.

5. The Bidder shall take necessary action to ensure that all the materials supplied shall be properly housed to ensure satisfactory commissioning.

6. The prices for all the materials shall be quoted in the Percentage rate finanacial bid.

7. Released materials shall be transported to the nearest Major Works Store of KPTCL without any additional cost as per the directions of the Engineer in charge of the work.

8. The Bidder shall clearly indicate whether the materials/equipments are “Own manufactured” or “Bought out item”.

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3A(i) - Price Breakup for -Terminal Bay Supply portion

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidder's Name & Address alongwith GSTIN no. :

The Chief Engineer, Electricity, Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore-560009.

BIDDERS SHALL FILL ONLY IN THE LIGHT BLUE COLOURED CELLS.

Station Supply portion :

Sl No Name of the Equipment/Materials Unit Total Quantity Indicate whether "Own manufactured Item" or "Bought Out Item"

TBSS1 CIRCUIT BREAKER : SF-6 Circuit Breaker with terminal connector suitable for Moose ACSR conductor / 63mm Al. pipe with spring/semi-pneumatic/pneumatic type operating mechanism and mounting structure etc.,as per technical specification 72.5 kV, 2500 A, 40 KA Class SF6 CB i)For 66kV Line- No 1

TBSS2 ISOLATORS : 66kV, 1250 A, 40kA double break electrically & manually operated isolators with solid core Cylindrical post insulator, terminal connector suitable for Drake ACSR conductor/ 63mm/75mm Al. pipe conductor, marshalling box etc., complete as per technical specification Note:Terminal Connectors for isolators shall be as follows For Terminal Bay :Rigid Type suitable for Drake ACSR -48Nos Flexible Type suitable for 63mm Al Pipe-12Nos i)Upright mounting type with manually operated Earth switch.LPH 4250mm Set 1

TBSS3 ii)Upright mounting type without Earth switch.LPH 5500mm Set 2

TBSS4 iii)Upright mounting type without Earth switch. LPH 4250mm. Set 1

TBSS5 iii)Underhung mounting type without Earth switch. Set 1

TBSS6 CURRENT TRANSFORMER : Current transformers including marshalling boxes, Single phase,oil filled outdoor type with rigid bimetallic terminal connectors suitable for or Drake ACSR conductor / 63mm Al. pipe as per technical specifications. i)66kV class, 40KA, CT of ratio 800-400 / 1-1-1A for Tr.Line. Core-1:Dist/diff. Acc class PS, Vk-1400V at 800A, Rct-5ohm at 800/1A. Core-2:For metering : Accuracy 0.2s, Burden 10 VA Core-3:For backup protetion : Accuracy 5P20. Burden 30 VA Note : 6 Nos for replacement of existing 400-200/1-1-1A CTS of line bay & bus coupler bay on existing structure. Any modification required for mounting the CTs on existing structure is in the scope of the Bidder No 9

TBSS7 SURGE ARRESTOR (Porcelain Housing) metal oxide, Gapless type, as per Technical Specification: i) 60 kV, 10KA Metal Oxide with surge counter Arrestor class : Discharge Class 3 (Station Medium Duty (SM)- for overhead lines No 3

TBSS8 Control and Relay Panel: 66kV line- Type 6L (as per annexure RPP4- SAS ) with Annunciator and control switches for CB & isolators Note : 1.The accuracy class of metering core of CTs and also Tri vector meter of control & relay panels shall be 0.2s class instead of that of specified elsewhere. 2. Proposed C&R panel shall be interfaced with existing RTU at 220kV Chitradurga ss. No. 1

Station Structures : 66kV Side station structure fabricated out of galvanized mild steel including Bolts and Nuts as per specifications. i) Station towers fabricated out of galvanised mild steel(verticals 1T1) (1.054t/tower) (0.9860 t per tower for structure+0.0680 t per tower for Bolt & Nuts per structure) t 1/0.912

ii) Station Beams fabricated out of galvanised mild steel. Beam type 1B1 with peak.(8.2 mtr bay width)( 0.553t/tower) (0.5210 t per tower for structure+0.0320 t per tower for Bolt & Nuts per structure) t 1/0.594

iii) Tubular type Lighting / lighting Mast (approx wt. 2.812 t) (2.6714t per tower +0.1406t for Bolt & Nuts per structure) t 1/0.448

iv) Street lighting lattice type structure along with GI pipe for fixing of LED lamp (0.182 MT )-8.5 mtr height(0.182t per structure+0.0091 t for Bolt & Nuts per structure) t 0/0

MOUNTING STRUCTURES including Bolts and Nuts as per specifications. i) Isolators Live point height 4600mm. (0.752 t)(0.7260t per structure+0.0260t for Bolt &Nuts per structure) t 2/0.95

ii) Isolators Live point height 6350mm. (0.982t)(0.9550t per structure+0.0270 t for Bolts & Nuts per structure) t 2/1.252

iii) Current transformer.66kV (0.158 MT)(0.1460t per structure+0.0120t for Bolts & Nuts per structure) t 3/0.453

iv)11 kV NCT (0.157 t)(0.1460t per structure+0.0110t for Bolts & Nuts per structure) t 3/0.441

v) Voltage transformer (0.148 t per structure)(0.1370t per structure+0.0110t for Bolts & Nuts per structure) t 6/1.038

vi) Lightening arrestors (0.116 t per structure)(0.1050t per structure+0.0110t for Bolts & Nuts per structure) t 3/0.654

vii) Pedestal insulators (0.141 t per structure) (0.129t per structure+0.012t for Bolts & Nuts per structure) t 0/0

viii) For High pedestal insulators (0.150 t per structure)(0.1340t per structure+0.0160 t for Bolts & Nuts per structure) t 0/0

ix) 11KV Cable Terminating Structure for LV Side of Transformer(0.072 t Per Structure)(0.0690t per structure+0.0030 t for Bolts & Nuts per structure) t 0/0

x) 11KV GOS/Cable Terminating Structure for 11KV Capacitor Bank(0.158 t per structure)(0.1501t per structure+0.0079t for Bolts & Nuts per structure) t 0

TBSS9 Total Weight of Fabrication, galvanising and supply of Mild Steel of Station structures and Mounting Structures. Note :- Rate to be quoted on per tonne basis t 6.4140

TBSS10 Total Weight of supply of Bolts & nuts of of Station structures , Mounting Structures , Lightning Mast & street lighting. Note :- Rate to be quoted on per tonne basis t 0.3280

TBSS11 (iii)Drake ACSR mtr 500

TBSS12 DISC INSULATOR STRING i)11kV , 120KN Disc Insulators Nos 36

TBSS13 DISC INSULATOR STRING i)11kV , 90KN Disc Insulators Nos 36

TBSS14 Aluminium pipe conforming to 63401WP of IS - 5082 / 1969 (BS I600-Sch. 40) of following nominal diameter b) 50mm size connecting isolator to vertical tap Mtr 54

TBSS15 ii)Straight taps suitable for 50mm Aluminium tube (BS-1600) of 1250mm vertical height for vertical portion & cross bus on 66KV side with rounded off end. Nos 3

TBSS16 for Post Insulator clamp suitable for 50mm aluminium pipe and solid core type(sliding type) Nos 3

TBSS17 End cap suitable for 50mm Aluminium Tube Nos 3

TBSS18 INSULATORS: i) Post insulators- Cylindrical solid core as per technical Specification Solid Core Bus Post Insulator 66kV class, 1Unit/stack. Nos 3

TBSS19 Bolted type Tension clamp to suit Drake ACSR 66kV side No 6

TBSS20 Bolted type suspension clamp to suit Drake ACSR No 3

TBSS21 C type wedge connector (T- type) suitable for Drake to Drake ACSR 66kV side No 12

TBSS22 C type wedge connector (T- type) suitable for HPC/Drake to Drake ACSR No 6

TBSS23 2.Post insulator clamp suitable for Drake ACSR and 66kV solid core Insulator Nos. 3

TBSS24 A.C. Distribution Box (Outdoor) : AC distribution box single front type, 6 terminals, 1 I/C of 100A, MCCB 20KA + 6 O/G MCB 16A + 1 O/G of 100A, HRC fuse complete as per technical specification. No 1

TBSS25 c) 1.1 kV PVC Insulated 70sq.mm Aluminium cable 3.5 core with glands / lugs / ferrules Mtr 1500

TBSS26 Copper control cables: 1.1kV class PVC insulated Copper Control Cable with Lugs / Ferrules, Glands as per specificaions i) 19 Core x 2.5 Sq.mm. Mtr 3000

TBSS27 ii)14 Core x 2.5 Sq.mm. Mtr 3000

TBSS28 ii)10 Core x 2.5 Sq.mm. Mtr 2000

TBSS29 ii)7 Core x 2.5 Sq.mm. Mtr 2000

TBSS30 iii) 4 Core x 6.0 Sq.mm. Mtr 3000

TBSS31 iv) 4 Core x 2.5 Sq.mm. Mtr 2000

TBSS32 v) 4 Core x 4 Sq.mm. Mtr 2000

TBSS33 NEW BAY INTEGRATION TO SCADA 8 Channel 220/110 V Opto Coupler Nos 1

TBSS34 Multi Function Transducer (MFT) Nos 1

TBSS35 SCADA Cables: i)Current Cables - copper core with c/s 4.0sqmm multistrand 4 core Mtr 40

TBSS36 ii)Voltage Cables-Copper core with c/s 2.5sqmm multistrand 4core Mtr 20

TBSS37 iii) Signal cables- armoured copper core with c/s 0.5sqmm multistrand 10core Mtr 100

TBSS38 iv)Control cables - copper core with c/s 1.5sqmm multistrand 10core Mtr 100

TBSS39 Miscellaneous items like rubber mats, first aid box, danger board, shock treatment charts, water filter door locks, fixograph, Sub station name board and other sundry items (size/capacities to be got appfoved). 1.Rubber mats 2000 mm x 1000 mm x 12 mm size Nos 2

TBSS40 8. Danger board ( prohibited ) with support structure including fixing in front of the gate Nos 5

TBSS41 9. Equipments name plates and earthing name plates including fixing at outdoor yard Nos 20

NOTE 1. Any clarifications / hard copy of drawings can be obtained from the office of the Chief Engineer Electricity, Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore.

2. Spacers shall be provided wherever necessary and no extra charges is payable on account of the same.

3. Supply of equipment/materials and the Erection charges shall include loading and unloading.

4. Copper Flat and GI Flat required for Power Transformers (if supply is in Bidder's scope) shall be supplied alongwith the Transformers and no extra cost is payable on this account.

5. The Bidder shall take necessary action to ensure that all the materials supplied shall be properly housed to ensure satisfactory commissioning.

6. The prices for all the materials shall be quoted in the Percentage rate finanacial bid.

7. Released materials shall be transported to the nearest Major Works Store of KPTCL without any additional cost as per the directions of the Engineer in charge of the work.

8. The Bidder shall clearly indicate whether the materials/equipments are “Own manufactured” or “Bought out item”.

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3A(ii) - Price Breakup for - Station Erection portion including Testing and Commissioning.

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidder's Name & Address alongwith GSTIN no. :

The Chief Engineer, Electricity, Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore-560009.

BIDDERS SHALL FILL ONLY IN THE LIGHT BLUE COLOURED CELLS.

Station Erection portion including Testing and Commissioning:

Sl No Name of the Equipment/Materials Unit Total Quantity

SE1 Power Transformer: 20MVA, 66/11kV TRANSFORMER. 66/11KV, Delta/Star, Dyn11, 3-Ph, 50Hz, Core Type, 2 Winding Delta/Star transformer, vector group DYn11 with OLTC ONAN/ONAF with fan control cubicle, RTCC Panel, first filling of Oil and 10% spare oil in non-returnable drums etc., and 2 Nos. of 11kV Insulated copper flats for each phase from LV side of transformer to cable at cable terminating structure with suitable support bracket and support insulators for LV side copper flat bus and 2 Nos. of Copper Flats from Neutral Terminal to the Earthmat through NCT and necessary Support Pin Insulators as per technical specification. Note: Copper Flats required for Power Transformers shall be supplied along with the Transformers as per Technical Specifications.The Bidder has to quote for complete scope of erection of transformer including moving the transformer from the point of unloading to the point of erection, assemblying the complete transformer, filtration of oil using filter set of the bidder to achieve the required insulation value as per I.E. specifications, erection of the complete transformer wiring of transformer, testing & commissioning etc., complete. Terminal connectors suitable for Drake/Moose ACSR on Primary side of the power transformer on 11kV and connectors for neutral sutiable for 2nos. of Copper flats as per technical specification. No 2

SE2 CIRCUIT BREAKER : SF-6 Circuit Breaker with terminal connector suitable for Moose ACSR conductor / 63mm Al. pipe with spring/semi-pneumatic/pneumatic type operating mechanism and mounting structure etc.,as per technical specification 72.5 kV, 2500 A, 40 KA Class SF6 CB- i)For 66kV Line No 3

SE3 ii)For 66/11kV Power transformer No 2

SE4 ISOLATORS : 66kV, 1250 A, 40kA double break manually operated isolators with solid core Cylindrical post insulator, terminal connector suitable for Drake ACSR conductor/ 63mm/75mm Al. pipe conductor, marshalling box etc., complete as per technical specification Note:Terminal Connectors for isolators shall be as follows i)Upright mounting type with Earth switch.LPH 4600mm Set 3

SE5 ii)Upright mounting type without Earth switch. LPH 6350mm. Set 6

SE6 11kV Isolators: 11kV isolator, Double break 400 A, 25KA capacity with rigid bi-metallic terminal connector suitable for coyote ACSR conductor.(Capacitor Bank) Set 4

SE7 11kV isolator, Single break 400A, 25KA capacity with Roaster Switch with bi-metallic terminal connector suitable for coyote ACSR Conductor. Set 11

SE8 CURRENT TRANSFORMER : Current transformers including marshalling boxes, Single phase,oil filled outdoor type with rigid bimetallic terminal connectors suitable for or Drake ACSR conductor / 63mm Al. pipe as per technical specifications. i)66kV class, 40KA, CT of ratio 800-400 / 1-1-1A for Tr.Line. Core-1:Dist/diff. Acc class PS, Vk-1400V at 800A, Rct-5ohm at 800/1A. Core-2:For metering : Accuracy 0.2s, Burden 10 VA Core-3:For backup protetion : Accuracy 5P20. Burden 30 VA No 6

SE9 ii)66 kV class, 40 KA, CT of ratio 400-200 / 1-1-1A for Tr. lines. Core-1: Vk-1600V at 400A, Rct 4ohm at 400/1A, Accuracy class PS- Dist/Dif Core-2: For metering : Accuracy 0.2s, Burden 10 VA Core-3: For backup protetion : Accuracy 5P20. Burden 30 VA No 3

SE10 ii)66 kV class, 40 KA, CT of ratio 200-100 / 1-1-1A for Transformer. Core-1: Vk-800V at 200A, Rct 2ohm at 200/1A, Accuracy class PS- Dist/Dif Core-2: For metering : Accuracy 0.2s, Burden 10 VA Core-3: For backup protetion : Accuracy 5P20. Burden 30 VA No 6

SE11 11kV class, 25 KA, NCT of ratio 1200-800/1-1-1A for REFR protection(of similar rating and ratio as that of Incomer of 11kV switchgear) with terminal connector suitable for 2 Nos of Copper flats as per technical specification. NOTE:1. For details refer Annexure-IIB. Technical Paramaters of current Transformers for type and rating attached at the end of this schedule. 2) All the Current transformers in each KV class shall be of One and the same make for interchangeability and reliability of performance. 3) The characteristics of 11kV NCT should be the same as that of the incomer CT of 11kV Switchgear 4) The Terminal connectors for 11kV NCT shall be suitable for 2 nos. of Copper flat as per technical specification. No 2

SE12 VOLTAGE TRANSFORMER : VOLTAGE TRANSFORMER Single phase, oil filled, outdoor type VT with rigid bimetallic terminal connector suitable for Drake ACSR Conductor with marshalling box etc., complete as per technical specification. Ratio: 66kV/sqrt(3)/110V/sqrt(3) - 110V/sqrt(3)-110V/sqrt(3) Core - 1 : 300 VA, Accuracy class 0.2. Metering Core - 2 : 200 VA, Accuracy class 3P. Protection Core - 3 : 50 VA, Accuracy class 3P. Open / delta No 3

SE13 SURGE ARRESTOR (Porcelain Housing) metal oxide, Gapless type, as per Technical Specification: i) 60 kV, 10KA Metal Oxide with surge counter Arrestor class : Discharge Class 3 (Station Medium Duty (SM)- for overhead lines No 9

SE14 ii)60 kV, 10KA Metal Oxide with surge counter Arrestor class : Discharge Class 3 (Station Medium Duty (SM))- for Transformer No 6

SE15 iii)9kV, 10KA class station class with connector and clamp No. 33

SE16 Control and Relay Panel: Simplex 110V DC compatible to SCADA complete as per technical specification Note: 1. All the C&R Panels and associated panels shall be of one and the same make for uniformity and interchangeability of Components. 2. The accuracy class of metering core of CTs and VTs and ETV meter of C&R panels shall be 0.2s accuracy class irrespective of what has been indicated else where in the bid document. 3. The electronic Tri-vector meter of 0.2 accuracy class with ABT & TOD features, DLMS protocol energy meter has to be provided both on HV and LV side of C&R Panel. i)For Power transformer 66/11 kV No. 2

SE17 ii)For 66kV Transmission line No. 3

Station Structures : 66kV Side station structure fabricated out of galvanized mild steel including Bolts and Nuts as per specifications. i) Station towers fabricated out of galvanised mild steel(verticals 1T1) (1.054t/tower) (0.9860 t per tower for structure+0.0680 t per tower for Bolt & Nuts per structure) t 4/4.216

ii) Station Beams fabricated out of galvanised mild steel. Beam type 1B1 with peak.(8.2 mtr bay width)( 0.553t/tower) (0.5210 t per tower for structure+0.0320 t per tower for Bolt & Nuts per structure) t 3/1.659

iii) Tubular type Lighting / lighting Mast (approx wt. 2.812 t) (2.6714t per tower +0.1406t for Bolt & Nuts per structure) t 1/2.812

iv) Street lighting lattice type structure along with GI pipe for fixing of LED lamp (0.182 MT )-8.5 mtr height(0.182t per structure+0.0091 t for Bolt & Nuts per structure) t 12/2.2932

MOUNTING STRUCTURES including Bolts and Nuts as per specifications. i) Isolators Live point height 4600mm. (0.752 t)(0.7260t per structure+0.0260t for Bolt &Nuts per structure) t 3/2.256

ii) Isolators Live point height 6350mm. (0.982t)(0.9550t per structure+0.0270 t for Bolts & Nuts per structure) t 6/5.892

iii) Current transformer.66kV (0.158 MT)(0.1460t per structure+0.0120t for Bolts & Nuts per structure) t 15/2.37

iv)11 kV NCT (0.157 t)(0.1460t per structure+0.0110t for Bolts & Nuts per structure) t 2/0.314

v) Voltage transformer (0.148 t per structure)(0.1370t per structure+0.0110t for Bolts & Nuts per structure) t 3/0.444

vi) Lightening arrestors (0.116 t per structure)(0.1050t per structure+0.0110t for Bolts & Nuts per structure) t 15/1.74

vii) Pedestal insulators (0.141 t per structure) (0.129t per structure+0.012t for Bolts & Nuts per structure) t 12/1.68

viii) For High pedestal insulators (0.150 t per structure)(0.1340t per structure+0.0160 t for Bolts & Nuts per structure) t 6/0.9

ix) 11KV Cable Terminating Structure for LV Side of Transformer(0.072 t Per Structure)(0.0690t per structure+0.0030 t for Bolts & Nuts per structure) t 2/0.144

x) 11KV GOS/Cable Terminating Structure for 11KV Capacitor Bank(0.158 t per structure)(0.1501t per structure+0.0079t for Bolts & Nuts per structure) t 4/0.632

SE18 Total Weight of Mild Steel of Station structures and Mounting Structures + Weight of Bolts & nuts. Note :- Rate to be quoted on per tonne basis t 27.3522

SE19 11 kV ODS and take off structure : Double pole structure with 9.5 Mts. RCC poles,300Kg WL and with provision for fixing 11 kV 400 A Roaster single break isolators & provision for fixing 9kV lightning arrestors complete set with wiring materials (including DP Set, Pin Insulator, Pin for Insulator and H frame) Set 11

SE20 BUS BAR FORMATION : Formation of main Bus with Drake Nos 2

SE21 Rigid Bus with Taps & Clamps : 66kV side: i) Aluminium pipe conforming to 6340WP of IS - 5082 / 1969 (BS I600-Sch. 40) of following nominal diameter a) 75mm Mtr 60

SE22 b) 63mm size connecting isolator to vertical tap Mtr 108

SE23 INSULATORS: Post insulators- Cylindrical solid core as per technical Specification Solid Core Bus Post Insulator 66kV class, 1Unit/stack. Nos 18

SE24 Auxiliary Transformer: Station Auxiliary Transformer with Copper winding & oil, outdoor type, 100 kVA, 11kV/433 V, 3 Ph, Vector group Dyn11, off load tap changer (with 5 taps) with step voltage of 2.5% as per technical specification. No. 1

SE25 Double Pole Structure along with 9.5 mtr RCC pole, DP Set, H Frame, 11kV 400A Double break isolator and 9kV, 10kA surge arrestor (3 Nos), HG Fuse Unit,Angle for fixing HG fuse unit( pole clamps bolt & nuts etc) PIN insulator, PIN for insulator, LT Distribution Box and Tri vector Meter, & complete set for auxiliary Transformer etc set 1

SE26 A) LTAC Panel (Indoor), 415 V as per technical specification comprising of voltmeter and ammeter,1 I/C MCCB 200A + 2 nos. 3 Phase 63A O/G SFU, + 2 nos. 3 Phase 32A O/G SFU 100A + 14 O/G SFU, 6 nos. 3 Phase 16A SFU etc., complete as per technical specification. No 1

SE27 B) A.C. Distribution Box (Outdoor) : AC Distribution Box Single front (Outdoor type) 6 Terminal, one I/C of 100A MCCB 20kA + 6 O/G MCB 16A + 1 O/G of 100A, HRC fuse, complete as per technical specification. No 1

SE28 LT Power Cable:1.1 kV Class Armoured Aluminium Cable with glands/lugs/ferrules : a) 1.1 kV PVC Insulated 4X95 sq.mm Aluminium cable 4 core with glands / lugs / ferrules Mtr 300

SE29 b) 1.1 kV PVC Insulated 4X25 sq.mm Aluminium cable 4 core with glands / lugs / ferrules Mtr 300

SE30 c) 1.1 kV PVC Insulated 4X10sq.mm Aluminium cable 4 core with glands / lugs / ferrules Mtr 300

SE31 STATION BATTERY: 110V, 200AH, Battery set Plante/Grid/Nickel Cadmium Type as per technical specification Set 1

SE32 BATTERY CHARGER : Battery charger suitable for 110V, 200 AH, Battery set Plante/Grid/Nickel Cadmium Type with float cum booster type battery charger as per technical specification. Set 1

SE33 DC Distribution Panel (Indoor) as per technical specification comprising of earth fault indicator, indication circuit for AC mains failure, 1 no. 100A SFU for I/C + 12 nos. 32A SFU for O/G, complete as per technical specification. Nos 1

SE34 Copper control cables: 1.1kV class PVC insulated Copper Control Cable with Lugs / Ferrules, Glands as per specificaions i) 19 Core x 2.5 Sq.mm. Mtr 2000

SE35 ii)10 Core x 2.5 Sq.mm. Mtr 2000

SE36 iii) 4 Core x 6.0 Sq.mm. Mtr 2000

SE37 iv) 4 Core x 2.5 Sq.mm. Mtr 1000

SE38 v) 2 Core x 2.5 Sq.mm. Mtr 300

SE39 vi) 2 Core x 6 Sq.mm. (Yard Lighting-1280 Mtr included) Mtr 2480

SE40 11kV Switchgear:11kV, 25KA, 500 MVA MCVCB switchgear 1600 A for incomer and 1250 A for feeders (SCADA Compatable) Out door type comprising of 2IC+12F+1BC+4CB+1AP (Remote annunciation cum Control panel) with CTs & PTs etc.,complete as per technical specification Note: 1. The switchgear for capacitor bank shall have necessary Over voltage / Under voltage /Timer/ Circulating current relays and other protection relays as per specification 2. The Remote Announciation cum Control panel is Simplex type. 3.The Electronic Trivector meters with 0.2s accuracy class with ABT & TOD features & DLMS ICS compliant features has to provided. 4.The Switchgear will be supplied by KPTCL and the Bidder has to quote for complete scope of erection of Switchgear including moving the Switchgear from the point of unloading to the point of erection, erection of the complete Switchgear, wiring of Switchgear, testing & commissioning etc., complete. Set (KPTCL Supply) 1

SE41 11kV, XLPE Insulated UG Cable as per Technical Specification a) 11kV Single Core, 1000 sq.mm Aluminium cable To be run from 66/11 kV transformers to 11kV switchgear). Mtr 550

SE42 b) 3X240 sq.mm Aluminium cable (To be run from 11 kV switchgear to 11kV take off DP structure) Mtr 500

SE43 c)3X95 Sq.mm Aluminium Cable( To be Run from 11kV Switchgear to Auxiliary Transformer) Mtr 50

SE44 d(i)Cable Termination kits suitable for 95Sq. mm 3 Core as per techincal specification. Indoor type Nos 1

SE45 d(ii)Cable Termination kits suitable for 95Sq. mm 3 Core as per techincal specification. Outdoor type Nos 1

SE46 e(i)Cable Termination kits suitable for 240Sq. mm 3 Core as per techincal specification. Indoor type Nos 15

SE47 e(ii) Cable Termination kits suitable for 240Sq. mm 3 Core as per techincal specification. Outdoor type Nos 15

SE48 f(i) Cable Termination kits suitable for 1000sq mm Single Core as per techincal specification. Indoor type Nos 14

SE49 f(ii)Cable Termination kits suitable for 1000 sq mm Single Core as per techincal specification. Outdoor type Nos 14

SE50 Equipments required for establing SCADA Communication as per KPTCL Specification Note:1. Satellite communication required will be arranged by SLDC a. Remote Terminal Unit (RTU) 64 (I/O) Port Nos 1

SE51 b.Data Concentrator Unit (DCU) Nos 1

SE52 c.2kVA online UPS (230V AC 1 phase 50Hz) Nos 1

SE53 d. Integration of RTU, DCU & UPS with field equipments Nos 1

SE54 SCADA Cables: i)Current Cables - copper core with c/s 4.0sqmm multistrand 4 core Mtr 40

SE55 ii)Voltage Cables-Copper core with c/s 2.5sqmm multistrand 4core Mtr 20

SE56 iii) Signal cables- armoured copper core with c/s 0.5sqmm multistrand 10core Mtr 500

SE57 iv)Control cables - copper core with c/s 1.5sqmm multistrand 10core Mtr 160

SE58 v)Cables- Copper core with c/s 4.0sqmm multistrand 3core for AC input to UPS and UPS to RTU, conforming to KPTCL specfications. Mtr 15

SE59 vi) Cables-1C x 32 Sq mm multistrand for battery conforming to KPTCL specification Mtr 30

SE60 EarthMat Formation: Supplying and laying MS.Flat 75 x 12 mm flat welding and applying ACB paint to welded portion and covering with sodium bentonite clay as per the drawing/ standard specification and consolidation Rmtr 8586

SE61 Supplying & Grounding of equipments with 75 x 12 mm G I flat and connecting equipments to the earth mat/ground pit each point of earthing with all formation of works like bending, twisting, drilling of holes and connecting by welding (inclusive of all T&P and consumables) to the earthmat/ ground pit/point of earth connection Rmtr 1880

SE62 Supplying & Providing 40mm dia, MS round rod 1.075mtr. long Earthmat Spike including bending top 50 mm , overlap, flatening and making spike edge at one end driving into the earth below the ground level and welding the rod with ground mat No 176

SE63 Supplying & Providing C.I. Pipe of 100mm ID 13mm thick 2.75 mtr. long with 2 part GI Flat 50x6mm clamp welded allround the pipe etc., including cost of excavation with Sodium Bentonite treatment (all materials supplied by contractor) No 50

SE64 Supplying and fixing 450mm dia x 450mm height 1.5" to 2" Hume pipe collars for earth pits including transportation all lead & lifts etc. No 50

SE65 Providing deep bore earthing:-Sinking bore of 150 mm clear dia using fast rig including fixing of 40 mm dia MS Rod, including jointing the pipes as per KPTCL standard and providing sodium bentonite treatment in the annular space, including transportation of rig and other supporting vehicles etc., Deepbore Electrodes of 5Mtr Length, 10 Mtr Spacing, 40 mm dia i)Drilling of 150mm dia bore Rmtr 175

SE66 ii)40mm dia MS rod (5 Mtr Length) Rmtr 175

SE67 iii)Bentonite clay Kg 500

SE68 iv)Cost of the GI flat for joining two rods by welding to obtain continous length Joints 35

1. Any clarifications / hard copy of drawings can be obtained from the office of the Chief Engineer Electricity, Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore.

2. Released materials shall be transported to the nearest Major Works Store of KPTCL without any additional cost as per the directions of the Engineer in charge of the work.

3. The Erection charges shall include transportaion to site, loading and unloading.

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3A(ii) - Price Breakup for - Terminal bay Erection portion including Testing and Commissioning.

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidder's Name & Address alongwith GSTIN no. :

The Chief Engineer, Electricity, Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore-560009.

BIDDERS SHALL FILL ONLY IN THE LIGHT BLUE COLOURED CELLS.

Station Erection portion including Testing and Commissioning:

Sl No Name of the Equipment/Materials Unit Total Quantity

TBE1 CIRCUIT BREAKER : SF-6 Circuit Breaker with terminal connector suitable for Moose ACSR conductor / 63mm Al. pipe with spring/semi-pneumatic/pneumatic type operating mechanism and mounting structure etc.,as per technical specification 72.5 kV, 2500 A, 40 KA Class SF6 CB- i)For 66kV Line No 1

TBE2 ISOLATORS : 66kV, 1250 A, 40kA double break electrically & manually operated isolators with solid core Cylindrical post insulator, terminal connector suitable for Drake ACSR conductor/ 63mm/75mm Al. pipe conductor, marshalling box etc., complete as per technical specification Note:Terminal Connectors for isolators shall be as follows For Terminal Bay :Rigid Type suitable for Drake ACSR -48Nos Flexible Type suitable for 63mm Al Pipe-12Nos i)Upright mounting type with manually operated Earth switch.LPH 4250mm Set 1

TBE3 ii)Upright mounting type without Earth switch.LPH 5500mm Set 2

TBE4 iii)Upright mounting type without Earth switch. LPH 4250mm. Set 1

TBE5 iii)Underhung mounting type without Earth switch. Set 1

TBE6 ii)66 kV class, 40 KA, CT of ratio 400-200 / 1-1-1A for Tr. lines. Core-1: Vk-1600V at 400A, Rct 4ohm at 400/1A, Accuracy class PS- Dist/Dif Core-2: For metering : Accuracy 0.2s, Burden 10 VA Core-3: For backup protetion : Accuracy 5P20. Burden 30 VA No 9

TBE7 SURGE ARRESTOR (Porcelain Housing) metal oxide, Gapless type, as per Technical Specification: i) 60 kV, 10KA Metal Oxide with surge counter Arrestor class : Discharge Class 3 (Station Medium Duty (SM)- for overhead lines No 3

TBE8 Control and Relay Panel: 66kV line- Type 6L (as per annexure RPP4- SAS ) with Annunciator and control switches for CB & isolators No. 1

Station Structures : 66kV Side station structure fabricated out of galvanized mild steel including Bolts and Nuts as per specifications. i) Station towers fabricated out of galvanised mild steel(verticals 1T1) (1.054t/tower) (0.9860 t per tower for structure+0.0680 t per tower for Bolt & Nuts per structure) t 1/0.912

ii) Station Beams fabricated out of galvanised mild steel. Beam type 1B1 with peak.(8.2 mtr bay width)( 0.553t/tower) (0.5210 t per tower for structure+0.0320 t per tower for Bolt & Nuts per structure) t 1/0.594

iii) Tubular type Lighting / lighting Mast (approx wt. 2.812 t) (2.6714t per tower +0.1406t for Bolt & Nuts per structure) t 1/0.448

iv) Street lighting lattice type structure along with GI pipe for fixing of LED lamp (0.182 MT )-8.5 mtr height(0.182t per structure+0.0091 t for Bolt & Nuts per structure) t 0

MOUNTING STRUCTURES including Bolts and Nuts as per specifications. i) Isolators Live point height 4600mm. (0.752 t)(0.7260t per structure+0.0260t for Bolt &Nuts per structure) t 2/0.95

ii) Isolators Live point height 6350mm. (0.982t)(0.9550t per structure+0.0270 t for Bolts & Nuts per structure) t 2/1.252

iii) Current transformer.66kV (0.158 MT)(0.1460t per structure+0.0120t for Bolts & Nuts per structure) t 3/0.453

iv)11 kV NCT (0.157 t)(0.1460t per structure+0.0110t for Bolts & Nuts per structure) t 3/0.441

v) Voltage transformer (0.148 t per structure)(0.1370t per structure+0.0110t for Bolts & Nuts per structure) t 6/1.038

vi) Lightening arrestors (0.116 t per structure)(0.1050t per structure+0.0110t for Bolts & Nuts per structure) t 3/0.654

vii) Pedestal insulators (0.141 t per structure) (0.129t per structure+0.012t for Bolts & Nuts per structure) t 0/0

viii) For High pedestal insulators (0.150 t per structure)(0.1340t per structure+0.0160 t for Bolts & Nuts per structure) t 0/0

ix) 11KV Cable Terminating Structure for LV Side of Transformer(0.072 t Per Structure)(0.0690t per structure+0.0030 t for Bolts & Nuts per structure) t 0/0

x) 11KV GOS/Cable Terminating Structure for 11KV Capacitor Bank(0.158 t per structure)(0.1501t per structure+0.0079t for Bolts & Nuts per structure) t 0/0

TBE9 Total Weight of Mild Steel of Station structures and Mounting Structures + Weight of Bolts & nuts. Note :- Rate to be quoted on per tonne basis t 6.742

TBE10 BUS BAR FORMATION : Formation of main Bus with Drake Nos 1

TBE11 b) 50mm size connecting isolator to vertical tap Mtr 54

TBE12 INSULATORS: Post insulators- Cylindrical solid core as per technical Specification Solid Core Bus Post Insulator 66kV class, 1Unit/stack. Nos 3

TBE13 B) A.C. Distribution Box (Outdoor) : AC Distribution Box Single front (Outdoor type) 6 Terminal, one I/C of 100A MCCB 20kA + 6 O/G MCB 16A + 1 O/G of 100A, HRC fuse, complete as per technical specification. No 1

TBE14 c) 1.1 kV PVC Insulated 70sq.mm Aluminium cable 3.5 core with glands / lugs / ferrules Mtr 1500

TBE15 Copper control cables: 1.1kV class PVC insulated Copper Control Cable with Lugs / Ferrules, Glands as per specificaions i) 19 Core x 2.5 Sq.mm. Mtr 3000

TBE16 ii)14 Core x 2.5 Sq.mm. Mtr 3000

TBE17 ii)10 Core x 2.5 Sq.mm. Mtr 2000

TBE18 ii)7 Core x 2.5 Sq.mm. Mtr 2000

TBE19 iii) 4 Core x 6.0 Sq.mm. Mtr 3000

TBE20 iv) 4 Core x 2.5 Sq.mm. Mtr 2000

TBE21 v) 4 Core x 4 Sq.mm. Mtr 2000

TBE22 NEW BAY INTEGRATION TO SCADA 8 Channel 220/110 V Opto Coupler Nos 1

TBE23 Multi Function Transducer (MFT) Nos 1

TBE24 SCADA Cables: i)Current Cables - copper core with c/s 4.0sqmm multistrand 4 core Mtr 40

TBE25 ii)Voltage Cables-Copper core with c/s 2.5sqmm multistrand 4core Mtr 20

TBE26 iii) Signal cables- armoured copper core with c/s 0.5sqmm multistrand 10core Mtr 100

TBE27 iv)Control cables - copper core with c/s 1.5sqmm multistrand 10core Mtr 100

TBE28 Configuration of RTU and Engineering along with validation of data at SLDC Nos 1

TBE29 Supplying & Grounding of equipments with 75 x 12 mm G I flat and connecting equipments to the earth mat/ground pit each point of earthing with all formation of works like bending, twisting, drilling of holes and connecting by welding (inclusive of all T&P and consumables) to the earthmat/ ground pit/point of earth connection Rmtr 600

TBE30 Supplying & Providing C.I. Pipe of 100mm ID 13mm thick 2.75 mtr. long with 2 part GI Flat 50x6mm clamp welded allround the pipe etc., including cost of excavation with Sodium Bentonite treatment (all materials supplied by contractor) No 6

TBE31 Supplying and fixing 450mm dia x 450mm height 1.5" to 2" Hume pipe collars for earth pits including transportation all lead & lifts etc. No 6

TBE32 Releasing & Reerection of Existing 66kV PTs Nos 6

TBE33 Releasing & Re-erection of Existing 66kV Isolator height of 5500MM without Earthswitch. Nos 2

TBE34 Releasing & Reerection of Existing 66kV CTs (Note: for 66kV Chalkere Bay) Nos 3

TBE35 Dismantling Portion at 220/66/11kV Chitradurga S/s: Note : 1) The Released materials shall be transported to the nearest Stores of KPTCL. 2)The rates quoted for releasing/dismantling shall also include the charges for loading, transportation to KPTCL stores and unloading. 3) Before Commencing the dismantling Work, Items wise Inventory of the Equipments / Materials to be Dismantled are to be prepared jointly with the Engineer In-Charge, which is to be got approved by the respective Chief Engineer Electricity, Transmission Zone. 4) Quantity mentioned here is indicative payment will be made as per actuals i)Dismantling of existing 66kV PT Structure ( 0.1557 MT) Per Structure (6Nos) t 0.9342

TBE36 ii) Dismantling of existing 66kV Isolator structure ( 0.5634 MT) Per Structure (2 Nos) t 1.1268

TBE37 iii) Dismantling of existing 66kV CT (3Nos) t 6

1. Any clarifications / hard copy of drawings can be obtained from the office of the Chief Engineer Electricity, Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore.

2. Released materials shall be transported to the nearest Major Works Store of KPTCL without any additional cost as per the directions of the Engineer in charge of the work.

3. The Erection charges shall include transportaion to site, loading and unloading.

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3BI(i) - Price Breakup for - Line Supply portion

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer, Electricity, Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore-560009.

BIDDERS SHALL FILL ONLY IN THE LIGHT BLUE COLOURED CELLS.

LINE SUPPLY PORTION :

Sl.No Description Unit Quantity Unit wt of Tower in t Total wt of Tower in t Country of origin Indicate whether "Own manufactured Item" or "Bought Out Item"

Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms Total Quantity HT MS B&N HT MS B&N

1 I) Fabrication, Prototype Inspection and supply of galvanised 110kV DC Transmission Line Towers. Note :- Rate to be quoted on per tonne basis Tower type 110KV DC Towers (Design Code: KPTCL-1D-AQUS) A) DC 'A' Type Tower Normal Tower Type DA' No/t 11 11 0.9430 1.9110 0.1354 10.37256 21.0210 1.4900

3M Extension to 'DA' Type Tower No/t 8 8 0.1694 0.3329 0.0203 1.35552 2.6630 0.1622

6M Extension to 'DA' Type Tower No/t 3 3 0.36624 0.6898 0.0402 1.09872 2.0694 0.1206

d) Stubs for Tower Type 'DA' No/t 11 11 0.1470 0.0032 1.617 0.0000 0.0356

B) DC 'B Type Tower Normal Tower Type DB' No/t 6 6 1.5879 2.0587 0.1814 9.5274 12.3521 1.0881

3M Extension to 'DB' Type Tower No/t 5 5 0.2571 0.4351 0.0281 1.2856 2.1754 0.1404

6M Extension to 'DB' Type Tower No/t 1 1 0.5940 0.8499 0.0559 0.594 0.8499 0.0559

Stubs for 'DB' Type Tower No/t 6 6 0.2104 0.0049 1.26264 0.0000 0.0292

C) TOWER TYPE DC 'D' a) Normal Tower Type 'DD' No/t 2 2 2.9699 1.6490 0.2041 5.93978 3.2980 0.4082

b) 3M Extension to Tower Type 'DD' No/t 2 2 0.4142 0.4636 0.0321 0.82848 0.9273 0.0643

c) 6M Extension to Tower Type 'DD' No/t 0 0 0.8618 0.9827 0.0645 0 0.0000 0.0000

f) Stub for Normal towers +3mtr towers, +6mtr towers No/t 2 2 0.3016 0.0069 0.60312 0.0000 0.0137

II) Fabrication, Protype Inspection and Supply of MC Towers (Design Code:KPTCL-1M-CPRI) A) TOWER TYPE MD a) Normal Tower Type No/t 3 3 17.2800 0.5120 0 51.8400 1.5360

b)3M Extension to Tower Type No/t 2 2 2.0130 0.0500 0 4.0260 0.1000

b)6M Extension to Tower Type No/t 1 1 3.7500 0.1050 0 3.7500 0.1050

c) Stubs for Tower Type No/t 3 3 1.039 0 3.1170 0.0000

Strengthning 3 No cross arm in each of the 2 Nos of existing towers at Loc No 34 & 35 located near the Aquaduct (2 t additional per tower considered) No/t 2 2 0.0000 2 0.0500 0 4.0000 0.1000

LS1 Grand Total weight of Tower parts- High Tensile Steel 110Kv Note:Rate to be quoted on per tonne Basis t 34.4848 34.4848 34.4848

LS2 Grand Total weight of Tower parts- Mild Steel Note:(i) Rate to be quoted on per t Basis. t 112.0891 112.0891 112.0891

LS3 Grand Total weight of Bolts & Nuts Note:(i) Rate to be quoted on per t Basis t 5.4491 5.4491 5.4491

LS4 Tower Accessories 1.Number Plates Nos 22 22

LS5 2.Danger Boards Nos 22 22

LS6 3.Circuit Plate Set 126 126

LS7 4.Phase Plate (set of 3 Nos) Nos 126 126

LS8 5.Earth bond of 450mm Long Nos 16 16

LS9 6.Earth bond of 300mm Long Nos 11 11

LS10 High Performance Conductor for new Transmission Lines with new Towers/Supports-as per Technical Specifications. Km 30.1455 30.1455

LS11 High Performance Conductor for existing Towers/Supports-as per Technical Specifications. Km 39.2440 39.2440

LS12 Coyote ACSR Conductor Km 0.6395 0.6395

LS13 Ground wire 7/3.15mm Ground Wire Km 5.2171 5.2171

LS14 I)Insulator Strings with Arcing Horns for HPC On existing towers (from 220kV station,Chitradurga to Location No:41) for existing towers as per technical specifications NOTE: All the Insulator strings quoted by the bidder shall be of the same type i.e. all the Insulator strings shall be of Disc Insulators type OR all the Insulator strings shall be of Polymeric Composite Insulators type OR all the Insulator strings shall be of Long rod insulator. Bidder shall quote either for Disc Insulators type OR for Composite Insulators type OR for Long rod insulator and not for all the types. A. Tension insulator strings consisting of any one of the following: a. Insulator string consisting of 1X5nos. of 90kN Disc insulators Or b. Porcelain long rod insulator string equivalent to 1x5nos. of 90kN Disc insulators Or c. single unit of 66kV 90kN Silicon Rubber composite insulators equivalent to 1X5nos. of 90kN Disc insulators strings 462 462

LS15 INSULATOR STRINGS : B.Suspension insulator strings consisting of any one of the following: a. Insulator string consisting of 1X4nos. of 90kN Disc insulators Or b. Porcelain long rod insulator string equivalent to 1x4nos. of 90kN Disc insulators Or c. single unit of 66kV 90kN Silicon Rubber composite insulators equivalent to 1X4nos. of 90kN Disc insulators strings 90 90

LS16 I)Insulator Strings with Arcing Horns for HPC On New towers (from Location No: 42 to proposed 66/11kV sub station,Belaghatta for new towers ) NOTE: All the Insulator strings quoted by the bidder shall be of the same type i.e. all the Insulator strings shall be of Disc Insulators type OR all the Insulator strings shall be of Polymeric Composite Insulators type OR all the Insulator strings shall be of Long rod insulator. Bidder shall quote either for Disc Insulators type OR for Composite Insulators type OR for Long rod insulator and not for all the types. A. Tension insulator strings consisting of any one of the following: a. Insulator string consisting of 1X8nos. of 90kN Disc insulators Or b. Porcelain long rod insulator string equivalent to 1x8nos. of 90kN Disc insulators Or c. single unit of 110kV 90kN Silicon Rubber composite insulators equivalent to 1X8nos. of 90kN Disc insulators strings 150 150

LS17 INSULATOR STRINGS : B.Suspension insulator strings consisting of any one of the following: a. Insulator string consisting of 1X7nos. of 90kN Disc insulators Or b. Porcelain long rod insulator string equivalent to 1x7nos. of 90kN Disc insulators Or c. single unit of 110kV 90kN Silicon Rubber composite insulators equivalent to 1X7nos. of 90kN Disc insulators strings 66 66

LS18 I)Insulator Strings with Arcing Horns for Coyote NOTE: All the Insulator strings quoted by the bidder shall be of the same type i.e. all the Insulator strings shall be of Disc Insulators type OR all the Insulator strings shall be of Polymeric Composite Insulators type OR all the Insulator strings shall be of Long rod insulator. Bidder shall quote either for Disc Insulators type OR for Composite Insulators type OR for Long rod insulator and not for all the types. A. Tension insulator strings consisting of any one of the following: a. Insulator string consisting of 1X8nos. of 90kN Disc insulators Or b. Porcelain long rod insulator string equivalent to 1x8nos. of 90kN Disc insulators Or c. single unit of 110kV 90kN Silicon Rubber composite insulators equivalent to 1X8nos. of 90kN Disc insulators strings 24 24

LS19 Insulator Hardware for HPC on Existing Towers A.Single Tension Clamp with hardware and arcing hornto suit HPC Existing Tower Set 198 198

LS20 B.Double Tension clamp with hard ware and arcing horn to suit HPC Existing Tower Set 132 132

LS21 C. Single suspension Clamp with hardware and arcing horn to suit HPC Existing Tower Set 78 78

LS22 D. Double suspension Clamp with hardware and arcing horn to suit HPC Existing Tower Set 6 6

LS23 Dead End clamp Nos 330 330

LS24 Insulator Hardware for HPC on New Towers A.Single Tension Clamp with hardware and arcing horn to suit HPC New Tower Set 126 126

LS25 B.Double Tension clamp with hard ware and arcing horn to suit HPC New Tower Set 12 12

LS26 C. Single suspension Clamp with hardware and arcing horn to suit HPC New Tower Set 66 66

LS27 Dead End clamp Nos 138 138

LS28 Insulator Hardwares & Clamps suitable for Coyote ACSR Conductor as per Technical Specification: i) Single Tension Clamp with hardware and arcing horn to suit Coyote ACSR. Set 24 24

LS29 Accessories for HPC for new transmission lines with New Tower. 1.M S C Joints for HPC New Tower Nos 30 30

LS30 2.Repair sleeves for HPC New Tower Nos 30 30

LS31 3.Vibration dampers for HPC New Tower Nos 264 264

LS32 4.T Clamps for HPC New Tower Nos 66 66

LS33 Accessories for HPC for new transmission lines with Existing Tower. 1.M S C Joints for HPC Existing Tower Nos 38 38

LS34 2.Repair sleeves for HPC Existing Tower Nos 38 38

LS35 T Clamps Nos 84 84

LS36 3.Vibration dampers for HPC Existing Tower Nos 492 492

LS37 Accessories for Coyote ACSR : MSC Joints Nos 1 1

LS38 Repair sleeves Nos 1 1

LS39 P G Clamps Nos 24 24

LS40 Vibration dampers Nos 21 21

LS41 Accessories for Earthwire: 1.M S C Joints for Earth Conductor Nos 5 5

LS42 2.Repair sleeves for Earth Conductor Nos 5 5

LS43 3. Compression type Tension Clamp Nos 30 30

LS44 4. Bolted type Suspension Clamp Nos 11 11

NOTE: 1. Any clarifications / hard copy of drawings can be obtained from the office of the Chief Engineer Electricity, Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore.

2. Spacers shall be provided wherever necessary and no extra charges is payable on account of the same by KPTCL.

3. Supply of equipment/materials shall include transportation to the site, loading and unloading.

4. The Bidders shall start the line work from both the ends simultaneously by deploying more number of gangs as the ‘ROW’ issues which may crop-up can be addressed in parallel on both segments. The bidders shall take note of the same before quoting.

5. The Bidder shall take necessary action to ensure that all the materials supplied shall be properly housed to ensure satisfactory commissioning.

6. The prices for all the materials shall be quoted in the Percentage rate finanacial bid.

7. The Bidder shall clearly indicate whether the materials/equipments are “Own manufactured” or “Bought out item”.

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 3BI(ii) - Price Breakup for -Line Erection portion including Dismantling

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidder's Name & Address alongwith GSTIN no. :

The Chief Engineer, Electricity, Tendering & Procurement, KPTCL, 9th Floor, Indhavana Bhavan, A.R Circle, Bangalore- 560009.

BIDDERS SHALL FILL ONLY IN THE LIGHT BLUE COLOURED CELLS.

LINE ERECTION PORTION INCLUDING DISMANTLING:

Sl.No Name of the Equipment/Mataerials Unit Total Quantity to be Errected

LE1 Check survey to be conducted during construction stage: Conducting detailed check survey along the approved route duly following the route alignment, GPS Co-ordinates, submission of detailed line schedule, tower schedule, land schedule and comparing the same with respect to detailed survey report, bringing out the differences if any. Submission of contour maps for undulated/hilly tower. The work also includes marking corridor width in the field and computing the quantum of benching and revetment, preparation of detailed land schedule along the corridor on the digitized Revenue village maps indicating the Sy. Nos. falling within the corridor for the purpose of estimation of the land compensation, submission of detailed consolidated hard copy of reports of check survey in 6 sets along with soft copy for approval in all types of terrain per km. 66kV Line &Plain Terrain Km 11.394

LE2 Conducting drone survey of transmission Lines for collection of data along with Aerial inspection of EHV Line corridor using LIDAR method for measurements of vertical, horizontal and ground clearances of the LT/HT/EHV/PandT lines, major road/railway/river crossing, buildings, vegetation’s, etc., which is found to cross or running in parallel with the KPTCL existing EHV lines and sag measurements and other works. The rates include to collect details such as, i Vegetation growth close to conductor along the width of corridor with measurements ii Building/construction violation along the corridor with measurements iii Clearance measurement of Roads/Railways. River crossings iv Clearance measurement of EHV/Power line crossings (up and down) v Clearance measurements of tower elements (Hang point & Ground point measurement) vi Sag measurement of each span of the line all phases vii Location of tower (GPS coordinates), type of tower, height of tower, span length and conductor type viii Angle of deviation of tower ix Submission of detailed consolidated final report for surveying work done appending all the above details including all relevant information collected during survey certificates of the instruments used for the work, photos/videos taken at site and submitting soft copies and hard copy of all documents & reports in 3 sets. Note: 1) The minimum requirement of LiDAR camera is as follows point cloud with RGB mapping Accuracy of +/-25cm ability to gather minimum of 75 points/sqmtr. 2) Minimum 1 km length shall be considered for payment. 3) Patrolling shall at least cover the minimum corridor area as per the voltage classes. Km 11.394

LE3 Stringing of Conductor without allowing the conductor to touch the ground and without damaging the conductor Paving out conductor from anchor to anchor normally spaced at 5 spans with 4 tangent towers in between, including providing stays at each anchor points and jointing of conductors, hoisting and fixing of insulator string, armour rods, vibration dampers, including the cost of T&P materials like comealong, wire ropes, pulley, rollers, suspension clamps, compression jointing machines with bits, drum stands, manila ropes, truckker and jeep etc.,Installing insulator strings complete with necessary Hardwares, Installing and stringing of conductor/Earthwire including fixing of their accessories, etc., a. High Performance Conductor with new Towers/Supports-as per Technical Specifications. Km 30.1455

LE4 High Performance Conductor for existing Towers/Supports-as per Technical Specifications. Km 39.244

LE5 Coyote ACSR Conductor Km 0.6395

LE6 b. Earth wire-7/3.15mm Km 5.2171

LE7 Erection of 110kV Transmision Line Towers (including tower accessories,etc., except GI angle with Barbed wire & Grounding materials) Note: (i)The Bidders are required to quote the rates taking in to consideration of the charges for sorting of towers, loading, unloading, stub setting, aligning,fixing of tower accessories,etc., except GI angle with Barbed wire & Grounding materials, dismantling & transportation of templates from one location to another and tack welding. (ii)Rate to be quoted on per t Basis. (iii) Refer Line Supply Portion for detail Breakup qty. t 152.02296

LE8 Tower accessories: a. Supplying and fixing GI angle 45 x 45 X 5mm, 1Mtr length with cleats, bolts nuts as per specification and fixing above 0.5mtr length each at inner and outer surface of tower to facilitate running of barbed wire Set 22

LE9 b. Supplying and fixing Barbed wire as per Specification m 3650

LE10 c.Grounding of towers including cost of 40 mm dia 2.5 mm thick,class 'C' G.I. Pipe of 3 metres length as per specification with 50 X 6 mm GI Flats 3 metrelong, salt, charcoal, including excavation charges Set 22

LE11 Dismantling of existing 66 kV SA type Tower ( 0.8 MT) Per Tower (16Nos) t 12.80

LE12 Dismantling of existing 66 kV AP type Tower ( 1.1 MT) Per Tower (3 Nos) Note : 1) The Released materials shall be transported to the nearest Stores of KPTCL. 2)The rates quoted for releasing/dismantling shall also include the charges for loading, transportation to KPTCL stores and unloading. 3) Before Commencing the dismantling Work, Items wise Inventory of the Equipments / Materials to be Dismantled are to be prepared jointly with the Engineer In-Charge, which is to be got approved by the respective Chief Engineer Electricity, Transmission Zone. 4) Quantity mentioned here is indicative payment will be made as per actuals t 3.3

LE13 Releasing Coyote Conductor (33774 Mtrs) Km 33.774

LE14 Releasing Ground wire (5007 Mtrs) Km 5.007

NOTE: 1. Any clarifications / hard copy of drawings can be obtained from the office of the Chief Engineer Electricity,Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore.

2. The Erection charges shall include transportaion to site, loading and unloading.

3. Bidders shall start the line work from both the ends simultaneously by deploying more number of gangs as the ‘ROW’ issues which may crop-up can be addressed in parallel on both segments. The bidders shall take note of the same before quoting.

4. The charges for erection shall be quoted in the Percentage rate finanacial bid.

5. Released materials shall be transported to the nearest KPTCL Projects Division Stores without any additional cost as per the directions of the Engineer in charge of the work.

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

a) Establishing 2X20 MVA, 66/11 kV Sub-Station at Belaghatta in Chitradurga Taluk and District.

BIDDERS SHALL NOTE: FILL ONLY IN LIGHT BLUE COLOURED CELLS

Bidders Name and Address along with GSTIN No.: To

The Chief Engineer, Electy., Tendering & Procurement, KPTCL, 9th Floor, Indhana Bhavan, A R Circle, BANGALORE - 560009.

Sl. No. Specifications Unit Quantity a) 66/11kV @ Belghatta S/s

B1 Construction of Embankment by excavating the available approved Gravel/ Murrum deposited at a place or borrow pits during or prior excavation with all lifts and lead, transportation to site, spreading, grading to required slope and compacting to meet the requirement complete as per specifications, including cost of labour,rolling,water,all materials, usage & all other appurtenaces required to complete the work. cum 19700.00

B2 Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work. In all kinds of soils Depth upto 3 m cum 4235.85

B3 Earth work excavation for pipeline trenches in all kinds of soils by mechanical means as per drawing and technical specifications, including setting out, construction of shoring, strutting, barricading, caution lights, bracing, using sight rails & bonding rods at every 100 mm wherever necessary as directed, removal of stumps and other deleterious matter, dressing of sides and levelling the bottom of trench to the extent required , utilising the available excavated earth locally for the work etc., and all other appurtenances complete in the following strata. cum 3825.00

B4 Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. Mix 1:3:6 (M10) Using 20 mm nominal size graded crushed coarse aggregates cum 1368.59

B5 Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing, form work, centering & scaffolding and all the other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates - For foundation (3% cosidered for Form work) cum 1067.14

B6 Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing, form work, centering & scaffolding and all the other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates- For Columns pedestal & coluimn upto plinth beam (70% considered for Form work) cum 5.92

B7 Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing, form work, centering & scaffolding and all other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates For Beams & lintels (60% considered for Form work) cum 49.10

B8 Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing, form work, centering & scaffolding and all other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates For Roof slab (50% considered for Form work) cum 70.42

B9 Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing, form work, centering & scaffolding and all other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates For Chejjas & Canopy of CRB (45% considered for Form work) cum 8.45

B10 Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing, form work, centering & scaffolding and all other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates- For Columns (70% considered for Form work) cum 29.99

B11 Providing and laying in Cement Concrete for all Basement & surface level works, return walls, retaining walls, sunken floors etc. The granite/trap/ basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, form work, centering & scaffolding and all other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates- For Plinth beam (50% considered for Form work) cum 11.90

B12 Providing and laying in Cement Concrete for all Basement & surface level works, return walls, retaining walls, sunken floors etc. The granite/trap/ basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers, laid in layers, well compacted using needle vibrators, providing weep holes wherever necessary, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing and all other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates- (10% considered for Form work) cum 629.41

B13 Providing and laying in position Cement Concrete for all Super structures of building , Road works, Water works, Irrigation works & super structure works of bridges upto 3.50 m height. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticisers laid in layers, well compacted using needle vibrators. The cost includes all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes , labour, Usage charges of machinery, curing, form work, centering & scaffolding and all other appurtenances required to complete the work as per technical specifications. M40 Design Mix Using 20 mm nominal size graded crushed coarse aggregates (5% considered for Form work) cum 80.10

B14 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller in stages to propeProviding, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver/grader in sub-base / base course on well prepared surface and compacting with vibratory roller to achieve the desired densityr grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density. cum 910.40

B15 Jelly Spreading (20-25 mm) : Supplying and providing jelly in the station yard of uniform thickness of 25 mm including the cost of materials, labour charges, required tools and plants etc., complete. Work shall be carried out as per the instructions of Engineer in-charge of works as per the standard procedure. sqm 6881.60

B16 Prime Coat over WMM/WBM: Providing and applying primer coat with SS1 grade Bitumen Emulsion on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70 kg per m2 using mechanical means. sqm 8096.00

B17 Tack coat on Bituminous surface Providing and applying tack coat with VG-10 Bitumen using pressure distributor at the rate of 0.25 kg/m2 on the prepared bituminous surface cleaned with mechanical broom. sqm 16192.00

B18 Bituminous Macadam Grading - I for traffic less than 20 MSA Providing and laying Bituminous Macadam with 100 tph capacity hot mix plant batch type using crushed aggregates of specified grading premixed with bituminous binder VG-30 @ 3.3% by weight of mix, transported to site, laid over a previously prepared surface with mechanical paver finisher to the required grade, level and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction cum 404.80

B19 Bituminous Concrete Grading I for traffic less than 20 MSA Providing and laying Bituminous Concrete with 100 TPH capacity hot mix plant batch type using crushed aggregates of specified grading, premixed with bituminous binder VG-30 @ 5.2 per cent of mix and filler, transporting the hot mix to work site, laying with mechanical paver finisher to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects cum 202.40

B20 Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 14:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 140 kg/ m3 , optimum moisture content to be determined during trial length construction, concrete strength not to be less than 7 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 t vibratory roller, finishing and curing. cum 50.40

B21 Steel Fabrication: Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification Buildings kg 28688.36

B22 Steel Fabrication: Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification All other type of structures kg 89294.75

B23 Providing and fixing Structural Steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge. kg 18415.90

B24 Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing, and all the other appurtenances required to complete the work as per technical specifications. Mix 1:2:4 Using 20 mm nominal size graded crushed coarse aggregates (For coping, sills and floor bed, screed concrete) cum 70.03

B25 Providing Size Stone masonry with hard stone in foundation & plinth with Cement mortar 1:6 (1 cement : 6 coarse sand) cum 5.40

B26 Providing Flush/ Ruled pointing: Pointing on stone work with cement mortar 1:3 (1 cement : 3 fine sand) after raking joints to depth nicely lining, including cost of materials, labour, curing as per specifications and as per directions of Engineer-in-charge. sqm 7.80

B27 Providing Brick work with common burnt clay Non Modular bricks of class designation 3.5 in super structure above plinth level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand) including cost of all materials, labour, scaffolding and usage charges of machinery & other incidental charges complete as per the direction of engineer incharge of work. cum 167.55

B28 Providing and constructing load bearing wall with Solid Concrete blocks of size 400x200x200mm having block density more than 1800kg/m3 and minimum compressive strength of 4.00 N/mm2 conforming to IS 2185 (Part - I) - 2005 and constructed with CM 1:4 as per IS 2572:2005 including cost of all materials, labour, scaffolding and curing, usage charges of machinery etc complete as per specifications sqm 518.40

B29 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. cum 1745.24

B30 Providing 20 mm cement plaster of mix :1:4 (1 cement: 4 fine sand) to brick/stone masonary including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge sqm 1227.62

B31 Providing 15 mm cement plaster on the rough side of single or half brick wall of mix 1:4 (1 cement: 4 fine sand) including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge. Sqm 2501.06

B32 Providing 12 mm cement plaster with cement mortar 1:4 (1 cement: 4 fine sand) to brick masonry including rounding off corners wherever required smooth rendering, providing and removing scaffolding, including cost of materials, labour, curing complete as per specifications and as per directions of Engineer-in-charge. Sqm 479.68

B33 Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer including cost of materials ,labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge. sqm 8.04

B34 Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete including cost of materials, labour, usage charges of machinery complete as per specifications no 6.00

B35 Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : 125x85x5.5 mm (heavy type) no 12.00

B36 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in- charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts bolts, fasteners etc.) including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge kg 341.69

B37 30mm thick factory made polyvinyl chloride (PVC) door shutter made of a uPVC hollow section of size 60x30mm and wall thickness 2 mm (plus or minus 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (plus or minus 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x30mm and 2 mm (plus or minus 0.2 mm), wall thickness. Fixed to the shutter styles by means of plastic/galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (plus or minus 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in–charge. sqm 28.14

B38 Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance plus or minus 1mm), with wall thickness 2.0 mm (plus or minus 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (plus or minus 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineer- in-charge. 48x40 mm PVC Extruded section m 67.10

B39 Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross- section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame. m 33.00

B40 Providing and fixing to existing door frames Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames. sqm 10.80

B41 Providing & fixing of 3-track x 2-panel sliding windows made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastomer) and lead free, gaskets -grey colour having isolated drainage and reinforced with Galvanized Iron profile through-out the window frame. The outer frame having an overall size of 108mm width x 45mmheight with reinforcement of 1mm thickness and Sash with overall size of 39mm x 75mm with GI reinforcement of 2mm and mesh sash of size 37mm x 58mm. Coextruded Glazing bead for fixing of glass shall be of size 20mm x 24 mm. Windows shall be provided with 6mm plain float glass, standard hardware& Multi point locking system with touch lock. Wall thickness of frame & sash shall be of 2mm-2.5mm. Maximum possible size – 2419mm x 2200mm. (The cost is inclusive of all fixtures and separate charges for minor T&P's shall not be made). sqm 48.00

B42 Providing & fixing of louvered ventilator made out of multi chambered UPVC(Matching to RAL-9016) sections and with minimum TiO2(Titanium Dioxide) at 6PHR with TPE(Thermo Plastic Elastomer) and lead free with gaskets -grey colour having isolated drainage and reinforced with Galvanized Iron profile through-out the ventilator frame. The frame having overall size of 39mm x 39mm with GI reinforcement of 1mm thickness. Louver clip in Aluminium (powder coated in white) will be used on the frame along with plastic parts for fixing the 4 mm pin head glass. Wall thickness of frame shall be 2mm.Maximum possible size – 1000mm x 1000mm.(The cost is inclusive of all fixtures and separate charges for minor T&P's shall not be made) sqm 2.70

B43 Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc. for: PVC pipes 110mm dia., 6 kg/sqcm & class 3 m 240.00

B44 Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc. for: PVC pipes 63mm dia., 6 kg/sqcm & class 3 m 186.00

B45 Supplying PVC ringtite pipes conforming to IS 4985:2000 with latest amendments and conveying to worksite, rolling and lowering into trenches, laying true to line and level and perfect linking at joints, testing and commissioning, including loading unloading at both destinations and cuts of pipes wherever necessary including jointing of PVC pipes and specials (excluding cost of specials) with jointing of approved type, with all labour with all lead & lift including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excavation etc. complete and giving necessary hydraulic test to the required pressure as per ISS (Contractor will make his own arrangements for procuring water for testing) etc. for: PVC pipes 160mm dia., 6 kg/sqcm & class 3 m 449.00

B46 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps each 2.00

B47 Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests each 4.00

B48 Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Oval shape 450x350 mm (outer dimensions) each 2.00

B49 Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS: 12701 marked, with cover and suitable locking arrangment and making necessary holes for inlet, outlet and overflow pipes but without fitting and the base support for tank. L 2000.00

B50 Constructing brick masonry chamber of internal dimension 600x600mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plastering 12 mm thick with cement mortar 1:4, CC 1:2:4 coping 75mm thk for fixing CI cover & frame etc. excluding the cost of CI cover & frame. each 20.00

B51 Constructing brick masonry chamber of internal dimension 450x450mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plastering 12 mm thick with cement mortar 1:4, CC 1:2:4 coping 75mm thk for fixing CI cover & frame etc. excluding the cost of CI cover & frame. each 23.00

B52 Providing and fixing SFRC frame and cover conforming to IS 12592 (part-I)-1988 and IS 12592 (part-II)- 1991 with latest amendment, including cutting slabs to the required size for the opening and fixing the cover in C.C. 1:2:4 and C.M. 1:3 plastering 20 mm thick to all exposed faces, curing for 10 days with all lead and lift with apurtenances. complete. Medium Duty Set 43.00

B53 Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. (Made of G.I. wire of dia 4 mm sqm 324.00

B54 Fencing with G.I. barbed wire Angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used. With G.I. barbed wire m 2592.00

B55 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 25mm nominal dia Pipes m 50.00

B56 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 20mm nominal dia Pipes m 100.00

B57 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 32mm nominal dia Pipes m 250.00

B58 Providing S&S RCC SPUN / VIBRATED CAST PIPES (REINFORCED) pipes NP-3 Class conforming to IS:458-1988 with latest amentments using ordinary portland cement, for sanitary works and conveying to work site, rolling and lowering into trenches, laying true to line and level including loading and unloading at both destinations and jointing of pipes and specials, perfect linking of joints with jack to correct position including cost of jointing materials, i.e, rubber rings conforming to IS: 5382 for S&S RCC pipes, with all leads and lifts as directed and giving necessary hydraulic test as per ISS to the required pressure and commissioning etc. complete. (Contractor will make his own arrangements for procuring water for testing). Before the execution of the work, the contractor shall carry out the survey. RCC NP3 Class pipe of 900 mm dia. m 12.00

B59 Providing S&S RCC SPUN / VIBRATED CAST PIPES (REINFORCED) pipes NP-3 Class conforming to IS:458-1988 with latest amentments using ordinary portland cement, for sanitary works and conveying to work site, rolling and lowering into trenches, laying true to line and level including loading and unloading at both destinations and jointing of pipes and specials, perfect linking of joints with jack to correct position including cost of jointing materials, i.e, rubber rings conforming to IS: 5382 for S&S RCC pipes, with all leads and lifts as directed and giving necessary hydraulic test as per ISS to the required pressure and commissioning etc. complete. (Contractor will make his own arrangements for procuring water for testing). Before the execution of the work, the contractor shall carry out the survey. RCC NP3 Class pipe of 300 mm dia. m 180.00

B60 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :Two coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. sqm 462.91

B61 Providing and Applying CFTRI approved two component flexible polymer modified acrylic cementitious waterproofing coating with a mix ratio of (5 Liquid :7 Powder) to the RCC surface like Roof, bathroom, toilet, balcony & utility area applied @ 2.2kg/m2 in 2 coats to achieve 1.2mm DFT, having Elongation at break greater than 120% as per ASTM D 412, Tensile strength greater than 1N/mm2 as per ASTM D 412, Adhesion strength: 0.80N/mm2 as per ASTM D 4541, crack bridging upto 2mm as per ASTM C 836. The finished cost to include surface preparation, making coving of 50 mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and lay 45 gsm glass fibre mesh over the angle fillet when the first coat in still wet, treatment of cracks completely as per specification. sqm 354.92

B62 Providing and laying 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2L per 50 kg of cement or as per direction of Engineer incharge. sqm 72.25

B63 Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. ** Polished Granite stone slab Black, Cat Eye, River Pink or equivalent. sqm 334.18

B64 Providing and fixing 10 mm thick acid and or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding for Bathrooms: Toilet: Chemically exposed areas and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direc tion of Engineer-in- Charge. In flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) with Acid and alkali resistant tile sqm 20.00

B65 Providing and fixing 10 mm thick acid and/or alkali resistant tiles of approved make and colour using acid and/or alkali resisting mortar bedding for Bathrooms: Toilet: Chemically exposed areas and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge. In dado/skirting on 12 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) with Acid and alkali resistant tile. sqm 80.00

B66 Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/m2 including pointing the joints with white cement and matching pigment etc., complete. sqm 23.34

B67 Providing skirting, dadooing, rises of steps with white glazed tiles 6mm thick on 10mm thick cement plaster 1:3 and jointed with white cement slurry over existing rough plaster surface using glazed tiles of approved make and size including cost of materials, labour, complete as per specifications. Sqm 96.04

B68 Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete as per specifications and as per directions of Engineer in charge. sqm 1022.30

B69 Providing and fixing PTMT stop cock of approved quality and colour 15 mm nominal bore, 86 mm long, weighing not less than 88 g No 20.00

B70 Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangements of approved quality and colour. 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190g. no 5.00

B71 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 20 mm nominal bore no 25.00

B72 Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm nominal bore no 5.00

B73 Providing and fixing Rainy dual capacity self-cleaning roof top rain water harvesting filter or equivalent filter of FL-500 specification suitable for a catchment area of about 500Sqm. No 1.00

B74 Providing, supplying to work site,Single Phase Submersible Pump Sets of 100mm dia (4 inch) suitable for bore well confirming to IS 8034-2000 specifications,with testing of as per instructions of engineer incharge of work and latest amendments 1.50 HP/1.1KW 12 STG No 1.00

B75 Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives, New work (Two coats applied @ 1.43 litre/ 10 m². Over and including priming coat of exterior primer applied @ 0.90 litre/10 m² with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. Sqm 1324.75

B76 Finishing walls with Acrylic Smooth exterior paint of required shade :New work (Two coat applied @ 1.67L/10 m² over and including priming coat of exterior primer applied @ 2.20 kg/10 m²) with paint of approved quality to give an even shade, after thoroughly brooming the surface to remove all dirt, dust, mortar drops and foreign matter including preparing the surface even and sand paper smooth, cost of materials, labour complete as per specifications and as per directions of Engineer-in-charge. sqm 2475.66

B77 Providing and fixing Modular multi-diameter cable sealing system which is waterproof,fire proof& rodent proof consisting of frames,blocks and accessories to be installed wherever the electrical(power/control cables/instrumentation/communication cables and under-ground and over ground at entry and exit of control room as per directions of engineer incharge of work. no 4.00

B78 Sinking borewell of 165mm dia. clear, using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF and above, in all strata of earth, including over burden upto 20M, fixing of casing pipes, collars and cap with ncessary cutting, threading and welding including transportation of rig and supporting vehicles, crew charges, cost of consumables, cost of yield test at the final depth with a minimum working of compressor for one hour etc. complete. The cost excludes the cost of casing pipes, collars and caps etc.) for: Borewell depth of 0 to 50 m - Water supply Upto 50.00 mtrs. m 50.00

B79 Sinking borewell of 165mm dia. clear, using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF and above, in all strata of earth, including over burden upto 20M, fixing of casing pipes, collars and cap with ncessary cutting, threading and welding including transportation of rig and supporting vehicles, crew charges, cost of consumables, cost of yield test at the final depth with a minimum working of compressor for one hour etc. complete. The cost excludes the cost of casing pipes, collars and caps etc.) for Borewell depth of 50 to 100 m m 50.00

B80 Sinking borewell of 165mm dia. clear, using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF and above, in all strata of earth, including over burden upto 20M, fixing of casing pipes, collars and cap with ncessary cutting, threading and welding including transportation of rig and supporting vehicles, crew charges, cost of consumables, cost of yield test at the final depth with a minimum working of compressor for one hour etc. complete. The cost excludes the cost of casing pipes, collars and caps etc.) for: Borewell depth of 100 to 150 m m 50.00

B81 Sinking borewell of 165mm dia. clear, using super fast hydraulic rig of capacity 300 PSIG & above 1100 CMF and above, in all strata of earth, including over burden upto 20M, fixing of casing pipes, collars and cap with ncessary cutting, threading and welding including transportation of rig and supporting vehicles, crew charges, cost of consumables, cost of yield test at the final depth with a minimum working of compressor for one hour etc. complete. The cost excludes the cost of casing pipes, collars and caps etc.) for: Borewell depth of 150 to 200 m m 50.00

B82 Supply of ISI mark 175mm nominal bore,plain and steel casing pipe grade of steel Fe 410 of wall thickness conforming to IS 4270-2001 and latest ammendments, electrical resistance welded steel tubes, material and conforming to IS 1387-1993 and manufactured by basic open hearth electric or basic oxygen process in random length of 5-7m both ends.threaded conforming to IS 554-1985 one end fixed with socket conforming to IS 4270-2001 and the other end with screwed pipes all shall be responsibaly free from defects. The tubes shall be responsible straight end should be with ISI marking weighing 25.10kg/m.prices include Collar-Medium duty m 30.00

B83 Providing and laying at site of work MS casing caps as per IS 1239 (part- II) 1982 with all latest amendments if any for any dia. The thickness of plate used for covering one end shall be 3mm (minimum). The dimensions of caps and colars shall be strictly as per IS 1239 (Part-II) 1982 with all amendments including cost of material and labour charges for fixing, if any etc. complete with all lead and lifts and as directed by the Engineer in charge each 1.00

B84 Providing and fixing MS casing collars as per IS 1239 (part-II) 1982 with all latest amendments if any for any dia. The thickness of plate used for covering one end shall be 3mm (minimum). The dimensions of caps and colars shall be strictly as per IS 1239 (Part-II) 1982 with all amendments each 1.00

B85 Geophysical investigation at site for sinking borewells for supplying drinking water to the habitation either through the Hand Pump MWS or P.W.S.S, by vertical electrical sounding by adopting Venner or Schlumbergers’s method, including reconnaissance survey of geological formation. Geophysical investigation of existing ground water in the vicinity, its quality, quantity and acceptability of the users, indicating the location of the site, recommended depth of casing pipe required to seal the top unconsolidated formation including an extra depth of 1.0 metre in consolidated formation for proper seating of casing pipe, depth of drilling required to cover full depth of aquifer proposed to be tapped, probable yield and other information required including transportation of instruments and accessories to work site, engaging technical personal and labour required etc. each 1.00

B86 PUMPSET : Providing Submersible Pump Set of 150mm dia suitable for bore well and confirming to IS 8034-2000 ; 3Phase, SS Bowl & Impeller with Low volt Motor as per specifications, to work site as per necessary ammendments and instructions of engineer incharge of work. 6.50 HP - 90 LPM @ 132 m = 15 STG Outlet Dia - 2.00” each 1.00

B87 SUBMERSIBLE CABLE Supply and delivery at site Brand new best make PVC insulated cable of Flat 3 core (sheathed) of nominal cross sectional area as per IS 694-1990 with ISI Mark and as per its latest amendments. 1x3x4 m2 m 200.00

B88 PRESSURE GAUGE : Supply and delivery at site of brand new best make pressure gauge bourdon type as per IS 778/1984 with ISI Mark and as per its latest amendments - Size 100 mm each 1.00

B89 GATE VALVE : Supply and delivery at site of brand new best make gate valve as per IS 778/1984 with ISI Mark and as per its latest amendments Size 50 mm each 1.00

B90 NON - RETURN VALVE : Supply and delivery at site of brand new best make non-return valve as per IS 778/1984 with ISI Mark and as per its latest amendments Size 50 mm each 1.00

B91 Control Panel BOARD-A: Supply, installing,testing and commissioning COMMON control panel consisting of the following INCOMING:1 No set of Phase indicating lamps with SFU of suitable rating 1 No, Analog Ammeter, 1 No Analog Voltmeter 1ni with Phase selector switch, Isolating switch OUTGOING for Main Electrical Pump: 1 No. MCB 1 No. DOL of S/D Starter suitable for respective HP 1 No. Electrcal Protection Like single Phase preventor, under voltage over Volage, under current over current & dry run protection suitable for the pump described above 1 no Indoor typ e NOTE: 1) DOLDirect Online Starter 2) S-D- Star Delta Starter for outdoor 6 -15 HP pumps each 1.00

B92 Supply and delivery at site best indigenous brand new power capacitor as per IS 2834/1986 with latest amendments with KPTCL authorities and erection, electrification and commissioning of the same at the location of respective pump sets. kVAR 1.00

B93 MCB: Supply and delivery at site delivery of best indigenous brand new MCB (Miniature Circuit Breakers) of required capacity as per IS 88228/1978 and its latest amendments and with ISI Mark of 6/10/16/20/25/40 Amps with scalable box. per 3 poles 1.00

B94 Erection elctrification & Commissioning works of pumpsets : Labour charges for Erection, Electrification and commissioning of Pump sets, including aligning and balancing of all items including supply and erection of two pair of supporting clamps, bore well caps, cable clips and water tight gland cable protectors, bolts, nuts, valve and gauges,tools and equipments etc., involved in the job as per specifications, with necessary tests as per specifications, with testing of as per instructions of engineer incharge of work Job 1.00

B95 Erection of panel board & meter board Unit : Labour charges for erection of outdoor type panel board and meter board units with all necessary materials and labour, tools and equipmentsincluding providing cement concrete foundation bed etc., complete as per specification, with testing of as per instructions of engineer incharge of work. Job 1.00

B96 Main connections: Providing main connection from pole PVC insulated sheathed steel wire cable in new trench as per IS 1554/ 1988 with latest amendments with ISI mark from KPTCL pole to meter board unit. m 50.00

B97 Providing, laying and jointing HDPE pipes of specified grade and conforming to IS 4984-2016 with latest ammendments and conveying to work site including loading and unloading at both destinations and rolling and lowering into trenches, laying true to line and jointing of pipes and specials with electrofusion welding, giving hydraulic test as per relevant ISS with all lead and lifts including encasing the pipe alround to a depth of not less than 15 cms. with soft gravel or selected earth available from the excation, testing and commissioning. The rate is exclusive of required specials and fittings wherever necessary like saddle Tee, stub ends, flanged sets, bedns, reducers etc. complete (Contractor will make his own arrangements for procuring water for testing) etc. complete. NOTE: Upto 110mm dia Coil shall be used. For :HDPE Grade PE100-PN8.0,63mm dia m m 120.00

B98 Earthing : Earthing: Providing and fixing and wiring earth electrode for grounding circuits IC cutouts and other equipments on the meter board in the pit. The pits should be filled up with equal proportion of salt and charcoal 150mm around the pipe to complete depth. The connection from the pipe to the conduits etc. is to established through GI wire of sizes as per clause 7.3.3 of IS 732 using 12mm bolts, nuts, washers and check nuts, the pipe shall have 16 through holes of 12mm dia. Job 1.00

B99 Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) without control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. a) Short point up to 3Mtr from tapping point to out let via switch box point 20.00

B100 Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) without control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. b) Medium point above 3Mtr up to 6Mtr from tapping point to out let via switch box point 23.00

B101 Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping using copper PVC insulated multi strand 2x1.5Sqmm copper wire without switch, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet.( 4/9) - II. Point wiring using class B Materialsc) Long point above 6Mtr up to 10Mtr from tapping point to out let via switch box point 25.00

B102 Concealed Conduit System Supplying heavy gauge PVC conduit pipe ...... mm dia..........mm thick confirming to IS 2509 with suitable size bends, metal/PVC Junction boxes, adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclosures, run with 18SWG GI fish wire wherever necessary 19/20mm dia 2mm thick m 250.00

B103 Concealed Conduit System Supplying heavy gauge PVC conduit pipe ...... mm dia..........mm thick confirming to IS 2509 with suitable size bends, metal/PVC Junction boxes, adhesive paste etc., and running before concreting the slab. The conduit should be tied to the reinforcement rods by using binding wires and unused ways of junction boxes and pipe ends should be covered using PVC end enclosures, run with 18SWG GI fish wire wherever necessary 25mm dia 2mm thick m 400.00

B104 Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) without control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. Two outlet in a row, above 3Mtr up to 6Mtr from tapping point to out let via switches box Each Point 10.00

B105 Point wiring using Copper wire without switch. Supplying and wiring adopting loop system in existing PVC Conduit /casing capping casing capping using 2x1.5Sqmm (Phase & Neutral) & 1x1.0 sqmm (Earth wire) FRLS multi strand PVC insulated copper wire (confirming to IS-694: and latest amendments) without control switch shall be fixed on the existing plastic sheet/ gang box, the other end of the wires shall be terminated with sufficient loose length in a wood/PVC round block. complete for each outlet. Three outlet in a row, above 6Mts up to 10Mtr from tapping point to out let via switches box Each Point 10.00

B106 Supplying 6A flush type socket and 6 A flush type SP switch either surface/flush mounting in existing gang box or in 4mm thick plastic sheet and fixing over a flush mounted wooden box and wiring using necessary capacity wires as required as per IS 1293 and IS 3854. 6A 2 Way each 15.00

B107 Supplying 6A flush type socket and 6 A flush type SP switch either surface/flush mounting in existing gang box or in 4mm thick plastic sheet and fixing over a flush mounted wooden box and wiring using necessary capacity wires as required as per IS 1293 and IS 3854. 6A 3/5 Way each 15.00

B108 Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293.32A DP Switch each 12.00

B109 Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. 6/16A Universal Socket each 15.00

B110 Supplying and fixing of modular switch & connected accessories on existing modular switch plate as per IS 3854 and IS 1293. TV/ Telephone Socket each 5.00

B111 Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS 694:201 1.5 sqmm m 500.00

B112 Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS 694:201 2.5 sqmm m 750.00

B113 Wiring for lighting/power circuit using one of FRLS PVC insulated 1100V grade, multistrand copper wire with low conductor resistance single core in open or concealed system of wiring with specified IS 694:201 4 sqmm m 300.00

B114 Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 1-2Way each 6.00

B115 Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 4-5Way each 10.00

B116 Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 6Way each 8.00

B117 Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 8Way each 12.00

B118 Supplying and flush mounting powder coated / galvanized metal box suitable for mounting modular switch plates. The box should be firmly flush mounted after due groove cutting in Brick/Stone/C.C wall 10-12Way each 8.00

B119 Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box 1 to 2 Module each 6.00

B120 Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box 4 Module each 10.00

B121 Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box 6 Module each 8.00

B122 Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box 8 Module each 12.00

B123 Supplying and fixing superior quality modular switch mounting polycarbonate plate with necessary supporting back plate with required nos. of machine screws, bolts nuts etc., complete on the existing metal/PVC box 10-12 Module each 8.00

B124 Supplying of 1440rpm heavy duty exhaust fan with bracket blades suitable to operate on 230V 50Hz, AC Supply complete. - 12" Sweep (300mm) each 4.00

B125 Supplying of 1440rpm heavy duty exhaust fan with bracket blades suitable to operate on 230V 50Hz, AC Supply complete. - 15" Sweep (450mm) each 3.00

B126 Supplying capacitor type ceiling fan complete with down rod blades, shackle, canopies etc., for operation on 230 volts, 50 cycles. Single phase AC supply conforming to ISS-374-1979 and with double ball bearing system 48" Sweep (1200mm) Regular model each 14.00

B127 Fixing a ceiling/wall mounting fan of all capacities and all types to the existing 'S'' hook with fan regulator to the existing board together with supplying and fixing 5 A. ceiling rose, necessary length of 23 / 0.0076 inch PVC insulated twin twisted copper wire and wiring. each 14.00

B128 Fixing one exhaust fan after making a suitable notch in the wall and finishing with cement mortar and colouring to match the existing wall or brackets, with bolts and nuts and a 5 A, ceiling rose with sufficient length of 23 / 0.0076 inch PVC insulated twin core wire of approved make with wire mesh and wooden frame. each 7.00

B129 Supplying and fixing Moulded Case Circuit Breaker (MCCB) over the existing wood/panel board using necessary screws, bolts, nuts, necessary phase separators, handle and wiring complete. Protection of Overload and Short circuitwith adjustable thermal magnetic release, Micro processor release shall have Earth Fault as per IS/IEC 60947-2 . (Icu=100% lcs). In 4P MCCB, all Poles should have protection for Short-Cicrcuit/Over Load. For Microprocessor MCCBS Facility for segregating Priority and Non-Priority loads must be available in the MCCB. MCCB shall be provided with double insulation (insulation between front cover and internal power circuits to avoid any accidental contact with live current carrying path with the front cover open). Multi-pole breakers shall be designed to break all the poles simultaneously and they shall have a single mechanism THREE POLE 200Amps 36kA each 2.00

B130 Supplying of Switch disconnector fuse unit (TPN) HRC type (but without HRC fuses). With AC-23A duty and as per IS-13947 - 125Amps each 1.00

B131 Supplying and fixing regular MCB distribution boards on wall / wood board / flush mounting using required clamps, bolts, nuts etc., with provision for fixing suitable type capacity MCB's single phase / 3 phase / single door with powder coated painting etc., Made out of 14 SWG MS enclosure - Double Door 12Way SP &N each 2.00

B132 Supplying and fixing regular MCB distribution boards on wall / wood board / flush mounting using required clamps, bolts, nuts etc., with provision for fixing suitable type capacity MCB's single phase / 3 phase / single door with powder coated painting etc., Made out of 14 SWG MS enclosure - Double Door 6 Way SP &N each 1.00

B133 Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898 6-32A SP each 12.00

B134 Supplying & fixing miniature circuit breakers on existing MCB distribution boards using necessary fixing materials and 'C' Type curve, indicator ON/OFF, energy cross-3 with Short circuit breaking capacity of 10K and complete wiring as required confirming to IEC 60898 50-63A SP each 5.00

B135 Supplying, fixing and wiring Residual current circuit breaker (RCCB) 240/450V upto 300mA sensitivity on existing wood/ panel board. 32-40 Amps 4 pole each 2.00

B136 Supplying and fixing of LED type panel board indicating lamp with required colour suitable for 230/440VAC. 50 Hz 12/24V D.C. each 1.00

B137 Supplying ......... amps rated 3phase with neutral bus bar using required capacity electrolytic alluminium strips covered with heat shrinkable coloured PVC sleeve, mounted on phenolic/FRP/DMC insulator which are mounted on powder coated 40x6mm M.S.flat frame work in existing panel board. The bus bar shall have suitable holes for termination of incoming and outgoing cables as per IS specification with necessary botls,nuts and washers etc., complete. 600Amps 4x75x10mm Alluminium Strips m 1.00

B138 Supplying, fixing, wiring, earth electrode for grounding conduits, I.C. cutouts and other equipments on the meter board using 40mm dia 2.90mm thick GI pipe 2.5 mtr long buried in a pit. The pit should be filled with equal proprotion of salt and charcoal 150mm alround the pipe to complete depth. The connection from the pipe to the conduit etc, is to be established through GI wire of size as per ISI specification 7.3.3. of IS 732 using 12mm dia bolts, nuts, washers and checknuts etc., the pipe shall have 16 through holes of 12 mm dia. no 3.00

B139 Supplying fixing and wiring earth electrode for grounding of lifts, transformers, DG sets etc using 40mm dia 2.9mm thick 2.5 mtr long GI pipe with GI funnel with mesh and suitable size reducer fixed on the top of the earth electrode. The funnel should be enclosed in a CC chamber of 400x400x400mm with a cast iron cover. The earth electrode shall have staggered holes of 12mm dia and the electrode should be covered 150mm alround with alternate layers of salt and charcoal from the bottom of the CC chamber. The connection from the electrode is to be established through GI strip using GI bolts and nuts. no 2.00

B140 Supplying, fixing and wiring 0 to 600Volts 96x96mm AC Voltmeter on existing panel/wood board. each 2.00

B141 Supplying, fixing and wiring 0 to 1500amps CT operated AC analog type Ammeter With out CT each 2.00

B142 Supplying and fixing Electronic Trivector Meter (ETV) suitable for operation LT operation and -CT operated meter in polycarbonate body in class 0.5 accuracy as per IS 14697 and completely wired each 1.00

B143 Supplying of feet -PVC Batten with integrated LED tube LED light fitting 1 x 4ft - 36/40 W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI greater than 80. Power Input: 220-240V@ 50/60Hz & Power factor greater than 0.9 along with CE approved. 2 years Warranty against any manufacturing defect working under standard electrical condition each 20.00

B144 Supplying of feet -PVC Batten with integrated LED tube LED light fitting 1 x 2ft - 9/10 W with high quality diffuser with Life of 25000 burning hours & 70% lumen maintenance with CRI greater than 80. Power Input: 220-240V@ 50/60Hz & Power factor greater than 0.9 along with CE approved. 2 years Warranty against any manufacturing defect working under standard electrical condition each 6.00

B145 Fabricating supplying and mounting MS box made out ....SWG suitable for floor /wall mounting, fully weather proof with provision for better heat dissipation, provided with hinged front cover, equipped with tamper proof locking arrangements, with suitable size clamps with necessary cable entry pipe with gland and box should be finished with 7tanks treatment with powder coated paint and finally finished with approved colour etc., complete - 16SWG sq cm 20000.00

B146 Supplying and Fixing of ---- mm dia class A GI pipe bracket upto 2 mtrs long bent at suitable angle and fixing to this bracket street light fitting of all capacities to GI or GI or rail or RCC pole / wall using suitable clamps, bolts, and nuts and wiring using suitable capacity wires. Using 32mm dia G.I.Pipe each 2.00

B147 Supplying of recess mounting non integrated type LED down light 36W luminaire comprising of pressure decast/ extruded aluminium housing, with spring loaded false ceiling clA, LED of Power/COB with CCT 6500 degree K, CRI greater than 70%. efficacy greater than 100 lumen per W, 120degree beam spread, life greater than 25000 burning hours and Compliance to IS10322/ IEC 60598, LM 79 & LM 80. The lamp compartment is enclosed with anti glare opal diffuser which enhances the lighting level. LED's are driven by HF electronic driver integrated in a separate control gear assembly., with PF greater than 0.95, power loss should less than 5% of lamp Wage, short circuit & open circuit protection to be integrated in the circuit, THD less than 20%, Life as per LM 79. The operating input voltage should be between 130 to 275 V. BIS Approved and Tested by NABL/CPRI accredited laboratory with 2 years Warranty against any manufacturing defect working under standard electrical condition LED modular down light 2'x2' 36 W each 32.00

B148 Supplying, fixing and wiring earth leakage relay with core balanced current transformer suitable for single phase 50HzAC with latest micro controller based, digital read out of percentage leakage current, programmable delay/auto/manual reset facility suitable to mounton DIN rail/ flush mounting on panel board. each 1.00

B149 Supplying and fixing of modular switch & connected accessorieson existing modular switch plate as per IS 3854 and IS 1293. Stepped Fan Regulator Two Module each 14.00

B150 Fixing all types and all capacities of fluorescent /false ceiling/ spot light/CFL/LED fittings indoor on the wall/ceiling/rafters/girders using 23/0.0076" twintwisted PVC insulated wires, required Nos of round blocks and clamps. On wall/ ceiling / Rafter / Girders. each 55.00

1) The uploaded drawings are indicative and are to be referred for guidance purpose only. However all foundations shall be designed to suit the site soil condition and as per the approved layout.

2) The land will be handed over " As is where is condition".

Place Designation

Name of the company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 3C(i) - Price Breakup for -TB Civil Portion

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidders Name and Address along with GSTIN No.: To

The Chief Engineer, Electy., Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore. - 560009.

Sl. No. Specifications Unit Quantity b) 66kV TB @ Chitradurga S/s

B1 Earth work in surface excavation for stripping, seating of bund, Road way, by manual means for lowering & leveling the ground for all works other than foundation & depth in all kinds of soil not exceeding 300mm as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage & other appurtenances required to complete the work. cum 250.00

B2 Earth work excavation by manual means for drains, canals, waste weir, draft, approach channels, key trenches, foundation of Buildings & bridges and such simillar works in all kinds of soils, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, removal of stumps and other deleterious matter, excavated surface leveled and sides neatly dressed disposing off the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools & other appurtenaces required to complete the work. In all kinds of soils Depth upto 1.5 m cum 122.85

B3 Providing and laying in position Cement Concrete for levelling course for all works in foundation. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machinery, curing and all the other appurtenances required to complete the work as per technical specifications. Mix 1:3:6 (M10) Using 20 mm nominal size graded crushed coarse aggregates cum 14.49

B4 Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing, form work, centering & scaffolding and all the other appurtenances required to complete the work as per technical specifications. M25 Design Mix Using 20 mm nominal size graded crushed coarse aggregates - For foundation (3% cosidered for Form work) cum 76.32

B5 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. cum 72.66

B6 Removal of Unserviceable Soil with Disposal upto a suitable distance as directed by the Engineer incharge of work cum 112.51

B7 Steel Fabrication: Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification All other type of structures kg 3052.92

B8 Providing and fixing Structural Steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including cost of materials, labour, usage charges of machinery complete as per specifications and as per directions of the Engineer-in-Charge. kg 1665.38

B9 Providing and installing at site of work P.V.C. pipes including cost of pipes and specials and labour, including lowering into trenches, laying true to line, level and perfect linking at joints leak proof including jointing of approved type with all labour charges and all lift charges, handling charges including encasing the pipe around to a depth not less than 15 cms with gravel or selected earth available from the excavation etc. complete. 10 Kg/m2: 160mm m 100.00

B10 Providing S&S RCC SPUN / VIBRATED CAST PIPES (REINFORCED) pipes NP-3 Class conforming to IS:458-1988 with latest amentments using ordinary portland cement, for sanitary works and conveying to work site, rolling and lowering into trenches, laying true to line and level including loading and unloading at both destinations and jointing of pipes and specials, perfect linking of joints with jack to correct position including cost of jointing materials, i.e, rubber rings conforming to IS: 5382 for S&S RCC pipes, with all leads and lifts as directed and giving necessary hydraulic test as per ISS to the required pressure and commissioning etc. complete. (Contractor will make his own arrangements for procuring water for testing). Before the execution of the work, the contractor shall carry out the survey. RCC NP3 Class pipe of 300 mm dia. m 50.00

B11 Constructing brick masonry chamber of internal dimension 600x600mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plastering 12 mm thick with cement mortar 1:4, CC 1:2:4 coping 75mm thk for fixing CI cover & frame etc. excluding the cost of CI cover & frame. each 4.00

B12 Constructing brick masonry chamber of internal dimension 450x450mm and depth of 600mm (inner dimensions) with modular bricks of CD 75 in cement mortar 1:6, bed concrete 150mm thick with 1:3:6, plastering 12 mm thick with cement mortar 1:4, CC 1:2:4 coping 75mm thk for fixing CI cover & frame etc. excluding the cost of CI cover & frame. each 3.00

B13 Providing and fixing SFRC frame and cover conforming to IS 12592 (part-I)-1988 and IS 12592 (part-II)- 1991 with latest amendment, including cutting slabs to the required size for the opening and fixing the cover in C.C. 1:2:4 and C.M. 1:3 plastering 20 mm thick to all exposed faces, curing for 10 days with all lead and lift with apurtenances. complete. Medium Duty Set 7.00

B14 Jelly Spreading (20-25 mm) : Supplying and providing jelly in the station yard of uniform thickness of 100 mm including the cost of materials, labour charges, required tools and plants etc., complete. Work shall be carried out as per the instructions of Engineer in-charge of works as per the standard procedure. sqm 600.00

B15 Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work. In all kinds of soils Depth upto 3 m cum 90.40

1) The uploaded drawings are indicative and are to be referred for guidance purpose only. However all foundations shall be designed to suit the site soil condition and as per the approved layout.

2) The land will be handed over " As is where is condition".

Place Designation

Name of the company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 3C(ii) - Price Breakup for -Line Civil Portion

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidders Name and Address along with GSTIN No.: To

The Chief Engineer, Electy., Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore. - 560009.

Sl. No. Specifications Unit Quantity

C1 Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work. In all kinds of soils Depth upto 3 m Cum 124.20

C2 Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work In all kinds of soils upto 3.0 m depth with 5% de-watering is assessed as per site condition Cum 621.01

C3 Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights,including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work. In ordinary/soft rock without blasting upto 1.5 m depth. Cum 298.08

C4 Earth work excavation for Foundation by mechanical means for all works & depth upto 3 m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights,including dressing of excavated surfaces, disposing off or levelling the excavated earth or sorting & stacking the selected earth for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, tools, usage of machinery & other appurtenaces required to complete the work. In ordinary/soft rock without blasting Depth exceeding 1.5 m but not exceeding 3 m depth Cum 1192.34

C5 Earth work excavation for Foundation by Mechanical means depth upto 1.50m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including cost of explosives, dressing of excavated surfaces, disposing off or levelling the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, blasting materials, tools, usage of Machinery & all other appurtenaces required to complete the work. In Hard Rock (requiring blasting) Depth upto 1.50m Cum 49.68

C6 Earth work excavation for Foundation by Mechanical means depth upto 1.50m, as per drawing and technical specifications, including setting out, shoring, strutting, barricading, caution lights, including cost of explosives, dressing of excavated surfaces, disposing off or levelling the excavated stuff or sorting & stacking the selected stuff for reuse in a radius of 50 m and lift upto 1.5 m including cost of labour, blasting materials, tools, usage of Machinery & all other appurtenaces required to complete the work. In Hard Rock ( requiring blasting) Depth exceeding 1.5 m, but not exceeding 3 m Cum 198.72

C7 Providing and laying in position plain cement concrete for levelling course for all works in foundation. The granite /trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed, laid in layers not exceeding 150 mm thickness, well compacted using plate vibrators, including all lead & lifts, cost of all materials of quality, labour, Usage charges of machineries, curing, and all the other appurtenances required to complete the work as per technical specifications. Mix 1:3:6 (M10) Using 20 mm nominal size graded crushed coarse aggregates Cum 42.88

C8 Providing and laying in position Cement Concrete for all Foundation works. The granite/trap/basalt crushed graded coarse aggregates and fine aggregates as per relevant IS Codes machine mixed with super plasticizers laid in finished layers, well compacted using needle vibrators, including all lead & lifts, cost of all materials, quality confirming to the requirements of relevant IS codes, labour, Usage charges of machinery, curing, form work, centering & scaffolding and all the other appurtenances required to complete the work as per technical specifications M20 Design Mix Using 20 mm nominal size graded crushed coarse aggregates For foundation Cum 391.64

C9 Steel Fabrication: Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/welding joints, tying with binding wire / soft annealed steel wire and other ancilary operations complete as per drawing and technical specification All other type of structures Kg 34632.00

C10 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations and other similar works etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. Cum 449.02

The Design shall be safe against all anticipated/possible forces and pressures. All necessary checks for the stability of the structure shall be carried out.

Place Designation

Name of the company

Place Designation

Name of the company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 4A Price Break up for MANDATORY SPARES -STATION SUPPLY PORTION

SHEET FOR TECHNO COMMERCIAL OPENING (Unpriced)

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer, Electy., Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore-560009.

BIDDERS SHALL NOTE: PLEASE FILL ONLY IN THE LIGHT BLUE COLOURED CELLS.

STATION MANDATORY SPARES PORTION

Sl No Item Description Unit Total Quantity Indicate whether "Own manufactured Item" or "Bought Out Item" Indicate country of Origin

SM1 Circuit Breaker (CB) Closing coil with resistor (For one Complete Circuit Breaker) for 72.5KV CB Set 1

SM2 Tripping coil with resistor (For one Complete Circuit Breaker) for 72.5KV CB Set 1

SM3 Terminal Pad (For one Complete Circuit Breaker) for 72.5KV CB Set 1

SM4 Terminal Connector (For one Complete Circuit Breaker) for 72.5KV CB Set 1

SM5 SF6 Gas (40% of total gas Qty. of each Sub-Station) Sub-Station at Rangasamudra(Madegowdanahundi) LS 1

SM6 Isolator : Copper Contact fingers male & female (For one Complete Isolator for 72.5KV class) Set 1

SM7 Terminal Connector (For one Complete Isolator for 72.5KV Class) Set 1

SM8 Terminal Pad (For one Complete Isolator for 72.5KV Class) Set 1

Note: 1. Supply of equipment and materials shall include loading and unloading

2. Insurance cover should be taken in accordance with the provisions of the Bidding Documents.

3.The Bidder shall clearly indicate whether the materials/equipments are “Own manufactured” or “Bought out item”.) .

Place Designation

Date Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-5 COMMERCIAL DEVIATION

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Please fill Only in the Light Blue Couloured Cell.

Please key in the SlNo.,Section , Clause , Description as given in bid sheets and finally your Statement of Deviation/Variations.

This Sheet would be opened at the Techno-Commercial Opening. Please refer Vendor Manual attached for further details.

For any further assistance for submitting your bids please call up KPTCL Office.

We agree to provide all original Documents in support of the information provided for verification upon request. (Key in as YES in the space provided)

We understand that the electonic bid submitted by us is a valid offer in accordance with IT Act. (Key in as YES in the space provided)

We are fully aware of the electronic bid formalities and abide by the same. (Key in as YES in the space provided)

If you are not deviating from any of the clauses mentioned please key in as 'NO DEVIATION' in the space provided.

Bidder's Name & Address alongwith GSTIN no. :

The Chief Engineer, Electy., Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore. - 560009.

I/we have read each of the Clauses mentioned in INVITATION FOR TENDERS , INSTRUCTION TO TENDERERS , CONDITIONS OF CONTRACT, SPECIAL CONDITIONS OF CONTRACT and COMMERCIAL TERMS AND CONDITIONS and all the sections of Bid documents.

The following are the commercial Deviations and Variations from and exceptions to the Specifications and documents for

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

These deviations and variations are exhaustive. Except these deviations, the entire work shall be performed as per your specifications and documents.

Sl. NO. SECTION CLAUSE NO. DESC. AS PER SPECIFICATION STATEMENT OF DEVIATIONS/VARIATIONS

Note : Deviations specified elsewhere in the specification will not be considered.

Place Designation

Name of the company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-6 : TECHNICAL DEVIATION

SHEET FOR TECHNO-COMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Please key in the SlNo., Section , Clause , Description as given in Bid sheets and finally your Statement of Deviation/Variations.

This Sheet would be opened at the Techno-Commercial Opening.

For any further assistance for submitting your bids please call up KPTCL office. Please fill only in the blue coloured cells.

We agree to provide all original Documents in support of the information provided for verification upon request. (Key in as YES in the space provided)

We understand that the electonic bid submitted by us is a valid offer in accordance with IT Act. (Key in as YES in the space provided)

We are fully aware of the electronic bid formalities and abide by the same. (Key in as YES in the space provided)

If you are not deviating from any of the clauses mentioned please key in as 'NO DEVIATION' in the space provided.

Bidder's Name & Address alongwith GSTIN no. : TO,

THE CHIEF ENGINEER (ELECTRICTICTY), TENDERING AND PROCUREMENT, KPTCL,9TH FLOOR, INDHANA BHAVANA, A.R CIRCLE, BANGALORE-560009

The following are the Technical Deviations and Variations from and exceptions to the Specifications and documents for

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

These deviations and variations are exhaustive.Except these deiviations and variations, the entire work shall be performed as per your specification and documents.

Sl. NO. SECTION CLAUSE NO. DESC. AS PER SPECIFICATION STATEMENT OF DEVIATIONS/VARIATIONS

Note : Deviations specified elsewhere in the specification will not be considered.

Place Designation

Name of the company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE 7(List of special tools and tackles )

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidder's Name & Address alongwith GSTIN no. : TO,

THE CHIEF ENGINEER (ELECTRICTICTY), TENDERING AND PROCUREMENT, KPTCL,9TH FLOOR, INDHANA BHAVANA, A.R CIRCLE, BANGALORE-560009

List of special tools and tackles the price of which is included in bid price.

Sl. No. For equipment Description of item Unit Quantity

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

NOTE: 1 ) SHALL BE UPLOADED WITHOUT PRICES

Bidder's Name & Address alongwith GSTIN no. : To,

The Chief Engineer, Electy., Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore. - 560009.

We have uploaded with our proposal the following additional information.

Sl. No. Brief Description of information Ref. and Page No.

Place Designation

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (1 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

BIDDER'S NAME AND ADDRESS: TO,

THE CHIEF ENGINEER (ELECTRICTICTY), TENDERING AND PROCUREMENT, KPTCL,9TH FLOOR, INDHANA BHAVANA, A.R CIRCLE, BANGALORE-560009

a) * We have submitted bid as individual Bidder. (Key in Individual Bidder )

b) * We have submitted bid in Consortium with the following Bidders. (Key in Consortium )

Name of Consortium Partner Scope / Participation of each Consortium Partner

(* Fill-up whichever is applicable)

1.0 GENERAL INFORMATION

The Bidder, bidding for this package are requested to complete the information in the following form.

Sl. No. Particulars Bidder Details

1 Name of the Firm

2 Address of Head Office / Registered Office GST no.

5 Name of Contact person with Designation

6 Place of Incorporation/Registration

7 Year of Incorporation/Registration

8 Constitution or legal status of Tenderer [Upload copy]

9 Place of Registration [Upload copy]

10 Principal place of business

2.0 We are furnishing the following details/documents in support of Qualifying requirement for above mentioned project

Sl.No. Particulars For individual Bidder In case of Consortium :

Lead Bidder Consortium partner

(a) Written power of attorney of the signatory on the bid to commit the bidder.

1 Uploaded / Not

(b) Certificate of Registration of the Company. Please mention the date of incorporation of the company

1 Uploaded / Not

(c ) Valid Super Grade Electrical Contractor's License issued by Govt. of Karnataka OR valid Form J-1 Verification Letter issued by Chief Electrical Inspectorate, Govt. of Karnataka to Other State Electrical Contractor License Holder for the highest system voltage specified in the tendered work and Consortium Partner shall possess valid Super Grade Electrical Contractor's License issued by Govt. of Karnataka OR valid Form J-1 Verification Letter issued by Chief Electrical Inspectorate, Govt. of Karnataka to Other State Electrical Contractor License Holder for the highest system voltage specified in the tendered work OR valid Class-A/Class-1 Electrical Contractors License issued by any State/Central Government in India as on the date of techno commercial Bid opening. Please mention the date of expiry of the License certificate issued by GOK/ Undertaking to this effect

1 Uploaded / Not

(d) Self declaration regarding Litigation w.r.t KPTCL contracts over the last five years (refer IFT)

1 Uploaded / Not

(e) Self declaration for ‘not being disqualified regarding non-performance in any of the Government utilities in the past five years’. (refer IFT)

1 Uploaded / Not

(f) An undertaking to source the supply of equipment/ material from KPTCL approved vendors only as per QR for Vendor registration, available in the KPTCL website ie., kptcl.karnataka.gov.in, Link Tendering & Procurement-Application for Vendor.

1 Uploaded / Not

(g) Self declaration regarding no action against the bidder have been taken by KPTCL in respect of Risk & Cost clause

1 Uploaded / Not

(h) Self declaration regarding 'Eligibility clauses in respect of restrictions on procurement from a bidder of a country which shares a land border with India as per Annexure-XVI

1 Uploaded / Not

(i) Self declaration regarding RESTRICTIONS ON SOURCING OF EQUIPMENTS/MATERIALS BY THE BIDDER FROM A VENDOR OF A COUNTRY WHICH SHARES A LAND BORDER WITH INDIA as per Annexure -XVII

1 Uploaded / Not

Section 3 : 1.3 Work performed of similar nature in the last Ten years of both Lead Bidder & Consortium partner (in case of Consortium) as per Clause No: 3.2 (b) (i) & (ii) of ITT

Project Name Name & Address of the Employer Description of Work Voltage class Number of Sub-Stations/TBs/Length of the Line Contract Number Value of contract Rs. Lakh Date of issue of work order Specified period of completion Actual date of commissioning Remarks explaining reasons for delay in commisioning of work

Name of Consortium Partner

Note : 1 . The documentary proof of fulfilling the qualifying requirements shall be uploaded along with the bid. (i) The bidder shall upload the P.O,LOI/LOA, DWA, Work done, Performance Certificates issued by the end users not below the rank of Executive/ Divisional Engineer along with the bid. (ii) The work experience of Bidders who have executed DCW works/ Self execution works under the supervision of KPTCL officers and the works executed for BMRCL/ KIADB/ BDA/KBJNL/IPP works/other Government or Public sector organizations will also be considered subject to fulfilling the stipulated qualifying requirements and uploading necessary documentary evidence

2. The qualifying experience of the Bidder and Consortium Partner(in case of Consortium) who is having qualifying experience shall be furnished in the above performa and Documentary Proof in support of above shall be uploaded in the form of certificates issued by authorized officers of concerned organisations.

3. IF this sheet is insufficient for furnishing the qualifying experience of the Bidder then similar sheets shall be seperately uploaded.

4. In case of work executed under a contract that had been awarded on a joint venture, the experience of individual joint venture partner shall be considered limited to the scope of that partner under the said contract. The copy of the agreement executed with awarding agency shall be uploaded as proof of the same

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (2 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

BIDDER'S NAME AND ADDRESS: TO,

THE CHIEF ENGINEER (ELECTRICTICTY), TENDERING AND PROCUREMENT, KPTCL,9TH FLOOR, INDHANA BHAVANA, A.R CIRCLE, BANGALORE-560009

Section 3 : 1.5 Information on works for which Tenders have been submitted and works which are yet to be completed as on the date of this Tender of a Bidder

(A) Existing commitments and on-going works:

Description of work Place & State Contract No & Date Name and Address of Employer Value of contract (Rs. Lakh) Stipulated period of cof Completion Value of works remaining to be completed ( Rs.Lakhs) (Attach Certificates from Engineers –in- Charge) Anticipated date of commissioning

Ex-Works GST Total (Ex-works + GST)

Name of the Lead Bidder

Name of the Consortium Partner

Note:Attach Certificates from Engineers –in- Charge

B)Works for which Tenders already submitted

Description of work Place & State Name and Address of Employer Estimated value of works (Rs. Lakh) Stipulated period of Completion Date when decision is expected Remarks if any

Ex-Works GST Total (Ex-works + GST)

Name of the Lead Bidder

Name of the Consortium Partner

i) The statements showing the value of existing commitments and on-going works as well as the stipulated period of completion remaining for each of the works listed should be countersigned by the Employer in charge, not below the rank of an Executive Engineer or equivalent. OR The statements showing the value of existing commitments and on-going works as well as the stipulated period of completion remaining for each of the works listed should be verified and certified by Chartered Accountant/ Cost Auditor. However, the Bidder has to upload the PO/Work Award copies for existing commitments and on-going works

ii) A self-declaration is to be uploaded by the Lead Bidder & Consortium partner (in case of Consortium) stating that "the information with regard to assessed available tender capacity (Works on Hand) furnished are correct

iii. Bidders shall furnish Certificate from Chartered Accountants for split details of Ex-works values and GST of Contract values of the works in the prescribed format as at Clause No. 1.5 of Section-3: Qualification Information by the Lead Bidder & Consortium partner (in case of Consortium)

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (3 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

BIDDER'S NAME AND ADDRESS: TO,

THE CHIEF ENGINEER (ELECTRICTICTY), TENDERING AND PROCUREMENT, KPTCL,9TH FLOOR, INDHANA BHAVANA, A.R CIRCLE, BANGALORE-560009

Following is the list of major supplied Substation equipments/accessories which are type tested and designed, manufactured by us in accordance with internationally recognised standards.

Sl. No. Item rating, type and Designation Qty Customer Date of Order Date of Supply Date of Commissioning Ref. of Cusomer's certificate of successful operation enclosed Ref. of layout & Customer's certificae for successful commission

Note: Documentary Proof in support of above shall be uploaded in the form of certificates issued by authorized officers of concerned organisations.

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE - 9 (4 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidder's Name & Address alongwith GSTIN no. :

THE CHIEF ENGINEER (ELECTRICTICTY), TENDERING AND PROCUREMENT, KPTCL,9TH FLOOR, INDHANA BHAVANA, A.R CIRCLE, BANGALORE-560009

Section 3 : 1.7 Reports on the financial standing of the tenderer(Lead bidder & Consortium partner (in case of Consortium)) ,such as Profit and Loss Statements and Auditor’s reports in the preceeding last five years, Audited Financial statements i.e Balance sheets, P&L statements, Turnover certificates duly certified by chartered Accountant as documentary evidence shall be uploaded.

SLNo. Particulars Year Lead Bidder Consortium Member

Mention Year Turnover excluding GST (in Rs.) GST Amount (in Rs.) Mention Year Turnover excluding GST (in Rs.) GST Amount (in Rs.)

Names of the constituent Firm

1 Annual turn over for the last Five years Year(1) 2020-21 2020-21

2 Liquid Assets / Credit availability or access to evidence of assets

3 Whether Audited Balance sheets and Profit & Loss statement are enclosed for the last Five Years ? (yes/No)

4 Whether Bankers certificate enclosed for credit facilities? (Yes/No)

Note: Bidders shall furnish Certificate from Chartered Accountants for split details of financial Turnover and GST in the prescribed format (Annexure-XX) of tender document.

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 9 (5 of 5) : QUALIFYING REQUIREMENTS

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

BIDDER'S NAME AND ADDRESS: TO,

THE CHIEF ENGINEER (ELECTRICTICTY), TENDERING AND PROCUREMENT, KPTCL,9TH FLOOR, INDHANA BHAVANA, A.R CIRCLE, BANGALORE-560009

The information to be filled in by the Tenderer hereunder will be used for purposes of computing Tender capacity as provided for in Clause 3 of the Instructions to Tenderers. This information will not be incorporated in the Contract.

Lead Bidder Consortium partner Attach Copy

1.1 Constitution or legal status of Tenderer [Upload copy]

Place of Registration [Upload copy]

Principal place of business

Section - 3: 1.2 Total value of works executed (KPTCL & Non KPTCL works) excluding GST and payments received in the last five years (in Rs. Lakhs) of both Lead Bidder & Consortium partner (in case of Consortium).

1.2 Total value of works executed (KPTCL & NON KPTCL works) and payments received in the last five years (in Rs. Lakhs) of both Lead Bidder & Consortium partner (in case of Consortium). Financial Year KPTCL works Non KPTCL works

Individual Bidder In case of Consortium Individual Bidder In case of Consortium

Total value of works Excluding GST in Rs. Lakh Lead Bidder Consortium Partner Total value of works Excluding GST in Rs. Lakh Lead Bidder Consortium Partner

Total value of works Excluding GST in Rs. Lakh Total value of works Excluding GST in Rs. Lakh Total value of works Excluding GST in Rs. Lakh Total value of works Excluding GST in Rs. Lakh

Note: Attach relevant Certificate/s from Chartered Accountant.

Section 3: 1.9 Name, address, telephone number & e-mail id of the Tenderers' bankers who may provide references if contacted by the Employer:

1.9 Sl.No Name, address, telephone number & e-mail id of the Tenderers' bankers

Section 3: 1.12 Information on litigations in which the Tenderer is involved:

Other Party(ies) Employer Details of Dispute Amount involved Remarks showing Present Status

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-10 (1 of 3) Details of Tools and Plants available

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

BIDDER'S NAME AND ADDRESS: To

THE CHIEF ENGINEER (ELECTRICTICTY), TENDERING AND PROCUREMENT, KPTCL,9TH FLOOR, INDHANA BHAVANA, A.R CIRCLE, BANGALORE-560009

Following are the details of the Tools and Plants available with us.

Sl. No. Description Quantity Make Present Location / Project Remarks (if any)

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE 10 (2 of 3) Details of Technical staff employed

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

BIDDER'S NAME AND ADDRESS: To

THE CHIEF ENGINEER (ELECTRICTICTY), TENDERING AND PROCUREMENT, KPTCL,9TH FLOOR, INDHANA BHAVANA, A.R CIRCLE, BANGALORE-560009

Section 3: 1.8 Qualification and experience of the key technical and management personnel in permanent employment with the tenderer and those that are proposed to be deployed on this contract, if awarded

Sl. No. Name of the employee Designation Branch (Degree/Diploma) Year of Passing Since when employed in erection division Past Experience

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE 10 (3 of 3 )

SHEET FOR TECHNOCOMMERCIAL OPENING

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

BIDDER'S NAME AND ADDRESS: To

THE CHIEF ENGINEER (ELECTRICTICTY), TENDERING AND PROCUREMENT, KPTCL,9TH FLOOR, INDHANA BHAVANA, A.R CIRCLE, BANGALORE-560009

We propose the following deployment of manpower for the substation and Line package.

Sl. No. Category MONTHS AFTER PLACEMENT OF AWARD LETTER

1 Project manager

2 Sr. Project Manager

5 Skilled labour

6 No skilled labour

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-11 (A) : COMPLETION SCHEDULE FOR STATION/TERMINAL BAYS

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidders Name and Address: To,

The Chief Engineer, Electy., Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore. - 560009.

We hereby declare that following schedules shall be followed by us for the above work. The period of various activities from the date of placement of award letter shall be as follows

SL.NO Activity Period in Months for the work of Substations

Commencement Completion

1 Detailed engineering

2 Procurement of bought out items / raw materials

3 Manufacturing & Testing

5 Setting up of site office, Sheds & stores etc.

7 Concreting for

a)Structure Foundations

b)Equipment and mounting structure foundadions

c)Cable trenches

2. Installation

8 Receipt(at site) of

a)Main equipment / spares

c)Insulators & Hardwares

d)Clamps & Connectors

e)Marshalling kiosks

f)Cables & Cabling Materials

a)Main structures

b)Equipment support structures

10 Equipment Erection

12 Bus bar erection

15 Completion of testing and ready for commissioning

16 Commissioning

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE-11B : COMPLETION SCHEDULE FOR TRANSMISSION LINES

SHEET FOR TECHNOCOMMERCIAL OPENING

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Bidders Name and Address: To,

The Chief Engineer, Electy., Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore. - 560009.

We hereby declare that following shedules shall be followed by us for the above work. The period of various activities from the date of placement of award letter shall be as follows.

SL.NO Activity Period in months for work of Construction of Transmission Lines

Commencement Completion

1 Submission of Drawings

2 Completion of detailed engineering

3 Commencement of Manufacturing

4 Completion of Manufacturing

5 Readiness for testing

6 Readiness for Shipment

7 Receipt at Site

8 Completion of Shipment

1 Detailed Survey

2 Setting up of site office, sheds and stores etc.

3 Exacavation for foundations.

4 Foundations and other Civil Works

5 Erection of Tower alongwith accessories

6 Stringing of conductor/ groundwire alongwith accessories

7 Testing , Commissioning and Handing over.

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 12 TYPE TESTS & TEST CHARGES OF EQUIPMENT/MATERIALS

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

BIDDERS SHALL INDICATE VARIOUS TYPE TESTS IN LIGHT BLUE COLOURED CELLS

ALL THE TYPE TESTS APPLICABLE FOR EACH OF THE EQUIPMENTS SHALL BE INCLUDED.

Bidders Name and Address To,

The Chief Engineer, Electy., Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore. - 560009.

SL.No Details of Equipments Type Test Test Charges ( in Rs )

1 Power Transformer:

a) 20MVA, 66/11kV

2 SF6 Circuit Breakers:

4 Current Transformer:

5 Voltage Transformers:

6 Capacitive Voltage Transformers:

7 Surge Arrestors

8 a) Relay & Protection Panels

b) Substation Automation

9 L.T. A.C Panel

10 Station Battery

11 Station Battery Charger

12 PLCC Battery

13 PLCC Battery Charger

14 1.1KV Copper control cables/LT Power Cable

15 11KV U.G Cable

16 PLCC equipment

17 Conductors & Earth Wire a) Moose ACSR

c) Coyote conductor

d) Lynx conductor

e) Panther Conductor

18 Insulators a) 120/90KN Disc Insulator Strings

b) Solid Core Insulators

c) Silicon rubber/ Disc/ Long rod insulators

d) Post Insulators

19 Station / Mounting Structures/Lightning Mask

21 Hardware Materials

22 Aluminium pipe and Clamps

23 AC DISTRIBUTION BOX

24 DC DISTRIBUTION BOX

26 Nitrojen Fire Fighting Protection System

NOTE: The Type Test / Special Tests, if repeated at the insistance of owner, the applicable testing charges shall be paid by the successful Bidder upfront to the laboratory and the same shall be reimbursable by KPTCL as per actuals on submission of Bills along with proof of payment and on successful completion of all the Type Tests, specified and on approval of the same by the owner. In case equipment/material fails in the type tests during testing then the testing charges paid by the Bidder to the laboratory will not be reimbursed by KPTCL. The above Clause is applicable for all the equipments/materials, in case, the Type Test / Special Tests, are repeated at the insistance of owner(KPTCL).

Place Printed Name

Karnataka Power Transmission Corporation Limited

Schedule -13-List of Optional Spares

SHEET FOR TECHNOCOMMERCIAL OPENING

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

BIDDERS SHALL NOTE THAT QUANTITIES INDICATED IN THE PERCENTAGE FINANCIAL BID OFFER SHALL BE INDICATED HERE ALSO.

Bidders Name and Address

The Chief Engineer, Electy., Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore. - 560009.

List of optional spares required to meet the specified performance for a period of three years

Sl. No. For Equipments Details of item Unit Quantity

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE - 14-Guaranteed Losses :

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidders Name and Address along with GSTIN No.: To,

The Chief Engineer, Electy., Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore. - 560009.

Dear Sir, i) We Declare that the ratings and performance figures of the transformer furnished by us under the Turnkey Package are Guaranteed. We further declare that in the event of any deficiencies in meeting the guarantees in repect of the characteristics mentioned below as established after conducting the factory test, you may at your discretion,reject or accept the equipment after assessing the liquidated damages as specified in relevant clause of Bid Document.

Equipment Guaranteed Losses at rated output(KW)

Max No Load loss at rated voltage and rated frequency Max Load loss at rated current and frequency and at 75 deg C at principal tap Max I2 R loss at rated current and frequency and at 75 deg C at principal tap Max Auxiliary loss at rated voltage and frequency for Power Transformer

i) 20MVA, 66/11kV Power Transformer

Note:(i) Refer Technical Specifications (ii)The loss quoted shall be consistent in Schedule 14 and GTPs(DRS)of Power Transformer

Equipment Total Losses in KW / watts

i) 100KVA, 11KV/433V Auxiliary Transformer Note: Refer Technical Specifications , As per technical specifications, for 100 kVA, 11KV/433V Auxiliary Transformer: Maximum Losses should not exceed 1500 watts

Note: Refer Technical Specifications As per technical specifications, for 100 kVA, 11KV/433V Auxiliary Transformer: Maximum Losses should not exceed 1500 watts.

High Performance Conductor(HPC):

High Performance Conductor (HPC) for new Transmission Lines with new Towers/Supports

Sl.No. Parameters Guaranteed Values Remarks

i) Guaranteed Losses at Temperature corresponding to maximum operating Current of 700A (in kW/km)

ii) Rac ( AC Resistance Per KM guaranteed by the Bidder at maximum continuous operating temperature corresponding to specified continuous operating current of 700A) (in Ohms Per km)

iii) Guaranteed Maximum Continuous Operating Temperature (in Deg C)

iv) Rdc ( DC Resistance Per KM guaranteed by the Bidder at 20 deg C ) (in Ohms Per km)

High Performance Conductor(HPC):

High Performance Conductor (HPC) for existing Towers/Supports

Sl.No. Parameters Guaranteed Values Remarks

i) Guaranteed Losses at Temperature corresponding to maximum operating Current of 700A (in kW/km)

ii) Rac ( AC Resistance Per KM guaranteed by the Bidder at maximum continuous operating temperature corresponding to specified continuous operating current of 700A) (in Ohms Per km)

iii) Guaranteed Maximum Continuous Operating Temperature (in Deg C)

iv) Rdc ( DC Resistance Per KM guaranteed by the Bidder at 20 deg C ) (in Ohms Per km)

Note: The Technical particulars furnished in this Schedule shall be same as that of Technical particulars furnished in Data Requirement Sheets and GTPs uploaded as per Technical Specifications.

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

LIST OF VENDORS

SHEET FOR TECHNOCOMMERCIAL OPENING

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

BIDDERS NAME AND ADDRESS To, The Chief Engineer, Electy., Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore. - 560009.

Sl. No. EQUIPMENT/ MATERIAL NAME OF THE VENDOR

VENDOR 1 VENDOR 2 VENDOR 3 VENDOR 4

1 Power Transformer:

a) 20MVA, 66/11kV

2 SF6 Circuit Breakers:

4 Current Transformer:

5 Voltage Transformers:

6 Capacitive Voltage Transformers:

7 Surge Arrestors

8 a) Relay & Protection Panels

b) Substation Automation

9 L.T. A.C Panel

10 Station Battery

11 Station Battery Charger

12 PLCC Battery

13 PLCC Battery Charger

14 1.1KV Copper control cables/LT Power Cable

15 11KV U.G Cable

16 PLCC equipment

17 Conductors & Earth Wire a) Moose ACSR

c) Coyote conductor

d) Lynx conductor

e) Panther Conductor

18 Insulators a) 120/90KN Disc Insulator Strings

b) Solid Core Insulators

c) Silicon rubber/ Disc/ Long rod insulators

d) Post Insulators

19 Station / Mounting Structures/Lightning Mask

21 Hardware Materials

22 Aluminium pipe and Clamps

23 AC DISTRIBUTION BOX

24 DC DISTRIBUTION BOX

26 Nitrojen Fire Fighting Protection System

Place Printed Name

SCHEDULE-16 : NO DEVIATION CERTIFICATE (ANNEXURE-I)

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

NOTE: SCHEDULE DULY SIGNED BY THE AUTHORIZED PERSON SHALL BE UPLOADED

With reference to our Bid Proposal No dated

We hereby confirm that we have read the provisions of the contract, the stipulation of these clause are acceptable to us,

and we have not taken any deviation whatsoever to these clauses:

a) Terms of payment Clause No. 37 of Section-5,Conditions of Contract (CC) and Clause No.8 of Special Conditions of Contrac (SCC)

b) EMD/Bid Security Clause No. 6, Section :1, Invitation for Tenders (IFT) and Clause No. 13, Section :2, Instruction to Tenderer (ITT)

c) Contract Performance Guarantee Clause No. 29 of Section:2, Instruction to Tenderers (ITT).

d) Penalty for delay Clause No. 41 of Section-5 : Conditions of Contract (CC).

e) Price Basis/ Price adjustment Clause No. 40 of Section-5 :Conditions of Contract (CC).

f) Defects Liability Period/Guarantee Clause No. 10 of Section-5 Special Conditions of Contract (SCC)

g) Work Schedule Clause No.17 of Section:5 Conditions of Contract (CC)

h) Taxes and Duties Clause No. 11.11 of Section-2: Instruction to Tenderers (ITT).

We further confirm that any deviation to the above clauses at SI.No. (a) to (h) found anywhere in our bid proposal, implicit or explicit, shall stand unconditionally withdrawn, without any cost, implication whatsoever to KPTCL.

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE-17a FORM FOR BID SECURITY/EMD (ANNEXURE-IIA) (To be stamped on Rs.300/- Non-Judicial stamp paper in accordance with KPTCL Circular No. KPTCL/GMT/CIVIL (B7)/35/2024-MANAGER ESTATE (E-106992) dated 02.03.2024)

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

NOTE: SCHEDULE DULY SIGNED BY THE AUTHORIZED PERSON SHALL BE UPLOADED AND SENT ALONG WITH ORIGINAL BANK GUARANTEE AND ORIGINAL DD (TOWARDS BID GUARANTEE ) TO CHIEF ENGINEER ELECTRICIYT (T&P),KPTCL BANGALORE SO AS TO REACH AFTER THE LAST SUBMISSION DATE & ON OR BEFORE THE DATE & TIME OF OPENING TECHNO COMMERCIAL BIDS.

Ref No. Bank Guarantee No.

In accordance with Invitation to Bid under your specification

No. M/s having its Registered /

Head Office at (hereinafter called the 'Bidder') wish

to participate in the said Bid or and you, as a special favour have agreed

to accept an irrevocable and unconditional bank guarantee for an amount of

valid up to on behalf of Bidder in lieu of the Bid deposit required to be made

by the Bidder as a condition predecent for participation in the said Bid,in addition to the Demand draft No.

we the Bank at having our Head office at

(local address) guarantee and undertake to pay immediately on demand by Karnataka Power Transmission Corporation

the amount of (in figures and words)

without any reservation, protest, demur and recourse. Any such demand made by said `Owner' shall be conclusive and binding on us irrespective of any dispute or difference raised by the Bidder.

This Guarantee shall be irrevocable and shall remain valid up to and including

If any further extension of this guarantee is required, the same shall be extended to such required period (not exceeding one year) on receiving instructions

from M/s on whose behalf this guarantee is issued.

This Guarantee has been issued using SFMS Platform and the requisite communication in this regard has been forwarded to the Beneficiary Bank.

In witness whereof the Bank, through its authorised officer, has set its hand and stamp on this

Signature Signature

Official Addressess Designation with Bank Stamp.

Attorney as per Power of Attorney No.

Note : 1) Both the Bank Guarantee and Demand Draft shall be scanned and uploaded along with Electronic sheets. 2) This date shall be Forty Five (45) days after the last date for which the bid is valid.

Karnataka Power Transmission Corporation Limited

SCHEDULE-17b Form of Insurance Surety Bond towards EMD (ANNEXURE-IIB) (To be stamped on Rs.300/- Non-Judicial stamp paper in accordance with KPTCL Circular No. KPTCL/GMT/CIVIL (B7)/35/2024-MANAGER ESTATE (E-106992) dated 02.03.2024)

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Insurance Surety Bond No.

In accordance with Invitation for Bids under your Bid Document No

M/s having its Registered /

Head Office at (hereinafter called the 'Contractor') wish

to participate in the said Bid for

As an irrevocable Insurance Surety Bond against Bid Security for an amount of * valid for days from **

required to be submitted by the Contractor as a condition precedent for participation in the said bid which amount is liable to be forfeited on the happening of any contingencies as mentioned under the Bidding Documents.

we, the having our Head office at

guarantee and undertake to pay immediately on demand by Karnataka Power Transmission Corporation Limited, (hereinafter called the 'Owner') the amount of

without any reservation, protest, demand and recourse. Any such demand made by the 'Owner' shall be conclusive and binding on us irrespective

of any dispute or difference raised by the Contractor and/or any right/remedy available to the Contractor in terms thereof.

This Insurance Surety Bond shall be unconditional as well as irrevocable and shall remain valid upto

If any further extension of this Insurance Surety Bond is required, the same shall be extended to such required period (not exceeding one year) on receiving instructions from

M/s on whose behalf this Insurance Surety Bond is issued.

In witness where of the Insurer, through its authorised officer, has set its hand and stamp on this

Signature Signature

Official Addressess Designation with Insurer Stamp

Attorney as per Power of Attorney No.

NOTE: 1. (*) The amount shall be as specified in the SPC. (**) This shall be the last date of bid submission deadline. (@) This date shall be Forty Five (45) days after the last date for which the bid is valid 2. The Insurance Surety Bond shall be from an Insurer as per guidelines issued by Insurance Regulatory and Development Authority of India (IRDAI) as amended from time to time. 3. The Owner shall be the Creditor, the Contractor shall be the Principal debtor and the Insurance company/Insurer shall be the Surety in respect of the Insurance Surety Bond to be issued by the Insurer. 4. The Insurance Surety Bond should be on Non-Judicial stamp paper/e-stamp paper of appropriate value as per Stamp Act prevailing in the state(s) where the Insurance Surety Bond is submitted or is to be acted upon or the rate prevailing in State where the Insurance Surety Bond is executed, whichever is higher. The Stamp Paper/e- stamp paper shall be purchased in the name of Contractor /Insurer issuing the Insurance Surety Bond. 5. While getting the Insurance Surety Bond issued, Contractors are required to ensure compliance to the points mentioned in Form of Bank Guarantee/Insurance Surety Bond Verification Check List enclosed in this Section of Bidding Documents. Further, Contractors are required to fill up this Form and enclose the same with the Insurance Surety Bond.

Karnataka Power Transmission Corporation Limited

SCHEDULE-18 PROFORMA OF LETTER OF UNDERTAKINGS (ANNEXURE-V)

SHEET FOR TECHNOCOMMERCIAL OPENING

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

NOTE: SCHEDULE DULY SIGNED BY THE AUTHORIZED PERSON SHALL BE UPLOADED

(To be executed on Non-Judicial paper of RequisiteValue)

1. I*/We* have read and examined the following bid documents relating to the

(full Scope of Work)

a) Notice Inviitng Tender

b) Conditions of Contract containing section 'Invitation for Tenders’, 'Instructions to Tenderers’, ‘Conditions of Contract’ and Contract Data.

c) Special Conditions of Contract along with Annexure to

d) Drawings No.

e) Technical Specifications

2 . I / We hereby submit our Bid and undertake to keep our Bid Valid for a period of One Hundred and Eighty days (180 days) from the Last date of bid submission as notified (either original or extended). I*/We* hereby further undertake that during said period I/We shall not vary/alter or revoke my/our Bid.

This undertaking is in consideration of KPTCL agreeing to open my/ our Bid and consider and evaluate the same for the purpose of award of Work in terms of provisions of clause entitled "Award of Construct" 'cl.no. 26 of Section ITT and cl.no. 18 of SCC of the Bid Documents.

Should this bid be accepted, I*/We* also agree to abide by and fulfil all the terms, conditions of provision of the above mentioned bid.

Signature along with Seal of Co.

(Duly Authorised to sign the Tender on Behalf of the Contractor.)

NAME OF THE COMPANY (in Block Letters)

SIGNATURE Date and Postal Address

DATE Telegraphic Address

NAME AND ADDRESS Telephone No.

Karnataka Power Transmission Corporation Limited

SCHEDULE-19 CONSORTIUM AGREEMENT (To be stamped on Rs.500/- Non Judicial stamp paper in accordance with KPTCL Circular No. KPTCL/GMT/CIVIL(B7)/35/2024-MANAGER ESTATE (E-106992) dated 02.03.2024) (ANNEXURE -XIII)

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

NOTE: SCHEDULE DULY SIGNED BY THE AUTHORIZED PERSON SHALL BE UPLOADED.

CONSORTIUM AGREEMENT AMONGST M/s M/s

For Bid Specification No. OF KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

This consortium agreement executed on this day Month of Two thousand Twenty Three

amongst M/s a company incorporated under the laws of (Country) and having its registered office at

(hereinafter called the "Lead Company" which expression shall include its successors ,executors and permitted assigns),

M/s a company incorporated under the laws of (Country) and having its registered office at

(hereinafter called the "Constituent Company" which expressions shall include its successors,executors and permitted assigns)

for the purpose of making a bid and entering into a contract (In case of award) against the specification no.

For NAME OF THE WORK

for Karnataka Power Transmission Corporation Ltd. having its registered office at Indhana Bhavana , A.R Circle, Bangalore 560 009 , Karnataka (hereinafter called the "Owner"). The leader of the consortium shall abide by the general terms and conditions specified by the Purchaser. WHEREAS the Owner invited bids as per the above mentioned specifications for the design, manufacture, supply and erection, testing and commissioning of Equipments/Materials stipulated in the bidding documents under subject package

NAME OF THE WORK

AND WHEREAS Section-I ( Volume-1: Clause No. 11:- Qualifying Requirement), forming part of the bidding documents, stipulates that a consortium meeting the requirements of Section-I, ( Invitation of Bid) applicable may bid, provided the Consortium fulfills all other requirements of specification and in such a case, the Bid shall be signed by the members so as to legally bind the members and who will be jointly and severally liable to perform the Contract and all obligations hereunder.

The above clause further states that the consortium agreement shall be attached to the bid and the contract performance guarantee will be as per the format enclosed with the bidding document without any restriction or liability for either party.

AND WHEREAS the bid has been submitted to the Owner vide proposal No dated

by Lead Company based on the Constituent agreement between all the consortium under these presents and the bid in accordance with the requirements of Specifications (Qualification Requirements).

NOW THEREFORE THIS UNDERTAKING WITNESSETH AS UNDER:

In consideration of the above premises and agreements all the partners to this consortium members do hereby now agree as follows:

1 In Consideration of the award of the Contract by the Owner to the Consortium members, we , the members to the consortium agreement do hereby agree that M/s

shall act as Lead Company and further declare and confirm that we shall jointly and severally be bound up to the Owner for the successful performance of the contract and shall be fully responsible for the design, manufacture, supply and successful performance of the equipments in accordance with the Contract.

2 In case of any breach of the said contract by the Lead company or other constituent of the Consortium agreement, the Lead company do hereby agree to be fully responsible for the successful performance of the contract and to carryout all the obligations and responsibilities under the contract in accordance with the requirements of the Contract

3 Further, if the Owner suffers any loss or damage on account of any breach in the contract or any shortfall in the performance of the equipment in meeting the performance guaranteed as per the specification in terms of the contract, the Lead company of these presents undertake to promptly make good such loss or damages caused to the Owner, on its demand without any demur. It shall not be necessary or obligatory for the Owner to proceed against Lead Partner to these presents before proceeding against or dealing with the other Partner (s).

4 The Financial liability of the members of the consortium agreement to the Owner, with respect to any of the claims arising out of performance or non-performance of the obligations set forth in the said agreement, read in conjunction with the relevant conditions of the contract shall, however not be limited in any way so as to restrict or limit the liabilities of any of the members of the agreement.

5 It is expressly understood and agreed between the members to this consortium agreement that the responsibilities and obligations of each of the partners shall be as delineated hereunder (To be incorporated suitably by the member to this agreement). However, each member of the consortium will be severally and jointly responsible for the faithful performance of the contract. It is further agreed by the member that the above sharing of responsibilities and obligations shall not in any way be a limitation of joint and several responsibilities of the members under this contract.

Sl.No. Name of the Lead Bidder/Consortium Partner. Scope of the work/Participation

We further declare ourselves bound to execute our scope of work/participation as stated above;

6 This Consortium agreement shall be constructed and interpreted in accordance with the laws of India and the courts of Bangalore shall have the exclusive jurisdiction in all matters arising there under.

7 In case of an award of a Contract, we the Consortium members do hereby agree that we shall be jointly & severally responsible for the works respectively executed and Lead company shall furnishing a contract performance security from a bank in favor of the PURCHASER in the forms acceptable to purchaser for value of Five percent (5%) of the Amount put to tender (Excluding GST) plus additional security for unbalanced tenders in accordance with Clause 25.5 & 29 of ITT and Clause 43 of the CC (Conditions of Contract).

8 It is further agreed that the Consortium agreement shall be irrevocable and shall form an integral part of the contract, and shall continue to be enforceable till the owner discharges the same. It shall be effective from the date first mentioned above for all purposes and intents.

IN WITNESS WHEREOF the partners to the Consortium have through their authorized representatives executed these presents and affixed Common seals of their companies, on the day, month and year first mentioned above.

WITNESS for Lead Company

(Signature) (Signature of the authorized representative)

(Name in Block Letters) (Name)

Designation (Designation)

Common Seal of the Company

2 ( For Constituent 1)

(Signature of the authorized representative)

(Name in Block Letters) (Name)

Designation Common Seal of the Company

Karnataka Power Transmission Corporation Limited

SCHEDULE-20(a) POWER OF ATTORNEY (ANNEXURE-XI)

(For Individual Bidder / Lead Partner of Consortium)

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

NOTE: SCHEDULE DULY SIGNED BY THE AUTHORIZED PERSON SHALL BE UPLOADED.

POWER OF ATTORNEY

KNOW ALL MEN BY THESE PRESENTS that we

a Company incorporated

under the laws of

and having its Registered Office / Head Office at

"Manufacturer / Bidder" which expression shall unless repugnant to the

Context or meanig thereof, include its successors, administrators and assigns)

acting through Mr its constitute, nominate and appoint

M/s a Company incorporated under the laws of

and having its Registered / Head Office at

as its duly constituted lawful Attorney (hereinafter called "Attorney"

or "Authorized Representative") to exercise all or any of the powers for and on

behalf of the "Manufacturer / Bidder" in regard to Specification No.

the bids for which have been invited by

(Address "Owner") to undertake the following acts:

i. To submit proposal and participate in the aforesaid Bid Specification of the Owner on behalf of the "Manufacturer / Bidder".

ii. To negotiate with the "Owner" the terms and conditions including price for award of the contract pursuant to the aforesaid Bid and to sign the contract with the "Owner" for and on behalf of the Manufacturer / Bidder.

iii. To receive accept and execute the contract for and on behalf of the "Manufacturer / Bidder".

iv. To do any other act or submit any document related to the above.

It is expressly understood that the Power of Attorney shall remain valid, binding and irrecoverable till submission of the Contract performance guarantee in terms of the Contract. The "Manufacturer / Bidder" hereby agrees and undertakes to ratify and confirm all the whatsoever the said "Attorney" / "Authorised Representative" quotes in the Bid, negotiates and signs the contract with the "Owner" and / or purports to act on behalf of the "Manufacturer / Bidder" by virtue of this Power of Attorney and the same shall bind the "Manufacturer / Bidder" as if done by itself.

IN WITNESS WHEREOF THE "Manufacturer / Bidder" has executed these presents at

on this day of under

the Common Seal of the Manufacturer company / Bidder.

Specimen Signature of Attorney Holder

(Name & Designation)

For and on behalf of

Common Seal of the above Manufacturer/Bidder

Has been affixed thereto in the presence of :

Karnataka Power Transmission Corporation Limited

SCHEDULE-20(b) POWER OF ATTORNEY (ANNEXURE-XV)

(FOR CONSORTIUM MEMBER)

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

NOTE: SCHEDULE DULY SIGNED BY THE AUTHORIZED PERSON SHALL BE UPLOADED

POWER OF ATTORNEY

(To be stamped on Rs.500/- Non Judicial stamp paper in accordance with KPTCL Circular No. KPTCL/GMT/CIVIL (B7)/35/2024-MANAGER ESTATE (E-106992) dated 02.03.2024)

KNOW ALL MEN BY THESE PRESENTS that we

a Company incorporated

under the laws of

and having its Registered Office / Head Office at

"Manufacturer / Bidder" which expression shall unless repugnant to the

Context or meanig thereof, include its successors, administrators and assigns)

acting through Mr its constitute, nominate and appoint

M/s a Company incorporated under the laws of

and having its Registered / Head Office at

as its duly constituted lawful Attorney (hereinafter called "Attorney"

or "Authorized Representative") to exercise all or any of the powers for and on

behalf of the "Manufacturer / Bidder" in regard to Specification No.

the bids for which have been invited by

(Address "Owner") to undertake the following acts:

i. To submit proposal and participate in the aforesaid Bid Specification of the Owner on behalf of the "Manufacturer / Bidder".

ii. To negotiate with the "Owner" the terms and conditions including price for award of the contract pursuant to the aforesaid Bid and to sign the contract with the "Owner" for and on behalf of the Manufacturer / Bidder.

iii. To receive accept and execute the contract for and on behalf of the "Manufacturer / Bidder".

iv. To do any other act or submit any document related to the above.

It is expressly understood that the Power of Attorney shall remain valid, binding and irrecoverable till submission of the Contract performance guarantee in terms of the Contract. The "Manufacturer / Bidder" hereby agrees and undertakes to ratify and confirm all the whatsoever the said "Attorney" / "Authorised Representative" quotes in the Bid, negotiates and signs the contract with the "Owner" and / or purports to act on behalf of the "Manufacturer / Bidder" by virtue of this Power of Attorney and the same shall bind the "Manufacturer / Bidder" as if done by itself.

IN WITNESS WHEREOF THE "Manufacturer / Bidder" has executed these presents at

on this day of under

the Common Seal of the Manufacturer company / Bidder.

Specimen Signature of Attorney Holder

(Name & Designation)

For and on behalf of

Common Seal of the above Manufacturer/Bidder

Has been affixed thereto in the presence of :

Karnataka Power Transmission Corporation Limited

SHEET FOR TECHNOCOMMERCIAL OPENING (UN - PRICED)

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

Bidders Name and Address

To, The Chief Engineer, Electricity, Tendering & Procurement, KPTCL, Bangalore - 09.

We Declare that the ratings and performance figures of the equipment furnished by us under the Turnkey Package are Guaranteed. We further declare that in the event of any deficiencies in meeting the guarantees in repect of the characteristics as established after conducting the performance test, you may at your discretion, reject the equipment, in which case we shall replace the same with equipment as per specification and meeting the guarantee, free of charge and within a resonable time, to be mutually agreed.

Place Designation

Name of the Company

KARNATAKA POWER TRANSMISSION CORPORATION LIMITED

SCHEDULE -22 - Check List

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

BIDDERS NAME AND ADDRESS To,

The Chief Engineer, Electy., Tendering & Procurement, KPTCL,9th Floor, Indhavana Bhavan, A.R Circle, Bangalore. - 560009.

CHECK LIST FOR SUBMISSION OF SCHEDULES

REFERENCE OF FORM & SCHEDULE DETAILS OF FORM & SCHEDULE WHETHER INCLUDED IN TECHNO-COMMERCIAL SHEETS (ELECTRONIC) YES/NO WHETHER INCLUDED IN PERCENTAGE RATE Financial Offer (ELECTRONIC) YES/NO WHETHER INCLUDED IN COMMERCIAL

PROPOSAL BID PROPOSAL

Schedule - 1 PRICE COMPONENTS

Schedule 2 (1 of 2 & 2 of 2) Summary of Price Components

Schedule 2A Schedule of Discounts

Schedule 2B Statement of Commercial Terms & Conditions

Schedule 3A & 3B Price break up for supply & erection

Schedule 3C Price break up for civil works

Schedule 4 Price break up for mandatory spares and maintenance & Testing Equipments.

Schedule 5 Commercial deviations

Schedule 6 Technical deviations

Schedule 7 List of special Tools & Tackles

Schedule 8 Additional information.

Schedule 9 Qualification Information [Technical & Financial]

Schedule 10 Details of Tools and plants and man power deployment

Schedule 11 A & 11B Schedule for activities & Commissioning.

Schedule 12 Type Test Charges

Schedule 13 List of optional spares and cost.

Schedule 14 Guaranteed loss of transformer.

Schedule 15 List of vendors.

Schedule 16 Annexure 'A' No deviation certificate

Schedule 17a & 17b Proforma for Bid guarantee

Schedule 18 Proforma for letter of undertaking

Schedule 19 Consortium Agreement

Schedule 20a & 20b Power of attorney for Individual Bidder / Lead Partner of Consortium and Consortium Member

Schedule 21 Guaranteed Declaration

Schedule 22 Check list

DRS 1-45 Relevant Technical details for Materials / Equipments

To be Uploaded Contract Quality Assurance Programme

To be Uploaded Type Test Certificates

To be Uploaded & furnished Bid Security/EMD

To be Uploaded Written Power of Attorney

To be Uploaded Letter of Undertaking

To be Uploaded No Deviation Certificate

To be Uploaded Any Other (Please Specify)

To be Uploaded Any Other (Please Specify)

To be Uploaded Any Other (Please Specify)

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

Bid Enquiry Number:KPTCL/2025-26/SS/WORK_INDENT/3498

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

A1 : GUARANTEED TECHNICAL PARTICULARS FOR POWER TRANSFORMERS

(Bidder should indicate the guaranteed technical data of all equipments/materials for each type of rating separately)

Class of Power Transformer 20 MVA, 66/11kV Power Transformer

1 Name of the Manufacturer and country of origin

2 Reference standard

3 Service [Indoor/outdoor]

4 Continuous rating under service conditions specified in IS-2026 Part-I, 2011 Clause No.1.1 : HV

a. 1. With ONAN cooling - MVA

2. With ONAF cooling - MVA

b. Rated no load voltage

6 a. Rated Frequency : (Hz)

b. Number of phases

7 Current at rated voltage and on principal tap-Amp :HV

8 Maximum hot spot temperature rise calculated by formula 0C over the maximum yearly weighted average ambient temperature

9 Flux density at rated voltage and rated frequency in tesla

10 Temperature rise of top oil, oC by the thermometer (above Max. Ambient Temperature).

11 Temperature rise of winding measured by resistance (above Max. Ambient Temperature).

i. With ONAN cooling oC

ii. With ONAF cooling oC

iii. Period of operation of transformer at full load without calculated winding hot spot temperature exceeding 140oC and when

50% coolers fail

100% coolers fail [Refer Cl. No. 1.2.0.1]

12 No. of windings

13 Connections HV

14 Connection Symbol and vector group

i. Type of tap changer

ii. Tap step (percent)

iii. Total tap range (+) percent to (-) percent

iv. Tappings provided at

v. Type of regulation :

Constant flux regulation

Variable flux regulation

Combined regulation

vi)Insulation level of tap changer

16(A) Magnetization data at no load, at rated frequency

i. Current in Amps

ii. Power factor

iii. Loss in KW (core loss + dielectric loss)

iv. Max. flux density in lines/sq.cm.

a At 90% rated no load voltage

b At 100% rated no load voltage

c At 110% rated no load voltage

d At maximum rated primary voltage (i.e. 105% rated no load voltage)

16(B) i) Max. No-load loss at rated frequency at Principal Tap (KW) 0

ii) Max. No-Load loss at voltage corresponding to the Highest Tap (KW)

17(A) Max.load loss in KW at rated current and at 750C At Lowest Tap At Principal Tap At Highest Tap

a. For ONAN rating KW

b. For ONAF rating in KW 0

c. For OFAF rating in KW

Max. I2 R loss in KW at rated current and at 75◦C

a. For ONAN rating in KW

b. For ONAF rating in KW 0

c. For OFAF rating in KW

17(B) Max. Auxiliary loss at rated voltage and frequency. 0

Note for Sl. No. 16 & 17: Guaranteed values of the losses shall be indicated which shall be firm & without indicating the tolerance limit

18 Impedance at rated current and frequency at 75oC winding temperature on rated MVA base. HV to LV

i. At normal tap in %

ii. At max. voltage tap in %

iii. At min. voltage tap in %

19 Reactance at rated current and frequency and normal tap on rated MVA base:

HV to LV - in %

20 Zero sequence impedance at reference temperature of 75oC at principal tap ………in %

21 Resistance at 75 oC

HV winding in Ohms in %

LV winding in Ohms in %

22 Efficiency at 75oC winding temperature as derived from guaranteed. loss figures At Unity p.f At 0.8 p.f

a. At 125% full load

b. At 100% full load

c. At 75% full load

d. At 50% full load

23 a. Maximum efficiency ………in %

b. Load at which maximum efficiency occurs (% of full load)

24 Regulation at full load and at 75oC

a. At unity p.f. in %

b. At 0.8 p.f. (lag) in %

25 a. Short time thermal rating of LV winding in KA & duration in seconds.

b. Short time thermal rating of HV winding in KA & duration in seconds.

26 Permissible overloading - HV

27 Test voltages HV LV

i. Lighting impulse withstand kV (peak)

ii. Power frequency voltage withstand kV (ms)

iii. Switching impulse withstand kV (peak)

28 Partial discharge level at 1.5Um / √3 kVrms (pC)

29 RIV at 1.1 times minimum phase to ground voltage

31 Noise level when energized at normal voltage and normal frequency at no load (db)

32 External short circuit withstand capacity (MVA) & duration (seconds)

33 Over flux withstand capability of the transformer :

34 Insulating and cooling medium

35 Approximate weights

a. Core with clamping (Kg)

b. Winding with insulation (Kg)

c. Core & Winding (Kg)

d. Tank & Fittings with accessories (Kg)

e. Oil required for first filling (Kg)

f. Untanking weight (Kg)

g. Total weight with oil weight & fitting (Kg)

h. Weight of total insulation (Kg)

36 Required quantity of oil in litres

37 Terminal arrangement

ADDITIONAL TECHNICAL PARTICULARS:

1 Details of Core (along with Tolerance if any):

a. Type of core configuration

b. Type of core joints

c. Flux density at 90% of rated voltage and frequency at Principal Tap Tesla :

d. Flux density at 110% of rated voltage and frequency at Principal Tap Tesla :

e. (i) Material of core lamination

(ii) Thickness of core lamination (mm)

f. Approximate core weight (please indicate core weight only)

g. Type of Joints used between core limb and yoke

2 Details of Windings:

a. Conductor area in sq.cm and current density in Amps/Sq.cm (at rated current). Current density A/sq. cm Conductor area sq.cm

b. Material of winding conductor

c. Approximate weight of winding (along with tolerance if any)in kgs

d. Type of windings

e. Winding insulation Type and class Graded or ungraded

f. i. Insulating material used for :

1. Regulating winding

3. HV TAP WINDING

ii. Between HV and TAP WDG and LV as applicable

iii. Between core & LV side.

iv. For core bolts, washers and end plates

v. Regulating winding & earth.

g. i. Type of axial coil support

ii. Type of Radial coil support :

h. Core bolt insulation voltage

i. Details of special arrangement provided to improve surge voltage distribution in the windings

j. Approximate weight of winding (Kgs) (Tolerance if any on the above)

k. Minimum clearance (mm) In oil In Air

Between Phases Phase to ground Between Phases Phase to ground

3 Details of Tank :

a. Material for Transformer Tank

b. Type of the tank

c. Minimum thickness of sheet

ii. Bottom (mm)

iii. Cover (mm)

iv. Cooling tubes/Radiators (mm)

d. Vacuum recommended for hot oil circulation (torr)

e. Vacuum to be maintained during oil filling in transformer tank (torr)

f. Vacuum to which the tank can be subjected without distortion (torr)

Transverse Axis Longitudinal Axis

g. No. & size of bi-directional wheels provided.

h. (i) Track gauge required for the wheels-longitudinal axis & transverse axis

(ii) Size of rail recommended for the track

4 Details of painting at works and site

5 (a) Minimum clear height for lifting tank cover and for lifting core & windings from tank (mm) (untanking height).

(b) Minimum clear height for lifting (mm)

II. Bushings - HV

6 Shipping details :

i. Parts detached for transport

ii. Weight of heaviest package in Kgs

iii. Weight of other heavy packages in Kgs

iv. Dimensions of largest package

a. Length in mm

b. Breadth in mm

c. Height in mm

v. Dimensions of other heavy packages:

a. Length in mm

b. Breadth in mm

c. Height in mm

vi. Transformer will be transported with oil / gas

7 Details of Bushings HV LV

b. Rated voltage class - KV

c. Rated current - Amps

d. One minute dry withstand power frequency voltage - kV (ms)

e. One minute wet withstand power frequency voltage - kV (ms)

f. (i) 1.2 / 50 micro sec. Lighting impulse withstand voltage - kV (Peak)

(ii) Switching surge withstand test voltage kV (peak)

g. (a) Creepage Distance in air

(b) Creepage Distance (protected)

h. Quantity of oil in bushing and specification of oil used (Kgs)

i. Whether test tap is provided

j. Weight of assembled bushing

k. Phase to earth clearance in air of live parts at the top of bushing.

l. Minimum clearance (mm) In Air

Between phases Phase to ground

m. Partial discharge level

8 Cooling system

a. Grade of oil

b. Total weight of oil in radiator in Kgs/litres

c. Total weight of radiator without oil in Kgs.

d. Total radiating surface in square meters

e. Method of drying out transformer at site

f. Type and make of material used for the radiators with size.

g. Type of radiator

h. Total number of Radiators/Banks for transformer and over all dimensions (LxBxH)

i. Rating of Transformer with one radiator bank out of service.

j. Total weight of radiators in Kgs

k. Type of mounting

l. Vacuum withstand capability

9 Cooling equipment Fan Motor Pump Motor

a. Make and Type (Details)

b. Number of connected units (nos.)

c. Number of standby units (nos.)

d. Rated Power (KW)

e. BHP of driven equipment

f. Capacity (cu m/min) or (Litres/Minute)

g. Rated voltage (Volts)

h. Locked rotor current (Amps)

i. Temperature range for which control is adjustable

j. Efficiency of motor at full load (percent)

k. Temp. rise of motor at full load (oC)

l. Whether the fan and/or pumps suitable for continuous operation at 85% of their rated voltage

m. Estimated time constant in hours for

i. Natural cooling

ii. Forced air cooling

10 On Load Tap Changing gear (should be SCADA Compatible)

c. Power flow (uni-directional or bi-directional or restricted bi-directional)

d. Rated voltage to Earth kV

e. Rated maximum current Amps

f. Step voltage V.

g. Number of steps

h. Control : Manual / Auto / Local/Remote/Independent / Parallel.

i. Auxiliary supply details

j. Voltage control (whether automatic or manual)

k. Line drop compensation Provided / Not provided.

l. Protective devices

m. Time for complete tap change (one step) sec.

n. Divertor selector switch Transient time - Cycles.

o. Value of maximum short circuit current Amps.

p. Maximum impulse withstand test voltage with 1.2/50 micro seconds full wave between switch assembly and earth (kV peak)

q. Maximum power frequency test voltage between switch assembly and earth - kV rms.

r. Maximum impulse withstand test voltage with 1.2/50 micro seconds across the tapping range (kV peak).

s. Approximate over all dimensions of Tap changer mm

t. Approximate over all weight Kgs.

u. Approximate over all quantity of oil-ltrs/Kgs.

v. Particulars of the OLTC control panel for installation in the control room.

w. OLTC Routine test shall be conducted on each Transformers.

i) Mechanical Endurance Test (Min. 1000 operations)

ii) Sequence Test

iii) Pressure Test

iv) Vacuum (Helium) Test

v) Auxiliary Circuit Insulation test

x. OLTC Drive Mechanism Box: Make & Type

11 Over all dimensions of transformer including cooling gear, tap changing gear etc.

d. Reference drawing No.

12 Whether oil temperature indicator provided (Yes/No).

13 (a) Type of oil level indicator

(b) whether supervisory alarm contact for low oil level provided (Yes/No)

14 Type and size of Gas operated relay and whether supervisory alarm and trip contacts provided and their size and Nos.

15 Temperature indicators Oil Temp. indicator Winding temp. indicator

a. Make and Type

b. Permissible setting ranges for alarm & trip.

c. No. of contact

d. Current rating of each contact

e. Whether remote indicator provided, if, so, whether equipment required at purchaser's control room is included.

f. Size and No.

16 Ratio and Type of CT used for winding temperature

17 Type and size of Thermostat used

For Tr. Tank OLTC

18 No. of Breathers provided (No.)

19 Type of dehydrating agent used for breathers

20 a. Capacity of conservator vessel litres

b. Volume between the highest and lowest visible oil level (litres)

21 Valve sizes and number required/ fitted

i. Drain valves - mm - No.

ii. Filter valves - mm - No.

iii. Sampling valves - mm - No.

22 a. Type and make of pressure relief device

b. No. of each type of devices per transformer unit (Nos.)

c. Minimum pressure at which the device operates (Kpa)

23 Lifting jacks

a. Governing standard

b. No. of jacks in one set

d. Capacity (tonnes)

g.Height in closed position (mm)

h.Mean diameter of thread (mm)

24 Characteristics of Insulating oil to be used

Viscosity at 40 ºC in mm²/s

Viscosity at -30 ºC in mm²/s

Pour point in ºC

Water content in mg/kg

Breakdown voltage in kV

Density at 20 ºC in g/ml

Particle content

2 – Refining/stability

Acidity in mg KOH/g

Interfacial tension in mN/m

Total sulphur content

Corrosive sulphur

Potentially corrosive sulphur

Inhibitors of IEC 60666 in %

Metal passivator additives of IEC 60666 in mg/kg

Other additives

2- Furfural and related compounds content in mg/kg

3 - Performance

Oxidation stability for uninhibited oil – 164 hrs

Total acidity in mg KOH/g

Gassing tendency

4 – Health, safety and environment (HSE)

Flash point in ºC

PCA content in %

PCB content in mg/kg

5 – N-dm Analysis

6. Details of oil preserving equipment offered.

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

GUARANTEED TECHNICAL PARTICULARS FOR RELAY & PROTECTION PANELS

(Bidder should indicate the guaranteed technical data of all equipments / materials for each type of rating separately)

Relay & Protection Panels

Sl. No. Description

I Description, Construction & formation details :

1 Make and Type reference of manufacturer

i) type of construction.(duplex or simplex)

ii) type of scheme ( numerical type or static type)

b) for power transformer

3 Thickness of sheet steel (mm):

i. Door, Top and Bottom of panel

4 Tentative overall dimensions (L*B *H) (mm) of each panel

5 Dead weight of each panel (Kgs)

6 Approximate weight of each panel with all components (Kgs)

7 Details of packing for transport

8 Overall dimensions of transport package (L*B*H) (mm)

9 Approximate gross weight of transport package (Kgs)

10 Exterior paint film thickness (microns) and paint colour

11 Interior paint film thickness (microns) and paint colour

12 Cubicle Lighting : Volts, wattage, Type of holder and fitting whether provided with door control switch or not.

13 Safety earthing :

a. Material of conductor

b. Size (W*T) (mm)

c. Surface treatment and finish of conductor.

d. Type of end connection

14 Panel front/rear component identity board

c. Size of lettering and colour

d. Method of fixing

15 Panel wiring :

a. Type and material of wire conductors, insulation and voltage grade.

b. Conductor cross sectional area or strands/gauge of wire and colour scheme adopted for :

i. VT secondary circuits and annunciation circuit.

ii. Other Circuits.

c. Type of wire termination

16 Mimic bus details :

a. Type painted / strip fixed

c. Whether colour scheme specified will be followed

d. If not specify deviations.

II. TERMINAL BLOCKS AND CONNECTORS (USED FOR PANEL WIRING)

1 Make and Type reference of manufacturer

2 Insulation and voltage grade

3 Constructional details

4 Current rating of studs, size and material

5 Whether shrouding provided or not

6 Whether space terminals provided or not

7 Literature enclosed.

III. INDICATING LAMPS :

1 Wattage and voltage of lamp

2 Size of lens and material thereof

3 Type of lamp holder

4 Whether provided with series resistor? If yes, specify Ohmic value power loss

IV FUSE HOLDERS AND FUSES :

1 Make and Type reference of manufacturer

2 Insulation and voltage grade

3 Type of Insulation material

4 Type of fuses

5 Rating of fuses provided for different circuits

6 Literature enclosed.

VI. SELECTOR SWITCHES :

1 Make and Type reference of manufacturer

2 Type of handle / Switch

3 Mounting details

4 Number of positions

5 Number of contracts available in each position.

6 Making capacity of contacts

7 Breaking capacity of contacts

8 Whether locking arrangement is available.

9 Whether detailed literature and drawings encolsed. (YES/NO)

VII. PUSH BUTTONS :

1 Make and Type reference of manufacturer

2 Mounting details

3 Type of contact

4 Current and voltage rating

5 No. of contacts

6 Whether shrouding provided to prevent inadvertent operation (YES/NO)

7 Whether provided with integral engraved inscription plates (YES/NO)

VIII AUXILIARY CT's VT'S :

1 Make and Type reference of manufacture

b. Ratios available

d. Standard to which it conforms

e. Accuracy class

f. Short time current / voltage rating

g. Temperature rise

h. One minute power frequency withstand voltage

j. Mounting dimensional details

k. Panel in which to be provided with quantity thereof and connected ratio

3 For CT's only

a. Knee point voltage (KPV) (Volts)

b. Excitation current at KPV and 50% KPV (ma)

c. Internal impedance of primary and secondary windings in ohms

4 Literature enclosed.

IX. SPACE HEATERS :

1 Make and Type reference of manufacture

2 Type of space heater (Tubular / strip type)

3 Rating Wattage

4 Whether thermostat provided (YES/NO)

II INSTRUMENT TEST TERMINAL BLOCKS :

1 Make and Type reference of manufacturer

2 Insulation class and rating

3 Size and mounting details

4 Type of CT terminal shorting mechanism (LINK / SCREW)

5 Type of VT terminal Isolating Mechanism

6 Whether detailed literatures enclosed. (YES/NO)

C GENERAL PROTECTION RELAYS :

I The tenderer shall furnish guaranteed Technical particulars for all types of meters offered, in the following proforma (separate sheet shall be enclosed for each type of relay :)

1 Manufacturer's name or trade marks

2 Type designation

3 Size and mounting details (whether in draw out case)

4 Rated Values of both input and auxiliary energizing quantities

5 Values of the limits of the operative range(s) of the auxiliary energising quantity (ies)

6 Contacts data, Number and rating of main and auxiliary contacts

7 Rated value or setting range of the characteristic quantities and or angle

8 Limiting short-time thermal withstand values

9 Limiting dynamic values.

10 i. Burden data ( in case of poly input relays - data shall be furnished for appropriate set of input terminals).

a. At highest tap - AC current / voltage coil

b. At lowest tap - AC current / voltage (coil)

ii. DC power consumption.

11 Impulse and dielectric test voltage(s)

12 Details of accessories (If essential to the relay performance)

13 Details of accessories (Optional items)

14 Whether provided with seal in trip contacts

15 a. Type of operating characteristics

b. Accuracy of operating characteristics, operating time with details

16 H.F. disturbance test voltage (s)

17 Whether literature enclosed

18 Type of relay flag indicator and rating of target coil

II In addition to the above details, the following details shall also be furnished for relays specified below :

1 DOCR / DEFR :

a. Directional sensitivity

b. Minimum voltage at which the directional units operate

c. Characteristic angle

2 OVER FLUXING RELAY :

a. Whether provided with timer if so time setting available for Alarm and delayed trip.

3 Distance Protection Scheme for 220KV / 110KV / 66KV Lines:

A Type of distance measuring element

a. Starting unit

i. Type of scheme

b, No. of measuring element or comparator with details

c. Setting range of the distance measurement

d. No. of zones

i. Overall range for all zones.

ii. Reach setting range at rated current.

Zone - 1 (forward) - ohms

Zone - 2 (forward) - ohms

Zone - 3 (forward) - ohms

Off set zone 3 reverse - ohms

Zone extension (if any)

e. Characteristic of each zone

Phase fault unit

Earth fault unit

Phase fault unit

Earth fault unit

Phase fault unit

Earth fault unit

Zone - 3 off set

Zone -1 in ohms

1. Reach of the relay along with characteristic angle at rated current and voltage

2. Reach of the relay in resistive direction at rated current & voltage

3. Reach in reactive direction at rated current & voltage

Zone - 2 in ohms

1. Reach of the relay along with characteristic angle at rated current and voltage

2. Reach of the relay in resistive direction at rated current & voltage

3. Reach in reactive direction at rated current & voltage

Zone - 3 in ohms

1. Reach of the relay along with characteristic angle at rated current and voltage

2. Reach of the relay in resistive direction at rated current & voltage

3. Reach in reactive direction at rated current & voltage

Zone - 3 in Reverse ohms

1. Reach of the relay along with characteristic angle at rated current and voltage

2. Reach of the relay in resistive direction at rated current & voltage

3. Reach in reactive direction at rated current & voltage

f. Power swing blocking characteristic setting

i. Forward reach

ii. Reverse reach

g. Setting range of residual compensation

h. Setting range of mutual compensation

i. (i) Operating time

(ii) Time setting range

Power swing blocking

Zone - 1 (reach)

Zone - 2 (reach)

Zone - 3 (forward reach)

K. Polarising scheme

B. Additional featues provided :

a. Fault locator

b. Carrier aided tripping scheme

c. Power swing blocking

d. Broken conductor detection

e. Synchronous check

f. Weakend infeed

g. Switch on to fault

h. Fuse failure supervision

C. Facilities available for Fault Locator

a. Name and type reference of manufacturer

b. Rating and setting available

c. Rated V A burden

d. Power consumption voltage and current element

e. Memory capacity with details

f. Triggering method

h. Method of accuracy

D Auto Recloser:

a) Reclosing facilities available b) Single phase/three phase dead time range. c) Reclaim time range d) No. of modes selectable by selection switch e) Provision of Check synchronizing features and its time setting, range phase angle setting, voltage difference setting. f) Provision of deadline charging set range of voltage. g) Lock out facility.

E Disturbance Recorder:

a) No. of event channels b) No. of analog signals. c) Sampling rate d) Recording Band width e) Over current triggering – range. f) Under current triggering – range. g) Over voltage triggering – range. h) Pre fault time – range. i) Post fault time – range. j) Limit time – range. k) No. of recorded disturbances. l) Total recording time with 8 Analog and 16 event channels recorder. m) Voltage channels – details. n) Period of built in calendar. o) Current channels – details,

F EVENT RECORDER

a) Time tagging resolution. b) Events capacity i) Max. NO. of events per disturbance report. ii) Max. No. of disturbance reports

c) Time tagging error with synchronization. i) Once in One second ii) Once in ten seconds. iii) Once in sixty seconds

d) Timer tagging error without synchronization.

4 Restricted Earth fault Relay.

a) Manufacturer Type P designation

b) Operating time 2 x setting

5 Differential protection scheme :

a. No. of restraining coils and operating coils.

b. Harmonic restraints provided with details

c. Rated VA Burden and power consumption of

i. Restraining coil

ii. Operating coil

d. Type of slope setting :

If variable, range of slope setting through fault current stability. Maximum & minimum range of HV / MV / LV current ratio over which the relay can be used.

e. Whether provided with switching inrush current restraint, if so type.

6 Trip circuit supervision relay:

a) Name of manufacturer.

b) Type & Designation.

c) Whether preclosing & post closing supervision provided.

7 High speed trip relay

a) Name of manufacturer.

b) Type & Designation.

c) Contact rating.

Current rating-

i) Continuous rating

ii) Rating for 5 secs.

d) Break Resistive load inductive load (with L/R = 40 msec.

e) Operating time at rated voltage (max).

f) Resetting time.

g) Whether supervisory relay included.

8 Local breaker back up protection.

a) Name of manufacturer.

b) Type & Designation.

c) Operating time

d) Resetting time

e) Setting range

9 Bus bar protection

a) Name of manufacturer.

b) Type & Designation.

c) Type of relay (numerical)

d) Principle of operation (biased/low impedance)

e) Operating time

f) Resetting time

g) Setting range.

h) Whether will it cause tripping for the differential current below the load current of heavily loaded feeder (Bidder shall submit application check for the same).

III The tenderer shall confirm whether the following details will be furnished at the time of approval of drawings:

a. Identification and location of removable parts.

b. Data of permit suitable connection of the relay (including the polarity)

c. Data concerning the earthing of metallic part

d. To indicate parts of modules which should not be replaced without observing precaution prescribed by the manufacturer.

GUARANTEED TECHNICAL PARTICULARS FOR ELECTRONIC TRIVECTOR METERS

Sl. No. PARTICULARS

1 Type of Meter

2 Class of Accuracy

3 Standard to which the meter conforms

4 Current rating for which accuracy is guaranteed for

a. Basic Current (ib)

b. Continuous Current overloading capability

c. Short time over current

d. Minimum Starting Current

5 a)Voltage rating for which accuracy is guaranteed for

b)Over voltage withstand capacity - continuous

c)Voltage Range

6 Other Parameters for which accuracy is guaranteed

a. Reference Temperature

b. Standard Reference Frequency (Hz)

c. Accuracy Guaranteed for

d. Frequency Range

e, For single Phase Loads / In- put

f. For two Phase Loads / In - put

g. For In-put / Loads without neutral in -puts unbalanced Voltages

h. Temperature Range

7 Insulation Resistance

8 Sampling Plan for measurement of Voltage, Current and Frequency

9 Power Loss in each Current circuit at Basic Current in VA & WATT

10 Power Loss in each Voltage circuit at reference in VA & WATT

11 Display device (Hardware details)

a. Type of Display i.e. LCD

b. Character size of display digits

c. No. of Display digits used

2. For parameter identification

d. Life of display unit (Guaranteed)

e. Method adopted for digit over flow

12 Display details (Software)

13 a. Non-volatile memory retention time in absence of power

b. Non - volatile memory capacity in KB.

c. RAM Capacity

d. Maximum number of Parameters which can be stored in non-volatile Memory at each half an hour intervals for Six Months.

14 Maximum demand

a. Parameters that can be dynamically selected

b. Integration Period Range

c. Provision for Automatic Rest

d. Type of MD Computation

15 Communication Inter-phase available

- for calibration

- for data transfer

16 Electro magnetic interference / Electro magnetic comparativity level

17 Mounting arrangement

18 Meter sealing arrangement

b. Meter terminal block

c. MD reset bush button

d. Battery unit

19 Degree of protection against moisture etc.,

20 a. Provision for real time clock

b. Real time clock accuracy

c. Life of real time clock (Guaranteed)

21 Power Supply backup

22 Measuring principle employed for

d. Maximum demand parameters

NOTE 1. Measuring principle adopted for each of the items above should be specified.

2. Measurement logic employed in case of Harmonics and contents up to which meter recognizes for measurement shall be furnished.

23 Abnormal conditions that will be identified with limiting values

24 Guarantee period offered for

a. Performance and accuracy

b. Components not covered under guarantee

25 Micro processor

a. Address in bits

b. Sampling rate

26 Compatibility of the software for the following

a. For generation of consumer bill directly with the existing KPTCL billing software

b. Compatibility of software provided for MRI, down loading from earlier version already supplied to KPTCL

c. Compatibility of software for generation of report for earlier versions

27 Additional features available

28 Agreement to furnish protocol details for development of required software through third party

29 Platform on which the meter communicates

30 Levels of security

a. For changing real time

b. Fir changing display parameters

c. For changing Load survey parameters

d. For changing TOD Registers, clock setting

e. Measuring principle, computation

31 Specification of reference standard offered

32 Specification of Laptop Computer offered

33 Specification of MRI kit offered

34 Specification of equipment offered for checking communication capability through RS232/RS485 port

Place Designation

Name of the Company

Karnataka Power Transmission Corporation Limited

Bid Enquiry No: KPTCL/2026-27/SS/WORK_INDENT3928

Establishing 2X20 MVA, 66/11kV Sub-Station at Belaghatta along with Construction of 66kV DC Line on MC/DC Towers from 220/66kV Chitradurga S/S to Proposed 66/11kV Belaghatta S/S by Utilizing Cross arm of existing MC Towers (up to Gunuru Limits) along with Replacement of existing Coyote Conductor by HPC of ampacity 700amps Conductor for a distance of 11.394kms and Construction of 66kV SC Link Line on MC/DC Towers from Proposed 66/11kV Belaghatta S/S to Link existing 66kV Chitradurga - Turunuru SC Line for a distance of 0.210kms and Construction 01 No of 66kV Terminal Bay at 220/66/11KV sub station, Chitradurga to terminate the 66kV DC line to the proposed 66/11kV sub station Belaghatta in Chitradurga taluk & District on Partial Turnkey Basis including Supply of all matching Materials/Equipments (Excluding Supply 11kV Switchgear) and Erection (Including Dismantling and Civil Works) of all Materials/ Equipment, Testing and Commissioning.

TECHNICAL DATA SHEET

GUARANTEED TECHNICAL PARTICULARS FOR CIRCUIT BREAKERS

(Bidder is to indicate technical data for each type of rating)

Circuit Breaker Rating 145kV 72.5kV 33kV

a. Name of the Manufacturer

b. Country of Manufacture

c. Type of Circuit Breaker

d. Manufacturer's type designation

e. Standard Applicable

f. Rated Voltage (kV ms)

g. Rated Current :

i. Under normal condition (A)

ii. Under site conditions (A)

h. Rated frequency (Hz)

i. Number of poles

j. Whether 3 pole or single pole unit

k. Whether all the 3 poles ganged electrically or mechanically

l. Whether dead tank or live tank design

m. Type of installation

n. No. of break per pole

o. Latching Current (kA)

2 Guaranteed Ratings

a. Rated short circuit breaking current

i. Symmetrical component at highest system voltage (kA)

ii. DC Component (%)

iii. Asymmetrical breaking current at highest system voltage (kA)

b. Rated Making Capacity

i. At higher rated voltage (kAp)

ii. At lower rated voltage (kAp)

c. i. Maximum Total break time under any duty condition for any current up to rated breaking current with limiting conditions of voltage and pressure (ms)

ii. Rated breaking time (ms)

d. Closing time (ms)

e. Minimum opening time under any condition with limiting voltage and pressure (ms)

f. Maximum opening time under any condition with limiting voltage and pressure (ms)

g. Maximum close open time under any condition with limiting voltage and pressure (ms)

h. First pole to clear rating

i. Short time current rating (kA) for 1 Sec.

j. Rated operating duty

k. Maximum breaking capacity under kilometric faults and rated TRV characteristic (kAp)

l. Maximum breaking capacity under phase opposition (kAp)

m. Maximum line charging breaking current with temporary over voltage up to 1.4 p.u. (A)

n. Maximum over voltage (p.u.) on switching transformer on no load and corresponding charging current

o. Maximum period between closing of first contact & last contact in a pole (ms)

p. Maximum pole discrepancy (ms)

q. Maximum arc duration and corresponding current under lockout pressure.

r. Small fault current breaking capacity (kAp)

s. Pre-insertion resistor (if applicable)

i. Value / pole (Ohms) with tolerance

ii. Minimum and Maximum duration of insertion per pole (ms)

iii.Thermal rating for the c-1m-o-co-2m-c-1m-o-co for terminal fault considering maximum resistance and time setting.

iv. Thermal rating for the same duty as (iii) above for reclosing against trapped charges.

t. Maximum temperature rise for main contacts over design ambient temperature of 50oC

u. Rated voltage & pick up range for trip coil (V)

v. Rated voltage & pick up range for closing coil (V)

w. Rated pressure and limits of pressure of operating mechanism

x. Rated pressure and limits of pressure of extinguishing medium

y. Minimum dead time for

i. Three phase reclosing (ms)

ii. Single phase reclosing (ms)

z. Data of restriking voltage

i. Amplitude factor

ii. Phase factor

iii. Natural frequency

iv. Rate of rise of restriking voltage

3 Dielectric withstand of complete breaker

a. One minute dry & wet power frequency withstand voltage

i. Between live terminal and ground (kV rms)

ii. Between terminals with breaker contacts open (kV ms)

b. 1.2/50 micro impulse withstand test voltage

i. Between live terminals and ground (kVp)

ii. Between terminals with breaker contacts open (kVp)

c. Corona extinction voltage (kV rms)

d. Maximum radio interference voltage (micro V) at 1.1 Ur/v3

e. Total creepage distance

i. To ground (mm)

ii. Between terminals (mm)

4 Operating Mechanism

a. Type of operating mechanism for

b. Manufacturer's type designation

c. Normal power consumption (W) at rated voltage

ii. Closing coil

4.1 Pneumatic operating mechanism

a. Rated operating pressure (kg/sq.cm)

b. Range of pressure for (kg/sq.cm)

c. Air Consumption at rated pressure for

i. Closing (m3)

ii. Opening (m3)

iii. Close-open (m3)

d. Pressure drop/meter length of piping

e. Number and Capacity (m3) of breaker local air storage receivers

f. No. of close operations for which sufficient air is available in local receiver

g. Capacity of compressor (m3/hr) and working pressure (kg/cm2)

h. Maximum time for which compressor can operate continuously (min)

i. Time to fill

i. Air receiver after one CO operation (min)