Thematic Interior display and furnishing at Lobby at Assam State Museum, Ambari, Guwahati-01, Ambari, Guwahati - 01

Wood and P.V.C work

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S. piano hinges with necessary screws Providing & fixing false ceiling at all height including providing & fixing of framework made of special section, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleat of size 25mm wide x 1.6mm thick with flanges of 27mm and 37mm, at 1200mm c/c, one flange fixed to the ceiling with dash fastener 12.5mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25 x10 x0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I chanels 45 x15 x 0.90mm running at the spacing of 1200 mm c/c, to which the ceiling section 0.5mm thickbottom wedge of 80mm with tapered flanges of 26 mm each having lips of 10.5mm, at 450mm c/c, shall be fixed in a direction perpendicular to G.I intermediate channel with connecting clip made out of 2.64mm dia x 230mm long G.I wire at every junction, including fixing perimeter channels 0.50mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/ partitions with the help of Rawl plugs at 450mm centre, with 25mm long dry wall screws @ 230mm interval, including fixing of Calcium Silicate Board to ceiling section and perimeter channels with the help of dry wall screws of size 3.5 x25mm at 230mm c/c, including jointing & finishing to a flush finish of tapered and square edges of the board with recommended jointing compounds, jointing tapes,finishing with jointing compounds in three layers covering up to 150mm on both sides of joints and two coats of primer suitable for boards, all as per manufacture's specification and also including the cost of making opening for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specificaton and direction of the Engineer in charge but excluding the cost of painting with:

8 mm thick Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process.

Finishing

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications:

Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm

New technology and materials Providing & fixing in position Phenol bonded Bamboowood wall cladding at all height with planks of sizes 10mm thick, minimum 1800mm length and minimum 100 mm wide, in approved colour, texture and finish, having Performance Appraisal Certificate (PAC) issued by Building Materials & Technology Promotion Council (BMTPC), with necesasary profiled edges fixed with 40mm SS screws 5 nos in each tile to frame work made of second class teak wood of size 20x15 mm in centre of each tile and bottom and top of work height, 40x15mm placed at ends of each tile. The cladding shall be laid over backlayment of 1.00 mm thick expanded polyethylene foam of density 40kg/cum in two layers, first layer on wall surface before fixing wooden frame and second layer on frame under cladding. The bamboowood planks shall have minimum density of 1000 Kg/cum & minimum Hardness 1000 Kgf. with Eco friendly UV coating, all complete as per direction of the Engineer in-charge.

Supplying and Installation of Signage made of SS with minimum text height of each letter not less than 20cms of approved design inclusive all necessary fixtures

Supplying and Installation of 24 inch Brass main door handle of approved brand and make

Supplying and installation of vinyl printed display content , photographs, signages, etc. ( as approved design) pasted on sunboard as required.

Supplying and installation of cupboard and patch work, as per design, made of 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of desired quality and finished with desired finish complete in all respects with all accessories.

Thematic artwork at Ceiling dome including artist charge and material cost (dia 2.2m and dome height of 1 m)

Supplying and Installation of SS Ventilation Grille of approved brand and make

Supplying and installation of 3 seater bench of dimension (450mm x 1500mm x 450mm), as per design, made of 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of desired quality and finished with desired finish complete in all respects with all accessories.

Supplying and installation of Pedestal for object of the week, as per design, made of 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of desired quality and finished with desired finish complete in all respects with all accessories.

INTERNAL ELECTRICAL WORK

SUB HEAD-I: WIRING & SUBMAIN

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 2 way 5/6 A switch

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Supplying, Installation, Testing and Commissioning of picture light 7 watt warm white of approved brand and make

Supplying, Installation, Testing and Commissioning of 12 watt surface mounted square panel of approved brand

Supply, Installation, Testing and Commissioning of Exhaust Fan 300mm sweep of approved brand and make

Supply, Installation, Testing and Commissioning of PVC Junction box of approved brand and make

Supplying and installation of 12- 16 watt spot light of approved make and design.

Supplying, Installation, Testing and Commissioning of neon ropelight watt warm white of approved brand and make

Supplying, Installation, Testing and Commissioning of neon ropelight adapter of approved brand and make

Supplying, Installation, Testing and Commissioning of 12 watt track light of approved brand and make

Supplying, Installation, Testing and Commissioning of track light patti of approved brand and make