Special Repair of Renovation of Old SE Office in PWD B R Office at Kaithal In Kaithal Distt

Amount

Supply of G.I.pipe of work of class B. (NS) 15 mm i/d

Pdg. & Fixing of Wall Panaling i/c all necessary fittings complete in all respect (NS).

Dismantling of existing interlocking paver blocks pavement including transporting and stacking usable block along road side and dispose unusable blocks out sides PWD land or desired by Engineer (HSR 8.2 (b)))

Providing and laying 150 mm thick granular sub base consisting of drainage layer confirming to Table 400.1 Grading –VI of MoRT&H 5th edition, mixing in a mechanical mix plant at OMC, carriage of mix material to the site of work, spreading in uniform layer with motor grader on prepared surface and compacting with vibratory power roller to achieve desired density complete as per clause No. 401 of MoRT&H specifications. Note: - 1.Only crushed metal material should be used. No local earth sand shall be used. The material finer than 425 micron shall have zero Plasticity Index (PI). 2. Material to be used and operations of manufacturing shall be approved by engineer.

Earth work in excavation in foundations, trenches, etc.in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres (HSR 6.6)

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing in cement (HSR 8.5 (b))

Dismatnling Roofing Removing R.C.C.Battens from roof (HSR 8.8 (h))

Dismantling of Floor Tiles complete in all respect. (HSR 8.26)

Scraping cement plaster. (HSR 8.32 (c)).

Cement Concrete 1:4:8 with stone aggregate 20mm nominal size in foundation and plinth. (HSR 10.38)

Cement Concrete 1:2:4 with stone aggregate 20mm nominal size in foundation and plinth. (HSR 10.41)

Cement concrete 1:1½:3 with stone aggregate 20 mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centring and shuttering, laid in position complete in all respects (HSR 10.82+10.95 (a))

Providing and laying 80mm thick ISI Marked interlocking paver blocks conforming to IS 15658 2006 / IRC SP 63-2004 of all shapes and colours in design mix cement M-40 over a bed of 30mm thick fine sand complete in all respect. (HSR 10.159)

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 meters above plinth level. (HSR 11.7)

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster a nd on other layer of mud mortar for laying the tiles, including two coasts of bitumen laid hot at 1.65 Kg per sqm on top of R.C.C. slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13)

Cement concrete 1:2:4 gola 10cm x 10 cm quadrant along junction of roof with parapet wall finished smooth (HSR 13.64)

Providing fixing PVC Rain water pipe 6Kg Pressure of ISI mark in cement mortar during masonry work. (a) 100 MM dia PVC pipe 6 Kg. Pressure. (HSR 13.89 (a))

Providing & fixing PVC Bend ISI Mark (a) 100 mm dia PVC Bend (HSR 13.90 (a))

Providing and fixing False Ceiling with 12mm thick Gypsum Board fixed on M.S. Steel runners frame i/c cost of screws angles, cleats, rawel plugs, with taping, filling with Gypsum compound and applying priming coat, etc. complete in all respects.(HSR 13.91)

Base course of floors consisting of 100 mm thick cement concrete 1:8:16 and 100 mm sand or stone filling. (HSR 14.1)

Fixing Marble stone flooring 17mm thick and above thick slab i/c matching the grains of marble laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of marble i/c rubbing and polishing (excluding the cost of marble) (HSR 14.49) (a)) Kitchen Slab Pantary

Providing and fixing vitrified tiles of size 600 x 600mm of approved make in flooring laid in any pattern as specified over base of 20mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles. Note:-Tile shall be of premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT & JOHNSONS.(HSR14.89)

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete (a) Size of ceramic Glazed tiles 200 X 300mm (HSR 14.92 (a))

12 mm thick cement plaster 1:4 (HSR 15.5)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or matallic or plastered or concrete surfaces to give an even shade. (HSR 16.3)

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (HSR 16.5)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces. (HSR 16.25)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (HSR 16.58)

Providing two coats of exterior acrylic emulsion paint a) 2nd Quality (HSR 16.79 (a))

Providing and Applying two coats white cement based putty over plastered surface and grinding the surface smoothwith sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete (J.K. / Birla make) (HSR 16.81)

Wire gauze commercial hard wood such as hollock, champ, chikrassy etc. (non-coniferous timber other than teak conforming to I.S. specification No. 1003 kiln seasoned) door and window shutters without springs housed in chowkats including chocks, iron hinges and screws, etc., complete fixed in position (excluding the cost of tower bolts and handles but including the labour for fixing the same). (a) 30 mm thick (HSR 17.31 (i))

Factory manufactured panelled door or glazed window, shutters of commercial hard wood, such as hollock, champ,chikrassy and chaplash,etc., (non-coniferous timber other than teak,conforming to I.S.specification No.1003,kiln-seasoned), with 100 mm wide verticle styles, 150 mm wide lock rail, 200 mm wide bottom rail and 100 mm wide other rails, with panels of 15 mm thick, tongued and grooved of commercial hard wood and including cost of iron hinges, screws, chocks / cleats, stops,nails etc., complete, fixed in position (excluding the cost of any fittings, other than specified above,but including labour for fixing the same in position). (a) 30 mm thick (HSR 17.90 (a))

Factory manufactured solid flush door shutters, with block board core as per I.S.No.1659- 1969 bonded with water proof type phenol formaldehyde synthetic resin,hotpressesd, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges,screws, chocks /cleats and stops etc.(excluding the cost of any fittings other than specified above,but including labour for fixing the same in position)- (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges.) (ii) 30 mm thick (HSR 17.93 (a) (ii))

Steel reinforcement TMT bars FE-500 EQR / FE-500 D grade or more for RCC work, where no included in the complete rate of RCC including straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position complete in all respects for all heights / depths / storeys / basements etc. Note: Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work, excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement.. (HSR 18.22)

Labour for fixing G.I. or W.I. pipe sleeve pieces in holes in walls floors and roofs rounds pipes including all cutting and 16wastage (HSR 28.27) 15 mm i/d

CONSTRUCTION OF RECTANGULAR STANDARD BRICK MASONRY MANHOLE CHAMBERS to standard drawings on new. Egg-shaped sewers upto the required depth in 1:5 CEMENT SAND MORTAR, LIME CONCRETE 40 percent lime mortar with 19-20 mm gauge brick ballast in haunches above the arch ring where the depth of cover in traffic streets is LESS THAN 1.5 METRES, 12MM THICK WATER TIGHT 1:2 CEMENT SAND PLASTER WITH A FLOATING COAT OF NEAT CEMENT and finished with two coats of sodium silicate on INTERIOR SURFACE where required, reinforced cement concrete slab 180mm THICK FIXING 560 MM INTERNAL DIAMETER C.I.MANHOLE FRAME AND COVER weight not less than 2.5 quintal painted with 3 COATS OF BLACK BITUMEN PAINT, fixing galvanised melleable iron steps embedded in 1:2 cement sand mortar etc., complete. The rate also covers the cost of M.S. steel for R.C.C. slab labour for fixing and carriage of C.I. manhole frame and cover and melleable iron steps from the stores of the Engineer-in-charge of the works to site of works. The rate further includes cost of accurately planned and fitted centring, supports for all works, as well as for all curves and specials work cleaning out their beds, etc. sodium silicate shall be supplied free of cost at the stores of Engineer-in-charge. (I) On egg-shaped sewers of size 610mm X 915 mm to 860 mm X 1290 mm (a) for 2.40 meters depth below ground level (HSR 29.89 (I (a))

PROVIDING AND FIXING IN POSITION BEST INDIAN MAKE (as approved by the Engineer-in-charge) EUROPEAN TYPE WATER CLOSET SUIT, SYPHONIC TYPE, consisting of- VITREOUS CHINA WARE SYPHONIC SUITE WITH 15 LITRES CAPACITY MATCHING CHINAWARE CISTERN and all internal brass fittings COMPLETE WITH ‘P’ or ‘S’ TRAP with or without vent; (as approved by the Engineer-in-charge). One Piece SEAT AND LIDIN HOLLOW BLACK OR WHITE PLASTIC fitted with chromium plated hinges and rubber buffers,(to the approval of the Engineer-in-charge). Complete in all respects INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOORS.(a) Single trap syphonic W.C. Suite (i) White (HSR 30.5 (a) (i))

Providing and fixing 15 litres capacity viteous china high level cistern complete white (HSR 30.8)'

Extra for 32 MM G.I./C.P. flush pipe of 32 mm dia G.I. flush pipe. (HSR 30.15 (a))'

PROVIDING AND FIXING POSITION BEST INDIAN MAKE FLAT BACK OR ANGULAR LIPPED FRONT URINAL 465 MM HIGH CONSISTING OF : -(i) Flat back lipped or angular urinal basin of VITREOUS CHINA WARE (to the approval of the Engineer-in-charge). (ii) 5 LITRES CAPACITY mosquito proof INDIAN MAKE C.I.AUTOMATIC FLUSHING CISTERN, PAINTED WITH non-yellowing white enamel paint or other approved shade enamel paint on outside and superior black bitumastic paint on inside complete with screwed 15 mm pipe; (iii) PAIR OF R.S.PR C,I. PAINTED BRACKETS AND BRASS COUPLINGS; (iv) Standard size G.I.FLUSH PIPE WITH C.P.BRASS WALL CLIPS AND UNIONS COMPLETE INCLUDING CUTTING AND MAKING GOOD THE WALLS AND FLOOR AND PAINTING OF FITTINGS ETC. (as required by the Engineer-in-charge). (i) White (HSR 30.19 (a))

Providing and fixing in position best Indian make beveled edge 5.5 mm thick mirror ground fixed in position by means of 4 Nos chromium plated brass screws and washers complete including cutting and With vitreous china frame of size 530 mm x 430mm White. (HSR 30.71 (b) (i))) '

Providing and fixing in position 15mm i/d C.P. brass bib cocks of best quality ( as required by the Engineer-in- Charge (HSR 30.75) Short Bib cock

Long Bib cock

Providing and fixing in position C.P. brass stop cocks ( as approved by the Engineer-in-charge) (HSR 30.76) 15 mm stop Cock

Stop cock male and female end Concealed stop cock' (HSR 30.76 (a) (ii))

PROVIDING AND FIXINGIN POSITION H.C.I.SOIL WASTE VENT OR ANTISYPHONAGE PIPES TO I.S.I. SPECIFIACTION OF E.L.C. MANUFACTURE OR OF ANY OTHER REPUTED FIRM INCLUDING CUTTING AND WASTAGE ETC. AND CUTTING HOLES IN WALLS, ROOFS OR FLOOR ETC.AND MAKING GOOD to its original condition BUT EXCLUDING COST OF LEAD JOINTING (a) 100 mm internal diameter (HSR 30.84 (a))

Providing and fixing HDPE water storage tanks of Sintex, Diplast, O.K. make with covers/lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in- Charge. (except civil work). (e) 1000 ltr. capacity (HSR 30.119 (e))

Recovery Items:- The rates quoted against recovery items will not be included in the total amount rather it will be deducted while calculating financial statement of the agency. Material obtained from dismantling of existing brick work, bituminous layer have been calculated taking assumption that 80% of theoretical material will be retrieved. The dismantled material can used in any of the item for the work after modification (bringing it to required specifications) after approval from employer. In case it is not possible to use this material on the work, the agency can take away this material. This material can be taken away by the agency at the price quoted by the agency but minimum price to be quoted is limited to reserve price as fixed and mentioned as under :- Bricks / Tiles @ 4.50/- Each

Bricks Bats @ 450/- P. Cum Note:- In case of any difference in the unit & nomenclature of any of the HSR Items of Civil, P.H. work depicted in this DNIT and that given in HSR, the unit and nomenclature given in HSR shall be applicable.

The Teg Bahadur Co-Op L/C Society Limited Siwan

The Atela Janta Co op L and C Society Ltd